PRODUCT GUIDE FT-DC-S DOCUMENT NUMBER REVISION DATE 0605 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
GETTING ED PAGE OF 0605 WELCOME Congratulations on the purchase of your FT-DC solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your FT-DC module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TABLE OF CONTENTS Box Contents 3 Tach Programming Procedure 4 Remote Programming Procedure 5 Valet Mode Programming Procedure 6 Compatible Accessories 7 Online Module Settings 9 Module Diagnostics 0 Remote Starter Error Codes Module Reset Procedure NEED HELP? 866 47-999 support@idatalink.com idatalink.com/support www.voltdata.com/forum www.facebook.com/groups/idatatech FT-DC-S
BOX CONTENTS - OF PAGE 3 OF 0605 BOX CONTENTS AUTOMATIC TRANSMISSION CUT LOOP M - PIN BLACK M3-0 PIN WHITE DRONE - 4 PIN GRAY RF PORT - 4 PIN BLUE M5-6 PIN BLUE M4-0 PIN BLACK PIN WHITE - LED PIN BLUE - THERMISTOR PROGRAMMING BUTTON 4 3 6 5 8 7 0 9 M 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 EMPTY 05 EMPTY 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 BROWN BLACK DOT - SIREN (+) OUTPUT 08 EMPTY 09 PURPLE/BLACK BLACK DOT - RAP SHUTDOWN (-) OUTPUT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT - GROUND WHEN ARMED (-) OUTPUT WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT LED FT-DAS - 4 PIN RED FT-DAS SENSITIVTY ADJUSTMENT DIAL WEBLINK PORT - 4 PIN BLACK LED 4 6 8 0 3 5 7 9 M3 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT 03 PURPLE SILVER DOT - DOOR (+) INPUT 04 GREEN SILVER DOT - DOOR (-) INPUT 05 EMPTY 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 EMPTY 0 TAN SILVER DOT - EXT ALARM SENSOR (-) INPUT M4 4 3 6 5 8 7 0 9 4 3 6 5 8 7 0 9 FUNCTIONS DEFINED BY FIRMWARE STICKERS HOOD SWITCH X M5 3 5 4 6 FUNCTIONS DEFINED BY FIRMWARE A omotive Data Solutions Inc. 06 FT-DC-S
CH PROGRAMMING PROCEDURE - OF PAGE 4 OF 0605 0 OFF ACC ON S ART vehicle for 5 seconds. 0 Press and hold the brake pedal. 03 Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for.5 seconds.) 04 Wait, LED will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed. FT-DC-S
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF PAGE 5 OF 0605 >> W ogram aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system. 06 Parking Light will flash once [x]. 0 Time restriction. Complete next step within 7 seconds. >> To program additional remotes: repeat steps 4 to 6 using each additional remote. 0 OFF ACC ON Cycle ignition ON ive times [5x OFF/ON] rapidly. 07 Wait, Parking Light will flash twice [x]. 03 Parking Light will flash once [x]. 08 OFF ACC ON Turn ignition to OFF position. 04 Time restriction. Complete next step within 5 seconds from previous step. 09 Aftermarket Remote Programming Procedure completed. 05 Press once [x] on LOCK button of aftermarket remote. FT-DC-S
VALET MODE PROGRAMMING PROCEDURE - OF PAGE 6 OF 0605 >> NTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 0 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to 5. 0 OFF ACC ON Cycle ignition ON twice [x OFF/ON] rapidly. 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [x] then will flash twice [x]. 05 OFF ACC ON Set ignition to OFF position. FT-DC-S
TIBLE ACCESSORIES - OF PAGE 7 OF 0605 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT 3 4 5 6 7 8 OBDII CONNECTOR 9 0 3 4 5 6 TELEMATIC KIT (accessory sold separately) DRONE MODULE TELEMATIC PORT (NC) FT-DC-S
TIBLE ACCESSORIES - OF PAGE 8 OF 0605 RF KIT (accessories sold separately) RF KIT MODULE RF PORT ANTENNA ALARM KIT (accessories sold separately) MODULE PIN BLACK 07 BROWN BLACK DOT - SIREN (+) OUTPUT RED BLACK SIREN MODULE PIN WHITE ALARM LED FT-DAS MODULE 4 PIN RED TEMPERATURE SENSOR (accessories sold separately) TEMPERATURE SENSOR MODULE PIN BLUE FT-DC-S
