Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-CH8-EN AVAILABLE FOR : ADS-AL CA Rev. Date: April 8, 06 Doc. No.: ##848## U.S. PATENT NO. 8,856,780 CH8 The brand names and logos found in this guide are property of their respective owners. NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 INSTALL TYPE SELECTION FEATURES MAKE MODEL NOTE I WARNING: All vehicle doors must be closed and locked prior to remote start sequence. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT TACHOMETER OUTPUT SECURE TAKEOVER GLOW PLUGS STATUS RAP SHUTDOWN CTRL DODGE RAM Dart Tip-Start AT & MT (without Autolight) 3-6 Dart Tip-Start AT & MT (with Autolight) 3-6 500 Tip-Start AT 3-6 3 500 Diesel Tip-Start AT 4-6 4 500 / 3500 Tip-Start AT 3-6 3 500 / 3500 Diesel Tip-Start AT 3-6 4
Page 3 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE - CROSS REFERENCE CHART - OF MAKE MODEL YEAR DESCRIPTION DODGE NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Dart Tip-Start AT & MT (without Autolight) 3-6 V ~ White 06 pin 06 Red (+) Ignition connector F Ground ~ White 06 pin 03 Black (-) Ignition connector F Ignition ~ White 06 pin 04 Purple/Brown (+) Ignition connector F Imo Lin ~ White 06 pin 05 White/Green (DATA) Ignition connector F CanH ~ Black 6 pin 06 Gray/White (DATA) OBDII connector ~ CanL ~ Black 6 pin 4 Yellow (DATA) OBDII connector ~ Parking Light ~ Black 06 pin 03 White/Brown (MUX) Parking light switch A Rap Shutdown ~ ~ ~ ~ Purple (-) Driver kick panel harness B Clutch ~ Black 03 pin 0 LtGreen/Yellow (-) Clutch switch ~ Clutch Interruption ~ Black 03 pin 0 Black (-) Clutch switch ~
Page 4 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE - WIRING DIAGRAM - OF PARKING LIGHT SWITCH 6 5 4 3 PARKING LIGHT (MUX) CONNECTIONS REQUIRED ONLY WITH MANUAL TRANSMISSION CLUTCH SWITCH IGNITION NODE WHITE CLUTCH INTERRUPTION (-) 3 CLUTCH (-) 85 87A 87 86 6 5 4 3 IMO LIN IGNITION (+) 000Ω 30 85 87A 87 86 30 REMOTE STARTER PARKING LIGHT (+) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK RELEASE (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND WHEN RUNNING (-) OUTPUT STARTER (-) OUTPUT INPUT INPUT IGNITION (+) OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - - RED LOCK/ARM (-) INPUT - GREEN/ UNLOCK/DISARM (-) INPUT - BLUE/ TRUNK RELEASE (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/ (NC) WHITE STARTER (+) INPUT - /WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/ - LIN CUT SIDE WHITE/RED - LIN CUT VEHICLE SIDE WHITE (NC) YELLOW/ - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/ - IMO LIN ORANGE/WHITE (NC) ORANGE (NC) PINK/ (NC) PINK - IGNITION (+) INPUT BLUE/RED - INPUT BLUE/YELLOW - HOOD STATUS (-) OUTPUT GREEN/RED - RAP SHUTDOWN (-) OUTPUT GREEN/YELLOW (NC) GRAY/RED - BRAKE STATUS (+) OUTPUT GRAY/YELLOW (NC) HARNESS RAP SHUTDOWN (-) CANH CANL 3 4 5 6 7 8 DRIVER KICK PANEL OBDII 9 0 3 4 5 6
Page 5 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE - CROSS REFERENCE CHART - OF MAKE MODEL YEAR DESCRIPTION DODGE NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Dart Tip-Start AT & MT (with Autolight) 3-6 V ~ White 06 pin 06 Red (+) Ignition connector F Ground ~ White 06 pin 03 Black (-) Ignition connector F Ignition ~ White 06 pin 04 Purple/Brown (+) Ignition connector F Imo Lin ~ White 06 pin 05 White/Green (DATA) Ignition connector F CanH ~ Black 6 pin 06 Gray/White (DATA) OBDII connector ~ CanL ~ Black 6 pin 4 Yellow (DATA) OBDII connector ~ Parking Light ~ Black 06 pin 03 White/Brown (MUX) Parking light switch A Rap Shutdown ~ ~ ~ ~ Purple (-) Driver kick panel harness B Autolight Off ~ Black 06 pin 06 White/Yellow (MUX) Parking light switch A Clutch ~ Black 03 pin 0 LtGreen/Yellow (-) Clutch switch ~ Clutch Interruption ~ Black 03 pin 0 Black (-) Clutch switch ~
