Audiovox Electronics Corp. NSTALL GUDE FLC-AL(RS)-CH-EN Available for : FLCAN Rev. Date: February, 0 Doc. No.: ##086## CH please visit www.flash-it.com for complete product details The brand names and logos found in this guide are property of their respective owners. Audiovox Electronics Corp. 0 NOTCE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the nstallation Guide carefully before beginning any work.
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 install type SeLeCtiOn FEATURES MAKE MODEL nstall type requires a T-Harness to complete the installation. T-Harness sold separately. YEAR NSTALL TYPE DATA MMOBLZER BYPASS DOWNLOADABLE SOFTWARE RS COMMUNCATON -WAY COMPATBLTY PRORTY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DSARM OEM ALARM TRUNK/HATCH RELEASE POWER LFTGATE POWER SLDNG DOOR (L) POWER SLDNG DOOR (R) DATA/MUX GNTON CTRL SECURE TAKEOVER PARKNG LGHT CTRL VOLKSWAGEN RAM JEEP DODGE CHRYSLER 00 08-0 00 Limited 08-0 00c 08-0 00c SRT8 08-0 Town & Country 08- Caravan 08-0 Challenger SXT 08- Challenger R/T 08- Challenger SRT8 08- Charger SE 08-0 Charger R/T 08-0 Charger SRT8 08-0 Durango - Grand Caravan 08- Journey 09-0 Magnum 08 RAM 500 09- RAM 500 0- RAM 500 0- Commander 08-0 Grand Cherokee 08- C/V 0-500 0-500 0-500 0- Routan 09-
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 ParKing LigHt note POSTVE PARKNG LGHT (+) NEGATVE PARKNG LGHT (-) Complete the installation as shown in the wiring diagram. Complete the installation as shown in the wiring diagram. Make the following connections to control the positive parking light (+). Make the following connections to control the negative parking light (-). 0 AMPS V (+) 5 AMPS V (+) 85 87A 87 86 PARKNG LGHT (+) 85 87A 87 86 PARKNG LGHT (-) 0 0 BLUE RED (NC) GREEN DOORLOCK NVERTER DLV D/U + D/L + BLUE GREEN (NC) BLUE RED (NC) GREEN DOORLOCK NVERTER DLV D/U + D/L + BLUE GREEN (NC) WARNNG MAX 5mA PARKNG LGHT (-) OUTPUT WARNNG MAX 5mA PARKNG LGHT (-) OUTPUT Follow the module programming procedure. Follow the module programming procedure.
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 type - wire CrOSS reference CHart CONNECTOR MAKE MODEL VOLKSWAGEN RAM JEEP DODGE CHRYSLER YEAR WRE DESCRPTON NAME COLOR TYPE POSTON WRE COLOR POLARTY LOCATON COMPONENT LOCATOR 00 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ 00 Limited 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ 00C 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ 00 SRT8 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Town & Country 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Town & Country - Parking Light D Black 6 pin White/Green (MUX) Switch ~ Caravan 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Challenger R/T 08- Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Challenger SXT 08- Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Challenger SRT8 08- Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Charger SE 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Charger R/T 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Charger SRT8 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Durango - Parking Light D Black 6 pin White/Green (MUX) Switch ~ Grand Caravan 08-0 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Grand Caravan - Parking Light D Black 6 pin White/Green (MUX) Switch ~ Journey 09-0 Parking Light ~ ~ ~ ~ White/Violet (+) Driver kick panel ~ Magnum 08 Parking Light D