Visit for our online catalog or to use the Internet Hydraulic Selection Guide.

PRODUCT CATALOG

Index What s New Hydraulic Driven Centrifugal Pumps - MAX Series Hydraulic Driven Centrifugal Pumps -7 PTO Driven Centrifugal Pumps -9 Belt Driven Centrifugal Pumps (Counterclockwise) - Belt Driven Centrifugal Pumps (Clockwise) - Electric Motor Driven Centrifugal Pumps Gasoline Engine Driven Centrifugal Pumps 7-9 ACE/VALVTEC Ball Valves Application Information General Information Pipe & Hose Friction Tables Pump Selection Worksheet Visit www.acepumps.com for our online catalog or to use the Internet Hydraulic Selection Guide.

WHAT S NEW FMC-7-HYD See page for more information FMC-SS-HYD- See page for more information FMCWS-F-HYD See page for more information FMC-SS-MAG-DX See page for more information Poly Impeller For Series CCW pumps including HYD and PTOC models Polypropylene is a great alternative to more expensive options when applying ammonia. Extend the usefulness of your Series pump in ammonia applications by using the new poly impeller. Stainless Impeller For Series CCW and Max Series pumps Optional stainless steel impellers now available for ultimate corrosion resistance.

HYDRAULIC DRIVEN CENTRIFUGAL PUMPS General Advantages Ace developed the first hydraulic motor driven pump at the request of John Deere in 99. Ace continues to develop a comprehensive range of reference materials and hydraulic accessories allowing the pumps to be effectively applied on the full range of hydraulic systems. Centrifugal pump design provides good resistance to abrasive solutions and extra flow for agitation. All hydraulic driven pumps are equipped with a stainless steel shaft and wear ring for excellent corrosion resistance. The advantages of the hydraulic motor driven pump are: MOUNTING VERSATILITY: The location of the pump is not tied to the PTO or engine drive shaft; the pump can be mounted in a variety of locations to suit application requirements. CUSTOMIZED PERFORMANCE: The performance is dependent on the supply of hydraulic oil to the motor and not necessarily tied to engine speed. A hydraulic driven pump can produce higher pressures than PTO or belt driven pumps. They can also hold constant pressure at varying engine speeds on closed center hydraulic systems. EASY MAINTENANCE: On a hydraulic driven pump there are no belts to align or break. Separate pump and hydraulic motor shafts simplify repair and replacement. Two main pump bearings support shaft loads. All pumps are equipped with easily replaceable Viton mechanical seals. The Ace gear type hydraulic motor is more efficient than gerotor type motors, and is less subject to damage by contamination than the gerotor design. A built-in needle valve allows for the bypass of up to 9 GPM ( LPM) excess hydraulic fluid on open center systems. The standard motor has a reverse flow check valve which prevents backward hookup and a coasting check which protects the motor seal from the flywheel effect of the impeller. A restrictor orifice is included with pump models recommended for pressure compensating closed center systems. Features Designed for starter fertilizer and small sprayer applications. Replace V diaphragm pumps and roller pumps. Tall Blade Impeller design higher pressure at standard engine speeds. All Polypropylene corrosion resistant construction. The R motor requires GPM (. LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Open Center Systems up to GPM (9. LPM) using internal needle valve The R motor requires 7 GPM (. LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (. LPM) using internal needle valve FMC-7-HYD- FMC-7-HYD- " / " Maximum Flow: 7 GPM ( LPM) Maximum Pressure: PSI (.9 BAR) OIL FLOW GPM.... LPM.... Roundup is a registered trademark of Monsanto Company. Viton is a registered trademark of Dupont Dow Elastomers. Note: Graph for FMC-7-HYD- model.

Features The farm industry standard since 99. The and motors require GPM (7. LPM) and GPM (. LPM) hydraulic fluid input. Recommended for engineered systems with limited oil flow. The motor requires GPM (. LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Open Center Systems up to GPM (9. LPM) using internal needle valve bypass The motor requires GPM (7.9 LPM) maximum hydraulic fluid input. Load Sensing Closed Center Systems Open Center Systems up to 7 GPM (. LPM) using internal needle valve bypass The motor requires GPM (. LPM) maximum hydraulic fluid input. Large Open Center Systems up to GPM (9.9 LPM) using internal needle valve bypass FMC-HYD- FMC-HYD- FMC-HYD- / " " FMC-HYD- FMC-HYD- FMC-HYD- Maximum Flow: 9 GPM ( LPM) Maximum Pressure: PSI (.9 BAR). GPM OIL. GPM OIL. GPM OIL FMC--HYD- / " Note: Graph for FMC-HYD- model. / " 7 OIL FLOW GPM... LPM..9. Features Provides higher pressure and greater volume for applications with large tanks and longer spray booms. The motor requires 7 GPM (. LPM) maximum hydraulic fluid input and fits virtually all tractor hydraulic systems. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (. LPM) using internal needle valve bypass Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) 7. GPM OIL. GPM OIL. GPM OIL OIL FLOW GPM... LPM...

