Handle: 6" JTC-1147 6" CHAIN WRENCH Chain: 18" (400mm) Handle: 20" Chain: 25" JTC-1149 20" CHAIN WRENCH JTC-1150 12" STRAP WRENCH Handle: 12" Strap length: 36"
JTC-1355 EUROPEAN DOOR HINGE / HANDLE KIT For removing rear door hinge and handle o T30 x 250mmL BENZ 220C and NEW S. o T20 x 210mmL VW and BENZ o Bits M4, M8, M10, T40, T45 x 25mm 1998 & newer VW golf, Jetta, Passat & new Bettle o Ratchet Handle x 240mm JTC-1728 ANGLE TIP LOCK RING PLIERS Spread snap lock rings on brakes, transmissions, pedal shafts, clutch shafts & machine tools. Jaws have deep serrations on the outside of tip to help lock rings securely. Spreading: 3.5 ~ 28mm Total length: 225mm JTC-3002 36" JUMBO PRY BAR Chrome-molybdenum steel. Go-through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Flat tip.
JTC-3003 36" JUMBO PRY BAR (BEND) Chrome molybdenum steel. Go through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. Curved tip. JTC-3024 T TYPE SCREWDRIVER Size: 3 x 8m/m Full length: 250mm JTC-3117 4 PCS PRY BAR SET Spec: o 7/16" x 24"L o 7/16" x 18"L o 3/8" x 12"L o 1/4" x 8"L
JTC-3207 IMPACT DRIVER SET Bits Material: S2 o 4 Bits x 36mml: PHILLIPS NO. 2, NO. 3 SLOTTED θ8m, 10mm o 28 Bits x 80mml: PHILLIPS NO. 2, NO. 3 JTC-3311 90 DEGREE EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 90 BEND Length: 11" JTC-3312 EXTRA LONG ROUND JAWS PLIER Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 8mm (5/16") Length: 11"
JTC-3313 EXTRA LONG ROUND JAWS PLIER Made from CR-MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 13mm (1/2") Length: 11" JTC-3314 EXTRA LONG ROUND JAWS PLIER Made from CR MO material. Suitable for using on hoses, spark plug wires, etc. Ø: 19mm (3/4") Length: 11" JTC-3471 10 1/2" SNAP RING PLIERS SET Featured replaceable tips and have a spring ratchet locking mechanism to hold circlip securely against tension. Offset tips make it easier to facilitate circlip. o 2 of each 2.75mm tips in o, 15, 45, 90. o 2 of each 3.0mm tips in o, 15, 45, 90. Length: 10 1/2" (265mm) Spread: o Internal: 60mm ~ 100mm o External: 38mm ~ 85mm
JTC-3501 8 PCS FOLDING HEX SET Convenient folding type for easy and high torque application. Made from chrome vanadium steel and heat treated. 2.5, 3, 4, 5, 6, 7, 8, and 10mm. JTC-3502 8 PCS FOLDING STAR SET Convenient folding type for easy and torque application. Made from chrome vanadium steel and heat treated. T9, 10, 15, 20, 25, 27, 30 and 40. JTC-3503 8 PCS FOLDING STAR SET (TAMPER PROOF) Convenient folding type for easy and high torque application. Special design with hole in the head to fit the special screws. Made from chrome vanadium steel and heat treated. T9H, 10H, 15H, 20H, 25H, 27H, 30H and T40H.
JTC-3504 9 PCS LONG HEX SET Plastic holder professionally designed for nice installation and convenience usage. Extra long arm series can save strength and time enables good operation. Material: S2 1.5, 2, 2.5, 3, 4, 5, 6, 8, and 10mm JTC-3505 9 PCS LONG BALL POINT HEX SET Works in hard to reach areas. Faster inserting and removing. Full depth engagement. Material: S2 1.5, 2, 2.5, 3, 4, 5, 6, 8, and 10mm Special offer for CR V material JTC 3508A JTC-3506 9 PCS LONG BALL POINT HEX SET Works in hard to reach areas. Faster inserting and removing. Full depth engagement. Material: S2 1/16", 5/64", 3/32", 1/8", 5/32", 3/16", 1/4", 5/16", and 3/8".
