HANGERS, STRUT, AND FITTINGS SUBMITTAL

HANGERS, STRUT, AND FITTINGS SUBMITTAL Prepared By: Submitted by: Enter Company Name INTERNATIONAL SEISMIC APPLICATION TECHNOLOGY A Division of Tomarco Contractor Specialties Enter Project Name 4848 Northam Street, La Mirada, CA 9068 www.isatsb.com PLUMBING (SECTION 22 05 29) Spec Section (If different from above) Featuring Products Made in the USA services@isatsb.com Inside US: + 877 999 ISAT (4728) www.isatsb.com Outside US: + 00 74 880 024

Clevis Hangers Designed for the suspension of non-insulated stationary pipe lines. Fig. 450F has a layer of felt which separates the pipe from the hanger to reduce vibration and sound. The PVC coating on Fig. 45 protects the pipe from the metal surface of the hanger. APPROVALS: Underwriters' Laboratories Listed in the U.S. (UL) and Factory Mutual Approved for 2 / 2 " to 8" only. Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Low carbon steel Specify pipe size and figure number. Fig. 450, 450F, 45, 45 & 454 STANDARD CLEVIS HANGER Fig. 450 PLAIN Fig. 450F PLAIN WITH FELT LINING Fig. 45 ELECTRO-GALVANIZED Fig. 45 Fig. 454 PLAIN WITH PVC COATING HOT DIPPED GALVANIZED W/ELECTRO-GALVANIZED HARDWARE Note: When an over-sized clevis is used, a pipe spacer should be placed over the clevis bolt to prevent the lower U-strap from moving inward. D Adjustment (Top of cross bolt to bottom of hanger rod nut.) Pipe Rod Size Adjustment Max. Rec. Wt. Each Size A B C D E Cross Bolt Load/lbs. (in lbs.) / 2 / 8 2 7 / 6 2 7 / 8 / 8 2 / 4 70.24 / 4 / 8 2 5 / 8 / 8 / 4 2 / 6 / 4 70.24 / 8 / 6 / 4 5 / 8 2 5 / 8 / 4 70.28 / 4 / 8 / 8 4 / 6 5 / 8 2 5 / 6 / 4 70.2 / 2 / 8 / 2 4 7 / 6 / 2 / 6 / 4 70.40 2 / 8 / 4 5 5 / 8 5 / 6 / 4 70.52 2 / 2 / 2 4 5 / 8 6 / 6 2 4 / 6 / 8 50.72 / 2 4 7 / 8 6 5 / 8 / 6 4 / 4 / 8 50.78 / 2 / 2 4 / 2 6 / 2 / 4 7 / 8 / 8 50.6 4 5 / 8 5 / 2 7 / 6 / 4 4 / 6 / 8 40.5 5 5 / 8 6 / 8 9 / 8 7 / 8 5 5 / 6 / 2 40.88 6 / 4 6 7 / 8 0 / 8 5 / 8 6 / 2 940 2.76 8 / 4 8 / 4 2 7 / 8 2 / 8 7 7 / 8 5 / 8 2000 4.5 0 7 / 8 9 / 2 4 7 / 8 / 4 8 / 8 / 4 600 8. 2 7 / 8 5 / 8 8 2 / 2 0 / 2 / 4 800 0.05 4 2 / 4 9 / 4 2 5 / 8 / 4 7 / 8 4200 2.97 6 4 / 8 22 / 8 2 5 / 8 5 / 8 4600 20.85 8 / 8 6 / 2 25 / 2 / 2 5 / 8 4800 24.75 20 / 4 8 28 4 / 8 6 / 8 / 4 4800 42.45 24 / 4 20 / 4 2 / 4 4 / 4 8 / 8 / 4 4800 48.65 0 / 4 24 / 2 8 7 / 8 5 / 2 2 / 2 / 4 6000 69.8 6 / 2 2 50 8 / 4 0 / 2 9500 75.00 Note: Use of an upper locknut ensures proper performance. Pipe spacers provided on 0" and larger clevises. If ordering Fig. 450F felt lined hangers for pipe sizes of / 2 " or under, order the next largest size to allow for the thickness of the felt lining. 9

Clevis Hangers Fig. 450V PLASTIC PIPE CLEVIS HANGER Designed for the suspension of flexible plastic pipe lines. Used in conjunction with Fig. 450T. Low carbon steel Plain Specify size number and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. D Adjustment (Top of cross bolt to bottom of hanger rod nut.) Rod Size Pipe Size Adj. Cross Max. Rec. Wt. Each No. Size A B C D E Bolt Load/lbs. (in lbs.) / 2 / 8 4 / 4 5 / 2 5 / 8 4 5 / 6 / 4 50.8 / 4 / 8 4 9 / 6 5 / 2 5 / 8 4 / 8 / 4 50.8 / 8 4 / 8 5 / 2 5 / 8 5 / 6 / 4 50.8 / 4 / 8 4 / 8 5 / 2 5 / 8 / 6 / 4 50.8 / 2 / 8 4 5 / 2 5 / 8 9 / 6 / 4 50.8 2 / 8 / 6 5 / 2 5 / 8 / 4 / 4 50.8 2 2 / 2 5 / 8 6 5 / 8 8 / 4 / 4 5 / 6 / 8 50.5 2 5 / 8 6 / 6 8 / 4 / 4 5 / 8 / 8 50.5 2 / 2 5 / 8 5 / 6 8 / 4 / 4 5 / 8 50.5 2 4 5 / 8 5 7 / 6 8 / 4 / 4 4 5 / 8 / 8 50.5 Note: Use of an upper locknut ensures proper performance. Fig. 450T PLASTIC PIPE SUPPORT TROUGH Designed for use with Fig. 450V as a support for plastic or other flexible pipe systems. Hangers should be placed as close to the trough joints as possible. Low carbon steel Pre-galvanized Specify size number and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. 40 Size For Pipe Steel Trough Max. Rec. Wt. Each No. Sizes B Gauge Length Load/lbs. (in lbs.) / 2-2 / 2 8 ga. 0 ft. 50 5.40 2 2 / 2-4 8 ga. 0 ft. 50 0.75

Clevis Hangers Designed for the suspension of stationary insulated pipe lines. Fig. 455 is a combination of our Fig. 60 shield welded to a Fig. 450 clevis hanger which ensures that the shield will be installed in conjunction with the hanger. The shield is furnished with flared ends to prevent it from cutting into the insulation. Low carbon steel Plain low carbon steel clevis with pre-galvanized shield Specify size number and figure number. Fig. 455 CLEVIS WITH SECURED INSULATION SHIELD Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Size No. Rod Size A Shield I.D. Shield Length Shield Gauge Hanger Size Wt. Each (in lbs.) / 8 2 / 8 8 8 2.95 2 / 2 2 5 / 8 8 8 2 / 2.50 / 2 2 7 / 8 8 8 2 / 2.54 4 / 2 / 2 8 8.62 5 / 2 4 8 8 / 2.95 6 5 / 8 4 / 2 8 8 4 2.8 7 5 / 8 5 8 8 5 2.98 8 5 / 8 5 5 / 8 8 8 5.0 9 / 4 6 8 8 6.77 0 / 4 6 5 / 8 8 8 6.92 / 4 7 5 / 8 2 8 8 6. 2 / 4 8 5 / 8 2 8 8 6.66 7 / 8 9 5 / 8 2 8 0 0.84 4 7 / 8 0 / 4 2 8 0.7 5 7 / 8 / 4 2 8 2.9 6 7 / 8 2 / 4 2 8 2.65 7 4 2 8 4 6.9 8 5 2 8 6 25.08 9 6 2 8 6 25.20 20 / 8 7 2 8 8 29.55 2 / 8 8 2 8 8 29.8 22 / 4 9 2 8 20 47.8 24 / 4 2 2 8 24 5.7 Note: To determine proper size, consult shield selection guide on page 28. Use of an upper locknut ensures proper performance. 4

Pipe Roller Supports Fig. 460 PIPE ROLLER CHAIR Designed for supporting pipe in applications where horizontal movement, due to expansion and contraction, will occur but vertical adjustment is not necessary. The chair can be welded directly to the steel structure or secured in place through bolt holes. APPROVALS: Complies with Federal Specifications A-A-92A (Type 44) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 44). SIZING: Cast iron pipe roller with low carbon steel chair, axle and hex nuts. Plain Pipe roller size shown is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. Specify pipe roller size and figure number. Order mounting bolts separately. B Center of axle to center of pipe Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Recommended Pipe Bolt Size Roller (Not Included) Max. Rec. Wt. Each Size B C D E Load/lbs. (in lbs.) 2 5 / 8 / 2 / 4 / 8 X / 2 00.90 2 / 2 2 5 / 8 / 4 / 8 X / 2 600.9 2 / 4 / 4 2 / 8 X / 2 600.48 / 2 2 5 / 8 2 2 / 8 X / 2 600 2.44 4 2 / 4 2 / 4 2 / 2 X / 2 700 2.85 5 / 2 2 / 2 / 2 X / 2 700.75 6 4 2 / 4 / 4 / 2 X / 2 000 5.76 8 5 / 8 / 8 5 / 8 X / 2 00 8.0 0 6 / 8 5 / 8 5 / 4 5 / 8 X 2 700 2.28 2 7 / 2 4 / 8 5 / 2 5 / 8 X 2 200 20.54 4 8 / 8 4 / 6 6 / 2 / 4 X 2 00 25.6 6 9 / 2 5 / 8 8 / 4 / 4 X 2 / 2 900 7.8 8 0 / 2 6 9 / 4 / 4 X 2 / 2 4200 45.26 20 5 / 8 6 / 8 0 / 8 / 4 X 2 / 2 4500 52.5 24 4 7 / 4 2 / 4 7 / 8 X / 2 6000 88.00 42

Pipe Roller Supports Designed for suspending pipe in applications where horizontal movement, due to expansion and contraction, will occur and vertical adjustment is necessary. The knurled insert provided with Fig. 475 allows easier vertical adjustment. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). Cast iron pipe roller with low carbon steel frame, axle and hex nuts. Plain Fig. 470 & 475 PIPE ROLLER HANGER Fig. 470* WITHOUT SWIVEL Fig. 475 WITH ADJUSTING SWIVEL *Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. SIZING: Pipe roller size is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. Specify pipe roller size and figure number. Fig. 475 Available up to 8" Pipe Roller Size Fig. 475 B Center of axle to center of pipe Fig. 470 Pipe Roller Rod Size Adjustment Max. Rec. Wt. Each Size A B C D E F Load/lbs. (in lbs.) 2 / 8 5 / 8 2 5 / 8 / 6 4 / 8 50.05 2 / 2 / 2 2 2 / 8 / 6 5 / 4 225.29 / 2 2 / 4 / 2 / 4 6 / 8 7 / 8 0.56 / 2 / 2 2 5 / 8 / 4 / 4 7 4 / 8 90.8 4 5 / 8 2 / 4 5 / 6 / 6 7 / 2 5 475 2.8 5 5 / 8 / 2 4 5 / 6 9 / 6 8 5 / 8 6 685 4.42 6 / 4 4 5 / 8 2 / 6 0 / 4 7 / 8 780 5.98 8 / 4 5 / 8 6 / 2 2 / 6 2 / 4 9 / 4 780.42 0 7 / 8 6 / 8 7 / 8 2 5 / 4 965 7.6 2 7 / 8 7 / 2 8 / 4 2 / 8 7 / 8 / 4 200 24.62 4 8 / 8 9 2 8 7 / 8 4 / 4 200 6.00 6 9 / 2 9 / 4 / 4 20 / 4 6 7 / 8 200 44.00 8 0 / 2 / 4 2 / 4 2 / 4 8 7 / 8 400 54.00 20 / 4 5 / 8 2 / 2 2 / 2 26 20 7 / 8 600 74.00 24 / 2 / 6 6 / 2 4 / 2 25 600 26.00 Note: For Fig. 470 use of an upper locknut ensures proper performance. 4

Pipe Roller Supports Fig. 480 & 480D ADJUSTABLE PIPE ROLLER SUPPORT Fig. 480 Fig. 480D SINGLE PIPE ROLLER DOUBLE PIPE ROLLER Designed to support pipe in applications where horizontal movement, due to expansion and contraction, will occur and a vertical adjustment of up to 6 inches may be required. Fig. 480D is designed for supporting and guiding pipe where longitudinal movement and vertical adjustment are required. APPROVALS: Fig. 480 only, complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/ SP-69 and SP-58 (Type 4). Cast iron pipe roller and sockets with low carbon steel rods, axles and hex nuts. Plain Fig. 480 B Center of axle to center of pipe. Fig. 480D SIZING: Pipe roller size shown is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. Specify pipe roller size and figure number. Shipped with rods and nuts unassembled. Pipe Roller Rod Size E Max. Rec. Wt. Each (in lbs.) Size A B* C D 480 480D Load/lbs. 480 480D / 8 / 2 / 4 7 / 4 600.08 / 4 / 8 / 4 7 / 8 / 2 7 / 4 600.7 / 2 / 8 / 8 2 / 8 5 / 8 7 / 4 600.20 2 / 8 5 / 8 2 7 / 8 4 / 4 7 / 4 2 600.25.2 2 / 2 / 2 2 / 8 5 / 6 8 4 600 2.25 4.65 / 2 2 / 4 / 4 5 9 / 6 8 4 700 2.6 5.0 / 2 / 2 2 5 / 8 4 / 4 6 / 6 8 4 750 2.60 5.25 4 5 / 8 2 / 4 4 / 4 6 9 / 6 9 8 750.65 7.57 5 5 / 8 / 2 5 / 4 8 / 8 9 8 750 4.59 8.72 6 / 4 4 6 7 / 8 9 5 / 8 0 24 070 7.50 6.87 8 7 / 8 5 / 8 8 7 / 8 / 4 0 24 50.00 22.77 0 7 / 8 6 / 8 4 0 70.68 28.0 2 7 / 8 7 / 2 5 7 / 8 0 2400 9.0 8.7 4 8 / 8 4 / 8 7 / 4 2 6 0.20 64. 6 / 4 9 / 2 6 / 8 20 / 4 8 970 42.5 8 / 4 0 / 2 8 / 8 22 / 8 8 4200 46.50 20 / 4 5 / 8 20 / 8 24 / 2 8 4550 66.00 24 / 2 4 24 / 8 28 5 / 6 24 660 02.50 0 / 2 7 / 2 0 / 8 5 24 7290 86.80 *Due to the inconsistent dimensions associated with cast parts, please contact the factory if the "B" dimension is critical for installation. 44

Pipe Roller Supports SIZING: Designed to support pipe in applications where horizontal movement, due to expansion and contraction, will occur and a vertical adjustment is required. The roller assembly is attached by means of the threaded support rods and locked in place after correct alignment with the hex nuts provided. Cast iron pipe roller with low carbon steel rod with four hex nuts. Plain Pipe roller size shown is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. Specify pipe roller size and figure number. Fig. 48 ADJUSTABLE PIPE ROLLER SUPPORT B Center of axle to center of pipe. Pipe Roller Rod Size Max. Rec. Wt. Each Size A B C D E F Load/lbs. (in lbs.) 2 / 8 5 / 8 4 / 4 4 / 2 2 / 4 2 7 / 8 450.56 2 / 2 / 2 2 4 / 2 4 / 8 / 2 / 8 450.9 / 2 2 / 4 4 / 2 5 / 8 / 2 / 4 450.0 / 2 / 2 2 5 / 8 4 / 2 5 7 / 8 / 2 4 / 4 450.26 4 / 2 2 / 4 4 / 2 6 / 4 / 2 4 / 4 560.2 5 5 / 8 / 2 4 / 2 7 / 2 / 2 5 / 4 560 2.9 6 / 4 4 4 / 2 8 / 2 / 2 6 7 / 8 780.56 8 7 / 8 5 / 8 5 / 4 4 8 7 / 8 800 5.88 0 7 / 8 6 / 8 5 / 4 / 2 4 800 9.2 2 7 / 2 6 5 / 4 5 800 2.97 4 / 8 8 / 8 7 7 / 2 5 / 2 4 / 8 075 22.46 6 / 4 9 / 2 8 20 6 6 / 8 075 28.5 45

Pipe Roller Supports Fig. 486 PIPE ROLLER STAND Designed to support pipe in applications where horizontal movement, due to expansion and contraction, will occur. APPROVALS: Complies with Federal Specifications A-A-92A (Type 44) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 44). SIZING: Cast iron pipe roller with low carbon steel stand and axle. Plain Pipe roller size shown is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. The two cored holes G on roller sizes 2 thru 6 are on the outside of the stand. Specify pipe roller size and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Roller Size B C D E F G H J Max. Rec. Load/lbs. Wt. Each (in lbs.) 2 / 2 2 / 2 7 / 8 4 / 8 6 / 4 6 / 8 8 / 8 90 4.48 / 2 4 / 8 4 4 / 6 5 5 7 / 6 6 2 / 6 7 7 / 8 9 7 / 8 950 6.85 6 6 / 6 8 8 / 6 0 9 / 6 2 / 8 4 2 8 5 / 8 7 4 / 8 7 / 6 200 4.09 0 7 / 8 8 5 / 6 7 / 8 075 22.09 6 5 / 8 8 4 5 / 8 2 / 2 9 6 7 / 8 4 / 4 4980 2.00 20 5 5 / 8 24 7 / 4 / 2 9 7 5 / 8 4 / 8 600 4.4 0 2 7 / 8 7 2 0 5 / 8 7500 80.00 6 25 / 4 42 28 7 / 8 20 2 2 5 / 4 2000 25.00 46

Pipe Roller Supports Designed to support pipe in applications where horizontal movement, due to expansion and contraction, will occur and vertical adjustment is required. APPROVALS: Complies with Federal Specifications A-A-92A (Type 46) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 46). SIZING: Cast iron pipe roller and base with low carbon steel stand, axle and adjusting screws with locknuts. Plain Pipe roller size shown is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. Specify pipe roller size and figure number. Fig. 487 ADJUSTABLE PIPE ROLLER STAND WITH BASE Note: Refer to Fig. 486 for measurements of roller stand. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Roller Size B Min. Max. C D E Hole Size F G Bolt Size H Max. Rec. Load/lbs. Wt. Each (in lbs.) 2 5 / 8 5 / 8 2 / 2 5 / 8 5 5 / 8 5 / 4 6 7 / 8 7 5 / 2 5 / 8 90 2.0 / 2 6 6 / 4 4 6 / 2 7 5 7 7 / 2 5 / 8 8 / 8 5 / 4 5 / 8 950 5.24 6 7 5 / 8 8 / 8 8 0 / 8 5 / 8 0 / 2 2 / 4 2 4 / 4 4 5 / 8 4 7 / 8 7 / 8 0 / 4 6 / 4 / 8 / 4 200 0.59 9 / 2 / 8 8 / 8 7 / 8 075 44.96 6 5 / 4 6 5 / 8 8 6 / 8 7 / 4 / 8 4 / 2 8 5 / 8 / 8 4980 64.0 20 7 / 8 8 / 4 24 9 5 / 8 2 2 / 4 6 8 5 / 8 / 8 600 76.68 0 24 26 / 4 5 / 4 9 5 / 6 0 / 2 5 / 8 / 4 7500 42.25 6 2 / 6 29 / 6 42 29 / 4 2 / 4 6 22 / 2 5 / 8 / 2 2000 56.2 47

Pipe Roller Supports Fig. 490 PIPE ROLLER WITH SOCKETS Designed to suspend pipe in applications where horizontal movement, due to expansion and contraction, will occur. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). SIZING: Cast iron pipe roller and sockets with low carbon steel axle Plain Pipe roller size shown is for bare pipe. For proper sizing with insulation, refer to pipe roller selection guide on page 49, which is for use with pipe covering protection saddles. Specify pipe roller size and figure number. B Center of axle to center of pipe. Pipe Roller Size Rod Size A B* C Max. Rec. Load/lbs. Wt. Each (in lbs.) / 8 / 2 / 4 600.44 / 4 / 8 / 4 7 / 8 / 2 600.48 / 2 / 8 / 8 2 / 8 5 / 8 600.50 2 / 8 5 / 8 2 7 / 8 4 / 4 600.57 2 / 2 / 2 2 / 8 5 / 6 660.98 / 2 2 / 4 / 4 5 9 / 6 700.0 / 2 / 2 2 5 / 8 4 / 4 6 / 6 750.6 4 5 / 8 2 / 4 4 / 4 6 9 / 6 750.62 5 5 / 8 / 2 5 / 4 8 / 8 750 2.60 6 / 4 4 6 7 / 8 9 5 / 8 070 4.42 8 7 / 8 5 / 8 8 7 / 8 / 4 50 7.20 0 7 / 8 6 / 8 4 70 9.50 2 7 / 8 7 / 2 5 7 / 8 2400 6.00 4 8 / 8 4 / 8 7 / 4 0 24.20 6 / 4 9 / 2 6 / 8 20 / 4 970.75 8 / 4 0 / 2 8 / 8 22 / 8 4200 5.0 20 / 4 5 / 8 20 / 8 24 / 2 4550 47.00 24 / 2 4 24 / 8 28 5 / 6 660 76.20 0 / 2 7 / 2 0 / 8 5 7290 0.00 *Due to the inconsistent dimensions associated with cast parts, please contact the factory if the "B" dimension is critical for installation. D 48

