NMU DIECT MOUNT PNEUMTIC CTUTO VLVES I VLVES FO INDUSTY SINCE 1949 BULLETIN NMce-2004 SOLENOID CTUTION 1/4 NPT or G1/4 DIECT MOUNT TO MNY DIFFEENT CTUTOS 10 YE WNTY C5 Series: E5 Series: 3-way or 4-way, 2 or 3 position Pneumatic Service to 115 psi (8 bar) ISO 9001 CETIFIED 3 way, 2 position Pneumatic Service to 150 psi (10.3 bar) C316 Series: Stainless Steel 3 way or 4 way, 2 position Pneumatic Service 15 to 150 psi (1 to 10.3 bar) www.versa-valves.com e-mail: sales@versa-valves.com Versa Products Company, Inc., 22 Spring Valley oad, Paramus, New Jersey, US 07652 TEL: 201/843-2400 FX: 201/843-2931 Versa BV., Prins Willem lexanderlaan 1429, 7312 GB peldoorn, The Netherlands TEL: +01131-55-3681900 FX: +01131-55-3681909
DIECT MOUNT CTUTO VLVES LUMINUM CONSTUCTION SEIES C5 NMU General Description The Versa C5 NMU mount control valve is a high flow, 5-port, solenoid/pilot valve. It is designed to mount directly to any NMU actuator, thus reducing actuator response time and cost of tubing, fittings, brackets, and labor. Many adaptor kits are available for non- NMU actuators. Consult factory for kit availability. The 5-port design allows the C5 NMU to be ordered as either 4-way (for double acting actuators) or 3-way (for spring return or fail-safe actuators). The function of this valve is field convertible utilizing no special tools, gaskets, or sealants. elocation of a port plug converts a 3-way to a 4-way, or a 4-way to a 3-way. When the 4-way valve is converted to 3-way function, the unused exhaust port becomes an actuator vent into which a filter/muffler can be installed to prevent contaminents from entering either the valve or the actuator. Single solenoid models (for 2-position control), or double solenoid models (for 2 or 3-position control) are available. ctuator positioning is possible with the use of 3-position valves since all Versa C5 NMU valves are leakfree/bubbletight. complete selection of electrical connections, area classifications, and power requirements makes the most exacting and demanding Operating Pressures and Weights FUNCTION** 4-way 5/2 & 5/3 3-way** 3/2 & 3/3 3-Way/4 Way Field Convertible Solenoid Valves Valve Type Single Solenoid/spring return (2-position) Double Solenoid/detented (2-position) Double Solenoid/spring centered (3-position) Porting Size Inlet and exhaust 1/4 NPT or G1/4 Cylinder ports O ring seal per NMU standard (For non-nmu actuators, consult factory) Installation, Filtration and Lubrication Valves have no limitations on mounting orientation. 40 to 50 micron filtration and general purpose lubricating oil ISO, STM viscosity grade 32 recommended. mbient temperature range 5 F (15 C) to 125 F (50 C). 1/4 NPT G1/4 Operating Pressure ange Pneumatic 15-115 psi (1-8 bar) 10-115 psi (0.7-8 bar) 15-115 psi (1-8 bar) specifications or applications easy to satisfy. Manual overrides (guarded-push to operate) are standard on all C5 NMU valves. Consult factory for other manual overides available as an option. Materials Valve body and plunger: anodized aluminum (for stainless steel direct mount valve, consult factory) ctuating Caps: solenoid anodized aluminum spring cap synthetic resin Valve seals: plunger and body FKM (fluorocarbon) pilot piston NB (nitrile) valve/actuator mounting O rings NB (nitrile) Pilot Piston: synthetic resin Screws: stainless steel (except valve to actuator = carbon steel) Port plug: brass Solenoid parts: sleeve, plunger & spring 304 & 430F stainless steel coils epoxy encapsulated with 3 spade terminals (std) or 2 or 3 wire lead (opt) coil cover (when applicable) option: C50 = carbon steel, painted; LB XN, LB XX, PC, PC XN, PC XX, XN, XX= carbon