Four-Post Lift Family High-capacity open- and closed-front alignment lifts WIDEST RUNWAYS! AND VALIDATED
Four-Post Lifts Available in long or short, open or closed configurations. Louvered Ramps NEW Extra-Wide Runways 26" Accommodate vehicles up to 92" wide Prevent wheel spin More effective than diamond tread or abrasive strips STANDARD Flush Slipplates Wheelbases up to 158" Tethered pins secure plates on basic models High-Capacity Two Swing Air Jacks Two Movable Work Steps Other Lift 18,000 Pounds! Lifts 18,000 lbs. (8164 kg) Best in class! Raise vehicles off runways 9,000-lb. capacity 12 secure positions Lightweight design
NEW OPTIONAL Open-Front Workspace Available % % Easy access to adjustment points and jacks Available on long- and standard-length runway racks Louvered Locks 16 lock heights ensure runways are level Long-life galvanized cables Control Unit Model L451T-IS shown with optional AlignLights system Easy-to-use console Powerful 3-hp motor STANDARD Integrated Air Line Kit STANDARD Pins and Pulleys Umbilical Covering % % Convenient power for air tools at front and rear Large-diameter iron pulleys with teflon bearings ensure long-life Chrome-plated pins Strong and flexible Protects air and hydraulic lines from damage
PowerSlide edition saves time and hassle! PowerSlide Locking System PowerSlide Slipplates Secure slipplates with a single button. The technician no longer has to struggle to remove and replace slipplate pins for every alignment. PowerSlide Control Push-button locks or unlocks the slipplates and turnplates. PATENTED PowerSlide Turnplates Save time by eliminating struggle with turnplate pins. Minimize trips around the car Yesterday's Technology Only 3 Trips! 1 2 3 1 Mount targets 2 Make adjustments 3 Remove targets 4 Jack vehicle and compensate sensors 5 Lower leveling legs (if equipped) 6 Remove slipplate and turnplate pins 7 Replace slipplate and turnplate pins 8 Raise leveling legs (if equipped) 8 Trips 8 7 6 5 4 3 2 1 Models L451T-PS, L454T-PS
FIA/Inflation Station edition maximizes productivity! PATENTED Fully Integrated Alignment with Inflation Station and PowerSlide FIA console Controls PowerSlide and Inflation Station features. Automatic locking Turnplates and slipplates lock and unlock at the right time. Locks automatically during lift descent. Model L451T-IS shown FIA allows WinAlign aligners to control lift features for ultimate productivity.* Integrated inflation reels Automatically fills or bleeds each tire. Record tire pressure Printouts record starting and final pressure. Models L451T-IS, L454T-IS * Alignment console sold separately.
STANDARD Swing Air Jacks Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations. 9,000 lbs. (4,082 kg) capacity Combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles 133-84-1 9,000-lb. Capacity Swing Air Jack OPTIONAL AlignLights system Hunter s AlignLights lighting system provides an efficient light source underneath the vehicle. Powered by the main lift power source and requires no additional or exposed electrical cords. Automatically turns off when the lift is lowered to the floor and turns on when the lift is raised. AlignLights is an ALI listed accessory. 20-2993-1 AlignLights system for four-post lifts PATENTED Turnplates All L451T and L454T models will ship with the most appropriate turnplates. When making a substitution, any of the following turnplates may be used. 20-2076-1 PowerSlide turnplates with automatic bridges Two stainless steel turnplates for camera-sensor systems. 20-2075-1 PowerSlide turnplates without automatic bridges Two stainless steel turnplates for conventional-sensor systems. 20-2532-1 Stainless steel turnplate kit Two stainless steel Delrin-ball turnplates and bolt-on guide strips. 20-2533-1 Low-friction stainless steel turnplate kit Two stainless steel Torlon ball turnplates and bolt-on guide strips. Integrated bridge lowers and raises as plates are locked, making rolling compensation a snap. Air-operated control system ties directly into PowerSlide lifts (20-2076-1 shown). 20-2531-1 Powder-coated turnplate kit Two powder-coated, Delrin-ball turnplates and bolt-on guide strips.