Pipe Roller Selection Guide For use with pipe covering protection saddle figures 65-658 on pages 65-67. Pipe Roller Size Use With Fig. No. Pipe Insulation 460, 480 470 486 Size Thickness 48, 490 475 487 / 2 / 4 / 4 / 2 2 2 / 2 / 2 4 2 2 / 2 2 - / 2 / 2 / 2 2 - / 2 2 4 5 2 - / 2 2 / 2 4 2 2 / 2 2 - / 2 / 2 / 2 2 - / 2 2 4 5 2 - / 2 2 / 2 4 2 / 2 2 - / 2 / 2 4 2 - / 2 2 4 5 2 - / 2 2 / 2 4 2 / 2 2 - / 2 / 2 / 2 5 2 - / 2 2 4 5 2 - / 2 2 / 2 5 6 4-6 4 / 2 2 - / 2 / 2 / 2 5 2 - / 2 2 5 6 4-6 2 / 2 6 8 4-6 4 / 2 4 2 - / 2 / 2 4 5 2 - / 2 2 5 6 4-6 2 / 2 6 8 4-6 8 8 4-6 4 / 2 5 2 - / 2 / 2 5 6 4-6 2 6 8 4-6 2 / 2 8 8 4-6 8 0 4-6 4 4 5 2 - / 2 / 2 5 6 4-6 2 6 8 4-6 2 / 2 8 8 4-6 8 0 8-0 4 5 6 4-6 / 2 6 8 4-6 2 8 8 4-6 2 / 2 8 0 8-0 0 0 8-0 4 5 6 4-6 / 2 6 8 4-6 2 8 8 4-6 2 / 2 8 0 8-0 0 0 8-0 4 0 2 Pipe Roller Size Use With Fig. No. Pipe Insulation 460, 480 470 486 Size Thickness 48, 490 475 487 5 6 8 0 2 4 6 8 20 24 6 8 4-6 / 2 8 8 4-6 2 8 0 8-0 2 / 2 0 0 8-0 0 2 8-0 4 2 4 8-0 8 8 4-6 / 2 8 0 8-0 2 0 0 8-0 2 / 2 0 2 8-0 2 2 8-0 4 4 6 2-4 0 2 8-0 / 2 0 2 8-0 2 0 2 8-0 2 / 2 2 4 8-0 4 6 2-4 4 6 8 2-4 2 4 8-0 / 2 2 4 8-0 2 4 6 2-4 2 / 2 4 6 2-4 6 8 6-20 4 8 20 6-20 4 6 2-4 / 2 4 6 2-4 2 6 8 6-20 2 / 2 6 8 6-20 8 20 6-20 4 20 6-20 / 2 6 8 2-4 2 6 8 6-20 2 / 2 8 20 6-20 8 20 6-20 4 20 24 / 2 8 20 6-20 2 8 20 6-20 2 / 2 20 6-20 20 24 4 24 24 / 2 20 6-20 2 20 24 2 / 2 24 24 24 24 4 24 24 / 2 24 24 2 24 24 2 / 2 24 24 24 24 4 0 0 / 2 0 0 2 0 0 2 / 2 0 0 0 0 4 0 0 49

Pipe Roller Supports 50 Fig. 485 SHORT PIPE ROLLER Fig. 495 LONG PIPE ROLLER Fig. 496 ROLLER SOCKET Cast iron Plain Cast iron Plain Cast iron Plain Designed for supporting pipe in applications where horizontal movement, due to expansion and contraction, will occur. Specify pipe roller size and figure number. Pipe Roller Hole Size Max. Rec. Wt. Each Size B C D E Load/lbs. (in lbs.) 2 / 6 2 / 4 9 / 6 5 / 6 90.6 2 / 2 2 / 8 2 / 4 9 / 6 5 / 6 90.6 2 7 / 6 2 / 4 9 / 6 5 / 6 90.6 / 2 2 / 6 2 / 4 9 / 6 5 / 6 90.6 4 / 4 9 / 6 2 / 4 950.06 5 9 / 6 / 4 9 / 6 2 / 4 950.06 6 4 / 8 / 4 9 / 6 2 / 4 950.06 8 5 / 4 6 / 6 / 6 200 2.88 0 6 / 8 6 / 6 / 6 200 2.88 2 7 / 2 8 4 075 6.8 4 8 / 6 8 4 075 6.8 6 9 5 / 6 9 / 4 4 / 2 4980 9.25 8 0 / 8 9 / 4 4 / 2 4980 9.25 20 7 / 6 9 / 4 4 / 2 4980 9.25 24 7 / 6 0 / 2 4 / 8 600 0.6 0 6 9 / 6 2 / 4 7 / 8 5 / 6 7500 9.75 6 9 / 6 4 2 / 8 6 2000 4.06 42 22 / 4 4 2 / 8 6 2000 4.06 Designed for supporting pipe in applications where horizontal movement, due to expansion and contraction, will occur. Specify pipe roller size and figure number. Pipe Roller Size B C Hole Size D E Max. Rec. Load/lbs. Wt. Each (in lbs.) / 2 7 / 6 600.2 / 4 / 4 7 / 8 7 / 6 / 8 600.5 / 2 / 8 2 / 8 7 / 6 / 6 600.2 2 5 / 8 2 7 / 8 7 / 6 / 6 600.4 2 / 2 2 / 8 9 / 6 7 / 6 700.7 2 / 4 / 4 9 / 6 / 2 700.42 / 2 2 5 / 8 4 / 4 9 / 6 5 / 8 750.67 4 2 / 4 4 / 4 9 / 6 2 750.90 5 / 2 5 / 4 / 6 2 / 8 750.29 6 4 6 7 / 8 / 6 2 7 / 6 00.80 8 5 / 8 8 7 / 8 5 / 6 2 7 / 8 50.6 0 6 / 8 5 / 6 / 2 750 4.8 2 7 / 2 / 8 4 / 4 2400 9.0 4 8 / 8 4 / 8 / 4 4 5 / 8 00 2.2 6 9 / 2 6 / 8 / 8 4 7 / 8 4000 8.77 8 0 / 2 8 / 8 / 8 5 5 / 6 4200 2.97 20 5 / 8 20 / 8 / 8 6 / 6 4550 22.5 24 4 24 / 8 5 / 8 7 / 6 600 42.00 0 7 / 2 0 / 8 7 / 8 9 / 6 700 98.00 Designed for use with Fig. 495. Specify socket number and figure number. Socket Number Rod Size A Use With Pipe Roller Size Axle Size B C D Wt. Each (in lbs.) / 8 to 2 / 8 5 / 8 / 6.2 2 / 2 2 / 2 to / 2 / 2 / 4 / 4 / 6.27 2A 5 / 8 4 / 2 7 / 8 / 4 / 6.25 5 / 8 5 5 / 8 9 / 6.5 4 / 4 6 / 4 / 4 / 6 / 8.92 5 7 / 8 8 to 0 7 / 8 / 4 2 / 8 / 8.44 6 7 / 8 2 / 8 2 / 4 / 8.4 7 4 / 8 / 4 2 / 8 / 8 2.0 8 / 4 6 to 20 / 4 / 6 5 / 8 2.56 9B / 2 24 / 2 2 / 6 / 8 2 / 6 4.96 0 / 2 0 / 4 2 9 / 2 4 2 5 / 6 6.94

Split Ring Hangers Designed for the suspension of non-insulated stationary pipe lines. The hinged design allows for ease of placement even after pipe is already in place. Can be used in conjunction with Fig. 44 turnbuckle adjuster. APPROVALS: Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Specify pipe size and figure number. Fig. 500 SPLIT RING HANGER Pipe Size B Bolt Size Max. Rec. Load/lbs. Wt. Each (in lbs.) / 8 / 4 / 4 X 200.07 / 2 5 / 6 / 4 X 200.08 / 4 / 8 / 4 X 00. / 4 / 4 X 00.2 / 4 9 / 6 / 4 X 00.7 / 2 / 6 / 4 X / 4 00.20 2 2 / 6 / 4 X / 4 00.2 2 / 2 2 / 4 / 4 X / 4 450.4 2 / 4 / 4 X / 4 450.67 / 2 / 8 / 4 X / 4 450.86 4 5 / 8 / 8 X 2 520.9 5 4 / 2 / 8 X 2 520.52 6 5 7 / 6 / 2 X 2 00 2.64 8 6 / 8 / 2 X 2 800.84 Malleable iron Plain Designed for the suspension of non-insulated stationary copper tubing. The hinged design allows for ease of placement even after tubing is already in place. Can be used in conjunction with Fig. 44C turnbuckle adjuster. APPROVALS: Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Specify tube size and figure number. Fig. 502 COPPER TUBING SPLIT RING HANGER Tube Size B Bolt Size Max. Rec. Load/lbs. Wt. Each (in lbs.) / 2 / 4 / 4 X 200.08 / 4 7 / 8 / 4 X 00.0 / 8 / 4 X 00.2 / 4 / 4 / 4 X 00.4 / 2 / 8 / 4 X 0.8 2 / 6 / 4 X 00.26 2 / 2 5 / 6 / 4 X / 4 450.8 2 / 4 / 4 X / 4 450.49 / 2 2 5 / 8 / 4 X / 4 450.64 4 2 5 / 6 / 4 X / 4 520.88 Malleable iron Copper Color Epoxy Finish 5

Split Ring Hangers Fig. 505 ADJUSTABLE SPLIT RING SWIVEL HANGER Designed for the suspension of non-insulated stationary pipe lines. The hinged design allows for ease of placement even after the hanger is in place. The adjustable swivel allows for vertical adjustment after pipe is in place. APPROVALS: Complies with Federal Specifications A-A-92A (Type 6) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 6). Malleable iron Plain Specify pipe size and figure number. Pipe Rod Size Max. Rec. Wt. Each Size A B C D E F G Load/lbs. (in lbs.) / 4 / 8 2 5 / 8 2 / 8 5 / 6 / 8 00.2 / 8 2 5 / 6 / 8 7 / 6 00.25 / 4 / 8 / 8 2 9 / 6 / 8 9 / 6 00.0 / 2 / 8 / 4 2 / 4 9 / 6 5 / 8 00.2 2 / 8 4 / 4 / 6 7 / 8 / 6 00.4 2 / 2 / 2 5 / 4 4 5 / 6 2 / 8 9 / 6 500.65 / 2 6 / 8 4 5 / 8 2 / 8 7 / 8 500.78 / 2 / 2 7 5 2 / 4 4 / 4 500.85 4 5 / 8 8 / 4 6 2 7 / 8 5 / 4 900.54 5 5 / 8 9 / 2 6 / 4 5 7 / 8 900 2.00 6 / 4 7 / 6 / 8 6 / 6 00.20 8 7 / 8 4 9 / 6 4 / 8 8 9 / 6 800 5.00 Note: Sizes / 4 to 2 do not have a window cutout. 52 Fig. 508 & 508R HINGED EXTENSION SPLIT CLAMP Fig. 508 Fig. 508R PIPE THREAD BOLT THREAD Designed for non-insulated stationary pipe lines in either a horizontal or vertical position. The hinged design allows for a quick installation. APPROVALS: Complies with Federal Specifications A-A-92A (Type 2) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 2). Malleable iron Plain or Electro-galvanized Specify pipe size, finish and figure number. A Pipe Pipe Thread Bolt Thread Max. Rec. Wt. Each Size Fig. 508 Fig. 508R B Load/lbs. (in lbs.) / 8 / 4 / 8 / 6 80. / 2 / 4 / 8 7 / 8 80.4 / 4 / 4 / 8 80.6 / 4 / 8 / 8 80.8 / 4 / 4 / 8 5 / 6 80.22 / 2 / 4 / 8 7 / 6 80.8 2 / 4 / 8 / 6 80.44 2 / 2 / 2 / 2 2 / 8 00.45 / 2 / 2 2 7 / 6 00.55 4 / 2 / 2 00.95

Split Ring Hangers Designed for non-insulated stationary pipe lines in either a horizontal or vertical position. APPROVALS: Complies with Federal Specification A-A-92A (Type 2) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 2). Malleable iron Plain or Electro-galvanized Specify pipe size, finish and figure number. Fig. 50 & 50R EXTENSION SPLIT CLAMP Fig. 50 Fig. 50R PIPE THREAD BOLT THREAD A Pipe Size / 8 Pipe Thread Fig. 50 / 4 Bolt Thread Fig. 50R / 8 B / 6 Max. Rec. Load/lbs. 80 Wt. Each (in lbs.). / 2 / 4 / 8 7 / 8 80.4 / 4 / 4 / 8 80.6 / 4 / 8 / 8 80.8 / 4 / 4 / 8 5 / 6 80.22 / 2 / 4 / 8 7 / 6 80.8 2 / 4 / 8 / 6 80.44 2 / 2 / 2 / 2 2 / 8 00.45 / 2 / 2 2 7 / 6 00.55 4 / 2 / 2 / 2 00.70 Designed for non-insulated stationary tubing lines in either a horizontal or vertical position. The hinged design of Fig. 52H allows for a quicker installation. APPROVALS: Complies with Federal Specification A-A-92A (Type 2) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 2). Tube Size Malleable iron Copper color epoxy finish Specify tube size and figure number. Rod Size A B Max. Rec. Wt. Each (in lbs.) Load/lbs. Fig. 52 Fig. 52H / 8 / 8 9 / 6 80.07.08 / 2 / 8 / 6 80.09.09 / 4 / 8 7 / 8 80.09.2 / 8 80.0. / 4 / 8 / 8 80.2.5 / 2 / 8 5 / 6 80..20 2 / 8 / 2 80.8.25 2 / 2 / 2 7 / 8 00.65.45 / 2 2 / 8 00.00.55 4 / 2 2 / 4 00.40.90 Fig. 52 & 52H COPPER TUBING EXTENSION SPLIT CLAMP Fig. 52 Fig. 52H TWO PIECE DESIGN HINGED DESIGN Fig. 52H shown 5

Pipe Clamps Fig. 520* Fig. 52 Fig. 520 & 52 STANDARD PIPE CLAMP PLAIN ELECTRO-GALVANIZED Designed to be used in the suspension of non-insulated pipe lines. Normally used in conjunction with Fig. 5 weldless eye nut, Fig. 50 eye rod or Fig. 55 welded eye rod to allow flexibility at the rod attachment. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). Low carbon steel Specify pipe size and figure number. *Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Size B C / 2 / 8 9 / 6 / 6 / 8 / 4 / 8 / 4 / 4 / 8 / 8 7 / 8 / 8 / 8 / 4 / 8 2 / 8 5 / 8 / 8 / 2 / 8 2 / 4 / 4 / 8 2 / 2 2 9 / 6 2 / 6 / 2 2 / 2 5 / 8 / 8 2 5 / 8 / 2 5 / 8 5 / 6 2 / 6 / 2 / 2 5 / 8 / 2 / 6 / 2 4 / 4 4 / 8 / 8 5 / 8 5 / 4 4 / 4 4 / 8 5 / 8 6 7 / 8 5 7 / 8 4 7 / 8 / 4 8 7 6 / 4 0 8 / 6 7 9 / 6 7 / 8 2 9 7 / 8 8 7 / 8 7 / 8 4 / 8 5 / 6 9 5 / 6 7 / 8 6 / 8 2 5 / 8 0 7 / 8 7 / 8 8 / 4 / 8 5 / 8 20 / 8 4 5 / 6 2 9 / 6 / 8 24 5 / 8 7 / 2 5 / 2 / 4 0 2 20 7 / 8 8 5 / 8 / 2 D Bolt Size Max. Rec. Load/lbs. 650 F 750 F Wt. Each (in lbs.) 500 445. 500 445.5 500 445.9 500 445.40 800 75.45 040 90.90 040 90.0 040 90.20 040 90.25 040 90.85 040 90 2.05 65 440 5.06 65 440 6.08 2490 2220 2.8 2490 2220.08 2490 2220 6.70 2490 2220 2.9 060 270.2 060 270 8.66 060 270 52.27 4000 520 05. 54

Pipe Clamps Designed to be used in the suspension of non-insulated pipe lines where heavier loads are to be suspended. Normally used in conjunction with Fig. 5 weldless eye nut or Fig. 55 welded eye rod to allow flexibility at the rod attachment. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). Fig. 522 HEAVY DUTY PIPE CLAMP Low carbon steel. Plain Specify pipe size and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Bolt Size B C D Size 4 / 8 / 4 / 2 4 / 8 / 4 / 4 4 4 5 / 6 / 6 7 / 8 5 5 9 / 6 4 5 / 6 7 / 8 6 / 8 6 / 6 5 / 6 8 / 8 8 / 4 6 / 4 0 / 4 9 7 / 8 7 7 / 8 / 4 2 5 / 8 7 / 8 9 / 2 / 2 4 5 / 8 2 / 4 0 / 8 / 2 6 5 / 8 5 / 6 / 6 / 2 8 5 / 8 5 / 4 2 / 6 / 2 20 5 / 8 5 / 6 5 / 6 / 2 24 / 4 7 / 4 5 / 8 / 2 Max. Rec. Load/lbs. Wt. Each 650 F 750 F (in lbs.) 70 005 4.96 70 005 5.6 55 5 5.74 55 5 7. 4865 440.48 4865 440 5.78 600 560 24.20 8675 7740 4.54 920 85 5.25 920 85 56.5 950 860 70.2 950 860 74.68 9200 8205 26.29 Note: Larger sizes available upon request. 55

Pipe Clamps Fig. 525 DOUBLE BOLT PIPE CLAMP Designed for the suspension of high temperature insulated pipe lines. Normally used in conjunction with Fig. 5 weldless eye nut or Fig. 55 welded eye rod to allow flexibility at the rod attachment. The clamp can be used with up to 4 inches of insulation and temperatures up to 750 F. APPROVALS: Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Low carbon steel Plain or Electro-galvanized Specify pipe size, finish and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Max. Rec. Bolt Size Load/lbs. Pipe Wt. Each Size B C D E F G H 650 F 750 F (in lbs.) / 4 5 / 8 7 / 6 2 / 6 2 / 8 / 8 / 8 950 850.8 5 / 8 / 2 2 7 / 8 2 / 8 / 8 / 8 950 850.02 / 4 5 / 8 9 / 6 2 5 / 6 2 / 6 7 / 6 / 8 / 8 950 850.07 / 2 5 / 4 4 5 / 8 2 5 / 8 2 5 / 8 / 2 545 80 2.0 2 5 / 8 4 / 4 2 / 4 2 / 8 5 / 8 / 2 545 80 2.60 2 / 2 5 / 6 5 / 6 / 6 2 7 / 6 5 / 8 / 2 545 80 2.7 6 5 / 8 / 8 2 / 4 5 / 8 / 2 545 80.0 / 2 6 5 / 6 5 / 6 / 6 / 6 5 / 8 / 2 545 80.28 4 8 / 6 7 / 6 5 / 6 4 / 6 / 4 5 / 8 2500 220 6.67 5 8 5 / 8 7 5 / 8 5 5 / 8 4 5 / 8 / 4 5 / 8 2500 220 7.05 6 / 2 9 7 / 8 8 5 / 8 6 / 8 5 / 8 7 / 8 / 4 2865 2555.45 8 / 2 / 8 9 7 / 8 7 5 / 8 6 / 8 7 / 8 / 4 2865 2555.5 0 / 2 2 / 8 / 8 8 7 / 8 7 5 / 8 7 / 8 240 2890 9.80 2 / 2 / 4 2 / 2 0 / 4 9 7 / 8 240 2890 22.25 4 / 2 5 / 6 9 / 6 7 / 6 9 5 / 6 / 4 7 / 8 400 85 7.68 6 / 2 5 / 6 4 5 / 6 2 / 6 0 / 6 / 4 7 / 8 400 85 4.40 8 / 2 6 / 6 5 7 / 6 5 / 6 / 6 / 4 400 85 44.87 20 2 8 6 / 2 4 / 2 / 8 / 8 5490 4900 57.25 24 2 20 / 4 8 / 4 6 / 4 5 / 4 / 8 / 4 4500 405 65.90 Note: Larger sizes available upon request. 56

Pipe Clamps Designed for the suspension of high temperature pipe lines. The increased material and bolt sizes allow Fig. 526 to be used in applications where heavier loads will be encountered. Normally used in conjunction with Fig. 5 weldless eye nut or Fig. 55 welded eye rod to allow flexibility at the rod attachment. The clamp can be used with up to 4 inches of insulation and temperatures up to 750 F. Fig. 526 HEAVY DUTY DOUBLE BOLT PIPE CLAMP APPROVALS: Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Low carbon steel Plain Specify pipe size and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Max. Rec. Pipe Bolt Size Load/lbs. Size B C D E F G H 650 F 750 F 6 / 4 / 8 8 7 / 8 6 / 6 4 / 6 7 / 8 8 2 / 6 9 5 / 6 7 7 / 6 6 / 6 / 8 0 2 / 4 2 5 / 6 / 6 9 / 6 7 7 / 6 / 4 / 8 2 2 / 2 4 2 / 4 0 / 6 8 5 / 6 / 2 / 4 4 2 / 2 5 / 8 / 6 2 0 / 2 / 4 6 6 / 6 4 9 / 6 7 / 6 / 6 / 4 / 2 8 / 2 8 / 6 6 5 / 6 5 5 / 6 2 / 6 2 / 4 20 / 2 9 5 / 6 7 7 / 6 6 7 / 6 5 / 6 2 / 4 24 / 2 22 / 2 9 / 2 9 6 2 / 4 Note: Larger sizes available upon request. Wt. Each (in lbs.) 500 25 4.4 4800 4285 20.99 5500 490.7 7000 6250 48.7 9500 8485 70.50 0000 890 9.90 800 225 2.72 500 665 56.4 600 4555 204.65 57

Pipe Clamps Fig. 55 OFFSET PIPE CLAMP Designed to be used in the clamping of pipe lines at a fixed distance away from the floor or wall. Low carbon steel Plain Specify pipe size and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Bolt Max. Rec. Wt. Each Size B C D Size Load/lbs. (in lbs.) / 4 5 7 / 8 2 / 2 7 / 6 / 8 90.87 6 2 5 / 8 7 / 6 / 8 90.92 / 4 6 / 2 2 / 4 7 / 6 / 8 90.5 / 2 6 9 / 6 7 / 6 / 8 90.24 2 7 / 6 / 6 7 / 6 / 8 420.56 2 / 2 8 / 8 7 / 6 7 / 6 / 8 420.78 8 / 6 / 2 7 / 6 / 8 420.98 / 2 9 / 4 4 7 / 6 / 8 420 2.45 4 4 / 4 9 / 6 / 2 60.00 5 2 / 8 4 / 4 9 / 6 / 2 60.50 6 4 / 8 5 5 / 6 9 / 6 / 2 870 6.50 8 6 / 2 6 5 / 6 9 / 6 / 2 870 7.90 0 9 / 8 7 / 4 / 6 5 / 8 870 2.70 2 25 / 2 8 7 / 8 / 6 5 / 8 870 2.20 Fig. 545 EXTENDED PIPE CLAMP Designed to be used in the suspension or support of pipe lines where exact distance between the structure and the pipe is unknown until time of installation. Low carbon steel Plain Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. 58 Pipe Size Specify pipe size and figure number. Bolt B C Size / 4 4 / 6 2 / 8.82 4 5 / 6 2 / 8 2.25 / 4 4 / 6 2 / 8 2.9 / 2 4 5 / 6 2 / 8 2.44 2 5 5 / 6 2 / 8.9 2 / 2 6 9 / 6 2 / 8.4 7 / 6 2 / 8.54 4 8 5 / 6 2 / 2 4.75 5 0 / 8 2 / 2 5.8 6 2 / 6 2 / 2 8.8 8 4 / 8 2 / 2 9.25 Wt. Each (in lbs.)