steel, zinc chromate plated pproximate Weights Ordinary Service 0.8 lbs. (363 gms.) 1.2 lbs. (545 gms.) 1.2 lbs. (545 gms.) Flow ates Cv = 0.75 (Kv = 11) average for all ports (48 SCFM at 100 psi; 82 Nm 3 / h at 7 bar). For actuator speed rates see page 4. Options Suffix Manual Override: none Standard on basic valves, guarded-push to operate. ll other options see page 4. C5 NMU Valve Product Number Selector Basic Valve Number* POT SIZE Cv (Kv) SINGLE SOLENOID/SPING DOUBLE SOLENOID/ DOUBLE SOLENOID/SPING CENTEED, 3 POSITION ETUN, 2 POSITION DETENT, 2 POSITION Blocked Center Exhaust Ports Open 1/4 NPT.75 (11) CGS-4232-NB1 - - (coil code) CGG-4232-NB1 - - (coil code) CXX-4233-NB1 - - (coil code) CXX-4234-NB1- - (coil code) G1/4.75 (11) CGS-4292-NB1 - - (coil code) CGG-4292-NB1 - - (coil code) CXX-4293-NB1 - - (coil code) CXX-4294-NB1 - - (coil code).75 (11) CGS-3232-NB1 - - (coil code) CGG-3232-NB1 - - (coil code) CXX-3233-NB1 - - (coil code) CXX-3234-NB1 - - (coil code).75 (11) CGS-3292-NB1 - - (coil code) CGG-3292-NB1 - - (coil code) CXX-3293-NB1 - - (coil code) CXX-3294-NB1 - - (coil code) * ll valves include O ring interface seals and #10-24 mounting screws. For #10-32 screws change NB1 to NB2. For M5 screws change NB1 to NB3. ** 3-way is the same valve as 4-way, but is provided with a relocated cylinder port plug. See note on page 4 Hazardous Service 1.1 lbs. (500 gms.) 1.8 lbs. (816 gms.) 1.8 lbs. (816 gms.) Pressure ranges may change based on solenoid option. See page 4. MPa = bar 10 For higher pressure applications, consult factory. 2 For coil code see page 4. dd suffix option here, if required.
DIECT MOUNT CTUTO VLVES General Description The Versa E5 NMU mount control valve is an inexpensive, simple and effective 3-way direct-acting solenoid valve. It is designed to mount directly to any NMU actuator thus reducing cost of tubing, fittings, brackets and labor. It is most effective on spring return or fail-safe actuators where high speed open or close is not important, but where cost is a factor. threaded actuator vent port is standard. vailable as a 3-way, 2-position, direct solenoid, spring return only, and with most of the Versa solenoid options. See page 4. Operating Pressures and Weights Porting Size Inlet and Vent -1/4 NPT or G1/4 Exhaust -#10-32 (1/8 NPT or G1/8 available) Cylinder ports -O ring seal for NMU standard (For non-nmu actuators, consult factory) Flow ates Valve Type Single Solenoid/spring return (2-position) Cv = 0.08 (Kv = 1.2) average for all ports (5 SCFM at 100 psi; 8.5 Nm 3 / h at 7 bar). For actuator speed rates see page 4. Options See page 4. FUNCTION POT SIZE Cv (Kv) 3-way 3/2 1/4 NPT G1/4 SEIES E5 NMU 3-Way Solenoid Valves.08 (1.2).08 (1.2) Operating Pressure ange Pneumatic 0-150 psi (0-10.3 bar) Materials Valve body: anodized aluminum Valve seals: body/plunger NB (nitrile) valve/actuator mounting O rings NB (nitrile) Screws: (valve to actuator) = carbon steel Solenoid parts: sleeve, plunger & spring 304 & 430F stainless steel coils epoxy encapsulated with 3 spade terminals (std) or 2 or 3 wire lead (opt) coil cover (when applicable) option: C50 = carbon steel, painted; LB XN, LB XX, PC, PC XN, PC XX, XN, XX= carbon steel, zinc chromate plated pproximate Weights Ordinary Hazardous Service Service 0.6 lbs. (272 gms.) E5 NMU Valve Product Number Selector 0.9 lbs. (408 gms.) Installation, Filtration and Lubrication Valves have no limitations on mounting orientation. 40 to 50 micron filtration and general purpose lubricating oil ISO, STM viscosity grade 32 recommended. mbient temperature range 5 F (15 C) to 125 F (50 C). Basic Valve Number* SINGLE SOLENOID/SPING ETUN 2-POSITION E5SM-3011-34-NB1 - - (coil code) E5SM-3071-34-NB1 - - (coil code) For coil code see page 4. dd suffix option here, if required. * ll valves include O ring interface seals and #10-24 mounting screws. For #10-32 screws change NB1 to NB2. For M5 screws change NB1 to NB3. IN EX 3
