Torque Limiter 0 Series Overview Torque Limiter 0 Series
Torque Limiter 0 Series For more than 80 years, Autogard products have led the industry in overload protection with high-quality products, design innovation and production. Autogard products are manufactured to meet ISO 900 using the latest machine tools and high-quality materials. Acting like a mechanical circuit breaker to protect the weakest member of the drive train, the most effective location for Autogard Torque Limiters is as close as possible to the component being protected. The 0 Series has been designed to meet the need for a compact and reliable safety clutch. The optimized design provides a robust, backlash-free clutch that will protect equipment from the damaging effects caused by overloading a drive train. The 0 Series is offered in two reengagement styles. The SR Reset features a timed automatic re-engagement as a standard. An un-timed reset version is also available. The MR Reset is a manual re-engagement and accommodates higher-speed applications, and is capable of running continuously in the disengaged condition. Disengagement on Overload In the normal drive condition, torque is transmitted through drive balls A that are located in holes in flange B and detents in drive plate C. The drive balls are held in the detents under pressure from springs D. When the driven machine either jams or an overload occurs which is greater than the torque setting, the balls roll out of their seats. Re-engagement Re-engagement occurs in one of two ways depending upon which series is selected. 0 Series Applications Conveyor Drives Vacuum Pumps Coal Feeder Conveyor Packaging Equipment Tool and Die Figure E G B C Letters above correspond to paragraphs on the left and below. Re-engagement SR Reset Re-engagement is automatic once the overload is removed. Ball detents are positioned in a scattered pattern so that the balls must return to their original position before they can reset. Reengagement will occur within one revolution in either direction. Immediate shutdown is required to prevent wear of the detents. Re-enagement MR Reset Upon overload, the drive balls roll out of their seats and push the pressure plate E and control balls G into a position such that the drive balls are held away from the drive plate seats preventing re-engagement. The MR Reset remains disengaged and can run freely on a bearing J. A proximity sensor or limit switch can be used to detect this movement, sending a signal to a warning device or control system to shut down the motor. Re-engagement of the torque limiter is easy. Simply insert a screwdriver (or similar tool) between the pressure plate and the spring plate, and twist slightly. The unit will snap back into engagement, at any position. J A D
Features and Benefits: Accurate torque limitation prevents costly downtime caused by overloads Compact design reduces weight and inertia on the equipment Bi-directional operation The standard design can accommodate larger torque ranges than many other models currently available Offered in a larger number of styles ensuring the right solution is available for all applications Backlash-free operation Offered in automatic and manual re-engagement One revolution synchronous re-engagement offered Manual reset after tripping can be easily reset, at any position High-speed applications supported with free-running disengagement featured in the MR Reset Springs can be inspected and changed without removing the clutch from the drive train Coil springs allow one standard design to accommodate the full torque range as opposed to regressive disc springs that can only accommodate a narrow torque band Selection: Data required for torque limiter selection: Application details for service factors Kilowatt (kw) or horsepower (hp) and rpm of the driver Shaft details of the driving and driven equipment () Calculate the nominal torque. Torque (lb-in) = hp x 605 / rpm Consideration should then be given to start torque or other special circumstances depending on the position chosen in the drive system. Choose a set torque with a suitable margin over nominal. Select the torque limiter which has a higher torque rating. () Check limiting conditions: (a) Check running speed (b) Check hub bore capacity (c) Check the torque limiter dimensions such as the overall length and outside diameter () Select and specify the appropriate drive medium or coupling. All 0 Series units may be supplied from the factory at a pre-set torque and with the required drive medium assembled to the unit. Bore options with conventional bore and key or cone clamp sleeve for keyless connection Ordering the 0 Series Torque Limiter When ordering, please provide the following designation: Model and / Type / Reset / S or S bore / S bore Standard bore tolerance = H8 + normal fit key Example: 0- / 8 / SR / S75 / S-6 Refers to a 0 Series,, Type 8 torque limiter designed for Single Position Reset S Bore =.75 in S Bore =.6 in Also specify setting torque and/or pulley or sprocket if required. The specifications contained within this brochure are correct at the time of going to print. Rexnord is continually reviewing and updating the specifications on its entire Autogard product offering and therefore reserve the right to change any detail.
