Page 1 of 5 MOUNTING LOCATION: Upper right side of radio cavity-es300 Right sideof radio cavity-sc430&es350 Right side of climate control-solara TOOLS REQUIRED: Hook tool / Pry tool 10mm driver/ Phillips screwdriver 3/32 drill bit and drill Masking tape/ Shop towel PARTS INCLUDED: (1) S7-1570 Mount (3) 1" needle point screws [3E] (1) 1"x2.060" Protective Tape CELL PHONE & MEDIA MOUNT INSTALLATION INSTRUCTIONS PART#: 75136-200 MFG: LEXUS / TOYOTA MODELS & YEARS: This Page:LEXUS - ES300 90-2001 SC430 02-10 (See pg.2) ES350 07-11 (See pg. 4) LS460/600 2007 (See pg.5) TOYOTA-Solara-Camry 04-07 (pg.3) (Excludes 2004 Camry Sedan) * * ADVISEMENT * * Read instructions completely prior to starting installation. All InDash Mounts are designed so that after installation, phone is facing normal driver position for left-hand drive vehicles. This mount is not designed to be used in foreign countries with right-hand drive vehicles. Use extreme care when working around the plastic components on the dash. Excess force, can cause breakage of the plastic components. STEP #1 STEP #2 STEP #3 With the hook tool remove the small molding strip located between the climate control and the ashtray, by pulling strip straight out. Remove two 10mm Hex head screws that are now exposed. These screws hold the bottom of the radio and climate control. With the hook tool remove the molding that holds the air vents, clock and the emergency light switch, by pulling from each corner straight out to release four clips (one clip on each corner). Push molding up and with masking tape, molding to the dash to hold it out of the way. It is not necessary to disconnect the wires. Remove the two 10mm hex head screws located between the radio and the air vent ducts. Turn ignition on but DO NOT START vehicle. Shift into "L" low gear. Place a rag over the shifter panel to avoid scratching, and with both hands pull the radio together with the climate control straight out and set on the rag. STEP #4 Locate where the right side of the console joins to the dashboard. Place InDash bottom edge over and parallel to the separations. The top corner of the InDash should rest on the right side of the clip hole. Mark the holes and remove InDash. Drill three pilot holes, place InDash over the holes, and secure with the three screws provided. STEP #5 Push the radio and climate control back in place and secure with the four screws. Push the air vent molding back into position and push until snaps are in place then install molding strip between the climate control and the ashtray. INSTALLATION IS NOW COMPLETE. ENJOY YOUR NEW PANAVISE INDASH MOUNT. Final Install Picture on ES300 There may be recent updates to this Instruction Sheet, please visit our website or contact PanaVise Products, Inc. for the latest revision as well as for the most complete up-to-date PanaVise InDash Applications List: 7540 Colbert Dr., Reno, NV, Phone: 800.759.7535, 775.850.2900, Fax: 800.395.8002, www.panavise.com 2002 PanaVise Products, Inc.
Page 2 of 5 LEXUS SC430 02-10 instructions: Please note: The extra soft leather on this vehicle should be protected as much as possible as to not tear it. See other notes below.* STEP #1: Open the center console lid. Pull up on seat warmer bezel and release clips, pull out, and set aside. Lift up on shift lever cover, which includes, cup holder and ash tray. STEP #2: Apply emergency brake, turn ignition on, DO NOT START, shift gear shift lever into 1st gear. Disconnect radio door switch, ash tray switch, and light plug in center of bezel and set aside. STEP #3: With 10mm socket driver, remove the (2) bolts below the radio. STEP #4: With your hands, or hook tool. There are (6) plastics clips holding the climate control in place. *Be very careful when removing the climate control. Push the climate control from the back straight out towards you as to not tear the leather. Lift the climate control out of the way enough to get to the (2) 10mm screws above the radio. Remove these screws, and set aside. Tape Placement PLEASE NOTE: As an added precaution PanaVise has added a piece of tape in the InDash Kit to provide additional protection for the leather surface. Place the tape between the 3 holes and the angle with some tape over the edges. STEP #5: Place the shop towel on the console area and lift out radio, DO NOT DISCONNECT WIRING. Place the climate control partially back in place. Removal of seat heater controls STEP #6: Place the InDash by PanaVise Mount onto the right side of the dash by the radio, at a flat spot. Be sure to check the angle Screw in the (3) supplied screws. Lift up climate control, replace radio and (2) top radio screws. *Very Carefully, Replace the climate control by inserting it straight back in to place. Screw in the (2) screws at the bottom of the radio. STEP #7: Replace the shift lever cover and the seat warmer bezel. INSTALLATION IS NOW COMPLETE, ENJOY YOUR NEW INDASH BY PANAVISE MOUNT. (2) 10mm lower radio screws Finished Install Picture, SC430 There may be recent updates to this Instruction Sheet, please visit our website or contact PanaVise Products, Inc. for the latest revision as well as for the most complete up-to-date PanaVise InDash Applications List: 7540 Colbert Dr., Reno, NV, Phone: 800.759.7535, 775.850.2900, Fax: 800.395.8002, www.panavise.com 2002 PanaVise Products, Inc.
