Technical Manual ReSound Pulse CRT PS60-R & ReSound Pulse CRT LT PSS60-R GN ReSound as Global Technical Operations gto.gnresound.com Lautrupbjerg 9 DK-2750 Ballerup Denmark E-Mail: Service@gnresound.dk
Table of contents Features...3 Part list... 4-6 Final device...7 How to separate the HI...8 Microphone assembly...9 Hybrid connections...10 Coating instructions...11 Colour markers replacement...12 Test equipment... 13-14 Charger spares...15 Page 2 of 15
Description Functional Description The ReSound Pulse CRT (Canal Receiver Technology) is a receiver-in-the-ear model in the existing ReSound Pulse family. All features are identical to the sound tube based ReSound models, except from that the receiver is removed from inside the device housing behind the ear and instead placed at the edge of the tube inside the ear canal. Key features WarpTM high resolution compression New StabilizerTM DFS system SuperTuneTM intelligent rechargeability Directionality Environmental Steering automatic compressor tuning Virtual WindShieldTM wind noise reduction Multi-band noise reduction Low-level expansion Low Battery Warning Indicator Onboard AnalyzerTM DataLogging Standard Configuration Size 312 battery SmartStart power-up timer Battery door with integrated On/Off switch XReceivers w/sound tubes and domes in different sizes 3 standard colours: Medium blonde, marble grey & anthracite Fitting Requirements Aventa fitting software (2.3 or higher) CS63 Flex Strip programming cable HI-PRO, NOAHlink or SpeeLink As from s/n 0700645699 PULSE CRT is delivered with hybrid Coyote 3.1. PULSE LT will continue to have the Coyote 3.0 mounted. For further information please also check GTO Technical News Bulletin No. 2007-08-001 - available on GTOweb Page 3 of 15
Part List Item MICROPHONE,9603 15071600 SUSPENSION,MIC,FRONT 15070700 SUSPENSION,MIC,REAR 15070800 SPRING,BAT,POSITIVE,PLATED 15071101 SPRING,BAT,NEGATIVE,PLATED 15071001 CONTACT,PROGRAMMING MODULE 15070600 FLEX-HYBRID,C3.0,DENMARK 15157500 FLEX-HYBRID,C3.1 FOR PS60-R ONLY 16016900 PIN,LOCK Ø=0.6, L=7.1 15136900 RUBBER GLUE C-296336310 1901-061 GREASE MOLYKOTE FS1292 1908-209 COLOUR MARKER,RED 15075500 COLOUR MARKER,BLUE 15075501 COATING, EGC-1700, 100ML 15290401 WIRE,ESW,RED,7X32U,12MM 15129612 WIRE,ESW,RED,7X32U,8MM 15129608 WIRE,ESW,RED,7X32U,16MM 15129616 WIRE,ESW,GREEN,7X32U,9MM 15129809 WIRE,ESW,GREEN,7X32U,16MM 15129816 Item WIRE,ESW,GREEN,7X32U,11MM 15129811 WIRE,ESW,BLUE,7X32U,9MM 15129909 WIRE,ESW,AMBER,7X32U,9MM 15129709 WIRE,ESW,AMBER,7X32U,12MM 15129712 WIRE,ESW,GREEN,7X32U,12MM 15129812 CERUSTOP FILTER (KIT) 098-0282 PIN REMOVAL TOOL 15492900 CONNECTOR,CRT 004-0073 PROGRAMMING CABLE,RED 15206700 PROGRAMMING CABLE,BLUE 15206701 STRIP CS63/NWT/FLEXSTRIP(10Pk) 50931703 STRIP CS63/NWT/FLEXSTRIP(25PK) 50931704 KIT PROGRAMM. CABLE W/FLEX,RED 15254800 KIT PROGRAMM. CABLE W/FLEX,BLUE 15254801 SIMULATED BATT. PILL,SIZE 312 15854900 TEST FIXTURE 16229100 MEASUREMENT TOOL CRT 004-2013 XREC TEST TUBE 16185100 2CC SNAP-ON ADAPTOR DSA 5000 15238500 Page 4 of 15
