1. (a) set of decorative lights consists of a string of lamps. Each lamp is rated at 5.0 V, 0.40 W and is connected in series to a 230 V supply. Calculate the number of lamps in the set, so that each lamp operates at the correct rating, the current in the circuit, (iii) the resistance of each lamp, (iv) the total electrical energy transferred by the set of lights in 2 hours. When assembled at the factory, one set of lights inadvertently contains 10 lamps too many. ll are connected in series. ssume that the resistance of each lamp is the same as that calculated in part (a) (iii). Calculate the current in this set of lights when connected to a 230 V supply. How would the brightness of each lamp in this set compare with the brightness of each lamp in the correct set? 2. battery of EMF and internal resistance r is connected in series to a variable resistor and an ammeter of negligible resistance. voltmeter is connected across, as shown in the figure on the right. (a) State what is meant by the EMF of the battery. The reading on the voltmeter is less than the EMF. Explain why this is so. student wishes to measure and r. Using the circuit shown in the figure above the value of is decreased in steps and at each step the readings V and I on the voltmeter and ammeter respectively are recorded. These are shown in the table. reading on voltmeter/v reading on ammeter/ 8.3 0.07 6.8 0.17 4.6 0.33 2.9 0.44 0.3 0.63 Give an expression relating V, I, and r. Draw a graph of V (on the y-axis) against I (on the x-axis) on graph paper. (Graph paper should be provided) (iii) Determine the values of and r from the graph, explaining your method. (8) (Total 12 marks) page 1 (LJ 2010)
3. Four resistors, each having resistance of, are connected to form a square. resistance meter measured the resistance between different corners of the square. Determine the resistance the meter records when connected between the following corners. (a) etween and C, as in Figure 1 etween and, as in Figure 2 Figure 1 Figure 2 C C D D (Total 5 marks) 4. (a) In the circuit shown on the right, the battery has an EMF of 6.0 V. With the switch closed and the lamp lit, the reading on the voltmeter is 5.4 V. Explain without calculation, why the voltmeter reading is less than the EMF of the battery. torch is powered by two identical cells each having an EMF of 1.5 V and an internal resistance r. The cells are connected in series. The torch bulb is rated at 1.6 W and the voltage across it is 2.5 V. Draw the circuit described. Calculate the internal resistance of each cell. (c) In the circuit on the left the cell has emf and internal resistance r. The voltage V across the cell is read on the voltmeter which has infinite resistance, and the current I through the variable resistor is read on the ammeter. y altering the value of the variable resistor, a set of values of V and I is V obtained. These values, when plotted, give the graph shown on the right. Show how the values of and r may be obtained from this graph. Explain your method. (Total 11 marks) 0 I page 2 (LJ 2010)
5. (a) steady current of 0.25 passes through a torch bulb for 6 minutes. Calculate the charge which flows through the bulb in this time. The torch bulb is now connected to a battery of negligible internal resistance. The battery supplies a steady current of 0.25 for 20 hours. In this time the energy transferred in the bulb is 9.0 10 4 J. Calculate the potential difference across the bulb, the power of the bulb. 6. In the circuit shown in the figure below, the battery, of negligible internal resistance, is connected to two resistors which form a potential divider. (Total 5 marks) 160 X 110 (a) Calculate the current through the ammeter. Y 20 Ω resistor is now connected between X and Y. State and explain, without further calculation, whether the current through the ammeter will increase or decrease. You may be awarded marks for the quality of written communication in your answer. The 20 Ω resistor is now removed and replaced with a voltmeter. Stating the assumption made, show that the reading on the voltmeter is 4.9 V. (c) The voltmeter is now removed and the terminals X and Y joined together with a wire. Calculate the reading on the ammeter. 7. (a) On the right there are two possible arrangements of connecting three resistors, each resistor having a resistance of 40. Calculate the equivalent resistance in each case. page 3 (LJ 2010)
The designer of a heating element for the rear window of a car decides to connect six separate heating elements together as shown below. Each element has a resistance of 6.0 and the unit is connected to a dc supply having zero internal resistance. Calculate the current in each single element. With the aid of a similar calculation give a reason why the heater would not be as effective if all six were connected in series. 8. In the circuit shown below, the battery, of EMF 6.0V, has negligible internal resistance. 20 6.0 V S 60 (a) Calculate the current through the ammeter when the switch S is open, closed. The switch S is now replaced with a voltmeter of infinite resistance. Determine the reading on the voltmeter. (Total 5 marks) 9. (a) student is given three resistors of resistance 3.0 Ω, 4.0 Ω and 6.0 Ω respectively. Draw the arrangement, using all three resistors, which will give the largest resistance. Calculate the resistance of the arrangement you have drawn. (iii) Draw the arrangement, using all three resistors, which will give the smallest resistance. (iv) Calculate the resistance of the arrangement you have drawn. The three resistors are now connected to a battery of emf and negligible internal resistance, as shown on the right Calculate the total resistance in the circuit. Calculate the voltage across the 6.0 Ω resistor. (Total 9 marks) 3.0 6.0 4.0 page 4 (LJ 2010)
