SEE VICTAULIC PUBLICATIO.01 FOR DETAILS Style 99 Roust-A-Bout couplings are designed with heavy housings and grips to provide a strong component for joining plain and beveled end, including Schedule steel pipe and Victaulic plain end fittings. Roust-A-Bout couplings are not designed for use on plastic pipe, pipe with brittle linings, cast or ductile iron pipe nor any pipe with a surface hardness greater than 10 Brinell. Pipe is secured together by heavy jaws, which are set into the housing. All sizes are supplied with painted housings and plated nuts and bolts. Galvanized housings are available. WARIG Style 99 Roust-A-Bout couplings must be assembled with nuts tightened to full torque specifications. 1 ½ 12'' SIZES 14 18'' SIZES bv Rotterdamseweg 2m 2629HH Delft Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 Exaggerated for clarity Exaggerated for clarity 1 ½ 18'' SIZES 1''; 76.1 & 139.7 MM SIZES MATERIAL SPECIFICATIOS Housing: Ductile iron conforming to ASTM A-36, grade 6-4-12. Ductile iron conforming to ASTM A-39, grade 6-4-1, is available upon special request. Housing Coating: Orange enamel. Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 Optional: Hot dipped galvanized and others. Jaws: Carbon steel, case hardened, electroplated, except sizes 1''; 76.1 and 139.7, which utilize stainless steel, Type 416, hardened. Gasket: (specify choice*) Grade E EPDM EPDM (Green color code). Temperature range 30 F to +230 F/ 34 C to +1 C. Recoended for cold and hot water service within the specified temperature range plus a variety of dilute acids, oil-free air and many chemical services. UL classified in accordance with ASI/SF 61 for cold +86 F/+30 C and hot +1 F/+82 C potable water service. OT RECOMMEDED FOR PETROLEUM SERVICES. Grade T nitrile itrile (Orange color code). Temperature range 20 F to +1 F/ 29 C to +82 C. Recoended for petroleum products, air with oil vapors, vegetable and mineral oils within the specified temperature range. ot recoended for hot water services over +10 F/+66 C or for hot dry air over +1 F/+60 C. * Services listed are General Service Recoendations only. It should be noted that there are services for which these gaskets are not recoended. Reference should always be made to the latest Victaulic Gasket Selection Guide for specific gasket service recoendations and for a listing of services which are not recoended. s/uts/washers: Heat-treated plated carbon steel, trackhead meeting the physical and chemical requirements of ASTM A-449 and physical requirements of ASTM A-183. The 6"/10 and larger sizes are supplied with hardened steel washers meeting ASTM F-436 Type 3 (weathering steel). JOB/OWER COTRACTOR EGIEER System o. Submitted By Spec Sect Para Location Date Approved Date 1
DIMESIOS Y X 1 6"/2 10 MM SIZES Y X 8 12"/200 300 MM SIZES Y X 14 18"/30 40 MM SIZES bv Rotterdamseweg 2m 2629HH Delft Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 Z Z Z Max Work Press. End Load * Required /ut o. Dimensions / Lb. Ft. ** m X Y Z Aprx. Weight 1 1.31 600 0 3 2.6 4.2 2.2 1.7 2 3 8 x 2 2 33.7 4130 360 47. 6 8 7 0.8 1 ½ 1.900 70 20 60 3.2.0 2.88 3.6 2 ½ x 2 ½ 48.3 17 934 81.4 83 1 73 1.6 2 2.37 70 3300 10 3.7 6.7 3.38.3 2 8 x 3 ¼ 0 60.3 17 1468 203.4 9 171 86 2.4 2 ½ 2.87 600 3890 10 4.2 7.13 3.38.7 2 8 x 3 ¼ 6 73.0 4130 173 203.4 8 181 86 2. 76.1 3.000 0 282 9 4.69 6.2 2.7 4.4 2 ½ x 2 ¾ 76.1 2700 1200 128.8 119 19 70 2.0 3 3.00 600 770 200.00 8.0 3.38 8.7 2 ¾ x 4 ¼ 88.9 4130 2676 271.2 127 216 86 3.9 3 ½ 4.000 00 62 200.0 9.2 3.63.6 2 ¾ x 4 ¼ 90 1.6 340 27946 271.2 1 23 92 4.8 4 4.00 40 71 200 6.13.00 4.00 12.8 2 ¾ x 4 ¼ 0 114.3 30 318 271.2 16 24 2.8 139.7.00 20 9 160 7..7 3.19 9.0 2 ¾ x 139.7 1700 264 217.0 200 260 81 4.1.63 30 0 20 7.2 11.38 4.38 17.3 2 7 8 x 12 141.3 20 3782 339.0 184 289 111 7.8 6 6.62 300 3 20 8.0 13.38 4.38 23.2 2 1 x 6 # 10 168.3 206 46013 339.0 216 3 111. 