EMIP60 ISO. EM Series, Inch Pounds - 60 Hz EM (iso) Spec Guides Drawings Spec Sheets Extended Range Ratings Low Temp Heating.

EMIP60 ISO EM Series, Inch Pounds 60 Hz EM007360 (iso) Spec Guides Drawings Spec Sheets Extended Range Ratings Low Temp Heating Rev 1003 Revisions: 81402 Changed EM170/240HZ dwg 31103 Changed HZ dwg to field convertible 50203 EM360 coil area to 27.00 ft sq 51203 Guide Specification updated 70103 Removed EM051 and EM061 9403 Reinstated EM051 and EM061 91103 Updated HZ drawing 92203 EM012 WL COP changed 102103 Corrected EM144360 filter rack dimensions

GUIDE SPECIFICATIONS EM Series 1/26 Ton GENERAL Units shall be performance certified to ISO standard 132561 for Water Loop Heat Pump, Ground Water Heat Pump and Ground Loop Heat Pump applications. Units intended for use on ground loop applications shall have an optional extended range package installed. Units shall be Underwriter Laboratories (UL and cul) listed for safety on all models. Each unit shall be run tested at the factory. Each unit shall be pallet mounted and stretch wrapped. The units shall be warranted by the manufacturer against defects in materials and workmanship for a period of one year on all parts, and 5 years on the compressor. The units shall be designed to operate with entering fluid temperatures between 50 O F (10 O C) and 100 O F (38 O C) in cooling and between 50 O F (10 O C) and F (27 O C) in heating. With the optional factory installed extended range package units shall operate with entering fluid temperatures between 50 0 F (10 O C) and 110 O F (43.3 O C) in cooling and between 25 O F (3.9 O C) and F (27 O C) in heating. CASING & CABINET The cabinet shall be fabricated from heavygauge steel finished with Galvalume plus, an aluminumzinc alloy with a clear acrylic coating for additional corrosion protection. The interior shall be insulated with ½ (12.7mm) thick, multi density, coated, glass fiber. All units shall allow sufficient service access to replace the compressor without unit removal. One blower and two compressor compartment access panels shall be removable with supply and return ductwork in place. A duct collar shall be provided on the supply air opening. A 2" (50.8mm) return air filter rack/duct collar with 1" (25.4mm) thick filters shall be provided with each unit. The units shall have an insulated divider panel between the air handling section and the compressor section to minimize the transmission of compressor noise, and to permit service testing without air bypass. Units shall have a stainless steel condensate drain pan. REFRIGERATION CIRCUITS All units shall contain a sealed refrigerant circuit including a hermetic compressor, capillary tube metering device with strainer or balance port expansion valve, finned tube airtorefrigerant heat exchanger, refrigerant reversing valve and service ports. Compressor shall be high efficiency, designed for heat pump duty, internally spring isolated (if reciprocating type) for maximum sound attenuation and mounted on rubber vibration isolators. Compressor motors shall be equipped with overload protection. Refrigerant reversing valves shall be pilot operated sliding piston type with replaceable encapsulated magnetic coils energized only during the cooling cycle. The finned tube coil shall be constructed of lanced aluminum fins not exceeding fourteen fins per inch bonded to rifled copper tubes in a staggered pattern not less than three rows deep and have a 450 PSIG (3100 kpa) working pressure. Coils shall be epoxy coated using an electro coating process for protection against most airbourn chemicals.the coil shall have aluminum end sheets. The coaxial watertorefrigerant heat exchanger shall be constructed of a convoluted copper (optional cupronickel) inner tube and steel outer tube with a designed refrigerant working pressure of 450 PSIG (3100 kpa) and designed water side working pressure of no less than 400 PSIG (2750 kpa). EXTENDED RANGE PACKAGE An optional extended range package shall include a biflow balanced port expansion valve metering device in place of capillary tubes and insulated water to refrigerant heat exchanger. FAN MOTOR & ASSEMBLY The fan shall be direct drive centrifugal forward curved type with a dynamically balanced wheel. The housing and wheel shall be designed for quiet low velocity operation. The fan housing shall be removable from the unit without disconnecting the supply air ductwork for servicing of the fan motor. The fan motor shall be three speed PSC type for direct drive units and single speed for belt drive units. The motor shall be permanently lubricated and have thermal overload protection. ELECTRICAL Controls and safety devices will be factory wired and mounted within the unit. Controls shall include fan relay, compressor contactor, 24V transformer, reversing valve coil and solid state lockout controller (UPM) The UPM controller shall include the following features: Antishort cycle time delay, random start, brown out/surge/power interruption protection, 90 second low pressure switch bypass timer, shutdown on high or low refrigerant pressure safety switch inputs, shutdown for the optional freezestat or high level condensate sensors, 24 VAC alarm output for remote fault indication, unit reset at thermostat or disconnect, ability to defeat time delays for servicing and automatic intelligent reset. The UPM shall automatically reset after a safety shut down and restart the unit, if the cause of the shut down no longer exists, after the antishort cycle and random start timers expire. Should a fault reoccur within 10 minutes after reset, then a permanent lockout will occur. A light emitting diode (LED) shall annunciate the following alarms: high refrigerant pressure, low refrigerant pressure, low water temperature and a high level of condensate in the drain pan (when equipped with the optional low water temperature and high level condensate sensors). The LED will display each fault condition as soon as the fault occurs. If a permanent lockout occurs, then the fault LED will display the type of fault until the unit is reset. Safety devices include a low pressure cutout set a 20 PSIG (140 kpa) for loss of charge protection (freezestat and/or high discharge gas temperature sensor is not acceptable) and a high pressure cutout control set at 380 PSIG (2600 kpa). An optional energy management relay that allows unit control by an external source shall be factory installed. A terminal block with screw terminals shall be provided for control wiring. PIPING Supply, return water and condensate drain connections shall be brass female pipe thread fittings and mounted flush to cabinet exterior with optional stainless steel, Braided hose kit with swivel connectors. EMSPECS.P65 REV: 903

