SECTION 15440 PLUMBING FIXTURES, TRIM, AND SUPPORTS SPECIFIER: CSI MasterFormat 2004 number: 224400. PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. Division 10 - Toilet Room Accessories. 2. Division 11 - Laboratory Equipment; Food Service Equipment. 3. 15410 - Piping (Plumbing). 4. 15430 - Piping Specialties (Plumbing). 1.2 SUBMITTALS A. Submit Shop Drawings for the following: 1. Fixtures: Catalog cuts with rough-in dimensions identified as designated in fixture schedule, riser diagrams, and as specified. 2. Faucets: Catalog cuts and templates for drilled openings. 3. Fixture Trim: Catalog cuts. 4. Carriers: Catalog cuts. 1.3 QUALITY ASSURANCE A. Certification: Submit letters, signed by the installer of the product, attesting that no lead is contained in any piece of equipment or in the piping connections that could contaminate water, drinks, or food by contact. B. Comply with Florida Building Code (FBC). PART 2 PRODUCTS 2.1 MANUFACTURERS A. Fixtures: 1. American Standard. 2. Acorn Engineering. 3. Bradley. 4. Fiat. 5. Elkay. 6. Kohler. 7. Kreolab 8. Toto. 9. Zurn Project No. MASTER SPECIFICATIONS 15440-1
B. Fittings: 1. American Standard. 2. Chicago Faucets. 3. Fiat. 4. Elkay. 5. Powers Process Controls. 6. Symmons Industries. 7. Sloan. 8. T & S Brass. 9. Toto. 10. Zurn. C. Equipment: 1. Guy Gray. 2. Haws. 3. Halsey Taylor. 4. Oasis. NOTE TO SPECIFIER: Use the following, or similar, designations at fixture schedule, riser diagrams, and as necessary for the specified fixtures: WC-1 Water closet, WC-2 Water closet ADA accessible UR-1 Urinal UR-2 Urinal ADA accessible L-1 Lavatory, wall hung, ADA accessible L-2 Lavatory, counter top L-3 Lavatory L-4 Lavatory with hot water SH-1 Shower, individual, ADA accessible SH-2 Shower, group SK-1 Sink, stainless steel, single compartment SK-2 Sink, stainless steel, double compartment SSK-1 Service sink BSK-1 Bubbler Sink at Classroom Service Center MR-1 Mop receptor ARSK-1 Acid resistant sink EWC-1 Electric water cooler, EWC-2 Electric water cooler Hi-Lo ADA accessible PLSK-1 Plaster sink FD-1 Floor drain at finished areas FD-2 Floor drain at equipment rooms FD-3 Floor drain at kitchens FD-4 Floor drain at kitchen with funnel FS-1 Floor sink at kitchen Project No. MASTER SPECIFICATIONS 15440-2
2.2 FIXTURES A. Water Closets: NOTE TO SPECIFIER: Coordinate the models of the water closets specified with the height requirements found in the M-DCPS Design Guidelines and the ADAAG, giving proper consideration to both age and grade requirements based on scope of the project. Obtain the grade classification of spaces serving pre-k through 3 rd grade age groups from the M-DCPS Facilities Design and Standards before opting to use seat heights below 14 inches above the floor. Mounting heights shall be shown on the architectural toilet room elevations. 1. Wall Hung Water Closet HC Accessible (WC - ) with seat height as shown on drawings: a. White vitreous china, top spud, siphon jet flush action, 1.28 gpf, elongated bowl, with ceramic bolt caps. 1) Afwall FloWise - 2294.011EC by American Standard, or other A/E approved equivalent by Kohler, Toto or Zurn. b. Flush Valve: Sloan Royal 111-1.28 or other A/E approved equivalent by Kohler, Toto, or Zurn. c. Seat: White, elongated, open front less cover, with self-sustaining, stainless steel posts and pintles check hinges and antimicrobial agent. 1) As manufactured by Olsonite, Kohler, Toto or Zurn. 2. Wall Hung Water Closet not HC Accessible (WC - ): Same as (WC - ) above, but mount with seat height as shown on drawings. 3. Floor Mounted Water Closet HC and not HC accessible (WC - ): a. White vitreous china, top spud, siphon jet flush action, 1.28 gpf, elongated bowl, with ceramic bolt caps. 1) Madera FloWise 2259.001 (14 inches high); 2855.128 (15 inches high) or 2854.128 (16-1/2 inches high) model suited to the seat height shown on drawings, or other A/E approved equivalent by Kohler, Toto or Zurn. b. Flush Valve: Sloan Royal 111-1.28 or other A/E approved equivalent by Kohler, Toto, or Zurn. c. Seat: White, elongated, open front less cover, with self-sustaining stainless steel posts and pintles check hinges, and antimicrobial agents. 1) As manufactured by Olsonite, Kohler, Toto or Zurn. Project No. MASTER SPECIFICATIONS 15440-3
