Section H Overview You re sure to find a solution for your cleaning and rinsing needs in our comprehensive line of hand-held spray guns. Options range from a gentle spray to a high-impact solid stream. All our spray guns are durable and efficient. Many of our guns also offer: Specially designed handles to improve control and reduce operator fatigue. Smooth-pull triggers to enable accurate and consistent flow control. Textured grips to minimize the chance for slippage and accidents. Leak-free operation. A complete line of accessories complements our spray guns. Front shut-off extensions, extensions, inlet/outlet adapters, connectors and strainers are available to ensure easy, trouble-free operation. Table of Contents High Pressure... H3 Low Pressure.................................. H5 Low-Medium Pressure... H9 Front Shut-Off Spray Gun s... H11 Spray Gun s... H12 and Outlet Spray Gun Adapters... H16 Spray Gun Swivel Connectors and High Pressure Liquid Strainers... H17 Spray Guns H1
Optimization Tips Never point a spray gun at another person or yourself. Injury can result. Use the trigger lock feature when the gun is not in use to avoid accidental discharge. Add an extension and handle to improve spray gun stability. Be sure to use the correct spray gun for your pressure and flow range to ensure safety and achieve maximum performance. The use of steam with spray guns is not recommended. Spray guns are rated for optimal flow rates. Use tips that match no performance improvements will result from using a tip with a higher capacity than the spray gun. Eliminate water hammer and pressure spikes by using an unloader valve. Add a swivel to the hose to ensure easy movement of the spray gun and hose. Always use a check valve or similar bypass valve when using high pressures to ensure safety. Check and tighten fluid connections if necessary to avoid leaks. Use a spray gun with a weep feature to prevent freezing in cold environments. In-line strainers provide filtering to protect gun and purity of sprayed liquid. Proper selection of a spray gun, for your application, will reduce operator fatigue. Trigger Lock Swivel Accessories Check Valve Gun H2
, High Pressure Features and Benefits Ultimate versatility is available with a complete selection of UniJet spray tips to meet pattern and flow specifications. Available outlet adapters convert any standard thread allowing the attachment of many optional accessories. Standard one-piece nozzles, such as VeeJet flat spray nozzles, can be used when mated with proper adapters. Ergonomic designs assure positive control and operator comfort even at maximum flow and pressure conditions. Sturdy design and materials including nylon handles and trigger guards, forged brass valve bodies, Buna-N or Viton stem seals, PTFE valve seats and stainless steel working parts mean long, productive equipment life. Optional weep feature (30A and 70) helps prevent freezing in cold conditions. 30A 60 70 80 PW4000A PW4000AS Spray Guns Optimization Tips See page H2 for optimization tips. Applications Adhesive spraying Lubricating Car wash Paint spray Floor/rug cleaning Pest control High pressure cleaning Pressure wash See Also Accessories s /outlet adapters Swivel connectors AA70 GunJet http:// H3
