Privacy Cover " patent pending

42 Toilet Partition Privacy Covers NEW HOT ITEM Features: Eliminates most door and panel gaps. Assures personal privacy. " Privacy Cover " patent pending Self-adhesive for fastener free installation. Clear rigid vinyl blends to all partition colors and materials. Cut to fit for various partition door installations. Flexible vinyl flap adapts to multiple applications. The smoke/opaque color and serrated surface obscures vision. Contents: 2) 58" pieces per set (poly bagged) / 5 sets per carton Tools Required: 9A1010 Pencil; Measuring tape; Isopropyl rubbing Alcohol; Multi-purpose Snips and Diagonal pliers PRIVACY COVERS Easy Installation: For door gap applications (apply to post ONLY) A) Latch side: Measure from top of door to top of strike / keeper, then measure from bottom of strike / keeper to bottom of door. Pre-Cut the Privacy Cover with either (Multi-Purpose Snips, Diagonal Pliers or other safe cutting device) to the above measurements and align the cover to the post. Clean up the rough edges with a utility knife or fine grade sandpaper if necessary. Always place the cover on the side opposite to the direction of the door opening. Clean surface of post, where the Privacy Cover is to be mounted, with (isopropyl) rubbing alcohol. Do Not Use Household Cleaners. Remove adhesive backing from flat surface of the cover. Use Locator Tab to assist in placement. Press firmly to the post and apply pressure, using an up and down motion to set the adhesive. Toilet partition doors may be hinged with different style hinges, installation will vary slightly, but cover will always be placed on the post side opposite to the direction of door opening. B) Hinge Side: Pivot Hinge: Measure from top of door to top of top hinge, and then measure from bottom of the top hinge to top of bottom hinge. Usually it will not be necessary to place Privacy Cover below the bottom hinge. Surface Hinge: Measure door from top to the bottom. Hold Privacy Cover to post and determine if adhesive surface will make contact with the hinge fastener heads. If this condition exists, merely cut out a wedge of material at the point of contact with the fastener heads to allow the cover to make an unhindered flat contact to the post. NOTE: Use the same cutting, prepping and application directions as indicated under Latch Side. 42 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Toilet Partition Design 43 For Quotes on Complete Partitions FOR A QUICK RESPONSE ON PARTITION QUOTES PLEASE: Visit our website for blank templates in the design center link in the toilet partition home page. Fax us the Overhead Drawing to 800-642-2406 OR email to contact@robertbrooke.com Materials Five are available POWDER COATED STEEL The industry standard. Most economical hybrid epoxy/ polyester powder coated finish over galvanized steel with honeycomb core. PLASTIC LAMINATE Aesthetic appeal and economy. Pressure laminate smooth surface, resistant to grease and stains. OVERHEAD BRACED/FLOOR ANCHORED Units are recommended for heavy traffic and necessary vandalism-proof areas. Most economical. Anodized aluminum goes around top. They do not require any special floor construction, therefore they can be used in old or new buildings. Styles Four are available SOLID PLASTIC The choice for busy public facilities, high density polyethyene (HDPE) polymer is highly resistant to stains, common acids and cleaning agents, as well as moisture, steam, and corrosion. Will not easily dent or chip. STAINLESS STEEL Gleaming beauty provides exceptional durability and modern styling. Available in #4 satin or textured finish. PHENOLIC - BLACK CORE Impact, moisture, and corrosion resistant, the surfaces are smooth and easy to clean. Ideal for extreme moisture conditions in showers, pools, and saunas, or when maintenance includes hosing down washrooms. FLOOR MOUNTED Absence of top structure prompts the use of these units in low ceiling areas. Gives modern, contemporary appearance. They require a 3" minimum concrete floor construction to secure anchor bolts. TOILET PARTITION DESIGN FLOOR-TO-CEILING ANCHORED Better than overhead braced for heavy traffic and vandalism-proof areas. Most stable as pilasters are anchored into concrete floor and structural ceiling support. CEILING HUNG Ceiling Hung is the best choice where minimizing maintenance is of primary importance. They provide a floor area free from obstruction to speed maintenance. However this design requires structural steel supports in the ceiling. In-a-Corner Layout Examples Between 2 Walls Free Standing Alcove 61" MINIMUM FOR ADA FLOOR MOUNTED OVERHEAD BRACED Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 43

44 Powder Coated Steel Partitions Complete Restroom Stalls Very economical and often used. Finish is a hard hybrid epoxy/polyester powder coated finish over rust resistant phosphate treated steel. With inner honeycomb core bonded to the steel with a non-toxic adhesive to ensure solid construction and sound attenuation. Assembled with a continuous roll-formed interlocking crown molding, with corners brazed and ground smooth. Doors, panels and urinal screens 1" thick, 22 gauge steel. Doors and panels are 58" high. Pilasters 1-1/4" thick, 20 gauge steel. Hardware Cam action hinge permits door to remain at desired position when not in use. Hinges, strike and keeper, coat hook, latch, and bracket s are chrome plated alloy. Concealed latch assembly allows for emergency access. Pilaster shoes are 304 stainless steel. Installation instructions, all mounting hardware and a can of touch up paint are supplied with each order. Available Colors Privacy/Urinal Screens Powder Coated Baked Enamel Global All Orders Ship in 48 hours. White #2129 Grey #2125 Charcoal #2123 Almond #2103 Khaki #2115 Dark Khaki #2109 WALL HUNG 1" thick by 42" high panel. Available in the following widths 12, 18, 24 and 30". Specify color and 9SWHS-XX (where XX is the screen width. PLASTIC LAMINATED PARTITIONS Red #2145 Burgundy #2148 Sage #2141 Azure #2101 Royal Blue #2135 Metallic Silver #2171 Hadrian 535 Light Grey ANTI-GRAFFITI COLORS (SUBJECT TO UPCHARGE) Sandy Beach #2150 Pepper Dust #3590 Includes: Hinges and All Hardware Available for the following door opening widths (actual door size is 3/8" narrower than the opening): 20, 22, 24, 26, 28, 30, 32, 34, 36". Color 9TDS-XX (where XX is door opening width) Pilaster type Standard round edge, square edge or mounted on flat wall Includes: 4 Brackets Available in the following widths: 16, 22, 28, 34, 40, 46, 52, 55, 58, 60, 70 and 76". Actual width is 1/2" less. Color, 9TPS-XX (where XX is panel width). Reinforcing for grab bars available. Request a Manufacturer's color charts for more accurate color representation Replacement Includes: Brackets & Stainless Steel Shoes Available in the following widths: 2, 3, 4, 5, 6, 7, 8, 10, 12, 16, 18, 20, 22 and 24". Color, 9TLS-XX (where XX is pilaster width) Overhead braced for 82" length, floor braced for 70" length, wall hung for 58" high, ceiling hung for 84" length, and floor-to-ceiling for up to 120" maximum length. FLOOR & CEILING BRACED POST & PANEL 1-3/4" square post up to 120" maximum with 58" high panel. Specify color, 9SFCS- XX-Y (where XX is width from the front of the post to the wall, Y = floor-to-ceiling height)* OVERHEAD BRACED / FLOOR ANCHORED Pilaster is braced by headrail to wall. Panel is 58" high. Pilaster is 82" high. Specify color and Part No.9S0BS-XX (where XX is width from the front of the pilaster to the wall*). Floor Anchored 70" high pilaster and 58" high panel. Specify color and Part No.9SFAS-XX (where XX is width from the front of the pilaster to the wall).* * The overall width of the screen is 2" wider than the width of the panel. Doors Panels Pilasters Aluminum Headrail Available in the following lengths: 65" or 83". And for 1" and 1-1/4" thick pilasters. Specify 9THS-XX-Y (where XX is length and Y is pilaster thickness). 1-1/4" Wide Pilaster, Anti-grip type. Has 1/4" slot for curtain. 44 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. Black #2127 Ships within 48 hrs of Order. All Other Colors Ship in 2 to 3 weeks. 541 Extra White 603 Almond 607 Bordeaux 621 Slate 504 Linen 532 Latte 576 Ruby Red 545 Charcoal 500 White 585 Sahara 581 Moss Green 510 Black 639 Sapphire Blue 609 Colonial Blue SPECIAL EFFECTS COLORS (SUBJECT TO UPCHARGE) 833 Tricorn Black 828 Dovetail 829 Desert 837 Black Fox 831 Nickel Metallic 814 Cast Iron Metallic 826 Kilim Beige Headrail braced solid plastic toilet partitions stocked in the U.S.A. and Canada.

Plastic Laminated Partitions 45 Complete Restroom Stalls Gives a more aesthetic appeal while maintaining economy. Fabricated from 45 pound density, resin impregnated particle board. Plastic laminate is glued to particle board with a nontoxic, water resistant adhesive under high pressure. Components are edge banded prior to face lamination to ensure moisture run-off and vandal resistance. Not recommended for high moisture areas. Doors, panels and urinal screens 1" thick (uses 7/8" particle board) Pilasters 1-1/4" thick (uses 1-1/8" particle board) Hardware Gravity cam-action hinges permit door to remain at desired position when not in use. Hinges, strike and keeper, coat hook, latch and brackets are chromed plated alloy. Door can be lifted to allow emergency access. Installation instructions and all mounting hardware are supplied with each order. Includes: Hinges and All Hardware Available for the following door opening widths (actual door size is 3/8" narrower than the opening) 22, 24, 26, 28, 30, 32, 34, and 36" Color 9TDL-XX (where XX is door opening width) Includes: 4 Brackets Available in the following widths: 16, 22, 28, 34, 40, 46, 52, 55, 58, 60, 70 and 76". Actual width is 1/2" less. Color, 9TPL-XX (where XX is panel width). Replacement Doors Panels Pilasters Aluminum Headrail Includes: Brackets & Stainless Steel Shoes Available in the following widths: 3, 4, 5, 6, 7, 8, 10, 12, 16, 18, 20, 22 and 24". Color, 9TLL-XX (where XX is pilaster width) Overhead braced for 80" length, wall hung for 55" length and floor-to-ceiling for up to 116" maximum length. Available in the following lengths: 65" or 83". And for 1" and 1-1/4" thick pilasters. Specify 9THL-XX-Y (where XX is length and Y is pilaster thickness). 1-1/4" Wide Pilaster, Anti-grip type. Has 1/4" slot for curtain. Privacy/Urinal Screens Global Plastic Laminate Colors - ALL Colors Ship 1 Week WALL HUNG 1" thick by 42" high panel. Available in the following widths 12, 18, 24 and 30". Specify color and 9SWHL-XX (where XX is the screen width. FLOOR & CEILING BRACED POST & PANEL 1-3/4" square post up to 120" maximum with 58" high panel. Specify color, 9SFCL-XX-Y (where XX is width from the front of the post to the wall, Y = floor-toceiling height)* OVERHEAD BRACED / FLOOR ANCHORED Pilaster is braced by headrail to wall. Panel is 58" high. Pilaster is 82" high. Specify color and 9S0BL-XX (where XX is width from the front of the pilaster to the wall*). * Directional Panel - Pattern on panels over 60" wide will run perpendicular to pattern on doors and pilasters. POWDER COATED PARTITIONS Floor Anchored 70" high pilaster and 58" high panel. Specify color and 9SFAL-XX (where XX is width from the front of the pilaster to the wall).* * The overall width of the screen is 2" wider than the width of the panel. Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 45