10. (a) X and Y are two lamps. X is rated at, 24 W and Y at 6.0 V, 18 W. Calculate the current through each lamp when it operates at its rated voltage. The two lamps are connected in the circuit shown. The battery has an EMF of 27 V and negligible internal resistance. The resistors 1 and 2 are chosen so that the lamps are operating at their rated voltage. 1 Y 27 V 2 X V high resistance voltmeter What is the reading on the voltmeter? Calculate the resistance of 2. (iii) Calculate the current through 1. (iv) Calculate the voltage across 1. (v) Calculate the resistance of 1. 11. (a) In the circuit shown on the right, the battery, of EMF 15 V and the negligible internal resistance, is connected in series with two lamps and a resistor. The three components each have a resistance of 12. (7) (Total 9 marks) 15 V 12 What is the voltage across each lamp? Calculate the current through the lamps. 12 12 15 V 12 The two lamps are now disconnected and reconnected in parallel. Show that the current supplied by the battery is 0.83. Hence show that the current in each lamp is the same as the current in the lamps in the circuit in part a. 12 12 (c) How does the brightness of the lamps in the series circuit compare with the brightness of the lamps in the parallel circuit? Explain your answer. page 5 (LJ 2010)
12. battery of e.m.f and negligible internal resistance is connected to a resistor network as shown in the circuit diagram. (a) Calculate the total resistance of the circuit. Calculate the current through the resistor. (1) (Total 4 marks) 13. (a) In the circuit shown on the right, the battery has an EMF of and negligible internal resistance. 40 20 40 I P PQ is a potential divider, S being the position of the sliding contact. In the position shown, the resistance between P and S is 180 and the resistance between S and Q is 60. Calculate the current, I, in the circuit, assuming that there is no current through the voltmeter V. What property of the voltmeter allows us to assume that no current flows through it? (iii) What is the reading on the voltmeter? Q S V The circuitfrom part a is modified as shown on the right, by exchanging the voltmeter for a load, whose resistance is about the same as the resistance of section SQ of the potential divider. I P Explain, without calculation, why the current through the battery increases in value from that in part (a). (Total 6 marks) Q S 14. battery of EMF 24 V and negligible internal resistance is connected to a resistor network as shown in the circuit diagram in the diagram on the right. 30 40 (a) Show that the resistance of the single equivalent resistor that could replace the four resistors between the points and is. If 1 is, calculate 60 the current in 1, the current in the 60 resistor. 1 120 24 V page 6 (LJ 2010)
15. Two resistors, and, have different resistances but otherwise have identical physical properties. E is a cell of negligible internal resistance. E E figure 1 figure 2 When the resistors are connected in the circuit shown in figure 1, reaches a higher temperature than. When connected in the circuit shown in figure 2, reaches a higher temperature than. Explain these observations fully, stating which resistance is greater. (Total 6 marks) 16. In the circuit shown on the right, the battery has negligible internal resistance. I (a) If the emf of the battery = 9.0 V, 1 = 120 and 2 = 60, calculate the current I flowing in the circuit. 9.0 V 1 Calculate the voltage reading on the voltmeter. 2 V The circuit shown in the diagram acts as a potential divider. The circuit is now modified by replacing 1 with a temperature sensor, whose resistance decreases as the temperature increases. Explain whether the reading on the voltmeter increases or decreases as the temperature increases from a low value. (Total 7 marks) 17. In the circuit shown, the battery has negligible internal resistance. Calculate the current in the ammeter when (a) the terminals X and Y are shortcircuited i.e. connected together, 30 the terminals X and Y are 6.0 V X connected to a 30 resistor. 60 (Total 6 marks) Y page 7 (LJ 2010)
18. heating element, as used on the rear window of a car, consists of three strips of a resistive material, joined, as shown in the diagram, by strips of copper of negligible resistance. The voltage applied to the unit is and heat is generated at a rate of 40 W. + 0 V copper (a) Calculate the total resistance of the element. resistive material Hence show that the resistance of a single strip is about 11. If each strip is 2.6 mm wide and 1.1 mm thick, determine the length of each strip. (resistivity of the resistive material = 4.0 10 5 m) page 8 (LJ 2010)