0 Series SR Standard Hub Type - Figure Type - Figure K X ON TRIP L Ø S Ø D Ø A (OPTION) L Table Torque Max. Speed Weight Mass Moment of Inertia MR Min. Max. Hub Side Flange Side lb-in lb-in rpm lb lb-in lb-in 0 7 44 00..67 0.4 0 44 885 00 4..075.709 89,770 00 6.4 6.49.47 77,540 00 9.8 5.05 6.84 0 6,96 00 6..0.668 4 664,76 00 8.5 87.87 7.45 See page 7, Table, for spring and torque ranges with specific springs. Weights and inertia values are for unbored units. Table For use with sprockets, pulleys or gears. Type contains keyless bore clamp bushing. Type accommodates a parallel bore and key. Bore (S) Clamped Collar Bore (S) Keyed Hub Min. Max. Max. A B D E F G H J K K L L L M X in in in in in in in in holes mm in in in in in in in in 0 0.9 0.79 0.79.5 0.8.68.50.05 8 M4 0.4 0.0 0..85.97.05.8504 0.05 0 0.59.0 0.94.94.0..0.795 8 M5 0. 0.8 0.4.6.56.68.4409 0.06 0.87.8.6 4.57.0.94.69.46 8 M6 0.9 0.8 0.47.80.0.5.958 0.07.6.77.57 5.5.50 4.7 4.7.97 8 M6 0.50 0. 0.47..54.74.54 0.09.8.7.97 6.0.65 5.0 5.00 4.567 8 M8 0.50 0. 0.6.74.98 4..970 0.09 4.65.56.8 7.48.9 6.54 6.8 5.669 8 M0 0.7 0. 0.6 4. 4.65 4.80 4.576 0. Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. The drive medium must be bored to suit dimension M. Clutches may be ordered complete with drive medium (v-belt pulleys, timing pulleys, etc). 4
Table Smallest Pulley Smallest Sprocket (No. of teeth) Diameter /8 in pitch / in pitch 5/8 in pitch /4 in pitch in pitch in 0 5 9 6 4.6 0 0 9 7.99 5 7 9 5.58 4 6 7 4.7-5 9 5 9 4.88 4 - - 5 0 6.06 The pulley diameter quoted is to the bottom of the V-pulley groove or the inside diameter for the flange of the timing pulley. 5
0 Series SR Long Projecting Hub Type - Figure 4 Type 4 - Figure 5 W G HOLES THREAD H x J DEEP L Ø S Ø D Ø A (OPTION) B L Table 4 Torque Max. Speed Weight Mass Moment of Inertia MR Min. Max. Hub Side Flange Side lb-in lb-in rpm lb lb-in lb-in 0 7 44 00.6.67 0.68 0 44 885 00 5.0.47.050 89,770 00 7.7 6.84 4.00 77,540 00.4 6.40 8.54 0 6,96 00 9.9 5.95 6.40 4 664,76 00 4.9 94.65 44.079 See page 7, Table, for spring and torque ranges with specific springs. Weights and inertia values are for unbored units. Table 5 For use with sprockets, pulleys or gears. Type contains a keyless bore clamp bushing. Type 4 accommodates a parallel bore and key. Bore (S) Clamped Collar Bore (S) Keyed Hub Min. Max. Max. A B D E F G H J K L L L M W W X in in in in in in in in holes mm in in in in in in in in in 0 0.9 0.79 0.79.5 0.8.68.50.05 8 M4 0.4.8.8.95.0.8504.0 0.6 0.05 0 0.59.0 0.94.94.0..0.795 8 M5 0..57.66.8.98.4409.69 0. 0.06 0.87.8.6 4.57.0.94.69.46 8 M6 0.9.77 4.5 4.7 4.84.958.7 0.5 0.07.6.77.57 5.5.50 4.7 4.7.97 8 M6 0.50.7 5.47 5.7 5.9.54.64 0.4 0.09.8.7.97 6.0.65 5.0 5.00 4.567 8 M8 0.50.56 5.98 6. 6.8.970.87 0.4 0.09 4.65.56.8 7.48.9 6.54 6.8 5.669 8 M0 0.7.95 7.8 7.60 7.76 4.576.58 0.4 0. Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. The drive medium must be bored to suit dimension K and supported with suitable bearing. Clutches may be ordered complete with drive medium (v-belt pulleys, timing pulleys, etc). 6