16.1 6.00 300 99 20 8.38 13.2 4.38 22.2 2 1 x 6 # 16.1 206 44300 339.0 213 337 111.1 8 8.62 20 14600 20.88 14.38.00 37.2 4 7 8 x # 200 219.1 1700 64970 339.0 276 36 127 16.9.70 20 22700 300 13.38 16.38.00 48.2 4 7 8 x # 20 273.0 1700 1 6.8 3 416 127 21.9 12 12.70 20 31900 30 1.0 19.63.13 60.0 4 1 x 6 ½ # 300 323.9 1700 1419 474.6 394 499 130 27.2 14 14.000 200 300 30 16.7 20.7.38 89.0 8 1 x 6 ½ # 30 3.6 10 137060 474.6 42 27 137.4 16 16.000 10 30200 30 19.00 22.63.38.0 8 1 x 6 ½ # 0 6.4 00 134390 474.6 483 7 137 47.6 18 18.000 10 38200 30 21.00 23.0.38 12.0 8 1 x 6 ½ # 40 47.0 00 169990 474.6 33 97 137 6.7 * and are total, from all internal and external loads, based on coupling properly assembled, with bolts fully torqued to listed specifications, on plain end or beveled end standard weight (ASI) steel pipe and Victaulic plain end fittings. Couplings are designed to be used with plain end pipe and Victaulic plain end fittings only. ** torque ratings shown must be applied at installation. Metric thread size bolts (plated) are available (color coded) for all coupling sizes upon request. Contact Victaulic for details. WARIG: Depressurize and drain the piping system before attempting to install, remove, or adjust any Victaulic piping products. # Supplied with flat washers. kg _2
PRESSURE RATIGS AD ED LOADS Carbon Steel Pipe 1 2 1 2 3 4 6 Pipe Req d 1.31 33.7 1 ½ 1.900 48.3 2 0 2.37 60.3 2 ½ 2.87 6 73.0 3 3.00 88.9 Table continued on page 4. 0.179 4. m 0.133 600 0 3.38 3 4130 360 0.9 47. 600 0 2.77 4130 360 0.06 0 0 1.6 270 240 0.200 70 20.08 17 934 0.14 70 20 3.68 60 17 934 0.9 81.4 600 1700 2.77 4130 76 0.06 0 10 1.6 270 489 0.218 70 3300.4 17 1468 0.14 70 3300 3.91 10 17 1468 0.9 203.4 0 10 2.77 270 0.06 200 900 1.6 137 0 0.276 600 3890 7.01 4130 173 0.203 600 3890.16 10 4130 173 203.4 300 1900 3.0 206 84 10 00 3 440 0.300 600 770 7.62 4130 267 0.216 600 770.49 200 4130 267 271.2 22 2160 3.0 10 96 12 1200 860 3 Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _3
PRESSURE RATIGS AD ED LOADS Carbon Steel Pipe 1 2 3 4 6 3 ½ 4.000 90 1.6 4 0 12 6 10 16.1 8 200 4.00 114.3.63 141.3 6.62 168.3 6.00 16.1 8.62 219.1 Table continued on page. Pipe Req d m 0.318 00 62 8.08 340 2794 0.226 00 62.74 200 340 2794 271.2 200 200 3.0 137 1112 0 120 690 6 0.337 40 71 8.6 30 318 0.237 40 71 6.02 200 30 318 271.2 17 20 3.0 1200 12460 60 90 41 4230 0.37 30 0 9.3 24 3782 0.28 30 0 6. 20 24 3782 339.0 10 3600 3. 3 16020 0.9 7 10 2.77 1 0.432 300 3.97 206 4601 0.2 300 3 7.11 20 206 4601 339.0 0 300 3. 690 17 0.9 7 2600 2.77 1 1170 0.20 300 99 6.3 206 44300 0.200 20 17 6000.08 339.0 1200 26700 0.10 0 300 3.81 690 17 0.322 20 14600 8.18 172 64970 0.277 200 11700 30 7.04 20 137 206 0.148 339.0 0 6000 3.76 690 26700 0.9 0 3000 2.77 34 1330 Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _4
PRESSURE RATIGS AD ED LOADS Carbon Steel Pipe 20 12 300 1 2 3 4 6.70 273.0 12.70 323.9 Pipe Req d m 0.36 20 22700 9.27 172 1 0.307 17 1900 30 7. 300 1200 707 0.16 6.8 7 60 4.19 1 30260 0 400 3. 