, High Pressure Specifications High Pressure Model Pressure (bar) Capacity (l/min) Temperature F ( C) 30A 105 19 200 (93) Outlet Length (cm) Width (cm) Height (cm) Net Weight (kg) THD 20.32 2.86 16.67.43 Special Features Nylon handle/ trigger guard. 60 175 23 300 (150) 3/8" NPT or THD 22.23 3.65 16.51.45 Stainless steel body available. 70 345 38 300 (150) 3/8" NPT (F) or 19.9 3.4 19.2.715 Easy trigger pull. Stainless steel valve seal and ball. 80 210 38 300 (150) 3/8" NPT or THD or 1/4", 3/8" NPT or 22.86 4.13 17.46 1.02 Nylon handle. Trigger guard. PW4000A 275 38 300 (150) 1/4", 3/8" NPT or 1/4", 3/8" NPT or 22.23 3.18 19.69.68 Fatigue-reducing trigger. PW4000AS 275 38 300 (150) 3/8" NPT or swivel 1/4", 3/8" NPT or 22.23 3.18 19.69.68 Bottom trigger pivot and inlet swivel. Ordering Info Complete Spray Gun Assembly AA60 3/8 l l GunJet Number H4
, Low Pressure Features and Benefits All GunJet low pressure spray guns are designed to meet the special needs of low pressure applications. Versatile GunJet low pressure spray guns are designed for use with a wide variety of spray tips to meet particular pattern and flow specifications. Available outlet adapters convert any standard thread allowing the attachment of many optional accessories. Standard one-piece nozzles, such as VeeJet flat spray nozzles, can be used when mated with proper adapters. Ergonomic designs assure positive control and operator comfort even at maximum flow and pressure conditions. Sturdy design and materials including nylon and polypropylene handles and trigger guards, forged brass valve bodies, Buna-N or Viton stem seals, PTFE valve seats and stainless steel working parts mean long, productive equipment life. Key feature overview for 23624-30L: For low pressure spot application of chemicals. Features an adjustable metering assembly that enables the applicator to discharge precisely metered volumes from 1 to 16 ml with a single pull of the trigger. Automatically recharges for the next dosage when the trigger is released. Key feature overview for CU150A: For general clean-up applications. Offers versatility and maximum comfort. Features easy-change color-coded spray caps with three flow capacities. Spray pattern can be adjusted from a solid stream to a 50 hollow cone pattern. Available with optional repair kits. Can be ordered in brass or lightweight aluminum with a corrosion-resistant rubber outer cover. Complete line of accessories for 22650-PP TriggerJet spray gun: s: 15" (381 mm) or 24" (610 mm). Part number 22665-PP. 45 adapter. Part number 22673-PPB. Straight adapter. Part number 22664-PPB. Adjustable ConeJet spray tip. Part number 5500-PPB. UniJet strainer. Part number 8079-50-PP. Key feature overview for 23623-31-1/4F: Provides an adjustable metering assembly which allows the applicator to discharge precisely metered volumes from 1 to 16 ml with a single pull of the trigger. Automatically recharges for the next dosage when the trigger is released. Trigger valve inlet handle options for 36, 4688, 6104, 6466 and 6590 with BSPT (M) inlet connections: Rubber covered handle with a 1/4" NPS (M) hose inlet connection. Part number 4727. 1/8" brass pipe handle. 3/8" ID hose slips easily over the pipe handle. Part number 4725. Rubber covered handle with a 3/4" garden hose thread connection. Part number 4754. Internal strainer with choice of mesh sizes and a 1/4" NPT or connection. Part number 5820. Spray Guns H5
, Low Pressure 30L 30L-PP 23624-30L 30-20940 60-21580 30L-26323 CU150A 23623-31-1/4F 31-39430 22650-PP 36 4688 6104 6466 6590 Optimization Tips See page H2 for optimization tips. Applications General clean-up Low pressure cleaning Spot application of chemicals See Also Accessories s /outlet adapters Swivel connectors http:// H6