Table 6 Smallest Pulley Smallest Sprocket (No. of teeth) Diameter /8 in pitch / in pitch 5/8 in pitch /4 in pitch in pitch in 0 9 5 9.77 0 6 0.7 5 9 6 4.76 9 8 6.5-6 8 5.94 4 - - 0 6 4. The pulley diameter quoted is to the bottom of the V-pulley groove or the inside diameter for the flange of the timing pulley. 7
0 Series SR Torsionally Rigid ES - Figure 6 Type 5, EB - Figure 7 Type 6, EB - Figure 8 K X ON TRIP G L Ø D Ø D Ø S SEE NOTE L L Ø S L Ø S Ø D Ø A (OPTION) L L L5 L4 Table 7 Min. Torque Max. Max. Speed Weight Mass Moment of Inertia MR Hub Side Flange Side lb-in lb-in rpm lb lb-in lb-in Angular Angular Max. Coupling Misalignments EB ES EB ES EB ES Axial in Axial in Parallel in Parallel in Combined 0/8 7 44 00 4.9 4.44.759 0.5 0.0 0.0 0.00 0.0 0.0 0/8 44 885 00 6.7 5.809 4.44 0.5 0.0 0.0 0.00 0.0 0.0 /5 89,770 00 0.5.985 0.5 0.5 0.0 0.0 0.00 0.0 0.0 /5 77,540 00 7.7.45 4.944 0.5 0.0 0.04 0.00 0.0 0.04 /70 0 6,96 00 9. 7.78 54.0 0.5 0.0 0.05 0.00 0.0 0.05 4/50 664,76 00 55.9 6.05 75.64 0.5 0.0 0.06 0.00 0.0 0.06 See page 7, Table, for spring and torque ranges with specific springs. Weights and inertia values are for unbored units. This is the maximum variation in G measured around the periphery. It corresponds to the maximum combined angular, axial and parallel misalignments. Table 8 Includes the Autoflex EB torsionally rigid metal membrane coupling for angular and axial misalignment. The Autoflex ES double flex spacer coupling can also be supplied to accommodate angular, axial and parallel offset misalignment. Type 5 contains a keyless bore clamp bushing. Bore (S) Clamped Collar Bore (S) Keyed Hub Min. Max. Max. Max. Bore (S) Keyed Hub A D D D G G K L L L L L4 L5 X in in in in in in in in in in in in in in in in in in 0/8 0.9 0.79.8 0.79.5.68.7.5 0.9.89 0.9.90.85.8.05 4.09 4.0 0.05 0/8 0.59.0.8 0.94.94..7.5 0.9.89 0.9 4.65.40.8.68 4.9 4.80 0.06 /5 0.87.8.57.6 4.57.94.09.50 0.9.89.06 5.0.8.44.5 5.5 5.5 0.07 /5.6.77.97.57 5.5 4.7.80 4. 0.7.8.0 6.8.5.8.74 6.77 6.54 0.09 /70.8.7.76.97 6.0 5.0.58 5.4 0.7.8.77 7.09.74.6 4. 7.48 7.8 0.09 4/50.65.56.54.8 7.48 6.54 4.84 6.69 0.5.5. 8.4 4..89 4.80 8.90 8.74 0. Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. G is for minimum DBSE, longer spacers are available. 8