Black 0 pin White/Brown (MUX) Switch ~ Ram 500 09- Parking Light D Black 0 pin White (MUX) Switch ~ Ram 500 0- Parking Light D Black 0 pin White (MUX) Switch ~ Ram 500 0- Parking Light D Black 0 pin White (MUX) Switch ~ Commander 08-0 Parking Light ~ ~ ~ Relay #7 (-) Power module in engine compartment ~ Grand cherokee 08- Parking Light ~ ~ ~ Relay #7 (-) Power module in engine compartment ~ C/V 0 Parking Light D Black 0 pin White/brown (MUX) Switch ~ C/V - Parking Light D Black 6 pin White/green (MUX) Switch ~ 500 0- Parking Light D Black 0 pin White (MUX) Switch ~ 500 0- Parking Light D Black 0 pin White (MUX) Switch ~ 500 0- Parking Light D Black 0 pin White (MUX) Switch ~ Routan 09- Parking Light D Black 0 pin White/brown (MUX) Switch ~
Page 5 of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 type - wiring diagram REFER TO ASSEMBLY FOR PROPER CONNECTONS AND MATCH EACH LETTER ACCORDNGLY RF KT SOLD SEPARATELY SEE DSTRBUTOR FOR AVALABLE MODELS E PARKNG LGHT CONNECTON OR F VEHCLE S EQUPPED WTH (+) OR (-) PARKNG LGHT READ: PARKNG LGHT F VEHCLE S EQUPPED WTH MUX PARKNG LGHT CONNECT TO VEHCLE HOOD SWTCH DRVER DOOR PN D HOOD SWTCH (-) NPUT - GREEN/BLACK (NC) BLUE/BLACK (NC) RED/WHTE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHTE (NC) BLACK/WHTE RAP SHUTDOWN (-) OUTPUT - GREEN (NC) PURPLE/WHTE A YELLOW/BLACK YELLOW/RED (NC) YELLOW B C G FLCHH (OLD) ASSEMBLY REQURED - SOLD SEPARATELY VEHCLE HARNESS FLCHH (NEW) ASSEMBLY REQURED - SOLD SEPARATELY VEHCLE HARNESS E D A B C G OR E D A B C G
Page 6 of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 module PrOgramming PrOCedUre Close driver door. 6 OFF Turn key to OFF position. Re-open driver door to wake up data bus. 7 Remove key. nsert key into ignition. 8 UNLOCK Press UNLOCK on the OEM remote. ON Turn key to ON position. f vehicle is not equipped with OEM remote, press module programming button. LED will turn solid RED. 9 Wait, LED will turn solid GREEN for seconds. 5 Within 5 seconds, LED will flash GREEN rapidly. 0 Module Programming Procedure completed.
Page 7 of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 module PrOgramming installation PrOCedUre mode SeLeCtiOn - PUSH to Start Press Close driver and release door. programming button to select installation mode. LED flashes (X) once = DATA Re-open MODE driver door to wake up LED flashes (X) twice = STANDARD data bus. HARDWRE MODE x DO NOT PRESS BRAKE PEDAL Push start button twice [x] to ON position. LED will turn solid RED. 5 6 7 Press DO NOT and PRESS hold BRAKE PEDAL programming button until Push LED start turns button solid once GREEN [x] to to OFF register position. selection. After registration, follow Factory Press UNLOCK Reset Procedure on the OEM to change installation mode and remote. restart this procedure. UNLOCK x Wait, LED will turn solid GREEN for seconds. Within 5 seconds, LED will flash GREEN rapidly. 8 Module Programming Procedure completed.
Page 8 of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 VaLet mode PrOgramming PrOCedUre n Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. OFF Wait, LED will turn solid RED for seconds. Turn key to OFF position. TME RESTRCTN COMNG UP nsert key into ignition. OFF TME RESTRCTN ON x5 Complete this step within 7 SECONDS. Turn key to OFF position then to ON position five times [5x] rapidly. 5 6 Remove key. To exit valet mode: repeat steps to 6. Valet Mode Programming Procedure completed.