46 Solid Polymer Plastic Partitions Complete Restroom Stalls Designed for high-traffic public facilities, parks and schools. The high-density polyethylene material has homogenous color throughout each component. Self-lubricating surface resists markings from pens, pencils, etc. Has low maintenance; good durability; water resistant, unaffected by steam or high humidity. Available in overhead braced/floor anchored and floor-to-ceiling anchored only. Doors, panels, pilasters and urinal screens 1" thick, doors and panels are 55" high. Privacy/Urinal Screens Hardware Available in hidden integral hinges or wrap around vaulttype hinges. Cam-action hinge permits door to remain at desired position when not in use. Slide latch, striker and keeper, and coat hook are chrome plated alloy. Slide latch assembly allows for emergency access. Standard brackets are 54" long extruded PVC colored to match partitions. Pilaster shoes are molded plastic to match partitions. Stainless steel shoes and full height aluminum brackets are available at no up charge. Installation instructions and all mounting hardware are supplied with each order. Available Colors WALL HUNG 1" thick by 42" high panel. Available in the following widths 12, 18, 24 and 30". Specify color and Part No.9SWHP-XX (where XX is the screen width. Hadrian Solid Plastic 1 week shipping High Density Polyethylene Colors (HDPE) Global Solid Polymer Plastic All COLORS SHIP IN 48 hours STAINLESS STEEL PARTITIONS FLOOR & CEILING BRACED POST & PANEL 1-3/4" square post up to 120" maximum with 55" high panel. Specify color, 9SFCP-XX-Y (where XX is width from the front of the post to the wall, Y = floor-toceiling height)* OVERHEAD BRACED / FLOOR ANCHORED Pilaster is braced by headrail to wall. Panel is 55" high. Pilaster is 82" high. Specify color and 9S0BP- XX (where XX is width from the front of the pilaster to the wall*). * The overall width of the screen is 2" wider than the width of the panel. Request Manufacturer's color charts for more accurate color representation Headrail braced solid plastic toilet partitions stocked in the U.S.A. Replacement * NOT Available in tough Texture TM or Hammered Finishes Doors Panels Pilasters Aluminum Headrail Includes: Hinges and All Hardware Available for the following door opening widths (actual door size is 3/8" narrower than the opening): 20, 22, 24, 26, 28, 30, 32, 34, 36". Color 9TDP-XX (where XX is door opening width) Pilaster type Standard round edge, square edge or mounted on flat wall Includes: 4 Brackets Available in the following widths: 16, 22, 28, 34, 40, 46, 52, 55, 58, 60, 70 and 76". Actual width is 1/2" less. Color, 9TPP-XX (where XX is panel width). Reinforcing for grab bars available. Includes: Brackets & Stainless Steel Shoes Available in the following widths: 3, 4, 5, 6, 7, 8, 10, 12, 16, 18, 20, 22 and 24". Color, 9TLP-XX (where XX is pilaster width) Overhead braced for 82" length, floor braced for 70" length, wall hung for 58" high, ceiling hung for 84" length, and floor-to-ceiling for up to 120" maximum length. Available in the following lengths: 65" or 83". And for 1" and 1-1/4" thick pilasters. Specify 9THP-XX-Y (where XX is length and Y is pilaster thickness). 1-1/4" Wide Pilaster, Anti-grip type. Has 1/4" slot for curtain. 46 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Stainless Steel Partitions 47 Complete Restroom Stalls Provides gleaming beauty, exceptional durability and modern styling. Type 304 stainless steel with a #4 finish bonded to an inner honeycomb core under pressure with a non-toxic adhesive to ensure solid construction and sound attenuation. Assembled with continuous rollformed interlocking, 22 gauge stainless steel crown molding, with corners welded and ground smooth. Doors, panels and urinal screens 1" thick, 22 gauge stainless steel. Pilasters 1-1/4" thick, 22 gauge stainless steel. Hardware Cam-action hinges permit door to remain at desired position when not in use. Hinges, strike and keeper, coat hook and latch are chrome plated alloy. Concealed latch allows for emergency access. Installation instructions and all mounting hardware are supplied with each order. Privacy/Urinal Screens WALL HUNG 1" thick by 42" high panel. Available in the following widths 12, 18, 24 and 30". Specify color and Part No.9SWHSS-XX (where XX is the screen width. FLOOR & CEILING BRACED POST & PANEL 1-3/4" square post up to 120" maximum with 58" high panel. Specify color, 9SFCSS-XX-Y (where XX is width from the front of the post to the wall, Y = floor-toceiling height)* OVERHEAD BRACED / FLOOR ANCHORED Pilaster is braced by headrail to wall. Panel is 58" high. Pilaster is 82" high. color and Part No.9S0BSS-XX (where XX is width from the front of the pilaster to the wall*). Floor Anchored 70" high pilaster and 58" high panel. Specify color and 9SFASS- XX (where XX is width from the front of the pilaster to the wall).* * The overall width of the screen is 2" wider than the width of the panel. Cover panels or screens near urinal. Stainless steel. Attach with rivets. Urinal Splash Plates Stainless Steel HEIGHT WIDTH 41" 16" 9TUSP16 41" 22-1/2" 9TUSP22 36" 24" 9TUSP24 36" 30" 9TUSP30 36" 36" 9TUSP36 Replacement Doors Panels Pilasters Aluminum Headrail Includes: Hinges and All Hardware Available for the following door opening widths (actual door size is 3/8" narrower than the opening): 20, 22, 24, 26, 28, 30, 32, 34, 36". Color 9TDSS-XX (where XX is door opening width) Pilaster type Standard round edge, square edge or mounted on flat wall Includes: 4 Brackets Available in the following widths: 16, 22, 28, 34, 40, 46, 52, 55, 58, 60, 70 and 76". Actual width is 1/2" less. Color, 9TPSS-XX (where XX is panel width). Reinforcing for grab bars available. Includes: Brackets & Stainless Steel Shoes Available in the following widths: 2, 3, 4, 5, 6, 7, 8, 10, 12, 16, 18, 20, 22 and 24". Color, 9TLSS-XX (where XX is pilaster width) Overhead braced for 82" length, floor braced for 70" length, wall hung for 58" high, ceiling hung for 84" length, and floor-to-ceiling for up to 120" maximum length. Available in the following lengths: 65" or 83". And for 1" and 1-1/4" thick pilasters. Specify 9THSS-XX-Y (where XX is length and Y is pilaster thickness). 1-1/4" Wide Pilaster, Anti-grip type. Has 1/4" slot for curtain. SOLID POLYMER PLASTIC PARTITIONS Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 47

48 Solid Phenolic Partitions Complete Restroom Stalls Ideal for extreme moisture conditions in showers, pools and saunas. Surfaces are smooth and easy to clean. Phenolic material is comprised of multiple layers of melamine resin impregnated kraft paper to give a black core and a decorated surface sheet on both faces. All layers are fused together under high pressure. Material of choice where durability and strength are required. Uses stainless steel brackets. Impact and corrosion resistant; does not support bacteria. Doors and pilasters 3/4" thick Panels and urinal screens 1/2" thick Hardware Cam-action hinge permits doors to return to a preset position when not locked. Hinges, strike and keeper are brushed aluminum. Camaction hinge allows emergency access by lifting door. Installation instructions and all mounting hardware are supplied with each order. Replacement SOLID PHENOLIC PARTITIONS Doors Panels Pilasters Aluminum Headrail Includes: Hinges and All Hardware Available for the following door opening widths (actual door size is 3/8" narrower than the opening): 20, 22, 24, 26, 28, 30, 32, 34, 36". Color 9TDPH-XX (where XX is door opening width) Pilaster type Standard round edge, square edge or mounted on flat wall "Color-Thru" Phenolic Cinnamon 5450C Persian Blue 7450C Gray Misy 3450C Sage 6450C Standard Black Core Colors Hazelnut 4450C Includes: 4 Brackets Available in the following widths: 16, 22, 28, 34, 40, 46, 52, 55, 58, 60, 70 and 76". Actual width is 1/2" less. Color, 9TPPH-XX (where XX is panel width). Reinforcing for grab bars available. Global Solid Phenolic Colors - ALL Colors Ship in 1-2 Weeks Black 2000C Almond 4000 Neutral Glace 1130 Natural Canvas 4410 Includes: Brackets & Stainless Steel Shoes Available in the following widths: 2, 3, 4, 5, 6, 7, 8, 10, 12, 16, 18, 20, 22 and 24". Color, 9TLPH-XX (where XX is pilaster width) Overhead braced for 82" length, floor braced for 70" length, wall hung for 58" high, ceiling hung for 84" length, and floor-to-ceiling for up to 120" maximum length. Available in the following lengths: 65" or 83". And for 1" and 1-1/4" thick pilasters. Specify 9THPH-XX-Y (where XX is length and Y is pilaster thickness). 1-1/4" Wide Pilaster, Anti-grip type. Has 1/4" slot for curtain. Desert Zephyr 4583 Tungsten EV 4801 Taupe 9096 Silver Gray 3000 Folkstone Celesta 3300 Dove Gray 3010 Graphite Grafix 3020 Request Manufacturer's color charts for more accurate color representation 48 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Grab Bars 49 ADA ACCESSIBLE COMPARTMENT REQUIRE: 1-1/4" or 1-1/2" Dia. bars, at least a 42" long on side and at least a 36" long behind the toilet. (Most popular are 36" and 42" long, 1-1/2" diameter, concealed set screws.) In compliance with strength requirements of ADA guidelines. Bars are fabricated of a satin finish 18 Gauge type 304 stainless steel tubing. Available peened or smooth. Mandrell bending process ensures uniform bar diameters. Heliarc welding forms a single structural unit. STRAIGHT BARS LENGTH K7410 12" K7411 16" K7412 18" K7413 24" STRAIGHT BARS WITH CENTER POST LENGTH K7415C 42" K7416C 36" K7417C 48" TOILET PARTITION BARS LENGTH K74183 52" K74184 54" STRAIGHT BARS LENGTH K7414 32" K7415 42" K7416 36" K7417 48" Specify Part Number, Flange Type, 1-1/4" or 1-1/2" Diameter when ordering Choose One of 3 Flange Types EXPOSED MOUNTING Flange is 3" diameter, 1/8" thick type 304 stainless steel with satin finish. Exposed mounting screw holes are drilled and countersunk. SNAP FLANGE Cover snaps over mounting flange dimples to conceal screws. Concealed mounting flange is 3-1/8" O.D. diameter with two screw holes and three locking dimples and is 1/8" thick, type 304 stainless steel. Cover is type 304 stainless steel with satin finish, 22 gauge, 3-3/16" diameter. CONCEALED MOUNTING Flange is 3" diameter. 1/2" deep, 11 gauge type 304 stainless steel with satin finish. Tenon plate is 13 gauge with slotted screw holes. Flange is secured to tenon plate with 3 stainless steel allen head screws. Grab Bars for Toilet Stools 32" Left Hand (shown), Right Hand opposite Model No. 2210 21" 30" Left Hand (shown), Model No. 2257 Right Hand, Model No. 2256 Left Hand (shown), Model No. 2245L Right Hand, Model No. 2245R 12" 16" Left Hand (shown), Model No. 2231 MODEL LENGTH 7450 A = 36" B = 24" 7456 A = 36" B = 54" 7457 A = 42" B = 52" 7460 A = 18" B = 30" GRAB BARS 5" SWING-UP GRAB BAR Locks firmly into place when lifted into an upright position 1-1/4" O.D. Model No. 3410 SIDE-GRAB BAR Model No. 7472 30" Swings 90 24" 24" TYPE 34 Model No. 2234 18" 33" Adjustable 8" 30" More styles also available Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 49