0 Series SR Elastic Coupling Type 7 - Figure 9 Type 8 - Figure 0 K X ON TRIP Ø D Ø D Ø D Ø S L L Ø S L L5 Table 9 Torque Mass Moment of Inertia MR Max. Weight Coupling Misalignment Min. Max. Speed Max. Radial/ Hub Side Flange Side Max. Axial Parallel Max. Angular lb-in lb-in rpm lb lb-in lb-in in in degrees 0/A 7 44 00 4. 4.00.47 +0.0 0.0 0/A 44 885 00 8.79 6.40 5.05 +0.0 0.00 /A 89,770 00 5.70 58.77 56.09 +0.0 0.00 /A 77,540 00 9.0 66.97 58.77 +0.0 0.00 /A4 0 6,96 00 4.5.67. +0.0 0.08. 4/A45 664,76 00 5.99 40.864 5.9 +0.04 0.08. See page 7, Table, for spring and torque ranges with specific springs. Weights and inertia values are for unbored units. Table 0 Model includes the Samiflex coupling which accomodates angular, axial and parallel offset misalignments. Type 7 contains a keyless bore clamp bushing. Bore (S) Clamped Collar Bore (S) Coupling Hub Bore (S) Keyed Hub Min. Max. Min. Max. Max. A D D D D G L L L L L4 L5 X in in in in in in in in in in in in in in in in in in 0/A 0.9 0.79 0.59. 0.79.5.68.56.56.7 0.59.8.85.8.05 4.0.94 0.05 0/A 0.59.0 0.7.7 0.94.94..5.9 4.7 0.8 5.00.40.8.68 5.8 5.4 0.06 /A 0.87.8 0.79.6.6 4.57.94.5 4.57 5.67.4 6.4.8.0.5 6.46 6.8 0.07 /A.6.77 0.79.6.57 5.5 4.7.5 4.57 5.67. 6.7.5.0.74 7. 6.9 0.09 /A4.8.7 0.98.9.97 6.0 5.0 4. 5.9 7.7.4 7.64.74.48 4. 8.0 7.87 0.09 4/A45.65.56.0.56.8 7.48 6.54 4.9 6.69 7.95.4 8.4 4..76 4.80 8.90 8.74 0. Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. 9
0 Series MR Standard Hub Type - Figure Type - Figure K B N K G HOLES THREAD H x J DEEP K X ON TRIP L L Ø E Ø F Ø M h6 Ø S Ø C Ø A Ø S L Table Min. Torque Max. Max. Speed Weight Mass Moment of Inertia MR lb-in lb-in rpm lb lb-in 0 5 5 8,000.0.709 0 89,5 7,000 4.9.47 77,947 6,000 6.9 0.5 54 4,45 5,000 9.9 0.50 708 7,08 4,000 6.0 44.4 4,46 5,9,000 8.6 6.680 See page 7, Table, for spring and torque ranges with specific springs. Higher speeds may be allowed under certain conditions. Consult Rexnord. Weights and inertia values are for unbored units. Table For use with sprockets, pulleys or gears. Type contains a keyless bore clamp and bushing. Type accomodates a parallel bore and key. Bore (S) Clamped Collar Bore (S) Keyed Hub Min. Max. Max. A B C E F G H J K K K L L L M N X in in in in in in in in holes mm in in in in in in in in in in 0 0.9 0.79 0.79.94 0.6.5.5.05 8 M4 0. 0.0 0. 0.59.85.97..8504 0.06 0.09-0. 0 0.59.0 0.94 4.5 0.8...795 8 M5 0.9 0.8 0.4 0.75.40.60.7.4409 0.06 0.0-0. 0.87.8.6 5..0.70.70.46 8 M6 0.9 0.8 0.47 0.75.80.0.07.958 0.08 0.-0.6.6.77.65 5.9.4 4.49 4.7.97 8 M6 0.9 0.5 0.47 0.9.46.70.86.54 0. 0.4-0.9.8.7.97 6.50.4 4.96 4.96 4.567 8 M8 0.5 0. 0.6.0.78 4.0 4.7.970 0. 0.6-0. 4.65.56.40 7.87.65 6.6 6.6 5.669 8 M0 0.7 0. 0.6.0 4.4 4.7 4.84 4.576 0. 0.9-0.6 Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. The drive medium must be bored to suit dimension M. Clutches may be ordered complete with drive medium (v-belt pulleys, timing pulleys, etc). 0
Table Smallest Pulley Smallest Sprocket (No. of teeth) Diameter /8 in pitch / in pitch 5/8 in pitch /4 in pitch in pitch in 0 5 0 7 4.6 0 0 9 7 4.99 5 7 9 5.58 40 6 8 4.7-5 9 5 9 4.88 4 - - 5 0 4 6.06 The pulley diameter quoted is to the bottom of the V-pulley groove or the inside diameter for the flange of the timing pulley.
