www.cranepumps.com Series 4XSHD 18 Frame Driver Specifications: DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accommodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE... Cast Iron ASTM A-48, Class 30 WEAR RING... C954 Lead-Free Bronze MOTOR HOUSING... Cast Iron ASTM A-48, Class 30 SEAL PLATE... Cast Iron ASTM A-48, Class 30 IMPELLER: Design... Enclosed Dual Vane, With Pump Out Vanes on Back Side. Dynamically Balanced ISO G6.3 Material... Ductile Iron ASTM A-536, 65-45-12 SHAFT... 416 Stainless Steel O RINGS... Buna-N HARDWARE... 300 Series Stainless Steel LIFTING BAIL... 300 Series Stainless Steel PAINT SEAL:... Axalta Corlar Epoxy, Two Coats Design... Tandem Mechanical, Oil Filled Reservoir. Material: Inboard... Rotating Faces - Carbon Stationary Faces - Ceramic Material: Outboard... Rotating Faces - Silicon Carbide Stationary Faces - Silicon Carbide Elastomer - Buna-N Hardware - 300 Series Stainless CORD ENTRY... Custom Molded, Quick Connected for Sealing and Strain Relief POWER CORD... CSA Certifi ed Submersible Power Cable 2000V - Ordered Separately SPEED... 1750 RPM UPPER BEARING: Design... Single Row, Ball, Oil Lubricated Load... Radial LOWER BEARING: Design... Double Row, Ball, Oil Lubricated Load... Radial & Thrust MOTOR: Design... NEMA B - Three Phase Torque Curve NEMA L - Single Phase Torque Curve Oil-Filled, Squirrel Cage Induction, Inverter Duty rated per NEMA MG1 Insulation... Class H Varnish & Magnet Wire SINGLE PHASE... Requires overload protection to be included in control panel. Requires start components to be included in panel. Provided with pump. THREE PHASE... Requires overload protection to be included in control panel. MOISTURE SENSOR... Normally Open (N/O), Requires Relay in Control Panel TEMPERATURE SENSOR... Three Normally Closed (N/C). To be wired in series with control circuit. OPTIONAL EQUIPMENT... Seal Material, Impeller Trims, Cord Length, Leg Kit MARKINGS... CSA WEIGHT... 228 lbs (104 Kg) NOISE EMISSION MAX... In-Air 65 db-a SUBMERGENCE... Max Depth 66ft (20m) RECOMMENDED: Accessories... Break Away Fitting (BAF) Check Valve Control Panel Series: 4XSHD 3-10HP, 1750RPM, 60Hz Explosion Proof, Class I, Division 1, Groups C & D, T4 C Canadian Standards Association File No. LR16567 US This product may be covered by one or more of the following patents and other patent(s) pending: US Patent 7,931,473 Sample Specifi cations: Section Page H. DESCRIPTION: SUBMERSIBLE NON-CLOG SEWAGE PUMP DESIGNED FOR RAW SEWAGE APPLICATIONS. 43 3/18
