INFORMATION Textile shelf system
1 Transporter 20
Textile shelf system TRANSPORTER Today it s parcels, tomorrow flat screen TVs and then refrigerators. Up until now, some goods could not have been transported safely with just one load restraint system. And let s face it, some goods have to be accessible at all time. With TransSAFE and just a few hand movements you have a flexible and easy to install textile shelf system in your transporter. It s exactly where you need it at all times! Installation time and empty runs are reduced to an absolute minimum. Additionally, the shoring beams and nets are light-weight and have little to no effect on your payload. Suitable for securing: parcels of different sizes courier shipments heavy loads nearly every shape of freight 1 TransSAFE offers a textile shelf system for the securing of goods in shortest time. 2 The shoring beams and the fittings included in the TransSAFE system are simple to use. The installation and removal is done at lightning speed. 3 In case TransSAFE is not needed, the system can be stored easily on the side and takes up very little space. 1 2 3 Your advantages: flexible und light-weight versatile and fast optimal use of space Further information under: www.transsafe-.info 21
1 Transporter Securing of freight with textile shelfs in transporter General information TransSAFE is a textile shelf system consisting of shoring elements and nets. The load is secured to the front and rear by nets which are attached to six KIM 5x7 Airline shoring beams. The KIMs are positioned as close to the front, rear and center as possible. The shoring beams are tightly fixed into roof and floor ts. } Floor- and sidewall ts Airline t with flange The floor t is preferably fixed by professional bonding and additional screws to the body of the vehicle. Because of this, the distribution of the load will be evenly applied. The distance between the ts should be 615 mm in order to achieve an optimum ratio of aisle width to shelf depth. Please note, the floor ts available ex works are normally not compatible with our system due to the difference in the t gauge. } Roof t Airline t, standard, rectangular The roof t is fixed to the cross member of the roof construction. It must be connected with the bulkhead and rear door with appropriate bets. 22
} KIM 5x7 Airline Shoring beams The shoring beams won t twist within the Airline t. They allow flexibility due to the Airline milling along the sides of the beam. Each shoring beam has a blocking capacity of 650 dan (BC). This enables positive locking even for heavy loads. TRANSPORTER } TransSAFE nets Textile shelves The nets are fixed to the KIMs and to the sidewalls. Due to the fact that the nets can be installed freely, the optimal usage of available space is guaranteed. Each net can be loaded with up to a maximum of 300 kg. } TransSAFE straps Textile straps The straps are made of high tenacity polyester and are equipped with our KERL 500 and a high quality tensioning element. With the straps, additional parcels can be secured. 23
1 Transporter Components in detail Airline ts 100 6000 mm Airline roof ts 1 - Profile / Length 2 - Starting point 3 - Mounting holes 4 - Ends 5 - T cover / End caps Order code 12 95 P Weight: 1,43 kg/m 520377 Length xxxx mm ø20 Airline t standard rectangular P Weight: 0,90 kg/m 71206 Length xxxx mm Airline t with flange P Weight: 0,80 kg/m 71209 Length xxxx mm 24
SH Starting point Mounting holes 2 - Starting point 3 - Mounting holes 4 - Ends 5 - End cap / T cover Order code P P e.g.: X = 0 mm e.g.: X = 25 mm e.g.: P = 25 mm e.g.: P = 50 mm If not indicated otherwise, the starting dimension is X = 0 mm, pitch P = 25,0 mm. P-xx 3 - Mounting holes 4 - Ends 5 - End cap / T cover Order code S 5 S 6 S 8 N 4 N 5 N 6 D 5,5 D 6,6 D 8,5 M 5 M 6 5 / 10 5 / 10 W 90 90 90 120 120 120 D 11 13 17,2 10,1 12,0 13,0 10,0 d 5,5 6,6 9,0 4,2 5,05 6,7 5,5 6,6 8,5 5,0 Please select the type of mounting holes (S = Countersunk screw, N = Countersunk rivet, D = Cylindric hole, M = Internal thread) e.g.: S 5 TRANSPORTER Pitch of mounting holes 3 - Mounting holes 4 - Ends 5 - End cap / T cover Order code a2 = same pitch a2 - a... = individual pitch Please specify the pitch of the mounting holes a1 and a2 Please specify the pitch of the mounting holes a1, a2, a3, a4 etc. a1-xx / a2-xx Two-piece ts 4 - Ends 5 - End cap / T cover Order code Middle Please choose the division section: Middle Beginning and end Beginning and end Shape of ends 4 - Ends 5 - End cap / T cover Order code Please select the shape of the beginning of the t (max. radius or max. F2 = half of t width in mm) F2 F1 SL A / E straight A / E burred A / E R-xx A / E F1-xx F2-xx A / E SH-xx SL-xx T cover 5 - End cap / T cover Order code End caps Plastic end caps. Only in combination with straight ended ts (not compatible with 520377) T cover (not compatible with 320643 and 520624) End caps T cover } Sample order code Airline Flansch - 5800 - N 6 - a1-25/a2-75 - middle - A-straight - end caps 25
1 Transporter The set Load restraint with textile shelves TransSAFE set 1 - Product Order code Content of the set: 6 KIM 5x7 Airline shoring beams 7 nets, suitable for the respective vehicle type 8 TransSAFE straps 1 anchor plate Suitable for Mercedes-Benz Sprinter and Volkswagen Crafter with a 3665 mm wheelbase and high roof (load area length 3265 mm). With sidewall ts. Suitable for Mercedes-Benz Sprinter and Volkswagen Crafter with a 3665 mm wheelbase and high roof (load area length 4300 mm). With sidewall ts. TransSAFE is also available for further vehicle types. *) Please ask. 511280-10 511281-10 * 26
Combinations KIM 5x7 Airline 510574 KERL 500 310275 Cam buckle strap 511279-10 TRANSPORTER Airline roof t 520377 Airline t rectangular 71206 Airline t with flange 71209 KERL 500 310275 KERL 25 511229 Cam buckle strap 511279-10 Anchor plate 71106 27
allsafe JUNGFALK GmbH & Co. KG Gerwigstraße 31 D-78234 Engen Phone +49 (0)7733 5002-0 Fax +49 (0)7733 5002-47 E-Mail sales@allsafe-group.com www.allsafe-group.com 590436-11 We reserve the right to make changes 12.2016