0 Series MR Long Projecting Hub Type - Figure Type 4 - Figure 4 Table 4 Min. Torque Max. Max. Speed Weight Mass Moment of Inertia MR lb-in lb-in rpm lb lb-in 0 5 5 8,000.6.050 0 89,5 7,000 5. 6.84 77,947 6,000 7.7 0.5 54 4,45 5,000. 4.70 708 7,08 4,000 0.0 68.40 4,46 5,9,000 5. 6.680 See page 7, Table, for spring and torque ranges with specific springs. Higher speeds may be allowed under certain conditions. Consult Rexnord. Weights and inertia values are for unbored units. Table 5 For use with sprockets, pulleys or gears. Type contains a keyless bore clamp bushing. Type 4 accomodates a parallel bore and key. Bore (S) Clamped Collar Min. Max. Max. Bore (S) Keyed Hub A B C E F G H J K L L M N W W X in in in in in in in in holes mm in in in in in in in in in 0 0.9 0.79 0.79.94 0.6.5.5.0 8 M4 0...8.0.9 0.. 0. 0.09-0. 0 0.59.0 0.94 4.5 0.8...80 8 M5 0..4.7.9.4 0..7 0. 0.0-0. 0.87.8.6 5..0.70.70.5 8 M6 0.4.8 4.5 4.7.0 0.. 0. 0.-0.6.6.77.65 5.9.4 4.49 4.7.94 8 M6 0.4. 5.7 5.9.5 0..7 0.4 0.4-0.9.8.7.97 6.50.4 4.96 4.96 4.57 8 M8 0.5.6 6.0 6..9 0..9 0.4 0.6-0. 4.65.56.40 7.87.65 6.6 6.6 5.67 8 M0 0.7.0 7.4 7.7 4.5 0..6 0.4 0.9-0.6 Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. The drive medium must be bored to suit dimension M. Clutches may be ordered complete with drive medium (v-belt pulleys, timing pulleys, etc).
Table 6 Smallest Pulley Smallest Sprocket (No. of teeth) Diameter /8 in pitch / in pitch 5/8 in pitch /4 in pitch in pitch in 0 9 5 9.77 0 6 0.7 5 9 6 4.76 9 8 6.5-6 8 5.94 4 - - 0 6 4. The pulley diameter quoted is to the bottom of the V-pulley groove or the inside diameter for the flange of the timing pulley.
0 Series MR Torsionally Rigid ES - Figure 5 Type 5, EB - Figure 6 Type 6, EB - Figure 7 G N X ON TRIP L L L Ø D Ø D Ø S Ø S Ø C Ø A K L5 Table 7 4 Torque Mass Max. Coupling Misalignments Max. Weight Moment Min. Max. Speed of Inertia EB ES EB ES EB ES MR lb-in lb-in rpm lb lb-in Angular Angular Axial in Axial in Parallel in Parallel in Combined 0/8 5 5 8,000 4.9 6.84 0.5 0.0 0.0 0.00 0.0 0.0 0/8 89,5 7,000 6.7 0.5 0.5 0.0 0.0 0.00 0.0 0.0 /5 77,947 6,000 0.5.99 0.5 0.0 0.0 0.00 0.0 0.0 /5 54 4,45 5,000 7.6 68.40 0.5 0.0 0.04 0.00 0.0 0.04 /70 708 7,08 4,000 9. 6.680 0.5 0.0 0.05 0.00 0.0 0.05 4/50,46 5,9,000 55.9 40.040 0.5 0.0 0.06 0.00 0.0 0.06 See page 7, Table, for spring and torque ranges with specific springs. Higher speeds may be allowed under certain conditions. Consult Rexnord. Weights and inertia values are for unbored units. This is the maximum variation in G measured around the periphery. It corresponds to the maximum combined angular, axial and parallel misalignments. 4 Table 8 Includes the Autoflex EB torsionally rigid metal membrane coupling for angular and axial misalignment. The Autoflex ES double flex spacer coupling can also be supplied to accommodate angular, axial and parallel offset misalignment. Type 5 contains a keyless bore clamp bushing. Type 6 accomodates a parallel bore and key. Bore (S) Clamped Collar Bore (S) Keyed Hub Min. Max. Max. Max. Bore (S) Keyed Hub A C D D G G K L L L L L4 L5 N X in in in in in in in in in in in in in in in in in in in 0/8 0.9 0.79.8 0.79.94.5.7.5 0.9.89 0.9.90.85.8.4 4.9 4.06 0.06 0.09-0. 0/8 0.59.0.8 0.94 4.5..7.5 0.9.89 0.9 4.65.40.8.80 5.04 4.84 0.06 0.0-0. /5 0.87.8.57.6 5..70.09.50 0.9.89.06 5.6.80.44. 5.67 5.9 0.08 0.-0.6 /5.6.77.97.65 5.9 4.49.80 4. 0.7.8.0 6.50.46.8 4. 7.7 6.7 0. 0.4-0.9 /70.8.7.60.97 6.50 4.96.58 5.4 0.7.8.77 7..78.6 4.4 7.76 7.6 0. 0.6-0. 4/50.65.56.54.40 7.87 6.6 4.84 6.69 0.5.5. 8.50 4.4.89 5. 9. 8.8 0. 0.9-0.6 Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. G is for minimum DBSE, longer spacers are available. 4