Series 4XSHD 21 Frame Driver www.cranepumps.com Specifications: Series: 4XSHD 15-30HP, 1750RPM, 60Hz 7.5-30HP, 1150RPM, 60Hz Explosion Proof, Class I, Division 1, Groups C & D, T4 C Canadian Standards Association File No. LR16567 US This product may be covered by one or more of the following patents and other patent(s) pending: US Patent 7,931,473 Sample Specifi cations: Section Page H. DESCRIPTION: SUBMERSIBLE NON-CLOG SEWAGE PUMP DESIGNED FOR RAW SEWAGE APPLICATIONS. DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accommodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE... Cast Iron ASTM A-48, Class 30 WEAR RING... C954 Lead-Free Bronze MOTOR HOUSING... Cast Iron ASTM A-48, Class 30 SEAL PLATE... Cast Iron ASTM A-48, Class 30 IMPELLER: Design... Enclosed Dual Vane, With Pump Out Vanes on Back Side. Dynamically Balanced ISO G6.3 Material... Ductile Iron ASTM A-536, 65-45-12 SHAFT... 416 Stainless Steel O RINGS... Buna-N HARDWARE... 300 Series Stainless Steel LIFTING BAIL... 300 Series Stainless Steel PAINT SEAL:... Axalta Corlar Epoxy, Two Coats Design... Tandem Mechanical, Oil Filled Reservoir. Material: Inboard... Rotating Faces - Carbon Stationary Faces - Ceramic Material: Outboard... Rotating Faces - Silicon Carbide Stationary Faces - Silicon Carbide Elastomer - Buna-N Hardware - 300 Series Stainless CORD ENTRY... Custom Molded, Quick Connected for Sealing and Strain Relief POWER CORD... CSA Certifi ed Submersible Power Cable 2000V - Ordered Separately SPEED... 1750 or 1150 RPM UPPER BEARING: Design... Single Row, Ball, Oil Lubricated Load... Radial LOWER BEARING: Design... Double Row, Ball, Oil Lubricated Load... Radial & Thrust MOTOR: Design... NEMA B Three Phase Torque Curve. Oil-Filled, Squirrel Cage Induction, Inverter Duty rated per NEMA MG1 Insulation... Class H Varnish & Magnet Wire THREE PHASE... Requires overload protection to be included in control panel. MOISTURE SENSOR... Normally Open (N/O), Requires Relay in Control Panel TEMPERATURE SENSOR... Three Normally Closed (N/C). To be wired in series with control circuit. OPTIONAL EQUIPMENT... Seal Material, Impeller Trims, Cord Length, Leg Kit MARKINGS... CSA WEIGHT... 634 lbs (288 Kg) NOISE EMISSION MAX... In-Air 73 db-a SUBMERGENCE... Max Depth 66ft (20m) RECOMMENDED: Accessories... Break Away Fitting (BAF) Check Valve Control Panel 44 3/18
www.cranepumps.com Series 4XSHD 28 Frame Driver Specifications: DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accommodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE... Cast Iron ASTM A-48, Class 30 WEAR RING... C954 Lead-Free Bronze MOTOR HOUSING... Cast Iron ASTM A-48, Class 30 SEAL PLATE... Ductile Iron ASTM A-536, 65-45-12 IMPELLER: Design... Enclosed Dual Vane, With Pump Out Vanes on Back Side. Dynamically Balanced ISO G6.3 Material... Ductile Iron ASTM A-536, 65-45-12 SHAFT... 416 Stainless Steel O RINGS... Buna-N HARDWARE... 