Page 6 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE - WIRING DIAGRAM - OF PARKING LIGHT SWITCH 6 5 4 3 LIGHT OFF (MUX) LIGHT ON (MUX) CONNECTIONS REQUIRED ONLY WITH MANUAL TRANSMISSION CLUTCH SWITCH IGNITION NODE WHITE CLUTCH INTERRUPTION (-) 3 CLUTCH (-) 85 87A 87 86 6 5 4 3 IMO LIN IGNITION (+) 000Ω 30 87 85 87A 30 86 REMOTE STARTER PARKING LIGHT (+) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK RELEASE (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND WHEN RUNNING (-) OUTPUT STARTER (-) OUTPUT INPUT INPUT IGNITION (+) OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - - RED LOCK/ARM (-) INPUT - GREEN/ UNLOCK/DISARM (-) INPUT - BLUE/ TRUNK RELEASE (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/ (NC) WHITE STARTER (+) INPUT - /WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/ - LIN CUT SIDE WHITE/RED - LIN CUT VEHICLE SIDE WHITE (NC) YELLOW/ - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/ - IMO LIN ORANGE/WHITE (NC) ORANGE (NC) PINK/ (NC) PINK - IGNITION (+) INPUT BLUE/RED - INPUT BLUE/YELLOW - HOOD STATUS (-) OUTPUT GREEN/RED - RAP SHUTDOWN (-) OUTPUT GREEN/YELLOW (NC) GRAY/RED - BRAKE STATUS (+) OUTPUT GRAY/YELLOW (NC) HARNESS RAP SHUTDOWN (-) CANH CANL 3 4 5 6 7 8 DRIVER KICK PANEL OBDII 9 0 3 4 5 6
Page 7 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE 3 - CROSS REFERENCE CHART - OF MAKE MODEL YEAR DESCRIPTION RAM NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR 500 500 3500 Tip-Start AT 3-6 V D664A Black 06 pin 06 Red (+) Ignition connector F Ground D664A Black 06 pin 03 Black (-) Ignition connector F Mux D664A Black 06 pin 04 Purple/Brown (+) Ignition connector F Ignition ~ Gray 04 pin 0 Pink/Green (+) Trailer pack connector, right of steering ~ Imo Lin D664A Black 06 pin 05 White/Green (DATA) Ignition connector F CanH D7405A Black 6 pin 06 Gray/White (DATA) OBDII connector ~ CanL D7405A Black 6 pin 4 Yellow (DATA) OBDII connector ~ Parking Light D4A Black 0 pin 0 White/Brown (MUX) Parking light switch A Rap Shutdown ~ ~ ~ ~ Purple (-) Driver kick panel harness B
Page 8 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE 3 - WIRING DIAGRAM - OF TRAILER PACK GRAY IGNITION (+) PARKING LIGHT SWITCH 3 4 5 PARKING LIGHT (MUX) 3 4 IGNITION NODE 6 7 8 9 0 6 5 4 3 IMO LIN MUX (+) REMOTE STARTER TACH (AC) INPUT STARTER (+) OUTPUT PARKING LIGHT (+) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND WHEN RUNNING (-) OUTPUT INPUT INPUT IGNITION (+) INPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT DIODE N400 LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - - RED LOCK/ARM (-) INPUT - GREEN/ UNLOCK/DISARM (-) INPUT - BLUE/ (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/ PARKING LIGHT (+) INPUT - WHITE STARTER (+) INPUT - /WHITE (NC) GREEN TACH (AC) OUTPUT - PURPLE/WHITE HARNESS WHITE/ - LIN CUT SIDE WHITE/RED - LIN CUT VEHICLE SIDE WHITE (NC) YELLOW/ - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - PARKING LIGHT (MUX) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/ - IMO LIN ORANGE/WHITE (NC) ORANGE - MUX (+) OUTPUT PINK/ (NC) PINK - IGNITION (+) INPUT BLUE/RED - INPUT BLUE/YELLOW - HOOD STATUS (-) OUTPUT GREEN/RED - RAP SHUTDOWN (-) OUTPUT GREEN/YELLOW (NC) GRAY/RED - BRAKE STATUS (+) OUTPUT GRAY/YELLOW (NC) RAP SHUTDOWN (-) CANH CANL 3 4 5 6 7 8 DRIVER KICK PANEL OBDII 9 0 3 4 5 6