ONLINE MODULE SETTINGS - OF PAGE 9 OF 0605 WEB PROGRAMMABLE MENUS MENU Remote Starter MENU Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Coniguration (PTO) MENU 7 Input Conigurations MENU 8 Output Conigurations Programming options are avaible through Weblink and Weblink Mobile only. DESCRIPTION RS related coniguration options Convenience feature coniguration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by irmware/data/analog Set outputs for Auto by irmware/data/analog FT-DC-S
MODULE DIAGNOSTICS - OF PAGE 0 OF 0605 TEST MODULE LED STATUS DIAGNOSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE WITH IGNITION OFF Flashing RED Missing/wrong information from irmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. GREEN flash Tach signal programmed in Analog GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. FT-DC-S
REMOTE ER ERROR CODES - OF PAGE OF 0605 REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 0 E! "# $ 0 Key % & '% () *&+ % &$ 03 Door is open. 04 Trunk is open. 05 Foot brake is ON. 06 Hood is open. 07 The reservation is OFF. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Bypass problem. REMOTE ER SHUTDOWN ERROR CODES: NOTES [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a -WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 Emergency brake is lost. 03 Foot brake is ON. 04 Hood is open. 05 Engine RPM limiter is ON. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 0 Door is open. CAN communication failure during RS sequence. RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Takeover is not allowed. 4 Shutdown error, board overheat protection. FT-DC-S
MODULE RESET PROCEDURE - OF PAGE OF 0605 >> T,-.ollow/0 3ocedure resets the module programming to the vehicle. It does not reset any settings conigured online. 06 Module RESET completed. 0 Disconnect all connectors from module except the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. 07 Reconnect all connectors. 0 Disconnect the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. FT-DC-S
INSTALL GUIDE 06-07 ACURA ILX PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-HA7-[FT-DC-S] HARDWARE FT-DC-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE OF 8 B A T006_H 06-07 Acura ILX PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. VS SMART PCU, ABOVE GAS PEDAL (A) : 36 PIN PTS CONNECTOR LT BROWN : 36 PIN PTS HARNESS VS M 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT VS4 VS3 : 0 PIN IGNITION CONNECTOR GRAY : 0 PIN IGNITION HARNESS : BLUE HEADLAMP SWITCH (B) M3 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY LIGHTS OFF (-) ORANGE - 0 PARKING LIGHT (-) GRAY - 08 6 5 4 0 3 9 8 7 M4 0 0 03 04 05 06 07 08 09 0 3 4 5 6 7 8 9 0 MS HORN (-) HOOD SWITCH M5 0 0 03 04 05 06 MS 3 3 ONLY WITH T-HARNESS MANUFACTURED AFTER 06/03/7 T006_H INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 06-07 Acura ILX PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 B A T006_W 06-07 Acura ILX PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (+) BLUE -0 ACCESSORY (+) GRAY - 6 IGNITION (+) WHITE - 7 : GRAY SMART PCU, ABOVE GAS PEDAL (A) V (+) GREEN - 8 ER (+) YELLOW - 3 IGNITION (+) YELLOW - 34 87 6 5 4 3 0 9 8 7 6 5 4 3 36 35 34 333 3 30 9 8 7 6 5 4 3 0 9 GROUND (-) BROWN - 36 : GRAY M M3 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY CANH (DATA) PINK - 0 S-NET (DATA) GRAY - 05 CANL (DATA) BLUE - LIGHTS OFF (-) ORANGE - 0 PARKING LIGHT (-) GRAY - 08 0 9 8 7 6 5 4 3 0 9 8 7 6 5 4 3 : BLUE 6 5 4 3 0 9 8 7 HEADLAMP SWITCH (B) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK - S-NET (DATA) 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - V (+) INPUT 0 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - IGNITION (+) VEHICLE SIDE 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT - IGNITION (+) CONNECTOR SIDE 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH T006_W IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 06-07 Acura ILX PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 0 OFF ACC ON Set ignition to ON position. 