0 Series MR Torsionally Soft Coupling Type 7 - Figure 8 Type 8 - Figure 9 G N X ON TRIP L L L Ø D Ø D Ø D Ø S Ø S Ø C Ø A L5 Table 9 Torque Max. Speed Max. Speed Weight Mass Moment Coupling Misalignment Min. Max. Unbalanced Balanced of Inertia MR Max. Axial Max. Radial/Parallel Max. Angular lb-in lb-in rpm rpm lb lb-in in in degrees 0/A 5 5 7,50 8,000 4. 6.84 +0.0 0.0 0/A 89,5 5,440 6,500 8.8 0.75 +0.0 0.00 /A 77,947 4,00 4,800 5.7 6.78 +0.0 0.00 /A 54 4,45 4,00 4,800 9.0 6.49 +0.0 0.00 /A4 708 7,08,75,600 5. 444.0 +0.0 0.08. 4/A45,46 5,9,800,000 55. 75.740 +0.04 0.08. See page 7, Table, for spring and torque ranges with specific springs. Higher speeds may be allowed under certain conditions. Consult Rexnord. Weights and inertia values are for unbored units. Table 0 Model includes the Samiflex coupling which accomodates angular, axial and parallel offset misalignments. Type 7 contains a keyless bore clamp bushing. Type 8 accomodates a parallel bore and key. Bore (S) Clamped Collar Bore (S) Coupling Hub Min. Max. Min. Max. Max. Bore (S) Keyed Hub A C D D D G L L L L L4 L5 N X in in in in in in in in in in in in in in in in in in in 0/A 0.9 0.79 0.59. 0.79.94.5.56.56.7 0.59.8.85.8.4 4..98 0.06 0.09-0. 0/A 0.59.0 0.7.7 0.94 4.5..5.9 4.7 0.8 5.00.40.77.80 5.9 5.0 0.06 0.0-0. /A 0.87.8 0.79.6.6 5..70.5 4.57 5.67.0 6.0.80.0. 6.6 6.4 0.08 0.-0.6 /A.6.77 0.79.6.65 5.9 4.49.5 4.57 5.67.8 6.85.46.0 4. 7.5 7.09 0. 0.4-0.9 /A4.8.7 0.98.9.97 6.50 4.96 4. 5.9 7.7.4 7.68.78.48 4.4 8. 7.9 0. 0.6-0. 4/A45.65.56.0.56.40 7.87 6.6 4.9 6.69 7.95.4 8.50 4.4.76 5. 9. 8.8 0. 0.9-0.6 Bores are furnished for clearance fit unless otherwise specified by customer. Consult Rexnord. Rectangular keys must be used for maximum bore diameters. 5
Engineering Information Torque Setting The full torque capabilities of the 0 Series will depend on the number of springs fitted. A full complement of springs gives the catalog maximum values. See Table below. Table : Spring Selection 0 Series SR No. of Springs 0 0 4 Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in 7 06 44 50 89 66 77 60 0 885 664, 4 44 89 0 77 5 54,9 60,99,8 4,45 8 89 44 77 60 54,06 708,0,9,98,655 8,85 - - 66 885 5,770,06,540,770 6,96,98,76 Table : Spring Selection 0 Series MR No. of Springs 0 0 4 Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in lb-in 5 06 89 77 77 54 54 708 708,46,46,8 4 06 66 77 54 54 708 708,46,46,9,8 5,664 8 5 54 708 708,8,46,9,8 4,69 5,664 0,6 - - 5,5,06,947,4 4,45 4,48 7,08 8,497 5,9 Drive Shutdown on Disengagement 0 Series SR The 0 Series SR torque limiter is designed to run at speeds up to 00 rpm, but the service life is determined by the number of rotations after disengagement. No wear occurs while the torque limiter is engaged. The life of the unit when running tripped depends on the torque setting, the running speed, and the time it takes to stop the drive after an overload occurs. Situations where a drive is allowed to coast to a stop or where the drive runs continuously with the torque limiter disengaging, are to be avoided. Longer life may also be achieved at lower torque settings. Drive Shutdown on Disengagement 0 Series MR The 0 Series MR is designed to run continuously in the disengaged condition. Protective Finish The standard phosphate and oil finish provides a high level of corrosion resistance. Units can be supplied with a suitable alternative finish for special machinery requirements, or for adverse environmental conditions. Please consult Rexnord to discuss any special requirements. 6