50 Restroom Accessories ROLL TYPE CHROME 9A0330 Headrail Type "A" DOUBLE ROLL CHROME 9A0965 Specification Sheet, Other Models & Types Available Headrail Type "B" SINGLE ROLL Deluxe CHROME 9AT815 TYPE "A" INSIDE PILASTERS/ OVER PANEL PILASTER THICKNESS LENGTH 1" 60" 9HR60A 1" 74" 9HR74A 1" 120" 9HR120A T-Paper Holders FOR 4 1/2" wide Rolls ONLY DOUBLE ROLL Deluxe CHROME 9AT830 TYPE "B" OVER PILASTERS PILASTER THICKNESS LENGTH 1" 75" 9HR75B1 120" 9HR12B1 1-1/4" 62" 9HR62B2 75" 9HR75B2 98" 9HR98B2 120" 9HR12B2 RESTROOM ACCESSORIES SINGLE ROLL TYPE CONTROL-O-ROL Controlled Tissue Flow. Tough ABS Plastic. Tension Spring 9A0270 COLOR Powder Gray Ivory White Diaper Depot Changing Station HANDICAPPED adds Lift 9RSS1P 9RSS1I 9RSS1W DOUBLE ROLL TYPE CONTROL-O-ROL Controlled Tissue Flow. Tough ABS Plastic. Tension Spring 9A2270 SPINDLE ONLY CONTROL-O-ROL ABS PLASTIC 9A3469 Baby Changing Station 9R104 Surface Mounted 4" Depth (closed) ADA Compliant Sturdy Child Protection 250 lb. load capacity Easy Opening and Closing Constructed of 100% High-density Polyethylene Easily cleaned, gray color Attractive, durable, safe, affordable Combines durability with long lasting looks Universal Safety instructions Dual dispensers for liners 4" depth closed; 20" depth open; 34" wide Fully hidden gas shock Shelf for personal changing items Safe Strap safety belt Molded in hook for purse or diaper bag Concave bed Includes Industrial grade hardware kit for easy installation Warranted to be free from defects in material and workmanship for up to five years DOUBLE ROLL TYPE with Covered Reverse Roll Controlled by Lock 6" x 10" x 5-5/8" CHROME 9A0876 SEAT ATTACHING HOLES N/A CABINET TYPE (Sheet) 8-1/4" x 5-7/8" x 3-1/8" WHITE 9A331W 9" Jumbo Rolls Universal All Brand 9" Jumbo Tissue with 3-3/8" Cores White Impact Resitant Plastic Back STAINLESS STEEL ALSO AVAILABLE SINGLE FRONT COLOR DARK TRANSLUCENT 9AR26T WHITE 9AR26W Toilet Seats KEYED 2 ROLL TYPE Surface Mounted with Keyed Lock 6"w x 13"h x 6"d Stainless Steel 9A0311 Heavy White Metal Back White Plastic Front 9AR25W Heavy Black Metal Back Transparent Plastic Front 9AR25T REPLACEMENT SPINDLE (Used on the 9A0311) 5-5/16" Long x 7/16" Axle Dia. 9A0312 TWIN FRONT COLOR DARK TRANSLUCENT 9AR27T WHITE 9AR27W Solid Colored Plastic Heavy Duty For Commercial & Institutional Use. NON-HANDICAPPED A LENGTH B WIDTH COVER COLOR* PART N0. ELONGATED BOWL 18-3/8 14-1/8" YES WHITE 9ASE10 15-1/4" NO WHITE 9ASE20 BLACK 9ASE30 REGULAR BOWL 16-3/4 14-1/2" YES WHITE 9ASE40 15" NO WHITE 9ASE50 BLACK 9ASE60 HANDICAPPED LIFT B Cover Width Color* 2" Elongated No White 9ASE70 3" Elongated No White 9ASE75 50 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Restroom Accessories 51 Soap Dispensers Specification Sheet, Other Models & Types Available EYE GLASS REPLACEMENT for the 300/400 series soap deispensers 9A0300E PLASTIC LIQUID/LOTION SOAP DISPENSER Impact Resistant Dark Translucent Plastic Large Push Bar Meets ADA Requirements 5"w x 6"h x 4"d CAPACITY 30 oz 9AS30T 46 oz 9AS46T TOUCH-FREE UNIVERSAL ELECTRONIC SOAP DISPENSER Impact Resistant 3-Cell Alkaline Batteries Provide 10,000 Dispenses of 1 Drop of Soap Hand actuates by breaking electronic beam 4"w x 11"h x 5"d 27 oz. Capacity 9SE800W PUSH UP SOAP DISPENSER White Plastic Globe Liquid Soap 4"w x 6"h x 5"d 16 oz. Capacity 9A0500 STAINLESS STEEL VERTICAL SOAP DISPENSER 5"w x 8"h x 3"d 40 oz. Capacity SOAP LIQUID 9A0444 STAINLESS STEEL HORIZONTAL SOAP DISPENSER 8"w x 5"h x 3"d 40 oz. Capacity SOAP LIQUID 9A0333 Soap Dispenser Valve Assemblies STAINLESS STEEL VERTICAL ALL PURPOSE SOAP DISPENSER For both Liquid & Lotion Soaps 5"w x 8"h x 5"d 40 oz. Capacity 9A0347 LAVATORY MOUNTED SOAP DISPENSER Dispenses Viscous Lotion Soaps and synthetic detergents Spout & Stem are Polished Stainless Steel 34 oz. Capacity 9A0332 Sanisuds Soap Dispensers 1200 ml refill high capacity refill reduces labor & reduces waste Sensor technology provides RELIABLE touchfree dispensing Battery life of 45,000 uses or one year Premeasured dispensing saves soap Modern design enhances any facility Hygienic-fresh valve with every refill Touchless application helps reduce cross contamination Over 3,000 hand washes per refill LED light for low battery 3 year warranty Mounts to wall with screws and anchors or double-sided tape Battery requirements: Six "AA" alkaline batteries Helps reduce 50% per hand wash with the perfect portion of high concentrated soap One of the GREENEST systems available with a controlled delivery, reduced packaging, long battery life, biodegrable, and more hand washes per refill STAINLESS STEEL HORIZONTAL ALL PURPOSE SOAP DISPENSER For both Liquid & Lotion Soaps 8"w x 5"h x 5"d 40 oz. Capacity 9A0345 SURFACE MOUNTED SHELF AND SOAP DISPENSER For both Liquid & Lotion Soaps Satin Finish Stainless Steel 20"w x 3"h x 5"d 80 oz. Capacity 9A0318 SANISUDS DISPENSER Black Translucent 4-3/4" x 11-1/4" 9SF305BK SANISUDS DISPENSER Blue Translucent 4-3/4" x 11-1/4" 9SF305ICE SANISUDS DISPENSER Brown Black Translucent 4-3/4" x 11-1/4" 9SF305TS *Valve threads are 3/4" O.D. 28 Threads per inch. SOAP DISPENSER 9A0333 9A0444 9A0500 ALL PURPOSE Disposable Toilet Seat Covers and Dispensers DISPENSERS 250 Seat Cover Capacity GREEN SEAL CERTIFIED LOTION FOAM SOAP 3 packs per case 9F7000 SURFACE MOUNTED UNKEYED 12" x 17" x 2" White 9ASE01 Polished Chrome 9ASE02 Stainless Steel 9ASE03 Sanisuds Soap Refills NON-ALCOHOL FOAM SANITIZER 3 packs per case 9F7500 ANTIBACTERIAL FOAM SOAP W/TRICLOSAN 3 packs per case 9F7125 VALVE 9A035C* 9A035C* 9AV500 9AV320 RECESSED KEYED 18" X 21"X 3" Stainless Steel 9ASE04 COVERS 18" x 15" Bright White 2500 Case Size 9ASE11 5000 Case Size 9ASE12 E-2 FOAM CLEANSER 3 packs per case 9F7250 ALCOHOL FOAM SANITIZER 3 packs per case 9F7800 RESTROOM ACCESSORIES Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 51