Page 9 of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 aftermarket remote PrOgramming All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
Page 0 of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 module navigation PrOCedUre V t is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. Use the Module Navigation Chart on the next page. Module must be programmed to the vehicle. Set ignition to OFF position. To exit the Module Navigation at any time: Follow step 8. To access the MENUS: Press and hold programming button until LED turns solid GREEN. Release programming button. 6 7 n the SETTNGS: Press the programming button as many times as neccesary to access your setting. LED will flash GREEN an equal amount of times continuously. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. To save and return to the OPTONS: Press and hold programming button until LED turns solid RED. Release programming button. n the MENUS: Press the programming button as many times as the menu number indicates. LED will flash RED as many times as the current option number continuously. Configure every other setting and proceed to step 8. LED will flash GREEN an equal amount of times continuously. 8 MANDATORY: EXT MODULE NAVGATON To access the OPTONS: Press and hold programming button until LED turns solid RED. Release programming button. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. n the OPTONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. 9 Module navigation completed. Failure to exit the Module Navigation will drain vehicle battery. 5 To access the SETTNGS: Press and hold programming button until LED turns solid GREEN. Release programming button. LED will flash GREEN as many times as the current (or default) setting number, continuously.
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. module navigation CHart MENUS OPTONS SETTNGS DSARM/UNLOCK BEFORE OFF START ON OFF RELOCK AFTER START ON OFF RELOCK AFTER SHUTDOWN ON FORCE UNLOCK ALL ON FRST OFF PRESS ON ENABLE 5 TAKEOVER DSABLE* 5 SEC 90 SEC 6 SECURE TAKEOVER DELAY 0 MN 0 MN DSABLE 7 FACTORY KEYLESS N/A RS SEQUENCE LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK 0 MN 05 MN 0 MN 5 MN 8 MODULE RUN TME 5 5 MN 6 0 MN 7 5 MN 8 5 MN 0 SEC 05 SEC 08 SEC 0 SEC 9 WAT TO START DELAY 5 5 SEC 6 0 SEC 7 5 SEC 8 0 SEC 0 N/A N/A N/A N/A N/A N/A N/A N/A Technical Support Only 5 Technical Support Only 6 Technical Support Only 7 Technical Support Only *Vehicle will shudown when a door is opened. CONFGURATON
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 remote Starter error COdeS WARNNG: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. [X] NUMBER OF PARKNG LGHT REMOTE STARTER ERROR CODES FLASHES Foot brake is ON. Hood is open. 5 Engine tach signal is lost. 6 System is in Valet Mode. 7 Vehicle is moving (VSS). 8 Glow plug timeout error.
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 identify VeHiCLe year Locate the Vehicle dentification Number (VN) and identify the 0th character. A 5 Y N 5 T A L 8 D 5 R 0 X Match the VN s 0th character to its corresponding year. L > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 N > 99 V > 997 > 00 7 > 007 C > 0 P > 99 W > 998 > 00 8 > 008 D > 0 R > 99 X > 999 > 00 9 > 009 E > 0 LED STATUS Flashing RED DAGNOSTCS DURNG PROGRAMMNG DURNG REMOTE START WTH GNTON OFF Missing/wrong information from firmware or vehicle ncorrectly programmed Solid RED Waiting for more vehicle information ncorrectly programmed Flashing GREEN Additional steps required to complete programming module diagnostics Correctly programmed and operational ncorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed nvalid ground when running status from remote starter At rest and ready for a remote start sequence FaCtOry reset PrOCedUre DSCONNECT all connectors from module EXCEPT the black -PN standard or optional data connector. DSCONNECT black -PN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. PRESS AND HOLD programming button while connecting either -PN standard or optional data connector. When LED flashes red, RELEASE programming button. 7 Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGNE error message.
Page of FLC-AL(RS)-CH-EN Doc. No.: ##086## 00 All vehicle doors must be closed and locked prior to remote start sequence. take OVer PrOCedUre - to the VeHiCLe Owner Press UNLOCK on after-market remote. ON Turn key to ON position. Wait seconds for key validation. Press and release BRAKE pedal. nsert key into ignition. 5 Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. take OVer PrOCedUre - PUSH to Start - to the VeHiCLe Owner All vehicle doors must be closed and locked prior to remote start sequence. Press and release BRAKE pedal. x Press UNLOCK on after-market remote. DO NOT PRESS BRAKE PEDAL Push start button twice [x] to ON position. Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. Wait seconds for key validation.