JTC-3509 58 PCS POWER BIT SET Material: S2 o 9 pcs 30mmL star power bit: T20, T25, T27, T30, T40, T45, T50, T55, and T60. o 9 pcs 75mmL star power bit: T20, T25, T27, T30, T40, T45, T50, T55, and T60. o 9 pcs 30mmL hex power bit: 4, 5, 6, 7, 8, 10, 12, 14, and 17. o 9 pcs 75mmL hex power bit: 4, 5, 6, 7, 8, 9, 10, 12, and 3/8". o 5 pcs 30mmL spline power bit: M5, M6, M8, M10, and M12. o 8 pcs 75mmL spline power bit: M5, M6, M8, M9, M10, M12, M14, and M16H. o 5 pcs 75mmL ribe power bit: RM6, RM7, RM8, RM10, and RM12. o 2 pcs 75mmL square power bit: 8 and 10. o 1 pc 10mm (hex) x 3/8" Dr. Adapter o 1 pc 10mm (hex) x 1/2" Dr. Adapter JTC-3629 90 DEGREE EXTRA LONG NEEDLE NOSE PLIERS Go through alloy steel square. Rugged firm grip designed plastic handle. Excellent for prying engine, cylinder head, transmission cases, manifold and drive line components. JTC-3701 90 DEGREE ANGLE SCREWDRIVER SET Perfect for fastening jobs in confined areas. Features a quick set handle holding in all angle for efficient performance and 1/4" hex shank can be used with power driver or by included hand driver. #1 & #2 25m/m bit included.
JTC-3704 SELF ADJUST PLIERS The gripping span remains substantially constant for any size workpiece. Jaws always grip in parallel position up to 1 3/8" (35mm). Uniform, powerful grip. Self adjusts to workpiece size. Super strong, laminated heat treated steel construction. JTC-3705 SELF ADJUST PLIERS The gripping span remains substantially constant for any size workpiece. Jaws always grip in parallel position up to 2" (50mm). Uniform, powerful grip. Self adjusts to workpiece size. Super strong, laminated heat treated steel construction. JTC-3819 EXTRA LONG NEEDLE NOSE PLIERS Made from CR MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws, and flash riveted joints enable pliers to reach into recessed areas. Spec: 0 STRAIGHT Length: 11"
JTC-3820 EXTRA LONG NEEDLE NOSE PLIERS Made from CR-MO material to provide a high strength level and uniform hardness. The design of pliers means reach and application advantage at every turn. Long, slim jaws and flash-riveted joints enable pliers to reach into recessed areas. Spec: 45 BEND Length: 11" JTC-3924 9 IN 1 STAR KEY SET (TAMPER PROOF) Made from SNCM8660 material. Long shank to reach confined areas or increase torque. With double end tamper resist. T10H, 15H, 20H, 25H, 27H, 30H, 40H, 45H, and 50H. JTC-3925 9 PCS STAR SCREWDRIVER SET (TAMPER PROOF) Chrome molybdenum steel with heat treated blade & magnetic tip. Special design with hole in the head to fit the special screws. o T8H x 100mm, T9H x 100mm, T10H x 100mm, T15H x 125mm, T20H x 125mm, T25H x 125mm, T27H x 150mm, T30H x 150mm, and T40H x 150mm.
Material: S2 JTC-3933 42 PCS POWER BIT SET o 8 pcs 30mm star power bit: T20, T25, T27, T30, T40, T45, T50, and T55. o 8 pcs 75mm star power bit: T20, T25, T27, T30, T40, T45, T50, and T55. o 7 pcs 30mm hex power bit: 4, 5, 6, 7, 8, 10, and 12mm. o 7 pcs 75mm hex power bit: 4, 5, 6, 7, 8, 10, and 12mm. o 5 pcs 30mm spline power bit: M5, M6, M8, M10, and M12. o 5 pcs 75mm spline power bit: M5, M6, M8, M10, and M12. o 1 pc 10mm (hex) x 3/8" Dr. Adapter o 1 pc 10mm (hex) x 1/2" Dr. Adapter JTC-4066 LARGE LOCKING RING PLIERS Applicable: Large rings on drive shafts in earth movers and construction vehicles. Tip form: interchange, wide, and milled. Tip size (mm): 3.5 x 8mm; spreading 8 75mm Total length: 330mm JTC-4093 S TYPE WRENCH (12mm) Special S angle designed for better operation. Use for installing and removing the door hinge screws. Size: 12mm; 12PT Applicable: TOYOTA, NISSAN, HONDA, MITSUBISH, SUZUKI, etc.