Standard-length lifts L451T-IS L454T-IS L451T-PS L454T-PS L451JT L454JT Open-front accessibility % % % Fully Integrated Alignment % % Inflation Station % % PowerSlide slipplates & turnplates % % % % Stainless steel turnplates % % Two 9,000-lb. Swing Air Jacks % % % % % % Specifications Max. vehicle weight 18,000 lbs. (8164 kg) Max. wheelbase General service 193 in. (4902 mm) Two-wheel alignment* 177 in. (4496 mm) Four-wheel alignment 158 in. (4013 mm) Min. four-wheel alignment 88 in. (2235 mm) Max. lifting height 75 in. (1905 mm) Alignment height Any of 16 lock positions Minimum height 8.75 in. (222 mm) Overall height 98 in. (2489 mm) Tread width Min. inside 40 in. (1016 mm) Max. outside 92 in. (2337 mm) Motor 3 hp, 208-230 VAC, 60 Hz, 1 ph Air 90-150 psi (6.2-10.3 bar)** * Long wheelbase vehicles may require jacking compensation ** 125 psi required for full jack capacity Standard equipment Stainless steel turnplates (PowerSlide turnplates on PS and IS models) Flush-mounted, full-floating slipplates (PowerSlide slipplates on PS and IS models) Louvered ramps with builtin wheel stops Built-in, full-length jack rails Two movable work steps Front wheel stops Built-in air line kit Two wheel chocks Optional equipment 20-3145-1 17.5" Ramp Extension Kit (for lowclearance vehicles) 20-3146-1 40" Ramp Extension Kit (for extremely low-clearance vehicles or high-floor-slopes) Because of continuing technological advances, specifications, models and options are subject to change without notice. 31 in. x 31 in. (787 mm x 787 mm) OF JOINTS IN CONCRETE (located under both front post baseplates) 18 ft.- 10 1/4 in. (5747 mm) 16 in. (406 mm) 28 5/8 in. (727 mm) 20 1/2 in. x 20 1/2 in. (521 mm BY 521 mm) OF JOINTS IN CONCRETE (located under both rear post baseplates) AND VALIDATED 31 1/2 in. (768 mm) 6 ft. 3 in. (1905 mm) MAXIMUM HEIGHT 15 ft.- 3 3/8 in. (4658 mm) RECOMMENDED BAY WIDTH 12 ft.- 3/8 in. (3667 mm) ROOM FOR ALIGNMENT CONSOLE HAWKEYE AND PRONTO SYSTEMS HAVE SPACE REQUIREMENTS IN FRONT OF THE LIFT THAT MUST BE MET, REFER TO APPROPRIATE SENSOR SITE REQUIREMENTS. 26 in. (660 mm) L451 plan view 28 in. (711 mm) 9 ft.- 9 3/8 in. (2981 mm) 40 in. (1016 mm) 11 ft. - 7 3/16 in. (3535 mm) 9 ft. -10 11/16 in. (3015 mm) RUNWAY LENGTH: 18 ft. - 3 in. (5563 mm) (not shown) L451 and L454 elevation view 4 in. (102 mm) MAXIMUM FLOOR ELEVATION CHANGE OF 3 in. (76 mm) BETWEEN POSTS (baseplate outer edges) FOR SHORT RUNWAYS, 18 ft. 7 1/2 in. (5677 mm) FOR LONG RUNWAYS, 21 ft. 4 in. (6502 mm) FOR ALL OPEN-FRONT LIFTS, ADD 2 3/4 in. (70 mm) (for larger front baseplates) JOINT For Lift with HE421 Floor-Mounted Sensors: FM, ML, LC or FM Typ. 27 ft. - 8 1/4 in. (8439 mm) Specified Range 28 ft. - 4 1/2 in. to 24 ft. -11 1/4 in. (8649 mm to 7601 mm) OVERALL LENGTH: 21 ft.- 9 3/4 in. (6648 mm) RECOMMENDED BAY LENGTH (Refer to 6292-T, Floor-Mounted Sensor site. ) For HE421CM: add 5 in. (127 mm) ( Refer to 6291-T.) For HE421WM: Spec Range is expanded. ( Refer to 6290-T) JOINT 8 ft. 2 in. (2489 mm) 8 1/4 in. (210 mm) MINIMUM HEIGHT 13 ft. (3962 mm) MINIMUM CEILING HEIGHT The Hunter L451 and L454 Lifts have been certified under the program conducted by Automotive Lift Institute (ALI) to comply with Safety Standard ANSI/ALI ALCTV-2011 and Electrical Standard UL 201.