Riser Clamps Designed for supporting and stabilizing vertical pipe runs. The PVC coating on Fig. 55 protects the pipe from the metal surface of the clamp. This product is not intended for use with hanger rods. Clamp is designed for standard iron pipe O.D. and must be considered when sizing other types of piping. APPROVALS: Underwriters' Laboratories Listed in the U.S. (UL) and Factory Mutual Approved for sizes / 4 " to 8" only. Complies with Federal Specifications A-A-92A (Type 8) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 8). Fig. 550* Fig. 55 Fig. 55 Fig. 550, 55 & 55 RISER CLAMP PLAIN ELECTRO-GALVANIZED PLAIN WITH PVC COATING Low carbon steel Specify pipe size and figure number. *Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Size B Bolt Size Max. Rec. Load/lbs. Wt. Each (in lbs.) / 2 9 / 8 X / 4 220.05 / 4 8 7 / 8 / 8 X / 4 220.05 8 / 4 / 8 X / 4 220.05 / 4 9 / 4 / 8 X / 4 250.0 / 2 0 / 8 X / 4 250.7 2 0 / 4 / 8 X / 4 00.20 2 / 2 / 8 / 8 X / 2 400.89 / 4 / 8 X / 2 500.99 / 2 2 / 2 / 8 X / 2 600 2.7 4 / 2 X / 4 750 2.2 5 4 / 4 / 2 X / 4 500.24 6 5 / 8 / 2 X / 4 600.89 8 8 / 2 5 / 8 X 2 2500 7.60 0 20 / 2 5 / 8 X 2 2500.0 2 22 / 2 5 / 8 X 2 / 2 2700 6.50 4 25 / 8 5 / 8 X 2700 7.70 6 26 / 4 / 4 X / 2 2900 0.40 8 27 7 / 8 / 4 X / 2 2900.0 20 0 / 4 X / 2 2900 6.0 24 5 7 / 8 X / 2 2900 48.68 0 42 / 8 7 / 8 X / 2 2900 60.6 Installation practice for Model 550 Riser Clamps When possible the clamp should be placed under a coupling, hub or welded lugs on steel pipe. Bolt torques should be per industry standards. Recommended Torque For Pipe Clamp Hardware / 4 "-20 5 / 6 "-8 / 8 "-6 / 2 "- 5 / 8 "- / 4 "-0 & Larger 6 ft/lbs ft/lbs 9 ft/lbs 50 ft/lbs 65 ft/lbs 75 ft/lbs 59

Riser Clamps Fig. 552 & 554 COPPER TUBING RISER CLAMP Fig. 552* COPPER COLOR EPOXY FINISH Fig. 554 COPPER COLOR EPOXY FINISH WITH PVC COATING Designed for supporting and stabilizing vertical tubing runs. The PVC coating on Fig. 554 protects the tube from the metal surface of the clamp. APPROVALS: Complies with Federal Specifications A-A-92A (Type 8) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 8). Low carbon steel *Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Specify tube size and figure number. Tube Max. Rec. Wt. Each Size B Bolt Size Load/lbs. (in lbs.) / 2 6 / 6 / 4 75.50 / 4 7 / 4 75.52 8 / 4 / 4 20.64 / 4 9 / 4 50.65 / 2 9 / 8 / 4 50.70 2 9 5 / 6 / 8 50.98 2 / 2 0 / 2 / 8 00.09 / 8 00.7 / 2 2 / 6 / 8 00.5 4 2 5 / 8 / 8 00.67 5 4 / 8 / 2 500 2.42 6 5 / 2 500 2.68 Recommended Torque For Pipe Clamp Hardware / 4 "-20 5 / 6 "-8 / 8 "-6 / 2 "- 5 / 8 "- / 4 "-0 & Larger 6 ft/lbs ft/lbs 9 ft/lbs 50 ft/lbs 65 ft/lbs 75 ft/lbs 60

Underground Pipe Clamps Note: Designed for clamping the caulked joints of underground A.W.W.A. ductile iron water pipes to prevent separation of joints. Low carbon steel Plain Specify pipe size and figure number. Order Fig. 585 washer separately. Pipe Max. Pipe Bolt Size Recom. Tie Rod Wt. Each Size O.D. B C D E Size (in lbs.).96 / 4 9 / 4 5 / 8 X / 4 6.8 4 4.80 0 / 4 / 4 5 / 8 X / 4 8.80 6 6.90 4 7 / 8 2 / 4 5 / 8 X / 4 0.50 8 9.05 7 / 4 4 / 2 / 4 5 / 8 X / 4 2.4 0.0 9 / 2 6 / 4 / 4 5 / 8 X / 4 4.80 2.20 2 / 4 9 / 4 5 / 8 X / 2 / 4 6.0 4 5.0 27 7 / 8 2 / 8 / 8 7 / 8 X 4 4 44.7 6 7.40 29 / 8 25 / 2 / 2 X 4 / 2 / 8 64.74 8 9.50 2 / 4 28 / 2 / 4 X 4 / 2 / 4 7.69 20 2.60 / 4 29 / 4 5 / 8 / 4 X 4 / 2 / 8 86.00 24 25.80 7 / 4 4 / 4 / 2 X 5 / 2.00 0 2.00 45 / 8 4 / 8 2 / 2 X 5 / 2 / 4 6.78 6 8.0 50 / 4 46 / 2 2 / 2 / 2 X 5 / 4 55.50 Clamps must be connected by means of threaded tie rods and the nuts drawn tight on the washers to assure a tight joint. Fig. 580 TWO BOLT UNDERGROUND PIPE CLAMP Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Typical Installation Designed to secure tie rods when used in conjunction with Fig. 580 two bolt underground pipe clamp. Low carbon steel. Cast Iron ( / 4 " Tie Rod Only) Fig. 585 WASHER For Fig. 580 Plain Specify tie rod size and figure number. Tie Rod Size Dia. B C D E For Pipe Wt. Each Sizes (in lbs.) / 4 7 / 8 5 / 8 / 4 2 5 / 6-2.80 / 8 5 / 8 7 / 8 / 6 4.45 / 8 / 4 5 / 8 4 6 2. / 4 / 8 5 / 8 4 8 2.26 / 8 / 2 / 4 4 20 2.87 / 2 5 / 8 / 4 4 24 2.7 / 4 7 / 8 4 0-6 4.7 Available in stainless steel except for / 4 " tie rod. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Note: Tie rod size 4 " made of cast iron material. 6

Underground Pipe Clamps Fig. 590 FOUR BOLT UNDERGROUND PIPE CLAMP Designed for clamping the caulked joints of underground A.W.W.A. ductile iron water pipe lines to prevent separation of joints. APPROVALS: Complies with National Fire Protection Association Standard 24 for 4" thru 2" pipe Low carbon steel Plain Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Specify pipe size and figure number. Order Fig. 595 washer separately. Recom. Max. Force Max. Bolt Tie Test On Pipe Pipe Size Rod Pressure Clamp Wt. Each Size O.D. B C D E Size P.S.I. (in lbs.) (in lbs.).96 / 8 9 / 8 / 4 5 / 8 X / 4 250 4550 8.60 4 4.80 4 / 2 0 / 8 / 4 5 / 8 X / 4 250 4550 9.8 6 6.90 7 2 5 / 8 / 4 5 / 8 X / 4 250 940.50 8 9.05 9 / 8 5 / 8 / 4 5 / 8 X / 2 / 4 250 6080 20.54 0.0 22 7 / 8 / 4 / 4 X / 2 / 4 250 2480 2.5 2.20 25 5 / 8 20 / 2 / 4 7 / 8 X / 2 250 420 5.85 4 5.0 27 / 4 2 / 8 / 4 7 / 8 X 4 20 22200 46.78 6 7.40 7 / 8 25 7 / 8 / 4 X 4 / 8 5 27760 70.5 8 9.50 5 5 / 8 29 / 4 / 4 X 4 / 2 / 4 00 2900 84.65 20 2.60 8 / 8 / 8 / 4 / 4 X 4 / 2 / 8 75 27500 98.65 24 25.80 44 / 2 6 / 2 / 4 / 2 X 5 / 2 50 26200 5.50 Typical Installation Note: Clamps must be connected by means of threaded tie rods and the nuts drawn tight on the washers to assure a tight joint. Fig. 595 WASHER For Fig. 590 Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed to secure tie rods when used in conjunction with Fig. 590 four bolt underground pipe clamp. Low carbon steel Plain Specify tie rod size and figure number. Tie Rod Size Dia. B C D For Pipe Sizes Wt. Each (in lbs.) / 4 7 / 8 / 2-0.9 / 8 / 2 / 2 2-4.49 / 8 / 4 5 / 8 / 2 6.57 / 4 / 8 / 4 / 2 8 2.5 / 8 / 2 / 4 / 2 20.92 / 2 5 / 8 / 4 / 2 24.85 62

Center Load Beam Clamps Designed to be used in the suspension of a hanger rod from the center of an I-beam. The clamp s design allows the load to be distributed equally on either side of the beam. Normally used in conjunction with Fig. 50 eye rod, Fig. 55 welded eye rod or Fig. 5 weldless eye nut. APPROVALS: Complies with Federal Specifications A-A-92A (Type 2) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 2). Specify type number, width of flange and figure number. Type Bolt Max. Rec. No. B C Size Load/lbs. / 2 / 2 / 8 000 2 / 2 / 2 / 2 250 5 / 8 / 2 / 2 500 Fig. 60 STANDARD DUTY CENTER LOAD BEAM CLAMP Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Flange Max. Flange Wt. Each (in lbs.) Width Thickness Type Type 2 Type 7 / 6.85 4 / 2.88.0.6 5 5 / 8.0.28 2.06 6 / 4..44 2.2 7 7 / 8.2.57 2.47 8 7 / 8.25.66 2.5 9.4.77 2.69 0.52.86 2.8.6.98.06 2 / 4.7 2.0.8 Low carbon steel Plain Designed to be used in the suspension of a hanger rod from the center of an I-beam. The clamp s design allows the load to be distributed equally on either side of the beam. Normally used in conjunction with Fig. 55 welded eye rod or Fig. 5 weldless eye nut. APPROVALS: Complies with Federal Specifications A-A-92A (Type 2) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 2). Fig. 620 HEAVY DUTY CENTER LOAD BEAM CLAMP Type Bolt Max. Rec. No. B C Size Load/lbs. 4 / 4 2 / 4 5 / 8 000 5 / 4 2 / 4 5 / 8 250 6 / 4 2 / 4 / 4 500 Flange Width Specify type number, width of flange and figure number. Max. Flange Wt. Each (in lbs.) Thickness Type 4 Type 5 Type 6 4 / 2.92 4.82 5 5 / 8 4.28 5.2 6.6 6 / 4 4.45 5.52 7.27 7 7 / 8 4.76 5.9 7.6 8 7 / 8 5.25 6.2 8.57 9 5.7 6.57 9.2 0 5.94 6.98 9.8 6.5 7.95 0.52 2 / 4 6.97 8.50. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Low carbon steel Plain 6

Center Load Beam Clamps Fig. 625 STEEL CENTER LOAD BEAM CLAMP Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Low carbon steel Plain Fig. 60 MALLEABLE IRON CENTER LOAD BEAM CLAMP Designed to be used in the suspension of a hanger rod from the center of an I-beam. The clamp provides a vertical adjustment of approximately 2". Specify rod size, flange width and figure number. NOTE: Box style furnished on some sizes. Rod Size A B C 4 5 6 7 8 0 2 / 8 4 550.68.8.9 2.05 2.4 2.5 2.59 / 2 4 850 2.0 2.7 2. 2.46 2.56 2.82. 5 / 8 / 4 4 / 2 00.28.52.7.95 4. 4.49 4.9 / 4 / 4 4 / 2 500 4.4 4.66 4.95 5.25 5.46 5.96 6.55 7 / 8 / 2 5 2600 6.57 6.67 7.05 7.44 7.7 8.40 9.8 / 2 5 400 7.97 8.24 8.77 9.26 9.62 0.46.4 / 8 / 2 5 / 2 600 4.46.69.74 5.07 5.60 6.86 8.2 / 4 / 2 5 / 2 8000 8.76 8.7 8.45 9.82 20.6 22.2 24.8 Max. Rec. Load/lbs. Wt. Each (in lbs.) Flange Width (inches) Designed to be used in the suspension of a hanger rod from the center of an I-beam. The clamp s design allows the load to be distributed equally on either side of the beam. The clamp is adjustable from 2 / 8 " to 7" and can be used with flange thicknesses up to.60 inches. Normally used in conjunction with Fig. 25 extension piece. An additional " or more of vertical adjustment is obtained when used with Fig 25. APPROVALS: Complies with Federal Specifications A-A-92A (Type 0) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 0) Specify figure number. If extension piece is required, order Fig. 25 extension piece separately. Malleable iron Plain Max. Rod Size B Rod Take Out (Clamp only) Beam Flange Width (inches) 2 / 8 4 5 6 7 Max. Rec. Load/lbs. Wt. Each (in lbs.) 7 / 8 / 2 7 / 6 5 / 6 2 5 / 6 2 9 / 6 7 / 8 65 2.49 64 Fig. 65 ADJUSTABLE STEEL BEAM CLAMP Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Low carbon steel Plain Rod Size A Designed to be used in the suspension of a hanger rod from an I-Beam. The clamp is adjustable from 2 to 8" and can be used with flange thicknesses up to.75 inches. APPROVALS: Complies with Federal Specifications A-A-92A (Type 27) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 27). Specify rod size and figure number. Flange Width (inches) Max. Rec. Load/lbs. Wt. Each (in lbs.) Min. Max. B C / 8 / 2 8 2 / 4 / 2 00.04 / 2 / 2 8 2 / 4 / 2 700.45 5 / 8 / 2 8 2 / 4 / 2 000.96 / 4 6 8 4 2 800 6.50

Pipe Covering Protection Saddles Designed to protect insulation on high temperature pipe lines. The saddle is furnished with notches to minimize surface contact with the pipe, thereby keeping heat loss to a minimum. APPROVALS: Complies with Federal Specifications A-A-92A (Type 9) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 9). Pipe Size Pipe Roller Size Use With Fig. No. 460, 480 48, 490 Low carbon steel Plain Specify pipe size, insulation size and figure number. 470 475 486 487 Fig. 460 480 48 490 B Fig. 470 475 B C Fig. 486 487 D Actual Thickness of Covering Max. Rec. Load (in lbs.) Wt. Each (in lbs.) / 4 2 2 / 2 2 - / 2 2 / 6 2 / 8 5 / 8 2 / 4 7 / 8 200.4 2 / 2 2 - / 2 2 5 / 6 2 / 4 / 6 2 7 / 6 / 6 200.4 / 4 2 / 2 2 - / 2 2 / 2 2 7 / 6 5 / 6 2 9 / 6 7 / 8 200.4 / 2 / 2 2 - / 2 2 5 / 8 2 5 / 8 2 / 8 2 / 6 200.4 2 / 2 4 2 - / 2 2 5 / 6 2 / 8 / 6 / 6 200.52 2 / 2 / 2 5 2 - / 2 / 4 / 4 2 / 6 5 / 6 / 6 200.52 4 5 2 - / 2 / 2 / 2 2 5 / 6 9 / 6 200.6 / 2 5 6 4-6 4 4 5 / 6 5 / 6 / 4 200.98 4 5 6 4-6 4 / 4 4 / 4 9 / 6 4 / 6 / 6 800.98 5 6 8 4-6 4 / 6 4 / 6 4 / 8 4 / 4 800.98 6 8 8 4-6 5 / 8 5 / 8 4 / 2 5 / 4 800.9 8 0 2 8-0 7 / 6 7 / 6 6 7 / 6 / 2 800 4.75 0 2 4 8-0 8 5 / 6 8 / 2 7 / 4 8 5 / 6 9 / 6 800 4.75 2 4 6 2-4 8 5 / 6 8 7 / 8 7 5 / 8 8 / 6 / 6 5000 6.88 Fig. 65 PIPE SADDLE FOR " INSULATION Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. FOR PIPE SIZES LESS THAN 2" FOR 2" PIPE SIZES AND UP Pipe Size Pipe Roller Size Use With Fig. No. 460, 480 48, 490 470 475 486 487 Fig. 460 480 48 490 B Fig. 470 475 B / 4 / 2 2 - / 2 2 / 4 2 / 4 2 / 6 2 7 / 8 7 / 6 4 2 - / 2 2 7 / 8 2 7 / 8 2 5 / 6 9 / 6 / 4 / 2 5 2 - / 2 / 6 / 6 2 9 / 6 / 6 5 / 8 / 2 / 2 5 2 - / 2 / 4 / 4 2 5 / 8 5 / 6 / 2 2 4 5 2 - / 2 / 2 / 2 2 7 / 8 9 / 6 9 / 6 2 / 2 5 6 4-6 4 4 5 / 6 5 / 6 7 / 8 5 6 4-6 4 5 / 6 4 5 / 6 5 / 8 4 / 4 9 / 6 / 2 6 8 4-6 4 9 / 6 4 9 / 6 / 6 4 / 2 / 6 4 6 8 4-6 4 7 / 8 4 7 / 8 4 / 6 4 / 4 9 / 6 5 8 8 4-6 5 / 2 5 / 2 4 / 6 5 / 8 / 2 6 8 0 8-0 5 7 / 8 5 / 6 5 / 6 6 / 2 8 0 2 8-0 7 / 6 7 / 6 6 7 / 6 / 2 0 2 4 8-0 8 5 / 6 8 / 2 7 / 4 8 5 / 6 9 / 6 2 4 6 2-4 9 / 2 9 / 2 8 / 6 9 / 4 9 / 6 4 6 8 2-4 0 / 6 0 / 8 8 / 4 0 / 6 / 2 6 8 20 6-20 / 4 / 4 9 / 6 / 8 / 2 8 20 24 6-20 2 5 / 6 0 / 6 2 / 6 / 2 20 24 24 24 9 / 6 5 / 8 / 6 / 2 24 0 0 6 5 / 6 / 2 5 / 4 / 2 C Fig. 486 487 D Actual Thickness of Covering Max. Rec. Load (in lbs.) Wt. Each (in lbs.) 200.85 200.85 200.85 200.85 200.98 200 2.25 800 2.25 800 2.50 800 2.50 800 2.50 800 4.25 800 5.50 800 5.50 5000 8. 5000 8. 5000 9.0 5000 9.68 7200.00 7200.00 Fig. 65 PIPE SADDLE FOR 2 " INSULATION FOR PIPE SIZES LESS THAN 2" FOR 2" PIPE SIZES AND UP 65