52 Restroom Accessories SINGLE FOLD PAPER TOWEL DISPENSER Holds 400 Towels Sheet Metal Construction 11"w x 6"h x 5"d ITEM WHITE CHROME 9AT500 9AT500C C-FOLD, MULTI-FOLD SMALL METAL PAPER TOWEL DISPENSER Tumbler Lock, Stainless Steel and Heavy Duty Piano Hinge Holds 275 Multi-fold or 200 C-fold Towels 11"w x 8"h x 4"d 9AT0215 ROLL TYPE - BOTTOM PULL TOWEL DISPENSER #4 Satin Finish Type 304 Stainless Steel Exposed Towel Allows User to Pull Out Predetermined Amount of Towel and Tear Off Holds Rolls up to 8"wide non-perforated roll 11"w x 16"h x 9"d 9AU170HF ROLL TYPE, CRANK TOWEL DISPENSER Holds Rolls 8"w x 500' Dent Resistant White Enamel Steel 9AT675 Paper Towel Dispensers C-FOLD, MULTI-FOLD PAPER TOWEL DISPENSER Heavy Gauge Steel Back with Impact Resistant Plastic Front Holds 540 Multi-fold or 335 C-fold Towels 11"w x 15"h x 4"d COVER COLOR WHITE DARK TRANSLUCENT 9AT175W 9AT175T C-FOLD, MULTI-FOLD METAL PAPER TOWEL DISPENSER Tumbler Lock, Sheet Metal and Heavy Duty Piano Hinge Holds 525 Multi-fold or 400 C-fold Towels 11"w x 15"h x 4"d ITEM WHITE ENAMEL CHROME PLATED STAINLESS STEEL ROLL TYPE - FULL WIDTH LEVER ACTION TOWEL DISPENSER Heavy Gauge Steel Back with Impact Resistant Plastic Front For Rolls 8"w x 8" dia. 11" w x 16"h x 9"d COVER COLOR WHITE 9AT215W DARK TRANSLUCENT 9AT215T 9AT130 9AT130C 9AT0210 ROLL TYPE - NO TOUCH ELECTRIC TOWEL DISPENSER Heavy Gauge Steel Back with Impact Resistant Plastic Front For Rolls 8"w x 8" dia. Towels are Dispensed Automatically When Hands are Placed Below Dispenser 11"w x 16"h x 9"d COVER COLOR Towel Cabinet DARK TRANSLUCENT 9AT225T Selector Guide RESTROOM ACCESSORIES ROLL TYPE - BOTTOM PULL TOWEL DISPENSER Translucent Impact Resistant Plastic Front For Rolls 8"w x 8" dia. 11" Sheet via. Auto-Cut Mechanism 11"w x 16"h x 9"d 9AT400T HEAVY DUTY NO TOUCH HAND/HAIR DRYER Tough Die-cast Aluminum Housing with Baked Enamel Finish 2300 Watts of Power Surface or Recessed Mounted 13"w x 9"h x 7"d 5 Year Warranty HOUSING BAKED ENAMEL STAINLESS STEEL CHROME PLATED NO TOUCH 9U1525EA 9U1521EA 9U1525CEA HANDS FREE METAL AUTO HAND DRYER Painted Cast Aluminum Approximate drying time of 30 sec. Dryer shall deliver 150 CFM Sound level: 64dB Volts: 120 11-3/16" X 9-3/4" X 8" 9HD907 Electric Air Dryer ROLL TYPE - SELF-ADJUSTING CENTER PULL DISPENSER Impact Resistant Plastic Holds Rolls up to 9"dia x 9" tall 10"w x 12"h x 10"d COVER COLOR WHITE DARK TRANSLUCENT TURBO DRI HIGH SPEED DRYER Heavy Duty Stailess Steel Housing Infrared sensor 12 second dry time 60 second shut off 120 Thru 240 Voltage Surface Mounted Sound level: 65dB to 78dB 8-1/16"w x 12"h x 7-5/64"d ITEM WHITE SATIN SS BRIGHT SS HANDS FREE ABS PLASTIC HAND DRYER High grade fire retardant ABS Approximate drying time 30 sec. Power cut off automatically in case of irregular use 120 sec Dryer shall deliver 150 CFM Volts: 120 10-1/2" X 8-3/4" X 6-3/4" 9HD903 9A0197W 9A0197S 9A0197B 9AT255W 9AT255T BLUSTORM HANDSFREE HIGH SPEED DRYER Stainless Steel Less than 10-15 sec. dry time Blue light allows user to maximize the dryers efficience One piece cover with 2 vandalproof lock screws & key wrench Over a 70% cost savings vs. conventional hand dryers Power cutoff automatically case of irregular use over 60 sec 5 year warranty 9.1" X 11.9" X 7.4" 9HD950 120 volts 9HD951 240 volts 52 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Restroom Accessories 53 Lexan or Stainless Steel Corner Guards Available in 6 colors: Clear (standard), white, almond, dark almond, gray and black. Stainless steel available in satin or bright finish. Installation options are screws or double-sided tape. PART NUMBER LENGTH WINGS 48" 96" 1-1/8" X 1-1/8" KCG148 KCG196 2-1/2" X 2-1/2" KCG248 KCG296 Specify: part number, material, color and screws or tape installation. Paper Towel Dispensers & Waste Receptacles Specification Sheet, Other Models & Types Available C-FOLD, MULTI FOLD TOWEL DISPENSER & WASTE RECEPTACLE 22 Gauge Type 304 Stainless Steel Heavy Duty Door and Piano Hinge Tumble Lock on Doors and Waste Receptacle 600 C-Fold or 800 Multi Fold Towels Capacity 12 Gallon Waste Receptacle 15"w x 54"h x 4"d ITEM SURFACE MOUNTED SEMI RECESS MOUNTED RECESSED 9A04699 9A04692 9A0469 WASTE RECEPTACLE 22 Gauge Type 304 Stainless Steel Top and Bottom Edges Hammered for Safety 12 Gallon Receptacle. Other Sizes Available ITEM SIZE SURFACE MOUNTED 16"W X 29"H X 7"D 9A04589 FREE STANDING 16"W X 23"H X 8"D 9A0826 RECESSED 16"W X 29"H 9A0458 SURFACE MOUNTED SANITARY NAPKIN DISPOSAL & BAGS Piano Hinge Cover 8"w x 11"h x 4"d ITEM WHITE FINISHED METAL CHROME PLATED METAL STAINLESS STEEL KRAFT (WAX COATED) REFILL BAGS (500 COUNT) 9A4101W 9A4101C 9A4101 9A4101B C-FOLD, MULTI FOLD PAPER TOWEL DISPENSER 22 Gauge Type 304 Stainless Steel Heavy Duty Door and Piano Hinge Tumble Lock on Doors 600 C-Fold or 800 Multi Fold Towels Capacity 13"w x 26"h x 4"d ITEM SURFACE MOUNTED RECESSED 9A05429 9A0452 NOTE: 350 C-Fold / 475 Multi Fold Available Napkin/Tampon Dispensers ITEM PARTITION DUAL ACCESS RECESSED IN-WALL DUAL SANITARY NAPKIN/TAMPON DISPENSER #4 Satin Finish Stainless Steel 2 Seperate/Independant Mechanisms 30 Napkin, 27 Tampon Capacity Settings: Free,.05,.10,.25,.50 coinage ITEM SURFACE MOUNTED RECESSED 9AU527 9AU526 PARTITION & IN-WALL SANITARY NAPKIN/TAMPON DISPOSAL #4 Satin Finish 304 Stainless Steel Partition Unit Serves 2 Compartments Mounting in Panel Recessed for Side Wall Use 9A0472 9A0473 RESTROOM ACCESSORIES Plexiglass with polished edges. 12" Dia. Part Nos. Women 9R840 Men 9R840A Restrooms 9R840BS Restroom 9R840B ADA Braille Directional Signs Pressure sensitive 6"x6" (152 mm) international handicap symbol white on blue 9R840C Tactile signs comply with the signage requirements of the American with Disabilities Act. Durable plastic with Grade 2 Braille. 6"x 8", Part Nos. Women 9R840T Men 9R840AT Restroom 9R840BT Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 53