HYDRAULIC DRIVEN CENTRIFUGAL PUMPS FMC-F-HYD- FMC-FS-HYD- FMC-F-HYD- / " FLANGE / " FLANGE Features F model equipped with NPT ports and industry standard flanged connections. FS model constructed of stainless steel with NPT ports and industry standard flanged connections. SP model is self-priming making it perfect for load and spray applications. Provides higher pressure and greater volume for applications with large tanks and longer spray booms. The motor requires 7 GPM (. LPM) maximum hydraulic fluid input and fits virtually all tractor hydraulic systems. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (. LPM) using internal needle valve bypass The motor requires GPM (. LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (7.7 LPM) using internal needle valve bypass Maximum Flow: GPM (9 LPM) GPM (7 LPM) for Maximum Pressure: PSI (. BAR) PSI (9 BAR) for Note: Graph for FMC-F-HYD- model. FMC-SP-HYD- / ". GPM OIL. GPM OIL GPM OIL / " Maximum Flow: GPM (9 LPM) Maximum Pressure: PSI (. BAR) 7. GPM OIL. GPM OIL. GPM OIL 7 7 OIL FLOW GPM.. OIL FLOW GPM 7... LPM..9.9 LPM.9..

FMC--HYD- FMC--HYD- FMC-SS-HYD- FMC--HYD- " / " Features: SS model has stainless steel wet end including impeller, volute, and seal plate. F model equipped with industry standard flanged connections. Ideal for spraying, large tank agitation, liquid transfer, and spray - transfer combinations The motor requires GPM (7.9 LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to 7 GPM (. LPM) using internal needle valve bypass The motor requires GPM (. LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Maximum Flow: GPM (77 LPM) Maximum Pressure: PSI (. BAR), PSI (. BAR) for 7 FMC-F-HYD- FLANGE GPM OIL GPM OIL 9 GPM OIL Note: Graph for FMC--HYD- model. FLANGE 7 OIL FLOW GPM LPM. 7.9 9. Load Sensing Closed Center Systems Open Center Systems up to GPM (7.7 LPM) using internal needle valve bypass The motor requires GPM (. LPM) maximum hydraulic fluid input. Large Open Center Systems up to GPM (9.9 LPM) using internal needle valve bypass Maximum Flow: GPM (9 LPM) Maximum Pressure: PSI (. BAR) 7 GPM OIL. GPM OIL GPM OIL OIL FLOW GPM. LPM.. 7.9

General Advantages Ace s MAX Series pumps are designed from the ground up for today s demanding applications. Each model is engineered for maximum reliability and performance. A durable e-coat finish provides extra corrosion resistance on all surfaces inside and out. The psi high efficiency pressure plated gear motors provide higher output with less oil flow. The impellers are designed to develop higher pressure at lower shaft speeds. A splined motor to pump shaft connection strengthens the power train while allowing for easy repair and maintenance. Oversized bearings round out the list of features for long, trouble free life. Features Modified impeller design develops higher pressure at lower RPM. F model equipped with NPT ports and industry standard flanged connections. The M motor requires GPM ( LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM ( LPM) WS model equipped with Oasis Wetseal Technology MAX SERIES HYDRAULIC DRIVEN CENTRIFUGAL PUMPS FMC--HYD / " / " Maximum Flow: GPM ( LPM) Maximum Pressure: PSI ( BAR) FMC-F-HYD FMCWS-F-HYD / " FLANGE / " FLANGE Maximum Flow: 7 GPM (. LPM) Maximum Pressure: PSI ( BAR) 7 OIL FLOW GPM.... 9. GPM.... 9.. LPM.. 7.... OIL FLOW LPM.9..9. 7..