B. Urinals: 1. Urinal HC accessible (UR - ) a. Wall Hung, white vitreous china, siphon jet flush action, 3/4" top inlet spud, 0.5 gpf. Install with rim height of 17 inches above finished floor. 1) Allbrook Flowise 6550.501 by American Standard, or other A/E approved equivalent by Kohler, Toto or Zurn. b. Flush Valve: Oscillating non hold open handle. 186-05 by Sloan Royal, or other A/E approved equivalent by Sloan Kohler, Toto or Zurn. 2. Urinal (UR- ) not HC accessible same as (UR- ) above, but mounted with rim height as shown on drawings. C. Lavatories: 1. HC and not HC accessible (L-, L- ): a. Wall Hung enameled cast iron, 20 inches x 18 inches, with lug holes for concealed carrier arms. 1) Hudson K-2812 for cold water or K-2867 for hot and cold water. By Kohler or b. Cold Water Fitting: Accessible, single lavatory fitting, self-closing metering, adjustable time cycle, push handle, vandal resistant aerator 0.5 gpm maximum flow. 1) Chicago Faucets 333-E2805 or other A/E approved equivalent by Kohler, Moen or Symmons. c. Hot and Cold water Fitting: Accessible, 4 inch centers, 5 inch spout, lever handle, vandal resistant aerator 0.5 gpm maximum flow, with temperature and pressure compensation, ASSE 1070 compliant. 1) Powers TempTAP, Series 105/115, or other A/E approved equivalent by Kohler, Moen or Symmons. d. Supply Pipes: 3/8 chrome plated flexible, with loose key control, by McGuire or e. P Trap: Adjustable with offset at HC accessible lavatories, and tubing drain to wall, cleanout plug and wall escutcheon, by McGuire or other A/E approved equivalent. f. Grid Strainer: Perforated, chrome plated, 1-1/4" diameter offset tailpiece, swivel joint, HC compliant at accessible lavatories. By McGuire or other A/E approved equivalent. Project No. MASTER SPECIFICATIONS 15440-4
g. Under sink Safety Covers: Shall conform to ADAAG. 1) Handi Lav-Guard Insulation Kit 101/106 as required, white, by Truebro or 2) Use manufacturer fastening system. 2. Countertop Mounted Lav (L- ): a. White enameled cast iron, 19 inches x 16 inches, self-rimming centers. 1) Farmington K-2905-1 or -4 by Kohler, or A/E approved equivalent by American Standard or others. b. Cold Water Fitting: Accessible, single lavatory fitting, self-closing metering, adjustable time cycle, push handle, vandal resistant aerator 0.5 gpm maximum flow. 1) Chicago Faucets 333-E2805 or other A/E approved equivalent by Kohler, Moen or Symmons. c. Hot and Cold Water Fitting: Accessible, 4 inch centers, 5 inch spout, lever handle, vandal resistant aerator 0.5 gpm maximum flow, with temperature and pressure compensation, ASSE 1070 compliant. 1) Powers TempTAP, Series 105/115, or other A/E approved equivalent by Kohler, Moen or Symmons. d. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or e. "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or f. Grid Strainer: Perforated, chrome plated, 1-1/4 diameter offset tailpiece, swivel joint. By McGuire or g. Under sink Safety Covers: Shall conform to ADAAG. 1) Handi Lav-Guard Insulation Kit 101/106 as required, white, by Truebro, or 2) Use manufacturer's fastening system. NOTE TO SPECIFIER: The use of multi-station wash fountains are not acceptable unless required by the Educational Specifications or approved on a per condition basis by M-DCPS Office of Facilities Design and Standards. Such units, when approved, shall be ADAAG compliant. Edit the following item as needed. 3. Wash Fountain (WSHF - ): a. Resin and filler composition, 3 station unit with air valve, hand control, cold water only, and soap dispenser. 1) Terreon Wall-Hung Tri-Fount by Bradley or other A/E approved equivalent by Acorn. Project No. MASTER SPECIFICATIONS 15440-5