GUIDE SPECIFICATIONS EM Series 630 Large Commercial GENERAL Units shall be performance certified to ISO standard 132561 for Water Loop Heat Pump, Ground Water Heat Pump and Ground Loop Heat Pump applications for units up to 10 tons. Units intended for use on ground loop applications shall have an optional extended range package installed which consists of an insulated water to refrigerant heat exchanger. Units shall be Underwriter Laboratories (UL and cul) listed for safety on all models. Each unit shall be run tested at the factory. Each unit shall be pallet mounted and stretch wrapped. The units shall be warranted by the manufacturer against defects in materials and workmanship for a period of one year on all parts, and 5 years on the compressor. The units shall be designed to operate with entering fluid temperatures between 50 o F (10 o C) and 100 o F (38 o C) in cooling and between 50 o F (10 o C) and 80 o F (27 o C) in heating. With the optional factory installed extended range package units shall operate with entering fluid temperatures between 50 o F (10 o C) and 110 o F (43.3 o C) in cooling and between 25 o F (3.9 o C) and 80 o F (27 o C) in heating. CASING & CABINET The cabinet shall be fabricated from heavygauge galvanized steel. The interior shall be insulated with ½ (12.7mm) thick, multi density, coated, glass fiber. All units shall allow sufficient service access to replace the compressors without unit removal. Two blower and two compressor compartment access panels shall be removable with supply and return ductwork in place. A duct collar shall be provided on the supply air opening of all vertical units. A 2" (50.8mm) return air filter rack/duct collar with 1" (25.4mm) thick filters shall be provided with each unit. Vertical units shall have an insulated divider panel between the air handling section and the compressor section to minimize the transmission of compressor noise, and to permit operational service testing without air bypass. Units shall have stainless steel condensate drain pan(s). REFRIGERATION CIRCUITS All units shall contain sealed refrigerant circuits including hermetic compressors, thermal expansion valve metering devices, finned tube airtorefrigerant heat exchangers, refrigerant reversing valves and service ports. Compressors shall be high efficiency, designed for heat pump duty, internally spring isolated (except for scroll type compressors) for maximum sound attenuation and mounted on rubber vibration isolators. Compressor motors shall be equipped with overload protection. Refrigerant reversing valves shall be pilot operated sliding piston type with replaceable encapsulated magnetic coils energized only during the cooling cycle. The finned tube coil shall be constructed of lanced aluminum fins not exceeding fourteen fins per inch bonded to rifled copper tubes in a staggered pattern not less than three rows deep and have a 450 PSIG (3100 kpa) working pressure. Coils shall be epoxy coated using an electro coating process for protection against most airbourn chemicals.coils shall have aluminum end sheets. The coaxial watertorefrigerant heat exchangers shall be constructed of a convoluted copper (optional cupronickel) inner tube and steel outer tube with a designed refrigerant working pressure of 450 PSIG (3100 kpa) and a designed water side working pressure of no less than 400 PSIG (2750 kpa). FAN MOTOR & ASSEMBLY(S) The fan(s) shall be belt driven DWDI forward curved type with dynamically balanced wheel(s). The housing(s) and wheel(s) shall be designed for quiet low velocity operation. The fan housing(s) shall be removable from the unit without disconnecting the supply air ductwork for servicing of the fan motor(s). The fan motor(s) shall be 1725 or 3450 RPM 56 frame sealed ball bearing type. The motor(s) shall be permanently lubricated and have thermal overload protection. ELECTRICAL Controls and safety devices will be factory wired and mounted within the unit. Controls shall include fan relay(s), compressor contactors, 24V transformer, reversing valve coils and a solid state lockout control circuit (UPM). The UPM controller shall include the following features: Antishort cycle time delay, random start, interstage delay, brown out/surge/power interruption protection, 90 second low pressure switch bypass timer, shutdown on high or low refrigerant pressure safety switch inputs, shutdown for the optional freezestat or high level condensate sensors, 24 VAC alarm output for remote fault indication, unit reset at thermostat or disconnect, ability to defeat time delays for servicing, time delay between stages and automatic intelligent reset. The UPM shall automatically reset after a safety shut down and restart the unit, if the cause of the shut down no longer exists, after the antishort cycle and random start timers expire. Should a fault reoccur within 10 minutes after reset, then a permanent lockout will occur. A light emitting diode (LED) shall annunciate the following alarms for each refrigerant circuit: high refrigerant pressure, low refrigerant pressure, low water temperature and a high level of condensate in the drain pan (when equipped with the optional low water temperature and high level condensate sensors). The LED will display each fault condition as soon as the fault occurs. If a permanent lockout occurs, then the fault LED will display the type of fault until the unit is reset. Safety devices include a low pressure cutout set at 20 PSIG (140 kpa) for loss of charge protection (a freezestat used for loss of charge protection is not acceptable) and a high pressure cutout control set at 380 PSIG (2600 kpa). An optional energy management relay to allow unit control by an external source shall be factory installed. PIPING Supply, return water and condensate drain connections shall be copper or brass female pipe thread fittings and mounted flush to cabinet exterior. LEMSPECS.P65 Rev: 903

FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com EM Series Ver ertical Dimensions A B C D E F G H J K M N P Q Condenser Recommended MODEL R/A Duct R/A Duct Filter Rack Water Replacement Width Depth Height Flg Width Flg Height Height Connections Nominal Filter Size EM007, 009 19.00 19.00 24.25 11.75 7.75 3.50 8.25 2.38 4.88 7.38 15.00 8.00 10.00 8.25 3/4" F.P.T. 10 X 16 X 1 EM012 19.00 19.00 24.25 11.75 7.75 3.50 9.75 2.38 4.88 7.38 15.00 8.00 10.00 5.00 3/4" F.P.T. 10 X 16 X 1 EM015 21.50 21.50 32.25 11.75 9.75 5.88 7.88 2.38 7.38 13.25 17.50 14.00 16.00 7.88 3/4" F.P.T. 16 X 20 X 1 EM018 21.50 21.50 32.25 13.75 11.75 2.75 6.75 2.38 7.38 13.25 17.50 14.00 16.00 6.75 3/4" F.P.T. 16 X 20 X 1 EM024 21.50 21.50 36.25 13.75 11.75 2.75 6.75 2.38 7.38 12.50 17.50 16.00 18.00 6.75 3/4" F.P.T. 18 X 20 X 1 EM028 21.50 21.50 39.25 15.75 13.75 2.75 5.75 2.38 7.38 12.50 17.50 18.00 20.00 5.75 3/4" F.P.T. 20 X 20 X 1 EM031 21.50 21.50 39.25 15.75 13.75 2.75 5.75 2.38 7.38 13.50 17.50 18.00 20.00 5.75 3/4" F.P.T. 20 X 20 X 1 EM036 21.50 26.00 43.25 15.75 15.75 4.75 5.50 2.38 8.38 14.75 22.00 22.00 24.00 5.50 3/4" F.P.T. 24 X 24 X 1 EM041 21.50 21.50 39.25 15.75 13.75 3.00 5.50 2.38 8.38 14.75 17.50 18.00 20.00 5.50 3/4" F.P.T. 20 X 20 X 1 EM042 21.50 26.00 43.25 15.75 15.75 4.75 5.50 2.38 8.38 14.75 22.00 22.00 24.00 5.50 3/4" F.P.T. 24 X 24 X 1 EM048 24.00 32.50 45.25 15.75 15.75 10.75 6.50 2.63 8.38 14.75 28.00 22.00 24.00 6.50 1" F.P.T. 24 X 30 X 1 EM051 26.00 26.00 43.25 15.75 15.75 5.13 5.13 2.38 6.25 9.75 22.00 28.00 30.00 5.13 1" F.P.T. 24 X 30 X 1 EM060 24.00 32.50 45.25 17.75 17.75 10.00 5.13 3.00 9.63 16.63 28.00 22.00 24.00 5.13 1" F.P.T. 24 X 30 X 1 EM061 26.00 26.00 43.25 17.75 17.75 4.13 4.13 2.38 6.25 9.75 22.00 28.00 30.00 5.13 1" F.P.T. 24 X 30 X 1 EM070 26.00 33.25 58.25 17.75 17.75 9.50 6.50 3.38 8.38 17.38 28.00 30.00 32.00 6.50 1" F.P.T. 16 X 30 X 1 (2) Left Hand Return (FLT) EMVTGDIP FLA.P65 REV: 0903 Right Hand Return (FRT) NOTES: All dimensions within +/ 0.125". All condensate drain connections are 3/4" FPT. EM051 and 061 only available in vertical configuration. Specifications subject to change without notice.

FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com EM Series Horizontal Dimensions A B C D E F G H J K M N P Q R T Condenser Recommended MODEL R/A Duct Filter Rack R/A Duct Water Replacement Width Depth Height Flg Width Height Flg Height Connections Nom. Filter Size EM007, 009 19.00 31.00 11.25 2.00 15.00 14.00 2.38 7.38 2.25 11.75 1.25 7.75 2.25 1.88 10.00 8.00 3/4" F.P.T. 10 X 16 X 1 EM012 19.00 31.00 11.25 2.00 15.00 14.00 2.38 7.38 2.50 11.75 1.25 7.75 2.25 1.88 10.00 8.00 3/4" F.P.T. 10 X 16 X 1 EM015 21.50 43.00 17.00 2.00 17.50 23.50 2.38 13.25 4.00 11.75 1.25 9.75 2.25 1.88 16.00 14.00 3/4" F.P.T. 16 X 20 X 1 EM018 21.50 43.00 17.00 2.00 17.50 23.50 2.38 13.25 3.50 11.75 1.25 13.75 3.50 1.75 16.00 14.00 3/4" F.P.T. 16 X 20 X 1 EM024 21.50 43.00 19.00 2.00 17.50 23.50 2.38 12.50 3.25 11.75 3.25 13.75 3.25 1.75 18.00 16.00 3/4" F.P.T. 18 X 20 X 1 EM028 22.00 45.00 19.00 2.00 19.50 23.50 2.38 12.50 2.50 13.75 1.50 15.75 2.50 1.50 18.00 16.00 3/4" F.P.T. 18 X 20 X 1 EM031 22.00 45.00 19.00 2.00 19.50 23.50 2.38 13.50 2.50 13.75 1.50 15.75 2.50 1.50 18.00 16.00 3/4" F.P.T. 18 X 20 X 1 EM036 22.00 50 19.00 2.00 29.00 23.50 2.38 14.75 2.50 13.75 1.50 15.75 2.50 1.50 18.00 16.00 3/4" F.P.T. 18 X 30 X 1 EM041 21.50 43.00 22.00 2.00 17.50 23.50 2.38 14.75 2.50 13.75 3.00 15.75 3.25 3.00 20.00 18.00 3/4" F.P.T. 20 X 20 X 1 EM042 22.00 50 19.00 2.00 29.00 23.50 2.38 14.75 2.50 13.75 1.50 15.75 2.50 1.50 18.00 16.00 3/4" F.P.T. 18 X 30 X 1 EM048 36.00 43.00 21.00 2.25 33.75 7.00 2.63 14.75 10.13 15.75 2.50 15.75 3.00 2.50 20.00 18.00 1" F.P.T. 18 X 20 X 1 (2) EM060 36.00 43.00 21.00 2.25 33.75 7.00 3.00 16.63 10.13 15.75 1.50 17.75 3.25 1.50 20.00 18.00 1" F.P.T. 18 X 20 X 1 (2) EM070 26.00 78.00 21.50 2.50 44.00 31.50 3.12 18.50 2.75 17.75 2.75 17.75 2.75 1.25 20.50 18.50 1" F.P.T. 20 X 24 X 1 (2) Left Hand Return (Note: Models EM048 & 060 Left Hand Return units have condenser water connections on the front right and electrical knockouts on the front left.) Left Hand Return End Blow (FLE) Left Hand Return Straight Through (FLS) Right Hand Return Right Hand Return Straight Through (FRS) EMHZDGIP.P65 c FHP Manufacturing Company REV:91103 Right Hand Return End Blow (FRE) NOTES: All dimensions within +/ 0.125". All condensate drain connections are 3/4" FPT. Specifications subject to change without notice. EM015070 can be field converted between end blow and straight through supply air configurations

FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com EM Series Counterflow Dimensions A B C D E F G H J K M N P Condenser Recommended MODEL R/A Duct R/A Duct Filter Rack Water Replacement Width Depth Height Opening Opening Flg Width Flg Height Height Connections Nominal Filter Size EM007, 009 19.00 19.00 24.25 6.25 4.25 6.00 10.25 5.00 10.00 10.25 15.00 8.00 10.00 3/4" F.P.T. 10 X 16 X 1 EM012 19.00 19.00 24.25 5.25 4.00 7.00 12.38 5.00 10.00 7.75 15.00 8.00 10.00 3/4" F.P.T. 10 X 16 X 1 EM015 21.50 21.50 32.25 6.25 4.25 6.50 12.00 5.88 16.75 12.00 17.50 14.00 16.00 3/4" F.P.T. 16 X 20 X 1 EM018 21.50 21.50 32.25 9.63 9.25 8.13 8.00 5.88 16.75 8.00 17.50 14.00 16.00 3/4" F.P.T. 16 X 20 X 1 EM024 21.50 21.50 36.25 9.63 9.25 8.13 8.00 5.88 16.00 8.00 17.50 16.00 18.00 3/4" F.P.T. 18 X 20 X 1 EM028 21.50 21.50 39.25 9.63 9.25 8.13 8.00 5.88 16.00 8.00 17.50 18.00 20.00 3/4" F.P.T. 20 X 20 X 1 EM031 21.50 21.50 39.25 9.63 9.25 8.13 8.00 4.88 16.00 8.00 17.50 18.00 20.00 3/4" F.P.T. 20 X 20 X 1 EM036 21.50 26.00 43.25 10.25 9.25 10.00 8.75 4.38 16.75 8.75 22.00 22.00 24.00 3/4" F.P.T. 24 X 24 X 1 EM041 21.50 21.50 39.25 10.25 9.25 7.25 7.75 4.38 16.75 7.75 17.50 18.00 20.00 3/4" F.P.T. 20 X 20 X 1 EM042 21.50 26.00 43.25 10.25 9.25 10.00 8.75 4.38 16.75 8.75 22.00 22.00 24.00 3/4" F.P.T. 24 X 24 X 1 EM048 24.00 32.50 45.25 11.75 10.75 9.25 9.00 6.00 18.25 9.00 28.00 22.00 24.00 1" F.P.T. 24 X 30 X 1 EM060 24.00 32.50 45.25 12.50 12.00 9.00 8.00 4.25 17.75 8.00 28.00 22.00 24.00 1" F.P.T. 24 X 30 X 1 EM070 26.00 33.25 58.25 12.00 12.50 10.63 5.00 3.00 18.50 5.00 28.00 30.00 32.00 1" F.P.T. 16 X 30 X 1 (2) Left Hand Return (FLB) Right Hand Return (FRB) EMCFDGIP.P65 REV: 62899 NOTES: All dimensions within +/ 0.125". All condensate drain connections are 3/4" FPT. Specifications subject to change without notice.