OasisWetSeal.com The WS- MAX, 7 MAX and MAX pump models feature our Oasis WetSeal Technology. The dual shaft seals run in a pressurized barrier fluid which is specially formulated for seal face lubrication and heat dissipation. The liquid being pumped never comes into contact with the seal surfaces so abrasive wear failures are prevented. Additionally, the buffer fluid lubricates and cools the seal faces even when run dry to eliminate costly failure. FMC-7F-HYD-M FMC-7F-HYD-M FLANGE FLANGE Features & Pressure balanced impeller eliminates thrust load on bearings. Standard industry flanged ports for higher flow. Hydraulic motor case drain option for extended seal life on engineered systems. Separate motor and pump shafts for easy maintenance. The M motor requires GPM (. LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (. LPM) The M motor requires GPM (7.7 LPM) maximum hydraulic fluid input. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (7.7 LPM) The M motor requires GPM (7 LPM) maximum hydraulic fluid input with # SAE case drain port and is standard on the MAX pump. Pressure Compensating Closed Center Systems Load Sensing Closed Center Systems Open Center Systems up to GPM (7 LPM) Maximum Flow: 9 GPM (97 LPM) Maximum Pressure: PSI (. BAR) FMC-F-HYD FLANGE FLANGE Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) Note: Graph for FMC-7F-HYD-M model. OIL FLOW GPM 7..9... OIL FLOW GPM.... LPM..9. 9.9. LPM 7. 77. 9..7 9.9 7

PTO DRIVEN CENTRIFUGAL PUMPS General Advantages PTO belt driven centrifugal pumps were first introduced by Ace in 9 and enabled the applicator to mount centrifugal pumps directly on RPM and RPM tractor PTO shafts. The simple, yet durable design of the PTOC pump has withstood the test of time while many attempts at imitation have come and gone. The key to success of the Ace belt driven pump has been the Spring Loaded Idler. The idler maintains proper belt tension which minimizes the load on the pump bearings. More importantly, the idler helps absorb the shock of PTO engagement that can destroy cog belts or gears. Model PTOC belt driven pumps are easy to operate and maintain. Belts can be replaced in the field with minimum downtime and at little cost. Maintenance features also include sealed ball bearings and a readily replaceable mechanical seal. The belt guard provides complete coverage of the pulleys, shaft and belt. All PTO driven pumps are equipped with a stainless steel shaft and wear ring for excellent corrosion resistance. SPRING LOADED IDLER PTO Tumble Rod Mounting L = L H = H On trailer mounted units the hitch pin must be centered between the pump and tractor PTO shafts to minimize vibration transferred to the pump when turning. PTOC- PTOC- / " " Features Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) The original belt drive standard since 9 Time tested and field proven design Widespread parts and service availability Most Economical belt drive Roundup is a registered trademark of Monsanto Company. PTOC- PTOC- RPM RPM RPM RPM 7 RPM 9 RPM RPM 7 RPM 7

PTO Shaft Options -SP -SPQC -SP -SP -B /" (.9 MM) spline shaft for RPM models Instant-attach quick coupler for RPM models spline /" (.9 MM) split bore shaft with locking collar for RPM models spline /" (. MM) split bore shaft with locking collar for RPM models " (. MM) stub shaft for installation on trailer sprayers driven by PTO tumblerod PTOC-- PTOC-- / " / " Features Maximum Flow: GPM (7 LPM) Maximum Pressure: PSI (7. BAR) The High Performance Pump. PSI (.9 BAR) at GPM ( LPM) due to increased pulley ratio and larger /" x /" construction Provides higher pressure and greater volume for applications with large tanks and long spray booms Allows fuel savings by operating at lower engine speeds while maintaining adequate spraying pressures PTOC-- PTOC-- RPM RPM RPM RPM 7 RPM 9 RPM RPM 7 RPM 7 9