300 Series Stainless Steel LIFTING BAIL... 300 Series Stainless Steel PAINT SEAL:... Axalta Corlar Epoxy, Two Coats Design... Tandem Mechanical, Oil Filled Reservoir. Material: Inboard... Rotating Faces - Carbon Stationary Faces - Ceramic Material: Outboard... Rotating Faces - Silicon Carbide Stationary Faces - Silicon Carbide Elastomer - Buna-N Hardware - 300 Series Stainless CORD ENTRY... 50 ft. (12.1m) Cord. Rigid quick change epoxy-potted housing POWER CORD... CSA Certifi ed Submersible Power Cable 2000V - Ordered Separately SPEED... 1750 or 1150 RPM UPPER BEARING: Design... Single Row, Ball, Oil Lubricated Load... Radial LOWER BEARING: Design... Double Row, Ball, Oil Lubricated Load... Radial & Thrust MOTOR: Design... NEMA B Three Phase Torque Curve. Oil-Filled, Squirrel Cage Induction, Inverter Duty rated per NEMA MG1 Insulation... Class H Varnish & Magnet Wire THREE PHASE... Requires overload protection to be included in control panel. MOISTURE SENSOR... Normally Open (N/O), Requires Relay in Control Panel TEMPERATURE SENSOR... Three Normally Closed (N/C). To be wired in series with control circuit. OPTIONAL EQUIPMENT... Seal Material, Impeller Trims, Cord Length, Leg Kit MARKINGS... CSA WEIGHT... 842 lbs (382 Kg) SUBMERGENCE... Max Depth 66ft (20m) RECOMMENDED: Accessories... Break Away Fitting (BAF) Check Valve Control Panel Series: 4XSHD 20-60HP, 1750RPM, 60Hz 20-40HP, 1150RPM, 60Hz Explosion Proof, Class I, Division 1, Groups C & D, T4 C Canadian Standards Association File No. LR16567 US Sample Specifi cations: Section Page H. DESCRIPTION: SUBMERSIBLE NON-CLOG SEWAGE PUMP DESIGNED FOR RAW SEWAGE APPLICATIONS. 45 3/18
Series 4XSHD 32 Frame Driver www.cranepumps.com Specifications: Series: 4XSHD 75-100HP, 1750RPM, 60Hz Explosion Proof, Class I, Division 1, Groups C & D, T4 C Canadian Standards Association File No. LR16567 US Sample Specifi cations: Section Page H. DESCRIPTION: SUBMERSIBLE NON-CLOG SEWAGE PUMP DESIGNED FOR RAW SEWAGE APPLICATIONS. DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accommodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE... Cast Iron ASTM A-48, Class 30 WEAR RING... C954 Lead-Free Bronze MOTOR HOUSING... Cast Iron ASTM A-48, Class 30 SEAL PLATE... Cast Iron ASTM A-48, Class 30 IMPELLER: Design... Enclosed Dual Vane, With Pump Out Vanes on Back Side. Dynamically Balanced ISO G6.3 Material... Ductile Iron ASTM A-536, 65-45-12 SHAFT... 416 Stainless Steel O RINGS... Buna-N HARDWARE... 300 Series Stainless Steel LIFTING BAIL... 300 Series Stainless Steel PAINT SEAL:... Axalta Corlar Epoxy, Two Coats Design... Tandem Mechanical, Oil Filled Reservoir. Material: Inboard... Rotating Faces - Carbon Stationary Faces - Ceramic Material: Outboard... Rotating Faces - Silicon Carbide Stationary Faces - Silicon Carbide Elastomer - Buna-N Hardware - 300 Series Stainless CORD ENTRY... 