54 Restroom Accessories Mirrors Also available with shelves CHANNEL FRAME PLATE GLASS MIRROR 1/2" x 1/2" x 1/2" One Piece Channel Type 304 Satin Finish Stainless Steel 15 Year Warranty Against Silver Spoilage Includes bracket for Easy Secure Installation Width Height Width Height 9TM535 16" 20" 9TM655 24" 48" 9TM639 16" 24" 9TM624 24" 60" 9TM550 16" 30" 9TM626 36" 24" 9TM537 18" 24" 9TM660 36" 48" 9TM640 18" 30" 9TM627 48" 24" 9TM541 18" 36" 9TM670 48" 36" 9TM650 24" 24" 9TM628 60" 24" 9TM641 24" 30" 9TM680 60" 36" 9TM623 24" 36" 9TM690 72" 36" FIXED ANGLE TILT MIRROR Offers Visibility for Wheel Chair Users 20 Gauge Satin Finish Stainless Steel Frame Mirror Tapers from 4" at Top to 1" at Bottom 15 Year Warranty Against Silver Spoilage 4 Keyhole Slots in Back of Mirror Unit Connect to Screws in Wall Width Height 9A535 16" 30" 9A5351 18" 24" 9A5353 18" 30" 9A5355 18" 36" 9A5357 24" 30" 9A5359 24" 36" RESTROOM ACCESSORIES Fabricated with Satin Finish Stainless Steel Premium shelves Specification Sheets are available for all products UN-DO-IT For Removing One-Way Screws For #12 & #14 Screws For #8 & #10 Screws For #6 & #8 Screws Three-Pack One of each 9A0810 9A0807 9A0804 9A0801 ADJUSTABLE TILT MIRROR Offers Visibility for Wheel Chair Users or Returns to Upright Position 18 Gauge Stainless Steel Frame Tilts Full 6" 15 Year Warranty Against Silver Spoilage Stainless Steel Hinge Pivot Brackets and Piano Hinge Attached Mirror to Wall Width Height Width Height 9A600T 16" 24" 9A600T5 18" 36" 9A600T1 16" 30" 9A600T7 24" 30" 9A600T2 18" 24" 9A600T9 24" 36" 9A600T3 18" 30" Stainless Steel Shelving ECONOMY SHELVES LENGTH 5" Depth 6" Depth 8" Depth 12" 9TS538x12 9TS638x12 9TS838x12 16" 9TS538x16 9TS638x16 9TS838x16 18" 9TS538x18 9TS638x18 9TS838x18 24" 9TS538x24 9TS638x24 9TS838x24 30" 9TS538x30 9TS638x30 9TS838x30 36" 9TS538x36 9TS638x36 9TS838x36 48" 9TS538x48 9TS638x48 9TS838x48 60" 9TS538x60 9TS638x60 9TS838x60 72" 9TS538x72 9TS638x72 9TS838x72 Toilet Partition Hardware Fasteners One-Way Sheet Metal Screws Chrome Plated Steel Available 100/Box DESCRIPTION USE 9A7022 #10 x 5/8 long - 11/32 dia. Coat Hooks head, 3/16 dia. thread #9F0217 Slide Bolt Latch, #9F0211N & #9F0214N Hinges 9A7087 #10 x 1" long - 3/16" dia., Door Inserts, Cam Housings, Phillips Tapered head Flat Keeper Bumpers 9A7073 #12 x 1-1/2" long 13/32 dia. Bracket to wall head 7/32 dia., thread 9A0121 #12 x 1" Plastic Plug Anchor #9A7073 Screws 9A7040 #14 x 5/8" long 15/32 dia., Bracket to Panel & Bracket to head, 1/4 dia. thread Pilaster #9S7531 Throw Latch 9A7010 #10 x 3" Long 7/16 dia. Attaches brackets to drywallhead toggle FRAMELESS STAINLESS STEEL MIRROR 20 Gauge Stainless Steel Polished to a #8 Mirror Finish 1/4" thick Concealed Tempered Masonite Backing with Holes in Each Corner for Mounting. Customer Supplies Screws Width Height 9A8026 16" 20" 9A80261 16" 24" 9A80262 18" 24" 9A80263 18" 30" 9A80265 24" 30" 9A80267 24" 36" 9A80269 48" 24" FOLDING UTILITY Shelf 9A0698 14-5/8" X 5-13/16" Upright position when not in use. One-way Shoulder Screw & Barrel Nut 10-24 Thread GRIP RANGE 9SS075 3/4" 7/8" 9SS087 7/8" 1-1/16" 9SS106 1-1/16" 1-5/16" 1" door slide bolt latches 1" panel brackets 9SS131 1-5/16" 1-5/8"1-1/4" Pilaster brackets, keeper bumpers & hinges 54 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Toilet Partition Hardware 55 For use on Metal Accurate Chrome Plated Hardware For use on Plastic Laminate A = 1-1/2" CAM BOTTOM 9HAH6 PIN 9HAH11 9HACL1 Chrome Plated 9HACL1SS Cast SS ACCURATE DOOR KIT NEW STYLE TURN LATCH & COVER 9HACL3A6N Chrome Plated 9HACL3ASS6N Cast SS Used January 1 2013 to current. Includes all parts shown and security screws. 9HACL505 Chrome Plated 9AA102 A = 1-5/8" LATCH COVER & KNOB 9AA104C TOP AND SET 9HAH15 A = 1-1/2" BOLT 9HAH5 How to Identify Hardware Top and Bottom hinges are more easily identified by measuring the distance "A" on your hinge and comparing it to "A" next to the part. Screws Are Supplied with All Hardware For use on Metal 9AA105 LATCH COVER & KNOB 9AA104A CAM TOP 9HAH7 DOOR INSERT CLOSURE CAP 9HAH3 BOLT LATCH SLIDE PIN 9HACL5 COAT HOOK & BUMPER 9HA426 Chrome Plated 9HA426SS Cast SS TURN LATCH & COVER 9HACL36N Chrome Plated 9HACL3SS6N Cast SS ACCURATE DOOR KIT NEW STYLE Used January 1 2013 to current. Includes all parts shown and security screws. 9HACL505A Chrome Plated Side view of Hinge 9AA103 A = 1-5/8" HINGE PIN 5/16" Dia. 2-13/16" Long 9AA101 Old Style For Outswing 9HAP23 U TRIM DOOR INSERT 9HAP15 CAM SET (Plastic) 9HAP35 Current CAST STAINLESS STEEL OUTSWING TYPE FOR LAMINATE 9HAP54 1-1/4" POLY 9HAP56 1" PHENOLIC 9HAP58 3/4" Current CAST STAINLESS STEEL INSWING All American Chrome Plated Hardware For Use On Both Metal & Plastic 1/2" Dia. 9AA108 NYLON CAM 9AA107 TYPE FOR LAMINATE 9HAP55 1-1/4" POLY 9HAP57 1" PHENOLIC 9HAP59 3/4" For inswing For 1-1/4" Sq. Edge 9A2353 CHROME 9A2899 1-1/2" W x 3-1/4" L 2-3/4" bet. Screws For use on Plastic Laminate 1-1/2 Bet. Screws 9AA112 9AA115 Brackets on page 66-67 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. Old Style 9HAP27 TOP OR 9HAP10 A = 1-11/16" HINGE PIN 3/8" Dia. 3-7/16" Long 9HAP30 Old Style (Surface) 3-1/2" Bet. Screws 9HAP2O Current 9HAP68 CAST SS 1-1/2" W x 3-1/4" L 2-3/4" hole spacing For Outswing For 1-1/4" Sq. Edge 9A2354 CHROME SLIDE LATCH 9A6983 CAST SS 1-3/4" W x 1-1/2" L hole spacing 9AA113 1" Door Insert 9AA132 1" Door Insert 9AA133 HINGE PIN 3/8" Dia. 3-7/16" Long 9AA111 NEXT DAY DELIVERY AVAILABLE TOILET PARTITION HARDWARE 55

56 Toilet Partition Hardware AMPCO For use on Metal 9C3503 A = 1-7/16" 9C3004 A = 1-7/16" HINGE PIN 3/8" Dia. 3-7/16" Long 9CP450 5/8" Dia. 9C3006 INSWING 9A5580 NEXT DAY DELIVERY AVAILABLE TOP PIN (Metal) 1/4" X 3-1/4" 9C4000 CASTING 9C3513 For 1/4" dia. Pin 9C3610 DOOR INSERT 9CP325 BOTTOM CAM HOUSING 9C0140 For use on Plastic Laminate DOOR ESCUTCHEON For 7/8" Thick Doors 9CP425 9F0214N NYLON CAM 9C3002 NYLON CAM 9CP375 1/2" Dia. 9CP350 OUTSWING 9A5570 INSWING 9A5980 OUTSWING 9A5970 TOILET PARTITION HARDWARE 2-3/4" Bet. Screws 9CP100 Metal Only PIN (Metal) 3/8" Dia. 3-3/4" Long 9AM110 Laminate Only TOP PIN (Metal) 3/8" Dia. 3-5/8" Long 9AM125 DOOR STOP 9A0412 Bobrick Available For use on Metal and Plastic Laminate COAT HOOK & BUMPER INSWING 96200B For Outswing 9AM415 DOOR ESCUTCHEON For 1" Thick Doors 9AM150 COAT HOOK DOUBLE PRONG OUTSWING 3" Projection, 1-3/4" High 9G0161 American Sanitary For use on Metal and Plastic Laminate INSWING COAT HOOK & BUMPER 9AM325 9AM450 DOOR INSERT 9AM240 Top and Bottom hinges are more easily identified by measuring the distance "A" on your hinge and comparing it to "A" next to the part. Screws Are Supplied with All Hardware 9AM280 Chrome 9A3293 Cast SS A = 1-5/8" 5/8" Dia. 9AM270 OUTSWING COAT HOOK DOUBLE PRONG 9AM350 56 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. How to Identify Hardware Side view of Hinge 9AM175 Chrome 9A3793 Cast SS A = 1-5/8" NYLON CAM 9AM220 SLIDE BOLT ASSEMBLY 2-3/4" Bet. Screws 9AM500

Toilet Partition Hardware 57 Comtec / Capital / Hiny Hiders Replacement Hinge inserts USE WITH OUR HINGES ONLY TOP STRIKE/KEEPER INSWING ALUMINUM 6" High 9HSISA STRIKE/KEEPER OUTSWING ALUMINUM 6" High 9HS0SA For 7/16" dia. Pin 9F0211N DOOR ESCUTCHEON For 1" Thick Doors 9F0316 COMTEC OUTSWING FLAT STOP 6" High 9A5898 COMTEC INSWING FLAT STOP 6" High 9A5798 9F0301 Chrome 9A3293 Cast SS A = 1-5/8" BOTTOM REPLACEMENT HINGE INSERTS 9HHGB-TOP 9HHGB- BOTTOM DOOR INSERT For 1" Thick Doors 9F0317 REPLACEMENT INTERGRAL HINGE SET 9A7005 Fiat - Chrome Plated Hardware SLIDE LATCH ALUMINUM 3-1/2" between screws 9HLSLA 9F0300 Chrome 9A3793 Cast SS A = 1-11/16" HINGE SET SET OF 2 HINGES 8" High. Instructions Included 9HHGB SLIDE BOLT ASSEMBLY 2-3/4" Bet. Screws 9/16" Bar to Door Clearance 9F0302 ADA HINGE SET SET OF 3 HINGES 8" High. Instructions Included 9HHGBADA 9F0214N A = 1-11/16" (New) 92500B NEXT DAY DELIVERY AVAILABLE TOP PIN (Metal) 3/8" Dia. 3-7/16" Long 9F0310 TOP PIN (Metal) 7/16" Dia. 3-3/16" Long 9F0207N 9FL100 A = 1-7/16" 9FL400 TOP PIN 3/8" Dia., 3" Long 9FL125 For Outswing 9F0303 9F0227 9FL200 A = 1-7/16" RUBBER ONLY 9F0380 Flush Metal For use on Metal COAT HOOK & BUMPER 9FL450 LATCH KNOB & COVER 9FL325 BOTTOM CAM HOUSING FRONT 9FL275 Unplated 9FL275CH Chrome plated NYLON CAM 9FL225 KNOB & COVER 9FL325A 9F0304 11/16" Dia. 9F0311 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. NYLON CAM 9F0312 INCLUDES PIN When Ordering Specify Pin Type Straight or Offset CASTING For use on metal. 9FL265 Brackets on page 66-67 5/8" Dia. 9FL250 LATCH HOUSING FOR CONCEALED LATCH (Unplated) 9A6606 TOILET PARTITION HARDWARE 57