07 OFF ACC ON Set ignition to ON position. Press and hold the brake pedal. 0 Wait, LED will flash GREEN rapidly. 08 Wait, LED will turn solid GREEN for seconds. 3 Press and release the module s programming button. 03 OFF ACC ON Set ignition to OFF position. 09 OFF ACC ON Set ignition to OFF position. 4 Release the brake pedal. 04 WARNING: Disconnect power last. Disconnect module from vehicle. 0 Press UNLOCK on the OEM remote. 5 Wait, LED will flash GREEN. 05 Connect module to computer and proceed with extended programming. >> If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 6 Module Programming Procedure completed. 06 Connect power first. Connect module to vehicle. OFF ACC ON vehicle for 5 seconds. 06-07 Acura ILX PTS AT
INSTALLATION CHECKLIST - OF PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. 06-07 Acura ILX PTS AT
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 06-07 Acura ILX PTS AT
INSTALL GUIDE 04-07 ACURA MDX PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-HA7-[FT-DC-S] HARDWARE FT-DC-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE OF 8 B A T003_H 04-07 Acura MDX PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. VS SMART PCU, ABOVE GLOVE BOX (A) : 36 PIN PTS CONNECTOR LT BROWN : 36 PIN PTS HARNESS VS M 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT VS4 VS3 : 0 PIN IGNITION CONNECTOR GRAY : 0 PIN IGNITION HARNESS : BLUE HEADLAMP SWITCH (B) M3 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY LIGHTS OFF (-) PINK - 0 PARKING LIGHT (-) GRAY - 08 6 5 4 0 3 9 8 7 M4 0 0 03 04 05 06 07 08 09 0 3 4 5 6 7 8 9 0 MS HORN (-) HOOD SWITCH M5 0 0 03 04 05 06 MS 3 3 ONLY WITH T-HARNESS MANUFACTURED AFTER 06/03/7 T003_H INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 04-07 Acura MDX PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 B A T003_W 04-07 Acura MDX PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (+) BLACK -0 ACCESSORY (+) BLUE - 6 IGNITION (+) PINK - 7 : GRAY SMART PCU, ABOVE GLOVE BOX (A) V (+) GREEN - 8 ER (+) LTBLUE - 3 IGNITION (+) YELLOW - 34 87 6 5 4 3 0 9 8 7 6 5 4 3 36 35 34 333 3 30 9 8 7 6 5 4 3 0 9 GROUND (-) BROWN - 36 : GRAY M M3 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY CANH (DATA) PINK - 0 S-NET (DATA) PURPLE - 05 CANL (DATA) LTBLUE - LIGHTS OFF (-) PINK - 0 PARKING LIGHT (-) GRAY - 08 0 9 8 7 6 5 4 3 0 9 8 7 6 5 4 3 : BLUE 6 5 4 3 0 9 8 7 HEADLAMP SWITCH (B) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK - S-NET (DATA) 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - V (+) INPUT 0 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - IGNITION (+) VEHICLE SIDE 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT - IGNITION (+) CONNECTOR SIDE 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH T003_W IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 04-07 Acura MDX PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 0 OFF ACC ON Set ignition to ON position. 07 OFF ACC ON Set ignition to ON position. Press and hold the brake pedal. 0 Wait, LED will flash GREEN rapidly. 08 Wait, LED will turn solid GREEN for seconds. 3 Press and release the module s programming button. 03 OFF ACC ON Set ignition to OFF position. 09 OFF ACC ON Set ignition to OFF position. 4 Release the brake pedal. 04 WARNING: Disconnect power last. Disconnect module from vehicle. 0 Press UNLOCK on the OEM remote. 5 Wait, LED will flash GREEN. 05 Connect module to computer and proceed with extended programming. >> If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 6 Module Programming Procedure completed. 06 Connect power first. Connect module to vehicle. OFF ACC ON vehicle for 5 seconds. 04-07 Acura MDX PTS AT
