SERIES W50 TECHNICAL CATALOGUE

SERIES TECHNICAL CATALOGUE

Heat-insulated building construction Series W 50 3 1 Catalogue cover 3 Catalogue pages Overview 4 Design Description 5 System Description 6 Installation Depths/Levels/Drainage Facilities 7 Statics Table 8 Statics Table 9 Statics Table 10 Statics Table 11 Statics Table 12 Dimensioning of Mullions and s 13 Predimensioning Table 14 Statics Predimensioning, Spar Spacing 80 cm 15 Statics Predimensioning, Spar Spacing 90 cm 16 Statics Predimensioning, Spar Spacing 100 cm 17 Statics Predimensioning, Spar Spacing 110 cm 18 Statics Predimensioning, Spar Spacing 120 cm 19 Calculation of the Thermal Conductivity Coefficient Ucw 20 Nominal Values of Thermal Conductivity Coefficient Uf 21 Profiles 22 Profiles 23 Profiles 24 Profiles 25 Profiles 26 Profiles 27 Profiles 28 Profiles 29 Profiles 30 Profiles 31 Profiles 32 Profiles 33 Profiles 34 Profiles 35 Profiles, pressure and cover profiles 36 Frame Inserts 37 Frame Inserts 38 Frame Inserts 39 Window Inserts 40 Auxiliary and connecting profiles 41 Variable angle profiles 42 Accessories 43 Accessories 44 Accessories 45 Accessories 46 Corner connectors 47 Corner connectors 48 Corner connectors 49 T-connection 50 T-connection 51 T-connection 52 T-connection 53 T-connection 54 T-connection 55 T-connection 56 T-connection 57 T-connection 58 T-connection 59 T-connection 60 T-connection 61 T-connection 62 T-connection 63 T-connection 64 T-connection 65 T-connection 66 T-connection 67 Reinforcement 68 Variable T-connection 69 Variable T-connection 70 Variable T-connection 71 Accessories 72 Accessories 73 Accessories 74 Screws 75 T-connection 76 Cutting Points 77 Drilling template 78 Drilling template 79 T-connection transom 80 Cutting point, horizontal 81 Installation of insulator PK 426 in sash area 82 Cut lengths 83 Facade connections 84 Cutting point 85 Cutting point 86 Cutting point 87 Cutting point 88 Cutting point 89 Cutting point 90 Cutting point 91 Cutting point 92 Cutting point 93 Cutting point 94 Cutting point 95 Cutting point 96 Section of A turning mode (45 o angle) 97 Section of A turning mode (60 o angle) 98 Cutting point, horizontal, below or above the window sash 99 Cutting point 100 Cutting point 101 Cutting point 102 Cutting point 103 Cutting point 104 Cutting point 105 Cutting point 106 Cutting point 107 Cutting point 108 Cutting point 109 Cutting point 110 Cutting point www.balkan.gr

4 Light alloy profile system for facades Design Description Facade: Thermal-insulated facade mullion-and-transom construction with disengaged transom profiles for optimum load transmission. The heat insulation, formed from the insulator profile, is integrated into the supporting inner profile over its full length by means of a special groove. Uf values to EN ISO 10077. Dimension values Uf,BW to DIN V 4108-4: 2002 Dimensions*: Statics: The glazing or the installation of insert elements such as e.g. windows or doors is made with pressure profiles screwed on from the outside. With a corresponding mullion formation (half mullions), the facade can be fitted with the concealed window sash. Cover profiles in various heights and forms are available for covering the pressure profiles. Mullion and transom profiles with 50 mm visible width. Installation depths available in graduated dimensions according to statics requirements from 80 mm to 200 mm. The design conforms in its statics to DIN 4113, DIN 1005 and unconditionally to the technical guidelines of the glass industry. * The installation depths indicated in the catalogue are reference dimensions for planning. The manufactured dimensions for frame and sash profiles lie 0.4 mm above the nominal dimensions in the catalogue, the glazing bar profiles 0.2 mm April 2009

System Description Design Description 5 1. The visible width of the facade profiles is 50 mm. 2. The installation depths of the mullion and transom profiles are designed in graduated dimensions according to statics requirements from 80 mm to 200 mm. Half mullions and half transoms to receive D, DK and tilting sashes while maintaining the mm outside visible width in the window area by concealed, integrated ashes. 3. Room-side hollow chambers for installation of special push-in profiles for securing and connection of the mullion profiles. 4. Facade mullion-and-transom constructions with disengaged mullion profiles for transom connection and hence for optimum load transmission. Sash available with clamped and bpnded glazing. 5. The glazing or the installation of insert elements such as e.g. windows or doors is made with pressure profiles screwed on from the outside. Glazings and panels with thicknesses from 24 to 38 mm can be installed using spacers and/or gasket profiles. The use of integrated window profiles in conjunction with half mullion or half transom profiles is possible. 6. The dry glazing is performed from inside and outside with EPDM gaskets. Ventilation of the glazing rabbet from the outside is effected via special ventilation channels. 7. Draining is effected under control via drainage levels or the mullion or transom profiles. 8. All connecting and retaining parts of the facade construction are made from aluminium or stainless steel. 9. The pressure profiles are screwed on through the insulator into preformed screw channels of the mullion and transom profiles with a maximum spacing of 25 cm. 10. The pressure profiles are covered uding cover profiles in various heights and forms from 12 to 30 mm. The vertical cover profiles should stand higher than the horizontal cover profiles. 11. All profiles can be anodised or painted. 12. The heat insulation, formed from the insulator profile, is integrated into the supporting inner profile over its full length by means of a special groove. The Uf values were determined in accordance with DIN EN ISO 10077-2. Dimensioning values Uf, BW to DIN V 4108-4: 2002. 13. The outer cover profiles at the facade junction points have a visible width corresponding to the viewing angles. 14. The aluminium profiles extruded dimensionally to DIN EN 12020 are made of the alloy DIN 6060 (AIMgSi 0.5 F-22) in anodised quality. 15. The design conforms in its statics to DIN 4113, DIN 1005 and unconditionally to the technical guidelines of the glass industry. 16. All loads occurring must be reliably transmitted to the building. 17. The Code of Practice for the Processor in our latest main catalogue must be observed for the use and processing of our design. www.balkan.gr

6 Installation Depths/Levels/Drainage Installation Depths/Levels/Drainage Mullion Level 3 Level 1 Level 2 shown in reduced size Drawn rotated through 90 o Mullion, Vertical Level 3, Vertical Level 1, Horizontal Level 2 April 2009

Statics Table, Profile Series Statics Table 7 Mullion Level 3, Vertical Profile No.: Ix cm 4 min Wx cm 3 ex cm2 Iy cm 4 min Wy cm 3 ey cm2 AH550-5114080 W51 14080 62.76 14,14 4,26 22,16 8,86 2,50 AH550-5114100 W51 14100 107,53 19,39 5,15 26.35 10,54 2,50 AH550-5114120 W51 14120 167,14 25,20 6,06 30,53 12,21 2,50 AH550-5114140 W51 14140 243,04 31,53 6,99 34,71 13,88 2,50 AH550-5114160 W51 14160 352,81 40,72 8,03 43,47 17,39 2,50 AH550-5114180 W51 14180 553,02 58,90 9,31 56,17 22,47 2,50 AH550-5114200 W51 14200 790,30 74,78 10,13 66,36 26,54 2,50 AH550-5115080 W51 15080 39,89 8,17 3,81 5,25 2,41 1,30 AH550-5115120 W51 15120 111,40 15,30 5,42 6,24 2,72 1,19 AH550-5115160 W51 15160 249,00 26,50 7,30 7,35 3,08 1,09 AH550-5113080 W51 13080 83,60 17,85 4,01 83,60 17,85 4,01 www.balkan.gr

8 Statics Table, Profile Series Statics Table Level 2, Horizontal Art Nr.: Ix cm 4 min Wx cm 3 ex cm2 Iy cm 4 min Wy cm 3 ey cm2 AH550-5122011 W51 22011 0,61 0,49 0,54 4,46 1,78 2,50 AH550-5122024 W51 22024 2,85 1,60 1,27 8,70 3,48 2,50 AH550-5122039 W51 22039 9,09 3,90 2,21 11,84 4,73 2,50 AH550-5122054 W51 22054 20,07 6,43 2,92 14,84 5,99 2,50 AH550-5122079 W51 22079 50,74 11,12 3,99 20,20 8,08 2,50 AH550-5122099 W51 22099 101,07 18,97 5,22 25,22 10,09 2,50 AH550-5122119 W51 22119 157,44 24,63 6,16 29.41 11.76 2.50 AH550-5122139 W51 22139 229,37 30,82 7,10 33.59 13.43 2.50 AH550-5122159 W51 22159 334,15 39,76 8,14 42.38 16.95 2.50 Level 1, Vertical Profile No.: Ix cm 4 min Wx cm 3 ex cm2 Iy cm 4 min Wy cm 3 ey cm2 AH550-5121077 W51 21077 55,84 13,01 4,11 20,64 8,25 2,50 Mullion Adaptor for Variable Angles Profile No.: Ix cm 4 min Wx cm 3 ex cm2 Iy cm 4 min Wy cm 3 ey cm2 AH550-5113001 2,8731 1,545 1,21 9,0602 3,62 2,15 April 2009

Statics Table, Profile Series Statics Table 9, Frames, Sashes Profile No.: Ix cm 4 min Wx cm 3 ex cm2 Iy cm 4 min Wy cm 3 ey cm2 AH550-5122080 W51 22080 41,10 8,53 3,88 5,10 2,35 1,30 AH550-5150053 W51 50053 13,72 4,65 2,45 5,37 2,14 1,69 AH550-5150080 W51 50080 26,22 5,99 3,62 6,11 2,97 1,44 AH550-5150003 9,18 2,78 2,06 48,8 9 1,23 AH275-280 10,51 3,85 2,15 50,3 9,13 1,29 AH550-5150015 Push-in profiles for mullions Profile No.: Ix cm 4 min Wx cm 3 ex cm2 Iy cm 4 min. Wy cm 3 ey cm 2 AH550-5182080 W51 82080 33.81 10.50 3.05 20.78 9.19 2.26 AH550-5182100 W51 82100 68.81 16.09 3.99 26.13 11.56 2.26 AH550-5182120 W51 82120 120.02 22.56 4.95 31.48 13.93 2.26 AH550-5182140 W51 82140 189.88 29.88 5.91 36.83 16.30 2.26 AH550-5182160 W51 82160 280.77 38.04 6.89 42.19 18.66 2.26 AH550-5182180 429.49 51.86 2.22 22.32 10.05 8.28 AH550-5182200 571.37 62.13 2.20 24.17 10.99 9.19 www.balkan.gr