, Low Pressure Specifications Low Pressure Model Pressure (bar) Capacity (l/min) Temperature F ( C) Outlet Length (cm) Width (cm) Height (cm) Net Weight (kg) Special Features 30L 17 19 200 (93) UniJet THD 20.32 2.86 16.67.43 Nylon handle. Trigger guard. 30L-PP 10 19 120 (50) 20.32 2.86 16.67.26 Polypropylene handle. Trigger guard. 23624-30L 5.2 1 to 16 ml dosage range 200 (93) 25.08 5.35 16.67.68 Adjustable metering. Auto recharge. 30-20940 17 38 300 (150) 20.80 2.86 16.67.34 Trigger activated variable spray pattern. 60-21580 17 60 300 (150) 3/8" NPT or 22.86 3.65 16.51.55 Trigger activated variable spray pattern. 30L-26323 17 19 200 (93) 20 2.86 16.67.37 Uses Quick UniJet caps, seat gaskets and spray tips. Corrosion resistant. CU150A 10 38 to 83 200 (93) 1/2" NPT or 16.5 5.7 16.5 1 Changeable spray caps. Adjustable spray pattern solid to 50 hollow cone. Corrosion resistant. Rubber outer cover white or black. Repair and replacement parts available. Also available in aluminum (weight.62 kg). Spray Guns Ordering Info Complete Spray Gun Assembly CU150A AL 22 l l l GunJet Type Code Capacity Complete Spray Gun Assembly 22650 PP 1/4 l l l GunJet Type Code H7
, Low Pressure Specifications Specialty Low Pressure Pressure (bar) Capacity (l/min) 23623-31-1/4F MeterJet 5.2 1 to 16 ml 31-39430 34 19 1/4" NPS or BSPT (M) Outlet UniJet THD Special Features Adjustable metering. Auto recharge. Trigger activated variable spray pattern. Drip-free shut off. Brass body. Stainless steel trigger. Buna-N bumper. 22650-PP TriggerJet 10 7.6 1/4" or 3/8" hose or Corrosion resistant polypropylene construction. UniJet strainer available. Durable Viton diaphragm. 36 Trigger Valve 10 27 1/4" or 3/8" NPT or 1/4" or 3/8" NPT or Brass or stainless steel. 4688 Trigger Valve 17 7.6 Brass or stainless steel. 6104 Trigger Valve 17 7.6 Brass or stainless steel. 6466 Trigger Valve 17 7.6 THD Extra long trigger. 6590 Trigger Valve 17 7.6 Extra long trigger. GunJet spray gun used to clean grease from equipment and floor. H8
, Low-Medium Pressure Features and Benefits All are designed for use with UniJet spray tips to meet a wide variety of pattern and flow specifications. Available outlet adapters convert any standard thread allowing the attachment of many optional accessories. Standard one-piece nozzles, such as VeeJet flat spray nozzles, can be used when mated with proper adapters. Ergonomic designs assure positive control and operator comfort even at maximum flow and pressure conditions. For safety, trigger guards are designed to prevent accidental discharge. Sturdy design and materials including nickel-plated, brass or stainless steel inlet bodies, PTFE or nylon valve seats and stainless steel stems and brass guides mean long, productive equipment life. Optimization Tips See page H2 for optimization tips. See Also Accessories s /outlet adapters In-line strainers Swivel connectors http:// 23L AA23L-45885 23H 31 36533-60 43LD 43LC 43HD Spray Guns 43HC Ordering Info Complete Spray Gun Assembly AA23L SS l l GunJet Number Code H9
, Low-Medium Pressure Specifications Low-Medium Pressure Model Pressure (bar) Capacity (l/min) Temperature F ( C) 23L 17 19 200 (93) 1/4" NPS (M) Outlet UniJet THD Length (cm) Width (cm) Height (cm) Net Weight (kg) 15.24 2.70 18.42.43 Special Features Aluminum alloy handle. PTFE valve seat. Stainless steel stem. Brass guide. Nickel-plated inlet body. AA23L- 45885 17 3.18 200 (93) 1/4" NPS (M) 15.24 2.70 18.42.45 Drop adjusting nut. Tapered needle. Captured valve seat. Nickel-plated inlet body. 23H 70 19 200 (93) 1/4" NPS (M) 15.24 2.70 18.42.45 31 35 19 1/4" NPS (M) or NPT or 13.97 2.54 8.25.35 Drip-free shut-off. Trigger lock (optional). 36533-60 41 45 200 (93) 3/8" NPT or 22.22 3.65 16.51.45 Durable nylon handle/trigger guard. Trigger lock off. 43LD 14 57 200 (93) 1/2" NPT or 20.32 3.50 21.27 1 Brass inlet body. 43LC 14 57 200 (93) 1/2", 3/4" NPT or 1/2", 3/4" NPT or 20.32 3.50 21.27 1 43HD 56 57 200 (93) 1/2" NPT or 22.86 3.50 21.27 1 43HC 56 57 200 (93) 1/2", 3/4" NPT or 1/2", 3/4" NPT or 22.86 3.50 21.27 1 H10