BELT DRIVEN CENTRIFUGAL PUMPS General Advantages Frame Mount Advantages Ace belt driven pumps are available in a variety of models which can be belt driven or direct coupled to a power source. The pumps are available in either clockwise or counterclockwise rotation. The standard bare shaft pumps are designed with a keyway for mounting a drive pulley or coupling. Magnetic Clutch Driven Advantages The integral magnetic clutch driven centrifugal pump design was first offered by Ace in 9. These models enabled the operator to free the PTO shaft and hydraulic system for other uses. The volt DC magnetic clutch is driven by a v-belt from the engine drive shaft. The clutch is idle until engaged by an on-off toggle switch located at the driver s seat. Typical Clutch Installation Ace magnetic clutch driven frame mounted centrifugal pump models are available with counterclockwise (ccw) rotation and clockwise (cw) rotation. The direction of rotation is determined when facing the shaft. Sizes available are /" x ", /" x /", and " x /". MAGNETIC CLUTCH DRIVEN PUMP OFF-ON SWITCH AMP FUSE TO VOLT SUPPLY ALTERNATOR WATER PUMP SHAFT ENGINE CRANK SHAFT PULLEY FMC-CW--MAG-D -MAG-D CLUTCH ft. lb. (7. NM) torque capacity Forged machined pulley for maximum strength Solid forged rotor to maximize torque E-coated for maximum corrosion protection High temperature epoxy coil Two bearings with high temperature, long life grease Single or double belt drive /" (. CM) pitch diameter FMC-CW--X -X FRAME OPTION /" (.9 CM) diameter stainless steel shaft, standard models /" diameter (.9 CM) Larger bearings for extended life Available with MAG-D clutch /" (. cm) mounting bolt spacing -X frame has " (7. CM) bolt spacing

Pump Rotation The direction of rotation is always determined WHEN FACING THE SHAFT. This rule applies for the pump shaft and the drive shaft. Ace Frame Mounted pumps are available in both clockwise (CW) and counter-clockwise (CCW) rotation. Ace model numbers which include a CW have a clockwise rotation; all other models are counterclockwise rotation. When direct coupling shafts, always MATCH THE OPPOSITE ROTATION pump with the shaft. As illustrated, a gasoline engine with CCW rotation will direct couple to a FMC-CW- pump with clockwise rotation. When mounting a pump with belts and pulleys, either pump rotation can be used to match the drive shaft rotation and the desired direction of the pump. The rotation of several common power sources are as follows: Gasoline engine and electric motor shafts rotate in a counterclockwise direction; a tractor PTO shaft rotates in a clockwise direction; the front tractor engine crankshaft rotates in a counterclockwise direction. CCW ELECTRIC MOTOR: COUNTER CLOCKWISE (CCW) CW FMC-CW- PTO SHAFT: CLOCKWISE (CW) ROTATION Pulley Ratio To get the desired performance from an ACE Frame Mounted Pump, the proper speed ratio between the pump and drive source must be established. The following formula should be helpful: Pump RPM Driveshaft RPM For example: To drive an FMC--MAG pump at RPM with a drive source RPM of and knowing that the clutch pulley diameter on the pump is.7" ( CM), what should the diameter of the drive pulley be? RPM RPM ENGLISH ) x.7 = 7 ) 7 =.9 The drive pulley diameter, when rounded off should be." (7 CM). = = Drive Pulley Diameter Pump Pulley Diameter Drive Pulley Diameter.7" ( CM) METRIC ) x = ) =.7 Belt Alignment and Tension Proper belt alignment and belt tension will prevent premature bearing failure in the clutch and/or the pump. Use a straight edge held on the faces of the pulleys to check alignment. To provide proper belt tension, lay the straight edge on the tops of both pulleys as shown. Use mild force to deflect the belt as shown. Use a ruler to measure the amount of deflection. Proper tension will allow /" ( CM) of deflection for each " ( CM) of distance between the pulleys. For example: If the distance between the pulleys is ' (9 CM), the deflection should be /" ( CM). RULER STRAIGHT EDGE BELT DEFLECTION FMC--MAG PUMP A or B V BELT

BELT DRIVEN CENTRIFUGAL PUMPS COUNTERCLOCKWISE ROTATION FMC FMC-MAG-D / " " Features Counterclockwise Rotation when facing shaft end Stainless Steel Shaft and Wear Ring Chemical resistant Valox or optional Cast Iron Impeller Standard Viton Carbon/Ceramic seal or optional Severe Duty Silicon Carbide Mechanical seal SP model is self-priming making it perfect for load and spray applications. F model equipped with NPT ports and industry standard flanged connections. Maximum Flow: 7 GPM ( LPM) Maximum Pressure: 7 PSI (.7 BAR) Maximum Power:. HP (. KW) RPM RPM RPM RPM FMC- FMC-F FMC-SP FMC--MAG-D / " FMC-F-MAG-D FMC-SP-MAG-D / " Valox is a registered trademark of GE Plastics. Viton is a registered trademark of Dupont Dow Elastomers. Maximum Flow: GPM (9 LPM) Maximum Pressure: PSI (9 BAR) Maximum Power: HP (7. KW) RPM RPM RPM RPM