Pipe Covering Protection Saddles Fig. 654 PIPE SADDLE FOR 2" INSULATION Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed to protect insulation on high temperature pipe lines. The saddle is furnished with notches to minimize surface contact with the pipe, thereby keeping heat loss to a minimum. APPROVALS: Complies with Federal Specifications A-A-92A (Type 9) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 9). Low carbon steel Plain Specify pipe size, insulation size and figure number. FOR PIPE SIZES LESS THAN 2" FOR PIPE SIZES 2" AND UP Pipe Roller Size Use With Fig. No. Fig. 460 480 48 490 B Fig. 470 475 B Fig. 486 487 D Actual Thickness of Covering Max. Rec. Load (in lbs.) Wt. Each (in lbs.) Pipe 460, 480 470 486 Size 48, 490 475 487 C / 4 4 5 2 - / 2 5 / 6 5 / 6 2 / 6 / 8 7 / 8 200 2.58 4 5 2 - / 2 / 2 / 2 2 7 / 8 / 2 2 / 8 200 2.58 / 4 4 5 2 - / 2 5 / 8 5 / 8 / 6 5 / 6 200 2.58 / 2 5 6 4-6 4 4 5 / 6 7 / 8 2 5 / 6 800 2.85 2 5 6 4-6 4 / 4 4 / 4 9 / 6 4 / 6 2 / 8 800 2.85 2 / 2 6 8 4-6 4 / 2 4 5 / 8 7 / 8 4 / 2 2 5 / 6 800 2.85 6 8 4-6 4 / 6 4 / 6 4 / 8 4 / 6 2 / 6 800.0 / 2 8 8 4-6 5 / 8 5 / 8 4 5 / 6 5 2 / 4 800.0 4 8 8 4-6 5 / 8 5 / 8 4 9 / 6 5 / 4 2 / 6 800.0 5 8 0 8-0 6 6 / 6 5 / 6 6 / 8 2 800.0 6 0 0 8-0 6 7 / 6 6 7 / 6 5 / 2 6 / 2 2 800 5.25 8 0 2 8-0 7 9 / 6 7 9 / 6 6 / 2 7 9 / 6 2 800 6.0 0 4 6 2-4 9 / 6 9 7 5 / 8 8 / 6 2 / 6 800 7.05 2 6 8 6-20 0 / 6 0 / 6 8 5 / 8 0 2 / 2 5000 9. 4 6 8 6-20 0 7 / 8 / 6 9 5 / 6 0 / 6 2 5000 9. 6 8 20 6-20 / 6 / 4 0 / 6 9 / 6 2 5000 0.68 8 20 24 24 2 7 / 8 5 / 6 2 / 6 2 7200 0.68 20 24 24 24 9 / 6 2 / 4 5 / 8 2 7200.96 24 0 0 6 5 / 6 4 5 / 4 2 7200.95 Fig. 655 PIPE SADDLE FOR 2 2 " INSULATION FOR PIPE SIZES LESS THAN 2" FOR PIPE SIZES 2" AND UP Pipe Size Pipe Roller Size Use With Fig. No. 460, 480 48, 490 470 475 486 487 Fig. 460 480 48 490 B Fig. 470 475 B C Fig. 486 487 D Actual Thickness of Covering Max. Rec. Load (in lbs.) Wt. Each (in lbs.) / 4 5 6 4-6 4 / 8 4 / 8 / 4 4 / 8 2 7 / 6 200.25 / 2 6 8 4-6 4 / 2 4 5 / 8 7 / 8 4 / 2 2 / 6 800.25 2 6 8 4-6 4 / 4 4 / 6 4 / 6 4 / 4 2 5 / 8 800.25 2 / 2 8 8 4-6 5 / 8 5 / 8 4 / 4 5 2 7 / 8 800.6 8 8 4-6 5 7 / 6 5 7 / 6 4 / 6 5 5 / 6 2 9 / 6 800.6 / 2 8 0 8-0 5 5 / 8 5 5 / 8 4 / 6 5 / 6 2 / 4 800.70 4 8 0 8-0 5 5 / 6 5 5 / 6 5 6 2 9 / 6 800.70 5 0 0 8-0 6 9 / 6 6 9 / 6 5 5 / 8 6 5 / 8 2 9 / 6 800.70 6 0 2 8-0 7 / 8 7 / 6 6 / 6 7 / 4 2 / 2 800 6.0 8 2 4 8-0 8 5 / 6 8 / 2 7 / 4 8 5 / 6 2 / 6 800 6.80 0 4 6 2-4 9 9 / 6 9 9 / 6 8 / 8 9 5 / 6 2 9 / 6 800 7.0 2 6 8 6-20 0 / 6 0 9 / 6 9 / 8 0 / 2 2 5 / 8 5000 0.9 4 8 20 6-20 5 / 6 / 8 9 7 / 8 / 6 2 / 2 5000 0.9 6 20 24 6-20 2 5 / 6 0 / 6 2 / 6 2 / 2 7200.64 8 24 24 24 9 / 6 5 / 8 / 6 2 / 2 7200 2.92 20 24 24 4 / 6 2 / 4 4 / 6 2 / 2 7200 2.92 24 0 0 7 / 2 4 5 / 8 6 7 / 6 2 / 2 7200 4.9 66

Pipe Covering Protection Saddles Designed to protect insulation on high temperature pipe lines. The saddle is furnished with notches to minimize surface contact with the pipe, thereby keeping heat loss to a minimum. APPROVALS: Complies with Federal Specifications A-A-92A (Type 9) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 9). Low carbon steel Plain Specify pipe size, insulation size and figure number. Fig. 656 PIPE SADDLE FOR " INSULATION Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Size Pipe Roller Size Use With Fig. No. 460, 480 48, 490 470 475 486 487 Fig. 460 480 48 490 B Fig. 470 475 B C Fig. 486 487 D Actual Thickness of Covering Max. Rec. Load (in lbs.) Wt. Each (in lbs.) 2 8 8 4-6 5 / 8 5 / 8 4 9 / 6 5 / 4 / 8 800 4.0 2 / 2 8 0 4-6 5 5 / 8 5 / 4 4 7 / 8 5 / 2 / 8 800 4.0 8 0 8-0 6 6 5 / 6 6 / 6 / 6 800 4.2 / 2 0 0 8-0 6 5 / 6 6 5 / 6 5 / 8 6 / 8 5 / 6 800 4.2 4 0 0 8-0 6 9 / 6 6 9 / 6 5 5 / 8 6 5 / 8 / 6 800 4.2 5 0 2 8-0 7 / 8 7 / 4 6 / 6 7 / 4 / 6 800 4.2 6 2 2 8-0 7 5 / 8 7 5 / 8 6 9 / 6 7 5 / 8 800 8.0 8 4 6 2-4 9 9 7 / 6 8 / 4 / 8 800 8.0 0 6 8 6-20 0 / 8 0 / 6 8 / 6 0 / 6 800 8.40 2 8 20 6-20 / 8 / 4 9 5 / 8 / 6 5000.88 4 8 20 6-20 / 4 / 4 0 5 / 6 5 / 8 5000.88 6 20 24 24 2 7 / 8 / 6 2 7 / 6 7200.87 8 24 24 24 4 / 6 2 / 4 5 / 8 7200.87 20 24 24 5 / 4 5 / 6 4 / 4 7200 4.5 24 0 0 8 / 6 5 / 4 7 7200 5.86 FOR PIPE SIZES LESS THAN 2" FOR PIPE SIZES 2" AND UP Pipe Roller Size Use With Fig. No. Fig. 460 480 48 490 Fig. Fig. Actual Max. 470 486 Thickness Rec. Wt. Pipe 460, 480 470 486 475 487 of Load Each Size 48, 490 475 487 B B C D Covering (in lbs.) (in lbs.) 4 0 2 8-0 7 5 / 8 7 5 / 8 6 / 2 7 9 / 6 4 / 6 800 5.90 5 2 4 8-0 8 / 6 8 / 8 7 / 8 8 / 6 4 / 6 800 5.90 6 4 6 2-4 9 9 7 9 / 6 8 / 4 4 / 8 800 0.68 8 6 8 2-4 0 / 8 0 / 8 8 / 6 9 7 / 8 4 / 6 800 0.68 0 8 20 6-20 / 4 / 4 9 / 4 / 8 4 / 6 800.40 2 20 24 6-20 2 / 8 0 / 6 2 / 6 4 / 8 5000 4.4 4 20 24 24 2 7 / 8 5 / 6 2 5 / 8 4 5000 4.4 6 24 24 24 4 / 8 5 / 8 2 / 6 4 7200 5.79 8 24 24 5 / 4 5 / 6 4 / 4 4 7200 5.79 20 0 0 7 4 / 8 5 7 / 8 4 7200 6.90 24 0 0 9 / 4 6 7 / 6 9 / 4 4 7200 7.78 Fig. 658 PIPE SADDLE FOR 4" INSULATION FOR PIPE SIZES LESS THAN 2" FOR PIPE SIZES 2" AND UP 67

Pipe Alignment Guides Fig. 670-678 PIPE ALIGNMENT GUIDES INSULATION THICKNESS Fig. 670 NONE Fig. 67 " Fig. 67 / 2 " Fig. 674 2" Fig. 675 2 / 2 " Fig. 676 " Fig. 677 / 2 " Fig. 678 4" Designed for use with insulated or non-insulated pipe lines to direct the axial expansion and contraction of the pipe. The use of two or more guides on both sides of the expansion joint is recommended to avoid a pivoting effect. The first pipe guide should be placed a maximum of 4 pipe diameters from an expansion joint. Pipe guides are not designed to support any of the piping system s weight therefore additional supports are required. The maximum operating temperature should not exceed 750 F. Carbon Steel Painted Specify pipe size and figure number. Body No. B C D E F G H Axial Movement Wt. Each (in lbs.) 4 5 7 / 8 / 2 6 / 8 4 / 8 5 / 8 / 4 6 5 6 / 4 4 7 / 8 4 / 8 5 / 8 / 4 8 6 7 5 / 8 4 / 8 8 / 8 5 / 8 5 / 8 / 4 0 8 9 / 4 5 / 4 0 / 8 6 / 8 5 / 8 / 4 0 5 / 8 6 / 4 2 / 8 7 5 / 8 2 / 4 4 4 20 2 / 8 7 4 / 8 8 / 4 5 / 8 2 / 4 4 4 25 4 5 / 8 7 7 / 8 6 / 8 9 7 / 8 / 4 4 6 6 40 6 7 8 7 / 8 8 / 8 0 7 / 8 / 4 4 6 6 45 8 8 / 4 9 / 4 20 / 8 7 / 8 / 4 4 6 6 55 20 2 0 7 / 8 22 / 8 / 4 / 4 6 8 6 65 22 2 / 8 2 / 8 24 / 8 4 / 2 7 / 8 6 8 6 95 24 25 26 / 8 5 / 2 7 / 8 6 8 6 5 26 27 / 4 4 / 4 28 / 8 7 / 8 / 8 6 8 6 5 0 / 2 6 / 2 2 / 8 9 / 4 / 8 6 8 6 50 Note: Refer to pipe guide selection chart on page 69 to determine body number. 68

Pipe Guide Charts Body No. Insulation Thickness Pipe Size None / 2 2 2 / 2 / 2 4 / 2 4 4 4 5 6 8 8 0 / 4 4 4 5 6 8 8 0 0 4 4 5 6 8 8 0 0 / 4 4 4 5 6 8 8 0 0 / 2 5 5 5 6 8 8 0 0 2 5 5 6 8 8 0 0 2 2 / 2 6 6 6 8 8 0 0 2 6 6 8 8 0 0 2 2 4 8 8 8 0 0 2 2 4 5 0 0 0 0 2 2 6 6 6 0 0 0 2 2 4 6 6 8 2 2 2 4 6 6 8 8 0 6 6 6 6 8 8 20 20 2 8 8 8 8 20 20 22 22 4 20 20 20 20 20 22 22 24 6 22 22 22 22 22 24 24 26 8 24 24 24 24 24 26 26 0 20 26 26 26 26 26 0 0 0 24 0 0 0 0 0 Fig. No. 670 67 67 674 675 676 677 678 PIPE GUIDE SELECTION CHART For Fig. 670-678 Use selection chart to determine body number for dimensional purposes on page 68. PIPE GUIDE SPACING CHART Pipe Max. Distance between intermediate guides (in feet) for pressure (psig) Size 50 00 50 200 250 00 50 400 500 600 8 27 22 20 8 7 5 4 2 4 52 7 2 27 25 2 22 9 7 6 6 66 47 40 5 28 27 25 2 20 8 85 62 5 45 40 6 5 2 29 27 0 0 75 62 54 50 45 42 40 5 2 2 8 85 70 60 55 50 46 4 40 5 4 20 87 72 62 57 52 48 45 4 7 6 0 95 78 68 6 57 52 49 45 4 8 45 05 87 75 68 62 58 55 50 45 20 55 0 92 90 7 68 62 58 5 49 24 80 28 05 90 8 75 70 65 60 54 Note: The first pipe guide should be placed a maximum of 4 pipe diameters from an expansion joint. 69

Pipe Slide Assembly Fig. 690 PIPE SLIDE ASSEMBLY Designed to be welded directly to the pipe to allow for support from below and allow for horizontal movement with a low coefficient of friction. The assembly consists of a carbon steel tee with a polished stainless bottom which rests on a PTFE (glass filled teflon) plate, bonded to a carbon steel plate. The base plate configuration will vary with the Type selected. Maximum temperature: 200 o F at the sliding surface. Greater height dimensions, longer transverse and longitudinal movements, and other customer requirements can be supplied upon request. APPROVALS: Complies with Federal Specifications A-A-92A (Type 5) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 5). Carbon Steel, Stainless Steel, PTFE. Plain, Painted, Hot-Dip Galvanized. Specify pipe size, figure number, travel, and type. Pipe Size Max Y Type Type L Types Load* Travel A B&C A,B,C 5 8-/2 Up 0 -/4 4-/4 -/2 4 -/2 -/2 6 5.5 to 7000 5 8-/2 8" 20 2-/2 0" 5 0-/2 to 500 0 -/4 4-/4 5-/2 6 4-/2 4-/2 7 20.7 24" 5 20-/2 20 25-/2 *Based upon 500 psi/5.2 Kg per sq. cm. pressure on the PTFE. Dimensions Temperature Loads Weight Inches Fahrenheit Pounds Pounds K Types A,B,C W Types A,B,C Type A X Type B&C Weight Each 70

Notes 7

J-Hooks Fig. 80 RETURN LINE STRAIGHT J-HOOK Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. 5" 9 / 6 " Designed to support pipe running along the wall, in applications where clearance between the pipe and the wall is not desired. Low carbon steel Plain Specify pipe size and figure number. Pipe Max. Rec. Wt. Each Size B C Load/lbs. (in lbs.) / 2 6 9 / 2 5 / 8 200.5 / 4 6 / 8 / 6 200.5 6 9 / 6 7 / 8 200.80 / 4 6 5 / 8 / 6 200.8 / 2 6 / 6 / 6 200.87 2 7 / 2 5 / 8 200.9 2 / 2 7 5 / 2 / 6 50.6 7 5 / 8 2 50.27 / 2 8 / 2 2 / 4 50.7 4 8 9 / 6 2 5 / 8 450 2.9 5 9 / 6 450.50 6 9 / 8 / 6 450 4.5 Fig. 820 RETURN LINE OFFSET J-HOOK Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. 5" " 9 / 6 " Designed to support pipe running along the wall, in applications where clearance between the pipe and the wall is desired. Low carbon steel Plain Specify pipe size and figure number. Pipe Max. Rec. Wt. Each Size B C Load/lbs. (in lbs.) / 2 6 9 / 2 5 / 8 200.5 / 4 6 / 8 / 6 200.55 6 9 / 6 7 / 8 200.8 / 4 6 5 / 8 2 / 6 200.84 / 2 6 / 6 2 / 6 200.89 2 7 / 2 2 5 / 8 200.96 2 / 2 7 5 / 2 2 / 6 50.26 7 5 / 8 50.8 / 2 8 / 2 / 4 50.47 4 8 9 / 6 5 / 8 450 2.9 5 9 4 / 6 450.90 6 9 / 8 4 / 6 450 4.25 72

Pipe Straps Designed to hold pipe or conduit flush with mounting surface for light duty applications. Low carbon steel Electro-galvanized Specify pipe size and figure number. Fig. 825 TWO HOLE PIPE STRAP Pipe Size B C D Wt Each (in lbs.) / 4 5 / 8 / 8 5 / 8.0 / 8 2 / 8 5 / 8 / 6.0 / 2 2 5 / 8 7 / 8 7 / 8.04 / 4 2 / 4 2 / 8 / 8.05 / 8 2 5 / 8 7 / 6.06 / 4 4 / 4 / 6 / 6.08 / 2 4 / 2 / 2 5 / 6.0 2 5 / 8 4 / 8 2 9 / 6. 2 / 2 6 4 / 2 / 6.20 7 / 4 5 / 4 / 4.50 4 6 / 4 5 / 4 4 / 6.5 Note: Also available in copper tubing sizes with copper finish. To order, specify figure 826 and tube size. Designed to hold pipe flush with mounting surface. APPROVALS: Complies with Federal Specifications A-A-92A (Type 26) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 26). Fig. 80 SHORT PIPE STRAP Low carbon steel Plain Specify pipe size and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Pipe Hole Max. Rec. Wt. Each Size B C D E Size Load/lbs. (in lbs.) / 2 7 / 8 5 / 6 2 7 / 8 5 / 6 7 / 6 00.25 / 4 4 / 6 7 / 6 / 6 / 8 7 / 6 00.27 4 5 / 6 9 / 6 5 / 6 / 8 7 / 6 00.29 / 4 4 / 6 / 6 / 6 5 / 8 7 / 6 00. / 2 4 5 / 6 / 6 5 / 6 2 7 / 6 00.5 2 5 / 2 5 / 6 4 / 2 2 / 4 7 / 6 00.4 2 / 2 6 / 6 5 2 7 / 8 7 / 6 500.89 6 5 / 8 / 2 5 5 / 8 / 2 7 / 6 500.06 / 2 7 / 8 / 4 6 / 8 4 7 / 6 500.2 4 8 / 8 2 7 / 8 4 / 2 9 / 6 500.58 7

Pipe Clamps Fig. 85 ONE HOLE CLAMP Designed for the support of standard conduit, cable or wrought iron and steel pipe on walls or sides of beams. Not recommended for use horizontally on ceilings or bottoms of beams since the factor of safety is greatly reduced when so used. Malleable iron Plain Pipe Size Specify pipe size and figure number. Cable Size or Outside Dia. of Conduit Screw Hole Size Size Expansion Case or Screw Anchor Wt. Each (in lbs.) / 8.67 / 4 / 6 X.0 / 2.84 5 / 6 / 4 X / 2.04 / 4.05 5 / 6 / 4 X / 2.05. 5 / 6 / 4 X / 2.09 / 4.66 / 8 / 4 X / 2.2 / 2.90 7 / 6 / 8 X 2.6 2 2.7 7 / 6 / 8 X 2.25 2 / 2 2.87 / 6 5 / 8 X.49.50 / 6 5 / 8 X.82 4 4.50 / 4 5 / 8 X / 2.2 Fig. 840 RIGHT ANGLE CLAMP Designed for anchoring pipe or conduit at a right angle to structural members. Malleable iron with low carbon steel U-bolt and nuts Electro-galvanized Specify pipe size and figure number. Pipe Rod Size Wt. Each Size A B (in lbs.) / 8 / 4 / 6. / 2 5 / 6 2.4 / 4 5 / 6 2 5 / 6.42 5 / 6 2 5 / 8.47 / 4 5 / 6 2 7 / 8.54 / 2 5 / 6 / 4.57 2 / 8 7 / 8.85 2 / 2 / 8 4 / 8.06 / 8 5 / 8.0 / 2 / 8 5 / 2.28 4 / 8 6.40 74

Wall Brackets Designed to suspend hanger rod for support of light loads under 750 lbs. Normally used in conjunction with Fig. 850C wall bracket clip. APPROVALS: Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Low carbon steel Plain Fig. 850 LIGHT DUTY WALL BRACKET Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Specify type number and figure number. Type Number Hole Size Max. Rec. Load/lbs. Wt. Each (in lbs.) B C D E 9 6 / 2 / 6 8 750 6.00 2 0 / 2 / 6 2 750 8.70 9 6 / 2 / 6 8 750 0.60 Designed for use in conjunction with Fig. 850 wall bracket, to allow the rod to be suspended at any point along the length of the bracket. Low carbon steel Plain Specify rod size and figure number. Fig. 850C WALL BRACKET CLIP For Fig. 850 Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Rod Size For Pipe Sizes Wt. Each (in lbs.) / 8 / 2 to 2.7 / 2 2 / 2 to / 2.44 75

Wall Brackets Fig. 855 MEDIUM DUTY WALL BRACKET Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed for the support or suspension of loads up to 500 lbs. from walls or structures. The " space between the angles allows the rod to be placed anywhere along the length of the brackets. APPROVALS: Complies with Federal Specifications A-A-92A (Type 2) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 2). Low carbon steel Plain Specify type number and figure number. Hole Type Size Angle Iron Max. Rec. Wt. Each No. B C D E F G H Size Load/lbs. (in lbs.) 0 5 / 2 2 / 6 2 / 2 / 4 8 4 / 2 X / 2 X / 6 500 7.40 2 / 2 8 / 6 2 / 2 / 4 24 4 / 2 / 4 X / 4 X / 6 500 27.0 2 27 / 2 24 / 6 2 / 2 / 4 0 5 2 X 2 X / 4 500 47.60 Fig. 860 HEAVY DUTY WALL BRACKET Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Type No. B C 0 5 / 4 2 / 6 2 / 4 / 2 8 4 * 2 X. / 2 X. / 4 000 24. 2 / 8 8 5 / 6 2 / 4 / 8 24 5 2 / 4 2 X.2 X. / 4 000 5.80 2 27 / 2 24 / 6 2 / 4 / 4 0 5 2 / 2 2 / 2 X.2 X. 5 / 6 000 65.84 / 4 0 / 6 / 2 6 5 2 / 2 2 / 2 X.2 X. 5 / 6 000 82.0 4 9 6 / 6 / 2 42 6 / 2 / 2 X.2 / 2 X. / 8 000 40.52 5 46 42 / 6 / 2 2 50 6 / 2 / 2 X.2 / 2 X. / 8 000 66.40 *one hole Designed for the support or suspension of loads up to 000 lbs. from walls or structures. The " space between the angles allows the rod to be placed anywhere along the length of the brackets. APPROVALS: Complies with Federal Specifications A-A-92A (Type ) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type ). Low carbon steel Plain Specify type number and figure number. Hole Size D E F G H J Angle Iron Size Max. Rec. Load/lbs. Wt. Each (in lbs.) 76