Maintenance and General Safety Information Maintenance The 0 Series uses sealed-for-life deep groove ball bearings. Other working surfaces are lightly greased on assembly. Under reasonably clean conditions the unit will operate with a minimum of maintenance and re-lubrication. It is recommended that the torque setting is checked and reset as part of routine maintenance or after any sustained period of disengaged running. The frequency of maintenance is dependent on many operating factors, but in adverse conditions, please consult Rexnord. General Safety Autogard Torque Limiters are reliable units, built to high standards of workmanship. Similar to all mechanical devices, each application must be considered on its own merits with reference to safety (i.e. lifting equipment, explosive conditions, etc). As rotating components, adequate guarding must be provided, in accordance with local codes. The intended use of torque limiters is for the protection of industrial machinery and should not be regarded as human safety devices. Rexnord staff is always available to discuss particular applications. 7
0 Series Industries Lumber Wood Products Energy Printing and Packaging Paper Converting Chemical Pharmaceuticals 8
Other Autogard Products Autogard Torque Limiter 00 Series Autogard Torque Limiter 400 Series Autogard Torque Limiter 600 Series Autogard Torque Limiter 80 Series Autogard Torque Limiter WT Series To learn more about the Autogard Torque Limiter offering and how it can provide you with high-quality overload protection, go to www.rexnord.com, where you ll find: Product information Brochures Manuals 866-REXNORD/866-79-667 (toll-free within the U.S.) or 44-64-66 (Outside the U.S.) 9
866-REXNORD/866-79-667 (Within the U.S.) 44-64-66 (Outside the U.S.) www.rexnord.com Why Choose Rexnord? When it comes to providing highly engineered products that improve productivity and efficiency for industrial applications worldwide, Rexnord is the most reliable in the industry. Commitment to customer satisfaction and superior value extend across every business function. Delivering Lowest Total Cost of Ownership The highest quality products are designed to help prevent equipment downtime and increase productivity and dependable operation. Valuable Expertise An extensive product offering is accompanied by global sales specialists, customer service and maintenance support teams, available anytime. Solutions to Enhance Ease of Doing Business Commitment to operational excellence ensures the right products at the right place at the right time. Rexnord Company Overview Rexnord is a growth-oriented, multi-platform industrial company with leading market shares and highly trusted brands that serve a diverse array of global end markets. Process & Motion Control The Rexnord Process & Motion Control platform designs, manufactures, markets and services specified, highly engineered mechanical components used within complex systems where our customers reliability requirements and the cost of failure or downtime are extremely high. Water Management The Rexnord Water Management platform designs, procures, manufactures and markets products that provide and enhance water quality, safety, flow control and conservation. 05 Rexnord TQ-004 06/5