Features Modified impeller design develops higher pressure at lower RPM. F model equipped with NPT ports and industry standard flanged connections. E-Coat protection for excellent corrosion resistance FMC- FMC-F / " FLANGE FMC--MAG-D FMC-F-MAG-D / " FLANGE Features Counterclockwise Rotation when facing shaft end Stainless Steel Shaft and Wear Ring Chemical resistant Valox or optional Cast Iron Impeller Standard Viton Carbon/Ceramic seal or optional Severe Duty Silicon Carbide Mechanical seal SS model has stainless steel wet end including impeller, volute, and seal plate. Maximum Flow: GPM ( LPM) Maximum Pressure: PSI ( BAR) Maximum Power: HP (. KW) FMC- FMC--MAG-D FMC--MAG-DX FMC-SS-MAG-DX " 7 RPM RPM RPM 7 RPM / " Maximum Flow: GPM (77 LPM) Maximum Pressure: PSI (. BAR) Maximum Power: 7. HP (. KW) 7 RPM RPM RPM RPM 7

BELT DRIVEN CENTRIFUGAL PUMPS CLOCKWISE ROTATION FMC-CW FMC-CW-MAG-D / " " Features Clockwise Rotation when facing shaft end Stainless Steel Shaft and Wear Ring Chemical resistant Valox or optional Cast Iron Impeller Standard Viton Carbon/Ceramic seal or optional Severe Duty Silicon Carbide Mechanical seal MAG-D models equipped with heavy duty V clutch X model has /" (.9 CM) spacing on mounting base. All other models have /" (. CM). DX model for Spra-Coupe Models:,,,,, Maximum Flow: 7 GPM ( LPM) Maximum Pressure: 7 PSI (.7 BAR) Maximum Power:. HP (. KW) FMC-CW- FMC-CW--MAG-D FMC-CW--MAG-DX / " / " RPM RPM RPM RPM Spra-Coupe is a registered trademark of AGCO Corporation. Valox is a registered trademark of GE Plastics. Viton is a registered trademark of Dupont Dow Elastomers. Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) Maximum Power:.7 HP (. KW) RPM RPM RPM RPM 7

Features Clockwise Rotation when facing shaft end Modified impeller design develops higher pressure at lower RPM. E-Coat protection for excellent corrosion resistance Standard Viton Carbon/Ceramic seal or optional Severe Duty Silicon Carbide Mechanical seal MAG-D models equipped with heavy duty V clutch FMC-CW- FMC-CW--MAG-D Maximum Flow: GPM ( LPM) Maximum Pressure: PSI ( BAR) Maximum Power: HP (. KW) / " FLANGE / " FLANGE 7 RPM RPM RPM 7 RPM Features Clockwise Rotation when facing shaft end Stainless Steel Shaft and Wear Ring Chemical resistant Valox or optional Cast Iron Impeller Standard Viton Carbon/Ceramic seal or optional Severe Duty Silicon Carbide Mechanical seal MAG-D models equipped with heavy duty V clutch FMC-CW- FMC-CW--MAG-D " / " Maximum Flow: GPM (77 LPM) Maximum Pressure: PSI (. BAR) Maximum Power: 7. HP (. KW) RPM RPM RPM RPM.......

BELT DRIVEN CENTRIFUGAL PUMPS CLOCKWISE ROTATION Features Large diameter impeller provides higher pressure at slower speeds Easily replaceable mechanical seal Clockwise Rotation when facing shaft end Stainless Steel Shaft All iron construction Heavy duty double row ball bearings Standard Viton Carbon/Ceramic seal or optional Severe Duty Silicon Graphite Mechanical seal FMC-CW- FMC-CW--MAG-D " / " Maximum Flow: GPM ( LPM) Maximum Pressure: 7 PSI (.7 BAR) Maximum Power:. HP (. KW) 7 Features For most industrial and agricultural blending, mixing, seed treating and liquid transfer applications. Easy replaceable Viton mechanical seal Non-overloading / HP (. KW) RPM single phase totally enclosed fan cooled electric motor, for use in all dusty, dirty or weather exposed locations. Optional silicon carbide seal available for abrasive solutions. Chemical resistant Valox or optional Cast Iron Impeller ELECTRIC MOTOR DRIVEN CENTRIFUGAL PUMP Valox is a registered trademark of GE Plastics. Viton is a registered trademark of Dupont Dow Elastomers. ACH- / " RPM RPM RPM RPM " Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) ENGLISH UNITS METRIC UNITS PRESSURE FLOW FLOW PRESSURE FLOW PSI GPM GPH BAR LPM. 7..7 7.7.. 9.. Data based on foot lift through unrestricted suction hose and fittings with full /" I.D. FLOW LPH 7 9 A complete line of electric motor driven pumps is available. Contact the factory for details.