Extended-length lifts L451LT-IS L454LT-IS L451LT-PS L454LT-PS L451LJT L454LJT Open-front accessibility % % % Fully Integrated Alignment % % Inflation Station % % PowerSlide slipplates & turnplates % % % % Stainless steel turnplates % % Two 9,000-lb. Swing Air Jacks % % % % % % Specifications L451L plan view*** Max. vehicle weight Max. wheelbase General service Two-wheel alignment* Four-wheel alignment Min. four-wheel alignment Max. lifting height Alignment height Minimum height Overall height Tread width Min. inside Max. outside Motor Air * Long wheelbase vehicles may require jacking compensation ** 125 psi required for full jack capacity 18,000 lbs. (8164 kg) 227 in. (5766 mm) 211 in. (5360 mm) 158 in. (4013 mm) 88 in. (2235 mm) 75 in. (1905 mm) Any of 16 lock positions 8.75 in. (222 mm) 98 in. (2489 mm) 40 in. (1016 mm) 92 in. (2337 mm) 3 hp, 208-230 VAC, 60 Hz, 1 ph 90-150 psi (6.2-10.3 bar)** 31 in. x 31 in. (787 mm x 787 mm) OF JOINTS IN CONCRETE (located under both front post baseplates) 21 ft,- 6 3/4 in. (6572 mm) 28 5/8 in. (727 mm) 20 1/2 in. x 20 1/2 in. (521 mm BY 521 mm) OF JOINTS IN CONCRETE (located under both rear post baseplates) 15 ft.- 3 3/8 in. (4658 mm) RECOMMENDED BAY WIDTH 12 ft.- 3/8 in. (3667 mm) ROOM FOR ALIGNMENT CONSOLE HAWKEYE AND PRONTO SYSTEMS HAVE SPACE REQUIREMENTS IN FRONT OF THE LIFT THAT MUST BE MET, REFER TO APPROPRIATE SENSOR SITE REQUIREMENTS. 26 in. (660 mm) 28 in. (711 mm) 9 ft.- 9 3/8 in. (2981 mm) 40 in. (1016 mm) 11 ft. - 7 3/16 in. (3535 mm) 9 ft. -10 11/16 in. (3015 mm) RUNWAY LENGTH: 20 ft.-5 1/2 in. (6236 mm) JOINT For Lift with HE421 Floor-Mounted Sensors: FM, ML, LC or FM Typ. 30 ft. - 4 3/4 in. (9265 mm) Specified Range 31 ft. - 3/4 in. to 27 ft. - 7 3/4 in. (9468 mm to 8426 mm) OVERALL LENGTH: 24 ft.- 6 1/4 in. (7474 mm) RECOMMENDED BAY LENGTH (Refer to 6292-T, Floor-Mounted Sensor site. ) For HE421CM: add 5 in. (127 mm) ( Refer to 6291-T.) For HE421WM: Spec Range is expanded. ( Refer to 6290-T) Standard and optional equipment Identical to L451 and L454 Lift Racks. 31 1/2 in. (768 mm) 4 in. (102 mm) JOINT Be sure to check out other Hunter literature for more quality products from Hunter Engineering. Because of continuing technological advances, specifications, models and options are subject to change without notice. AND VALIDATED *** See previous page for elevation view The Hunter L451L and L454L Lifts have been certified under the program conducted by Automotive Lift Institute (ALI) to comply with Safety Standard ANSI/ALI ALCTV-2011 and Electrical Standard UL 201. PowerSlide and WinAlign are registered trademarks of Hunter Engineering Company. The PowerSlide logo is a trademark of Hunter Engineering Company. 0317RH Copyright 2017, Hunter Engineering Company Form 6020-T, 03/17 Supersedes form 6020-T, 11/15