INSTALLATION CHECKLIST - OF PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. 04-07 Acura MDX PTS AT
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 04-07 Acura MDX PTS AT
INSTALL GUIDE 06-07 ACURA RDX PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-HA7-[FT-DC-S] HARDWARE FT-DC-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE OF 8 B A T007_H 06-07 Acura RDX PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. VS SMART PCU, ABOVE GAS PEDAL (A) : 36 PIN PTS CONNECTOR LT BROWN : 36 PIN PTS HARNESS VS M 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT VS4 VS3 : 0 PIN IGNITION CONNECTOR GRAY : 0 PIN IGNITION HARNESS : BLUE HEADLAMP SWITCH (B) M3 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY LIGHTS OFF (-) TAN - 0 PARKING LIGHT (-) GRAY - 08 6 5 4 0 3 9 8 7 M4 0 0 03 04 05 06 07 08 09 0 3 4 5 6 7 8 9 0 MS HORN (-) HOOD SWITCH M5 0 0 03 04 05 06 MS 3 3 ONLY WITH T-HARNESS MANUFACTURED AFTER 06/03/7 T007_H INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 06-07 Acura RDX PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 B A T007_W 06-07 Acura RDX PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (+) BLUE -0 ACCESSORY (+) GRAY - 6 IGNITION (+) PINK - 7 : GRAY SMART PCU, ABOVE GAS PEDAL (A) V (+) GREEN - 8 ER (+) GRAY - 3 IGNITION (+) YELLOW - 34 8 7 6 5 4 3 0 9 8 7 6 5 4 3 36 3534 333 3 30 9 8 7 6 5 4 3 0 9 GROUND (-) BLACK - 36 : GRAY M M3 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY CANH (DATA) PINK - 0 S-NET (DATA) LTGREEN - 05 CANL (DATA) BLUE - LIGHTS OFF (-) TAN - 0 PARKING LIGHT (-) GRAY - 08 0 9 8 7 6 5 4 3 0 9 8 7 6 5 4 3 : BLUE 6 5 4 3 0 9 8 7 HEADLAMP SWITCH (B) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK - S-NET (DATA) 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - V (+) INPUT 0 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - IGNITION (+) VEHICLE SIDE 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT - IGNITION (+) CONNECTOR SIDE 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH T007_W IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 06-07 Acura RDX PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 0 OFF ACC ON Set ignition to ON position. 07 OFF ACC ON Set ignition to ON position. Press and hold the brake pedal. 0 Wait, LED will flash GREEN rapidly. 08 Wait, LED will turn solid GREEN for seconds. 3 Press and release the module s programming button. 03 OFF ACC ON Set ignition to OFF position. 09 OFF ACC ON Set ignition to OFF position. 4 Release the brake pedal. 04 WARNING: Disconnect power last. Disconnect module from vehicle. 0 Press UNLOCK on the OEM remote. 5 Wait, LED will flash GREEN. 05 Connect module to computer and proceed with extended programming. >> If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 6 Module Programming Procedure completed. 06 Connect power first. Connect module to vehicle. OFF ACC ON vehicle for 5 seconds. 06-07 Acura RDX PTS AT
INSTALLATION CHECKLIST - OF PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. 06-07 Acura RDX PTS AT
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 06-07 Acura RDX PTS AT
INSTALL GUIDE 06-07 ACURA RLX PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-HA7-[FT-DC-S] HARDWARE FT-DC-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.