GASOLINE ENGINE DRIVEN CENTRIFUGAL PUMPS General Advantages Ace offers a complete line of Gasoline Engine Driven Centrifugal Pumps. The pumps provide service where power sources are limited or unavailable. The pumps are ideally suited to develop pressure for spray or transfer applications. The pumps feature a direct coupled design with an easily replaceable mechanical seal and slinger ring between the pump and engine to prevent liquid from damaging the engine. The pumps are available complete or less engine (-LE). Complete units come assembled on the specified engine ready to install and run. Less engine (-LE) units come with all hardware necessary to mount on the specified engine. Features Tall Blade Impeller design higher pressure at standard engine speeds GE-7 Impeller attaches directly to /" (.9 CM) keyed shaft engine GE- Impeller attaches directly to /" (.9 CM) keyed shaft engine All Polypropylene corrosion resistant construction Available complete or less engine GE-7 GE- " / " GE-7 Maximum Flow: GPM (9 LPM) Maximum Pressure: 7 PSI (. BAR) 7 9 RPM RPM RPM Note: Graph for GE-7 model with Honda GX- engine. GE- Maximum Flow: GPM (9 LPM) Maximum Pressure: PSI (. BAR) 7 RPM RPM RPM Note: Graph for GE- model with Honda GX- engine...... 7

GASOLINE ENGINE DRIVEN CENTRIFUGAL PUMPS GE--A Features Impeller attaches directly to /" (.9 CM) NF threaded shaft on HP (. KW) to. HP (. KW) engine Stainless steel shaft sleeve with o-ring leak protection All iron construction Available complete or less engine GE--A / " " Maximum Flow: GPM (9 LPM) Maximum Pressure: PSI (. BAR) RPM RPM RPM.... GE- Features Impeller attaches directly to /" (.9 CM) NF threaded shaft on. HP (. KW) engine Stainless steel shaft sleeve with o-ring leak protection All iron construction Available complete or less engine GE- GE- / " / " GE- Features Impeller attaches directly to /" (.9 CM) keyed shaft on. HP (. KW) engine Optional electric start engine All iron construction Available complete or less engine Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) RPM RPM RPM 7

GE- Features Impeller attaches directly to " (. CM) - NF threaded shaft on HP (.9 KW) to HP (7. KW) engine Stainless steel shaft sleeve with double o-ring leak protection All iron construction Available complete or less engine GE- GE- " / " GE- Features Impeller attaches directly to " (. CM) keyed shaft on HP (.9 KW) to HP (7. KW) engine Optional electric start engine All iron construction Available complete or less engine Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (9.7 BAR) RPM RPM RPM GE- Features Impeller attaches directly to " (. CM) - NF threaded shaft on HP ( KW) to HP ( KW) engine Standard HP ( KW) electric start engine Stainless steel shaft sleeve with double o-ring leak protection All iron construction Available complete or less engine GE- / " " Maximum Flow: GPM ( LPM) Maximum Pressure: PSI (. BAR) RPM RPM RPM 9

ACE/VALVTEC BALL VALVES General Advantages ACE/VALVTEC ball valves are the premium valves for critical uses. The valves are available with ratchet or quarter turn handle designs. ACE/VALVTEC puts the durability of metal where performance counts. SERIES STANDARD PORT Available with /-turn handle or ratchet handle. An open-closed indicator is provided with ratchet handle model. Operation of ratchet handle may be cable, chain, cord, or push-pull rods. Available in cast iron, aluminum, or bronze. Choice of hard chrome plated carbon steel balls or stainless balls. Size range /" to " NPT. Standard Valve Features Unique diagonally split valve body for easy cleaning and service Ratchet on/off or quarter turn operation Rugged all-metal bodies in cast iron, aluminum, or bronze Hard chrome plated or stainless steel balls Standard and full port models Withstand working pressures up to PSI (7. BAR) SERIES FULL PORT A full flow valve available with /-turn or ratchet handle. Available in cast iron only. Size range /" to " NPT. RATCHET HANDLES Ratchet handles are available for Series and Series valves and can be supplied for right or left handed operation and either with flow or crossflow. An open-closed indicator is provided with ratchet handle model. Operation of ratchet handle may be cable, chain, cord, or push-pull rods. Please specify when ordering.. L.H. with flow. R.H. with flow. L.H. cross flow. R.H. cross flow