D. Shower (SH- ): 1. Individual Showers: a. Thermostatic mixing valve with integral service stops and hand held showerhead, 48 inch minimum wall bar, 5 foot long chrome plated hose. 1) Series 450-e700 with temperature and pressure compensation, ASSE 1016 compliant, by Powers Process Controls or other A/E approved equivalent by Symmons. 2. Group Showers. a. Shower Ware, 16 Gauge, Type 304 stainless steel, stain finish shower module complete with shower heads, recessed soap dishes, and control valves at each station. Stations to be at 36 on-centers, with length of module and number of stations as indicated on drawings. Shower heads shall be at 6 feet above finished floor. Module to be factory pre-piped and pressure tested. Heads shall be restricted to 1.5 gpm flow. 1) Shower Ware 115-W-F-G-RD by Acorn or b. Showerhead: Vandal resistant with concealed mounting screws, adjustable spray pattern by user, 15-degree spray angle, brass construction, flow not to exceed 1.5 gpm. 1) 295 Fre-Flo institutional head by Symmons or other A/E approved accepted equivalent. 3. Locker Room Showers Central Control: Thermostatic type mixing valve to blend hot and cold water to desired temperature and compensate for both temperature and pressure changes in supply lines, ASSE 1017 compliant, bronze body with noncorrosive parts, integral check stops, tamperproof temperature control, polished chrome, 85 degrees F. to 115 degrees F. minimum range. E. Sinks: a. Valve shall be enclosed in stainless steel cabinet with all piping finished in polished chrome. b. Provide outlet dial thermometer and control valve. Cabinet shall have top outlet and inlets. c. Series LFSH 1432 valve by Powers Process Controls or other A/E approved equivalent. NOTE TO SPECIFIER: Change or add sinks of the sizes, configuration and trim as required by the Educational Specifications for the project. Sink construction shall be as specified below unless otherwise required. Single compartment sinks shall be fitted with fixed goosenecks unless noted; multiple compartment sinks shall have goosenecks with adjustable swing. 1. Single Compartment Stainless Steel Sink with Bubbler (Classroom Service Center):(BSK- ) Project No. MASTER SPECIFICATIONS 15440-6
******************************************************************************************************** NOTE TO SPECIFIER: Use the following sink for a forward accessibility approach. Coordinate counter heights with sink depths of 5 to 6.0 inches. ******************************************************************************************************** a. (BSK - ) 25 inches x 17 inches, (5.0) inches deep, 18 gage, Type 304 stainless steel, self-rimming, double ledge. NOTE TO SPECIFIER: Use the following sink for FBC parallel accessibility approach and other program required locations. b. (BSK - ) 25 inches x 17 inches, ( ) inches deep, 18 gage, Type 304 stainless steel, self-rimming, double ledge. 1) DRKAD-2517 by Elkay, or c. Bubbler: With flexible guard and HC accessible push button valve. 1) LK-1141A by Elkay or d. Fitting: Accessible gooseneck fixed faucet, single hole inlet, 5-1/4 inch spout, lever handle, vandal resistant aerator. 1) Chicago Faucets 350-E35VPABCP or other A/E approved equivalent by Elkay, or American Standards. e. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or f. "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or g. Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or 2. Countertop (SK- ): a. Single compartment, type 304 stainless steel, 18 gage, self-rimming. 25 inches x 22 inches x ( ) inches deep. One or three holes, to suit faucet. 1) LRAD 2522 by Elkay or b. Cold Water Fitting: Accessible gooseneck fixed faucet, single-hole inlet, 5-1/4 inch spout, lever handle, and vandal-resistant aerator. 1) Chicago Faucets 350-E35VDABCP, or other A/E approved equivalent by Elkay or American Standard. c. Hot and Cold Water Fitting: Accessible, 8 inch centers, 6 inch spout, lever handle, 0.5 gpm maximum flow, vandal resistant aerator, with temperature and pressure compensation, ASSE 1070 compliant. 1) Powers TempTAP, Series 205/215 or other A/E approved equivalent by Kohler, Moen or Symmons. Project No. MASTER SPECIFICATIONS 15440-7
d. Hot and Cold Water Fitting at Clinic: Accessible gooseneck faucet with restricted swing, 5-3/8 inch spout, lever handle, vandal resistant aerator. 1) Chicago Faucets 786-GR or other A/E approved equivalent by American Standard, or Kohler. e. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or f. "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or g. Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or 3. Countertop (SK- ): a. Double compartment Type 304 stainless steel, 18 gage, self-rimming. (33 inches X 22 inches X ( ) inches deep), One or three holes to suit Faucet. 1) LRAD 3322A by Elkay, or b. Cold Water Fitting: Accessible gooseneck faucet with restricted swing, single hole inlet, 5-3/8 spout, lever handle, and vandal-resistant aerator. 1) Chicago Faucets 786-GR or other A/E approved equivalent by American Standard or Kohler. 2) Connect cold water service to both faucet inlets. c. Hot and Cold Water Fitting: Same as specified for Cold Water above. Provide complete with lavatory tempering valve, Powers LFe480, ASSE 1070 compliant, 0.5 gpm maximum flow. d. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or e. "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or f. Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or 4. Wash Sink (WS - ): a. Enameled cast iron, 72 inches x 18 inches x 7 inch (water depth), drilled back. 1) Brockway K-3204 by Kohler, or b. Fitting: Three exposed yoke faucets, wall mounted, vacuum breaker, stops in shanks. 1) Cannock K-8892-RP by Kohler, or c. Solids Interceptor: Gasketed cover, stainless steel screens 1) Josam 61030 or Project No. MASTER SPECIFICATIONS 15440-8
d. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or e. "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or f. Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or 5. Service Sink (SSK - ): a. Enameled cast iron, 22 inches x 18 inches, plain back, stainless steel rim guard. 1) Kohler 6718 or other A/E approved equivalent by American Standard or Zurn. b. Fitting: Accessible exposed yoke faucet, wall mounted, vacuum breaker, top brace, pail hook, stops in shanks and 3/4" hose threaded spout, rough plated. 1) Heritage 8354.112 by American Standard or other A/E approved equivalent by Chicago faucet, Fiat, Kohler or T & S Brass. c. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or d. 3-inch "P" Trap: Standard and Strainer, with outlet to wall, by sink manufacturer. 6. Mop Receptor (MR - ): a. Molded resin, 24 inches x 24 inches x 10 inches, rim guards, center drain. Install in room corner. b. Model MSR-2424 by Florestone or other A/E approved equivalent by Fiat. c. Fitting: Same as Service Sink (SSK). d. MR 370 5/8" diameter Hose. e. MR-372 Mop hanger with 3 clamps. f. Two MR 373 stainless steel 20 Gauge, 24" rim guards. g. Two MR-377 stainless steel splash panels. 7. Countertop Sink for 2-D Art Lab (SK- ): a. Single compartment, type 304 stainless steel, 18 gage, self-rimming. One or three holes, to suit faucet. Size to be as follows: 1) At Elementary, K-8 Centers and Middle Schools: 22 inches x 22 inches x 10-1/8 inches deep. DLR222210 by Elkay or approved equivalent. 2) At Senior High Schools: 31 inches x 22 inches x 11-5/8 inches deep. DLR312212 by Elkay or approved equivalent. b. Cold Water Fitting: Accessible gooseneck faucet with restricted swing, single hole inlet, 5-3/8 spout, lever handle, vandal resistant aerator. 1) Chicago Faucets 786-GR, or approved equivalent by American Standard or Kohler. Project No. MASTER SPECIFICATIONS 15440-9
c. Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or accepted equivalent. d. "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or accepted equivalent. e. Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or accepted equivalent. f. On floor solids interceptor, Josam 61030, as specified herein. 8. Sinks for 3-D Art Lab and Photography Lab: a. Wash Sink for 3-D Lab and Photography Lab (WS- ): 1) Type 304 stainless steel sink, 18 gauge, 72 inches long x 20 inches wide x 8 inches deep, three station, wall mounted, furnished with hangers and stainless steel brackets. a) Elkay Model EWMA-7220.or accepted Equivalent. 2) Fittings: Accessible, three, chrome plated mixing faucets, each with 6 lever handle, restricted-swing gooseneck spout, vandal resistant anti-hose aerator. a) Model LK940GN by Elkay or accepted equivalent. 3) Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or accepted equivalent. 4) Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or accepted equivalent. 5) On floor solids interceptor, Josam 61030, as specified herein. b. Countertop Sink for 3-D Art Lab (SK- ) 1) Double compartment, type 304 stainless steel, 18 gage, self-rimming. 33 inches x 22 inches x 8-1/8 inches deep. One or three holes, to suit faucet. a) LR3322 by Elkay, or approved equivalent. 2) Cold Water Fitting: Accessible gooseneck faucet with restricted swing, single hole inlet, 5-3/8 spout, lever handle, vandal resistant aerator. a) Chicago Faucets 786-GR, or approved equivalent by American Standard or Kohler. Connect cold water service to both faucet inlets. 3) Supply Pipe: 3/8" chrome plated flexible, with loose key control. By McGuire or accepted equivalent. 4) "P" Trap: Adjustable with tubing drain to wall, cleanout plug and wall escutcheon. By McGuire or accepted equivalent. 5) Grid Strainer: Perforated, chrome plated, 1-1/2 diameter offset tailpiece, swivel joint. By McGuire or accepted equivalent. 6) On floor solids interceptor, Josam 61030, as specified herein. Project No. MASTER SPECIFICATIONS 15440-10
F. Drench Hose Speakman SE-921 countertop mounted, with self-closing valve, aerated spray, 6 inch hose and flip top dust covers. G. Hose Reel (HR- ) 1. 35 feet of retractable 3/8 I.D. hose, hose bumper with hose spring and push lock hose end, for concealed installations, backflow preventer, shut-off valve, VOC concealed 2 valve fitting, loose key check valve, volume control with coupling. a. 536-537WCNF with 548 stainless steel housing and main shaft and swivel, by Chicago Faucets or NOTE TO SPECIFIER: Specify hot water faucets in compliance with ASSE 1070. Provide tempering valve when such a faucet is not commercially available. H. Undercounter Tempering Value: 1. Powers LFe480, ASSE 1070 compliant, 0.5 gpm minimum flow. I. Lab Equipment: 1. Connect sinks, fittings, gas turrets, and drain outlets associated with, but not limited to the following as specified in Division 11. a. Instructors Demo Desk. b. Student Stations. c. Rinse-Away Sinks. d. Base Wall Counters. e. Preparation Work Counters. f. Fume Hoods. g. Safety Centers. 2. Water Supplies: 3/8" chrome plated flexible, with loose key control. By McGuire or othet A/E approved equivalent. 3. Gas Supplies: 3/8" galvanized pipe, gas cock with loose key control, dirt leg and union. 