Pipe Supports Designed to support horizontal pipe from floor stanchions. Normally used in conjunction with Fig. 87 threaded base stand. Steel Plain Specify pipe size and figure number. Pipe Coupling Wt. Each Size Pipe Size B (in lbs.) / 2 / 4 / 4.85 2 / 4 5 / 8.2 2 / 2 / 2 7 / 8.62 / 2 4 / 6.79 / 2 / 2 4 7 / 6.94 4 2 4 / 4 2.7 5 2 5 5 / 6.09 6 2 / 2 6 5 / 6 5.86 8 2 / 2 7 5 / 6 6.88 0 9 / 8 0. 2 0 / 8.28 Fig. 870 PIPE SADDLE SUPPORT WITH COUPLING Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed for use as a base stand for pipe supports. Steel Plain Fig. 87 THREADED BASE STAND Specify pipe size, height and figure number. Pipe Hole Size Thread Length Wt. Each Size B C D Plate Size (in lbs.) 9 / 6 / 2 / 4 X 6 X 6 4.95 / 4 9 / 6 / 2 / 4 X 6 X 6 5.8 / 2 9 / 6 / 2 / 4 X 6 X 6 6.49 2 9 / 6 / 2 / 4 X 6 X 6 7.85 2 / 2 / 4 9 / 6 / 2 / 8 X 8 X 8 5.24 / 2 / 6 / 2 / 8 X 2 X 2 26.24 4 / 2 5 / 6 2 / 2 X 2 X 2 5.94 6 / 2 / 8 2 / 2 X 8 X 8 7.46 Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Note: Wt. based on a height of 8". 77

Pipe Supports Fig. 875 ADJUSTABLE PIPE SADDLE SUPPORT Steel Plain Note: Gussets furnished on 8" and larger. APPROVALS: Designed to support horizontal pipe. Normally used in conjunction with Fig. 87 threaded base stand to provide vertical adjustment of the pipe. Complies with Federal Specifications A-A-92A (Type 8) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 8). Specify pipe size and figure number. Pipe Adjustment E Wt. Each Size B C D Min. Max. (in lbs.) 2 / 2 2 / 2 / 6 / 2 9 7 / 6 5 / 6 5.25 2 / 2 4 / 2 9 / 4 4 / 4 5.50 / 2 2 / 2 4 / 4 / 2 0 4 / 2 5.50 4 4 / 2 2 / 2 0 / 4 5 / 4 0.60 5 5 / 6 2 / 2 5 / 6 5 / 6 0.8 6 5 / 6 2 / 2 5 / 6 6 7 / 6 2.4 8 6 / 6 2 / 2 2 5 / 6 7 7 / 6 5.00 0 7 7 / 8 2 / 2 4 / 8 8 5 / 8 6.4 2 8 7 / 8 2 / 2 5 / 8 9 5 / 8 7.68 4 4 5 / 8 7 / 8 2 7 / 8 28.8 6 4 2 5 / 8 8 / 8 22 7 / 8 0.0 8 6 4 / 4 4 20 / 2 25 49.98 20 6 5 / 4 4 2 / 2 26 52.00 24 6 8 4 2 / 4 28 / 4 6.47 0 6 2 4 26 / 4 / 4 92.24 6 6 24 4 29 / 4 4 / 4 0.77 Fig. 876 ADJUSTABLE PIPE SADDLE SUPPORT WITH U-BOLT APPROVALS: Designed to support horizontal pipe. Normally used in conjunction with Fig. 87 threaded base stand to provide vertical adjustment of the pipe. The U-bolt is used to secure the pipe to the saddle. Complies with Federal Specifications A-A-92A (Type 8) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 8). Specify pipe size and figure number. Steel Plain Note: Gussets furnished on 8" and larger. 78 Pipe Adjustment E Dia. Wt. Each Size B C D Min. Max. F (in lbs.) 2 / 2 2 / 2 / 6 / 2 9 7 / 6 5 / 6 / 2 8.90 2 / 2 4 / 2 9 / 4 4 / 4 / 2 9.05 / 2 2 / 2 4 / 4 / 2 0 4 / 2 / 2 9.25 4 4 / 2 2 / 2 0 / 4 5 / 4 / 2.25 5 5 / 6 2 / 2 5 / 6 5 / 6 / 2.45 6 5 / 6 2 / 2 5 / 6 6 7 / 6 5 / 8 6.25 8 6 / 6 2 / 2 2 5 / 6 7 7 / 6 5 / 8 7.95 0 8 2 / 2 4 / 4 8 / 4 / 4 22.55 2 9 2 / 2 5 / 4 9 / 4 7 / 8 26.0 4 4 / 4 7 / 2 22 7 / 8 4.65 6 4 2 / 4 8 / 2 2 7 / 8 44.0 8 6 5 4 20 / 4 25 / 4 70.90 20 6 6 4 2 / 4 26 / 4 7.75 24 6 8 / 2 4 24 / 4 28 / 4 9.60 0 6 2 4 26 / 4 / 4 06.55 6 6 24 4 29 / 4 4 / 4 2.50

Pipe Supports Designed to provide up to 4 2 inches of vertical adjustment after installation. Normally used in conjunction with Fig. 87 threaded base stand, Fig. 880 pipe saddle support or Fig. 882 pipe saddle support with U-bolt. APPROVALS: Complies with Federal Specifications A-A-92A (Type 8) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 8) when used with Fig. 880. Fig. 877 PIPE SUPPORT ADJUSTER Steel pipe with malleable iron reducer. Plain Specify adjuster size and figure number. C Adjuster Size For Pipe Size B C Max. Adjustment Wt. Each (in lbs.) / 2 2 / 2 to / 2 2 / 2 / 2 4 / 2 4.05 2 / 2 4 to 2 2 / 2 8.0 4 to 6 4 4 / 2 2.60 4 8 to 6 6 4 22.60 B Fig. 878 & 879 PIPE SUPPORT ADJUSTERS Fig. 878 Fig. 879 Designed to provide up to 4 / 2 inches of vertical adjustment after installation. Steel pipe with malleable iron reducer. Plain Specify pipe size, figure number, and height to center of pipe. 79

Pipe Supports Fig. 880 PIPE SADDLE SUPPORT Steel Plain Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed to support horizontal pipe running close to the floor. Normally used in conjunction with floor stanchions. APPROVALS: Complies with Federal Specifications A-A-92A (Type 6) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 6). Specify pipe size and figure number. Pipe Pipe Size Wt. Each Size B C D E F (in lbs.) 2 / 2 4 2 / 2 / 6 / 2 / 2.67 4 / 2 4 / 2 / 2.76 / 2 4 7 / 6 4 / 4 / 2 / 2.88 4 4 4 / 4 4 / 2 2 / 8 2 / 2.60 5 4 4 / 6 5 / 6 2 / 8 2 / 2.8 6 4 6 / 6 5 / 6 2 / 8 2 / 2 5.50 8 4 7 5 / 6 6 / 6 2 / 8 2 / 2 7.00 0 4 9 5 / 8 7 7 / 8 2 / 8 2 / 2 7.66 2 4 / 6 8 7 / 8 2 / 8 2 / 2 8.95 4 4 2 / 8 5 / 8 2 7 / 8 6.54 6 4 7 / 8 2 5 / 8 2 7 / 8 8.70 8 4 5 9 / 2 4 / 4 4 4 27.98 20 4 7 5 / 6 5 / 4 4 4 0.20 24 4 20 25 / 2 8 4 4 4.46 0 4 26 2 4 4 76.24 6 4 / 6 24 4 4 88.77 80 Fig. 882 PIPE SADDLE SUPPORT WITH U-BOLT Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Steel Plain Designed to support horizontal pipe running close to the floor. The U-bolt securely holds the pipe to the saddle. APPROVALS: Complies with Federal Specifications A-A-92A (Type 7) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 7). Specify pipe size and figure number. Pipe Pipe Size Wt. Each Size B C D E F (in lbs.) 2 / 2 4 / 2 / 6 / 2 / 2 4.85 4 / 2 4 / 2 / 2 5.00 / 2 4 / 2 4 / 4 / 2 / 2 5.20 4 4 / 2 4 / 2 2 / 8 2 / 2 4.95 5 4 / 2 5 / 6 2 / 8 2 / 2 5.5 6 4 5 / 8 5 / 6 2 / 8 2 / 2 7.95 8 4 5 / 8 6 / 6 2 / 8 2 / 2 9.65 0 4 / 4 8 2 / 8 2 / 2 4.25 2 4 7 / 8 9 2 / 8 2 / 2 7.80 4 4 7 / 8 / 4 2 7 / 8 29.05 6 4 7 / 8 2 / 4 2 7 / 8.50 8 4 5 4 4 48.0 20 4 6 4 4 5.5 24 4 8 / 2 4 4 69.00 0 4 2 4 4 8.95 6 4 24 4 4 96.50

Adjustable Q-Deck Insert Seismic Brace Designed for installation in metal concrete deck forms to provide a means to support piping and equipment. Low carbon steel with electro-galvanized rod Plain Specify rod size and figure number. Fig. 885 ADJUSTABLE Q-DECK INSERT Rod Size A Thread Length Max. Rec. Wt. Each B C Load/lbs. (in lbs.) / 8 / 6 7 70.80 / 2 / 4 7 50.99 5 / 8 2 5 / 6 7 80.29 / 4 2 / 8 7 270 2.8 7 / 8 2 / 8 7 770 2.84 2 / 8 7 4960 2.97 Designed for bracing pipe against sway due to seismic disturbance. Often used in conjuction with Fig. 520 pipe clamp and Fig. 920 angle bracket at each end of the sway brace. Low carbon steel Plain Specify figure number. Fig. 890 SEISMIC BRACE Tapped Pipe Wt. Each Size B C D (in lbs.) 4 / 9 4 / 6.5 8

Welded Beam Attachment Fig. 900 & 900- WELDED BEAM ATTACHMENT Fig. 900 WITH BOLT AND NUT Fig. 900- WITHOUT BOLT AND NUT Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed for attaching hanger rod to the bottom flange of a beam. If installed in the inverted position, the hanger rod can be vertically adjusted otherwise bolt and nut are required. APPROVALS: Complies with Federal Specifications A-A-92A (Type 22) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 22). Low carbon steel Plain Specify rod size and figure number. Welded design furnished on / 2 " and larger. Max. Rec. Load/lbs. Wt. Each (in lbs.) Rod Size A B C D E F G H Bolt or Pin Size 650 F 750 F w/o B&N with B&N / 8 2 7 / 8 7 / 8 / 4 ga. 2 / 2 X 2 / 2 70 50.87. / 2 2 / 4 7 / 8 / 4 ga. 2 5 / 8 X 2 / 2 50 940.85.28 5 / 8 2 / 4 7 / 8 / 4 ga. 2 / 4 X 2 / 2 80 50.84.50 / 4 2 / 2 2 / 4 / 4 2 / 4 / 8 2 7 / 8 X 4 270 2260 2.00.04 7 / 8 2 / 2 / 4 / 4 2 / 8 / 8 X 4 / 2 770 50 2.50 4.02 / 2 / 2 2 / 4 / 2 / 8 X 5 4960 450 4.4 6.0 / 8 / 2 / 4 / 2 / 4 X 5 620 5200 4.7 7.5 / 4 4 / 2 2 2 / 2 5 / 8 / 8 X 6 / 2 8000 6660 8.50 2.62 / 2 5 4 2 / 2 2 / 2 / 4 4 5 / 8 X 6 60 9700 6.4 2.2 / 4 5 5 2 / 2 2 / 4 / 4 / 4 5 7 / 8 X 7 5700 4000 8.70 24.20 2 6 5 / 4 / 4 / 4 / 4 5 2 / 4 X 7 20700 8460 22.80 0.60 Note: The " size and larger are furnished with pin and cotter on Fig. 900. 82

Concrete Attachments Designed for attaching hanger rod to a concrete ceiling. Low carbon steel Plain Specify rod size and figure number. Fig. 90 CONCRETE ROD ATTACHMENT PLATE Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Dia. 4 Holes Rod Size Plate Max. Rec. Wt. Each A B C D E F Size load/lbs. (in lbs.) / 8 8 2 7 / 8 5 9 / 6 0 X 0 X / 8 70.60 / 2 8 2 7 / 8 5 9 / 6 0 X 0 X / 8 50.60 5 / 8 8 2 7 / 8 5 9 / 6 0 X 0 X / 8 80 5.0 / 4 8 / 4 5 / 6 0 X 0 X / 2 270 6.0 7 / 8 8 4 / 4 5 / 6 0 X 0 X / 2 770 6.70 2 8 4 / 2 6 / 6 2 X 2 X / 2 4960 4.90 / 8 2 8 4 / 4 6 / 6 2 X 2 X / 2 620 5.25 / 4 2 8 5 2 6 5 / 6 2 X 2 X / 4 8000 8.70 / 2 2 8 6 / 2 6 / 6 2 X 2 X 60 56.40 / 4 2 0 7 / 4 7 / 8 4 X 4 X / 4 5700 88.0 2 2 0 8 / 4 7 / 8 4 X 4 X / 4 20700 92.20 8

Concrete Attachments Fig. 904 CONCRETE CLEVIS PLATE Designed for use as a structural attachment to a concrete ceiling. Normally used in conjunction with Fig. 5 weldless eye nut or Fig. 55 welded eye rod. Low carbon steel Plain Specify rod size and figure number. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Rod Plate Size B C D E F G H J Size / 8 8 7 / 8 5 9 / 6 / 2 2 / 4 0 X 0 X / 8 / 2 8 7 / 8 5 9 / 6 5 / 8 2 / 4 0 X 0 X / 8 5 / 8 8 7 / 8 5 9 / 6 / 4 2 / 4 0 X 0 X / 8 / 4 8 / 4 5 / 6 7 / 8 2 2 / 4 0 X 0 X / 2 7 / 8 8 / 4 5 / 6 2 / 8 0 X 0 X / 2 2 8 / 2 6 / 6 / 8 2 / 4 2 X 2 X / 2 / 8 2 8 / 4 2 6 / 6 / 4 2 X 2 X / 2 / 4 2 8 2 2 6 5 / 6 / 8 / 2 2 X 2 X / 4 / 2 2 8 2 / 2 6 / 6 5 / 8 4 2 X 2 X / 4 2 0 2 / 4 7 / 8 7 / 8 5 / 4 4 X 4 X / 4 2 2 0 / 4 7 / 8 2 / 4 5 / 4 4 X 4 X / 4 Max. Rec. load/lbs. Wt. Each (in lbs.) 70.80 50.90 80 5.70 270 6.90 770 8.0 4960 6.90 620 7.75 8000 40.90 60 59.80 5700 9.60 20700 00.00 Note: The " size and larger are furnished with pin and cotter. 84

Upper Attachments Designed for attaching hanger rod to the side of wooden beams or walls. Normally secured in place with Fig. 48 wood drive screw. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers' Standardization Society ANSI/SP-69 and SP-58 (Type 4). Malleable iron Specify rod size and figure number. Rod Size Drive Screw Max. Rec. Wt. Each A B C Size Load/lbs. (in lbs.) / 8 2 / 6 9 / 6 #2 X / 2 250. / 2 2 / 4 / 4 #4 X / 2 480.25 Fig. 905 SIDE BEAM CONNECTOR Fig. 905 PLAIN Fig. 905C COPPER COLOR EPOXY FINISH Designed for attaching hanger rod to wood structures. Secured with Fig. 45 lag screw or two Fig. 48 wood drive screws, see chart. APPROVALS: Underwriters Laboratories Listed in the U.S. (UL) and Canada (CUL), and Factory Mutual Approved. Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). Low carbon steel Plain or electro-galvanized Specify figure number and finish. Rod Max. Wt. Size Pipe UL Listed Max. Rec. Each A Size Fasteners Load/Lbs (in lbs.) / 8 2 (2) #6 X 2 400.2 / 8 4 / 2 X 2 / 2 70.2 Designed to support pipe at various distances from a wall or column. Low carbon steel Plain Specify size number and figure number. Size Hole Size Max. Rec. Wt. Each No B C D Load/lbs. (in lbs.) 2 7 / 6 80.4 2 4 7 / 6 80.58 2 9 / 6 90.00 4 4 9 / 6 90.25 Fig. 906 STEEL SIDE BEAM CONNECTOR 9 / 2 " 9 / 2 " 2 9 / 2 " 9 / 6 " 9 / 2 " Fig. 90 REVERSIBLE ANGLE BRACKET Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. / 2 " / 2 " " 5 / 6 " A 85

Upper Attachments Fig.920 SIDE BEAM ANGLE BRACKET Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. Designed for use with wood, steel or concrete beams to provide a means for supporting hanger rod. When used on steel beams Fig. 920 can be welded or bolted in place. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). Low carbon steel Plain or Electro-galvanized Specify rod size, finish and figure number. Rod Max. Rec. Load/lbs. Wt. Size For Pipe Lag Bolted Each A Size B C D Screw to Steel (in lbs.) / 8 / 2 to 2 2 / 8 / 5 2 / 8 90 580.52 / 2 2 / 2 to / 2 2 / 8 / 2 5 / 8 640 960.50 5 / 8 4 to 5 2 / 2 / 2 760 500.75 / 4 6 2 / 2 / 2 80 2500.7 7 / 8 8 to 2 / 4 2 / 4 80 600.8 Fig. 925 REVERSIBLE SIDE BEAM ANGLE BRACKET Designed for attaching hanger rod to the side of beams or walls. Fig. 925 can accommodate either 8 or 2 inch rod. APPROVALS: Complies with Federal Specifications A-A-92A (Type 4) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 4). 9 / 6 " Low carbon steel Plain or Electro-galvanized 4 Holes D 7 / 6 " For Rod Size Specify finish and figure number. B C D Max. Rec. Load/lbs. Wt. Each (in lbs.) / 8 or / 2 2 / 6 9 / 2 500.50 86

Plate Washer & Welding Lug Designed as a heavy-duty washer to suspend hanger rods. Low carbon steel Plain Specify rod size and figure number. Standard A B C Rod Size Wt. Each (in lbs.) / 8 / 4 2 2.24 / 2 / 4 2 2.2 5 / 8 / 4 2 / 2 2 / 2.40 / 4 / 4 2 / 2 2 / 2.9 7 / 8 / 8.87 / 8 4 4.60 / 8 / 2 4 4 2.26 / 4 / 2 5 5.54 2 / 4 6 6 6.80 Fig. 90 SQUARE PLATE WASHER Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. A Designed to be welded to the underside of structural members to provide a means of supporting rod attachments. Used in conjunction with Fig. 8 forged steel clevis. APPROVALS: Complies with Federal Specifications A-A-92A (Type 57) and Manufacturers Standardization Society ANSI/SP-69 and SP-58 (Type 57). Low carbon steel Plain Fig. 95 & 96 WELDING LUG Fig. 95 LONG WELDING LUG Fig. 96 Available in stainless steel. To order, specify 04 or 6 and add suffix SS to figure number. Price on request. SHORT WELDING LUG Specify rod size and figure number. Rod Size Pin or Hole Size B C Max. Rec Bolt Short Long D E F Load/lbs. / 2 5 / 8 / 6 / 2 / 4 / 4 2 / 2 0 5 / 8 / 4 / 6 / 2 / 4 / 4 2 / 2 80 / 4 7 / 8 5 / 6 / 2 / 4 / 8 2 / 2 270 7 / 8 / 8 2 / 4 / 8 2 / 2 770 / 8 / 4 2 / 2 / 2 4960 / 4 / 8 / 2 4 2 5 / 8 4 8000 / 2 5 / 8 / 4 4 / 2 2 / 2 / 4 5 60 Wt. Each (in lbs.) Short Long.48.75.4.68.60.04.7.98.20.62.0.7 4.82 6.42 87

Channel CHANNEL GREEN QUALITY: POLYESTER Powder Properties Test Method Powder Properties Tolerances ASTM D45 (8.0) Specific Gravity. ± 0.0 ASTM D45 (8.0) Theoretical Coverage 44.58 ± 4.0 FT 2 /Lb/Mil. ASTM D45 () Volatile Content Max. 2.5% ASTM D45 () Storage Temperature Max 80 o F Coating Properties All tests performed on Substrate 0.02 CRS Pretreatment Bonderite 000 Test Coating Tolerances/ Method Properties Specifications ASTM D52 Gloss 20 o /60 o 70-80 ASTM D2454 Over Bake Resistance Time 00% ASTM D6 Pencil Hardness H - 2H ASTM D2794 (Modified) Direct Impact (Gardner) 80 in. Lbs. ASTM D2794 (Modified) Reverse Impact (Gardner) 80 in. Lbs. ASTM D598B Adhesion (Cross Hatch) Pass No Adhesion Loss ASTM D5222 Flexibility (Mandrel) /8 Bend No Fracture ASTM 7 Salt Spray 000 Hrs. ASTM D2247 Humidity 500 Hrs. Application Test Method Application Cure Schedule Electrostatic Spray Ambient Temperature 5' @ 90 o C (75 o F) Recommend Minimum Film Thickness.5 24

Channel Selection Chart Figure Material See Page Number Width Height Size Number 00-042 -5/8-5/8 2 Ga. 26 0-42 -5/8-5/8 4 Ga. 28 20-242 -5/8 /6 2 Ga. 0 0-42 -5/8 /6 4 Ga. 2 40-442 -5/8 2 Ga. 4 50-542 -5/8 -/4 2 Ga. 6 60-642 -5/8 2-7/6 2 Ga. 8 70-742 -5/8 -/8 2 Ga. 40 Holes Slots 9 /6 Dia. Holes 9 /6 5 /6 7 /8 TYP. /2 /8 2 Long Slots /2 Knockouts 7 /8 Dia. Knockouts /2 6 25