Dimensions All Dimensions +/ 0.125" FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com EM072180 Ver ertical Dimensions Single Large Commercial Units Optional Orientation (979032) Front Return Standard Orientation Dimension Model 072 096 120 150 180 Height 62.00 62.00 62.00 66.50 86.50 Width 42.00 42.00 42.00 42.00 42.00 Depth 32.00 32.00 32.00 32.00 32.00 Condenser Connections A 14.75 14.75 15.00 15.00 15.00 B 8.50 8.50 9.00 9.00 9.00 C 2.75 2.75 3.00 3.00 3.00 Dia. (FPT) 1.00" 1.00" 1.50" 2.00" 2.00" Return Air Opening D(Duct Flange) 38.00 38.00 38.00 38.00 58.00 E(Filter Rack) 40.00 40.00 40.00 40.00 60.00 Replacement Filter Size 072 through 150 20 x 341/2 x 1 (2 per unit) 180 30 x 341/2 x 1 (2 per unit) Top Supply (FFT) Rear Supply (FFR) Rear Return Standard Orientation Optional Orientation (979032) Service Access Panel # Access To: 1 Controls, Compressors, Refrigeration Components 2 & Motor 3 Top Supply (FBT) Front Supply (FBF) Notes: Condensate connections are 0.75" FPT on 072 through 120 and 1.25" FPT on 150 and 180. Due to continuing research and development, specifications are subject to change without notice. EMSVDGIP.P65 Rev. 20501

FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com Dimensions All Dimensions +/ 0.125" Dimension Model 072 096 120 140 Height 21.50 21.50 21.50 25.50 Width 38.00 38.00 38.00 42.00 Depth 78.00 78.00 78.00 82.00 Return Air Dimensions A 2.00 2.00 2.00 2.00 B 20.50 20.50 20.50 24.00 C 18.50 18.50 18.50 22.00 Condenser Connections E 26.25 26.25 27.50 22.50 F 2.75 2.75 3.38 2.75 G 37.50 37.50 38.25 30.75 H 10 19.25 16.75 18.25 Diameter 1"FPT 1"FPT 1.25"FPT 1.50"FPT Supply Air Dimensions ( Outlet) J 15.50 15.50 12.50 18.50 K 13.50 13.50 13.50 16.00 L 10.50 10.50 5.25 14.00 Replacement Filter Size 072120 20 x 341/2 x 1 (2 per unit) 140 24 x 34 x 1 (2 per unit) Service Access Panel# Access To: 1 Controls, Compressors 2 & Motor 3 Compressors, Refrigeration Components EM072140 Horizontal Dimensions 072, 096 & 140 (SLS Only) 120 (SLS Only) Notes: All condensate connections are 0.75" FPT. Due to continuing research and development, specifications are subject to change without notice. EMLHDGIP.P65 Rev. 401

FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com EM170240 Horizontal Dimensions EM170 SLS CONFIGURATION ONLY Dimensions Condenser Connections EM170 1.50"FPT EM240 2.00"FPT Notes: All dimensions +/ 0.125". All condensate connections are 1.25" FPT. EM240 SLS CONFIGURATION ONLY Replacement Filter Size EM170 24 x 34 x 1 (2) EM240 20 x 341/2 x 1 (4) Service Access Panel# Access To: 1 Controls, Compressors, Refrigeration Components 2 s & Motors 3 Compressors, Refrigeration Components Due to continuing research and development, specifications are subject to change without notice. EM170240HZIP.P65 Rev.802

FHP Manufacturing Co. Phone: (954) 7765471 Fax: (800) 7765529 http://www.fhpmfg.com EM144360 Ver ertical Dimensions Dual Large Commercial Units Dimensions All Dimensions +/ 0.125" Model Height A B C D E Front Return Top Supply (FFT) Optional Orientation (979033) Standard Orientation 144 62.00 17.00 10.50 3.00 40.00 38.00 168 62.00 17.00 10.50 3.00 40.00 38.00 210 62.00 14.75 8.50 2.75 40.00 38.00 240 66.50 14.75 8.75 2.75 40.00 38.00 300 66.50 14.75 8.75 2.75 40.00 38.00 360 86.50 15.00 9.00 3.50 60.00 58.00 Model Condenser Condensate Connection Drain Diameter Diameter 144 1.50"FPT 1.25"FPT 168 1.50"FPT 1.25"FPT 210 2.00"FPT 1.25"FPT 240 2.00"FPT 1.25"FPT 300 2.00"FPT 1.25"FPT 360 2.00"FPT 1.25"FPT Rear Return Front Supply (FBF) Standard Orientation Optional Orientation (979033) Front Return Rear Supply (FFR) Recommended Replacement Filter Size (Nominal) 20 x 341/2 x 1 (4 per unit, 144300) 30 x 341/2 x 1 (4 per unit, 360) Service Access Panel # Access To: 1 Controls, Compressors, Refrigeration Components 2 & Motor 3 Rear Return Top Supply (FBT) Due to continuing research and development, specifications are subject to change with out notice. EMDVDGIP.P65 Rev: 102103

Compressor Min. Max. 115160 0 6.6 29.8 2.20 0.10 10.5 15 208/230160 1 3.1 15.9 0.96 0.10 4.8 15 265160 2 2.9 12.3 0.85 0.10 15 Speed High 0.10 410 0.20 380 0.30 350 0.40 315 0.50 280 0.60 210 0.70 0.80 0.90 1.00 1.10 1.20 Medium 390 360 330 300 260 Low 370 340 295 250 All performance at 300 CFM and 1.9 GPM PACKAGE UNITS EM007 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 300 CFM and 2.0 GPM 7300 12.3 10000 4.7 8500 17.3 7500 3.8 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 0.90 3 3/8 12 Size Net Ship 4x6 119 128 ENERGYMISER 0.9 0.7 1.2 1.2 1.4 1.8 1.6 2.5 1.9 3.7 2.1 4.7 Water Capacity Absorb. COP 50 O 8309 445 9828 6323 7586 8309 18.7 8427 6491 567 4.4 8711 455 10264 5915 7509 8328 19.1 7993 6021 578 4.1 9121 9537 465 475 10708 11158 5445 4540 7114 6276 8209 8164 19.6 20.1 7483 9484 5470 7438 590 600 3.7 4.6 9961 7869 8250 485 485 496 11616 9525 9943 5988 5602 5349 7184 7112 7331 7869 7887 20.5 16.2 16.6 8996 8422 10543 6911 6294 8383 611 624 633 4.3 4.0 4.9 67 O 8638 9032 9433 507 518 529 10368 10799 11238 5157 4299 6738 5943 5066 7774 7732 6943 17.0 17.4 17.8 10000 9362 11546 7799 7115 9263 645 658 669 4.2 5.1 7442 7803 525 536 9232 9633 5664 5298 6795 6726 7442 7460 14.2 14.6 10952 10253 8625 7878 682 696 4.7 4.3 67 O 8170 548 10040 4877 6373 7353 14.9 8543 560 10453 4066 5621 7313 15.3 Units are complete packages containing refrigeration 8922 572 10872 4791 6567 15.6 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 6832 584 8825 5199 6238 6832 11.7 safety controls: Overload protection for motors, high and low 7163 597 9200 4864 6175 6848 12.0 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 7500 610 9581 4478 5850 6750 12.3 Extended range option includes expansion valve metering 7842 623 9968 3733 5160 6713 12.6 device, insulated water coil and solid state lockout controls. 8190 636 10361 4398 6028 12.9 6244 646 8449 4751 5700 6244 9.7 6546 661 8800 4445 5643 6258 9.9 100 O 67 O 6854 675 9157 4092 5346 6169 10.2 Phone: (954) 7765471 7167 690 9520 3411 4716 6135 10.4 Fax: (800) 7765529 7485 704 9887 4019 5509 10.6 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM007IP6ISO.P65 Rev:11399