APPLICATION INFORMATION SPRAYER PLUMBING SUGGESTIONS The primary goal when plumbing a sprayer pump is to route liquid from the pump to the spray boom with minimum restriction. Minimizing restrictions is necessary for achieving the pump s maximum rated capacity. ) Hoses should be the same size as the pump s suction and discharge ports. ) Install a pressure gauge and valve on the discharge side of the pump for the purpose of measuring the SHUT-OFF pressure. ) A minimum number of elbows, fittings, and valves should be used to reduce pressure losses. ) Plumb a straight section of hose leading into the suction port equal to times the hose inside diameter. (i.e. / " hose = " of straight hose) ) Avoid locating electronic spray control valves between the pump and boom. Following these guidelines is necessary for delivering the highest pressures to the boom. USEFUL FORMULAS GPA = 9 x GPM (per Nozzle) MPH x W GPM (per Nozzle) = GPA x MPH x W 9 GPA = Gallons Per Acre GPM = Gallons Per Minute MPH = Miles Per Hour W Pressure Spike Valve Suggested for MAX Series = Nozzle spacing (in inches) for broadcast spraying = Spray width (in inches) for single nozzles, band spraying, or boomless spraying = Row spacing (in inches) divided by the number of nozzles per row for directed spraying. Jet Agitator Boom Valves Anti-Vortex Tank Fitting Agitation Pressure Gauge Agitation Valve Control Valve Tank Valve Flowmeter Shut-off Valve Pressure Gauge Line Strainer A A = x hose diameter PUMP MOUNTING The following are basic guidelines for proper pump mounting: ) The pump should be mounted below the tanks to allow gravity to naturally fill the pump with liquid. ) The volute should be oriented with the discharge port pointing up or across the top of the pump which allows air to rise out of the pump. ) A petcock valve may be installed in the top most pipe plug hole to allow air to be bled off each time the tanks are filled. ) Another option would be to install a /'' air bleed line from the top most pipe plug hole to the sprayer tank. This will continually bleed air from the pump housing. ) If the pump must be located above the liquid level, a check valve should be installed to maintain the pump s prime. ACE centrifugal pumps are straight centrifugals and must be primed prior to operation. The word primed means the pump must be completely full of water and any trapped air vented before operation. Following the pump mounting guidelines will insure proper priming of the pump and avoid premature seal failure.

GENERAL INFORMATION USEFUL FACTORS OR FORMULAS WHP = BHP = EFF = Ft. Head x GPM 9 WHP or BHP = EFF WHP x BHP WHP = Water Horsepower BHP = Brake Horsepower EFF = Pump Efficiency To determine the approximate horsepower required for an ACE centrifugal pump at a given flow and pressure: HP = GPM x PSI 7 x. To determine the speed at which a liquid is traveling: Velocity (ft/sec) =. x GPM (pipe diameter) To determine the heat generated from by-passed hydraulic oil: BTU Per Hour = GPM x PSI x., BTU/HR = Ton Refrigeration Feet Head = Ft. Head x GPM 9 x EFF (Pump) PSI (water) x. specific gravity PSI (pounds per square inch) = Feet Head x. Weight of one U.S. Gallon of water =. pounds One cubic foot (cu. ft.) of water contains 7. gallons Specific gravity of water (sp. gr.) =. SPECIFIC GRAVITY Water weighs. lbs./gallon and has a specific gravity of. Since specific gravity is a ratio of the weight of a liquid compared to the weight of water, the specific gravity of a liquid such as % nitrogen fertilizer, which weighs. lbs./gallon would be figured thus:. lbs./gallon =. specific gravity. lbs./gallon SOLUTION WEIGHT. lbs./gal.. lbs./gal. 9. lbs./gal.. lbs./gal.. lbs./gal.. lbs./gal. All pump capacities (GPM) in this catalog are based on water. When pumping fluids that are heavier than water, pump capacity will be less than stated on each pump performance table. To compensate for pumping heavy liquids, multiply the required pump capacity in GPM times the appropriate conversion factor from the above chart. EXAMPLE: Required pump capacity is GPM of % nitrogen fertilizer. x. =. GPM Then select a pump from the preceding pages that will deliver. GPM at the desired pressure. CONVERSION FACTORS SPECIFIC GRAVITY.9..... CONVERSION FACTOR.9..... Multiply By To Obtain LENGTH inches. millimeters (mm) inches. centimeters (cm) feet. meters (m) miles.9 kilometers (km) AREA acres.7 square meters (m ) acres.7 hectares (ha) hectares.7 acres VOLUME gallons.7 cubic decimeters (dm ) gallons.7 liters (L) gallons cubic inches (in ) Imperial gallons. liters (L) Imperial gallons. U.S. gallons U.S. gallons. Imperial gallons liter. gallon pounds water.9 gallon FLOW RATE gallons/hour (gph).7 liters/hour (L/h) gallons/minute (gpm).7 liters/minute (L/m) APPL. RATE gallons/acre (gpa) 9. liters/hectare (L/ha) PRESSURE pounds per square inch (psi).9 kilopascals (kpa) PSI. ft. (head) of water ft. (head) of water. PSI inches mercury (in Hg).9 PSI bar. PSI kilopascal (KPA). PSI SPEED miles/hour (mph).9 kilometers/hour (km/h) kilometers/hour (km/h). miles/hour (mph)