10 Statics Table, Profile Series Statics Table Pressure plate and cover profiles Profile No.: Dev. anod. [mm] Dev. elox. [mm] AH550-5051006 51006 155 50 AH 550-50 57010 57010 182 - AH550-5061012 61012 147 74 AH550-5061015 61015 159 80 AH550-5061020 61020 177 90 AH550-5067030 67030 248 155 AH550-5063098 293 206 AH550-5113002 256 58 AH550-5113003 218 49 AH550-5113004 354 81 AH550-5113005 104 29 AH550-5113006 83 11 Pressure plate and cover profiles Profile No.: Dev. anod. [mm] Dev. elox. [mm] AH550-9071008 W90 71008 68 53 AH550-9071010 W90 71010 76 45 April 2009

Statics Table, Profile Series Statics Table 11 Connectors profiles for structural Profile No.: Dev. anod. [mm Dev. elox. [mm] AH550-901 119 - AH550-902 114 - AH550-903 97 - Connectors profiles Profile No.: Dev. anod. [mm Dev. elox. [mm] AH550-5184045 215 - AH550-5184044 214 - AH550-5184046 217 - AH550-5184346 216 - AH550-5182000 974 - AH550-5184001 192 - AH550-5184002 98 - Glass support Profile No.: Dev. anod. [mm Dev. elox. [mm] AH550-5156042 W51 56042 AH550-5156053 W51 56053 94-123 - AH550-5150001 54 - AH550-5150002 83 - www.balkan.gr

12 Dimensioning of Mullions and s Statics Table Loading width: The loading width c1 or c2 is determined by half the fields adjacent to the mullions or transoms. Load case: A freely supported girder on two supports with trapezoidal or triangular load is assumed as the load case. The division of the load-bearing surface is effected by halving the angles. Admissible bending: The general rule is fz ul. = q/300 I (DIN 18056) The insulating glazing manufacturers regard this as the maximum bending between the support points of support spacing I, but limit the admissible bending in the partial area (bending between the supporting points of the largest part-area) to fzul. = 1/300 I = 0,8 cm. Support width 1 (cm) Mullion spacing Loading width Mullion spacing Load assumptions: (DIN 1055 Part 4) Dynamic pressure q = 0,5 kn/m 2 (height above ground = 0-8 m) Dynamic pressure q = 0,8 kn/m 2 (height above ground = 8-20 m) Dynamic pressure q = 1,1 kn/m 2 (height above ground = 20-10m) Pressure coefficient cp = 0,8 + 1/4 = 1,0 Wind pressure w = q c p (kn/m2) Material strength specifications of the Al alloy AlMgSi 0.5 F22 (DIN 4113) Minimum tensile strength β z = 22 kn/cm 2 Minimum yield strength d 0,2 = 16 kn/cm 2 Admissible strain (main load H): d zul = 95 N/mm 2 Modulus of elasticity E = 7000 kn/cm 2 Application of tables I and II For mullions or transoms of single-pane fields Example A use Table I For mullions or transoms of multi-pane fields Example Β use Table II if all the part-areas are = 240 cm in size. In Example C the largest partial area of the mullion is dimensioned as 320 cm. As this is larger than 240 cm, f zul. = 0,8 cm or fzul. = lp/ 0,8 I = 320/0,8 I = 1/400 I applies for this area. This admissible bending of 1/400 I of the partial area applies to the whole mullion length of 460cm. In order to determine the necessary inertia moment Ix, the value from Table II opposite must first be divided by 300 and then multiplied by 400. Support width 1 (cm) Support width 1 (cm) = 460 cm Support width 1 (cm) = 460 cm Mullion spacing Mullion spacing Mullion spacing Mullion spacing Mullion spacing Mullion spacing April 2009

Predimensioning Table 13 Table for determining the necessary inertia moments Ix req. [cm 4 ] for aluminium = (E= 7000 kn/m 2 ) Load case: Freely supported girder on two supports with trapezoidal or triangular load. The values indicated serve only for profile predimensioning and are no alternative to an examinable statics calculation. Table I Bending f = 1/300 I 0,8 cm For mullions or transoms Single-paned fields, use Table I 180 3,2 4,7 6,0 7,2 8,1 8,8 9,2 9,4 190 3,8 5,5 7,1 8,5 10,6 10,6 11,3 11,6 200 4,4 6,5 8,4 10,1 12,7 12,7 13,6 14,1 14,3 210 5,1 7,5 9,7 11,8 15,0 15,0 16,2 16,9 17,3 220 5,9 8,6 11,3 13,7 17,6 17,6 19,0 20,1 20,7 20,9 230 6,7 9,9 12,9 15,7 20,4 20,4 22,2 23,5 24,5 24,9 240 7,6 11,3 14,8 18,0 23,5 23,5 25,6 27,3 28,6 29,4 29,6 250 9,0 13,3 17,4 21,3 27,9 27,9 30,6 32,8 34,5 35,7 36,3 260 10,5 15,6 20,5 25,0 33,0 33,0 36,3 39,1 41,3 42,9 43,9 44,2 270 12,2 18,2 23,9 29,2 38,7 38,7 42,7 46,2 49,0 51,1 52,6 53,3 280 14,2 21,0 27,7 33,9 45,1 45,1 49,9 54,1 57,6 60,4 62,4 63,6 64,0 290 16,3 24,2 31,9 39,2 52,3 52,3 58,0 63,0 67,3 70,8 73,5 75,3 76,2 300 18,7 27,8 36,6 45,0 60,3 60,3 67,0 73,0 78,2 82,5 85,9 88,4 89,9 90,4 310 21,3 31,7 41,8 51,5 69,2 69,2 77,0 84,0 90,2 95,5 99,8 103 105 106 320 24,2 36,1 47,6 58,6 78,9 78,9 88,0 96,3 104 110 115 119 122 124 125 330 27,4 40,8 53,9 66,4 89,7 89,7 100 110 118 126 132 137 141 144 145 340 30,9 46,0 60,8 75,0 102 102 114 125 135 143 151 157 163 166 168 169 350 34,7 51,7 68,3 84,4 114 114 128 141 152 163 172 179 186 190 194 195 360 38,9 57,9 76,6 94,6 129 129 144 159 172 184 195 204 211 217 221 224 225 370 43,4 64,7 85,5 106 144 144 162 178 193 207 219 230 239 247 252 256 258 380 48,3 72,0 95,3 118 161 161 180 199 216 232 246 259 270 279 286 291 294 295 390 53,6 79,9 106 131 179 179 201 222 241 259 279 290 303 314 322 329 333 335 400 59,3 88,5 117 145 198 198 223 247 269 289 308 324 339 352 362 370 376 380 381 410 65,5 97,7 129 160 219 219 247 273 298 321 342 361 378 393 405 415 423 428 431 420 72,1 108 143 177 242 242 273 302 330 355 379 401 420 438 452 464 474 481 485 430 79,2 118 157 194 267 267 301 333 364 393 419 444 466 486 503 517 529 538 544 440 85,9 130 172 213 293 293 330 366 400 433 463 490 515 538 557 574 588 599 607 450 95,0 142 188 234 321 321 362 402 440 475 509 540 568 594 616 636 652 666 676 460 104 155 206 255 351 351 397 440 482 521 558 593 625 654 679 702 721 737 750 470 113 169 224 279 383 383 433 481 527 571 612 650 685 718 747 773 796 814 830 480 123 184 244 303 417 417 472 525 575 623 668 711 750 787 820 849 875 897 915 490 134 200 265 330 454 454 514 571 626 679 729 776 820 860 897 930 960 985 1007 500 145 217 288 358 493 493 558 620 681 739 793 845 894 939 980 1017 1051 1080 1105 510 157 235 312 387 534 534 605 673 739 802 862 919 972 1022 1068 1110 1148 1181 1210 520 170 254 337 419 578 578 655 729 800 869 935 997 1056 1111 1162 1209 1251 1288 1321 530 183 274 364 452 624 624 707 788 866 941 1012 1080 1145 1205 1262 1313 1361 1403 1440 540 197 295 392 488 674 674 763 851 935 1016 1094 1169 1239 1305 1367 1425 1477 1525 1567 550 212 318 422 525 726 726 822 917 1008 1097 1181 1262 1339 1411 1479 1543 1601 1654 1701 560 228 341 454 564 780 780 885 987 1086 1181 1273 1361 1445 1524 1598 1668 1732 1791 1844 570 245 357 487 606 838 838 951 1061 1168 1271 1370 1465 1556 1643 1724 1800 1871 1936 1995 580 263 393 522 650 900 900 1021 1139 1254 1365 1472 1576 1674 1768 1857 1940 2017 2089 2154 590 281 421 559 696 964 964 1094 1221 1345 1465 1580 1692 1799 1900 1997 2087 2172 2251 2323 600 301 450 598 745 1032 1032 1171 1308 1440 1569 1694 1814 1930 2040 2144 2243 2336 2422 2501 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 Determination of the necessary inertia moments The determination is performed in the following order: 1. Determination of support width I in cm. 2. Determination of load width c1 and c2 in cm. 3. Determination of inertia moment Ix erf. for load width c1 according to corresponding Table I or II. 4. Determination of inertia moment Ix erf. for load width c2 according to corresponding Table I or II. 5. Addition of the necessary inertia moments determined under 3 and 4. 6. Multiplication of the sum of the necessary inertia moments by the factorfor the wind pressure. p Conversion factors 9,4 9,2 8,8 8,1 7,2 6 4,7 3,2 180 Support width 1 (cm) Support width 1 (cm) 12 11 11 9,7 8,5 7,1 5,5 3,8 190 14 14 14 13 12 10 8,4 6,5 4,4 200 17 17 16 15 14 12 9,7 7,5 5,1 210 21 21 20 19 18 15 14 11 8,6 5,9 220 25 25 24 22 20 18 16 13 9,9 6,7 230 30 29 29 27 26 24 21 18 15 11 7,6 240 35 34 33 32 29 27 24 20 17 13 8,6 250 41 41 40 38 36 34 31 27 23 19 14 9,7 260 47 47 45 44 41 38 34 30 26 21 16 11 270 55 55 54 52 49 46 43 39 34 29 24 18 12 280 63 62 61 59 56 52 48 43 38 32 26 20 14 290 72 72 71 69 66 63 58 54 48 42 36 29 22 15 300 82 82 80 77 74 70 65 60 54 47 40 32 25 17 310 94 93 92 90 86 83 78 72 66 59 52 44 36 27 18 320 106 105 103 100 96 92 86 80 73 65 57 48 39 30 20 330 119 119 117 115 111 107 101 95 88 80 72 63 53 43 33 22 340 134 133 131 127 123 118 112 105 97 88 79 68 63 47 36 24 350 150 149 148 145 141 136 130 123 115 106 96 86 75 69 51 39 26 360 167 166 164 160 155 149 142 134 125 115 105 93 81 74 56 42 28 370 186 186 184 180 176 170 164 156 147 137 126 114 101 88 81 60 46 31 380 206 205 202 198 193 186 179 170 160 149 137 124 110 96 87 65 49 33 390 229 228 226 222 217 211 203 195 185 173 161 148 134 119 103 94 70 53 36 400 252 251 248 243 237 230 221 211 200 188 174 160 145 128 111 101 76 57 38 410 277 275 271 265 258 250 240 229 217 203 188 173 156 138 120 109 82 62 41 420 303 300 295 289 281 271 260 248 234 219 203 186 168 149 129 116 88 66 44 430 331 327 321 313 304 293 281 267 252 236 218 200 180 160 138 125 94 71 47 440 360 355 348 339 329 317 303 288 271 254 235 214 193 171 148 133 100 76 51 450 391 385 376 365 354 341 326 309 291 272 251 230 207 183 159 142 107 81 54 460 424 416 406 395 382 367 350 332 312 291 269 246 221 196 169 152 115 86 58 470 458 449 437 425 410 393 375 355 334 312 288 262 236 209 181 161 122 92 62 480 493 483 470 456 439 421 402 380 357 333 307 280 252 222 192 172 130 98 66 490 530 518 504 488 470 451 429 406 381 355 327 298 268 237 204 182 138 104 70 500 569 556 540 522 503 481 458 432 406 377 348 317 285 251 217 193 147 110 74 510 610 595 577 558 536 513 487 460 432 401 369 336 302 267 230 205 155 117 78 520 652 635 616 595 571 546 518 489 458 426 392 357 320 283 244 217 165 124 83 530 696 678 656 633 608 580 551 519 486 452 416 378 339 299 258 229 174 131 88 540 742 722 699 673 646 616 584 551 515 478 440 400 359 317 273 242 184 139 93 550 790 767 742 715 685 653 619 583 546 506 465 423 379 334 289 255 194 146 98 560 840 815 788 758 726 692 655 617 577 535 492 447 400 353 305 269 205 154 103 570 892 864 835 803 768 732 693 652 609 565 519 471 422 372 321 283 216 163 109 580 945 916 884 849 812 773 732 688 643 596 547 497 445 392 338 298 228 171 114 590 1001 969 934 897 858 816 772 726 678 628 576 523 469 413 356 239 239 180 120 600 They are calculated for a wind pressure of 0,5 kn/m². In the case of other wind pressures, the inertia moment determined must be multiplied by the corresponding factor. 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 Height above ground 0-8m 8-20m 20-100m Dynamic pressure q 0,5 kn/m2 0,8 kn/m2 1,1 kn/m2 Pressure coefficient c p 1,0 1,0 1,0 Wind pressure w = q c p 0,5 kn/m 2 0,8 kn/m 2 1,1 kn/m 2 For mullions or transoms of multi-pane fields, use Table II if all the partareas are 240 cm in size. Factor 1,0 1,6 2,2 Table II Bending f = 1/300 I Support width I (cm) I= Support width in cm C 1 = Load width in cm C 2 = Load width in cm T p 0 d b Load width a [cm] Load width a [cm] www.balkan.gr