T-HARNESS / COMPONENT LOCATOR - OF PAGE OF 8 A B T008_H 06-07 Acura RLX PTS AT
T-HARNESS / WIRING DIAGRAM - OF PAGE 3 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. VS SMART PCU, NEAR DRIVER FUSEBOX (A) : 36 PIN PTS CONNECTOR LT BROWN : 36 PIN PTS HARNESS VS M 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT VS4 VS3 : 0 PIN IGNITION CONNECTOR GRAY : 0 PIN IGNITION HARNESS : BLUE HEADLAMP SWITCH (B) M3 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY LIGHTS OFF (-) RED - 0 PARKING LIGHT (-) PINK - 08 6 5 4 0 3 9 8 7 M4 0 0 03 04 05 06 07 08 09 0 3 4 5 6 7 8 9 0 MS HORN (-) HOOD SWITCH M5 0 0 03 04 05 06 MS 3 3 ONLY WITH T-HARNESS MANUFACTURED AFTER 06/03/7 T008_H INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 06-07 Acura RLX PTS AT
HARDWIRE / COMPONENT LOCATOR - OF PAGE 4 OF 8 B A T008_W 06-07 Acura RLX PTS AT
HARDWIRE / WIRING DIAGRAM - OF PAGE 5 OF 8! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSION ONLY PTS (+) GRAY -0 ACCESSORY (+) TAN - 6 IGNITION (+) BLUE - 7 : GRAY SMART PCU, NEAR DRIVER FUSEBOX (A) V (+) PINK - 8 ER (+) LTBLUE - 3 IGNITION (+) GREEN - 34 8 7 6 5 4 3 0 9 8 7 6 5 4 3 36 3534 333 3 30 9 8 7 6 5 4 3 0 9 GROUND (-) BROWN - 36 : GRAY M M3 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT - PARKING LIGHT (-) OUTPUT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY CANH (DATA) RED - 0 S-NET (DATA) RED - 05 CANL (DATA) WHITE - LIGHTS OFF (-) RED - 0 PARKING LIGHT (-) PINK - 08 0 9 8 7 6 5 4 3 0 9 8 7 6 5 4 3 : BLUE 6 5 4 3 0 9 8 7 HEADLAMP SWITCH (B) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW - PTS (+) OUTPUT 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE 5 BROWN - ACCESSORY (+) IN/OUT 6 ORANGE/BLACK - S-NET (DATA) 7 PINK - IGNITION (+) IN/OUT 8 PURPLE - ER (+) OUTPUT 9 RED - V (+) INPUT 0 BLACK - GROUND (-) M5 0 GRAY/BLACK BLUE DOT - IGNITION (+) VEHICLE SIDE 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT - IGNITION (+) CONNECTOR SIDE 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH T008_W IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE VEHICLE. INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 06-07 Acura RLX PTS AT
MODULE PROGRAMMING PROCEDURE - OF PAGE 6 OF 8 0 OFF ACC ON Set ignition to ON position. 07 OFF ACC ON Set ignition to ON position. Press and hold the brake pedal. 0 Wait, LED will flash GREEN rapidly. 08 Wait, LED will turn solid GREEN for seconds. 3 Press and release the module s programming button. 03 OFF ACC ON Set ignition to OFF position. 09 OFF ACC ON Set ignition to OFF position. 4 Release the brake pedal. 04 WARNING: Disconnect power last. Disconnect module from vehicle. 0 Press UNLOCK on the OEM remote. 5 Wait, LED will flash GREEN. 05 Connect module to computer and proceed with extended programming. >> If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 6 Module Programming Procedure completed. 06 Connect power first. Connect module to vehicle. OFF ACC ON vehicle for 5 seconds. 06-07 Acura RLX PTS AT
INSTALLATION CHECKLIST - OF PAGE 7 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [x] on the aftermarket keyfob. Question : Do the doors lock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call CHECKLIST - WITH AFTERMARKET KEYFOB 9 Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. 06-07 Acura RLX PTS AT
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? CHECKLIST - WITH OEM KEYFOB NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, afix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. 06-07 Acura RLX PTS AT
INSTALL GUIDE 05-07 ACURA TLX PTS AT DOCUMENT NUMBER REVISION DATE FIRMWARE FT-RSA-HA7-[FT-DC-S] HARDWARE FT-DC-S ACCESSORIES ADS-USB (OPTIONAL) ADS-WLM-AN/ADS-WLM-AP (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) COMPATIBLE RF-KIT (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certiied technician. Please review the Installation Guide carefully before beginning any work.