JTC-4754 DOOR HINGE BOLTS REMOVER KIT Special angle wrench design to quickly and easily loosen and tighten the bolts in door hinges. Adjusts the toe on the rear axle. o 7 pcs bits: M8, M10, M12, T30, T40, T45, and T50. o 1 pc special angle 3/8" Dr. wrench o 1 pc 45 8mm gear wrench Applicable: VW, AUDI, BENZ, etc. JTC-5056 PARROT TYPE LOCKING PLIERS The jaws made of CR MO, and bodily heat treated. Total length: 215mm Capacity: φ5 ~ φ40mm JTC-5057 ADJUSTABLE HOSE PINCH OFF LOCKING PLIERS The jaws made of CR MO, and bodily heat treated. Total length: 280mm Nose length: 120mm
JTC-5350 11 PCS SHORT HEX KEY SET Size: 1.5, 2, 2.5, 3, 4, 5, 6, 7, 8, 10, and 12mm. Material: S2, sanding chrome finished surface. Length: short type JTC-5351 7 PCS LONG HEX KEY SET Size: 2.5, 3, 4, 5, 6, 8, and 10 mm. Material: S2 sanding chrome finished surface. Length: extra long type JTC-5357 8 PCS L HOLDER STAR BIT SET o 7 pcs bits: T10, T15, T20, T25, T27, T30, and T40. o 1 pc: 2 way L type bit holder wrench. Bit material: S2, silver plated. Size: 1/4" x 30mmL
JTC-5358 8 PCS L HOLDER STAR BIT SET (TAMPER PROOF) o 7 pcs bits: T10H, T15H, T20H, T25H, T27H, T30H, and T40H. o Bit material: S2, silver plated. Size: 1/4" x 30mmL JTC-5359 8 PCS L HOLDER HEX BIT SET o 7 pcs bits: H2, H3, H4, H5, H6, H7, and H8. o 1 pc: 2 way L type bit holder wrench. Bit material: S2, silver plated. Size: 1/4" x 30mmL JTC-5360 8 PCS L HOLDER BIT SET o 7 pcs bits: PH1, PH2, PH3, PZ1, PZ2, SL4, and SL7. o 1 pc: 2 way L type bit holder wrench. Bit material: S2, silver plated. Size: 1/4" x 30mmL
JTC-5361 10 PCS STAR BIT SET o 10 pcs bits: T7, T8, T9, T10, T15, T20, T25, T27, T30, T40. Material: S2 Size: 1/4" x 25mmL JTC-5362 10 PCS 5 PT STAR BIT SET (TAMPER PROOF) o 10 pcs bits: TS08, TS10, TS15, TS20, TS25, TS27, TS30, TS40, TS45, TS50. Material: S2 Size: 1/4" x 25mmL JTC-5363 10 PCS STAR BIT SET (TAMPER PROOF) o 10 pcs bits: T7H, T8H, T9H, T10H, T15H, T20H, T25H, T27H, T30H, T40H. Material: S2 Size: 1/4" x 25mmL
JTC-5364 33 PCS COMPRHENSIVE BIT SET (TAMPER PROOF) o 9 pcs star bits (tamper proof): T8H, T10H, T15H, T20H, T25H, T27H, T30H, T35H, and T40H. o 12 pcs hex bits (tamper proof): 2, 2.5, 3, 4, 5, and 6mm. 5/64", 3/32", 7/64", 1/8", 9/64", 5/32" SEA o 3 pcs torque set bits: 6, 8, and 10. o 4 pcs tri wing bits: 1, 2, 3, and 4. o 4 pcs spanner bits: 4, 6, 8, and 10. o 1 pc magnetic bit holder (60 mml) o Bit size: 1/4" x 25mmL JTC-5365 6 PCS SPLINE BIT SET (30L) o 5 pcs 10mm spline bits x 30L: M5, M6, M8, M10, M12. o 1 pc 1/2" DR. x 10mm bit holder. Bit material: S2. JTC-5366 7 PCS STAR BIT SET (30L) o 6 pcs 10mm star bits x 30L: T25, T30, T40, T45, T50, T55 o 1 pc 1/2" DR. x 10mm bit holder. Bit material: S2.