34 2002 0.37 20 31900 STD 9.3 172 1419 0.330 10 190 30 8.38 30 3 8499 0.1 474.6 0 12700 4.7 690 61 0.16 7 900 4.19 1 4227 14 14.000 0.37 30 200 300 STD 30 3.6 9.3 474.6 137 137060 16 16.000 0.37 30 10 30200 STD 0 6.4 9.3 474.6 3 134390 COLUM 1: Victaulic couplings are identified by nominal pipe size. COLUM 2: pipe wall thickness. COLUM 3: Pipe wall thickness schedule as established in ASI Standard B36, -70. COLUM 4: torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column and Permissible Maximum s listed in Column 6. TORQUE RATIGS MUST BE APPLIED AT ISTALLATIO. COLUM : Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. pressure ratings are based on pipe prepared in accordance with Victaulic specifications. COLUM 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications. OTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼''/6.4. This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement. ROUST-A-BOUT COUPLIGS ARE DESIGED FOR USE WITH PLAI ED OR BEVELED ED PIPE AD VICTAULIC PLAI ED FITTIGS OLY. Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _
PRESSURE RATIGS AD ED LOADS Stainless Steel Pipe 1 33.4 1 ½ 48.3 2 60.3 2 ½ 73.0 3 88.9 3 ½ 1.6 4 114.3 141.3 1 2 3 4 6 Pipe Req d 1.31 33.7 1.900 48.3 2.37 60.3 2.87 73.0 3.00 88.9 4.000 1.6 4.00 114.3.63 141.3 Table continued on page 7. m 0.133 3 600 0 3.38 47. 4130 360 0.9 3 0 0 2.77 47. 270 240 0.06 3 20 30 1.6 47. 172 1 0.14 60 00 1.0 3.6 81.4 340 6230 0.9 60 0 1.0 2.77 81.4 270 489 0.06 1.6 /R /R /R 0.14 10 00 2.200 3.91 203.4 340 9790 0.9 10 0 1.0 2.77 203.4 270 0.06 1.6 /R /R /R 0.203 10 0 2.00.16 203.4 270 1112 10 20 1.00.16 203.4 172 667 /R /R /R 0.216 200 0 3.0.49 271.2 270 169 200 200 1.900 3.0 271.2 137 84 /R /R /R 0.226 200 300 3.700.74 271.2 206 1646 200 10 1.900 3.0 271.2 3 84 /R /R /R 0.237 200 20 3.900 6.02 271.2 172 173 200 1.300 3.0 271.2 0 78 /R /R /R 0.28 20 200 4.0 6. 339.0 137 21360 20 7 1.0 3. 339.0 0.9 2.77 /R /R /R Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _6
PRESSURE RATIGS AD ED LOADS Stainless Steel Pipe 6 168.3 16.1 8 219.1 273.0 12 323.9 1 2 3 4 6 Pipe Req d 6.62 168.3 6.00 16.1 8.62 219.1.70 273.0 12.70 323.9 m 0.2 20 200 6.0 7.11 339.0 137 30260 20 7 2.600 3. 339.0 1 1170 0.9 2.77 /R /R /R 0.2 20 200 6.0 7.11 339.0 137 30260 20 7 2.600 3. 339.0 1 1170 0.9 2.77 /R /R /R 0.322 20 200 11.000 8.18 339.0 137 4890 0.148 20 7 4.0 3.76 339.0 1 19 0.9 20 2 1.460 2.77 339.0 170 649 0.36 300 0 9.000 9.27 6.8 690 00 0.16 300 0 4.00 4.19 6.8 34 2002 300 2 2.20 3. 6.8 170 0 0.6 30 0 12.70.31 474.6 690 673 0.1 30 0 6.0 4.67 474.6 34 284 0.16 30 2 3.200 3.96 474.6 170 142 R = ot recoended + Contact Victaulic for details. COLUM 1: Victaulic couplings are identified by nominal pipe size. COLUM 2: pipe wall thickness. COLUM 3: Pipe wall thickness schedule as established in ASI Standard B36, -70. COLUM 4: torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column and Permissible Maximum s listed in Column 6. TORQUE RATIGS MUST BE APPLIED AT ISTALLATIO. COLUM : Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. pressure ratings are based on pipe prepared in accordance with Victaulic specifications. COLUM 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications. OTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼''/6.4 ). This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement. ROUST-A-BOUT COUPLIGS ARE DESIGED FOR USE WITH PLAI ED OR BEVELED ED PIPE AD VICTAULIC PLAI ED FITTIGS OLY. Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _7
PRESSURE RATIGS AD ED LOADS Aluminum Pipe* 1 2 1 2 3 4 6 1.31 33.7 1 ½ 1.900 48.3 2 0 2.37 60.3 2 ½ 2.87 6 73.0 3 3.00 88.9 Table continued on page 9. 0.179 4. Pipe Req d m /R /R /R 0.133 3 600 0 3.38 47. 4130 360 0.9 3 300 0 2.77 47. 206 17 0.06 3 0 13 1.6 47. 690 601 0.200 60 00 10.08 81.4 340 6230 0.14 60 0 10 3.6 81.4 2760 489 0.9 60 300 82 2.77 81.4 206 3671 0.06 1.6 /R /R /R 0.218 10 0 10.4 203.4 2760 0.14 10 300 1300 3.91 203.4 206 78 0.9 10 200 900 2.77 203.4 13 0 0.06 1.6 /R /R /R 0.276 10 30 2200 7.01 203.4 241 9790 0.203 10 27 172.16 203.4 189 7676 10 10 00.16 203.4 3 440 /R /R /R 0.300 200 300 28 7.62 271.2 206 12816 0.216 200 200 1920.49 271.2 13 844 200 0 960 3.0 271.2 690 4272 /R /R /R Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _8