Page 9 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE 4 - CROSS REFERENCE CHART - OF MAKE MODEL YEAR DESCRIPTION RAM NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR 500 500 3500 Diesel Tip-Start AT 3-6 V D664A Black 06 pin 06 Red (+) Ignition connector F Ground D664A Black 06 pin 03 Black (-) Ignition connector F Mux D664A Black 06 pin 04 Purple/Brown (+) Ignition connector F Ignition ~ Gray 04 pin 0 Pink/Green (+) Trailer pack connector, right of steering ~ Imo Lin D664A Black 06 pin 05 White/Green (DATA) Ignition connector F CanH D7405A Black 6 pin 06 Gray/White (DATA) OBDII connector ~ CanL D7405A Black 6 pin 4 Yellow (DATA) OBDII connector ~ Parking Light D4A Black 0 pin 0 White/Brown (MUX) Parking light switch A Rap Shutdown ~ ~ ~ ~ Purple (-) Driver kick panel harness B
Page 0 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 TYPE 4 - WIRING DIAGRAM - OF DIODE N400 TRAILER PACK GRAY IGNITION (+) PARKING LIGHT SWITCH 3 4 5 PARKING LIGHT (MUX) 3 4 IGNITION NODE 6 7 8 9 0 6 5 4 3 IMO LIN MUX (+) REMOTE STARTER TACH (AC) INPUT STARTER (+) OUTPUT PARKING LIGHT (+) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT GROUND WHEN RUNNING (-) OUTPUT INPUT INPUT IGNITION (+) INPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT GLOW PLUG (+) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - - RED LOCK/ARM (-) INPUT - GREEN/ UNLOCK/DISARM (-) INPUT - BLUE/ (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/ PARKING LIGHT (+) INPUT - WHITE STARTER (+) INPUT - /WHITE (NC) GREEN TACH (AC) OUTPUT - PURPLE/WHITE HARNESS WHITE/ - LIN CUT SIDE WHITE/RED - LIN CUT VEHICLE SIDE WHITE (NC) YELLOW/ - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - PARKING LIGHT (MUX) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/ - IMO LIN ORANGE/WHITE (NC) ORANGE - MUX (+) OUTPUT PINK/ - GLOW PLUG (+) OUTPUT PINK - IGNITION (+) INPUT BLUE/RED - INPUT BLUE/YELLOW - HOOD STATUS (-) OUTPUT GREEN/RED - RAP SHUTDOWN (-) OUTPUT GREEN/YELLOW (NC) GRAY/RED - BRAKE STATUS (+) OUTPUT GRAY/YELLOW (NC) RAP SHUTDOWN (-) CANH CANL 3 4 5 6 7 8 DRIVER KICK PANEL OBDII 9 0 3 4 5 6
Page of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (X) twice = STANDARD HARD MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure.
Page of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 MODULE PROGRAMMING PROCEDURE - WITH KLON Close driver door. OFF Turn key to OFF position. 3 Re-open driver door to wake up data bus. Press UNLOCK on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button. Wait, LED will flash GREEN once [x]. 3 ÆÆ Æ WARNING: Disconnect power last. Disconnect module from vehicle. Connect module to computer and proceed with extended programming. 4 5 ON Turn key to ON position. Wait, LED will turn solid RED. 4 Æ WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. 6 7 8 9 0 OFF ON Turn key to OFF position. Remove key. Insert key into ignition. Turn key to ON position. Wait, LED will flash GREEN. 5 6 7 8 9 OFF OFF ON START Turn key to ON position. Wait, LED will turn solid GREEN for seconds. Turn key to OFF position. Turn key to START position. Turn key to OFF position. 0 Module Programming Procedure completed.
Page 3 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ A 980 L 990 Y 000 A 00 B 98 M 99 00 B 0 C 98 N 99 00 C 0 D 983 P 993 3 003 D 03 E 984 R 994 4 004 E 04 F 985 S 995 5 005 F 05 G 986 T 996 6 006 G 06 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 K 989 X 999 9 009 K 09 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.
IMPORTANT Page 4 of 4 ADS-AL(DL)-CH8-EN Doc. No.: ##848## 06048 WARNING: READ BEFORE REMOTE NOTICESTARTING THE VEHICLE I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - TO THE VEHICLE OWNER NOTE I È All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTIºN COMING UP! Press UNLOCK on after-market remote. TIME RESTRICTIºN Within 45 SECONDS from previous step: 3! Open vehicle door. Enter vehicle. Close vehicle door. Insert key into ignition. Turn key to ON position. Press and release BRAKE pedal. Take over procedure completed. Failure to follow procedure within time restriction will result in vehicle engine shutdown.