Versa exercises diligence to assure that information contained in this catalog is correct, but does not accept responsibility for any errors or omissions. Versa also reserves the right to change or delete data or products at any time without prior notification. To be sure the data you require is correct, consult factory. NON- H Z D O US SEVICE H Z D O US S E VI C E DIMENSIONS NMU DIMENSIONS: INCHES (mm) Valve Type CGS CGG/CXX CTUTO CYCLE TIME IN SECONDS VOLTGES & COIL CODES** NMU OPTIONS VLVE TYPE DESCIPTION NOMINL COIL SUFFIX DETIL* C5 E5 POWE Spade Terminals (standard) None Strain elief mini-din type connector, cord grip PG9 -HC C=8.5 W 1/2 NPT conduit mini-din type connector -HCC 24V60 (024) 12VDC (D012) DC=10.5 W 1/2 NPT conduit, watertight, NEM 4-228L 110V50 (E110) 120V60 (120) 24VDC (D024) 220V50 (E220) 240V60 (240) 48VDC (D048) 1/2 NPT conduit, general purpose, NEM 1,2,3 -C50 240V50 (E240) C=6 W 1/2 NPT conduit, watertight, NEM 4 & 4X -PC DC=7 W Hazardous Locations, 1/2 NPT conduit, NEM 7 & 9, UL listed, CS approved -watertight, dusttight, NEM 4, 4X, 7 & 9, UL listed, CS approved Flameproof, M20x1.5 conduit, Zone 1 & 2 TEX, IP66 -XX -PC-XX -XN 24V60 (024) 12VDC (D012) 110V50 (E110), 120V60 (120) 24VDC (D024) 220V50 (E220), 240V60 (240) 48VDC (D048) 240V50 (E240) C=5.6 W DC=7.2 W Hazardous Locations, low power, 1/2 NPT conduit, 12V60 (012) 6VDC (D006) C or DC NEM 7 & 9, UL listed, CS approved -LB-XX 24V60 (024) 12VDC (D012) =1.8 W Flameproof, low power, M20x1.5 conduit, 48V60 (048) 24VDC (D024) Zone 1 & 2 TEX, IP66 -LB-XN 120V60 (120) 48VDC (D048) 240V60 (240) 120VDC (D120) Hazardous Locations, strain relief mini-din type connector, cord grip PG 9 -HC-XISC 24VDC (D024) not DC=1.6 W max 1/2 NPT conduit entry, -HCC-XISC system voltage available Factory Mutual/CS approved Standard, -228L B C 3.71 1.31.885 (94.2) (33.3) (22.5) 4.21 3.71.885 (106.9) (94.2) (22.5) Valve Type C5 E5 SEIES C5 NMU & SEIES E5 NMU 5 (82).32.46 10 (164).36.64-027, -043 B C 3.45 (87.6) 1.31 (33.3).875 (22.2) 3.96 3.45.875 (100.6) (87.6) (22.2) 25 (410).47 1.1 C5 Solenoid Option -C50, -PC B C 3.71 1.31 1.04 (94.2) (33.3) (26.4) 4.21 3.71 1.04 (106.9) (94.2) (26.4) CTUTO VOLUME in 3 (cm 3 ) 50 (820) 100 (1640) 150 (2460) 200 (3280).63 2.0.98 3.9 1.3 5.7 1.7 7.5 -XX, -XN B C 3.79 (96.3) 1.31 (33.3) 1.45 (36.8) 4.29 3.79 1.45 (109.0) (96.3) (36.8) 400 (6560) 3.1 -- 600 (9840) 4.5 -- 3.53 (89.7) 4.03 (102.4) 1000 (16400) The above chart represents approximate actuator operation times under average load conditions at 80 psi (5.5 bar). Due to differing designs of quarter-turn actuators, breakaway friction, loading, internal airflow, inlet piping, fittings and exhaust port options, the values shown are intended as an estimate. Faster or slower times may actually be achieved. 7.2 -- -XISP B 1.31 (33.3) 3.53 (89.7) C 1.15 (29.2) 1.15 (29.2) E5 * dd option number to basic valve number as suffix. ** dd coil code# to end of valve number. For other options, voltages, or Versa s Direct Mount NMU Subplate for 1/4 brass V Series, please consult factory. NMU DIMENSIONS: INCHES (mm) Solenoid Option ValveType STNDD, -228L -C50, -PC -XX, -XN Solenoid B B B.44 2.31.52 2.31.73 2.39 E5 (11.2) (58.7) (13.2) (58.7) (18.4) (60.7) For double-acting actuators (open & close), use volumes from selected actuator specifications and the chart for estimated speed. The times indicated are per shift. For spring return actuators, use open volume to obtain time from chart. ctuator spring loading may affect shift time. Slower speeds (adjustable) can always be accomplished by using Versa s Bleed Control Valves in the control valve exhaust port. 4
