ILTERS HYDRAULIC DIVISIO TAK CARE - Return filters RC TECHICAL DATA ORDERIG AD OPTIOS CHART CLOGGIG IDICATORS PRESSURE DROP ( p) CURVES CROSS UCTIOAL VIEW SPARE PARTS ORDERIG IORMATIO DIMESIOS O THE ILTER ELEMET
ILTERS HYDRAULIC DIVISIO RC TAK CARE RETUR ILTERS MATERIALS Head Spin-on cartridge ypass valve Seals Indicator housing COMPATIILITY Aluminium alloy Steel Polyammide itrile R (KM - on request fluoroelastomer) rass ull with fluids: HH-HL-HM-HR-HV-HG (according to ISO 6743/4). or fluids different than the above mentioned, please contact our Sales Department. PRESSURE Max working psi (7 bar) Test 45 psi ( bar) ursting 3 psi (2 bar) Collapse, differential for the filter element 45 psi (3 bar) YPASS VALVE Setting WORKIG TEMPERATURE rom -5 to + 23 25 psi (.7 bar) +/-% H D2 E E2 D D3 E3 H2 Indicator port E6 H3 D E4 E5 Tank cut out: ø2.48 for RC+, ø3.7 for RC2+. Indicator port D D2 D3 H H2 H3 E E2 E3 E4 E5 E6 R* Weight lbs RC RC2 3/4 3.74.28 7.72 9.49.98.7 2.76 2.76.97.5.5 3.54 8.3.8.7+2..7+2.8 RC2 RC22 /2 5.2.35 9.92.69.42.7 3.94 3.94 2.83 2.2 2.2 4.88. 2.87.7+2.8.7+3.
TAK CARE RETUR ILTERS ORDERIG AD OPTIOS CHART R C ILTER COMPLETE ELEMET AMILY AMILY SIZE & LEGTH 2 2 22 SIZE & LEGTH PORT TYPE PT thread PORT SIZE 6 3/4" 6 6 2 "/2 2 2 YPASS VALVE 25 psi (.7 bar) SEALS SEALS nitrile R R KM luoroelastomer KM ILTER MEDIA ILTER MEDIA fiber 6 >2 fiber 6 fiber 2 >2 fiber 2 fiber 25 >2 fiber 25 cellulose >2 cellulose cellulose 25 >2 cellulose 25 CLOGGIG IDICATOR 5 nr. 2 x /8"ports, plugged 3 pressure gauge, rear connection 8 pressure switch,.o. contacts pressure switch,.c. contacts P SPDT, pressure switch P P P P AESSORIES no accessory available 5 3 8 5 3 8 5 3 8 5 3 8 E R C CLOGGIG IDICATORS A/ 2 mm /8 SP ø.57 Series 3 (rear connection) : pressure gauge, scale - 6 psi ( - 6 bar) 3.5 PG9 A/ 27 mm.22.39 /8 2.2 /8 Ø.87 A/ 24 mm.2 Series 8 (.O. contacts) & series (.C. contacts): pressure switch, max voltage 22 V AC 5-6 Hz, max current.5a resistive,.25a inductive - switching power VA, setting 22 psi (.5 bar), protection IP65 Series P: SPDT, pressure switch max voltage 25V - 5Hz max current 6A resistive,a inductive protection IP65 setting 22 psi (.5 bar) 4 2
TAK CARE RETUR ILTERS PRESSURE DROP ( p) CURVES The Assembly Pressure Drop ( p) is obtained by adding the pressure drop values of the ilter Housing and of the Clean ilter Element corresponding to the considered low Rate and it must be lower than 7 psi (.5 bar). ILTER HOUSIG PRESSURE DROP (mainly depending on the port size).4 6. RC.3.2 4.5 3. 3/4" /2"..5 3 26 4 53 66 79 92 5 CLEA ILTER ELEMET PRESSURE DROP (depending both on the internal diameter of the element and on the filter media) ERC ERC 2.75.8.5 7.2.25 3.6 6.5 3 2 26 33 4 ERC 2.75.8.5 7.2.25 3.6 6.5 3 2 26 33 4 ERC 22.75.8.75.8.5.25 7.2 3.6 3 26 4 53 66 79.5.25 7.2 3.6 3 26 4 53 66 79.. All the curves have been obtained with mineral oil having a kinematic viscosity 3 cst and specific gravity,9 ; for fluids with different features, please consider the factors described in the first part of this catalogue. When selecting the filter size, these curves must be taken into account if it is foreseen that any flow peak is to be absorbed by the bypass valve, it also must YPASS VALVE PRESSURE DROP be of proper configuration to avoid pressure peaks. The valve pressure drop is directly proportional to fluid specific gravity. 4 58. RC -2 4 58. RC 2-22 3 43.5 3 43.5 2 29. 2 29. 4.5 4.5 6.5 3 2 26 33 4 26 53 79 5 32 59.. All the curves are obtained from test done at the UI HYDRAULIC DIVISIO Laboratory, according to the specification ISO 3968. In case of discrepancy, please check the contamination level, viscosity and features of the fluid in use.
TAK CARE RETUR ILTERS CROSS UCTIOAL VIEW QUICK MAITEACE The spin-on type filter element ensures a quick and easy replacement. EASY REPLACEMET A anti-drain membrane keeps the oil inside the cartridge and avoid oil losses during the replacement. CLOGGIG IDICATOR A visual or electrical indicator is available as an option and allows monitoring of the element condition. The seat for the indicator is a standard feature. SPARE PARTS ORDERIG IORMATIO (from the code of the complete filter, fill the digits corresponding to the boxes) C Head R C Seal kit S R C DIMESIOS O THE ILTER ELEMETS Type E RC E RC2 E RC2 E RC22 A C 3.8 3.8 5.8 5.8 3/4 SP 3/4 SP /4 SP /4 SP 5.75 7.52 7.3 8.9 Area (in 2 ) Media + Media C+ 33.7 562.7 689.8 93. 52.3 735.5 86.8 4.8 Technical data subject to variations without prior notice. RC - USA - 7/25 UI Universal ilter International - Hydraulic Division: 9337 Ravenna Road, Unit G - Twinsburg, OH 4487 Phone (33) 458 - ax (33) 45 - E-mail: ufifilters@uhiltd.com UI HYDRAULIC DIVISIO - PLAET ILTERS S.p.A. via S.Chierico, 24-246 olgare G - Tel. 35 449383 - ax 35 843743 e-mail: info@ufifilter.it - http://www.ufifilter.com