58 Toilet Partition Hardware FLUSH METAL (Continued) For use on Plastic Laminate 9FL600 Chrome 9A3793 Cast SS A = 1-5/8" 9FL700 Chrome 9A3293 Cast SS A = 1-5/8" DOOR ESCUTCHEON For 7/8" Thick Doors 9FL650 DOOR INSERT 9FL775 TOP PIN (Metal) 3/8" Dia. 3-1/2" Long 9FL625 NEXT DAY DELIVERY AVAILABLE For Outswing 9FL900 91500P Chrome 9A3793 Cast SS A = 1-11/16" 9FL925 91000P Chrome 9A3293 Cast SS A = 1-11/16" GENERAL SLIDE BOLT ASSEMBLY 2-3/4" Bet. Screws 9FL800 For use on Plastic Laminate 2-3/4" Bet. Screws 9/16" Bar to Door Clearance 92000P NYLON CAM 9FL725 920601 15/32" Dia. 9FL750 For OutswingFor 1-1/4" Sq. Post 92060E Older Style For Use on Metal Newer Style TOILET PARTITION HARDWARE 91500B 11/16" Dia. 91006B NYLON CAM 91002B 92060B 91000B A = 1-5/8" LATCH KNOB & COVER (Concealed 2 pin style) 92500A (New) 92500B BOTTOM CAM HOUSING 91005B Unplated 91005BC Chrome Plated INCLUDES PIN When Ordering Specify Pin Type Straight or Offset and Outswing 92560E TOP PIN (Metal) 3/8" Dia. 3-3/4" Long 91504B TOP PIN 3/8" Dia. 3" Long For 91500B & 91500P 91503B 1-1/8" Bet.Screws 96320A A = 1-11/16" 1-1/8" Bet.Screws 96319A A = 1-11/16" BUMPER KEEPER 9K0152 LATCH KNOB 96318A Chrome 9HH101 Cast SS LATCH COVER 96318B Chrome 9HH201 Cast SS BOTTOM CAM & 96319E TOP PIN 1/4" Dia. 2-7/8" Long 96320B CASTING For Metal Doors 9K0245 LATCH KNOB & COVER 92000C LATCH KNOB 92500C w/straight pin 9A8190 w/offset pin LATCH KNOB 96318AA Chrome 9HH111 Cast SS 58 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Toilet Partition Hardware 59 GLOBAL - Chrome Plated Hardware 9G0225 A = 1-7/16" 9G0230 A = 1-7/16" PIN 3/8" Dia. x 3" Long 9G2252 For Outswing 9G015E CASTING 9G0220 BOTTOM CAM HOUSING) 9G0240 unplated 9FL275CH Chrome Plated 9G0151 TOP PIN (Metal) 3/8" Dia. x 3-3/4" Long 9G2253 LATCH KNOB & COVER (Screw Fastened/Concealed) 9G0139S 5/8" 9G0237 For use on Metal NYLON CAM 9G0232 ADA DOOR KIT 9G4000A Chrome Plated (Surface) 3-1/2" Bet. Screws 5/8" Bar to Door Clearance 9G0136 LATCH KNOB & COVER (Screw fastened) 9G0139AS COMPLETE STANDARD DOOR KIT. INCLDS. SAFETY SCREWS 9G4000 Chrome Plated With 3/8" Door to Offset Bar Clearance 9G0137 NEXT DAY DELIVERY AVAILABLE 9G150C LATCH KNOB & COVER 9G0139 - Chrome Plated 9A6148 - Cast SS For use on Plastic Laminate LATCH KNOB & COVER 9G0139A - Chrome Plated 9A6158 - Cast SS TOP OR 9G631A and Outswing 9G631H WRAP AROUND 9HH350 Chrome 9HH360 Cast SS UPPER DOOR CASTING 9HH325 Unplated 9HH326 Cast SS LOWER DOOR CASTING 9HH525 Unplated 9HH526 Cast SS U TRIM DOOR INSERT 9G631B 9HH300 2-3/4" Bet. Screws 9HH125 Chrome 9F0302SS Cast SS 9HH500 HINGE PIN (Metal) 3/8" Dia. x 3-7/16" Long 9G631C CAM SET (Plastic) 9G631E HADRIAN - Chrome Plated Hardware LATCH KNOB 9HH110 Chrome 9HH111 Cast SS NYLON CAM 9HH700 LATCH KNOB 9HH100 Chrome 9HH101 Cast SS WRAP AROUND 9HH550 Chrome 9HH560 Cast SS TOGGLE & SCREW For Hinges 9HH450 LATCH COVER 9HH200 Chrome 9HH201 Cast SS (New) LATCH COVER & KNOB 9G631F INCLUDES PIN When Ordering Specify Pin Type Straight or Offset 9HH800 Chrome 9HH810 Cast SS TOP PIN 9HH400 1/2" Dia. 9HH600 TOILET PARTITION HARDWARE Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 59

60 Toilet Partition Hardware Knickerbocker - Chrome Plated Hardware For use on Metal NEXT DAY DELIVERY AVAILABLE 1-1/8" Bet. Screws 9K0240 A = 1-11/16" BOTTOM CAM HOUSING 9K0340 Not Plated 9K1240 A = 1-11/16" 1-1/8" Bet. Screws For 9KCAMM & 9K0231 9K0230 A = 1-11/16" 9K1230 A = 1-11/16" CASTING For Metal Doors 9K0245 For use on Plastic Laminate DOOR STRIKE & KEEPER 9K0152 BOTTOM CAM & 9K0231N BUMPER KEEPER 9K1152 BOTTOM CAM 9KCAMM TOP PIN (PLASTIC) 1/4" Dia. x 2-3/4" Long 9K241M BOTTOM HOUSING 9K1340 TOP PIN 1/4" Dia. X 2-7/8" Long 9K241P BOTTOM CAM 9KCAMP DOOR LATCH INSIDE MECHANISM KIT 9K0253 For use on Plastic Laminate and Metal LATCH KNOB 9K0250 LATCH COVER 9K0255 LATCH KNOB & COVER 9K0250A 5/8" Dia. 9K0231 TOILET PARTITION HARDWARE 9CP400 A = 1-9/16" For Outswing 9CP200 NYLON CAM 9CP375 1/2" Dia. 9CP350 9CP300 A = 1-9/16" 9CP250 METPAR For use on Plastic Laminate and Metal DOOR ESCUTCHEON For 7/8" Thick Doors 9CP425 2-3/4" Bet. Screws 9CP100 DOOR INSERT 9CP325 TOP PIN (Metal) 3/8" Dia. 3-1/2" Long 9CP450 60 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Toilet Partition Hardware 61 METPAR (Continued) For use on Metal 9C3503 A = 1-7/16" 90C410 90C400 9C3004 A = 1-7/16" LATCH COVER & KNOB 90C300 NYLON CAM 9C3002 BOTTOM CAM HOUSING 9C0140 Unplated 91005 BC Chrome PLated 5/8" Dia. 9C3006 LATCH COVER & KNOB 90C300A CASTING 9C3513 NYLON CAM Pintle Combination 9C0235 NEXT DAY DELIVERY AVAILABLE TOP PIN (Metal) 3/8" Dia. 3-3/4" Long 9C3505 TOP PIN (Metal) 3/8" Dia. 3" Long 9C3504? If in Doubt Please Send a Sample MILLS - Chrome Plated Hardware (Porc.) 90T317 TOP & 1-3/8" Bet. Screws 90T100-110 90T116 SLIDE BOLT/LATCH 2-3/4" Bet. Screws 3/8" Bars to Door Clearance 90T160 Visit Our Website or Call [800] - 642-2403 for Free Color Charts LATCH / KEEPER BUMPER KIT 90T390 N/A COAT HOOK & BUMPER 3-3/8" Projection 2-3/4" High 90T285 BUMPER KEEPER 90T120 SLIDE BOLT/LATCH 90T290 (18 GA.) 1-5/8" Bet. Screws 90T316 TOILET PARTITION HARDWARE Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 61

62 Toilet Partition Hardware Sanymetal Chrome Plated Hardware For use on Metal 1-1/4" Bet. Screws 9S7780 A = 1-9/16" 1-1/4" Bet. Screws 9S7770 A = 1-9/16" OBSOLETE Replaced with 9S7780 OBSOLETE Replaced with 9S7770 NEXT DAY DELIVERY AVAILABLE CASTING For Metal Doors 9S8044 BUMPER For Latch 2" Bet. Screws 9S2400 STOP 9S2704 Keeper Bumper 9S8801 KEEPER For Latch 2" Bet. Screws 9S2401 SLIDE BOLT/LATCH 2-5/8" Bet. Screws 9S7431 Latch Knob OBSOLETE Replace with 9S7361 LATCH KNOB, COVER & PIN KIT 9S8819 Latch Cover OBSOLETE Replace with 9S7360 Latch Pin STAINLESS STEEL LATCH KNOB, WITH SCREW, COVER & PIN: 9S8821 TOILET PARTITION HARDWARE 9S410T THROW LATCH 3-1/2" Bet. Screws 9S7531 BOTTOM POWER BEARING For 9S7360 9S6100 1-1/4" Bet. Screws 9S7361 KEEPER 9S2701 BOTTOM POWER BEARING For 9S5862 & 9S7770 9S7961 POST TOGGLE & SCREW 9S5860 1-1/4" Bet. Screws 9S7360 A = 1-1/2" A = 1-1/2" PLASTIC PIN For 7361, 5861 & 7780 3/8" Dia. 2-1/2" Long 9S7774 For use on Plastic Laminate and Metal COAT HOOK & BUMPER 1-1/8" bet. Screws 9S7810 N/A Latch Knob Latch Cover Latch Pin TOP DOOR HINGE ESCTCHEON 9S6101 LATCH KNOB & COVER 9S8820 Notched Brackets on page 66-67 9S8861 COAT HOOK & BUMPER 7/8" bet. Screws 9S6810B 62 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Common Toilet Partition Hardware 63 SLIDE BOLT ASSEMBLY 2-3/4" Bet. Screws 9/16" Bar to Door Clearance 9F0302 - Chrome 9F0302SS - Cast Stainless Steel ADA* Latches for use with lift type keeprs Fasteners Included Chrome Plated Zamac Unless Indicated 2-3/4" Between Screws 3/8" Bar to Door Clearance 90T160 - Chrome 9A5033 - Cast Stainless Steel 3-1/2" Between Screws 5/8" Bar to Door Clearance 9G0136 - Chrome 9A5053 - Cast Stainless Steel 3-1/2" Between Screws 3/8" Door to offset bar clearance 9G0137 - Chrome 9A5063 - Cast Stainless Steel 9HAP68 CAST SS 1-1/2" W x 3-1/4" L 2-3/4" hole spacing DOOR PULL 3-1/2 " Bet. Screws 9A0540 DOOR PULL 2-3/4" Bet. Centers 9A0620 2-5/8" Bet. Screws 9S7431 1-1/2" W x 3-1/4" L 2-3/4" bet. Screws 9A2899 Chrome Plated THROW LATCH Chrome Plated Brass 3-1/2" Bet. Screws 9S7531 with Indicator for 1`" doors 2-3/4" bet. Screws 9G2000 Cast SS Door Handles Chrome Plated DOOR PULL 4" Bet. Centers 9A0171 DOUBLE DOOR PULL 6" Bet. Centers for 1" doors 9HH001 Chrome Plated DOOR PULL 2-5/8" Bet. Centers 9A7401 ADA* Door Pull ADA DOOR PULL 3" High x 5-1/8" Long 9A6251 9A0625 STAINLESS STEEL 1-7/8" Between Screws 1/8" Bar to Door Clearance 9A7055 * See Stainless Steel section for Keeper/stop INSWING LATCH & STRIKE Stamped Stainless Steel Can be used for outswing if door and post are equal. 9A0104 MATERIAL CHROME PLATED BRASS CAST STAINLESS STEEL SLIDE LATCH 1-3/4" W x 1-1/2" L hole spacing 9A6983 CAST SS HEAVY DUTY THROW LATCH WITH KEEPER Chrome Plated Brass 9S5701 Aluminum 3-1/2" Between Screws 9HLSLA CONCEALED LATCH FIX IT KITS To cover up Concealed Latch Holes DOOR STOP 2" High 9A0412 LATCH & KEEPER Stamped Stainless Steel 9A0106 Coat Hooks and Door Stops COAT HOOK & BUMPER 2-3/4" Projection, 2-1/4" High 9HH900 9HH900SS - Cast SS COAT HOOK & BUMPER 3-1/2" Projection 2-3/4" High 9G0160 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. For Powder Coated Steel & Plastic Laminate Doors For 1" Thick Doors - Round Edge for Powder Coated Steel and for 1" Square edge for Plastic Laminate For 1-1/4" Pilasters All Hardware included - SlideBolt Latch - Inswing or Outswing Hardware(Keeper Bumper) - Stainless Steel "U" Shape cover for both sides of door - All Screws Included Aluminum 3-1/2" Between Screws 9A0102 PLEASE CHECK WITH YOUR LOCAL CODE * TO VERIFY ADA REQUIREMENTS. LATCH WITH KEEPER Indicator an Door Pull 9A6069 COAT HOOK DOUBLE PRONG 3" Projection, 1-3/4" High 9G0161 DOOR STOP PILASTER MOUNTED 2-1/2" High x 4-1/4" Long 9A4151 9A4153 Chrome Plated Zamac 9A1116 9A1117 9A1118 9A1119 Stainless Steel 9A1122 9A1123 9A1120 9A1121 EDGE TYPE & DOOR SWING Round Edge Inswing Round Edge Outswing Square Edge Inswing Square Edge Outswing EDGE TYPE & DOOR SWING Round Edge Inswing Round Edge Outswing Square Edge Inswing Square Edge Outswing COAT HOOK & BUMPER 3" Projection, 2" High 9S7810 COAT HOOK & BUMPER 3-1/8" Projection, 2-1/8" High 96200B MATERIAL POLISHED STAINLESS STEEL CAST STAINLESS STEEL NEXT DAY DELIVERY AVAILABLE TOILET PARTITION HARDWARE 63