DIECT MOUNT CTUTO VLVES General Description The Versa C316 Series stainless steel NMU mount actuator control valve is a high flow, bubbletight, 5-port solenoid valve. It is designed to mount directly to any NMU actuator, thus reducing actuator response time and space. Installed costs are also lower as the need for tubing, fittings, brackets and assembly labor are greatly reduced. ll mounting screws and seals are included with the valve. The 5-port design allows the C316 NMU valve to be ordered as either a 4-way for double acting actuators, or as a 3-way for spring return actuators. When the 3-way function is utilized, the unused exhaust port becomes an actuator vent where a filter/muffler can be installed to prevent contaminents from entering either the valve or the actuator. The 5-port design allows the user to independently control actuator speed in either open or close direction by utilizing speed or bleed controls. Single or double solenoid 2-position models are available. Single solenoid spring return models utilize an air assisted spring return feature, assuring a positive return. Double solenoid valves may be used in applications where a momentary signal is required or in a "fail in last shifted position" actuator application. Double solenoid models are equipped with a detent that maintains the valve in the last shifted position, even in high vibration applications. ll solenoid actuators are solenoid/pilot type, which allows the use of smaller solenoids resulting in lower power consumption. This design assures a positive shift when the valve is energized and reduces the chance of coil burnout. Manual override for single or double solenoid valves is available as an option. Materials Valve body, actuating caps & internal parts: 316L stainless steel Valve seals: FKM (fluorocarbon) Screws: stainless steel Solenoid parts: 304, 430F & 302 stainless steel internal parts; coil/solenoid housing per solenoid option selected Operating Pressure and Weights SEIES C316 NMU Stainless Steel 3 or 4 Way Solenoid Valves Porting Size Inlet and Exhaust: 1/4 NPT Cylinder ports: O ring mount per NMU standard Flow ate Cv = 1.6 (Kv = 23.5) Valve *Operating pproximate Weights Type Pressure ange General Hazardous Service Pneumatic Service (-XX, -XN, -XIS_ ) (-XM_, -XIF_ ) Single Solenoid- Spring return 25 to 150 psi (1.8 to 10.3 bar) 1.3lbs (590 gms) 1.6 lbs (725 gms) 2.5 lbs (1130 gms) Double Solenoid 15 to 150 psi (1 to 10.3 bar) 1.9lbs (860 gms) 2.6 lbs (1180 gms) 4.3 lbs (1950 gms) * For applications above 125 psi (8.6 bar) exhaust flow controls or mufflers are recommended. FUNCTION 4-way 5/2 3-way 3/2 Installation, Filtration and Lubrication Valves have no limitation on mounting orientation. 40 to 50 micron filtration is recommended Lubrication not required. mbient and media temperature range -5 F to 200 F (-20 to 93 C) Options See page 6 C316 NMU Valve Product Number Selector SINGLE SOLENOID/SPING ETUN, 2 POSITION CGS-4332-316 NE1- -(coil code) CGS-3331-316 NE1- -(coil code) Basic Valve Number* 5 DOUBLE SOLENOID DETENT, 2 POSITION CGG-4332-316 NE1- -(coil code) CGG-3331-316 NE1- -(coil code) *ll valves include O ring interface seals and #10-24 mounting screws. For #10-32 screws change NE1 to NE2. For M5 screws change NE1 to NE3. dd suffix option here if required. See coil code page 6.