50 ft. (12.1m) Cord. Rigid quick change epoxy-potted housing POWER CORD... CSA Certifi ed Submersible Power Cable 2000V - Ordered Separately SPEED... 1750 RPM UPPER BEARING: Design... Single Row, Ball, Oil Lubricated Load... Radial LOWER BEARING: Design... Double Row, Ball, Oil Lubricated Load... Radial & Thrust MOTOR: Design... NEMA B Three Phase Torque Curve. Oil-Filled, Squirrel Cage Induction, Inverter Duty rated per NEMA MG1 Insulation... Class H Varnish & Magnet Wire THREE PHASE... Requires overload protection to be included in control panel. MOISTURE SENSOR... Normally Open (N/O), Requires Relay in Control Panel TEMPERATURE SENSOR... Three Normally Closed (N/C). To be wired in series with control circuit. OPTIONAL EQUIPMENT... Seal Material, Impeller Trims, Cord Length, Leg Kit MARKINGS... CSA WEIGHT... 1553 lbs (705 Kg) SUBMERGENCE... Max Depth 66ft (20m) RECOMMENDED: Accessories... Break Away Fitting (BAF) Check Valve Control Panel 46 3/18
www.cranepumps.com Series 4XSHDF 18 Frame Driver inches (mm) Optional Leg Kit - p/n 125506 IMPORTANT! 1.) MOISTURE AND TEMPERATURE SENSORS MUST BE CONNECTED TO VALI THE CSA LISTING. 2.) A SPECIAL MOISTURE SENSOR RELAY IS REQUIRED IN THE CONTROL PANEL FOR PROPER OPERATION OF THE MOISTURE SENSORS. CONTACT BARNES PUMPS FOR INFORMATION CONCERNING MOISTURE SENSING RELAYS FOR CUSTOMER SUPPLIED CONTROL PANELS. 3.) THESE PUMPS ARE CSA LISTED FOR PUMPING WATER AND WASTEWATER. DO NOT USE TO PUMP FLAMMABLE LIQUIDS. NOT SUITABLE FOR ENVIRONMENTS CONTAINING GASOLINE OR HEXANE. 4.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE. 47 3/18
Series 4XSHDG www.cranepumps.com 18 Frame Driver inches (mm) 21 Frame Driver Optional Leg Kit - p/n 125506 IMPORTANT! 1.) MOISTURE AND TEMPERATURE SENSORS MUST BE CONNECTED TO VALI THE CSA LISTING. 2.) A SPECIAL MOISTURE SENSOR RELAY IS REQUIRED IN THE CONTROL PANEL FOR PROPER OPERATION OF THE MOISTURE SENSORS. CONTACT BARNES PUMPS FOR INFORMATION CONCERNING MOISTURE SENSING RELAYS FOR CUSTOMER SUPPLIED CONTROL PANELS. 3.) THESE PUMPS ARE CSA LISTED FOR PUMPING WATER AND WASTEWATER. DO NOT USE TO PUMP FLAMMABLE LIQUIDS. NOT SUITABLE FOR ENVIRONMENTS CONTAINING GASOLINE OR HEXANE. 4.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE. 48 3/18
www.cranepumps.com Series 4XSHDI 21 Frame Driver inches (mm) 28 Frame Driver Optional Leg Kit - p/n 125506B IMPORTANT! 1.) MOISTURE AND TEMPERATURE SENSORS MUST BE CONNECTED TO VALI THE CSA LISTING. 2.) A SPECIAL MOISTURE SENSOR RELAY IS REQUIRED IN THE CONTROL PANEL FOR PROPER OPERATION OF THE MOISTURE SENSORS. CONTACT BARNES PUMPS FOR INFORMATION CONCERNING MOISTURE SENSING RELAYS FOR CUSTOMER SUPPLIED CONTROL PANELS. 3.) THESE PUMPS ARE CSA LISTED FOR PUMPING WATER AND WASTEWATER. DO NOT USE TO PUMP FLAMMABLE LIQUIDS. NOT SUITABLE FOR ENVIRONMENTS CONTAINING GASOLINE OR HEXANE. 4.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE. 49 3/18