64 Common Toilet Partition Hardware Square Edged Wrap Around Hinge Sets Fasteners Included, Chrome Plated Zamac Unless Indicated 7/8" Thick Doors 1-1/4" Thick Pilasters 1" Thick Doors 1" Thick Pilasters 1" Thick Doors 1-1/4" Thick Pilasters Hinge Set NEXT DAY DELIVERY AVAILABLE TOP PART ASSEMBLY 9A3020 Chrome 9A3023 Cast SS BOTTOM PART ASSEMBLY 9A3010 Chrome 9A3013 Cast SS 16 Gauge - 1/8" Pin 54" & 57-1/2" lengths with Spring Close DOOR SWING LENGTH 9A70C1 RH-OUT, LH-IN 57-1/2 9A70C2 LH-OUT, RH-IN 57-1/2 9A70C4 RH-OUT, LH-IN 54 9A70C5 LH-OUT, RH-IN 54 Without Spring Close DOOR SWING LENGTH 9A70C3 ALL 57-1/2 TOP & BOTTOM PART ASSEMBLY 9A3780 Chrome 9A3153 Cast SS TOP PART ASSEMBLY 9A3720 Chrome 9A3043 Cast SS BOTTOM PART ASSEMBLY 9A3710 Chrome 9A3033 Cast SS ADA Continuous Piano and Full Length Surface Mounted Hinges Can be Raised up 3/8" for Emergency Entry Strengthen your Door Provide More Privacy Made of Stamped Stainless Steel 16 Gauge - 1/8" Pin 71-1/2" length with Spring Close DOOR SWING LENGTH 9A7759 RH-IN LH-OUT 71-1/2 9A7769 LH-IN, RH-OUT 71-1/2" 14 Gauge - 1/4" Pin 54-1/2" & 57-1/2" lengths with Cam Close LENGTH 9A7789 57-1/2 9A7599 54-1/2 REPLACEMENT INTERGRAL HINGE SET 9A7005 Vault Hinge VAULT HINGE SET HEAVY DUTY CAST STAINLESS STEEL 9A7813 Use for 3/4" to 1" door 9A7803 Use For 1/2" Door - 1/2" Pilaster 9A7853 Use for 1/2"Door - 3/4" to 1" Pilaster Surface Mounted Hinge Sets (Upper and Lower) TOILET PARTITION HARDWARE 1-1/2" 1-1/2" 1-1/2" 2-7/16" 2-7/16" 2-5/16" Medium Duty ROUND BARREL MATERIAL DOOR SWING CHROME FOR RIGHT HAND 9A70B1 PLATED BRASS OUTSWING OR LEFT HAND INSWING FOR LEFT HAND 9A70B2 OUTSWING OR RIGHT HAND INSWING STAMPED STAINLESS STEEL STAMPED STAINLESS STEEL FOR RIGHT HAND OUTSWING OR LEFT HAND INSWING FOR LEFT HAND OUTSWING OR RIGHT HAND INSWING FOR RIGHT HAND OUTSWING OR LEFT HAND INSWING FOR LEFT HAND OUTSWING OR RIGHT HAND INSWING 9A7043 9A7033 9A7103 9A7093 1-1/2" 1-1/2" DOOR SWING 2-3/8" 2-3/8" Heavy Duty SQUARE BARREL MATERIAL DOOR SWING STAINLESS FOR RIGHT HAND 9A7051 STEEL OUTSWING OR LEFT HAND INSWING FOR LEFT HAND 9A7052 OUTSWING OR RIGHT HAND INSWING ROUND BARREL MATERIAL DOOR SWING CAST FOR RIGHT HAND 9A7SS1 STAINLESS STEEL OUTSWING OR LEFT HAND INSWING FOR LEFT HAND OUTSWING OR RIGHT HAND INSWING 9A7SS2 SUPPLIED WITH FASTENERS FOR 1" DOORS & 1-1/4" POST. OTHERS SCREWS AVAILABLE. 64 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Common Toilet Partition Hardware 65 1-9/16" bet. screws Flat surface type 90T116 Chrome 9A5143 Cast SS KEEPER 1-1/2" bet.screws POST SIZE CHROME PLATED 9A5620 1" 9F0304 1-1/4" CAST STAINLESS STEEL 9A5623 1" 9A5113 1-1/4" STOP ANY THICKNESS POST Inswing use: Keeper - 9S2401J Chrome and Stop: 9S2704 Chrome 9A5173 Cast SS Outswing ONLY use: 9S2704 Chrome CAST STAINLESS STEEL OUTSWING 1-1/4" Post 9G0151 - Chrome Strike and Keepers for Square Edge Posts Fasteners Included, Chrome Plated Zamac Unless Indicated OR Outswing 1-1/2" bet. screws Flat surface type 9A5240 Chrome 9A5243 Cast SS TYPE FOR LAMINATE 9HAP54 1-1/4" POLY 9HAP56 1" PHENOLIC 9HAP58 3/4" CAST STAINLESS STEEL INSWING TYPE FOR LAMINATE 9HAP55 1-1/4" POLY 9HAP57 1" PHENOLIC 9HAP59 3/4" KEEPER For Outswing 1-1/2" bet.screws POST SIZE CHROME PLATED 9A5720 1" 9F0303 1-1/4" CAST STAINLESS STEEL 9A5723 1" 9A5213 1-1/4" For Outswing 1-1/2" bet. screws Flat surface type 9A5260 Chrome 9A5263 Cast SS STOP For Outswing For 1-1/4" Sq. Edge 9A2354 CHROME For 1-1/4" Sq. Edge 9A2353 CHROME ANY THICKNESS POST Inswing use: Keeper - 9S2701 Chrome 9A5183 Cast SS and Stop: 9S2704 Chrome 9A5173 Cast SS Outswing ONLY use: 9S2704 Chrome 1-1/2" bet.screws POST SIZE CHROME PLATED 9A5820 1" 9S410T 1-1/4" CAST STAINLESS STEEL 9A4903 3/4" 9A5823 1" 9A5343 1-1/4" 1-1/2" bet. screws Flat surface type 9A5985 Chrome 9A5283 Cast SS Inswing or Outswing for Concealed Latch 1-1/4" Post 9F0227 Chrome Inswing or Outswing for Concealed Latch 1-1/4" Post 9K1152 Chrome Strike and Keepers for Round Edge Posts For Outswing 1-1/4" Post For Outswing 1-1/4" Post 9G015E - Chrome KEEPER 9A5970 Chrome 9A5973 Cast SS Fasteners Included, Chrome Plated Zamac Unless Indicated 1-1/4" Post 9A5330 - Chrome STOP and Outswing for Concealed Latch POST SIZE CHROME PLATED 9A5730 1" 92560E 1-1/4" CAST STAINLESS STEEL 9A5733 1" 9A5233 1-1/4" ANY THICKNESS POST 1-7/8" Bet. Screws Inswing use: Keeper - 9A7056 and Stop - 9A7057 Outswing ONLY use: 9A7057 1-1/4" Post 9A5980 Chrome 9A5983 Cast SS For Outswing Flat Surface 9A5640 Chrome 9A5643 Cast SS Flat Surface 9A5990 Chrome 9A5653 Cast SS For Outswing 1-1/4" Post 9A5570 - Chrome 9A5573 - Cast SS NEXT DAY DELIVERY AVAILABLE TOILET PARTITION HARDWARE 1-1/4" Post 9A5580 - Chrome 9A5583 - Cast SS or Outswing 1-1/4" Post 7/16" w x 3/4" h slot. 92060B - Chrome 9A5513 - Cast SS or Outswing 1-1/4" Post 1/4" w x 3/4" h slot. 90C410 - Chrome or Outswing 1-1/4" Rnd. Post 9A5590 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 65