Compressor Min. Max. 115160 0 8.3 40.0 2.20 0.10 12.6 20 208/230160 1 4.0 20.0 0.96 0.10 6.0 15 265160 2 3.3 16.0 0.85 0.10 5.0 15 Speed High 410 380 350 315 280 210 Medium 390 360 330 300 260 Low 370 340 295 250 All performance at 350 CFM and 2.4 GPM PACKAGE UNITS EM009 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 350 CFM and 3.0 GPM 9800 12.0 13000 4.6 11400 17.2 9800 3.7 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 0.90 3 3/8 12 Size Net Ship 4x6 120 129 ENERGYMISER 1.2 1.2 1.5 2.1 1.8 3.3 2.1 4.7 2.4 6.8 2.7 8.4 Water Capacity Absorb. COP 50 O 10525 552 12410 8009 9609 10525 19.1 10955 8440 737 4.4 11035 565 12962 7493 9512 10550 19.5 10391 7829 751 4.1 11554 12081 577 589 13523 14092 6898 5751 9012 7950 10399 10342 20.0 20.5 9728 12331 7112 9672 767 779 3.7 4.6 12617 9967 10451 602 602 616 14671 12022 12551 7585 7096 6776 9100 9008 9286 9967 9991 21.0 16.6 17.0 11696 10950 13706 8987 8184 10899 794 811 822 4.3 4.0 4.9 67 O 10942 11441 11949 629 643 656 13088 13634 14188 6532 5446 8535 7529 6417 9848 9794 8795 17.4 17.8 18.2 13000 12171 15010 10141 9252 12039 838 856 871 4.2 5.1 9427 9884 651 665 11649 12155 7174 6711 8607 8520 9427 9449 1 14.9 14237 13329 11211 10239 887 906 4.7 4.3 67 O 10349 680 12669 6178 8072 9314 15.2 10821 695 13191 5151 7120 9263 15.6 Units are complete packages containing refrigeration 11302 709 13722 6069 8318 15.9 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 8654 726 11130 6586 7901 8654 11.9 safety controls: Overload protection for motors, high and low 9073 742 11604 6161 7821 8674 12.2 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 9500 758 12086 5672 7410 8550 12.5 Extended range option includes expansion valve metering 9934 774 12576 4728 6536 8503 12.8 device, insulated water coil and solid state lockout controls. 10374 791 13072 5571 7636 13.1 7908 803 10649 6018 7220 7908 9.8 8291 821 11093 5630 7147 7926 10.1 100 O 67 O 8681 839 11544 5183 6771 7813 10.3 Phone: (954) 7765471 9077 857 12002 4321 5973 7770 10.6 Fax: (800) 7765529 9480 875 12466 5091 6977 10.8 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM009IP6ISO.P65 Rev: 11399

Compressor Min. Max. 115160 0 8.9 50.0 2.20 0.10 13.0 20 208/230160 1 5.0 31.0 0.96 0.10 7.2 15 265160 2 4.0 22.9 0.85 0.10 5.9 15 Speed High 425 410 390 371 350 325 300 Medium 410 395 375 355 330 305 Low 385 370 350 330 305 All performance at 400 CFM and 3.0 GPM PACKAGE UNITS EM012 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 400 CFM and 3.0 GPM 11500 11.1 14500 4.2 13000 15.7 11000 3.2 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 0.97 4 3/8 14 Size Net Ship 4x7 122 132 ENERGYMISER 1.5 2.1 1.8 3.3 2.2 5.1 2.6 7.4 3.0 11.0 3.4 13.5 Water Capacity Absorb. COP 50 O 12740 724 15210 9695 11632 12740 17.6 12305 9073 947 3.8 13358 740 15882 9070 11515 12770 18.1 11671 8378 965 3.5 13986 756 16565 8350 10909 12587 18.5 10926 7565 985 3.3 14624 772 17259 6961 9623 12519 18.9 13849 10430 1002 4.1 15273 12066 12651 789 791 808 17964 14764 15409 9182 8590 8202 11016 10905 11241 12066 12095 19.4 15.3 15.7 13136 12298 15393 9652 1021 8741 1042 11783 1058 3.8 3.5 4.3 67 O 13246 13851 826 844 16064 16730 7908 6593 10332 9114 11921 11856 16.0 16.4 14600 13668 10922 1078 9914 1101 4.0 3.6 14465 862 17405 7768 10646 16.8 16857 13039 1119 4.4 11412 11965 859 878 14342 14961 8685 8125 10419 10314 11412 11439 13.3 13.6 15989 14969 12099 1140 10998 1164 4.1 3.8 67 O 12528 897 15589 7479 9772 11275 14.0 13100 916 16226 6236 8620 11214 14.3 Units are complete packages containing refrigeration 13681 936 16874 7347 10069 14.6 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 10476 963 13760 7972 9564 10476 10.9 safety controls: Overload protection for motors, high and low 10984 984 14341 7458 9468 10500 11.2 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 11500 1006 14931 6866 8970 10350 11.4 Extended range option includes expansion valve metering 12025 1027 15530 5724 7912 10293 11.7 device, insulated water coil and solid state lockout controls. 12558 1049 16137 6744 9243 12.0 9572 1069 13221 7284 8739 9572 9.0 10036 1093 13766 6815 8651 9595 9.2 100 O 67 O 10508 1117 14319 6273 8196 9457 9.4 Phone: (954) 7765471 10988 1141 14881 5230 7230 9405 9.6 Fax: (800) 7765529 11475 1165 15451 6162 8446 9.8 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM012IP6ISO.P65 Rev:92203

Compressor Min. Max. 208/230160 1 6.8 31.2 0.96 0.10 9.5 15 265160 2 5.8 27.0 0.85 0.10 8.1 15 Speed High 540 515 490 460 430 390 340 Medium 410 400 390 380 360 330 Low 300 290 280 All performance at 500 CFM and 3.8 GPM PACKAGE UNITS EM015 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 500 CFM and 4.0 GPM 14500 11.5 20000 4.2 16500 16.5 15000 3.4 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 1.42 3 3/8 14 Size Net Ship 4x7 139 150 ENERGYMISER 1.9 3.0 2.3 4.4 2.8 6.8 3.3 9.4 3.8 12.5 4.3 16.0 Water Capacity Absorb. COP 50 O 16397 917 19526 12478 14970 16397 17.9 16855 12545 1263 3.9 17192 938 20391 11673 14819 16435 18.3 15987 11596 1287 3.6 18000 18822 958 979 21269 22161 10746 8959 14040 12385 16200 16111 18.8 19.2 14967 18972 10484 1314 14411 1337 3.3 4.2 19657 15529 16281 999 1001 1024 23067 18946 19774 11817 11055 10556 14178 14035 14467 15529 15565 19.7 15.5 15.9 17995 16847 21086 13348 1362 12103 1390 16274 1410 3.9 3.6 4.4 67 O 17047 17825 18616 1046 1068 1091 20616 21471 22339 10177 8485 13297 11729 9997 15342 15258 13701 16.3 16.7 17.1 20000 18724 23093 15097 1437 13718 1467 18003 1492 4.1 3.7 14688 15400 1088 1112 18399 19193 11177 10457 13410 13275 14688 14722 13.5 13.9 21904 20506 16718 1520 15212 1552 4.2 3.9 67 O 16124 1136 20000 9626 12577 14512 14.2 16860 1160 20819 8025 11094 14432 1 Units are complete packages containing refrigeration 17608 1185 21651 9456 12960 14.9 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 13482 1220 17644 10260 12309 13482 11.1 safety controls: Overload protection for motors, high and low 14135 1247 18389 9598 12185 13513 11.3 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 14800 1274 19147 8836 11544 13320 11.6 Extended range option includes expansion valve metering 15476 1301 19916 7366 10183 13247 11.9 device, insulated water coil and solid state lockout controls. 16162 1329 20697 8679 11895 12.2 12319 1355 16941 9374 11247 12319 9.1 12916 1385 17641 8770 11133 12347 9.3 100 O 67 O 13523 1415 18351 8073 10548 12171 9.6 Phone: (954) 7765471 14140 1445 19072 6731 9304 12104 9.8 Fax: (800) 7765529 14768 1476 19804 7930 10869 10.0 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM015IP6ISO.P65 Rev:11399