Front Shut-Off s 23L-7676 30L-22425 31-12090 Optimization Tips See page H2 for optimization tips. See Also Data Sheet 7676 Data Sheet 30L-22425 Data Sheet 12092 http:// Specifications GunJet Model GunJet Plus Type Pressure (bar) Capacity (l/min) Temperature F ( C) Outlet Lengths (mm) GunJet Special Features 23L-7676 AA23L-7676 or AA23L-SS- 7676-SS 17 19 200 (93) 1/4" NPS (M) UniJet THD 203, 457, 610, 914, 1219 Brass or 303 Stainless Steel Brass or stainless steel 30L-22425 AA30L-22425 10 19 120 (50) 31-12090 AA31-12090 35 19 200 (93) 1/4" NPS (M) or 203, 457, 610, 914, 1219, 1524, 1829 203, 457, 610, 914 Brass Brass Brass Brass Drip-free shut-off with valve stem extending full length of extension. Spray Guns Ordering Info Complete Spray Gun Assembly AA23L SS 7676 18 SS l l l l l GunJet Type Code Type Length Code H11
Spray Gun s Specifications Gun No. Maximum Pressure (bar) 9004-SS 275 UniJet THD Outlet Special Features Stainless steel 11806 275 1/4" NPS (M) liquid recirculating 1/4" NPS (M) liquid recirculating Brass Stainless steel only available in 203 mm length. 15250 210 3/8" NPT or BSPT (M) Stainless steel or zinc-plated steel Adjustable hand grip. 20400 210 1/4" NPT or BSPT (M) BSPT (M) or 1/8" NPT or Stainless steel or zinc-plated steel 13781S 138 Mild steel Usually supplied with 7890 inlet cap and 13783 hollow cone spray tip (order cap and tip separately). Refer to Data Sheet 13775. 9702S 138 Mild steel Usually supplied with 7890 inlet cap and a tungsten carbide spray tip (order cap and tip separately). Refer to Data Sheet 9702-1. 9702A 138 Mild steel Projects spray at 90 angle. 9702C 138 Mild steel Curved body. 15699 70 Brass Rubber insulated (1219 mm length not rubber insulated). H12
Spray Gun s Specifications Gun No. Pressure (bar) Outlet Special Features 9527 70 UniJet THD Brass Curved, rubber insulated. CP12087 70 BSPT (M) BSPT (M) Aluminum 12086 70 Brass 17 Brass 203, 305, 457, 610, 762, 914 and 1219 mm 7715 35 Brass (203, 305, 457, 610, 914 and 1219 mm lengths also available in stainless steel) 14975 17 1/8" NPT or BSPT (M) Brass 6671 8.6 Brass (914 mm lengths also available in stainless steel) Curved body. Spray Guns 4673 8.6 Brass Curved with swivel nozzle body. 6960 7 Brass Siphon with adjustable flow. 22665 10 Polyester H13
Spray Gun s Spray Gun Compatibility No. 9004-SS 11806 15250 20400-1/4M 20400-1/8F 13781S 9702S 9702A 9702C 15699 9527 Length Available (mm) 22AUH 24AUA 30 60 80 23 43LD 43-11767- 1/4 43-11767- 3/8 43-12605 31 203 l l l l l l l l l l l 305 l l l l l l l l l l l 457 l l l l l l l l l l l 610 l l l l l l l l l l l 914 l l l l l l l l l l l 203 l l l l l l l l l l l 305 l l l l l l l l l l l 457 l l l l l l l l l l l 610 l l l l l l l l l l l 914 l l l l l l l l l l l 457 l l 914 l l 36-1/4 4688 6466 6104 6590 22650 457 l* l* l l l l l 914 l* l* l l l l l 457 l* l* l l l l l 914 l* l* l l l l l 254 l l l l l l l l l 406 l l l l l l l l l 1219 l l l l l l l l l 254 l l l l l l l l l 610 l l l l l l l l l 1219 l l l l l l l l l 1524 l l l l l l l l l 254 l l l l l l l l l 610 l l l l l l l l l 1219 l l l l l l l l l 1524 l l l l l l l l l 254 l l l l l l l l l 610 l l l l l l l l l 1219 l l l l l l l l l 1254 l l l l l l l l l 203 l l l l l l l l 457 l l l l l l l l 610 l l l l l l l l 914 l l l l l l l l 1219 l l l l l l l l 203 l l l l l l l l 457 l l l l l l l l 610 l l l l l l l l 914 l l l l l l l l 1219 l l l l l l l l *Use with 14643-1/4-SSP stainless steel adapter. H14