PRESSURE RATIGS AD ED LOADS Aluminum Pipe* 1 2 3 4 6 3 ½ 4.000 90 1.6 4 0 12 6 10 8 200 4.00 114.3.63 141.3 6.62 168.3 8.62 219.1 Table continued on page. Pipe Req d m 0.318 200 20 30 8.08 271.2 172 1379 0.226 200 200 200.74 271.2 13 1112 200 0 120 3.0 271.2 690 63 /R /R /R 0.337 200 200 3200 8.6 271.2 13 142 0.237 200 10 20 6.02 271.2 3 6 200 0 0 3.0 271.2 34 360 /R /R /R 0.37 20 10 3600 9.3 339.0 3 16020 0.28 20 0 20 6. 339.0 690 6 20 0 1200 3. 339.0 34 3 0.9 2.77 /R /R /R 0.432 20 10 200.97 339.0 3 231 0.2 20 0 300 7.11 339.0 690 17 20 0 170 3. 339.0 34 7788 0.9 20 3 122 2.77 339.0 2 41 0.322 20 10 9000 8.18 339.0 3 00 0.277 20 0 6000 30 7.04 339.0 690 26700 0.20 20 7 400 20 6.3 339.0 1 2002 0.148 20 0 3000 3.76 339.0 34 1330 Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _9
PRESSURE RATIGS AD ED LOADS Aluminum Pipe* 20 12 300 1 2 3 4 6.70 273.0 12.70 323.9 Pipe Req d m 0.36 300 0 9000 9.27 6.8 690 00 0.307 300 7 6300 30 7. 6.8 1 23 0.20 300 0 400 20 6.3 6.8 34 2002 0.16 300 2 220 4.19 6.8 172 013 0.6 300 0 120.31 6.8 690 6960 0.330 300 7 900 30 8.38 6.8 1 4227 0.20 300 0 6000 20 6.3 6.8 34 26700 0.1 300 2 310 4.67 6.8 172 118 * Aluminum Pipe Alloy 6063-T6 or 6061-T6 in Schedule and ; Alloy 6063-T6 in Schedule 30, 20, and. R = ot recoended COLUM 1: Victaulic couplings are identified by nominal pipe size. COLUM 2: pipe wall thickness. COLUM 3: Pipe wall thickness schedule as established in ASI Standard B36, -70. COLUM 4: torque required for installing Victaulic plain end couplings to achieve pressure ratings listed in Column and Permissible Maximum s listed in Column 6. TORQUE RATIGS MUST BE APPLIED AT ISTALLATIO. COLUM : Maximum line pressure, including surge, to which a joint should be subjected, based on couplings assembled to full torque specifications on plain end or beveled end standard weight steel pipe and/or Victaulic plain end fittings. pressure ratings are based on pipe prepared in accordance with Victaulic specifications. COLUM 6: Maximum end load from all internal and/or external forces to which the joint should be subjected based on couplings assembled to full torque specifications. OTE: Roust-A-Bout couplings, when sufficiently pressurized, will allow pipe to separate slightly as grips set into pipe. For properly assembled and torqued couplings, this separation should not exceed ¼''/6.4. This should be considered for installations in tightly confined areas. Style 99 couplings are not designed to provide linear or angular movement. ROUST-A-BOUT COUPLIGS ARE DESIGED FOR USE WITH PLAI ED OR BEVELED ED PIPE AD VICTAULIC PLAI ED FITTIGS OLY. Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _
ISTALLATIO Reference should always be made to the I-0 Victaulic Field Installation Handbook for the product you are installing. Handbooks are included with each shipment of Victaulic products for complete installation and assembly data, and are available in PDF format on our website at. WARRATY Refer to the Warranty section of the current Price List or contact Victaulic for details. OTE This product shall be manufactured by Victaulic or to Victaulic specifications. All products to be installed in accordance with current Victaulic installation/assembly instructions. Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations. Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 _11
Tel. +31-1-261.09.00 Fax. +31-1-261.62.89 WCAS-6UPKCK For complete contact information, visit 1671 REV H UPDATED 3/2007