Channel 00-042 " X " X 2 Gauge 7 /8 9 /2.906 /8 Y X X.79 Y Specify Figure No., finish and number of feet. Fig. Number 0 ft. 20 ft. Type - Description Weight Per Foot (in Lbs.) Bundle Qty. 0 ft. 20 ft. 00 002 No Openings.77 500 500 00A 002A Welded Back to Back.54 200 00 0 02 With /8" X 9 /6" slots on 2" centers.70 500 500 0A 02A Welded Back to Back.40 200 00 02 022 With 9 /6" dia. holes on 7 /8" centers.80 500 500 02A 022A Welded Back to Back.60 200 00 0 02 With " slots.68 500 500 04 042 With 7 /8" Knockouts on 6" centers.77 500 500 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. 0-02 02-022 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. 0-02 /2 04-042 7 /8 Dia. Knockouts /2 6 26

Channel Elements of Selection X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 00.56.89.209.580.29.294.65 00A.22.958.589.924.478.588.65 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 00 0454 260.0 260 2" 00A 2625 260*.0 260* 00 9950 2269.0 2269 8" 00A 24 260*.0 260* 00 9 702.06 702 24" 00A 264 260*.02 260* 00 8582 6.09 6 0" 00A 2089 260*.0 260* 00 780 5. 5 6" 00A 2097 260*.06 260* 00 6998 972.7 972 42" 00A 9898 260*.09 260* 00 69 85.22 758 48" 00A 922 2405. 2405 00 592 756.28 599 54" 00A 8669 28.6 28 00 478 68.5 485 60" 00A 7940 924.20 924 00 4202 69.42 40 66" 00A 74 749.24 749 00 79 567.5 7 72" 00A 625 60.28 60 00 76 486.69 248 84" 00A 4255 74.8 255 00 2728 425.90 90 96" 00A 95 202.50 96 00 28 78. 50 08" 00A 9524 069.6 759 00 20 40.40 2 20" 00A 775 962.78 65 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. 00-042 For Fabricated Channels, reduce beam load values as follows: 0 & 02 5% 02 & 022 0% 0 & 02 0% 04 & 042 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding. 27

Channel 0-42 " X " X 4 Gauge /8 7 /8 9 /2.906 Y X X.79 Y Fig. Number 0 ft. 20 ft. Type - Description Weight Bundle Qty. Per Foot (in Lbs.) 0 ft. 20 ft. Specify Figure No., finish and number of feet. 0 02 No Openings.0 500 500 0A 02A Welded Back to Back 2.60 200 00 2 With /8" X 9 /6" slots on 2" centers.28 500 500 A 2A Welded Back to Back 2.56 200 00 2 22 With 9 /6" dia. holes on 7 /8" centers.0 500 500 2A 22A Welded Back to Back 2.74 200 00 2 With " slots.29 500 500 4 42 With 7 /8" Knockouts on 6" centers.0 500 500 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. -2 2-22 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. -2 /2 4-42 7 /8 Dia. Knockouts /2 6 28

Channel Elements of Selection 0-42 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 0.47.49.66.597.8.225.662 0A.84.74.456.942.66.450.662 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 0 644 750.0 750 2" 0A 22 750*.0 750* 0 5874 79.06 79 24" 0A 299 750*.0 750* 0 508 99. 99 6" 0A 2627 750*.05 750* 0 404 689.2 607 48" 0A 25 750*.2 750* 0 008 55.6 89 60" 0A 456 58.20 58 0 224 460.5 270 72" 0A 065 265.28 265 0 898 94.70 98 84" 0A 9700 084.8 990 0 608 45.9 52 96" 0A 8602 949.50 758 0 97 06.5 20 08" 0A 758 84.6 599 0 26 276.42 97 20" 0A 6024 759.78 485 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: & 2 5% 2 & 22 0% & 2 0% 4 & 42 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding. 29

Channel 20-242 " X /6" X 2 Gauge 7 /8 9 /2.470 Y /8 /6 /6 X X /6.42 Y Specify Figure No., finish and number of feet. Fig. Number Weight Bundle Qty. Type - Description Per Foot 0 ft. 20 ft. (in Lbs.) 0 ft. 20 ft. 20 202 No Openings.22 500 000 20A 202A Welded Back to Back 2.52 500 500 2 22 With /8" X 9 /6" slots on 2" centers.5 500 000 2A 22A Welded Back to Back 2.6 500 500 22 222 With 9 /6" dia. holes on 7 /8" centers.6 500 000 22A 222A Welded Back to Back 2.40 500 500 2 22 With " slots.5 500 000 24 242 With 7 /8" Knockouts on 6" centers.27 500 000 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. 2-22 22-222 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. 2-42 /2 24-242 7 /8 Dia. Knockouts /2 6 0

Channel Elements of Selection 20-242 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 20.76.0.068.297.5.42.554 20A.752.48.82.444.20.284.554 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 20 8407 079.02 079 2" 20A 960 270*.0 270* 20 759 59.0 506 24" 20A 7444 270*.05 270* 20 597 60.24 225 6" 20A 5275 0.4 0 20 78 270.4 26 48" 20A 2692 759.25 607 20 204 26.67 8 60" 20A 968 608.9 88 20-00 080.96 56 72" 20A 6780 506.56 270 20-00 54. 4 84" 20A 498 44.77 98 20-00 5.7 2 96" 20A 84 80.00 52 20-00 20 2.6 25 08" 20A 0 8.27 20 20-00 08 2.67 20 20" 20A -00 04.56 97 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: 2 & 22 5% 22 & 222 0% 2 & 22 0% 24 & 242 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding.

Channel 0-42 " X /6" X 4 Gauge 7 /8 9 /2.470 Y /8 /6 /6 X X /6.42 Y Fig. Number 0 ft. 20 ft. Type - Description Weight Bundle Qty. Per Foot (in Lbs.) 0 ft. 20 ft. 0 02 No Openings.9 500 000 Specify Figure No., finish and number of feet. 0A 02A Welded Back to Back.86 500 500 2 With /8" X 9 /6" slots on 2" centers.86 500 000 A 2A Welded Back to Back.72 500 500 2 22 With 9 /6" dia. holes on 7 /8" centers.88 500 000 2A 22A Welded Back to Back.92 500 500 2 With " slots.87 500 000 4 42 With 7 /8" Knockouts on 6" centers.97 500 000 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. -2 2-22 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. -2 /2 4-42 7 /8 Dia. Knockouts /2 6 2

Channel Elements of Selection 0-42 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 0.295.027.056.02.0.5.60 0A.590.22.50.455.220.270.60 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 0 686 870.0 870 2" 0A 276 870*.0 870* 0 5464 465. 40 24" 0A 25 870*.04 870* 0 400 0.24 9 6" 0A 087 82.4 82 0 270 2.4 08 48" 0A 9620 624.25 499 0 70 86.68 69 60" 0A 774 499.9 9 0 20 55.97 48 72" 0A 557 46.56 222 0 --- 0.2 5 84" 0A 409 57.76 6 0 --- 06.7 27 96" 0A 4 2.00 25 0 --- 0 2.9 2 08" 0A 2476 277.27 98 0 --- 9 2.70 7 20" 0A --- 250.56 80 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: & 2 5% 2 & 22 0% & 2 0% 4 & 42 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding.

Channel 40-442 " X " X 2 Gauge 7 /8 9 /2.577 Y /8 X X.42 Y Fig. Number 0 ft. 20 ft. Type - Description Weight Bundle Qty. Per Foot (in Lbs.) 0 ft. 20 ft. 40 402 No Openings.8 500 000 Specify Figure No., finish and number of feet. 40A 402A Welded Back to Back 2.88 500 400 4 42 With /8" X 9 /6" slots on 2" centers.4 500 000 4A 42A Welded Back to Back 2.72 500 400 42 422 With 9 /6" dia. holes on 7 /8" centers.9 500 000 42A 422A Welded Back to Back 2.78 500 400 4 42 With " slots. 500 000 44 442 With 7 /8" Knockouts on 6" centers.44 500 000 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. 4-42 42-422 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. 4-42 /2 44-442 7 /8 Dia. Knockouts /2 6 4

Channel Elements of Selection 40-442 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 40.40.055.095.57.6.20.66 40A.860.26.26.55.27.402.66 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 40 98 58.02 58 2" 40A 2094 590*.0 590* 40 87 769.09 769 24" 40A 9757 590*.04 590* 40 7050 5.20 88 6" 40A 8094 428. 428 40 5405 84.5 28 48" 40A 69 07.20 05 40 52 08.55 40 60" 40A 906 857.2 674 40 249 256.79 97 72" 40A 87 74.46 468 40 792 220.07 7 84" 40A 8645 62.62 44 40 -- 92.4 55 96" 40A 669 55.8 26 40 -- 07.78 4 08" 40A 520 476.0 208 40 -- 054 2.20 5 20" 40A 426 428.27 68 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: 4 & 42 5% 42 & 422 0% 4 & 42 0% 44 & 442 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding. 5

Channel 50-542 " X /4" X 2 Gauge /8 7 /8 9 /2.740 Y /4 /4 X X Y.50 /4 Fig. Number Weight Bundle Qty. Type - Description Per Foot 0 ft. 20 ft. (in Lbs.) 0 ft. 20 ft. 50 502 No Openings 2.99 00 00 Specify Figure No., finish and number of feet. 50A 502A Welded Back to Back 5.98 00 200 5 52 With /8" X 9 /6" slots on 2" centers 2.90 00 00 5A 52A Welded Back to Back 5.80 00 200 52 522 With 9 /6" dia. holes on 7 /8" centers 2.9 00 00 52A 522A Welded Back to Back 6.02 00 200 5 52 With " slots 2.89 00 00 54 542 With 7 /8" Knockouts on 6" centers 2.9 00 00 5-52 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. 52-522 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. 5-52 54-542 /2 7 /8 Dia. Knockouts /2 6 6

Channel Elements of Selection 50-542 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 50.902.5.64.2.46.57.695 50A.804 6.49.95.876.87.074.695 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 50 890 50.0 50 24" 50A 770 50*.0 50* 50 7 488.07 488 6" 50A 746 50*.02 50* 50 624 266.2 266 48" 50A 706 50*.04 50* 50 4988 209.8 209 60" 50A 650 50*.08 50* 50 86 744.26 744 72" 50A 5876 50*.4 50* 50 06 495.6 460 84" 50A 55 4552.9 4552 50 2564 08.47 8 96" 50A 4279 98.25 98 50 22 6.59 884 08" 50A 0 54.2 54 50 95 046.7 76 20" 50A 2226 87.9 87 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: 5 & 52 5% 52 & 522 0% 5 & 52 0% 54 & 542 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding. 7

Channel 60-642 " X 2 7 /6" X 2 Gauge /8 7 /8 9 /2.25 Y 2 7 /6 2 7 /6 X X Y.2 2 7 /6 Fig. Number Weight Bundle Qty. Type - Description Per Foot 0 ft. 20 ft. (in Lbs.) 0 ft. 20 ft. 60 602 No Openings 2.0 00 400 Specify Figure No., finish and number of feet. 60A 602A Welded Back to Back 4.60 200 200 6 62 With /8" X 9 /6" slots on 2" centers 2.2 00 400 6A 62A Welded Back to Back 4.46 200 200 62 622 With 9 /6" dia. holes on 7 /8" centers 2.25 00 400 62A 622A Welded Back to Back 4.86 200 200 6 62 With " slots 2.2 00 400 64 642 With 7 /8" Knockouts on 6" centers 2.48 00 400 6-62 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. 62-622 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. 6-62 /2 64-642 7 /8 Dia. Knockouts /2 6 8

Channel Elements of Selection 60-642 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 60.72.5.40.852.8.46.680 60A.464 2.874.79.40.676.82.680 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 60 040 880.0 880 2" 60A 20820 880*.0 880* 60 9244 27.04 27 24" 60A 2059 880*.0 880* 60 79 282.09 282 6" 60A 2007 880*.0 880* 60 686 66.5 66 48" 60A 95 880*.07 880* 60 4785 09.24 09 60" 60A 842 847*. 847* 60 77 09.5 947 72" 60A 709 206.9 206 60 052 95.47 696 84" 60A 6005 2748.26 2748 60 2600 88.62 5 96" 60A 4500 2404. 2404 60 227 727.77 42 08" 60A 2795 27.42 27 60 209 655.96 4 20" 60A 0889 924.52 844 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: 6 & 62 5% 62 & 622 0% 6 & 62 0% 64 & 642 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding. 9

Channel 70-742 " X /8" X 2 Gauge /8 7 /8 9 /2.750 Y /8 /8 X X.625 Y /8 Fig. Number Weight Bundle Qty. Type - Description Per Foot 0 ft. 20 ft. (in Lbs.) 0 ft. 20 ft. 70 702 No Openings.59 500 500 Specify Figure No., finish and number of feet. 70A 702A Welded Back to Back.40 200 00 7 72 With /8" X 9 /6" slots on 2" centers.54 500 500 7A 72A Welded Back to Back.24 200 00 72 722 With 9 /6" dia. holes on 7 /8" centers.65 500 500 72A 722A Welded Back to Back.0 200 00 7 72 With " slots.59 500 500 74 742 With 7 /8" Knockouts on 6" centers.70 500 500 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. 7-72 72-722 9 /6 9 /6 Dia. Holes /2 /8 2 5 /6 7 /8 TYP. 7-72 /2 74-742 7 /8 Dia. Knockouts /2 6 40

Channel Elements of Selection 70-742 X-X Axis Y-Y Axis Area of Moment Section Radius of Moment Section Radius of Figure Section of Inertia Modulus Gyration of Inertia Modulus Gyration Number Inches 2 Inches 4 Inches Inches Inches 4 Inches Inches 70.508.24.59.494.209.257.64 70A.06.6.445.776.48.54.64 Modules of Elasticity: 29,500,000 PSI Beam & Column Loads Beam Span Maximum Uniform Load Deflection Uniform Load Figure or Unbraced Column Load @ 25,000 PSI @ 25,000 PSI @ /240 Span Number Column Height (in Lbs.) (in Lbs.) (in Inches) (in Lbs.) 70 0278 220.02 220 2" 70A 220 220*.0 220* 70 904 299.07 299 24" 70A 20806 220*.02 220* 70 7640 866.5 866 6" 70A 9950 220*.08 220* 70 65 649.26 495 48" 70A 875 87.5 87 70 4778 520.4 7 60" 70A 720 454.2 454 70 870 4.59 220 72" 70A 526 2. 092 70 24 7.80 62 84" 70A 00 08.45 802 70 2774 25.04 24 96" 70A 0525 909.59 64 70 240 289.2 98 08" 70A 86 808.75 485 70 99 260.6 79 20" 70A 676 727.92 9 Beam Loads Loads listed are uniformly distributed, for loads concentrated at center of span multiply uniform load by.5 and multiply the deflection by.8. When deflection is not a factor use stress of 25,000 PSI. When deflection is a factor use deflection of /240 Span. *Failure determined by weld shear. Column Loads Column loadings are for allowable axial loads for the unsupported heights listed and include a K value of.80. If eccentric, loads should be reduced according to standard practice. For Fabricated Channels, reduce beam load values as follows: 7 & 72 5% 72 & 722 0% 7 & 72 0% 74 & 742 5% TECHNICAL DATA SPOT WELDING Resistance welding of back to back strut channel is accomplished by way of an AC powered press type spot welder. This equipment produces a series of spot welds from 2-/2" to " apart continuously down the length of the channel. Consistency is maintained by the use of a highly sophisticated constant current weld control. This processor is capable of maintaining weld sequence, duration and current control along with other variables. Any deviations in the programmed parameters will issue forth an alarm or shut down fault, which is then investigated. Weld quality is tested every 00-50 welds through the use of a destructive test method. Through the use of modern technology, destructive and non-destructive testing, the quality of strut can be maintained. Spot weld strut is fabricated in accordance with the R.W.M.A. guidelines for resistance welding. 4

Accessories 42

Strut Clamps I.P. Pipe Clamp Max. Rec. Fig. Pipe O.D. Std. Material Loads (in Lbs.) Wt. Each Number Size Size Package Size (in Lbs.) X Y Z 200 /8 00 6 Ga. 50 50 400.0 2002 /2 00 6 Ga. 50 50 400.0 200 /4 00 4 Ga. 75 75 600.4 2004 00 4 Ga. 75 75 600.7 2005 /4 00 4 Ga. 75 75 600.2 2006 /2 50 2 Ga. 25 25 800.0 2007 2 2 /8 50 2 Ga. 25 25 800.5 2008 2 /2 2 7 /8 50 2 Ga. 25 25 800.9 2009 /2 50 2 Ga. 25 25 800.46 200 /2 4 50 Ga. 50 200 000.65 20 4 4 /2 25 Ga. 50 200 000.66 202 5 25 Ga. 50 200 000.79 20 6 6 5 /8 25 Ga. 50 200 000.00 204 8 8 5 /8 25 Ga. 200 250 000.4 205 0 0 /4 25 Ga. 200 250 000.4 206 2 2 /4 25 Ga. 200 250 000.74 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. Universal Pipe Clamp for EMT, IMC & GRC Fig. Nominal O.D. Size Std. Material Max. Rec. Loads (in Lbs.) Wt. Each Number Size Range Package Size X Y Z (in Lbs.) 20 /8.557 to.706 00 6 Ga. 50 50 400. 202 /2.706 to.840 00 6 Ga. 50 50 400. 20 /4.922 to.050 00 4 Ga. 50 50 400.5 204.6 to.5 00 4 Ga. 50 50 400.7 205 /4.50 to.660 00 4 Ga. 50 50 400.9 206 /2.740 to.90 50 2 Ga. 75 75 600.0 207 2 2.97 to 2.75 50 2 Ga. 75 75 600.5 Specify figure number and nominal size. 200-206 Low carbon steel Electro-galvanized Specify figure number and pipe size. 20-207 Low carbon steel Electro-galvanized EMT Conduit Clamp 220-2207 Fig. EMT Std. Material Max. Rec. Loads (in Lbs.) Wt. Each Number Size Package Size X Y Z (in Lbs.) 220 /8 00 6 Ga. 50 50 400.09 2202 /2 00 6 Ga. 50 50 400.09 220 /4 00 6 Ga. 50 50 400.0 2204 00 4 Ga. 50 50 600.4 2205 /4 00 4 Ga. 50 50 600.6 2206 /2 50 2 Ga. 75 75 800.27 2207 2 50 2 Ga. 75 75 800.0 Specify figure number and EMT size. Low carbon steel Electro-galvanized 4

Strut Clamps 20-24 Low carbon steel Copper Color Epoxy Finish Specify figure number and tube size. 240-245 APPLICATION: For use with No-Hub Cast Iron Soil Pipe Fig. Number Low carbon steel Electro-galvanized Specify figure number and O.D. tube size. 44 No-Hub Cast Iron Soil Nom. Pipe Size 2006 /2 2007 2 2424 240 4 247 5 2445 6 2460 8 2477 0 249 2 Copper Tubing Clamp Max. Rec. Fig. Tube Std. Material Loads (in Lbs.) Wt. Each Number Size Package Size X Y Z (in Lbs.) 20 /4 00 6 Ga. 50 50 400.09 202 /8 00 6 Ga. 50 50 400.09 20 /2 00 6 Ga. 50 50 400.09 204 /4 00 6 Ga. 50 50 400.0 205 00 4 Ga. 75 75 600.4 206 /4 00 4 Ga. 75 75 600.6 207 /2 00 4 Ga. 75 75 600.7 208 2 50 2 Ga. 25 25 800.29 209 2 /2 50 2 Ga. 25 25 800.5 20 50 2 Ga. 25 25 800.40 2 /2 25 2 Ga. 50 200 000.5 22 4 25 2 Ga. 50 200 000.6 2 5 25 Ga. 50 200 000.74 24 6 25 Ga. 200 250 000.94 O.D. Tube Clamp Max. Rec. Fig. O.D. Std. Material Loads (in Lbs.) Wt. Each Number Size Package Size X Y Z (in Lbs.) 240 /4 00 6 Ga. 50 50 400.09 2402 /8 00 6 Ga. 50 50 400.09 240 /2 00 6 Ga. 50 50 400.0 2404 5 /8 00 6 Ga. 50 50 400.0 2405 /4 00 6 Ga. 50 50 400.0 2406 7 /8 00 6 Ga. 50 50 400.0 2407 00 4 Ga. 75 75 600. 2408 /8 00 4 Ga. 75 75 600.4 2409 /4 00 4 Ga. 75 75 600.4 240 /8 00 4 Ga. 75 75 600.6 24 /2 00 4 Ga. 75 75 600.6 242 00 4 Ga. 75 75 600.7 24 /4 50 2 Ga. 25 25 800.27 244 7 /8 50 2 Ga. 25 25 800.28 245 2 50 2 Ga. 25 25 800.28 246 2 /8 50 2 Ga. 25 25 800.29 247 2 /4 50 2 Ga. 25 25 800.2 248 2 /2 50 2 Ga. 25 25 800.4 249 2 5 /8 50 2 Ga. 25 25 800.5 2420 2 /4 50 2 Ga. 25 25 800.7 242 50 2 Ga. 25 25 800.9 2422 /8 50 2 Ga. 25 25 800.40 242 /4 50 2 Ga. 25 25 800.42 2424 /8 50 2 Ga. 25 25 800.4 2425 5 /8 50 Ga. 50 200 000.5 2426 /4 50 Ga. 50 200 000.5 2427 7 /8 50 Ga. 50 200 000.54 2428 4 /8 50 Ga. 50 200 000.57 2429 4 /4 25 Ga. 50 200 000.59 240 4 /8 25 Ga. 50 200 000.60 24 4 5 /8 25 Ga. 50 200 000.62 242 4 /4 25 Ga. 50 200 000.64 24 4 7 /8 25 Ga. 50 200 000.65 244 5 25 Ga. 50 200 000.67 245 5 /8 25 Ga. 50 200 000.68