Series 4XSHDI www.cranepumps.com 32 Frame Driver inches (mm) Optional Leg Kit - p/n 125506B IMPORTANT! 1.) MOISTURE AND TEMPERATURE SENSORS MUST BE CONNECTED TO VALI THE CSA LISTING. 2.) A SPECIAL MOISTURE SENSOR RELAY IS REQUIRED IN THE CONTROL PANEL FOR PROPER OPERATION OF THE MOISTURE SENSORS. CONTACT BARNES PUMPS FOR INFORMATION CONCERNING MOISTURE SENSING RELAYS FOR CUSTOMER SUPPLIED CONTROL PANELS. 3.) THESE PUMPS ARE CSA LISTED FOR PUMPING WATER AND WASTEWATER. DO NOT USE TO PUMP FLAMMABLE LIQUIDS. NOT SUITABLE FOR ENVIRONMENTS CONTAINING GASOLINE OR HEXANE. 4.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE. 50 3/18
www.cranepumps.com Series 4XSHD MODEL NO PART NO 4XSHDF3074 133808 3.0 4XSHDF30N4 133809 3.0 HP VOLT PH Hz RPM (Nom) NEMA START CODE FULL LOAD SERVICE FACTOR SERVICE FACTOR LOCKED ROTOR DRIVER FRAME CORD P/N CORD SIZE D 14.9 1.2 18.5 59.1 1 60 1750 18 125496 12/4-18/4 230 F 14.1 1.2 16.5 66.3 9.7 1.2 11.4 125496 12/4-18/4 58.2 / 65.8 230 3 60 1750 K 9.2 1.2 10.6 18 125496 12/4-18/4 460 4.6 1.2 5.3 32.9 125497 12/4-18/4 4XSHDF3054 133810 3.0 575 3 60 1750 N 4.5 1.2 4.9 37.0 18 125497 12/4-18/4 4XSHDF5074 133811 5.0 4XSHDF50N4 133812 5.0 D 27.2 1.2 35.6 1 60 1750 99.9 / 112.4 18 125498 8/4-18/4 230 F 25.4 1.2 30.2 15.8 1.2 18.7 125496 12/4-18/4 82.4 / 92.4 230 3 60 1750 J 15.0 1.2 17.2 18 125496 12/4-18/4 460 7.5 1.2 8.6 46.2 125497 12/4-18/4 4XSHDF5054 133813 5.0 575 3 60 1750 J 6.0 1.2 6.9 37.0 18 125497 12/4-18/4 XSHDF Pump 4XSHDF75N4 133815 7.5 23.8 1.2 28.5 105.9 / 125496 12/4-18/4 230 3 60 1750 H 23.7 1.2 27.2 123.6 18 125496 12/4-18/4 460 11.9 1.2 13.6 61.8 125497 12/4-18/4 4XSHDF7554 133816 7.5 575 3 60 1750 H 9.5 1.2 10.9 49.4 18 125497 12/4-18/4 4XSHDF100N4 133817 10.0 32.2 1.2 41.4 105.9 / 125498 8/4-18/4 230 3 60 1750 E 29.8 1.2 35.6 123.6 18 125498 8/4-18/4 460 14.9 1.2 17.8 61.8 125497 12/4-18/4 4XSHDF10054 133818 10.0 575 3 60 1750 E 11.9 1.2 14.2 49.4 18 125497 12/4-18/4 IMPORTANT! Moisture and Temperature sensor leads are integral to power cord. Pump rated for operation at ± 10% voltage at motor. Cord Suffi x: XC - 30 Feet, XF - 50 Feet, XJ - 75 Feet, or XL - 100 Feet. Cord sold separately. 51 5/12