14 Statics Predimensioning, Spar Spacing 80 cm Table for determination of the necessary inertia moments Ix req. [cm 4 ] for spars or mullions of a shed roof or inclined facade of aluminium profiles (E=7000 kn/m 2 ) Load case: Freely supported girder on two supports, trapezoidal or triangular load Bending max f= 1/300* I (values in table apply for max. edge length of individual glazings = 240 cm) Typical snow load So= 0,75 kn/m 2 Dead weight g=0.47 kn/m 2 Vertical individual live load F=1kN Conversion factor for increased snow loads with roof angles up to 60 o (approx. values) For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.2 For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.4 Spar spacing = 80 cm Dynamic pressure q = 0,5 kn/m 2 (building height 0-8m) Dynamic pressure q = 0,8 kn/m 2 (building height 8-20m) Dynamic pressure q = 1,1 kn/m 2 (building height 20-100m) 80 a Roof angle 80 b Roof angle 80 c Roof angle dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o 140 25 21 20 19 17 16 14 12 8 6 5 150 29 25 24 22 20 19 17 14 10 8 7 160 34 29 27 26 24 22 19 17 11 10 8 170 39 33 32 30 27 25 22 19 13 12 10 180 44 38 36 34 31 28 25 22 16 14 12 190 50 43 41 38 35 32 29 25 19 17 14 200 57 49 46 43 40 36 33 28 22 19 17 210 64 55 52 49 45 41 37 32 26 23 19 220 71 62 58 54 50 46 41 37 30 26 23 230 79 68 65 61 56 51 47 43 34 30 26 240 88 76 72 67 62 58 54 49 39 34 30 250 97 86 80 74 68 66 61 55 44 39 33 260 106 97 90 84 77 75 69 63 50 44 38 270 117 109 102 94 87 84 77 70 56 49 42 280 127 122 114 105 97 94 86 79 63 55 47 290 139 135 126 117 108 105 96 88 70 61 53 300 154 150 140 130 119 116 107 97 77 68 59 310 170 166 155 144 132 128 118 107 86 75 65 320 187 183 171 158 146 141 130 118 94 83 71 330 206 201 188 174 160 155 143 130 104 91 78 340 225 220 206 191 175 170 156 142 113 100 86 350 246 240 225 208 191 186 171 155 124 109 94 360 268 262 245 227 208 202 186 169 135 119 102 370 292 285 266 247 226 220 202 184 147 129 111 380 316 309 288 267 245 238 219 199 159 140 120 390 342 334 312 289 266 258 237 216 172 152 130 400 369 360 337 312 287 278 256 233 186 164 141 410 398 388 363 337 309 300 276 251 200 176 152 420 428 418 391 362 332 323 297 270 215 190 163 430 460 449 419 389 357 347 319 290 231 204 175 440 493 481 450 417 383 372 342 311 248 218 188 450 528 515 481 446 410 398 366 333 266 234 201 460 564 550 514 477 438 425 391 356 284 250 215 470 602 587 549 509 467 454 417 380 303 267 229 480 642 626 585 542 498 483 445 405 323 284 244 490 683 666 623 577 530 514 473 431 343 302 260 500 726 708 662 614 563 547 503 458 365 321 276 510 771 752 702 651 598 581 534 486 388 341 293 520 817 797 745 691 634 616 566 515 411 362 311 530 865 844 789 732 672 652 600 546 435 383 329 540 916 893 835 774 711 690 635 578 461 406 348 550 968 944 882 818 751 729 671 611 487 429 368 560 1022 997 932 864 793 770 708 645 514 453 389 570 1078 1052 983 911 837 812 747 680 542 477 410 580 1136 1108 1036 960 882 856 787 717 571 503 432 590 1196 1167 1090 1011 928 901 829 755 602 530 455 600 1258 1227 1147 1064 977 948 872 794 633 557 479 140 25 21 20 19 17 16 14 12 10 9 9 150 29 25 24 22 20 19 17 15 13 12 11 160 34 29 27 26 24 22 20 19 16 15 13 170 39 33 32 30 27 26 24 23 19 18 16 180 44 38 36 34 31 31 29 27 23 21 19 190 50 43 41 38 36 37 34 32 27 25 23 200 57 49 46 43 42 43 41 38 32 30 27 210 64 55 52 49 49 50 47 44 37 34 31 220 71 62 58 56 57 58 55 51 43 40 36 230 79 70 67 64 66 67 63 58 50 46 41 240 88 80 76 73 75 76 71 67 57 52 47 250 97 91 86 83 85 86 81 76 64 59 54 260 106 102 97 94 96 97 91 85 73 67 60 270 117 115 109 105 107 109 103 96 82 75 68 280 130 129 122 118 120 122 115 107 91 84 76 290 145 143 136 131 134 136 128 119 101 93 84 300 160 159 151 145 148 151 142 132 113 103 94 310 177 176 167 161 164 167 157 146 124 114 104 320 195 194 184 177 181 184 173 161 137 126 114 330 215 213 202 195 199 202 190 177 151 138 125 340 235 233 222 213 217 221 208 194 165 151 137 350 257 254 242 233 237 242 227 212 180 165 150 360 280 277 264 254 259 263 247 231 196 180 163 370 304 301 286 276 281 286 269 251 213 196 178 380 330 327 311 299 305 310 291 272 231 212 193 390 357 353 336 323 330 336 315 294 250 230 208 400 385 382 363 349 356 336 340 317 270 248 225 410 415 411 391 376 384 391 367 342 291 267 242 420 447 442 421 405 413 420 395 368 313 288 261 430 480 475 452 435 444 452 424 395 336 309 280 440 514 509 484 466 475 484 454 424 361 331 300 450 550 545 519 499 509 518 486 453 386 354 321 460 588 583 554 533 544 554 520 485 413 379 343 470 628 622 591 569 580 591 555 517 440 404 367 480 669 663 630 606 619 630 591 551 469 431 391 490 712 705 671 645 658 670 629 587 499 458 416 500 757 750 713 686 700 713 669 624 531 487 442 510 803 796 757 728 743 756 710 662 564 517 469 520 852 844 803 772 788 802 753 702 598 548 497 530 902 894 850 818 834 850 798 744 633 581 527 540 955 946 900 865 883 899 844 787 670 615 557 550 1009 999 951 915 933 950 892 831 708 650 589 560 1065 1055 1004 966 985 1003 942 878 747 686 622 570 1124 1113 1059 1019 1039 1058 993 926 788 723 656 580 1184 1173 1116 1074 1095 1115 1047 976 831 762 692 590 1247 1235 1175 1130 1153 1174 1102 1028 875 803 728 600 1312 1299 1236 1189 1213 1235 1159 1081 920 844 766 140 25 21 20 19 17 17 16 15 13 13 12 150 29 25 24 22 21 21 20 19 17 16 15 160 34 29 27 26 25 26 25 24 21 20 18 170 39 33 32 30 31 32 30 29 25 24 22 180 44 38 36 35 37 38 36 34 30 28 26 190 50 43 41 42 44 45 43 41 36 34 31 200 57 49 47 49 51 53 51 48 42 40 37 210 64 56 55 57 60 62 59 56 49 46 43 220 71 65 63 66 69 72 68 64 57 53 50 230 79 74 72 76 79 82 78 74 65 61 57 240 88 84 83 87 90 94 89 84 74 70 65 250 97 96 94 98 102 106 101 96 84 79 74 260 108 108 106 111 116 120 114 108 95 89 83 270 121 121 119 124 130 135 128 121 107 100 93 280 135 136 133 139 145 151 143 136 120 112 104 290 151 151 148 155 162 168 160 151 133 125 116 300 167 168 164 172 179 186 177 167 148 138 129 310 185 185 181 190 198 206 196 185 163 153 142 320 204 204 200 209 218 227 216 204 180 169 157 330 224 224 220 230 240 249 237 224 198 185 172 340 245 246 240 252 263 273 259 245 216 203 189 350 267 268 263 275 287 298 283 268 236 222 206 360 291 292 286 300 312 325 309 292 257 241 225 370 317 318 311 326 340 353 335 317 280 262 244 380 343 345 337 353 368 383 364 344 303 284 265 390 372 373 365 382 398 414 393 372 328 308 286 400 401 403 394 412 430 447 425 402 355 332 309 410 432 434 425 445 464 482 458 433 382 358 333 420 465 467 457 478 499 518 493 466 411 385 359 430 500 501 490 514 536 557 529 500 441 414 385 440 536 537 526 551 574 597 567 536 473 444 413 450 573 575 563 589 615 639 607 574 507 475 442 460 613 615 601 630 657 683 649 613 541 507 472 470 654 656 642 672 701 728 692 655 578 542 504 480 697 699 684 716 747 776 738 698 616 577 537 490 742 744 728 762 795 826 785 743 655 614 572 500 788 791 774 810 845 878 835 789 696 653 608 510 837 840 822 860 897 932 886 838 739 693 645 520 887 890 871 912 951 989 940 889 784 735 684 530 940 943 923 966 1008 1047 995 941 830 778 724 540 994 998 976 1022 1066 1108 1053 996 879 824 766 550 1051 1055 1032 1080 1127 1171 1113 1052 929 871 810 560 1110 1114 1089 1141 1190 1236 1175 1111 981 919 855 570 1171 1175 1149 1203 1255 1304 1239 1172 1034 970 902 580 1234 1238 1211 1268 1323 1374 1306 1235 1090 1022 951 590 1299 1303 1275 1335 1393 1447 1375 1301 1148 1076 1001 600 1366 1371 1341 1405 1465 1522 1447 1368 1207 1132 1053 Column spasing 1(cm) Column spasing 1(cm) Column spasing 1(cm) April 2009