Strut Clamps O.D. Tube Clamp - Cont d. Max. Rec. Fig. O.D. Std. Material Loads (in Lbs.) Wt. Each Number Size Package Size X Y Z (in Lbs.) 246 5 /4 25 Ga. 50 200 000.70 247 5 /8 25 Ga. 50 200 000.7 248 5 /2 25 Ga. 50 200 000.72 249 5 5 /8 25 Ga. 50 200 000.85 2440 5 /4 25 Ga. 50 200 000.87 244 5 7 /8 25 Ga. 50 200 000.88 2442 6 25 Ga. 50 200 000.90 244 6 /8 25 Ga. 200 250 000.94 2444 6 /4 25 Ga. 200 250 000.9 2445 6 /8 25 Ga. 200 250 000.95 2446 6 /2 25 Ga. 200 250 000.98 2447 6 /4 25 Ga. 200 250 000.99 2448 6 7 /8 25 Ga. 200 250 000.00 2449 7 25 Ga. 200 250 000.0 2450 7 /8 25 Ga. 200 250 000.02 245 7 /4 25 Ga. 200 250 000.04 2452 7 /8 25 Ga. 200 250 000.07 245 7 /2 25 Ga. 200 250 000.09 2454 7 5 /8 25 Ga. 200 250 000.0 2455 7 /4 25 Ga. 200 250 000.2 2456 7 7 /8 25 Ga. 200 250 000. 2457 8 25 Ga. 200 250 000.5 2458 8 /8 25 Ga. 200 250 000.7 2459 8 /4 25 Ga. 200 250 000.8 2460 8 /8 25 Ga. 200 250 000.20 246 8 /2 25 Ga. 200 250 000.2 Available in aluminum and stainless steel. Price on request. To order aluminum, add suffix AL to fig. number. To order stainless steel, specify 04 or 6 and add suffix SS to fig. number. Clamp With Cushion Fig. O.D. Size Nom. Tube Std. Wt. Each Number A Size B C D Package (in Lbs.) 250 /4 /8 /6.060 /2 0.2 2502 /8 /4 /4.060 5 /8 0. 250 /2 /8 /8.060 /4 0. 2504 5 /8 /2 /2.060 7 /8 20.5 2505 /4 5 /8 /4.075 /8 20.2 2506 7 /8 /4 7 /8.075 /4 20.22 2507 /8 2 /6.075 /2 0.29 2508 /8 /4 2 7 /6.075 /4 0. 2509 /2.05 2 /4 0.42 250 2 /8 2 /8.05 2 /4 0.50 25 2 5 /8 2 /2 7 /8.05 /4 0.62 252 /8 4 5 /6.05 /4 0.66 254 4 /8 4 5 /2.25 4 /4 0.88 suffix SS to fig. number. Price on request. 246-246 Low carbon steel Electro-galvanized Specify figure number and O.D. tube size. 250-254 A B C D Low carbon steel Western gold Specify figure number and O.D. size. EPDM STOCK: Thickness: /8 Length: 25 ft./box Specify figure number and number of feet. Cushion Material 2600 Service Temp: -70 to 50 F Weight per ft:.02 5/8 /6 45

Strut Nuts 00-0 Low carbon steel Electro-galvanized Specify figure number and thread size. 0- Low carbon steel Electro-galvanized Specify figure number and thread size. 20-20 Low carbon steel Electro-galvanized Strut Nut without Spring Fig. Thread Std. Weight Each Number Size Package Thickness (in Lbs.) 00 #8-2 00 /4.06 002 #0-24 00 /4.06 00 #0-2 00 /4.06 004* /4 00 /4.06 005 5 /6 00 /4.07 006* /8 00 /8.09 007 7 /6 00 /8.09 008* /2 00 /2.2 009 5 /8 00 /2. 00 /4 00 /2. 0 7 /8 00 /2. Available in stainless steel. To order, specify 6 and add *Available in aluminum. To order, add suffix AL to fig. number. Price on request. Strut Nut with Spring Fig. Thread Std. Weight Each Number Size Package Thickness (in Lbs.) 0 #8-2 00 /4.07 02 #0-24 00 /4.07 0 #0-2 00 /4.07 04* /4 00 /4.07 05 5 /6 00 /4.07 06* /8 00 /8.0 07 7 /6 00 /8.0 08* /2 00 /2. 09 5 /8 50 /2.5 0 /4 50 /2.5 7 /8 50 /2.5 Available in stainless steel. To order, specify 6 and add *Available in aluminum. To order, add suffix AL to fig. number. Price on request. Strut Nut with Short Spring Fig. Thread Std. Weight Each Number Size Package Thickness (in Lbs.) 20 #8-2 00 /4.07 202 #0-24 00 /4.07 20 #0-2 00 /4.07 204 /4 00 /4.07 205 5 /6 00 /4.07 206 /8 00 /8.09 207 7 /6 00 /8.09 208 /2 00 /8.09 209 5 /8 50 /8.0 20 /4 50 /8.0 Specify figure number and thread size. 46

Strut Nuts Strut Nut with Long Spring Fig. Thread Std. Weight Each Number Size Package Thickness (in Lbs.) 0 #8-2 00 /4.07 02 #0-24 00 /4.07 0 #0-2 00 /4.07 04 /4 00 /4.07 05 5 /6 00 /4.07 06 /8 00 /8.0 07 7 /6 00 /8.09 08 /2 00 /2. 09 5 /8 50 /2.5 0 /4 50 /2.5 7 /8 50 /2.4 Specify figure number and thread size. Shallow Strut Nut without Spring 0- Low carbon steel Electro-galvanized 5-5 Fig. Thread Std. Weight Each Number Size Package Thickness (in Lbs.) 5 /2 00 /8.09 52 5 /8 00 /8. 5 /4 00 /8.09 Specify figure number and thread size. Low carbon steel Electro-galvanized Squeeze Nut Fig. Thread Std. Wt. Each Number Size Package (in Lbs.) 404 /4 00.07 406 /8 00.0 408 /2 00. 404-408 Specify figure number and thread size. NOTE: Fits all profiles of strut Low carbon steel Electro-galvanized 47

Continuous Concrete Insert 400-4002 " X /8" X 2 Gauge 40-402 " X /6" X 2 Gauge /6 /6 8 8 /8 2 9 /6 /6 2 5 /6 7 /8 Low carbon steel /6 Dia. nail holes Pre-galvanized Available in various lengths. Specify length and figure number. Fig. Length Max. Rec. Wt. Bundle Number (feet) Load/Lbs./ft. Per Foot Qty. 400 0 2000.79 240 4002 20 2000.78 480 Note: Furnished with styrofoam filler. 420-4202 " X " X 2 Gauge 4 7 /8 /6 Dia. nail holes 4 Low carbon steel Pre-galvanized Available in various lengths. Specify length and figure number. Fig. Length Max. Rec. Wt. Bundle Number (feet) Load/Lbs./ft. Per Foot Qty. 40 0 500.4 240 402 20 500.5 480 Note: Furnished with styrofoam filler. 40-402 " X " X 2 Gauge /6 /6 8 8 /8 2 /4 7 /8 4 4 /6 Dia. nail holes Low carbon steel Low carbon steel Pre-galvanized Pre-galvanized Available in various lengths. Specify Available in various lengths. Specify length and figure number. length and figure number. Fig. Length Max. Rec. Wt. Bundle Number (feet) Load/Lbs./ft. Per Foot Qty. Fig. Length Max. Rec. Wt. Bundle Number (feet) Load/Lbs./ft. Per Foot Qty. 40 0 2000.99 240 402 20 2000.99 480 420 0 2000.52 240 4202 20 2000.5 480 Note: Furnished with styrofoam filler. Note: Furnished with styrofoam filler. 7 /8 48

End Caps & Plastic Closures Type A End Caps 4405-4420 Fig. Std. Use With Wt. Each Number Package Fig. Numbers (in Lbs.) 4405 00 000 & 400.0 4406 00 00.05 440 00 700 & 4000.08 4420 00 400 & 4200.08 suffix SS to fig. number. Price on request. Low carbon steel 4440-4470 Type B End Caps /8 Fig. Std. Use With Wt. Each Number Package Fig. Numbers (in Lbs.) 4440 00 4000.5 4450 00 4200.5 4460 00 400.5 4470 00 400.5 /4 2 7 /8 Low carbon steel 4500 Plastic Closure Strip Fig. Std. Wt. Per Foot Number Length (feet) (in Lbs.) 4500 0.4 Plastic Plain 49

Flat Plate Fittings 5000-5004 Square Washer 5005-5009 No Turn Square Washer Fig. Rod Std. Wt. Each Number Size Package (in Lbs.) 5000 /4 00.8 500 /8 00.7 5002 /2 00.7 500 5 /8 00.6 5004 /4 00.6 X Specify figure number and rod size. Fig. Rod Std. Wt. Each Number Size Package (in Lbs.) 5005 /4 00.8 5006 /8 00.7 5007 /2 00.7 5008 5 /8 00.6 5009 /4 00.6 X Specify figure number and rod size. 500-502 2-Hole Splice Plate 50-504 -Hole Splice Plate B B C C Fig. Length Std. Wt. Each Number B C Package (in Lbs.) 500 /2 7 /8 50.7 50 4 5 /8 2 /2 50.50 502 /4 50.4 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end Fig. Length Std. Wt. Each Number B C Package (in Lbs.) 50 5 /8 7 /8 25.55 504 4 7 /8 25.50 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 50

Flat Plate Fittings 505 4-Hole Splice Plate 507 4-Hole Splice Plate /4 7 /4 /2 505 50.75 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 507 50.55 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 509 5-Hole Splice Plate 5020 2-Hole Swivel Plate 9 /8 5 /8 5 /4 509 50.96 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5020 50.56 X HOLE DIM: 9 /6 dia. /6 from end 5

Flat Plate Fittings 502 -Hole Swivel Plate 5025 -Hole Corner Plate /2 5 /8 7 /8 /2 502 50.76 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5025 25.58 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 500 4-Hole Corner Plate 505 4-Hole Tee Plate /2 5 /8 5 /8 /2 500 25.75 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 505 25.75 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 52

Flat Plate Fittings 5040 5-Hole Cross Plate 5045 -Hole Corner Gusset Plate /2 /2 5 /8 5 /8 5040 25.00 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5045 25.70 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5050 4-Hole Corner Gusset Plate 5060 5-Hole Corner Gusset Plate 5 /8 5 /8 /2 5 /8 5050 25.02 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5060 25.45 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5

Flat Plate Fittings 5065 -Hole Tee Gusset Plate 5075 4-Hole Tee Gusset Plate /2 /2 /2 5 /8 5065 25.70 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5075 25.00 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5080 5-Hole Tee Gusset Plate 5085 6-Hole Tee Gusset Plate 5 /8 9 /8 5 /8 /2 5080 25.4 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5085 0.49 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 54

Flat Plate Fittings 5090 6-Hole Cross Gusset Plate 5095 7-Hole Cross Gusset Plate 9 /8 5 /8 9 /8 /2 5090 0.66 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5095 0 2.2 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 55

90 Fittings 50-507 -Hole Angle 50 2-Hole Corner Angle B 2 /4 X 7 /8 Fig. Length Std. Wt. Each Number B Package (in Lbs.) 50 7 /8 50.48 50 5 7 /8 25.8 505 7 7 /8 25.05 507 9 7 /8 25.0 Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 52 2-Hole Corner Angle 50 50.6 X HOLE DIM: 9 /6 dia. /6 from end 55-58 2-Hole Corner Angle B 7 /8 2 /6 7 /8 52 50.7 X HOLE DIM: 9 /6 dia. /6 from end Fig. Length Std. Wt. Each Number B Package (in Lbs.) 55 50.49 56 /2 50.54 58 4 50.6 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 56

90 Fittings 59 No-Turn 2-Hole Corner Angle 520 -Hole Corner Angle /2 2 2 2 5 /6 520 25.58 59 50.40 X X HOLE DIM: 9 /6 dia. /6 from end HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 52 -Hole Corner Angle 522 -Hole Corner Angle 4 /6 5 /6 7 /8 52 25.50 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 522 25.58 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 57

90 Fittings 52 -Hole Corner Angle 50 4-Hole Corner Angle /2 /4 2 4 /6 52 25.58 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 50 25.78 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5 4-Hole Corner Angle 55 4-Hole Corner Angle /6 7 /8 2 /4 /4 5 25.76 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 55 25.7 HOLE DIM: 9 /6 dia. /6 from end on centers 58

90 Fittings 540 & 545 -Hole Offset Bent Angle Fig. 540 Right Fig. 545 Left 54 & 546 -Hole Offset Bent Angle Fig. 54 Right Fig. 546 Left 7 /8 /4 7 /8 /2 Right Hand Shown Right Hand Shown 2 /6 2 /6 540 25.5 545 25.5 HOLE DIM: 9 /6 dia. /6 from end on centers 54 25.5 546 25.5 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 548 -Hole Offset Bent Tee 550 4-Hole Offset Bent Tee 2 5 /8 4 7 /8 2 /6 548 25.7 HOLE DIM: 9 /6 dia. /6 from end 550 25.77 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 59

90 Fittings Fig. 555 Right Fig. 556 Left 555 & 556 4-Hole Offset Bent Tee 560 5-Hole Offset Bent Tee 2 /6 5 /8 2 /6 /4 Right Hand Shown /2 /2 555 25.76 556 25.76 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 565 Universal Shelf Bracket 560 25.00 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 566 Universal Welded Shelf Bracket 4 /8 4 /8 4 /8 4 /8 7 /8 7 /8 565 5.5 HOLE DIM: 9 /6 dia. /6 from end /4 on centers 566 5.5 HOLE DIM: 9 /6 dia. /6 from end /4 on centers 60

90 Fittings 570 & 575 4-Hole Corner Gusset 57 & 576 4-Hole Corner Gusset Fig. 570 Right Fig. 575 Left Fig. 57 Right Fig. 576 Left 5 /6 /2 /2 4 /6 Right Hand Shown 7 /8 Right Hand Shown 570 25.00 575 25.00 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 580 -Hole Gussetted Shelf Angle 57 25.00 576 25.00 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 585 4-Hole Gussetted Shelf Angle /2 /2 2 5 /6 4 /6 580 25.72 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 585 25.02 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 6

90 Fittings 586 4-Hole Gussetted Shelf Angle 590 5-Hole Gussetted Shelf Angle 5 /8 5 /8 4 /8 5 /6 586 25.48 590 0.98 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5200 4-Hole Joint Angle Connector 5205 5-Hole Joint Angle Connector /2 /2 /2 /2 2 /4 4 /6 5200 25.00 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5205 20. HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 62

90 Fittings Fig. 520 Right Fig. 52 Left 520 & 52 6-Hole Gussetted Corner Connector /4 5220 2-Hole Adjustable Corner Angle 2 5 /8 9 /6 4 /6 /2 X 9 /6 Slot 2 5 /8 Right Hand Shown 520 5 2.29 52 5 2.29 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 522 2-Hole Adjustable Corner Angle 5220 25.42 X HOLE DIM: 9 /6 dia. /6 from end 5225 2-Hole Adjustable Corner Angle 2 5 /8 2 /8 9 /6 /2 X 9 /6 Slot 6 7 /8 2 9 /6 X 9 /6 Slot 7 /8 522 25.6 X HOLE DIM: 9 /6 dia. /6 from end 5225 25.85 X HOLE DIM: 9 /6 dia. /6 from end 6

90 Fittings 5226 2-Hole Adjustable Corner Angle 5228 2-Hole Adjustable Corner Angle 2 /8 /2 2 /4 4 7 /8 /2 /2 2 9 /6 X 9 /6 Slot 2 9 /6 X 9 /6 Slot 7 8 5226 25.58 X HOLE DIM: 9 /6 dia. /6 from end 520 -Hole Adjustable Corner Angle 5228 25.97 HOLE DIM: 9 /6 dia. /6 from end 5250 4-Hole Adjustable Corner Angle 2 5 /8 /2 X 9 /6 Slots /2 X 9 /6 Slot 7 /8 /4 4 6 5 /8 7 /8 520 25.59 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5250 0.90 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 64

90 Fittings 5255 4-Hole Adjustable Corner Angle 5260 2-Hole Tapped Corner Angle 5 /6-8 Tapped /2 X 9 /6 Slots 7 /8 /4 8 5 /8 6 7 /8 5255 0 2.56 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5260 50. X HOLE DIM: 9 /6 dia. /6 from end 5270 2-Hole Bus Duct Angle /2 7 /8 2 5270 50.7 X HOLE DIM: 9 /6 dia. 65

Angle Fittings 50-55 2 /6 B o /4 2-Hole Open Angle Connector Fig. Angle Std. Wt. Each Number B o Package (in Lbs.) 50 7 /2 25.58 502 5 25.58 50 22 /2 25.58 504 0 25.58 506 7 /2 25.58 507 52 /2 25.58 508 60 25.58 509 67 /2 25.58 50 75 25.58 5 82 /2 25.58 55 45 25.58 X Specify figure number and angle B. HOLE DIM: 9 /6 dia. /6 from end 540-550 4-Hole Open Angle Connector /2 B o /2 Fig. Angle Std. Wt. Each Number B o Package (in Lbs.) 540 7 /2 25.78 54 5 25.78 542 22 /2 25.78 54 0 25.78 544 7 /2 25.78 545 45 25.78 546 52 /2 25.78 547 60 25.78 548 67 /2 25.78 549 75 25.78 550 82 /2 25.78 X Specify figure number and angle B. HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 66

Angle Fittings 2-Hole Closed Angle Connector Fig. Angle Std. Wt. Each Number B o Package (in Lbs.) 560 7 /2 25.58 56 45 25.58 562 52 /2 25.58 56 60 25.58 564 67 /2 25.58 565 75 25.58 566 82 /2 25.58 560-566 B o /4 2 /4 X Specify figure number and angle B. HOLE DIM: 9 /6 dia. /6 from end 4-Hole Closed Angle Connector Fig. Angle Std. Wt. Each Number B o Package (in Lbs.) 570 7 /2 25.95 57 45 25.95 572 52 /2 25.95 57 60 25.95 574 67 /2 25.95 575 75 25.95 576 82 /2 25.95 570-576 B 4 9 o /6 4 9 /6 X Specify figure number and angle B. HOLE DIM: 9 /6 dia. /6 from end 67

Braces 540-542 B X 2-Hole 45 Knee Brace Fig. Length Std. Wt. Each Number B Package (in Lbs.) 540 2 5.60 54 6 Bulk 2.8 542 8 Bulk 2.80 Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 5420-5427 B /4 2-Hole 45 Tubing Knee Brace Fig. Length Std. Wt. Each Number B Package (in Lbs.) 5420 8 Bulk.45 542 24 Bulk.86 5422 0 Bulk 2.25 542 6 Bulk 2.66 5424 42 Bulk.07 5425 48 Bulk.48 5426 54 Bulk.89 5427 60 Bulk 4.0 Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 540-5440 B 2-Hole Straight Tubing Brace Fig. Length Std. Wt. Each Number B Package (in Lbs.) 540 8 Bulk. 54 24 Bulk.74 542 0 Bulk 2.5 54 6 Bulk 2.56 544 42 Bulk 2.95 545 48 Bulk.5 546 54 Bulk.80 547 60 Bulk 4.20 548 72 Bulk 5.00 549 84 Bulk 5.85 5440 96 Bulk 6.70 Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 68

U Fittings 550 -Hole U Support 550 5-Hole U Support /6 5 /2 5 /8 550 25.66 X HOLE DIM: 9 /6 dia. /6 from end 550 25.85 X HOLE DIM: 9 /6 dia. /6 from end 5505 -Hole U Support 5507 -Hole U Support 2 7 /6 /4 5 /2 5 /2 5505 25.08 X HOLE DIM: 9 /6 dia. /6 from end 5507 0.25 X HOLE DIM: 9 /6 dia. /6 from end 69

U Fittings 5509 -Hole U Support 55 -Hole U Support 7 /8 4 7 /8 5 /8 5 /2 5509 0.57 55 25.95 X HOLE DIM: 9 /6 dia. /6 from end X HOLE DIM: 9 /6 dia. /6 from end 557 5-Hole U Support 9 /6 dia. Hole 552 6-Hole U Support /4 7 /6 dia. (4) Holes 7 /4 /8 557 25.5 7 Ga. HOLE DIM: 9 /6 dia. /6 from end 552 0.04 X HOLE DIM: 9 /6 dia. /6 from end 70

U Fittings 550-552 Slotted -Hole U Support 554 Stud Ring Connector 2 /2 2 /2 B /2 X 9 /6 Slots Fig. Length Std. Wt. Each Number B Package (in Lbs.) 550 7 /4 0.96 55 8 /2 0. 552 0 /8 0.29 X HOLE DIM: 9 /6 dia. 554 25.5 HOLE DIM: 9 /6 dia. 5542 2 Stud Ring Connector 554 2 Stud Ring Connector 2 /2 2 /2 2 /2 2 /2 5542 25.59 554 25.59 HOLE DIM: 9 /6 dia. HOLE DIM: 9 /6 dia. 7

Z Fittings 5550 2-Hole Offset Z Support 555 2-Hole Z Support For #200 Strut 2 /8 /2 /2 /6 5550 25.55 X HOLE DIM: 9 /6 dia. /6 from end 555 50.47 X HOLE DIM: 9 /6 dia. /6 from end 5552 -Hole Z Support For #500 Strut 555 2-Hole Z Support For #600 Strut /2 /2 /2 2 7 /6 5552 25.70 X HOLE DIM: 9 /6 dia. /6 from end 555 25.67 X HOLE DIM: 9 /6 dia. /6 from end 72