Page 3 of 5 Toyota Solara - Camry 2004-2008 instructions: STEP #1: Open the console cubby door and cubby door below climate control. With hook tool lift up on the back of the shifter/console bezel by the console cubby on the left side first to release (1) clip. Work you way down the left side releasing (2) more clips. With hook tool repeat on the right side back to release (1) clip. Apply emergency brake. Lift up on the bezel to release all remaining clips. Remove the shifter release cover, and push down on the release, then move the shifter into (2nd). Lift up on the console bezel to remove over the emergency brake and shifter by turning and lifting together. Set bezel aside. STEP #2: With your hands at the bottom sides of the cubby under the climate control, pull to release (2) clips, then (2) clips at the top of the cubby right under climate control. Lift the top out towards you and tilt it towards you to remove. Set cubby off to the left side of console. With 10mm driver remove the (2) gold bolts below the climate control that hold the radio bracket on.. STEP #3: (Carefully) With pry tool lift up on the front of the air vent and tri-display center bezel, slide pry tool into bezel to provide space to pull on bezel with hands an hook tool. It is advised to have (2) persons to do this as there are (8) total clips that need to be removed. The bezel will come straight out towards you. There are (3) clips at the front of the bezel by windshield, (3) clips below the air vents, and (2) clips on the sides by the display. It can be difficult to remove this bezel. A hook tool can be inserted into the sides of the bezel by the display (there is a small notch) to assist. Pull to release a couple of clips first, then move hook tool to the lower right then left of air vents to release (2) clips. Lift off the bezel and set up out of the way. Remove the (2) 100mm gold bolts exposed when bezel was removed. STEP #4: Lift out on the radio and climate control assembly releasing (4) clips. Set the assembly onto a shop towel on the console. Place the InDash by PanaVise at the lower right side of radio cavity by the clip slot. The back of the InDash by PanaVise Mount will line up with the edge of the dash. Install the (3) supplied screws into the mount. Hook tool into bezel Bottom bolts location Hook tool in notch Top bolts location STEP #5: Replace radio and climate control unit, and all other components in reverse order. Note: When replacing the console bezel you may need to shift into (N) to get it back in place. INSTALLATION IS NOW COMPLETE, ENJOY YOUR NEW INDASH BY PANAVISE MOUNT Final Install Picture on Solara Mount installed showing location
LEXUS ES350 2007-11 Instructions: I-75136-200 Page 4 of 5 STEP #1: Open cup holder door. With your hands, lift up on the back of the shifter bezel to release (2) clips. Continue lifting up on the bezel to release (4) more clips by the shifter. NOTE: Be careful when completing the following step as to not damage the bezel above the ashtray. Move the bezel slightly left and right while lifting up on the bezel by the ashtray to release (5) plastic clips. Lift out the bezel and disconnect the power plug. Set bezel aside. STEP #2: With the hook tool and your hands pull out the triangle shaped covers to the right and left of the console. On the left side there are (3) clips and it pulls out to the side. On the right side there are (4) clips and it is removed by pulling out from the bottom back to release (2) clips, then pulling back towards you to release the (2) final clips located along side of the glove box door. STEP #3: Remove the center air vent assembly by carefully inserting the hook tool into the lower right or left corner of the air vent pulling to just release (1) clip on each side. Then insert hook tool into the upper section and pull to completely release the air vents and disconnect the security light plug. Set air vents