Series 4XSHD www.cranepumps.com MODEL NO 4XSHDG5074 133271 5.0 4XSHDG50N4 133272 5.0 PART NO HP VOLT PH Hz RPM (Nom) NEMA START CODE FULL LOAD SERVICE FACTOR SERVICE FACTOR LOCKED ROTOR DRIVER FRAME CORD P/N CORD SIZE D 27.2 1.2 35.6 99.9 1 60 1750 18 125498 8/4-18/4 230 F 25.4 1.2 30.2 112.4 15.8 1.2 18.7 125496 12/4-18/4 82.4 / 92.4 230 3 60 1750 J 15.0 1.2 17.2 18 125496 12/4-18/4 460 7.5 1.2 8.6 46.2 125497 12/4-18/4 4XSHDG5054 133273 5.0 575 3 60 1750 J 6.0 1.2 6.9 37.0 18 125497 12/4-18/4 4XSHDG75N4 133276 7.5 23.8 1.2 28.5 105.9 / 125496 12/4-18/4 230 3 60 1750 H 23.7 1.2 27.2 123.6 18 125496 12/4-18/4 460 11.9 1.2 13.6 61.8 125497 12/4-18/4 4XSHDG7554 133277 7.5 575 3 60 1750 H 9.5 1.2 10.9 49.4 18 125497 12/4-18/4 4XSHDG100N4 133278 10.0 32.2 1.2 41.4 105.9 / 125498 8/4-18/4 230 3 60 1750 E 29.8 1.2 35.6 123.6 18 125498 8/4-18/4 460 14.9 1.2 17.8 61.8 125497 12/4-18/4 4XSHDG10054 133279 10.0 575 3 60 1750 E 11.9 1.2 14.2 49.4 18 125497 12/4-18/4 4XSHDG150N4 132608 15.0 51.8 1.2 59.0 230 3 60 1750 E 46.9 1.2 54.3 206.6 21 125498 8/4-18/4 XSHDG Pump 460 23.4 1.2 27.2 103.3 125497 12/4-18/4 4XSHDG15054 132609 15.0 575 3 60 1750 E 18.7 1.2 21.7 82.6 21 125497 12/4-18/4 230 53.7 1.2 59.0 125498 8/4-18/4 4XSHDG20084 132610 20.0 3 60 1750 J 383.9 21 460 26.9 1.2 29.9 125497 12/4-18/4 4XSHDG20054 132611 20.0 575 3 60 1750 J 21.5 1.2 23.9 153.5 21 125497 12/4-18/4 4XSHDG75N6 136351 7.5 24.9 1.2 29.6 230 3 60 1150 J 24.0 1.2 27.6 137.6 21 125496 12/4-18/4 460 12.0 1.2 13.8 68.8 125497 4XSHDG7556 136352 7.5 575 3 60 1150 J 9.6 1.2 11.0 55.0 21 125497 12/4-18/4 IMPORTANT! Moisture and Temperature sensor leads are integral to power cord. Pump rated for operation at ± 10% voltage at motor. Cord Suffi x: XC - 30 Feet, XF - 50 Feet, XJ - 75 Feet, or XL - 100 Feet. Cord sold separately. 52 12/13
www.cranepumps.com Series 4XSHD MODEL NO PART NO 4XSHDI150N4 140059XP* 15.0 HP VOLT PH Hz RPM (Nom) NEMA START CODE FULL LOAD SERVICE FACTOR SERVICE FACTOR 51.8 59.0 1.2 230 3 60 1750 E 46.9 54.3 LOCKED ROTOR 206.6 DRIVER FRAME 21 CORD P/N CORD SIZE 125498 8/4-18/4 460 23.4 1.2 27.2 103.3 125497 12/4-18/4 4XSHDI15054 140061XP* 15.0 575 3 60 1750 E 18.7 1.2 21.7 82.6 21 125497 12/4-18/4 4XSHDI20064 131013 20.0 3 60 1750 G 63.0 1.2 74.6 323.0 28 138318 6/4-18/4 4XSHDI20084 131014 20.0 230 53.7 1.2 59.0 125498 8/4-18/4 3 60 1750 J 383.9 21 460 26.9 1.2 29.9 125497 12/4-18/4 4XSHDI20054 131015 20.0 575 3 60 1750 J 21.5 1.2 23.9 153.5 21 125497 12/4-18/4 4XSHDI25094 130629 25.0 77.8 1.2 93.4 3 60 1750 G 230 71.4 1.2 82.3 359.0 28 138319 2/4-18/4 4XSHDI25044 130630 25.0 460 3 60 1750 G 33.2 1.2 38.9 191.9 21 125499 8/4-18/4 4XSHDI25054 130631 25.0 575 3 60 1750 G 26.6 1.2 31.1 153.5 21 125497 12/4-18/4 4XSHDI30094 130632 30.0 93.4 1.2 116.9 3 60 1750 E 230 82.3 1.2 98.7 359.0 28 138319 2/4-18/4 4XSHDI30044 130633 30.0 460 3 60 1750 F 38.9 1.2 45.9 191.9 21 125499 8/4-18/4 4XSHDI30054 130634 30.0 575 3 60 1750 F 31.1 1.2 36.7 153.5 21 125499 8/4-18/4 4XSHDI40034 130635 40.0 230 3 60 1750 E 