Statics Predimensioning, Spar Spacing 90 cm 15 Table for determination of the necessary inertia moments Ix req. [cm 2 ] for spars or mullions of a shed roof or inclined facade of aluminium profiles (E=7000 kn/m 2 ) Load case: Freely supported girder on two supports, trapezoidal or triangular load Bending max f= 1/300* I (values in table apply for max. edge length of individual glazings = 240 cm) Typical snow load So= 0,75 kn/m 2 Dead weight g=0.47 kn/m 2 Vertical individual live load F=1kN Conversion factor for increased snow loads with roof angles up to 60 o (approx. values) For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.2 For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.4 Spar spacing = 90 cm Dynamic pressure q = 0,5 kn/m 2 (building height 0-8m) Dynamic pressure q = 0,8 kn/m 2 (building height 8-20m) Dynamic pressure q = 1,1 kn/m 2 (building height 20-100m) 90 a Roof angle 90 b Roof angle 90 c Roof angle dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o 140 25 21 20 19 17 16 14 12 8 7 5 150 29 25 24 22 20 19 17 14 10 8 7 160 34 29 27 26 24 22 19 17 12 11 9 170 39 33 32 30 27 25 22 19 15 13 11 180 44 38 36 34 31 28 25 22 17 15 13 190 50 43 41 38 35 32 29 26 21 18 16 200 57 49 46 43 40 37 34 31 24 22 18 210 64 55 52 49 45 43 39 36 29 25 22 220 71 64 60 56 51 49 46 41 33 29 25 230 79 74 69 64 59 57 52 48 38 33 29 240 88 84 79 73 67 65 60 54 43 38 33 250 98 95 89 83 76 74 68 62 49 43 37 260 110 108 101 93 86 83 77 70 56 49 42 270 124 121 113 105 96 94 86 78 62 55 47 280 139 136 127 117 108 105 96 88 70 62 53 290 155 151 141 131 120 117 107 98 78 69 59 300 172 168 157 145 133 129 119 108 86 76 65 310 190 185 173 161 148 143 132 120 96 84 72 320 209 204 191 177 163 158 145 132 105 93 80 330 230 225 210 195 179 173 160 145 116 102 88 340 252 246 230 213 196 109 175 159 127 112 96 350 276 269 251 233 214 208 191 174 139 122 105 360 300 293 274 254 233 226 208 189 151 133 114 370 326 318 298 276 253 246 226 206 164 145 124 380 354 345 323 299 275 267 245 223 178 157 135 390 383 374 349 324 297 289 266 242 193 170 146 400 414 404 377 350 321 312 287 261 208 183 157 410 446 435 407 377 346 336 309 281 224 198 170 420 480 468 438 406 373 362 333 303 241 213 183 430 516 503 470 436 400 388 357 325 259 228 196 440 553 539 504 467 429 416 383 349 278 245 210 450 592 577 540 500 459 446 410 373 298 262 225 460 633 617 577 535 491 477 439 399 318 280 241 470 675 659 616 571 524 509 468 426 340 299 257 480 720 702 656 608 559 542 499 454 362 319 274 490 766 747 698 646 595 577 531 483 385 339 291 500 814 794 742 688 632 613 565 514 410 361 310 510 865 843 788 731 671 651 599 545 435 383 329 520 917 895 836 775 712 691 636 578 461 406 349 530 971 948 885 821 754 732 673 613 489 430 370 540 1028 1003 937 869 798 774 712 648 517 455 391 550 1086 1060 990 918 843 818 753 685 546 481 413 560 1147 1119 1046 970 890 864 795 724 577 508 436 570 1210 1181 1103 1023 939 912 839 763 609 536 460 580 1275 1244 1163 1078 990 961 884 805 642 565 485 590 1343 1310 1224 1135 1042 1012 931 847 675 595 511 600 1413 1378 1288 1194 1097 1064 979 891 711 626 538 140 25 21 20 19 17 16 14 13 11 10 9 150 29 25 24 22 20 19 18 16 14 13 12 160 34 29 27 26 24 23 22 20 17 16 14 170 39 33 32 30 28 28 27 25 21 19 18 180 44 38 36 34 33 34 32 30 25 23 21 190 50 43 41 39 40 41 38 35 30 28 25 200 57 50 48 46 47 48 45 42 36 33 30 210 64 59 56 54 55 56 52 49 41 38 35 220 71 68 64 62 63 64 60 56 48 44 40 230 79 78 74 71 73 74 70 65 55 51 46 240 90 89 85 81 83 85 79 74 63 58 52 250 102 101 96 92 94 96 90 84 72 66 60 260 115 114 109 104 107 108 102 95 81 74 67 270 129 128 122 117 120 122 114 107 91 83 76 280 145 143 137 131 134 136 128 119 102 93 85 290 161 160 152 146 149 152 143 133 113 104 94 300 179 177 169 162 166 169 158 148 126 115 105 310 198 196 187 180 183 187 175 163 139 128 116 320 218 216 206 198 202 206 193 180 153 141 128 330 240 238 226 218 222 226 212 198 168 154 140 340 263 260 248 238 243 248 232 217 184 169 154 350 287 285 271 260 266 270 254 237 201 185 168 360 313 310 295 284 290 295 277 258 220 202 183 370 340 337 321 309 315 320 301 280 239 219 199 380 369 366 348 335 341 348 326 304 259 238 216 390 400 396 376 362 369 376 353 329 280 257 233 400 431 427 407 391 399 406 381 356 303 278 252 410 465 461 438 422 430 438 411 383 326 299 272 420 500 469 472 454 463 471 442 412 351 322 292 430 538 532 507 487 497 506 475 443 377 346 314 440 576 571 543 522 533 543 509 475 404 371 337 450 617 611 581 559 571 581 545 508 433 397 360 460 660 653 621 598 610 621 583 543 463 425 385 470 704 697 663 638 651 663 622 580 494 453 411 480 750 743 707 680 694 706 663 618 526 483 438 490 799 791 753 724 739 752 706 658 560 514 466 500 849 841 800 770 785 799 750 700 596 547 496 510 901 893 849 817 834 849 797 743 632 580 526 520 956 947 901 867 884 900 845 788 671 615 528 530 1013 1003 954 918 936 953 895 834 710 652 591 540 1071 1061 1010 971 991 1009 947 883 752 690 626 550 1133 1122 1067 1027 1047 1066 1001 933 794 729 661 560 1196 1185 1127 1084 1106 1126 1057 986 839 770 698 570 1262 1250 1189 1144 1167 1188 1115 1040 885 812 737 580 1330 1317 1253 1205 1230 1252 1175 1096 933 856 776 590 1400 1387 1319 1269 1295 1318 1238 1154 982 901 818 600 1473 1459 1388 1335 1362 1387 1302 1214 1033 948 860 140 25 21 20 19 18 18 18 17 15 14 13 150 29 25 24 22 22 23 22 21 18 17 16 160 34 29 27 26 28 29 27 26 23 21 20 170 39 33 32 32 34 35 33 31 28 26 24 180 44 38 37 39 40 42 40 38 33 31 29 190 50 45 44 46 48 50 47 45 40 37 35 200 57 53 52 54 57 59 56 53 47 44 41 210 64 62 60 63 66 69 65 62 54 51 47 220 71 72 70 73 76 79 75 71 63 59 55 230 82 82 80 84 88 91 87 82 72 68 63 240 94 94 92 96 100 104 99 94 83 78 72 250 106 107 104 109 114 118 113 106 94 88 82 260 120 120 118 123 129 134 127 120 106 99 93 270 135 135 132 139 145 150 143 135 119 112 104 280 151 151 148 155 162 168 160 151 133 125 116 290 168 169 165 173 180 187 178 168 149 139 130 300 187 187 183 192 200 208 198 187 165 155 144 310 206 207 203 212 221 230 219 207 182 171 159 320 227 228 223 234 244 253 241 228 201 188 175 330 250 251 245 257 268 279 265 250 221 207 193 340 274 275 269 282 294 305 290 274 242 227 211 350 299 300 294 308 321 333 317 300 264 248 231 360 326 327 320 335 350 363 345 327 288 270 251 370 354 356 348 364 380 395 375 355 313 294 273 380 384 386 377 395 412 428 407 385 340 318 296 390 416 418 409 428 446 464 441 417 368 345 321 400 449 451 441 462 482 501 476 450 397 372 346 410 484 486 476 498 519 540 513 485 428 401 373 420 521 523 512 536 559 581 552 522 461 432 402 430 560 562 550 576 600 624 593 561 495 464 432 440 600 602 589 617 644 669 636 601 530 497 463 450 643 645 631 661 689 716 681 644 568 532 495 460 687 689 674 706 737 765 727 688 607 569 530 470 733 736 720 754 786 817 776 734 648 607 565 480 781 784 767 803 838 871 827 783 691 647 602 490 832 835 817 855 892 927 881 833 735 689 641 500 884 887 868 909 948 985 936 886 781 732 682 510 939 942 922 965 1007 1046 994 940 830 778 724 520 996 999 978 1024 1068 1109 1054 997 880 825 768 530 1055 1058 1035 1084 1131 1175 1117 1056 932 874 813 540 1116 1120 1096 1147 1197 1243 1182 1118 986 924 860 550 1180 1184 1158 1213 1265 1314 1249 1181 1042 977 909 560 1246 1250 1223 1281 1336 1388 1319 1247 1101 1032 960 570 1314 1319 1290 1351 1409 1464 1391 1316 1161 1088 1013 580 1385 1390 1360 1424 1485 1543 1466 1387 1224 1147 1068 590 1458 1463 1432 1499 1564 1625 1544 1460 1289 1208 1124 600 1534 1540 1506 1577 1645 1709 1624 1536 1356 1271 1183 Column spasing 1(cm) Column spasing 1(cm) Column spasing 1(cm) www.balkan.gr