66 Common Toilet Partition Hardware "U" BRACKET 1-1/2" high x 1-3/8" Long 9A1914 1" Aluminium Brackets ONE-EAR BRACKET 1-1/2" high x 2-3/4" Long 9A1644 3/4" 9A1764 1" 9A1844 1-1/4" TWO-EAR BRACKET 3" high x 2-3/4" Long 9A2264 1" NEXT DAY DELIVERY AVAILABLE TOILET PARTITION HARDWARE ANGLE BRACKETS 1-3/4" x 1-3/4" 9A0160 TWO-EAR BRACKET 1-1/2" high x 2-3/4" Long 9A1754 1" ALCOVE CLIP 1" Panel to 1-1/4" Pilaster 9A0155 TWO-EAR BRACKET 1-1/2" high x 2-1/2" Long PANEL/PILASTER 9A0162 3/4" 9A0163 7/8" 9A0175 1" 9A0183 1-1/4" TWO-EAR BRACKET 1-1/2" high x 3 1/2" Long 9A1280 1" 9A1330 1-1/4" SINGLE-EAR BRACKET 1-1/2" high x 3 1/2" Long 9A1270 1" 9A1310 1-1/4" Split End ROUND EDGE PILASTER SHOE One End Split for Easy Installation. 1-1/4" x 2", 3", 4", 5", 6", 7", 8", 10", 12", 16", 18", 22" & 24" 9A0308 3" HIGH BRACKETS AVAILABLE URINAL SCREEN BRACKETS 3-1/2" LONG AVAILABLE Panel/Pilaster Brackets (Chrome Plated) ALCOVE CLIP SETS (2 Per Set) Used to join Panel to Pilaster edge to edge. 4 Sets of Two required per Panel. 9A8340 ONE-EAR BRACKET 1-1/2" high x 2-1/2" Long PANEL/PILASTER 9A0164 3/4" 9A0165 7/8" 9A0176 1" 9A0184 1-1/4" Urinal Screen Brackets (Chrome Plated) SCREEN BRACKET LENGTH 9AWB25 1 1/4" 6" 9AWB27 1" 12" FLOOR SHOE For 1-1/4" x 1-1/4" Post 9A1763 "U" BRACKET 3" high x 1-3/8" Long 9A2304 1" SCREEN BRACKET FOR ANY THICKNESS SCREEN 1-1/2" high x 3-1/2" long 9A1320 Split End SQUARE EDGE PILASTER SHOE 1-1/4" x 2", 3", 4", 5", 6", 7" 8", 9", 10", 11", 12" & 14", 16", 18", 20", 22", 24" 9A0306 ALCOVE CLIP For same thickness SS 2-5/8" X 1-1/2" 9A8369 U BRACKET 1-1/2" high x 1-3/8" Long PANEL/PILASTER 9A0189 3/4" 9A0190 7/8" 9A0191 1" 9A0194 1-1/4" FLEXI-MOUNT URINAL SCREEN BRACKET for 1/2" and 1" urinal screens. 1-1/4" high x 3-1/2" long. 9a2001 = 1" thick Pilaster Shoes 3" High (Stainless Steel) FLOOR SHOE For 1-3/4" x 1-3/4" Post 9A0304 END PLUG For 1-1/2" x 1" Rectangular Tubing 9A0666 ONE-EAR BRACKET 3" high x 2-3/4" Long 9A2274 1" 9A2294 1-1/4" Headrail Brackets END PLUG Overall Size 1" X 2" Anti-grip Tubing 9A0667 BRACKET For 1-1/4" Thick Headrail 9A0213 For 1" Thick Headrail 9A0215 Partition Brace "L" TYPE PARTITION BRACE - Stainless Steel, Floor Mounted Unit supports 1/2" to 1-1/2" thick panels. Height is adjustable. 9A6005 - Adjusts 11-1/2" to 14" 9A85183 - Adjusts 9-1/2" to 12" 9A85193 - Adjusts 7-1/2" to 10" "U" TYPE PARTITION BRACE - Stainless Steel, Floor Mounted Unit supports 1/2" to 1-1/4" thick panels. Height is adjustable. 9A8503 - Adjusts 11-1/2" to 14" 9A85083 - Adjusts 9-1/2" to 12" 9A85093 - Adjusts 7-1/2" to 10" ALUMINUM SQUARE POST ONLY For 1-1/4" x 1-1/4" x 10' 9A1762 ALUMINUM SQUARE POST ONLY For 1-3/4" x 1-3/4" x 10' 9A0303 66 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.

Common Toilet Partition Hardware 67 Pilaster Anchoring Device Very Popular NUMBER TO USE PILASTER WIDTH 1 2" 9A07192 1 3, 4, 5, 6" 9A07193 2 7+" 9A07194 FOR 1-1/4" & 1-1/8" THICK AND UP TO 6" WIDE PILASTERS 9A0309 POPULAR FOR 3/4" AND THICKER AND UP TO 6" WIDE PILASTERS 9A1056 PILASTER ANCHOR PACK For Plastic Laminate All Necessary Screws, Nuts and Anchors Included 9A0310 ONE-EAR BRACKET 1-1/2" high x 2-1/2" Long 9A1649 3/4" 9A1659 7/8" 9A1769 1" 9A1849 1-1/4" ONE-EAR BRACKET 1-1/2" high x 2-1/2" Long 9A1643 3/4" 9A1653 7/8" 9A1765 1" 9A1843 1-1/4" Aluminium ALUMINUM "U" BRACKET 1-3/8" Long 1" PANEL/SCREEN HEIGHT 54" 9A2794 57" 9A0191C ALUMINUM ONE-EAR BRACKET 2-3/4" Long 3/4" PANEL/SCREEN 1" PANEL/SCREEN HEIGHT HEIGHT 57" 9A4364 54" 9A2878 57" 9A0176C ALIMINUM TWO-EAR BRACKET 2-1/2" Long 1" PANEL/SCREEN HEIGHT 41" 9A2888 54" 9A2868 57" 9A0175C ALUMINUM "L" BRACKET 2-3/4" Long ANY PARTITION HEIGHT 57" 9A2684 ALUMINUM "H" BRACKET 1" Long 1" PANEL/SCREEN HEIGHT 54" 9A2858 Stamped Stainless Steel Brackets 3" HIGH BRACKETS AVAILABLE URINAL SCREEN BRACKETS 3-1/2" LONG AVAILABLE TWO-EAR BRACKET 1-1/2" high x 2-1/2" Long 9A1629 3/4" 9A1639 7/8" 9A1759 1" 9A1839 1-1/4" Cast Stainless Steel Brackets 1-1/4" PILASTER/SCREEN HEIGHT 57" 9A0184C TWO-EAR BRACKET 1-1/2" high x 2-1/2" Long Full Height Brackets "U" BRACKET 1-1/2" high x 1-1/2" Long 9A1899 3/4" 9A1999 7/8" 9A1919 1" 9A1949 1-1/4" 9A1623 3/4" 9A1633 7/8" 9A1753 1" 9A1833 1-1/4" Stamped Stainless Steel STAINLESS STEEL "U" BRACKET 1-3/8" Long 1" PANEL/SCREEN HEIGHT 54" 9A2799 57" 9A2369 "U" BRACKET 1-1/2" high x 1-3/8" Long STAINLESS STEEL TWO-EAR BRACKET 2-1/2" Long 1" PANEL/SCREEN HEIGHT 41" 9A2609 54" 9A2869 57" 9A2349 ONE-EAR HINGED BRACKET 3" high x 2-1/2" Long 9A1359 1" 9A1369 1-1/4" 9A1893 3/4" 9A1903 7/8" 9A1913 1" STAINLESS STEEL ONE-EAR BRACKET 2-3/4" Long 1" PANEL/SCREEN 1-1/4" PILASTER/SCREEN HEIGHT HEIGHT 54" 9A2879 57" 9A2359 57" 9A2339 STAINLESS STEEL "H" BRACKET 1" Long 1" PANEL/SCREEN HEIGHT 54" 9A2859 NEXT DAY DELIVERY AVAILABLE TOILET PARTITION HARDWARE Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates. 67

68 Common Toilet Partition Hardware Stamped Stainless Steel SAFETY MIRRORS SLIDE LATCH 1-7/8" between screws 1/8" bar to door clearance Works with all stamped stainless steel strike and keepers 9A7055 STRIKE INSWING Strike/Keeper Outswing 1-7/8" between screws Use with 9A6499/9A7056 9A7057 DOOR PULL 5" between screws 9A6419 DOOR HOOK/STOP INSWING 5/8" wide x 2-3/4" projection 9A4009 Cast Stainless Steel KEEPER - INSWING 1-7/8" between screws Use with 9A7057 9A6499 STRIKE/KEEPER INSWING WITH TAB 1-7/8" between screws DOOR SIZE 9A6469 3/4" KEEPER - INSWING 1-7/8" between screws Use with 9A7057 9A7056 STRIKE/KEEPER - OUTSWING 1-7/8" between screws DOOR SIZE 9A6379 3/4" 9A6459 1" DOOR PULL ADA 3" high x 5-1/4" Long 9A0625 DOOR PULL 2-3/4" between screws 9A6203 DOOR HOOK STOP INSWING Mount on door 9A4003 DOOR STOP OUTSWING 9A4123 Dome & Convex Safety Mirrors Circular Convex Acrylic Mirrors See around corners to eliminate dangerous blind hallways and intersections. Heavy duty mounting bracket(s) are included for easy installation in most locations. DIA. AREA LBS. 12" SMALL AREA 3 KM112 INDOOR SPOT APPL. 18" UP TO 15' 5 KM118 26" UP TO 20' 11 KM126 HEAVY DUTY 18" UP TO 15' 5 KM218 OUTDOOR 26" UP TO 20' 14 KM226 30" UP TO 30' 16 KM230 Acrylic 180 0, 360 0 & 90 0 Domes Light weight and virtually unbreakable. SIZE DIA. AREA LBS. Quarter-Dome HALF-DOME 180 0 1/2 18" UP TO 150 SQ FT 4 KM318 1/2 26" UP TO 200 SQ FT 7 KM326 FULL-DOME 360 0 18" UP TO 300 SQ FT 6 KM418 26" UP TO 400 SQ FT 10 KM426 QUARTER DOME 90 0 1/4 18" UP TO 50 SQ FT 3 KM518 1/4 26" UP TO 75 SQ FT 4 KM526 Half-Dome Full-Dome T-Bar Panoramic T-BAR PANORAMIC Designed for use in drop ceilings where the ultimate in visibility is required. No tools required, just remove ceiling tile and drop in the mirror. Great fit and finish T-BAR PANORAMIC 360 PVT-BAR 2x2 24" Dia.-Designed to mount in 2x2 T-Bar Ceiling 13lbs. PVT-BAR 2x4 24" Dia.-Designed to mount in 2x4 T-Bar Ceiling 17lbs. 68 Copyright 2017 Robert Brooke & Associates. This catalog is copyrighted. No portion may be reproduced without the permission of Robert Brooke & Associates.