Part list Filter, Front FILTER,MIC.FRONT.4PCS.MDM BL 15071202 FILTER,MIC,FRONT,4 PCS,MR GREY 15071204 FILTER,MIC,FRONT,4PCS,ANT 15071208 Filter, Rear FILTER,REAR,312,4PCS,MBL 15798902 FILTER,REAR,312,4PCS,MARBLE GR 15798904 FILTER,REAR,312,4PCS,ANT 15798908 Frame PS60-R FRAME,CRT,PTD,MDM BLONDE 16023402 FRAME,CRT,PTD,ANTHRACITE* 16023408 FramePSS60-R FRAME,CRT,PTD,MDM BLONDE 16125102 FRAME,CRT,PTD,ANTHRACITE* 16125108 *is used for both ANT and MGR HI HI COMPLETE - PS60-R Ver. 3.1 MEDIUM BLONDE 16463302 MARBLE GREY 16463304 ANTHRACITE 16463308 HI COMPLETE - PSS60-R MEDIUM BLONDE 16125202 MARBLE GREY 16125204 ANTHRACITE 16125208 Housing KIT 312 - PS60-R & PSS60-R BLACK 16079101 MEDIUM BLONDE 16079102 METALLIC 16079103 MARBLE GREY 16079104 BLACK METALLIC 16079105 MEDIUM BLONDE METALLIC 16079106 COOL GREY 16079107 ANTHRACITE 16079108 MONZA RED 16079109 PURPLE/GREEN 16079110 PURPLE/BLUE 16079111 GOLDEN/GREEN 16079112 BRONZE/BORDEAUX 16079113 WIMBLEDON GREEN 16079115 STEEL SILVER 16079116 LAVA BLACK 16079117 OCEAN BLUE 16079118 To replace a housing or battery door or to change to another housing colour, a kit consisting of housing and battery door must be ordered Page 5 of 15
Part list Item Ear Box 16069100 Containing: AXLE 0.68X4.8MM 002-0386-1 PIN REMOVAL TOOL 002-0404 MEASUREMENT COUPL. ADAPTOR,CRT 002-0412 UNIVERSAL ADAPTABLE RETENTION 004-0011-001 MEASUREMENT TOOL CRT 004-2013 OPEN DOME,5L 054-0332 OPEN DOME,7L 054-0333 OPEN DOME,10L 054-0334 OPEN DOME,5S 054-0338 OPEN DOME,7S 054-0339 OPEN DOME,10S 054-0340 TULIP DOME,L 054-0390 TULIP DOME,S 054-0391 XRECEIVER STANDARD UNIT XS 0-L 16069200 XRECEIVER STANDARD UNIT XS 1-L 16069300 XRECEIVER STANDARD UNIT XS 2-L 16069400 XRECEIVER STANDARD UNIT XS 3-L 16077100 XRECEIVER STANDARD UNIT XS 0-R 16077200 XRECEIVER STANDARD UNIT XS 1-R 16077300 XRECEIVER STANDARD UNIT XS 2-R 16077400 XRECEIVER STANDARD UNIT XS 3-R 16077500 XREC STD UNIT - PACKED XREC STD UNIT - UNPACKED Page 6 of 15
Final Device XREC to be plugged into the stud of the HI Filter removal tool Cerustop filter kit p/n 098-0282 Wax guard Page 7 of 15
How to separate the HI Remove the filter for back microphone Gently press out the two pins by using the pin removal tool and pull them out by using e.g. tweezers. Take out the battery door and pull out the frame. Filters are recommended to be replaced during any repair situation Pin removal tool p/n 15492900 Page 8 of 15
Microphone Assembly Wire, amber 12 mm p/n 115129712 Wire, green 12 mm p/n 15129812 Front mic suspension Back mic suspension Wire, red 12 mm p/n 15129612 + IN - Use service tool (heat zink) when soldering the microphone wires. Make sure that the suspensions fit well to the sound studs/ports on the microphones. Make sure that wire insulation is undamaged. Brush EGC-1700 coating to the solder points and let dry for 15 sec - then brush once more. Note: Make sure that the microphone is turned right. The wires must be turned towards the back mic suspension as shown on the drawing. Page 9 of 15