JTC-5405 COMFORT GRIP LOCKING PLIERS Made from CR MO. Length: 250mm; setting switch covered with TPR material. Designed for easy holding and releasing, save more time and energy. JTC-5610 55 PCS MINI RATCHET BITS SET Bit material: S2 Length: 20mm Ratchet length: 20mm o 1 pc mini ratchet o 1 pc ratchet screwdriver o 1 pc magnet extension bar o 11 pc STAR T6, T7, T8, T9, T10, T15, T20, T25, T27, T30, and T40. o 11 pc STAR (tamper proof) o 6 pc HEX H2, H2.5, H3, H4, H5, and H6. o 8 pc 5 PT. STAR (tamper proof) TS8H, TS10H, TS15H, TS20H, TS25H, TS27H, TS30H, and TS40H. o 4 pc slotted FD3, FD4, FD5, FD6, and FD7. o 4 pc Y type 1, 2, 3, and 4. o 4 pc X type 6, 8, 10 JTC-5623 16" SNAP RING PLIERS SET Replaceable tips and spring ratchet locking mechanism to hold against snap ring tension. o One internal snap ring plier, and one external snap ring plier. o 3mm tips: straight, 45, and 90. Capacity: 85 ~ 170mm
JTC-5624 20" SNAP RING PLIERS SET Replaceable tips and spring ratchet locking mechanism to hold against snap ring tension. One internal snap ring plier and one external snap ring plier. 3.5mm tips: 90 x 2 sets Bolt, nut and washers x 4 sets Capacity: 165 ~ 300mm JTC-5709 EXTRA LONG RETAINING RING PLIER (INTERNAL STRAIGHT) Length: 255mm Tip length: 75mm Tip diameter: Ø 1.2mm JTC-5710 EXTRA LONG RETAINING RING PLIER (INTERNAL BENT) Length: 255mm Bent tip length: 65mm Tip diameter: Ø 1.2mm
JTC-5711 EXTRA LONG RETAINING RING PLIER (EXTERNAL STRAIGHT) Length: 225mm Tip length: 75mm Tip diameter: Ø 1.2mm JTC-5712 EXTRA LONG RETAINING RING PLIER (EXTERNAL BENT) Length: 225mm Bent tip length: 65mm Tip diameter: Ø 1.2mm JTC-5713 12" EXTRA LONG NEEDLE NOSE PLIER (LONG JAWS) Long jaws design for better reaching into recessed areas. Length: 12" (300mm) Jaw length: 170mm
JTC-5714 7" WIRE CUTTER Applicable: o Wire: Ø 1.5mm o Copper: Ø 4mm Length: 165mm JTC-5715 POWER RIBE BIT SET Bit material: S2 o 10 pcs 30mmL ribe power bit: RM5, 6, 7, 8, 9, 10, 11, 12, 13, and 14. o 11 pcs 100mmL ribe power bit: RM5, 6, 7, 8, 9, 10, 10.3, 11, 12, 13, and 14. o 2 pcs adapter: 10mm (hex) x 1/2" Dr. and 10mm (hex) x 3/8" Dr. JTC-5909 16" EXTRA LONG HANDLE NEEDLE NOSE PLIERS (0 ) Made from CR MO material to provide a high strength level and uniform hardness. The design of pliers mean reach and application advantage at every turn. Long, slim jaws and flash riveted enable pliers to reach into recessed areas. Spec: Straight Length: 16"
JTC-5910 16" EXTRA LONG HANDLE NEEDLE NOSE PLIERS (45 ) Made from CR MO material to provide a high strength level and uniform hardness. The design of pliers mean reach and application advantage at every turn. Long, slim jaws and flash riveted enable pliers to reach into recessed areas. Spec: 45 Bent Length: 16" JTC-193810 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 10mm JTC-19382 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 1/4"
JTC-19385 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 5mm JTC-19386 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 6mm JTC-19387 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 7mm
JTC-19388 FLEXIBLE SHAFT NUT DRIVERS Round, flexible blade, fit for hexagon headed bolts, nuts screws and hose clamp. Spec: 8mm JTC-34258 HEAVY DUTY TWIN COLOR DIAGONAL PLIERS Made from CR MO to provide a high strength level and uniform hardness. Handle material made of PP + TPR for good grip. Spec: 8" JTC-342810 WATERPUMP PLIERS 10" Made from CR V to provide a high strength level and uniform hardness. Handle material made from PVC. Spec: 10"
JTC-10WR LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat treated, welding brazed. Nickel plated. Spec: 10" Function: Includes the knife JTC-11R LOCKING "C" CLAMP CR MO drop forge jaws. Bodily heat treated. Welding brazed. Nickel plated. Spec: 11" Function: C Shaped plier JTC-18R LOCKING "C" CLAMP CR MO drop forge jaws. Bodily heat treated. Welding brazed. Nickel plated. Spec: 18" Function: C Shaped plier
JTC-20R 20" LOCKING CHAIN PLIER Chain length: 19" CR MO jaws Bodily heat treated. Nickel plated. Function: Adjustable chain use to clip things. JTC-5WR LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat treated, welding brazed. Nickel plated. Spec: 5" Function: Includes the knife JTC-6LN LONG NOSE LOCKING PLIERS Chrome moly steel drop forged jaws. Heat treated jaws. Nickel plated. Spec: 6" Includes sharp knife.