4. P-traps: 1-1/2" acid resistant material same as piping used. Installation according to manufacturer s recommendations. J. Washing Machine Utility Connection Box: 1. Recessed metal box with hot and cold water hose bibbs, vacuum breakers, and 2- inch diameter drain where indicated on drawings. 2. Model WB-200 by Guy Gray with Watts Model 2T "Duo Cloz" ball type valve or other A/E approved equivalents. K. Accessible Safety Shower/Eyewash: Forward accessibility, triangular pull handle to operate shower and push (at other than Laboratory locations) flag to operate eyewash supply (at other than Laboratory locations). Project No. MASTER SPECIFICATIONS 15440-11
1. Series SE-603 by Speakman or L. Modular Shower Privacy Compartments: 1. Wall mounted 16 gage stainless steel with No. 4 satin finish. 2. Provide 1106 white vinyl shower curtain, 1104-2 chrome plated brass double hook and 1102-1 hardwood seat. 3. Furnish one compartment without seat for location by A/E of a fold down seat for handicapped use. 4. Diana Series, Model 1110 by Acorn Engineering or M. Hydrotherapy Baths:(HB- ) 1. 110-gallon mobile unit, Type 304 stainless steel satin finish walls with, 56 inches long x 24 inches wide x 25 inches deep, with whirlpool lift mechanism for 3 foot height adjustment. a. Whitehall Manufacturing Model S110M Sports Whirlpool with Hydro-lift turbine or N. Electric Water Coolers HC Accessible (EWC - ): 1. Single-Level: a. Wall Mounted, with one bottle filling station, self-closing valve with automatic stream regulator, vandal resistant polished chrome plated brass bubbler, push bars in front and both sides, for handicapped and standard use, equipped with lead reduction filter at interior locations only, satin stainless steel sides. Refer to Drawings for mounting height. 2. Bi-Level: 1) Elkay model LZS8KWSVRSK or other A/E approved equivalent by Halsey Taylor, Haws or Oasis. a. Wall Mounted, with one bottle filling station, self-closing valve with automatic stream regulator, vandal resistant polished chrome plated brass bubbler, push bars in front and both sides, for handicapped and standard use, equipped with lead reduction filter at interior locations only, satin stainless steel sides. Refer to Drawings for mounting height. 1) Elkay model LZSTL8WSVRSK or other A/E approved equivalent by Halsey Taylor, Haws or Oasis. 3. No lead shall be allowed in the manufacture of any piece of equipment within water coolers or in any piping joint or connection within the unit or pipe leading to it. O. Drinking Fountains (DF - ): 1. Wall mounted, solid one piece molded satin stainless steel construction, with selfclosing valve and automatic stream regulator, front pushbutton, vandal resistant polished chrome plated brass bubbler. See Drawings for mounting elevations. Project No. MASTER SPECIFICATIONS 15440-12
a. Halsey Taylor: Model HRFE with 45392C bubbler or other A/E approved equivalent by Elkay, Haws or Oasis. b. No lead shall be allowed in the manufacture of any piece of equipment within water coolers or in any piping joint or connection within the unit or piping leading to it. P. Interceptors: 1. Trap type, solids interceptor, bottom access, 1-1/2" slip joint, gasketed covered, removable stainless steel strainer basket, chrome plated. a. Series 61000 by Josam, or 2. On floor type, solids interceptor, top access, 2-inch threaded connections, gasketed cover, coated cast iron, galvanized steel basket with stainless steel screens. a. Series 61040 by Josam or 3. Hair/Lint interceptor, Dura-Coated cast iron hair and solids interceptor with slip joint inlet and threaded outlet, 16X16 mesh stainless steel basket removable from top, with flanged and gasketed cleanout cover with raised hex head. a. Series Series 61800 by Josam or Q. Plaster Interceptors: 1. Low Volume: Z 