Compressor Min. Max. 208/230160 1 9.0 48.0 1.8 0.25 13.1 20 265160 2 7.7 42.0 1.6 0.25 11.2 15 Speed High 770 700 680 650 610 570 530 Medium 670 650 615 570 530 Low 560 520 510 All performance at 650 CFM and 4.7 GPM PACKAGE UNITS EM018 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 650 CFM and 5.0 GPM 18000 12.5 22000 4.4 21000 17 17500 3.8 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 1.88 3 3/8 14 Size Net Ship 9x7 166 177 ENERGYMISER 2.3 4.4 2.9 7.2 3.5 10.7 4.1 14.8 4.7 19.4 5.3 24.9 Water Capacity Absorb. COP 50 O 20496 985 23857 15597 18713 20496 20.8 21020 16489 1328 4.6 21490 1007 24926 14591 18524 20544 21.3 19938 15322 1353 4.3 22500 23527 1029 1051 26011 27114 13433 11199 17550 15481 20250 20139 21.9 22.4 18666 23715 13953 1381 18920 1405 4.0 4.9 24571 19411 20352 1073 1076 1100 28233 23083 24105 14772 13819 13195 17722 17544 18084 19411 19457 22.9 18.0 18.5 22494 21059 26357 17608 1432 16071 1462 21297 1483 4.6 4.2 5.2 67 O 21309 22282 23270 1124 1148 1173 25144 26199 27271 12721 10606 16621 14661 12496 19178 19073 17127 19.0 19.4 19.8 25000 23405 28867 19844 1511 18142 1543 23516 1568 4.8 4.4 5.4 18360 19250 1168 1194 22345 23324 13972 13071 16763 16593 18360 18403 15.7 16.1 27381 25634 21929 1598 20068 1631 5.0 4.6 67 O 20155 1220 24318 12033 15721 18140 16.5 21075 1246 25327 10032 13867 18040 16.9 Units are complete packages containing refrigeration 22010 1273 26352 11819 16199 17.3 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 16852 1310 21323 12825 15386 16852 12.9 safety controls: Overload protection for motors, high and low 17669 1339 22239 11997 15231 16892 13.2 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 18500 1369 23169 11045 14430 16650 13.5 Extended range option includes expansion valve metering 19345 1398 24114 9208 12729 16559 13.8 device, insulated water coil and solid state lockout controls. 20203 1428 25074 10849 14869 14.2 15398 1455 20364 11718 14059 15398 10.6 16145 1488 21220 10962 13917 15435 10.9 100 O 67 O 16904 1520 22090 10092 13185 15214 11.1 Phone: (954) 7765471 17676 1553 22973 8414 11631 15130 11.4 Fax: (800) 7765529 18460 1586 23870 9913 13586 11.6 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM018IP6ISO.P65 Rev 11399

Compressor Min. Max. 208/230160 1 9.4 49.0 1.8 0.25 13.6 20 265160 2 8.2 44.0 1.6 0.25 11.9 20 Speed High 900 850 800 760 710 690 680 670 Medium 750 720 690 670 Low 670 All performance at 850 CFM and 5.8 GPM PACKAGE UNITS EM024 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 850 CFM and 6.0 GPM 23000 14.0 29000 4.9 26000 21.0 23000 4.2 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 2.12 3 3/8 14 Size Net Ship 9x7 175 187 ENERGYMISER 2.9 2.2 3.6 3.5 4.4 5.3 5.1 7.5 5.8 10.3 6.5 11.8 Water Capacity Absorb. COP 50 O 26589 1256 30875 20234 24276 26589 21.2 25225 19786 1594 4.6 27878 1284 32259 18929 24031 26652 21.7 23926 18385 1624 4.3 29189 30521 1312 1340 33666 35094 17426 14528 22767 20083 26270 26126 22.2 22.8 22399 28458 16743 1658 22705 1686 4.0 4.9 31876 25183 26404 1369 1364 1395 36545 29838 31162 19164 17928 17117 22992 22760 23460 25183 25242 23.3 18.5 18.9 26993 25271 31628 21131 1718 19286 1754 25557 1779 4.6 4.2 5.2 67 O 27645 28907 30190 1425 1456 1487 32507 33874 35261 16504 13760 21563 19021 16212 24881 24744 22219 19.4 19.9 20.3 30000 28086 34641 23814 1813 21771 1851 28218 1882 4.8 4.4 5.4 23818 24973 1475 1508 28852 30118 18126 16957 21746 21527 23818 23874 16.1 16.6 32857 30761 26313 1918 24080 1958 5.0 4.6 67 O 26147 1541 31405 15610 20395 23532 17.0 27341 1574 32712 13014 17990 23404 17.4 Units are complete packages containing refrigeration 28554 1608 34038 15333 21015 17.8 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 21862 1645 27476 16637 19960 21862 13.3 safety controls: Overload protection for motors, high and low 22922 1682 28660 15564 19759 21914 13.6 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 24000 1719 29864 14328 18720 21600 14.0 Extended range option includes expansion valve metering 25096 1755 31085 11945 16513 21482 14.3 device, insulated water coil and solid state lockout controls. 26209 1793 32326 14074 19290 14.6 19977 1814 26167 15202 18239 19977 11.0 20945 1855 27273 14222 18055 20024 11.3 100 O 67 O 21930 1895 28396 13092 17105 19737 11.6 Phone: (954) 7765471 22931 1936 29536 10915 15089 19629 11.8 Fax: (800) 7765529 23948 1977 30693 12860 17626 12.1 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM024IP6ISO.P65 Rev:11399