Spray Gun s Spray Gun Compatibility No. Length Available (mm) 22AUH 24AUA 30 60 80 23 43LD 43-11767- 1/4 43-11767- 3/8 43-12605 31 36-1/4 4688 6466 6104 6590 22650 203 l l l l CP12087 457 l l l l 610 l l l l 914 l l l l 203 l l l l l l 12086 457 l l l l l l 610 l l l l l l 914 l l l l l l 203 l l l l l l 305 l l l l 457 l l l l 7715 610 l l l l 762 l l l l 914 l l l l 1219 l l l l 14975 457 l l l l l l 203 l l l l l l 457 l l l l l l 6671 610 l l l l l l 762 l l l l l l 914 l l l l l l 1219 l l l l l l 203 l l l l l l 457 l l l l l l 610 l l l l l l 4673 762 l l l l l l 914 l l l l l l 1219 l l l l l l 1828 l l l l l l 6960 216 l l l l l l 22665 381 l 610 l Spray Guns Ordering Info Complete Assembly 7715 18 SS l l l Type Length Code H15
Spray Gun and Outlet Adapters 7029 3/4" garden hose thread (F) inlet connection 1/2" NPT or BSPT (M) outlet connection 13212 14269 4676 3/4" garden hose thread (F) inlet connection 3/8", 1/2" NPT or BSPT (M) outlet connection 3/4" garden hose thread (F) inlet connection 1/4" NPS (F) or 1/4" NPT (F) outlet connection THD UniJet (F) inlet connection 1/8", 1/4", 3/8", 1/2", 3/4" NPT or outlet conn. 14643 15572 7599 10997 THD UniJet (F) inlet connection 1/8", outlet connection THD UniJet inlet connection THD UniJet outlet connection 1/4", 3/8" NPT or inlet connection 1/4" NPS (F) outlet connection 1" 14 (M) inlet connection 1/4", 3/8" NPT or outlet connection Optimization Tips Specifications See page H2 for optimization tips. See Also Data Sheet 7035 Data Sheet 13223 Data Sheet 14353 Data Sheet 10896 Ordering Info Data Sheet 14721 Data Sheet 15578 Data Sheet 7599 http:// Spray Gun /Outlet Adapter Model No. 7029 13212 14269 4676 3/4" garden hose thread (F) 3/4" garden hose thread (F) 3/4" garden hose thread (F) THD UniJet (F) Outlet 1/2" NPT or BSPT (M) 3/8", 1/2" NPT or BSPT (M) 1/4" NPS (F) or 1/4" NPT (F) 1/8", 1/4", 3/8", 1/2", 3/4" NPT or Maximum Pressure (bar) 55 Brass 10.4 Brass 8.6 Brass 70 138 Brass and nickel-plated brass 303 Stainless Steel Complete Adapter Assembly 8.4 Nylon 4676 1/8 SS l l l Adapter Type Code 14643 15572 7599 THD UniJet (F) THD UniJet 1/4", 3/8" NPT or 1/8", 1/4" NPT or THD UniJet 1/4" NPS (F) 275 Nickel-plated steel 55 Brass 70 138 Nickel-plated brass Polished stainless steel 10997 1" 14 (M) 1/4", 3/8" NPT or 210 Stainless steel H16
Spray Gun Swivel Connectors and High Pressure Liquid Strainers 11990 15950 21550 1/4" to 1/2" NPT or inlet conn. 1/4" NPT or NPS (F) outlet conn. 1/4" to 1/2" NPT or BSPT (M) inlet conn. 1/4" NPS (M) outlet conn. 1/4" to 1/2" NPT or NPS (F) outlet conn. 3/8" NPT or BSPT (M) inlet conn. 3/8" NPT or inlet conn. 1/4", 3/8" NPT or inlet connection 1/4", 3/8" NPT or BSPT (M) outlet connection 9765 36466 36466L 36467 1/4" NPS (M) inlet connection 1/4" NPS (F) outlet connection 1/2", 5/8", 3/4" garden hose ID inlet conn. (1-3/16" long) 1/2" NPT or BSPT (M) threaded outlet conn. 3/4" garden hose ID inlet conn. (2-7/16" long) 1/2" NPT or BSPT (M) outlet connection 3/4" garden hose thread (F) inlet connection 1/2" NPT (M) threaded outlet conn. Spray Guns GunJet spray gun used in automotive industry to attach backing, foam and fabric to seats. H17