16 Statics Predimensioning, Spar Spacing 100 cm Table for determination of the necessary inertia moments Ix req. [cm 2 ] for spars or mullions of a shed roof or inclined facade of aluminium profiles (E=7000 kn/m 2 ) Load case: Freely supported girder on two supports, trapezoidal or triangular load Bending max f= 1/300* I (values in table apply for max. edge length of individual glazings = 240 cm) Typical snow load So= 0,75 kn/m 2 Dead weight g=0.47 kn/m 2 Vertical individual live load F=1kN Conversion factor for increased snow loads with roof angles up to 60 o (approx. values) For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.2 For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.4 Spar spacing = 100 cm Dynamic pressure q = 0,5 kn/m 2 (building height 0-8m) Dynamic pressure q = 0,8 kn/m 2 (building height 8-20m) Dynamic pressure q = 1,1 kn/m 2 (building height 20-100m) 100 a Roof angle 100 b Roof angle 100 c Roof angle dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o 140 25 21 20 19 17 16 14 12 8 7 6 150 29 25 24 22 20 19 17 14 10 9 8 160 34 29 27 26 24 22 19 17 13 11 10 170 39 33 32 30 27 25 22 20 16 14 12 180 44 38 36 34 31 28 26 24 19 17 14 190 50 44 41 38 35 34 31 28 23 20 17 200 57 52 48 45 41 40 37 33 27 23 20 210 64 60 56 52 48 47 43 39 31 27 24 220 72 70 65 61 56 54 50 45 36 32 27 230 83 81 75 70 64 62 57 52 42 37 31 240 94 92 86 80 73 71 65 60 48 42 36 250 107 105 98 91 83 81 74 68 54 48 41 260 121 118 111 103 94 91 84 77 61 54 46 270 137 133 124 115 106 103 95 86 69 60 52 280 153 149 139 129 119 115 106 96 77 68 58 290 170 166 155 144 132 128 118 108 86 75 65 300 189 185 173 160 147 143 131 119 95 84 72 310 209 204 191 177 163 158 145 132 105 93 80 320 231 225 211 195 179 174 160 146 116 102 88 330 254 248 232 215 197 191 176 160 128 112 97 340 278 272 254 235 216 210 193 176 140 123 106 350 304 297 277 257 236 229 211 192 153 135 116 360 332 324 302 280 257 250 230 209 167 147 126 370 361 352 329 305 280 272 250 228 181 160 137 380 391 382 357 331 304 295 271 247 197 173 149 390 424 413 386 358 329 319 294 267 213 188 161 400 458 446 417 387 355 345 317 289 230 203 174 410 493 481 450 417 383 372 342 311 248 219 188 420 531 518 484 449 412 400 368 335 267 235 202 430 570 557 520 482 443 430 395 360 287 253 217 440 612 597 558 517 475 461 424 386 308 271 233 450 655 639 597 554 508 494 454 413 330 290 249 460 700 683 638 592 544 528 486 442 352 310 266 470 748 729 682 632 580 563 518 472 376 331 284 480 797 778 727 674 619 600 552 503 401 353 303 490 848 828 773 717 659 639 588 535 427 376 323 500 902 880 822 763 700 680 625 569 454 400 343 510 958 934 873 810 743 722 664 604 482 424 364 520 1016 991 926 859 789 765 704 641 511 450 387 530 1076 1050 981 910 835 811 746 679 541 477 409 540 1139 1111 1038 963 884 858 790 718 573 504 433 550 1204 1175 1098 1018 935 907 835 760 606 533 458 560 1271 1240 1159 1075 987 958 881 802 640 563 484 570 1341 1309 1223 1134 1041 1011 930 846 675 594 510 580 1414 1379 1289 1195 1097 1065 980 892 711 626 538 590 1489 1452 1357 1259 1156 1122 1032 939 749 659 566 600 1566 1582 1428 1324 1216 1180 1086 988 788 694 596 140 25 21 20 19 19 20 19 18 16 15 14 150 29 25 24 23 24 25 24 22 20 18 17 160 34 29 27 28 30 31 29 28 24 23 21 170 39 33 33 35 36 38 36 34 30 28 26 180 44 38 40 42 44 46 43 41 36 34 32 190 50 44 48 50 52 54 52 49 43 40 38 200 57 52 56 59 62 64 61 58 51 48 44 210 67 67 66 69 72 75 71 64 59 56 52 220 78 78 77 80 84 87 83 78 69 65 60 230 90 90 88 92 96 100 95 90 79 74 69 240 103 103 101 105 110 114 109 103 91 85 79 250 117 117 114 120 125 130 123 117 103 97 90 260 132 132 129 135 141 147 140 132 116 109 102 270 148 149 146 152 159 165 157 148 131 123 114 280 166 167 163 171 178 185 176 166 147 138 128 290 185 186 182 190 198 206 196 185 164 153 143 300 206 206 202 211 220 229 218 206 182 170 158 310 227 228 223 234 244 253 241 228 201 188 175 320 251 252 246 258 269 279 266 251 222 208 193 330 276 277 271 283 296 307 292 276 244 228 213 340 302 303 297 311 324 337 320 303 267 250 233 350 330 332 324 340 354 368 350 331 292 274 255 360 260 361 354 370 386 401 381 361 318 298 278 370 392 393 385 403 420 436 415 392 346 324 302 380 425 426 417 437 456 473 450 426 376 352 328 390 460 462 452 473 493 513 487 461 407 381 355 400 497 499 488 511 533 554 526 498 439 412 383 410 536 538 526 551 575 597 567 537 474 444 413 420 577 579 566 593 618 643 611 577 510 478 445 430 620 622 608 637 664 690 656 620 547 513 487 440 664 667 652 683 712 740 704 665 587 550 512 450 711 714 698 731 763 793 753 712 629 589 548 460 761 763 747 782 815 847 805 762 672 630 586 470 812 815 797 835 870 905 860 813 717 672 626 480 865 868 850 890 928 964 916 867 765 717 667 490 921 925 905 947 988 1027 976 923 814 763 710 500 980 983 962 1007 1050 1091 1037 981 866 811 755 510 1040 1044 1021 1069 1115 1159 1101 1042 919 862 802 520 1103 1107 1083 1134 1183 1229 1168 1105 975 914 850 530 1169 1173 1147 1201 1253 1302 1238 1170 1033 968 901 540 1237 1241 1214 1271 1326 1378 1310 1239 1093 1024 953 550 1307 1312 1284 1344 1402 1457 1384 1309 1155 1083 1008 560 1381 1386 1356 1419 1480 1538 1462 1383 1220 1144 1064 570 1457 1462 1430 1497 1562 1623 1542 1459 1287 1207 1123 580 1535 1541 1507 1578 1646 1711 1626 1537 1357 1272 1183 590 1617 1622 1587 1662 1733 1801 1712 1619 1429 1339 1246 600 1701 1707 1670 1749 1824 1895 1801 1703 1503 1409 1311 Column spasing 1(cm) 901Column spasing 1(cm) 140 25 21 20 19 17 16 15 14 12 11 10 150 29 25 24 22 20 20 19 18 15 14 13 160 34 29 27 26 25 25 24 22 19 17 16 170 39 33 32 30 30 31 29 27 23 21 19 180 44 38 36 34 36 37 35 32 28 25 23 190 50 44 44 38 43 44 41 39 33 30 27 200 57 55 52 45 51 52 49 45 39 36 32 210 67 64 61 58 60 61 57 53 45 42 38 220 75 74 71 68 69 70 66 62 52 48 44 230 86 85 81 78 80 81 76 71 60 55 50 240 98 98 93 89 91 93 87 81 69 63 58 250 112 111 105 101 104 105 99 92 79 72 65 260 127 125 119 115 117 119 112 104 89 81 74 270 142 141 134 129 132 134 126 117 100 92 83 280 159 158 150 144 147 150 141 131 112 103 93 290 178 176 167 161 164 167 157 146 125 114 104 300 197 185 189 179 183 186 174 163 138 127 115 310 218 216 206 198 202 206 193 180 153 141 128 320 241 239 227 218 223 227 213 198 169 155 141 330 265 262 249 240 245 249 234 218 186 170 155 340 290 287 273 263 268 273 256 239 204 187 169 350 317 314 299 288 293 299 280 261 222 204 185 360 346 342 326 313 320 326 306 285 243 223 202 370 376 372 354 341 348 354 332 310 264 242 220 380 408 404 384 370 377 384 361 336 286 263 238 390 442 437 416 400 408 416 390 364 310 284 258 400 477 473 450 433 441 449 422 393 335 307 279 410 514 510 485 466 476 484 455 424 361 331 300 420 554 548 522 502 512 521 489 456 388 356 323 430 595 589 560 539 550 560 526 490 417 383 347 440 638 632 601 578 590 601 564 526 447 411 372 450 683 676 644 619 632 643 604 563 479 440 399 460 730 723 688 662 675 688 645 602 512 470 426 470 779 772 734 707 721 734 689 642 547 502 455 480 831 823 783 753 768 782 734 685 583 535 485 490 885 876 834 802 818 833 782 729 620 569 517 500 940 931 886 853 870 885 831 775 660 605 549 510 999 989 941 905 924 940 883 823 700 643 583 520 1059 1049 998 960 979 997 936 873 743 682 618 530 1122 1111 1057 1017 1038 1057 992 925 787 722 655 540 1187 1176 1119 1076 1098 1118 1050 978 833 764 693 550 1255 1243 1183 1138 1161 1182 1110 1034 880 808 733 560 1326 1313 1249 1202 1226 1248 1172 1092 930 853 774 570 1398 1385 1318 1268 1293 1317 1236 1152 981 900 817 580 1474 1460 1389 1336 1363 1388 1303 1215 1034 949 861 590 1552 1537 1463 1407 1435 1462 1372 1279 1089 999 906 600 1633 1618 1539 1480 1510 1538 1444 1346 1146 1051 954 Column spasing 1(cm) April 2009