Hybrid connections Battery springs Contact module MIC+ MIC IN MIC- Coyote 3.0 - No marking Coyote 3.1 - Black dot marking Contact module H8 H9 Contact module The layout of C3.0 and C3.1 is the same. For visual purpose the C3.1 is marked with black dots. Only PS60-R is mounted with hybrid C3.1. In a repair situation a hybrid C3.0 can be replaced to C3.1. The test system will automatically detect the hybrid version during test. NOTE: Please also see Technical News Bulletin No. 2007-08-001 (available from GTOweb) which is describing the implementation of C3.1. BAT(-) /REC(+) REC(-) BAT(+) Furthermore the improved test fixture is described Page 10 of 15
Coating Cover the pins of the contact module at the solder points and at the in-mould. Press it under the contact pins to ensure good protection. Add molykote in the area indicated by the red dotted lines. Molykote Fill the holes at the battery solder points on both sides with Molykote FC1292 p/n 1908-209. Wipe the surplus Molykote off to prevent soiling of the housing at final assembly. Page 11 of 15
Colour Markers How to place the colour marker: Place the colour marker as long into the hole as possible. Press on the back of the marker with a finger and at the same time turn the pin around until it breaks of. Turn the pin around Pressure here with a finger How to remove the colour marker: Push out the pin a 1/3 of its length using pin tool and turn the device as if it was placed on the ear. The colour marker should then fall out. If the colour marker is not falling out, the battery door can be opened and from the inside the colour marker can be pushed out by using a colour marker remover p/n 15426100. Colour marker, Red p/n 15075500 Blue p/n 15075501 Red p/n 15175600, 25 pcs Blue p/n 15175601, 25 pcs The pin is pushed out Push the colour marker from inside Page 12 of 15
Test equipment Blue dot Programming cable CS63 blue, Left p/n 15206701. Battery pill must be used: Size 312 p/n 15854900 Red dot Programming cable CS63 red, Right p/n 15206700. Kit with programming cable, flex strip and clothes-clip: - Red p/n 15254800 - Blue p/n 15254801 - Flex strip 3 pin (10 pcs) p/n 50931703 - Flex strip 3 pin (25 pcs) p/n 50931704 Page 13 of 15
Test equipment Snap-on adaptor p/n 15238500. To be used with Otometrics 2cc coupler. Use XRec test tube p/n 16185100 when testing Place the Xrec tube into the test fixture. Mount the snap on adaptor on the coupler and place the XRec into it. Connect the hearing instrument to the other end of the Xrec tube The test fixture must be adjusted before use. Loose the two screws. The smallest part must be positioned so that the test tube is in the center of the green circle. Fasten the screws. This adjustmest must also be done on a frequently basis to ensure optimal testing. Insert battery pill and flex strip into the HI Test fixture p/n 16229100 Page 14 of 15
Charger spares Complete package Part no. RESOUND PULSE SUPERTUNE, EU* 15871100 RESOUND PULSE SUPERTUNE, UK* 15870900 RESOUND PULSE SUPERTUNE, US* 15871000 RESOUND PULSE SUPERTUNE, AUS* 15870100 * including all spares Spares Part no. Keyring holder 15734700 Link for keyring holder 15806700 Silicone block 10A 15734300 Silicone block 312 15837300 Battery slide 10A 15837100 Battery slide 312 15837200 Power supply EU 15836800 Power supply UK 15837900 Power supply US 15837500 Power supply AUS 15837700 Page 15 of 15