Z Fittings 5554 -Hole Z Support For #000 Strut 5556 2-Hole Offset Z Support /4 /2 5 /2 5554 50.5 X HOLE DIM: 9 /6 dia. /6 from end 5556 25.8 X HOLE DIM: 9 /6 dia. /6 from end 5558 2-Hole Z Support /2 5560-5562 2 Hole Z Bus Duct Connection 4 7 /8 /2 /2 B 5558 25.90 X HOLE DIM: 9 /6 dia. /6 from end Fig. Length Std. Wt. Each Number B Package (in Lbs.) 5560 4 /4 25.89 556 25 /2 25.78 5562 2 /2 25.62 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 7

Z Fittings 5565 Tapped Z Support 5570-5574 2-Hole Z Support /2 B 5 /6-8 Tapped Hole 5565 25.5 X HOLE DIM: 9 /6 dia. /6 from end Fig. Length Std. Wt. Each Number B Package (in Lbs.) 5570 4 25.77 557 5 25.95 5572 6 25.98 557 7 25.05 5574 8 25.20 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 5575 -Hole Sheath Corner Connection 5580 Channel Hanger For #000 Strut /2 /6 9 /2 Dia. Hole /2 5575 25.68 X HOLE DIM: 9 /6 dia. /6 from end 5580 00.09 Ga. 74

Z Fittings 558 Channel Hanger For #200 Strut 5582 Channel Hanger For #500 Strut /6 /6 9 /2 Dia. Hole /6 9 /2 Dia. Hole /4 558 00.07 Ga. 5582 00. Ga. 558 Channel Hanger For #600 Strut 5590 Adjustable Offset Gussetted Z Support /2 5 /2 7 /8 2 9 /6 X 9 /6 Slot /6 7 /8 7 /8 9 /2 Dia. Hole 2 7 /6 558 00. Ga. 5590 0.02 HOLE DIM: 9 /6 dia. /6 from end 75

Wing Fittings Fig. 5600 Right Fig. 560 Left 5600 & 560 -Hole Corner Connector Fig. 5605 Right Fig. 5606 Left 5605 & 5606 4-Hole Corner Connector 2 /6 2 /6 Right Hand Shown Right Hand Shown /6 /2 /4 5600 25.60 560 25.60 X HOLE DIM: 9 /6 dia. /6 from end 5605 25.70 5606 25.70 X HOLE DIM: 9 /6 dia. /6 from end Fig. 560 Right Fig. 56 Left 560 & 56 5-Hole Corner Connector Fig. 565 Right Fig. 566 Left 565 & 566 6-Hole Corner Connector 5 /6 /2 5 /6 /2 Right Hand Shown 5 /8 Right Hand Shown 560 25.00 56 25.00 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 565 25.20 566 25.20 X HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 76

Wing Fittings 5620 4-Hole Double Corner Connector 5625 6-Hole Double Corner Connector 2 /6 5 /6 /2 5620 25.76 HOLE DIM: 9 /6 dia. /6 from end 560 8-Hole Double Corner Connector /2 5625 25.5 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 565 5-Hole Double Wing Connector /2 5 /6 2 /6 5 /8 560 0.55 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5 7 /6 565 5.9 HOLE DIM: 9 /6 dia. /6 from end 77

Wing Fittings 5640 8-Hole Double Wing Connector 5645 0-Hole Double Wing Connector 5 /6 5 /6 2 5 /2 2 5 /2 5 7 /6 5640 0.77 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5650 6-Hole Triple Wing Connector 9 /8 5645 0 2.02 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5655 2-Hole Triple Wing Connector 2 /6 /4 5 /6 2 5 /2 5 /2 5650 0.07 HOLE DIM: 9 /6 dia. /6 from end 2 5 /2 9 /6 5655 0 2.9 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 78

Wing Fittings 5660 9-Hole Triple Wing Connector 5665 8-Hole Gussetted Double Corner Connector 5 7 /6 5 /6 4 2 5 /2 5660 0.9 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 4 5665 5 2.7 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5675 0-Hole Gussetted Double Corner Connector 5685 8-Hole Gussetted Double Corner Connector 9 /6 /2 7 /8 4 2 5 /2 5675 5 2.85 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 4 5685 5 4.70 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 79

Clevis Fittings 5700-5704 -Hole U Washer 5705 2-Hole Splice Clevis For #200 Strut Hole Size A /2 /4 Fig. Hole Size Std. Wt. Each Number Size A Package (in Lbs.) 5700 /4 5 /6 00.8 570 /8 7 /6 00.8 5702 /2 9 /6 00.8 570 5 /8 /6 00.8 5704 /4 /6 00.7 0 gauge 5705 20.78 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 570 -Hole Splice Clevis For #200 Strut 575 4-Hole Splice Clevis For #200 Strut 5 /8 7 /4 570 20.25 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 575 20.75 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 80

Clevis Fittings 5720 2-Hole Splice Clevis For #000 Strut 570 4-Hole Splice Clevis For #000 Strut /2 7 /4 5720 20.9 570 0 2.68 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 5750-5752 2-Hole Clevis 5760-5764 2-Hole Clevis /6 /2 7 /8 7 /8 B B /6 /6 Fig. Length Std. Wt. Each Number B Package (in Lbs.) 5750 2 /2 25.57 575 25 /2 25.7 5752 4 /4 25.84 Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end Fig. Length Std. Wt. Each Number B Package (in Lbs.) 5760 4 25.78 576 5 25.89 5762 6 25.07 576 7 25.2 5764 8 25.24 Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 8

Clevis Fittings 5770 -Hole Clevis 5775 -Hole Suspension Clevis 7 /8 7 /6 5 /6 29 /2 2 /2 7 /8 5770 25.75 HOLE DIM: 9 /6 dia. /6 from end 5775 25.75 X HOLE DIM: 9 /6 dia. /6 from end 5780 4-Hole Suspension Clevis 7 /8 5 /6 2 /2 5780 20.7 X HOLE DIM: 9 /6 dia. /6 from end 82

Miscellaneous Fittings 580 & 5802 Single Pipe Axle Support for /4" Pipe 580 & 5804 Single Pipe Axle Support for 2" Pipe Fig. 580 Right Fig. 5802 Left Fig. 580 Right Fig. 5804 Left 5 /8 5 /8 Right Hand Shown 5 /8 Right Hand Shown 580 0 2.25 5802 0 2.25 HOLE DIM: 9 /6 dia. /6 from end 580 0 2.46 5804 0 2.46 HOLE DIM: 9 /6 dia. /6 from end 582 Pipe Support Bracket 5825-5827 Series Ladder Rungs /2 B 4 582 20.88 X HOLE DIM: 9 /6 dia. /6 from end Fig. Length Std. Wt. Each Number B Package (in Lbs.) 5825 2 0.76 5826 5 0 2.02 5827 8 bulk 2.4 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end 8

Brackets & Trolleys 580-584 Wall Ladder Brackets 585-587 Pipe Coupling Fitting C A B 2 2 /6 5 /8 Fig. Length Std. Wt. Each Number A B C Package (in Lbs.) 580 7 5 /8 6 2 /8 0.0 58 9 5 /8 8 4 /8 0.64 582 0 6 /8 0 2.00 58 2 8 /8 0 2.5 584 5 5 /8 4 0 /8 bulk.8 X Specify figure number and length B. HOLE DIM: 9 /6 dia. /6 from end Fig. Pipe Std. Wt. Each Number Size Package (in Lbs.) 585 /2 0.77 586 /4 0.84 587 0.05 X Specify figure number and pipe size. HOLE DIM: 9 /6 dia. /6 from end 5840 Trolley Beam Support 5845 Trolley Beam Joint Support () 9 /6 Dia. Hole 5 /6 () 9 /6 Dia. Hole 5 /6 2 /8 2 /8 (2) 7 /6 Dia. Holes (6) 7 /6 Dia. Holes /2 /2 /2 /2 2 /2 /2 Design Load (in Lbs.) 5840 25.02 200 Design Load (in Lbs.) 5845 5 2.20 2500 84

Brackets & Trolleys 5860 45 Stair Support 586 7 /2 Stair Support 7 /8 7 /8 /6 /6 45 o 7 /2 o /2 /2 8 7 /8 /4 8 7 /8 /4 /2 /2 /6 /6 5860 0 2.20 X 5870 4-Bearing Trolley Assembly 586 0 2.06 X 5875 2 Bearing Trolley Assembly /2 /4 5870 0.0 5875 25.48 Design Load FPM RPM (in Lbs.) 80 600 00 90 00 450 0 00 600 Design Load based on use with PHD 000 Series Strut Channel Design Load FPM RPM (in Lbs.) 80 600 50 90 00 225 0 00 47 Design Load based on use with PHD 000 Series Strut Channel HOLE DIM: 9 /6 dia. HOLE DIM: 9 /6 dia. 85

Post Bases 6005 Post Base for Strut 600 Post Base for Strut (4) Holes /4 Dia. (4) Holes /4 Dia. 6 6 4 /4 6 4 /4 6 6005 0.4 HOLE DIM: 9 /6 dia. 605 Post Base for Strut 600 0.4 HOLE DIM: 9 /6 dia. 6020 Post Base for Strut (2) Holes /4 Dia. (4) Holes /4 Dia. /2 6 6 /4 8 /8 6 605 0 2.0 6020 0.92 HOLE DIM: 9 /6 dia. HOLE DIM: 9 /6 dia. 86

Post Bases 6025 Post Base for Strut 600 Post Base for Strut (4) Holes /4 Dia. /2 (2) Holes /4 Dia. /2 6 4 /4 4 /4 6 6 /4 8 /8 6025 0.92 600 0.2 HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 605 Post Base for Double Strut HOLE DIM: 9 /6 dia. /6 from end 7 /8 on centers 6040 Post Base for Double Strut (4) Holes /4 Dia. 6 (4) Holes /4 Dia. 6 605 0.0 HOLE DIM: 9 /6 dia. /6 from end 6 4 /4 4 /4 6 6040 0.0 HOLE DIM: 9 /6 dia. /6 from end 87

Post Bases 6045 Post Base for Double Strut 6050 Post Base for Double Strut (2) Holes /4 Dia. (4) Holes /4 Dia. /2 6 6 /4 8 /8 6 6045 0 2.50 HOLE DIM: 9 /6 dia. /6 from end 6060 Post Base for Double Strut 6050 0 4.00 HOLE DIM: 9 /6 dia. /6 from end 6065 Post Base for Double Strut (4) Holes /4 Dia. (2) Holes /4 Dia. /2 /2 4 /4 6 6 /4 4 /4 6 8 /8 6060 0 4.00 HOLE DIM: 9 /6 dia. /6 from end 6065 0.20 HOLE DIM: 9 /6 dia. /6 from end 88

Post Bases 6080 Post Base for 5 8 Back to Back Strut 6095 Post Base for 5 8 Strut (4) Holes 7 /6 Dia. /2 /6 /6 5 /2 5 6080 0.0 6095 0 2.97 HOLE DIM: 9 /6 dia. /6 from end HOLE DIM: 9 /6 dia. 89

Brackets /6 C /4 6 /8 B 60-622 Shelf Bracket 60 622 Fig. Length Uniform Load Std. Wt. Each Number B C (in Lbs.) Package (in Lbs.) 60 8 /2 4 800 0.68 602 0 /2 4 800 0 2.02 62 2 /2 6 900 Bulk 2.58 622 4 /2 6 900 Bulk 2.95 Note: Load based on use with 2 ga. strut. Specify figure number and length B. 60-65 Single Channel Bracket /6 /6 /4 /6 /4 /4 /4 2 4 /8 602 /4 /4 /8 /4 62 /8 7 /4 /6 C 62-625 Shelf Bracket B /6 /4 /6 /4 /6 /4 625 Fig. Fig. Length Length Uniform Load Uniform Load Std. Wt. Each Number B B C C (in Lbs.) (in Lbs.) Package (in Lbs.) 62 6 /2 6 200 Bulk 4.05 624 8 /2 6 070 Bulk 4.68 625 20 /2 6 600 Bulk 4.90 Note: Load based on use with 2 ga. strut. Bulk packaging. Specify figure number and length B. 5 /4 /8 62 5 /4 /8 5 /4 7 /4 7 /4 624 /8 7 /4 640-644 Double Channel Bracket /6 2 /8 4 5 /8 B 6 /4 4 5 /8 B Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 60 6 200 0.85 6 9 900 0.95 62 2 600 0 2.9 6 4 500 Bulk.20 64 8 400 Bulk 4.0 65 24 00 Bulk 5.09 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 640 2 2000 Bulk 5.05 64 8 00 Bulk 7.0 642 24 000 Bulk 9.5 64 0 800 Bulk.20 644 6 650 Bulk.25 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. 90

Brackets 650-652 Braced Single Bracket 660-672 Braced Single Bracket 8 /4 B C B Right Hand Shown Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) Fig. Fig. Length Length Uniform Load Uniform Load Std. Wt. Each 650 2 600 5.88 Number B B C C (in Lbs.) (in Lbs.) Package (in Lbs.) 65 8 850 Bulk 5.06 660 24 6 7 /6 225 Bulk.70 652 24 850 Bulk 7.20 66 26 6 5 /6 225 Bulk 4.25 PHD 400 Series " profile 2 ga. strut channel used to fabricate this product. 662 28 7 7 /6 225 Bulk 4.80 66 0 7 5 /6 225 Bulk 5.20 664 2 7 /6 275 0.4 665 4 5 /6 275 Bulk.62 666 6 4 7 /6 275 Bulk 2.04 Specify figure number and length B. 667 8 4 5 /6 275 Bulk 2.2 HOLE DIM: 9 /6 dia. 668 20 5 7 /6 250 Bulk 2.75 669 22 5 5 /6 250 Bulk.7 670 6 5 /6 275 0.58 67 8 2 7 /6 275 0.82 672 0 2 5 /6 275 0.0 Note: Load based on use with 2 ga. strut. 6202-6208 Interlocking Channel Bracket (Slot Up) /2 /4 2 Ga. Specify figure number, R or L and length B B Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 6202 6 200 0.50 6204 2 600 0 2.50 6206 8 400 Bulk.50 6208 24 00 Bulk 4.50 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. 9

Brackets 622-628 Interlocking Channel Bracket (Slot Down) 6222 & 6224 Wrap-Around Channel Bracket (Slot Up) /2 /2 B /2 B Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 622 6 200 0.50 624 2 600 0 2.50 626 8 400 Bulk.50 628 24 00 Bulk 4.50 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. 622 & 624 Wrap-Around Channel Bracket (Slot Down) Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 6222 6 600 0.90 6224 2 800 0 2.75 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. 6246 & 6248 Wrap-Around Channel Bracket (Slot Up) /2 B 5 /8 B Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 622 6 600 0.90 624 2 800 0 2.75 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. Fig. Length Uniform Load Std. Wt. Each Number B (in Lbs.) Package (in Lbs.) 6246 8 600 Bulk 4.0 6248 24 450 Bulk 5.0 Note: Load based on use with 2 ga. PHD 000 series strut channel. Specify figure number and length B. HOLE DIM: 9 /6 dia. 92

Brackets 605 Single Channel Bracket Support For 00 & 0 Strut 60 Double Channel Bracket Support For 00A & 0A Strut Note: Load is in in.-lbs. and applies to fitting only, not strength of strut arm. Load rating is based on use with 2 gauge strut. If 4 gauge strut is used, load is reduced to 4400 in.-lbs. 5 7 /8 4 /4 Note: Load is in in.-lbs. and applies to fitting only, not strength of strut arm. Load rating is based on use with 2 gauge strut. If 4 gauge strut is used, load is reduced to 900 in.-lbs. 7 /2 4 /4 Fig. Uniform Load Std. Wt. Each Number in. - Lbs. Package (in Lbs.) 605 600 0 2.0 HOLE DIM: 9 /6 dia. Fig. Uniform Load Std. Wt. Each Number in. - Lbs. Package (in Lbs.) 60 000 0 2.66 HOLE DIM: 9 /6 dia. Beam Clamps 700 & 7002 Heavy Duty Beam Clamp Continuous Weld 7005-7007 Beam Clamp B 5 /8" /4" 2 /2" A Tapped Hole Size Note: Includes Set Screw. Fig. Material Set Max. Rec. Std. Wt. Each Number A Size Screw Load/Lbs. Package (in Lbs.) 700 /8 /6 /2 X 2 00 0.56 7002 /2 /4 /2 X 2 900 0 2.0 For beams between /4" & " thick flanges Fig. Material Std. Wt. Each Number Size A B C D E Package (in Lbs.) 7005 /4-20 5 /6 /4 00.25 7006 /8-6 5 /6 /4 00.25 7007 2 /8-6 /2 /8 2 2 0.95 C E D A 700 & 7002 - Low carbon steel 7005-7007 - Malleable iron 9

Beam Clamps 70 & 702 I Beam Clamp 7020 & 7025 I Beam Clamp *Max. load when used in pairs. *Max. load when used in pairs. /6 B /4 " Max. Flange Thickness Fig. Material Set Std. Max. Rec. Wt. Each Number Size Screw Package Load/lbs. (in Lbs.) 70 /4 702 /8 /8 50 450*.26 /2 25 900*.64 Note: Includes Set Screw. 9 /6 Hole Furnished on 7025 only C 2 Fig. Std. Max. Rec. Wt. Each Number B C Package Load/lbs. (in Lbs.) 7020 2 /8 25 900*.72 7025 2 /2 /2 25 500*.94 Note: Includes Set Screw. /8 700 Z Beam Clamp *Max. load when used in pairs. 7040 Beam Clamp *Max. load when used in pairs. 5 /8 /4 " Max. Flange Thickness 27 /2 Fig. Set Std. Max. Rec. Wt. Each Number Screw Package Load/lbs. (in Lbs.) 700 /2 25 450*.6 Note: Includes Set Screw. Order /2" - X /4 HHCS and Strut Nut Separately /8 Fig. Std. Max. Rec. Wt. Each Number Package Load/lbs. (in Lbs.) 7040 50 600*.26 Note: Order /2" - X /4 HHCS and Strut Nut Separately X 94

Beam Clamps 2 /2 7050 & 705 Square U-Bolt /8"-6 Hex Nuts Included 2 /2 7060 Beam Clamp For use with Strut *Max. load when used in pairs. /8"-6 Threads /2 /4 /4 Fig. Length Std. Wt. Each Number B Package (in Lbs.) Fig. Set Std. Max. Rec. Wt. Each 7050 /8 25.25 Number Screw Package Load/lbs. (in Lbs.) 705 5 25. 7060 /2 25 500*.07 /2 Low carbon steel 7070 Beam Clamp For use with Strut 2 /8 *Max. load when used in pairs. 7075 Beam Clamp For use with /4 Strut 2 /8 *Max. load when used in pairs. /8 5 /8 Dia. Fig. Std. Max. Rec. Wt. Each Number Package Load/Lbs. (in Lbs.) /8 Dia. Fig. Std. Max. Rec. Wt. Each Number Package Load/Lbs. (in Lbs.) 7070 25 000*.80 7075 25 000*.88 95

Pipe Clamps 72-728 One Hole Clamp For O.D. Tubing 770 Pipe Stop B /2 7 /6 Fig. Tubing Std. Wt. Each Number O.D. B Package (in Lbs.) 72 /4 /6 00.0 722 5 /6 /8 00.0 72 /8 /8 00.04 724 /2 /6 00.04 725 5 /8 /4 00.05 726 /4 5 /6 00.06 727 7 /8 /8 00.06 728 7 /6 00.07 4 Ga. Specify figure number and O.D. size. 770 50.8 725-726 Standard Pipe Strap Y Z C X B Max. Rec. Fig. Pipe Std. Material Loads (in Lbs.) Wt. Each Number Size B C Package Size X Y Z (in Lbs.) 725 /2 2 7 /8 7252 /4 /6 725 /2 7254 /4 /6 7255 /2 5 /6 7256 2 5 /6 7257 2 /2 6 /6 7258 6 /6 7259 /2 7 5 /6 7260 4 8 726 5 9 7262 6 0 /8 726 8 2 5 /6 25 5 /6 25 5 /6 25 5 /6 25 5 /6 25 7 /6 0 7 /6 0 7 /6 0 7 /6 0 7 /6 0 7 /6 0 7 /6 0 7 /6 5 /8 05 50 600.29 /8 05 50 600.2 /8 20 50 600.5 /8 20 50 600.4 /8 20 50 600.45 /4 80 480 200.00 /4 80 480 200. /4 00 480 200.2 /4 00 480 200.5 /4 450 600 500.66 /4 450 600 500.9 /4 450 600 500 2.2 /4 600 800 2000 2.97 Low carbon steel Electro-galvanized Specify figure number and pipe size. Available in stainless steel. To order, specify 04 or 6 and add suffix SS to fig. number. Price on request. 96

Pipe Rollers 7400 Separate Rollers 750-7506 Pipe Roller with Axle Fig. For Pipe Std. Wt. Each Number Sizes Package (in Lbs.) 7400 /2 X 8 0 pr. 2.80 Cast Aluminum Rolls w/steel bracket. Fig. For Pipe Std. Wt. Each Number Sizes Package (in Lbs.) 750-0.59 7502-4 0.66 750 4-6 0.79 7504 6-8 0.82 7505 0 0.90 7506 2 0.9 Cast Alum. Rolls w/steel bracket and axle. Specify figure number and pipe size. 750 60 Separate Rollers 7560 60 Rollers with Center Roller Fig. For Pipe Std. Wt. Each Number Sizes Package (in Lbs.) 750 6-8 5 sets.97 Cast Aluminum Rolls w/steel bracket. Fig. For Pipe Std. Wt. Each Number Sizes Package (in Lbs.) 7560 20-0 5 sets 8.8 Cast Aluminum Rolls w/steel bracket. 97