Statics Predimensioning, Spar Spacing 110 cm 17 Table for determination of the necessary inertia moments Ix req. [cm 2 ] for spars or mullions of a shed roof or inclined facade of aluminium profiles (E=7000 kn/m 2 ) Load case: Freely supported girder on two supports, trapezoidal or triangular load Bending max f= 1/300* I (values in table apply for max. edge length of individual glazings = 240 cm) Typical snow load So= 0,75 kn/m 2 Dead weight g=0.47 kn/m 2 Vertical individual live load F=1kN Conversion factor for increased snow loads with roof angles up to 60 o (approx. values) For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.2 For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.4 Spar spacing = 110 cm Dynamic pressure q = 0,5 kn/m 2 (building height 0-8m) Dynamic pressure q = 0,8 kn/m 2 (building height 8-20m) Dynamic pressure q = 1,1 kn/m 2 (building height 20-100m) 110 a Roof angle 110 b Roof angle 110 c Roof angle dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o 140 25 21 20 19 17 16 14 12 9 8 6 150 29 25 24 22 20 19 17 14 11 10 8 160 34 29 27 26 24 22 19 17 14 12 10 170 39 33 32 30 27 25 23 21 17 15 13 180 44 38 37 34 31 30 28 25 20 18 15 190 50 44 44 41 37 36 33 30 24 21 18 200 57 56 52 48 44 43 39 36 29 25 22 210 67 65 61 56 52 50 46 42 34 30 25 220 78 76 71 66 60 58 54 49 39 34 29 230 89 87 81 76 69 67 62 56 45 40 34 240 102 100 93 87 79 77 71 65 51 45 39 250 116 114 106 98 90 88 81 73 59 52 44 260 132 129 120 111 102 99 91 83 66 58 50 270 148 145 135 125 115 112 103 94 75 66 56 280 166 162 152 141 129 125 115 105 84 74 63 290 186 181 169 157 144 140 129 117 93 82 71 300 206 201 188 174 160 155 143 130 104 91 78 310 228 223 208 193 177 172 158 144 115 101 87 320 252 246 230 213 196 190 175 159 127 112 96 330 277 270 253 234 215 209 192 175 139 123 105 340 304 296 277 257 236 229 211 192 153 135 116 350 332 324 303 281 258 250 230 210 167 147 126 360 362 354 330 306 281 273 251 229 182 161 138 370 394 385 359 333 306 297 273 249 198 175 150 380 428 417 390 362 332 322 297 270 215 190 163 390 463 452 422 392 360 349 321 292 233 205 176 400 501 489 457 423 389 377 347 316 252 222 191 410 540 527 492 457 419 407 374 341 272 239 205 420 581 567 530 491 451 438 403 367 292 257 221 430 625 609 569 528 485 471 433 394 314 277 238 440 670 654 611 567 520 505 465 423 337 297 255 450 718 700 654 607 557 541 497 453 361 318 273 460 767 749 700 649 596 578 532 484 386 340 292 470 819 799 747 693 636 617 568 517 412 363 312 480 873 852 796 738 678 658 606 551 439 387 332 490 930 907 848 786 722 701 645 587 468 412 354 500 989 965 902 836 768 745 686 624 497 438 376 510 1050 1025 957 888 815 791 728 663 528 465 400 520 1114 1087 1016 942 865 839 772 703 560 493 424 530 1180 1151 1076 998 916 889 818 745 594 523 449 540 1249 1219 1139 1056 970 941 866 788 628 553 475 550 1321 1288 1204 1117 1025 995 916 833 664 585 503 560 1395 1361 1272 1179 1083 1051 967 880 702 618 531 570 1472 1436 1342 1244 1142 1109 1020 928 740 652 560 580 1551 1513 1414 1312 1204 1169 1075 979 780 687 590 590 1634 1594 1489 1381 1268 1231 1133 1031 822 724 622 600 1719 1677 1567 1453 1334 1295 1192 1084 865 761 654 140 25 21 20 19 20 21 20 18 16 15 14 150 29 25 24 24 25 26 25 24 21 20 18 160 34 30 29 30 32 33 31 29 26 24 23 170 39 36 35 37 39 40 38 36 32 30 28 180 44 44 43 45 47 49 46 44 39 36 34 190 52 52 51 54 56 58 55 52 46 43 40 200 62 62 61 64 66 69 65 62 55 51 48 210 72 73 71 74 78 81 77 73 64 60 56 220 84 84 83 87 90 94 89 84 74 70 65 230 97 97 95 100 104 108 103 97 86 80 75 240 111 112 109 114 119 124 118 111 98 92 86 250 126 127 124 130 136 141 134 127 112 105 97 260 143 144 141 147 153 159 152 143 126 119 110 270 161 162 158 166 173 180 171 161 142 133 124 280 181 181 177 186 194 201 191 181 160 150 139 290 202 202 198 207 216 225 213 202 178 167 155 300 224 225 220 230 240 250 237 224 198 186 173 310 248 249 243 255 266 276 263 248 219 205 191 320 274 275 269 281 293 305 290 274 242 227 211 330 301 302 295 309 323 335 319 301 266 249 232 340 330 331 324 339 354 368 349 330 292 273 254 350 361 362 354 371 387 402 382 361 319 299 278 360 394 395 386 405 422 439 417 394 348 326 303 370 428 430 420 440 459 477 453 429 378 355 330 380 465 466 456 478 498 518 492 465 411 385 358 390 503 505 494 517 540 561 533 504 445 417 388 400 544 546 534 559 583 606 576 545 481 450 419 410 586 589 576 603 629 653 621 587 518 486 452 420 631 634 620 649 677 703 668 632 558 523 487 430 678 681 666 697 727 756 718 679 599 562 523 440 728 730 714 748 780 811 770 729 643 603 561 450 779 782 765 801 835 868 825 780 689 645 601 460 833 836 818 857 893 928 882 834 736 690 642 470 890 893 873 915 954 991 942 891 786 737 686 480 948 952 931 975 1017 1057 1004 950 838 786 731 490 1010 1013 991 1038 1083 1125 1069 1011 892 836 778 500 1074 1078 1054 1104 1151 1197 1137 1075 949 889 828 510 1140 1144 1120 1172 1223 1271 1208 1142 1008 945 879 520 1210 1214 1188 1244 1297 1348 1281 1211 1069 1002 932 530 1282 1286 1258 1318 1374 1438 1357 1284 1133 1062 988 540 1357 1361 1332 1395 1454 1511 1436 1358 1199 1124 1046 550 1434 1439 1408 1474 1538 1598 1519 1436 1267 1188 1106 560 1515 1520 1487 1557 1624 1688 1604 1517 1338 1255 1168 570 1598 1604 1569 1643 1713 1781 1692 1600 1412 1324 1232 580 1685 1690 1654 1732 1806 1877 1784 1687 1489 1395 1299 590 1774 1780 1742 1824 1902 1977 1879 1777 1568 1469 1368 600 1867 1873 1833 1919 2001 2080 1977 1869 1650 1546 1439 Column spasing 1(cm) 901Column spasing 1(cm) 140 25 21 20 19 17 17 16 15 12 11 10 150 29 25 24 22 21 21 20 19 16 15 13 160 34 29 27 26 26 27 25 23 20 18 16 170 39 34 33 31 32 33 31 29 24 22 20 180 44 42 40 38 39 40 37 35 29 27 25 190 50 50 47 46 46 47 44 41 35 32 29 200 59 59 56 54 55 56 52 49 42 38 35 210 70 69 66 63 64 66 61 57 49 45 41 220 81 80 76 73 75 76 71 67 57 52 47 230 93 92 88 84 86 88 82 77 65 60 54 240 107 106 101 97 99 100 94 88 75 69 62 250 121 120 114 110 112 114 107 100 85 78 71 260 137 136 129 125 127 129 121 113 96 88 80 270 155 153 146 140 143 146 137 128 109 100 90 280 173 172 163 157 160 163 153 143 122 112 101 290 193 192 182 175 179 182 171 159 136 125 113 300 215 213 203 195 199 202 190 177 151 138 126 310 238 236 224 216 220 224 210 196 167 153 139 320 263 260 248 238 243 247 232 216 184 169 153 330 289 286 272 262 267 272 255 238 203 186 169 340 317 314 299 287 293 298 280 261 222 204 185 350 346 343 326 314 320 326 306 286 243 223 202 360 378 374 356 343 349 356 334 311 265 243 221 370 411 407 387 373 380 387 363 339 288 265 240 380 446 442 420 404 413 420 394 368 313 287 261 390 483 479 455 438 447 455 427 398 339 311 282 400 522 517 492 473 483 492 461 430 366 336 305 410 563 558 531 510 521 530 498 464 395 362 329 420 606 600 571 549 561 571 536 499 425 390 354 430 651 645 614 590 602 613 576 537 457 419 380 440 699 692 658 633 646 658 617 576 490 450 408 450 748 741 705 678 692 704 661 617 525 482 437 460 800 792 754 725 740 753 707 659 561 515 467 470 854 846 805 774 790 804 755 704 599 550 499 480 911 902 858 826 842 857 805 750 639 586 532 490 970 960 914 879 897 913 857 799 680 624 566 500 1031 1021 971 935 953 971 911 850 723 664 602 510 1095 1084 1032 993 1013 1031 968 902 768 705 639 520 1161 1150 1094 1053 1074 1094 1027 957 815 748 678 530 1231 1219 1160 1116 1138 1159 1088 1014 863 792 719 540 1302 1290 1227 1181 1204 1226 1151 1073 914 838 760 550 1377 1364 1297 1248 1273 1296 1217 1135 966 886 804 560 1454 1440 1370 1318 1345 1369 1285 1198 1020 936 849 570 1534 1520 1446 1391 1419 1445 1356 1264 1076 988 896 580 1617 1602 1524 1466 1496 1523 1430 1333 1134 1041 944 590 1703 1687 1605 1544 1575 1604 1506 1404 1195 1097 995 600 1792 1775 1689 1625 1657 1687 1584 1477 1257 1154 1047 Column spasing 1(cm) www.balkan.gr