106.0 1.2 126.4 486.0 28 138319 2/4-18/4 4XSHDI40044 130636 40.0 460 3 60 1750 E 53.0 1.2 63.2 243.0 28 138318 6/4-18/4 4XSHDI40054 130637 40.0 575 3 60 1750 E 42.4 1.2 50.6 194.4 28 138317 8/4-18/4 4XSHDI50044 130638 50.0 460 3 60 1750 F 67.1 1.2 79.0 339.0 28 138318 6/4-18/4 4XSHDI50054 130639 50.0 575 3 60 1750 F 53.7 1.2 63.2 271.2 28 138318 6/4-18/4 4XSHDI60044 130640 60.0 460 3 60 1750 E 79.0 1.2 95.5 339.0 28 138319 2/4-18/4 4XSHDI60054 130641 60.0 575 3 60 1750 E 63.2 1.2 76.4 271.2 28 138318 6/4-18/4 4XSHDI75044 139487XP 75.0 460 3 60 1750 G 108.4 1.15 120.7 578.0 32 138319 2/4-18/4 4XSHDI75054 139488XP 75.0 575 3 60 1750 G 86.7 1.15 96.6 462.4 32 138319 2/4-18/4 4XSHDI100044 139489XP 100.0 460 3 60 1750 E 136.6 1.15 155.3 578.0 32 138319 2/4-18/4 4XSHDI100054 139490XP 100.0 575 3 60 1750 E 109.2 1.15 124.2 462.4 32 138319 2/4-18/4 XSHDI Pump IMPORTANT! Moisture and Temperature sensor leads are integral to power cord. Pump rated for operation at ± 10% voltage at motor. Cord Suffi x: XC - 30 Feet, XF - 50 Feet, XJ - 75 Feet, or XL - 100 Feet. Cord sold separately. * Select impeller diameter when ordering. 53 3/16
Series 4XSHD www.cranepumps.com MODEL NO PART NO 4XSHDI75N6 141218* 7.5 HP VOLT PH Hz RPM (Nom) NEMA START CODE FULL LOAD SERVICE FACTOR SERVICE FACTOR 24.9 1.2 29.6 230 3 60 1150 J 24.0 1.2 27.6 LOCKED ROTOR 137.6 DRIVER FRAME 21 CORD P/N 125496 CORD SIZE 12/4-18/4 460 12.0 1.2 13.8 68.8 125497 4XSHDI7556 141214* 7.5 575 3 60 1150 J 9.6 1.2 11.0 55.0 21 125497 12/4-18/4 4XSHDI100N6 141219 10.0 32.9 1.2 41.0 230 3 60 1150 F 30.2 1.2 35.8 137.6 21 125498 8/4-18/4 460 15.1 1.2 17.9 68.8 125497 12/4-18/4 4XSHDI10056 141215 10.0 575 3 60 1150 F 12.1 1.2 14.3 55.0 21 125497 12/4-18/4 4XSHDI150N6 136370 15.0 47.0 1.2 56.8 230 3 60 1150 H 44.1 1.2 51.4 248.6 21 125498 8/4-18/4 460 22.0 1.2 25.7 124.3 125497 12/4-18/4 4XSHDI15056 136371 15.0 575 3 60 1150 H 17.6 1.2 20.6 99.4 21 125497 12/4-18/4 4XSHDI20096 136372 20.0 60.3 1.2 71.5 3 60 1150 H 230 57.2 1.2 69.8 354.0 28 138318 6/4-18/4 4XSHDI20046 136373 20.0 460 3 60 1150 E 28.6 1.2 34.9 124.3 21 125499 8/4-18/4 4XSHDI20056 136374 20.0 575 3 60 1150 E 22.9 1.2 27.9 99.4 21 125497 12/4-18/4 XSHDI Pump 4XSHDI25096 136375 25.0 75.2 1.2 90.8 3 60 1150 G 230 70.5 1.2 82.6 354.0 28 138319 2/4-18/4 4XSHDI25046 136376 25.0 460 3 60 1150 G 35.4 1.2 41.3 177.0 28 138317 8/4-18/4 4XSHDI25056 136377 25.0 575 3 60 1150 G 28.3 1.2 33.0 141.6 28 138317 8/4-18/4 4XSHDI30096 136378 30.0 90.8 1.2 114.9 3 60 1150 E 230 82.6 1.2 99.7 354.0 28 138319 2/4-18/4 4XSHDI30046 136379 30.0 460 3 60 1150 E 41.3 1.2 49.9 177.0 28 138317 8/4-18/4 4XSHDI30056 136380 30.0 575 3 60 1150 E 33.0 1.2 39.9 141.6 28 138317 8/4-18/4 4XSHDI40036 136381 40.0 230 3 60 