aside. STEP #4: With 10mm socket driver remove (2) bolts to the sides of the air vent cavity, and then (2) more located down behind where the triangle covers were removed. With emergency brake on, Safely shift the shifter to D. This can be done by removing the small cover by the shifter and pushing down on the brake pedal and button at the same time. Place the towel onto the console. With your hands lift out and up on the display / climate control/ cassette assembly, and set it onto the console. STEP #5: Locate (1 of 2) flat spots on the right side of the dash cavity that the mount fits on. (1) by the TEMP button, and the other by the Map button. See pictures. Place InDash by PanaVise on the spot. Carefully drill (3) 3/32" holes in the side of the dash. This will allow the screws to be installed easily. Install the mount with the (3) screws supplied. Console cover removal Shifter release cover removal Center Air vent removal Left triangle cover removal STEP #6: Replace the display assembly, bolts, covers, and air vents in reverse order. INSTALLATION IS NOW COMPLETE, ENJOY YOUR NEW INDASH BY PANAVISE MOUNT. Right triangle cover removal Upper Mounting Location Lower Mounting Location Display assembly
Page 5 of 5 MOUNTING LOCATION: Upper right side of radio cavity-es300 Right sideof radio cavity-sc430&es350 Right side of climate control-solara TOOLS REQUIRED: Hook tool / Pry tool/dash Tool 10mm driver/ Phillips screwdriver 3/32 drill bit and drill Masking Protective Tape/ Shop towel PARTS INCLUDED: (1) S7-1570 Mount (3) 1" needle point screws [3E] (1) 1"x2.060" Protective Tape LEXUS LS460/600 2007-2009 Instructions: NOTE: Before removing this radio control the MFG mentions to disconnect the battery terminal to disable the restraint systems. Please follow their directions STEP#1: Begin by removing the console left side panel. With a plastic dash tool, as there are (9) clips total. Repeat the same on the right side. STEP #2: Remove the shift lever knob by unscrewing it counterclockwise. STEP#3: Remove the small strip bezel behind the shifter/console bezel and at the front of the console box by releasing (4) plastic clips with the Hook/Dash Tool STEP #4: Place protective tape at the lower edge of the tray assembly. Shift the shift lever into N (neutral). Remove the (2) Phillips screws on the left side of the bezel by the shift lever. With the Hook/Dash tool release the (6) clips that hold the shifter/console bezel in place. Lift off the shifter panel and set to the side. STEP #5: Place protective tape at the lower edge of the radio control unit. Pull to detach (2) clips, set off to the side. STEP #6: Locate the (2) 10mm bolts to the left and right of the radio controls. Remove these and set aside. Pull out the radio receiver releasing (4) clips that are behind the receiver. Set the radio aside. STEP #7: To remove the display assembly and bracket, Remove the (2) 8 mm bolts below the display assembly. Pull out the display and bracket assembly that includes the air vents releasing (6) clips. Set aside. STEP #8: Place InDash by PanaVise Mount to the right side of the display. Install the (3) supplied screws. STEP #9: Replace the components in reverse order. CELL PHONE & MEDIA MOUNT INSTALLATION INSTRUCTIONS PART#: 75136-200 MFG: LEXUS / TOYOTA MODELS & YEARS: This Page: LS460/600 07-09 LEXUS - ES300 90-2001(Pg.1) SC430 02-09 (See pg.2) ES350 07-11 (See pg. 4) TOYOTA-Solara-Camry 04-07 (pg.3) (Excludes 2004 Camry Sedan) * * ADVISEMENT * * Read instructions completely prior to starting installation. All InDash Mounts are designed so that after installation, phone is facing normal driver position for left-hand drive vehicles. This mount is not designed to be used in foreign countries with right-hand drive vehicles. Use extreme care when working around the plastic components on the dash. Excess force, can cause breakage of the plastic components. InDash Installed Showing Location