18 Statics Predimensioning, Spar Spacing 120 cm Table for determination of the necessary inertia moments Ix req. [cm 2 ] for spars or mullions of a shed roof or inclined facade of aluminium profiles (E=7000 kn/m 2 ) Load case: Freely supported girder on two supports, trapezoidal or triangular load Bending max f= 1/300* I (values in table apply for max. edge length of individual glazings = 240 cm) Typical snow load So= 0,75 kn/m 2 Dead weight g=0.47 kn/m 2 Vertical individual live load F=1kN Conversion factor for increased snow loads with roof angles up to 60 o (approx. values) For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.2 For typical snow load So=1,00 kn/m 2, the values in the table must be multiplied by 1.4 Spar spacing = 120 cm Dynamic pressure q = 0,5 kn/m 2 (building height 0-8m) Dynamic pressure q = 0,8 kn/m 2 (building height 8-20m) Dynamic pressure q = 1,1 kn/m 2 (building height 20-100m) 120 a Roof angle 120 b Roof angle 120 c Roof angle dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o dis25 o 30 o 35 o 40 o 45 o 50 o 55 o 60 o 70 o 80 o 90 o 140 25 21 20 19 17 16 14 12 9 8 7 150 29 25 24 22 20 19 17 14 11 10 9 160 34 29 27 26 24 22 20 18 14 13 11 170 39 33 32 30 27 26 24 22 18 16 13 180 44 42 39 36 33 32 30 32 21 23 19 190 51 50 47 43 40 39 35 32 26 23 19 200 61 59 55 51 47 46 42 38 30 27 23 210 71 69 65 60 55 54 49 45 36 32 27 220 83 81 76 70 64 62 57 52 42 37 32 230 96 93 87 81 74 72 66 60 48 42 36 240 110 107 100 93 85 83 76 69 55 49 42 250 125 122 114 106 97 94 87 79 63 55 48 260 142 138 129 120 110 107 98 89 71 63 54 270 160 156 146 135 124 120 111 101 80 71 61 280 179 175 163 152 139 135 124 113 90 79 68 290 200 195 182 169 155 151 139 126 101 89 76 300 223 217 203 188 173 168 154 140 112 99 85 310 247 241 225 209 191 186 171 156 124 109 94 320 272 266 248 230 211 205 189 172 137 121 104 330 300 292 273 253 233 226 208 189 151 133 114 340 329 321 300 378 255 248 228 207 165 146 125 350 360 351 328 304 279 271 249 227 181 159 137 360 392 383 358 332 305 296 272 248 197 174 149 370 427 417 389 361 332 322 296 269 215 189 163 380 464 452 423 392 360 349 322 293 233 205 176 390 502 490 458 425 390 379 348 317 253 223 191 400 543 530 495 459 422 409 376 343 273 241 207 410 586 572 534 495 455 441 406 370 295 259 223 420 631 615 575 533 490 475 437 398 317 279 240 430 678 661 648 573 526 511 470 428 341 300 258 440 727 710 663 615 565 548 504 459 366 322 277 450 779 760 710 659 605 587 540 492 392 345 277 460 833 813 760 705 647 628 578 526 419 369 317 470 890 868 811 752 691 670 617 561 448 394 339 480 949 926 865 802 737 715 658 599 477 420 361 490 1011 986 921 854 784 761 701 638 508 448 385 500 1075 1049 980 909 834 810 745 678 541 476 409 510 1142 1114 1041 965 886 860 791 720 574 506 434 520 1211 1182 1104 1024 940 912 840 764 609 536 461 530 1283 1252 1170 1085 996 967 890 810 646 568 488 540 1358 1325 1238 1148 1054 1023 942 857 683 602 517 550 1436 1401 1309 1214 1115 1082 996 906 722 636 547 560 1517 1480 1383 1283 1178 1143 1052 957 763 672 577 570 1601 1562 1459 1353 1243 1206 1110 1010 805 709 609 580 1688 1646 1539 1427 1310 1271 1170 1065 849 747 642 590 1777 1734 1620 1503 1380 1339 1232 1121 894 787 676 600 1870 1825 1705 1581 1452 1409 1297 1180 941 828 712 140 25 21 20 20 20 21 20 19 17 16 15 150 29 25 24 25 26 27 26 31 27 26 24 160 34 31 30 32 33 34 33 31 27 26 24 170 39 38 37 39 41 42 40 38 34 32 29 180 46 46 45 48 50 52 49 46 41 38 36 190 56 56 54 57 60 62 59 56 49 46 43 200 66 66 65 68 71 73 70 66 58 55 51 210 77 78 76 79 83 86 82 77 68 64 60 220 90 90 88 93 96 100 95 90 80 75 69 230 104 104 102 107 111 116 110 104 92 86 80 240 119 120 117 123 128 133 126 119 105 99 92 250 136 136 133 140 146 151 144 136 120 113 105 260 154 154 151 158 165 172 163 154 136 128 119 270 174 174 170 178 186 193 184 174 153 144 134 280 195 195 191 200 209 217 206 195 172 161 150 290 217 218 213 223 233 242 230 218 192 180 168 300 242 243 237 249 259 269 256 242 214 200 186 310 268 269 263 275 287 298 284 268 237 222 206 320 296 297 290 304 317 330 313 296 261 245 228 330 325 327 320 335 349 363 345 326 288 270 251 340 357 358 351 367 383 398 378 358 316 296 275 350 391 392 384 402 419 435 414 391 345 324 301 360 426 428 418 438 457 475 451 427 377 353 329 370 464 466 455 477 497 517 491 465 410 384 358 380 504 505 494 518 540 561 533 504 445 417 388 390 546 547 536 561 585 608 578 546 482 252 421 400 590 592 579 606 632 657 624 591 521 488 455 410 636 638 625 654 682 709 674 637 562 527 490 420 685 687 673 704 737 763 725 686 605 567 528 430 736 739 723 757 789 820 780 737 651 610 568 440 790 793 776 812 847 880 836 791 698 654 609 450 846 849 831 870 907 943 896 847 748 701 652 460 905 908 888 930 970 1008 958 906 800 750 698 470 966 970 949 994 1036 1077 1023 968 854 800 745 480 1031 1034 1012 1059 1105 1148 1091 1032 911 854 794 490 1097 1101 1077 1128 1177 1223 1162 1099 970 909 846 500 1167 1171 1146 1200 1251 1300 1236 1169 1031 967 900 510 1240 1244 1217 1274 1329 1381 1313 1241 1095 1027 956 520 1315 1320 1291 1352 1410 1465 1393 1317 1162 1089 1014 530 1394 1398 1368 1433 1494 1553 1476 1396 1232 1154 1074 540 1475 1480 1448 1516 1582 1644 1562 1477 1304 1222 1137 550 1560 1565 1531 1603 1672 1738 1652 1562 1378 1292 1202 560 1647 1653 1617 1694 1766 1836 1744 1650 1456 1365 1270 570 1738 1745 1707 1787 1864 1937 1841 1741 1536 1440 1340 580 1833 1839 1799 1884 1965 2042 1941 1835 1619 1518 1413 590 1930 1937 1895 1984 2070 2151 2044 1933 1706 1599 1488 600 2031 2038 1994 2088 2178 2263 2151 2034 1795 1682 1566 Column spasing 1(cm) Column spasing 1(cm) 901Column spasing 1(cm) 140 25 21 20 19 17 17 16 15 13 12 11 150 29 25 24 22 22 22 21 19 17 15 14 160 34 29 28 27 27 28 26 24 21 19 17 170 39 36 34 33 34 34 32 30 26 24 21 180 44 44 42 40 41 42 39 37 31 29 26 190 53 53 50 48 49 50 47 44 37 34 31 200 63 63 60 57 58 60 56 52 44 41 37 210 74 74 70 67 69 70 66 61 52 48 43 220 86 86 81 78 80 81 76 71 61 56 50 230 100 99 94 90 92 94 88 82 70 64 58 240 114 113 108 104 106 108 101 94 80 74 67 250 130 129 123 118 121 123 115 107 91 84 76 260 148 146 139 134 137 139 131 122 104 95 86 270 167 165 157 151 154 157 147 137 117 107 97 280 187 185 176 169 173 176 165 154 131 120 109 290 209 207 197 189 193 196 184 172 146 134 122 300 232 230 219 210 215 219 205 191 163 149 136 310 257 255 242 233 238 242 227 212 180 166 150 320 284 281 268 257 263 267 251 234 199 183 166 330 312 310 294 283 289 294 276 258 219 201 182 340 343 340 323 311 317 323 303 283 240 221 200 350 375 372 353 340 347 353 332 309 263 241 219 360 409 405 386 371 378 385 362 337 287 263 239 370 445 441 420 404 412 419 394 367 312 287 260 380 484 479 456 438 447 455 427 398 339 311 282 390 524 519 494 475 484 493 463 432 367 337 306 400 566 561 534 513 524 533 500 467 397 365 331 410 611 605 576 554 565 575 540 503 428 393 357 420 658 651 620 596 608 619 581 542 461 423 384 430 707 700 666 641 654 666 625 583 496 455 413 440 758 751 715 688 701 714 670 625 532 488 443 450 812 805 766 736 751 765 718 669 570 523 474 460 869 861 819 788 804 818 768 716 609 559 507 470 928 919 874 841 858 874 820 765 651 597 542 480 989 980 932 897 915 922 875 815 694 637 578 490 1054 1044 993 897 915 922 875 868 739 678 615 500 1120 1110 1056 1016 1036 1055 990 923 786 721 654 510 1190 1179 1122 1079 1101 1121 1052 981 835 766 695 520 1263 1251 1190 1145 1168 1189 1116 1041 886 813 737 530 1338 1325 1261 1213 1237 1260 1183 1103 939 861 781 540 1416 1403 1335 1284 1310 1333 1252 1167 993 912 827 550 1497 1483 1411 1358 1385 1410 1324 1234 1050 964 874 560 1582 1567 1490 1434 1463 1489 1398 1303 1109 1018 924 570 1669 1653 1573 1513 1544 1572 1475 1375 1171 1074 924 580 1759 1743 1658 1595 1627 1657 1555 1450 1234 1133 1027 590 1853 1836 1746 1680 1714 1745 1638 1527 1300 1193 1082 600 1950 1932 1838 1768 1803 1836 1724 1607 1368 1255 1139 April 2009

Calculation of the heat transmission coefficient Ucw 19 U cw value (CURTAIN WALLING) to pren 13947 pren 13947 defines a method for determining the heat transmission coefficient Ucw of a curtain facade system consisting of glass fillings and / or non-transparent fillings in frames or sashes. Window Frame Window The heat transmission coefficient U cw of a curtain facade system is calculated using the following equation: U cw = Σ Α g U g + ΣA p U p + ΣΑ f U f + ΣΙ g Ψ g + ΣΙ p Ψ p ΣΑ g + A f + A p A CW Area ratio of the facade module A f, A t, A m Area ratio of the profiles A g Area ratio of the glazing A p Area ratio of the filling U f, U m, U t U g U p Ψ g, Ψ p Ι g Thermal transmission coefficient of the profiles (windows, mullions, transoms) Thermal transmission coefficient of the glazing Thermal transmission coefficient of the filling Length-related heat transmission coefficient of the glazing or panel spacer Length of the visible glazing perimeter Ι p Length of the visible filling perimeter Note: The visible surfaces Ag and/or Ap are the smaller of the surfaces visible from the two sides. The total of the length lg and/or Ip is the total of the visible glazing or filling perimeter. If different lengths are visible from the two viewing sides, the larger of the two has to be used. www.balkan.gr