1150 E 110.4 1.2 131.8 476.0 28 138319 2/4-18/4 4XSHDI40046 136382 40.0 460 3 60 1150 E 55.2 1.2 65.9 238.0 28 138318 6/4-18/4 4XSHDI40056 136383 40.0 575 3 60 1150 E 44.2 1.2 52.7 190.4 28 138317 8/4-18/4 IMPORTANT! Moisture and Temperature sensor leads are integral to power cord. Pump rated for operation at ± 10% voltage at motor. Cord Suffi x: XC - 30 Feet, XF - 50 Feet, XJ - 75 Feet, or XL - 100 Feet. Cord sold separately. * Select impeller diameter when ordering. 54 3/17
www.cranepumps.com Series 4XSHD Performance Curve 3-10HP, 1750RPM, 60Hz TOTAL METERS HEAD FEET 4XSHDF Pump STANDARD IMPELLER SIZES 24 21 80 70 Pump HP Impeller Dia. mm (in) 10.0 190 (7.48) 7.5 180 (7.09) 5.0 160 (6.30) 3.0 140 (5.51) 18 60 190mm 20% Service Factor: 1.20 30% 15 50 40% 50% 180mm 170mm 60% 12 40 160mm 65% 9 30 150mm 140mm 60% 6 20 130mm 50% 40% 3 10 U.S. GALLONS PER MINUTE LITERS PER SECOND 200 12 30% 10 HP 7.5 HP 3 HP 5 HP 4SHDF 1750RPM 18 FRAME 400 600 800 1000 1200 24 36 48 60 72 84 55 6/12
Series 4XSHD Performance Curve 5-10HP, 1750RPM, 60Hz, 18 Frame www.cranepumps.com TOTAL METERS HEAD FEET 4XSHDG Pump STANDARD IMPELLER SIZES 24 21 80 70 20% 30% 40% 220mm 50% 60% Pump HP Impeller Dia. mm (in) 10.0 200 (7.87) 7.5 185 (7.28) 5.0 170 (6.69) 18 60 200mm Service Factor: 1.20 15 50 185mm 68% 12 40 180mm 170mm 60% 9 30 165mm 50% 40% 6 20 3 10 U.S. GALLONS PER MINUTE LITERS PER SECOND 200 12 10 HP 5 HP 7.5 HP 12 HP 4SHDG 1750RPM 18 FRAME 400 600 800 1000 1200 24 36 48 60 72 84 56 6/12
www.cranepumps.com Series 4XSHD Performance Curve 15-20HP, 1750RPM, 60Hz, 21 Frame TOTAL METERS HEAD FEET 4XSHDG Pump STANDARD IMPELLER SIZES 31.5 105 235mm 35% Pump HP Impeller Dia. mm (in) 20.0 235 (9.25) 15.0 210 (8.25) 27.0 90 220mm 45% 55% 65% Service Factor: 1.20 210mm 22.5 75 71% 200mm 18.0 60 190mm 13.5 45 20 HP 165mm 9.0 30 15 HP 4.5 15 4SHDG 1750RPM U.S. GALLONS PER MINUTE 200 400 600 800 1000 1200 LITERS PER SECOND 12 24 36 48 60 72 84 57 6/12
Series 4XSHD Performance Curve 7.5HP, 1150RPM, 60Hz www.cranepumps.com 4XSHDG Pump 58 12/13
www.cranepumps.com Series 4XSHDI Performance Curve 15-100HP, 1750RPM, 60Hz 275 250 225 370 mm 350 mm 25 35 45 55 STANDARD IMPELLER SIZES Pump HP Impeller Dia. mm (in.) 100 75 60 50 40 30 25 20 15 370 (14.57) 330 (12.99) 315 (12.40) 295 (11.61) 280 (11.02) 260 (10.24) 245 (9.65) 235 (9.25) * 200 330 mm 65 * Select impeller diameter when ordering 68 315 mm 65 175 100 hp 295 mm 150 Head - ft 280 mm 55 125 260 mm 100 245 mm 235 mm 75 hp 230 mm 75 25 35 45 55 45 60 hp 50 65 65 50 hp 35 55 40 hp 25 45 35 15 hp 30 hp 25 hp 20 hp 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 US gpm 59 2/16
Series 4XSHD Performance Curve 15-40HP, 1150RPM, 60Hz www.cranepumps.com 4XSHDI Pump 60 2/17