Compressor Min. Max. 208/230160 1 12.2 56.0 1.8 0.25 17.1 25 265160 2 10.2 55.0 1.6 0.25 14.4 25 208/230360 3 8.6 51.0 1.8 0.25 12.6 20 460360 4 4.3 25.0 0.9 0.25 6.3 15 Speed High 1250 1170 1120 1070 940 830 740 650 Medium 1050 980 920 830 760 700 Low 975 910 870 740 640 All performance at 950 CFM and 7.0 GPM PACKAGE UNITS EM028 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 950 CFM and 7.0 GPM 28000 13.1 32000 4.7 32000 18.9 26000 4.0 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 2.29 3 3/8 14 Size Net Ship 9x7 203 220 ENERGYMISER 3.5 3.4 4.4 5.3 5.0 7.4 5.8 10.3 7.0 13.6 8.8 21.4 Water Capacity Absorb. COP 50 O 31015 1441 35932 23603 28317 31015 21.5 28084 21557 1913 4.3 32519 1473 37544 22080 28031 31088 22.1 26638 19988 1949 4.0 34048 35602 1505 1537 39183 40848 20327 16947 26557 23426 30643 30476 22.6 23.2 24938 31648 18150 1990 24747 2023 3.7 4.6 37182 29379 30804 1570 1566 1601 42539 34724 36266 22358 20916 19967 26823 26553 27366 29379 29448 23.7 18.8 19.2 30019 28104 35213 22987 2061 20925 2104 27930 2135 4.3 3.9 4.8 67 O 32252 33724 35221 1636 1671 1707 37834 39426 41044 19254 16053 25157 22191 18913 29027 28868 25922 19.7 20.2 20.6 33400 31269 38567 25979 2175 23693 2220 30861 2258 4.1 5.0 27779 29126 1693 1730 33554 35029 21140 19776 25362 25106 27779 27844 16.4 16.8 36581 34247 28730 2301 26232 2349 4.7 4.3 67 O 30495 1768 36527 18206 23786 27446 17.2 31887 1806 38049 15178 20982 27295 17.7 Units are complete packages containing refrigeration 33302 1844 39595 17883 24510 18.1 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 25506 1888 31948 19410 23287 25506 13.5 safety controls: Overload protection for motors, high and low 26743 1930 33327 18158 23052 25566 13.9 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 28000 1972 34728 16716 21840 25200 14.2 Extended range option includes expansion valve metering 29278 2014 36151 13936 19265 25062 1 device, insulated water coil and solid state lockout controls. 30577 2057 37596 16420 22505 14.9 23306 2082 30411 17736 21279 23306 11.2 24436 2129 31699 16592 21064 23361 11.5 100 O 67 O 25585 2175 33006 15274 19956 23027 11.8 Phone: (954) 7765471 26753 2222 34334 12734 17603 22901 12.0 Fax: (800) 7765529 27940 2269 35681 15004 20564 12.3 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM028IP6ISO.P65 Rev:11399

Compressor Min. Max. 208/230160 1 14.7 81.0 1.8 0.25 20.2 35 265160 2 12.8 72.0 1.6 0.25 17.6 30 208/230360 3 10.7 70.0 1.8 0.25 15.2 25 460360 4 5.1 36.0 0.9 0.25 7.3 15 Speed High 1250 1170 1120 1070 940 830 740 650 Medium 1050 980 920 830 760 700 Low 975 910 870 740 640 All performance at 1000 CFM and 8.1 GPM PACKAGE UNITS EM031 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ARI / ISO 132561 PERFORMANCE DATA Rated at 1000 CFM and 7.5 GPM 32000 13.3 40000 4.7 37000 19.1 31500 3.7 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 2.29 3 3/8 14 Size Net Ship 9x7 210 220 ENERGYMISER 4.0 2.1 5.1 3.3 5.8 4.0 6.8 5.1 8.1 7.2 10.2 10.6 Water Capacity Absorb. COP 50 O 35446 1659 41107 26975 32362 35446 21.4 35059 26784 2425 4.2 37165 1696 42951 25235 32036 35529 21.9 33254 24823 2471 3.9 38912 40688 1733 1770 44825 46728 23230 19368 30351 26773 35021 34829 22.5 23.0 31132 39566 22525 2523 30843 2557 3.6 42494 33576 35204 1808 1815 1855 48662 39770 41535 25551 23903 22819 30655 30346 31275 33576 33655 23.5 18.5 19.0 37529 35134 44280 28641 2605 26061 2659 35124 2683 4.2 3.9 4.8 67 O 36859 38542 40252 1896 1937 1978 43328 45150 47000 22005 18346 28750 25360 21615 33173 32992 29625 19.4 19.9 20.4 42000 39320 49490 32672 2734 29797 2791 39842 2828 4.1 5.1 31748 33287 1966 2009 38454 40142 24160 22602 28986 28693 31748 31822 16.2 16.6 46942 43947 37112 2881 33912 2941 4.8 4.4 67 O 34852 2053 41857 20807 27185 31367 17.0 36443 2097 43598 17347 23979 31195 17.4 Units are complete packages containing refrigeration 38060 2142 45367 20438 28012 17.8 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 29150 2192 36631 22183 26614 29150 13.3 safety controls: Overload protection for motors, high and low 30563 2241 38210 20752 26345 29218 13.6 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 32000 2290 39813 19104 24960 28800 14.0 Extended range option includes expansion valve metering 33461 2339 41442 15927 22017 28642 14.3 device, insulated water coil and solid state lockout controls. 34945 2389 43096 18766 25720 14.6 26636 2420 34894 20270 24318 26636 11.0 27927 2474 36368 18962 24073 26698 11.3 100 O 67 O 29240 2528 37866 17456 22807 26316 11.6 Phone: (954) 7765471 30575 2582 39386 14554 20118 26172 11.8 Fax: (800) 7765529 31931 2637 40929 17147 23501 12.1 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM031IP6ISO.P65 Rev:11599

Compressor Min. Max. 208/230160 1 14.7 81.0 3.9 0.5 22.3 35 265160 2 12.8 72.0 2.3 0.5 18.3 30 208/230360 3 10.1 70.0 3.9 0.5 16.5 25 460360 4 5.0 36.0 2.0 0.5 8.3 15 Speed High 1500 1440 1370 1290 1210 1120 1000 900 Medium 1410 1350 1290 1220 1150 1060 900 Low 1290 1250 1200 1150 1080 1000 All performance at 1200 CFM and 8.6 GPM PACKAGE UNITS EM036 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 1200 CFM and 9.0 GPM 34000 14.0 40000 4.7 38000 20.1 31500 4.0 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 3.5 3 3/8 14 Size Net Ship 9x7 240 260 ENERGYMISER 4.3 2.4 5.3 4.0 6.1 4.7 7.1 6.3 8.6 9.5 10.6 1 Water Capacity Absorb. COP 50 O 38770 1814 44961 29504 35397 38770 21.4 35056 26791 2422 4.2 40650 1855 46977 27601 35040 38861 21.9 33251 24830 2468 3.9 42561 44504 1895 1936 49027 51109 25409 21184 33198 29284 38305 38095 22.5 23.0 31129 39560 22533 2520 30850 2553 3.6 46478 36724 38505 1977 1986 2030 53223 43499 45430 27947 26145 24959 33529 33191 34208 36724 36810 23.5 18.5 19.0 37523 35129 44280 28648 2601 26069 2655 35118 2685 4.2 3.9 4.8 67 O 40315 42155 44026 2074 2119 2164 47391 49384 51408 24068 20066 31446 27738 23642 36284 36085 32403 19.4 19.9 20.3 42000 39320 49500 32665 2736 29790 2793 39859 2826 4.1 5.1 34724 36407 2149 2197 42058 43903 26425 24721 31703 31383 34724 34805 16.2 16.6 46951 43955 37128 2879 33927 2939 4.8 4.4 67 O 38119 2245 45779 22757 29733 34307 17.0 39859 2293 47684 18973 26227 34119 17.4 Units are complete packages containing refrigeration 41628 2342 49618 22354 30638 17.8 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 31883 2398 40066 24263 29109 31883 13.3 safety controls: Overload protection for motors, high and low 33428 2451 41793 22698 28815 31957 13.6 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 35000 2505 43547 20895 27300 31500 14.0 Extended range option includes expansion valve metering 36598 2559 45329 17421 24081 31328 14.3 device, insulated water coil and solid state lockout controls. 38221 2613 47137 20525 28131 14.6 29133 2647 38165 22170 26598 29133 11.0 30545 2706 39777 20740 26330 29201 11.3 100 O 67 O 31981 2765 41415 19093 24945 28783 11.6 Phone: (954) 7765471 33441 2824 43078 15918 22004 28625 11.8 Fax: (800) 7765529 34925 2884 44766 18755 25705 12.1 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM036IP6ISO.P65 Rev:11399

