INSTLLTION INSTRUTIONS FOR PRT 99-05 PPLITIONS hevrolet orvette 990-996 99-05 KIT FETURES ISO mount Radio Provision with Pocket Two ISO Mount Unit s Provision Double DIN Radio Provision KIT OMPONENTS ( ) Pocket ( ) rackets ( ) Trim Plate ( D) (4) #6 X /4 Phillips Head Screws (E) () #8 X /8 Phillips Head Screws D WIRING ND NTENN ONNETIONS (Sold Separately) Wiring Harness: 70-856 - 7ft bypass harness (Non-ose) 989-996 70-857 - 7ft bypass harness (ose) 989-996 ntenna dapter: Not required TOOLS REQUIRED: Phillips Screwdriver Rotary utting Tool E
99-05 DSH DISSSEMLY 990-996 HEVROLET ORVETTE Disconnect the negative battery terminal to prevent an accidental short circuit. Remove () screws from center vent and remove vent. (Figure ) Remove rubber inserts in cup holders and remove screw. (Figure ) 4 Remove () screws from under carpet inside center console. 5 6 7 8 Set parking brake and place shifter into the drive position. Lift the center console up and slide back. (Figure ) Remove () screws from radio/climate control trim panel and remove panel. (Figure ) Remove () screws from side trim panels to gain access to radio screws and remove (4) screws securing radio, unplug and remove radio.
99-05 DSH DISSSEMLY 990-996 HEVROLET ORVETTE 9 ut and remove obstruction from rear of radio cavity. (Figure D) D UT OUT
99-05 KIT SSEMLY 990-996 HEVROLET ORVETTE ISO MOUNT RDIO WITH POKET Mount the pocket trim-plate to the pocket using the () #8x/8 Phillips head screws provided with kit. Larger lip towards top of pocket. (Figure ) lign the mounting holes in the brackets with the mounting holes in the side of the radio and mount the brackets to the radio using screws provided with the radio. (Figure ) lign the mounting holes in the brackets below the radio with the mounting holes in the pocket and mount the pocket to the brackets using the (4) #6x/4 Phillips head screws provided with the kit. (Figure ) 4 ontinue to final assembly.
99-05 KIT SSEMLY 990-996 HEVROLET ORVETTE DOULE DIN RDIO PROVISION lign the mounting holes in the left bracket with the mounting holes in the left side of the radio and mount the bracket to the radio using screws provided with the radio. (Figure ) Repeat step one with the right bracket on the right side of the radio. ontinue to final assembly. TWO ISO MOUNT UNITS lign the mounting holes in the left bracket with the mounting holes in the left side of both units and mount the bracket to both units using screws provided with the units. (Figure ) Repeat step one with the right bracket on the right side of the units. ontinue to final assembly.
FINL SSEMLY Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. 99-05 FINL SSEMLY ) Strip wire ends back /" ) Twist ends together ) Solder D) Tape D METR / EI WIRING ODE V Ignition / cc... Red V att / Memory.. Yellow Ground........... lack* Power ntenna..... lue mp Turn-On...... lue / White mp Ground....... lack / White Illumination........ Orange Dimmer.......... Orange / White Right Front (+)..... Gray Right Front (-)...... Gray / lack Left Front (+)...... White Left Front (-)....... White / lack Right Rear (+)...... Violet Right Rear (-)...... Violet / lack Left Rear (+)....... Green Left Rear (-)....... Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. METR ESSORIES STEREO DSH KITS