Voltages (Coil Codes) NOMINL Suffix Solenoid Housing ll options available in all voltages, COIL Detail Material except where noted. Consult factory for POWE other voltages. C/DC (watts) G General Purpose E 1/2" NPT conduit, NEM 1,2 & 3* None Carbon Steel, Painted 6.0/7.0 N 1/2" NPT conduit, watertight, NEM 4 & 4X* -PC Carbon Steel, Chromate coated 6.0/7.0 E Cord grip PG9 mini-din type connector, NEM 4 -HC Engineered polymer 6.5/10.5 1/2" NPT conduit mini-din type connector, NEM 4 -HCC Engineered polymer 6.5/10.5 L * For high temperature coil include, -HT Hazardous Locations- UL/CS (NEM 7 & 9) Class I, Div 2 ( & B); Class I, Div 1 (C & D); Class II, Div 1 (E, F & G)* 1/2 NPT conduit entry, Basic standard -XX Carbon Steel, Chromate coated 5.6/7.2 with Low power 1.8W coil -LB-XX Carbon Steel, Chromate coated 1.8/1.8 with Potted coil -PC-XX Carbon Steel, Chromate coated 5.6/7.2 with Stainless steel coil housing -ST-XX Stainless steel 5.6/7.2 H Flameproof (d)- TEX Zones 1 & 2, (IIB + H 2 ) Category 2G; T4* M20 x 1.5 conduit entry, Basic standard -XN Carbon Steel, Chromate coated 12VDC (D012) 24VDC (D024) 5.6/7.2 with Low power 1.8W coil, T6 -LB-XN Carbon Steel, Chromate coated 48VDC (D048) 1.8/1.8 Z with Potted coil -PC-XN Carbon Steel, Chromate coated 120V60 (120) 110V50 (E110) 5.6/7.2 with Stainless steel coil housing -ST-XN Stainless steel 220V50 (E220) 240V60 (240) 5.6/7.2 D Zones 1 & 2, (IIC) Category 2G O with M20 x 1.5 conduit entry -XDS Stainless Steel w/junction Box 10.0/4.0-10.0 U with 1/2 NPT conduit entry -XDT Stainless Steel w/junction Box 10.0/4.0-10.0 S Encapsulated (m), Increased Safety (e)- TEX L Zones 1 & 2, (II) Category 2G O with M20 x 1.5 conduit entry -XM Engineered polymer na/4.0 C with 6-12mm ø cable gland -XMF Engineered polymer NOTES na/4.0 with 1/2 NPT conduit entry -XMF Engineered polymer * For high temperature coil add, -HT na/4.0 T with 9-16mm ø cable gland -XMFF Engineered polymer na/4.0 I (included in XM_, XIF_) O Hazardous Locations- FM/CS ** 24 Volt DC only N Class I, (Group, B, C, D); Class II, (Group E, F, G), Class III, Div 1 ** with PG9 cable gland, mini-din connector -HC-XISC Engineered polymer Contact factory for other options in the na/1.6 with 1/2 NPT conduit entry -HCC-XISC Engineered polymer series na/1.6 Intrinsic Safe (ia)- TEX Zones 0, 1 & 2, (IIC) Category 1G, T6 ** with PG9 cable gland, mini-din type connector -HC-XISX6 Engineered polymer na/1.6 with 1/2 NPT conduit entry -HCC-XISX6 Engineered polymer na/1.6 Intrinsic Safe (ib)- TEX Zones 1 & 2, (IIB) Category 1G with M20 x 1.5 conduit entry -XIF Engineered polymer na/0.8 with 1/2 NPT conduit entry -XIFF Engineered polymer na/0.8 M I Manual Override, un-guarded push and hold (Not available with all solenoid options.) -ME N/ S Solenoid exhaust adapter, 1/8" NPT -H2 N/ C Dimensions SEIES 316 NMU DIMENSIONS SOLENOID OPTIONS GENEL SEVICE HZDOUS SEVICE HZDOUS SEVICE Valve Type (-XX, -XN, -XISP) (-XM, -XIF) B C B C B C Single solenoid, spring return Inches 5.62 1.44 2.33 5.67 1.44 2.33 6.59 2.56 4.27 3-Way or 4-Way (mm) (142.7) (36.6) (59.1) (144) (36.6) (59.1) (167.3) (65) (108.5) Double solenoid Inches 8.70 1.44 2.33 8.79 1.44 2.33 10.6 2.56 4.27 3-Way or 4-Way (mm) (221) (36.6) (59.1) (233.2) (106.9) (59.1) (269.2) (65) (108.5) For warranty information and/or any additional information with regards to installation, operation and service warnings, please consult factory. Versa Products Company, Inc., 22 Spring Valley oad, Paramus, New Jersey, US 07652 TEL: 201/843-2400 FX: 201/843-2931 Versa BV., Prins Willem lexanderlaan 1429, 7312 GB peldoorn, 6The Netherlands TEL: +01131-55-3681900 FX: +01131-55-3681909 6 www.versavalves.com