Spray Gun Swivel Connectors and High Pressure Liquid Strainers 21550-90NP 36560 8510 9770 1/4", 3/8" NPT (M) inlet connection 3/8" NPT or outlet connection 3/8" NPT (M) inlet conn. 3/8" NPS (F) outlet conn. Strainer 1/4" NPS (M) inlet conn. 1/4" NPS (F) outlet conn. Strainer 1/4" NPS (M) inlet conn. 1/4" NPS (F) outlet conn. 22629-SS Optimization Tips See page H2 for optimization tips. See Also http:// 22629 swivel nut branch tee is used with AA26AUH-24200 electric automatic spray guns to provide liquid recirculation. Data Sheet 15950 Data Sheet 21550 Data Sheet 9765 Data Sheet 21550-90 Data Sheet 36560 Data Sheet 8510 Data Sheet 9770 GunJet spray gun used to clean floors and equipment. H18
Spray Gun Swivel Connectors and High Pressure Liquid Strainers Specifications Model No. Outlet Maximum Pressure (bar) Temperature F ( C) Special Features 1/4" to 1/2" NPT or NPS (F) 11990 1/4" to 1/2" NPT or BSPT (M) 70 180 (82) Brass Leakproof hose, 360 swivel eliminates hose kinking and operator fatigue. 1/4" NPS (M) 1/4" to 1/2" NPT or NPS (F) 15950 3/8" NPT or BSPT (M) 3/8" NPT or 210 200 (93) Brass or stainless steel 21550 1/4", 3/8" NPT or 1/4", 3/8" NPT or BSPT (M) 103 200 (93) Brass 9765 1/4" NPS (M) 1/4" NPS (F) 275 Stainless steel 36466 36466L 1/2", 5/8", 3/4" garden hose ID (1-3/16" long) 3/4" garden hose ID (2-7/16" long) 1/2" NPT or BSPT (M) threaded 10 Brass 1/2" NPT or BSPT (M) 10 Brass Lock ring secures trigger of CU150A in fully engaged position. 36467 3/4" garden hose thread (F) 1/2" NPT (M) threaded 10 Brass For use with CU150A spray gun. 21550-90NP 1/4", 3/8" NPT (M) 3/8" NPT or 103 200 (93) Delrin bearings and Buna-N O-ring 36560 3/8" NPT (M) 3/8" NPS (F) 138 200 (93) Nickel-plated brass 8510 Strainer 1/4" NPS (M) 1/4" NPS (F) 275 Stainless steel 9770 Strainer 1/4" NPS (M) 1/4" NPS (F) 275 Stainless steel 22629-SS 1/2"-20 J.I.C. (M) 1/2"-20 J.I.C. (F) 138 Stainless steel Ceiling-mount. Boom swivel designed for ceiling mount. Choice of screen mesh sizes. Internal support prevents screen collapse at high pressure. Non-clogging tip protection and effortless handling of spray gun without twisting hose. Branch tee for AA26AUH-24200 for liquid recirculation. Spray Guns Ordering Info Spray Gun Connectors 11990-6 l Swivel Type Call for ordering information for other swivels and strainers. H19
Spray Gun Swivel Connectors and High Pressure Liquid Strainers 11990 Specifications Connection Type Swivel Ordering No. Connection Thread Sizes (NPT/BSPT or NPS) Female x Female Male x Male Male x Female Approx. Overall Length (mm) 11990-7 1/4" (F) NPT/BSPT 1/4" (F) NPT/BSPT 52 11990-10 1/4" (F) NPT/BSPT 1/4" (F) NPS 51 11990-14 3/8" (F) NPT/BSPT 3/8" (F) NPT/BSPT 51 11990-17 1/2" (F) NPT/BSPT 1/2" (F) NPT/BSPT 59 11990-20 3/8" (F) NPT/BSPT 1/4" (F) NPS 44 11990-8 1/4" (M) NPT/BSPT 1/4" (M) NPT/BSPT 57 11990-13 1/4" (M) NPT/BSPT 1/4" (M) NPS 57 11990-15 3/8" (M) NPT/BSPT 3/8" (M) NPT/BSPT 59 11990-18 1/2" (M) NPT/BSPT 1/2" (M) NPT/BSPT 70 11990-6 1/4" (M) NPS 1/4" (F) NPS 52 11990-9 1/4" (M) NPT/BSPT 1/4" (F) NPT/BSPT 56 11990-12 1/4" (M) NPT/BSPT 1/4" (F) NPS 54 11990-16 3/8" (M) NPT/BSPT 3/8" (F) NPT/BSPT 57 11990-19 1/2" (M) NPT/BSPT 1/2" (F) NPT/BSPT 67 11990-21 3/8" (M) NPT/BSPT 1/4" (F) NPS 51 Connection Type Female x Hose Shank Male x Hose Shank Swivel Ordering No. Thread Sizes (NPT/BSPT or NPS) Connections Shank Dia. (mm) Approx. Overall Length (mm) For Hose ID (mm) 11990-60 1/4" (F) NPS 7.1 67 6 11990-61 1/4" (F) NPS 10.3 70 10 11990-62 1/4" (M) NPT/BSPT 7.1 59 6 11990-63 1/4" (M) NPS 7.1 60 6 11990-64 1/4" (M) NPT/BSPT 10.3 63 10 11990-65 1/4" (M) NPS 10.3 64 10 GunJet spray gun used to remove sand particles from casting molds. H20