Compressor Min. Max. 208/230160 1 18.9 96.0 3.9 0.5 27.5 45 208/230360 3 12.2 75.0 3.9 0.5 19.2 30 460360 4 6.2 40.0 2.0 0.5 9.8 15 575360 5 4.9 31.0 2.6 0.75 8.7 15 Speed High 1260 1180 1100 1030 960 870 810 620 Medium 1210 1150 1070 1010 940 850 750 Low 1160 1100 1040 980 910 830 All performance at 1150 CFM and 9.8 GPM PACKAGE UNITS EM041 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 1150 CFM and 9.0 GPM 38500 12.5 49000 4.3 41000 16.1 39000 3.8 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 2.29 4 3/8 14 Size Net Ship 9x7 235 245 ENERGYMISER 4.9 3.1 6.1 4.7 7.0 6.2 8.2 8.6 9.8 12.4 12.2 19.1 Water Capacity Absorb. COP 50 O 41886 2117 49109 31876 38242 41886 19.8 41555 31006 3092 3.9 43917 2164 51300 29820 37857 41985 20.3 39415 28667 3150 3.7 45982 48081 2211 2259 53526 55787 27451 22887 35866 31637 41384 41157 20.8 21.3 36900 47096 25928 3216 36028 3244 3.4 4.3 50214 40223 42173 2306 2328 2380 58084 48168 50294 30610 28636 26965 36724 36353 36958 40223 40318 21.8 17.3 17.7 44671 41821 52714 33394 3305 30309 3374 41124 3397 4.0 3.6 67 O 44156 46172 48220 2432 2484 2537 52454 54648 56876 26361 21978 34442 30381 25894 39740 39523 35490 18.2 18.6 19.0 50000 46810 58544 38191 3461 34754 3533 46388 3563 4.2 3.9 4.8 38554 40423 2542 2598 47227 49289 29340 27447 35200 34845 38554 38645 15.2 15.6 55530 51987 43144 3630 39343 3706 4.1 67 O 42324 2655 51383 25267 33013 38092 15.9 44256 2712 53510 21066 29120 37883 16.3 Units are complete packages containing refrigeration 46220 2770 55669 24820 34018 16.7 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 35982 2867 45764 27382 32851 35982 12.6 safety controls: Overload protection for motors, high and low 37726 2931 47725 25616 32520 36066 12.9 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 39500 2995 49717 23582 30810 35550 13.2 Extended range option includes expansion valve metering 41303 3059 51740 19660 27177 35355 13.5 device, insulated water coil and solid state lockout controls. 43136 3124 53794 23164 31748 13.8 33150 3198 44060 25227 30266 33150 10.4 34757 3269 45909 23600 29960 33228 10.6 100 O 67 O 36391 3340 47787 21725 28385 32752 10.9 Phone: (954) 7765471 38052 3412 49693 18113 25038 32573 11.2 Fax: (800) 7765529 39741 3484 51628 21341 29249 11.4 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM041IP6ISO.P65 Rev:12199

Compressor Min. Max. 208/230160 1 17.1 96.0 3.9 0.5 25.3 40 208/230360 3 11.1 75.0 3.9 0.5 17.8 25 460360 4 5.6 40.0 2.0 0.5 9.0 15 575360 5 4.4 31.0 2.6 0.75 8.1 15 Speed High 1560 1500 1420 1340 1260 1170 1070 950 Medium 1470 1410 1340 1270 1200 1110 1010 Low 1340 1300 1250 1200 1130 1050 All performance at 1500 CFM and 10.4 GPM PACKAGE UNITS EM042 HIGHEFFICIENCY WATER SOURCE HEAT PUMPS ISO 132561 PERFORMANCE DATA Rated at 1500 CFM and 10.0 GPM 41500 12.8 50500 4.3 44000 16.9 40000 3.9 table for GLHP performance Water Wet Capacity Rejection Ent. Air Temp. EER For extended range performance beyond the ranges shown on the tables below, the extended range option must be installed. 3.5 3 3/8 14 Size Net Ship 9x7 267 287 ENERGYMISER 5.2 3.9 6.5 5.3 7.4 6.9 8.7 9.4 10.4 14.0 13.0 21.7 Water Capacity Absorb. COP 50 O 44537 2226 52132 33893 40663 44537 20.0 42723 32134 3103 4.0 46696 2275 54460 31707 40252 44642 20.5 40523 29734 3162 3.8 48892 51124 2325 2375 56825 59227 29189 24335 38136 33640 44003 43762 21.0 21.5 37937 48256 26923 3228 37144 3256 3.4 4.3 53392 42769 44843 2425 2450 2504 61667 51129 53387 32547 30448 28672 39048 38654 39297 42769 42870 22.0 17.5 17.9 45771 42851 53768 34450 3318 31293 3387 42128 3412 4.0 3.7 4.6 67 O 46951 49094 51272 2559 2614 2669 55682 58013 60381 28030 23369 36622 32304 27533 42256 42025 37737 18.3 18.8 19.2 51000 47746 59595 39140 3476 35638 3549 47419 3569 4.3 3.9 4.9 40995 42982 2682 2741 50145 52335 31197 29185 37428 37051 40995 41091 15.3 15.7 56527 52920 44121 3636 40255 3712 4.6 4.2 67 O 45003 2801 54560 26867 35102 40503 16.1 47057 2861 56820 22399 30964 40281 16.4 Units are complete packages containing refrigeration 49145 2922 59115 26391 36171 16.8 compressor, reversing valve, capillary tube metering device, and water to refrigerant heat exchanger. Also included are 38259 3048 48660 29115 34931 38259 12.6 safety controls: Overload protection for motors, high and low 40114 3116 50746 27237 34578 38349 12.9 refrigerant pressure switches and a lockout control circuit. 85 O 67 O 42000 3184 52864 25074 32760 37800 13.2 Extended range option includes expansion valve metering 43917 3252 55015 20905 28898 37593 13.5 device, insulated water coil and solid state lockout controls. 45866 3321 57198 24630 33757 13.8 35248 3438 46978 26823 32181 35248 10.3 36956 3514 48947 25093 31856 35330 10.5 100 O 67 O 38694 3591 50946 23100 30181 34825 10.8 Phone: (954) 7765471 40460 3668 52976 19259 26623 34634 11.0 Fax: (800) 7765529 42255 3746 55037 22691 31100 11.3 http://www.fhpmfg.com As a result of continuing research and development, specifications are subject to change without notice. EM042IP6ISO.P65 Rev:12199