1180 by Zurn or 2. High Volume: Z 1181 by Zurn or R. Plumbing Fittings for Kitchen Equipment: Note to Specifier: Coordinate requirements with Food Service and Nutrition Office and Division 11. ************************************************************************************************************ 1. Cook's Table: a. Deck faucet with 6 inch swing nozzle, 8 inch centers, removable seats, chrome plated lever handles: B-1120 by T & S Brass or b. Quick opening drain with perforated grid strainer and lever handle: LK24RT by Elkay or c. Angle supplies with chrome plated flexible riser and loose key: LK-1005 by Elkay or d. Chrome plated P-Traps. e. Table furnished under Division 11. 2. Baker's Table: a. Same as for Cook's Table. 3. Vegetable/Salad Sink (2 compartment sink): Project No. MASTER SPECIFICATIONS 15440-13
a. Back splash mounting with 12-inch swing nozzle, 8 inch centers, removable seats, chrome plated lever handles: B-1128 by T & S Brass or other A/E approved equivalent. b. Two quick opening drain valves with overflow openings: LK 24RT by Elkay or c. Angle supplies with chrome plated flexible riser and loose key: LK-1005 by Elkay or d. Chrome plated P-Traps. e. Sink furnished under Division 11. 4. Pot Wash Sink (3 compartments): a. Two faucets and three quick opening valves: Same as specified for vegetable/salad sink. b. Grid strainer with tailpiece for skimmer compartment: LK-8 by Elkay or other A/E approved equivalent. c. Angle supplies with chrome plated flexible riser and loose key: LK-1005 by Elkay or d. Chrome plated P-Traps. e. Sink furnished under Division 11. 5. Kitchen Hands-Free Pedestal Base Sink: 2.3 CARRIERS a. Stainless steel construction with: 1) Hands-Free splash mounted gooseneck faucet with aerator. 2) Single toot petal mixing valve for water operation. 3) Stainless steel Basket drain, 1-1/2" tailpiece. 4) Angle supplies with chrome plated flexible riser and loose key, LK-1005 by Elkay or accepted equivalent. 5) Chrome plated P-trap. b. Advance Tabco, Model 7-PS-95 or other A/E approved equivalent by Aero Manufacturing or Eagle Group. A. All carriers shall be fully bolted to floor and installed as recommended by manufacturer. 1. Lavatory/Lavatory HC: a. Rectangular structural steel uprights with integral welded heavy steel foot, cast iron concealed arms. Model 17100 by Josam or 2. Urinal: a. Rectangular structural steel uprights with integral welded steel foot, hanger bracket and lower bearing plate. Model 17560 by Josam or other A/E approved equivalent. Project No. MASTER SPECIFICATIONS 15440-14
3. Water Closet: a. 4-inch pipe size, with pylon feet, adjustable, provided with vandal resistant trim, supply pipe support and adjustable chase extensions. Josam 12000 Series Chase-Saver II or PART 3 EXECUTION 3.1 INSPECTION A. Do not proceed with the work of this section until conditions detrimental to the proper and timely completion of the work have been corrected. 3.2 EQUIPMENT AND FIXTURE CONNECTIONS A. Provide necessary material and labor to connect fixtures and equipment having plumbing connections including fixtures and equipment specified and furnished in other sections. B. Supply Pipe Cut-off Valves: On supply pipes to each item of equipment or fixture (except faucets furnished with an integral stop) install a cutoff valve to enable isolation of the item of equipment or fixture for repair and maintenance without interfering with operation of other items of equipment or fixtures C. Anchor supply piping serving all items of equipment or fixtures to structure, to prevent pipe or fixture movement. D. Templates: Furnish templates and rough opening dimensions to fabricators of countertops and case work for location and sizes of openings for faucets and sink. END OF SECTION Project No. MASTER SPECIFICATIONS 15440-15