JTC-7WR LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat treated, welding brazed. Nickel plated. Spec: 7" Function: Includes the sharp knife JTC-8R 8" WELDING CLAMP Size: 8" CR MO jaws Bodily heat treated. Welding brazed. Nickel plated. Function: Clips things by the two flat pieces in front of the clamp. JTC-9LN LONG NOSE LOCKING PLIERS Chrome moly steel drop forged jaws. Bodily heat treated, welding brazed. Nickel plated. Spec: 9" Function: Includes the sharp knife
JTC-9R 9" WELDING CLAMP Size: 9" CR MO jaws Bodily heat treated. Welding brazed. Nickel plated. Function: U shaped jaws allow access and perfect visibility when welding. JTC-3210S 50 PCS GO THROUGH SCREWDRIVER SET 50 pcs The set could be hanged on the display board. ITEM SPEC ITEM SPEC 3707 1-1/2" two-way 3713 8" x 8Θ x 5PCS x 4PCS 3708 4" x 6mm x 5PCS 3709 4" x 6mmΘ x 5PCS 3710 6" x 8mm x 5PCS 3711 6" x 8mmΘ x 5PCS 3210 12" x 10Θ x 4PCS 3804 101 3 x 3"Θ x 6PCS 3808 102 5 x 12"Θ x 6PCS 3811 107 6 x 12" x 5PCS JTC-3470S 44 PCS HEAVY DUTY SCRREWDRIVER SET 44 pcs The set could be hanged on the display board. ITEM SPEC ITEM SPEC 3463 3.0 x 75Θ x 3467 6.5 x 100Θ x 6PCS 8PCS 3464 #0 x 75 x 6PCS 3465 6.5 x 38Θ x 4PCS 3766 #2 x 38 x 4PCS 3468 #2 x 100 x 8PCS 3469 8.0 x 150Θ x 4PCS 3470 #3 x 150 x 4PCS
JTC-HB175 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: Internal 90 Length: 175 JTC-HB230 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: Internal 90 Length: 230 JTC-HB300 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: Internal 90 Length: 300
JTC-HS175 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: Internal straight Length: 175 JTC-HS230 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: Internal straight Length: 230 JTC-HS300 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: Internal straight Length: 300
JTC-K5044 4 PCS HEAVY DUTY SNAP RING PLIERS SET Item: 5401 ~ 5404 o 1 pc Heavy Duty Internal straight o 1 pc Heavy Duty Internal 90 o 1 pc Heavy Duty External straight o 1 pc Heavy Duty External 90 JTC-SB175 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: External 90 Length: 175 JTC-SB230 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: External 90 Length: 230
JTC-SB300 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: External 90 Length: 300 JTC-SS175 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: External straight Length: 175 JTC-SS230 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: External straight Length: 230
JTC-SS300 RETAINING RING PLIERS Made from CR V to provide a high strength level and uniform hardness. Spec: External straight Length: 300 JTC-U11MC 11 PC MINI RATCHET BIT SET T10H, T15H, T20H, T25H, T27H, T30H, and T40H. #1 and #2 6 mm