PIPE & HOSE FRICTION TABLES FLOW PRESSURE DROP IN PSI FOR VARIOUS PIPE SIZES (FT. LENGTH) IN GPM /" /" /" /" /" " / " / "...................7.9.9.............7...............7.....9.......9.........................9...7.....9.7..79......7 NOTE: The above figures are for standard pipe of either seamless or welded construction, in good clean condition. Recommended maximum capacity to keep velocity at approximately ft. per second is shown above heavy lines. PRESSURE DROP IN PSI FOR VARIOUS HOSE SIZES ft. length with no coupling FLOW /" /" /" /" /" " / " / " IN GPM I.D. I.D. I.D. I.D. I.D. I.D. I.D. I.D.............. 9......................7...... 9..7.....7.............9........ 9..9 7... NOTE: The above figures are for standard hose in good condition with no couplings. APPROXIMATE FRICTION LOSS IN PIPE FITTINGS in terms of equivalent feet of straight pipe. STD. STD. PIPE ACTUAL GATE GLOBE ELBOW TEE SIZE INSIDE VALVE VALVE OR RUN THRU STD. DIAM. RUN OF OF TEE SIDE WT. IN. FULL FULL ELBOW STD. REDUCED OUTLET OPEN OPEN TEE / /.9....7. /...... /....7..7. /....97....9. 9..... -/..7.... 7. -/....9.7...7..... -/.9. 9.9...

PUMP SELECTION WORKSHEET Visit our web site at www.acepumps.com to use an automated version of this worksheet.. Fill in the application information:. Complete the calculations Application Rate (GPA) Speed (MPH) Nozzle Spacing (inches) x x = 9 = x = GPM per Nozzle # of Nozzles Boom Flow (GPM). Identify the flow required for AGITATION (typically % of tank s capacity): GPM Gallon Tank 7 GPM 7 Gallon Tank GPM Gallon Tank 7 GPM Gallon Tank. Then Add: Boom Flow (GPM) + Agitation (GPM) = Total Pump Flow (GPM) required + =. Determine your highest spraying pressure (PSI). (Add - PSI for system pressure losses.). Find the TOTAL PUMP FLOW (GPM) calculated above.. Choose the pump by color code or catalog performance charts. PUMP SELECTION PUMP PRESSURE (PSI) 7 9 FMC-HYD Series FMC--HYD Series HYDRAULIC PUMPS TOTAL PUMP FLOW (GPM) 7 9 7 9 7 9 FMC--HYD Series FMC--HYD Series FMC-7F-HYD Series FMC-F-HYD Series PUMP PRESSURE (PSI) 7 9 PTO PUMPS TOTAL PUMP FLOW (GPM) 7 9 PTOC Series PTOC- Series

YEARS OF INNOVATION AND STILL PUMPING FARM INDUSTRY STANDARD We look for inspiration everywhere. For years, we ve developed the best in pump technology while providing the service and support to match. Pumps are our sole focus. We strive to produce the highest performing components for today s sprayers. Thank you for trusting us. To learn about our entire line of high-performance pumps, visit www.acepumps.com or call --9. Years of Innovation and Sti ll Pumpin ping

ACE PUMP CORPORATION P.O. Box 7 Channel Ave. Memphis, TN phone:..9 fax: 9.77.7 www.acepumps.com ACE Form# PROD CATALOG