20 Nominal values of the heat transmission coefficient U f Nominal values of the heat transmission coefficient U f Fixed cross-section Mounting mullion Mullion Moving cross-sections Mullion with integrated sash, glazing bonded The illustrated Uf values of the mullion-and-transom construction W 50 Were measured according to EN 12412-2 : 2009-07 and calculated according to EN 10077-2 : 2003-10 The allowance for the influence of the facade screws has already been taken into account. Screw Ø 5,5 mm Spacing approx 250 mm Insert cross-sections April 2009

Mullion profiles, vertical (Level 3) Profiles 21 10 10 10 10 10 50 50 10 7.1 2.5 80 87 37 11.5 83.5 100 107 11.5 7 7 10 7.1 2.5 63.5 14 20 30 26 AE013-000001-00 AE013-000002-00 AE013-929001-00 AE013-000003-00 ( PK 393 ) ( PK 392) ( PK 390 ) ( PK 391 ) AE013-000004-00 Reinforcement AH550-5182080 Reinforcement AH550-5182100 46.4 46.4 AH550-5114084 4,00 m delivery length AH550-5114080 6,00 m delivery length Mullion profile Dev. anod.: 416 mm Weight: 1,85 kg/m Dev. mech.: 210 mm Ix cm 4 : 62,76 AH550-5114104 4,00 m delivery length AH550-5114100 6,00 m delivery length Mullion profile Dev. anod.: 456 mm Weight: 2,05 kg/m Dev. mech.: 250 mm Ix cm 4 : 107,53 www.balkan.gr

22 Mullion profiles, vertical (Level 3) Profiles 900 94036 Matrizen und Stempel fr Stanzvorrichtung 900 94070 Mullion Level 3 900 94050 Einzelwerkzeug fr Stanzmaschinen 50,4 50 11,5 10 7.1 2.5 50 7 140 147 10 7.1 2.5 11.5 120 127 123.5 103.5 11.5 7 Reinforcement AH550-5182120 Reinforcement AH550-5182140 46.4 46.4 ΑΗ550-5114124 4,00 m delivery length ΑΗ550-5114120 6,00 m delivery length Mullion profile Dev. anod.: 496 mm Weight: 2,22 kg/m Dev. mech.: 290 mm Ix cm 4 : 167,14 ΑΗ550-5114140 Mullion profile Dev. anod.: 536 mm Weight: 2,45 kg/m Dev. mech.: 330 mm Ix cm 4 : 243,04 April 2009

Mullion profiles, vertical (Level 3) Profiles 23 50 10 7.1 2.5 50 7 10 7.1 2.5 143.4 160 167 11.5 180 187 11.5 7 Reinforcement AH550-5182160 162 45.8 45 ΑΗ550-5114160 Mullion profile Dev. anod.: 576 mm Weight: 2,85 kg/m Dev. mech.: 370 mm Ix cm 4 : 352,81 ΑΗ550-5114180 Mullion profile Dev. anod.: 616 mm (not permanently in stock) Weight: 3,60 kg/m Dev. mech.: 410 mm Ix cm 4 : 553,02 www.balkan.gr

24 Mullion profiles, vertical (Level 3) Profiles 25 50 30 10 7.1 2.5 ΑΕ013-929036-20 11.5 180.8 200 207 7 ΑH550-5150015 ΑΗ550-5150053 W51 50053 Illustration shows clamped glazing ΑΗ550-5115080 Mullion profile, vertical for sash installation Dev. anod.: 384 mm Weight: 1,53 kg/m Dev. mech.: 95 mm Ix cm 4 : 39,89 44.6 ΑΗ550-5114200 (not permanently in stock) Mullion profile Dev. anod.: 656 mm Weight: 4,23 kg/m Dev. mech.: 450 mm Ix cm 4 : 790,30 April 2009

Mullion profiles, vertical (Level 3) Profiles 25 25 25 PK 426 ΑΕ013-929036-20 PK 426 ΑΕ013-929036-20 7.1 2.5 95 33 33 33 7.1 2.5 11.5 120 7 160 160 7 55 33 11.5 ΑΗ550-5150053 W51 50053 200 ΑΗ550-5150053 W51 50053 4.5 66.5 66.5 4.5 15 Dies and punches for punching device 50,4 Illustration shows clamped glazing 11,5 Level 3 15 ΑΗ550-5115120 Mullion profile, vertical for sash installation Dev. anod.: 464 mm Weight: 1,93 kg/m Dev. mech.: 135 mm Ix cm 4 : 111,40 ΑΗ550-5115160 Mullion profile, vertical for sash installation Dev. anod.: 544 mm Weight: 2,32 kg/m Dev. mech.: 270 mm Ix cm 4 : 249,00 www.balkan.gr

26 Mullion corner profiles 90, vertical (Level 3) Profiles AH550-5113080 Mullion corner profiles 90 o Dev. anod.: 632 mm Weight: 2,85 kg/m Dev. mech.: 160 mm Ix cm 4 : 83,60 St tube 60/60 AE013-929001-01 April 2009

profiles, vertical (Level 1) Profiles 27 The figures apply to a self-powered double punching machine No. 900 94070 Dies and punches for 900 94070 cutting out of the mullion profiles Mullion Level 3 Dies and punches for 900 94070 cutting out of the mullion profiles = 94037 Dies and punches for 900 94070 cutting out of the mullion profiles = 94038 Level 1 900 94050 Punching tool for cutting out mullion, mounting mullion and transom profiles for use on HSP 110, Dyno 6, etc. Level 2 900 94036 50 10 7.1 2.5 AH550-5184046 T 902 00216 65.9 77 84 6.1 7 16 8,3 50,4 46.4 AH550-5121077 + (not permanently in stock) profile for vertical application Dev. anod.: 354 mm Weight: 1,645 kg/m Dev. mech.: 254 mm Ix cm 4 : 55,84 www.balkan.gr

28 profiles, horizontal (Level 2) Profiles 50 10 7.1 50 2.5 10 7.1 7 2.5 7 8.9 30.5 10.9 17.9 8.9 46.4 AH550-5184046 10.6 23.5 ΑΗ550-5122011 + (not permanently in stock) profile for horizontal installation Dev. anod.: 252 mm Weight: 0,69 kg/m Dev. mech.: 72 mm Ix cm 4 : 0,61 ΑΗ550-5122024 profile for horizontal installation Dev. anod.: 276 mm Weight: 1,06 kg/m Dev. mech.: 97 mm Ix cm 4 : 2,85 50 10 7.1 50 2.5 10 7.1 7 2.5 8.9 7 38.5 25.6 45.5 8.9 60.5 AH550-5184046 T 902 00203 AH550-5184046 T 902 00202 40.6 53.5 46.4 46.4 ΑΗ550-5122039 profile for horizontal installation Dev. anod.: 306 mm Weight: 1,20 kg/m Dev. mech.: 127 mm Ix cm 4 : 9,09 ΑΗ550-5122054 profile for horizontal installation Dev. anod.: 336 mm Weight: 1,36 kg/m Dev. mech.: 157 mm Ix cm 4 : 20,07 April 2009

Profiles profiles, horizontal (Level 2) 29 30 W51 50059 ΑH550-5150053 AH550-5122080 profile, horizontal for sash installation Dev. anod.: 386 mm Weight: 1,50 kg/m Dev. mech.: 95 mm Ix cm 4 : 41,10 15 PK 413 4.5 ΑΕ013-929036-20 7.1 2.5 T-connector 902 00185 with T-connector drilling template ΑH550-5184999 902 00185 907 00027 with drilling template 907 00027 15 33 7 80 120 50 10 7.1 2.5 50 10 7.1 2.5 84.6 8.9 AH550-5184046 T 902 00205 65.6 78.5 85.5 98.5 105.5 8.9 AH550-5184046 T 902 00204 46.4 46.4 AH550-5122079 profile for horizontal installation Dev. anod.: 385 mm Weight: 1,59 kg/m Dev. mech.: 207 mm Ix cm 4 : 50,74 AH550-5122099 profile for horizontal installation Dev. anod.: 426 mm Weight: 1,92 kg/m Dev. mech.: 247 mm Ix cm 4 : 101,07 www.balkan.gr

30 profiles, horizontal (Level 2) Profiles Max. glazing weight 150 kg per glazing support 75 kg 33 50 10 7.1 2.5 50 7 10 7.1 2.5 8.9 3 17 Glazing support AE011-903000-35 from profile AH550-5156042 Cut length 125 mm 8.9 7 T 902 00207 T 902 00206 AH550-5184046 104.6 118.5 125.5 AH550-5184046 124.6 138.5 145.5 46.4 46.4 AH550-5122119 profile for horizontal installation Dev. anod.: 466 mm Weight: 2,12 kg/m Dev. mech.:287 mm Ix cm 4 : 157,44 AH550-5122139 profile for horizontal installation Dev. anod.: 506 mm Weight: 2,30 kg/m Dev. mech.: 327 mm Ix cm 4 : 229,37 April 2009

profiles, horizontal (Level 2) Profiles 31 50 10 7.1 2.5 144.6 158.5 165.5 8.9 7 AH550-5184046 T 902 00208 45.8 AH550-5122159 profile for horizontal installation Dev. anod.: 546 mm Weight: 2,74 kg/m Dev. mech.: 367 mm Ix cm 4 : 334,15 www.balkan.gr

Profiles 32 Profiles Adapter frame profile W51 50015 (C 35 anodised) and sash profile are screwed together after the paint treatment and assembled to form a common sash on which the glazing is then bonded by an authorised gas company. 23.7 AH550-5150015 Adapter frame profile for window sash Dev. anod.: 139 mm Weight: 0,31 kg/m (always C 35 anodised) 11.6 30 15 53 904 AF004-904000-75 00075 15 UV-resistant edge bonding always required 27 14.5 Glazing support 42 5 W51 50015 Corner connector AH900-TF558 AΕ001-901003-45 Drilling template 907 00023 PK 413 W51 22080 19.5 AH550-5150053 Sash profile for bonded glazing (flush surface with fixed glazing) Dev. anod.: 241 mm Weight: 0,99 kg/m Dev. mech.: 95 mm Ix cm 4 : 13,72 AF004-904000-75 Glazing support Corner connector AH900-TF558 AE001-901003-45 Drilling template 907 00023 AE013-929036-20 AH550-5122080 April 2009

Profiles 33 Profiles 50 35 15 AH550-5150080 7 80 Mullion W51 15080 AH550-5115080 Glazing bar, vertical above and below sash glazings Dev. anod.: 255 mm Weight: 1,060 kg/m Dev. mech.: 115 mm Ix cm 4 : 22,26 2.5 7.1 7.1 6 Sash profile for bonded glazing AH550-5150001 2 Glazing support profile for window sash (glued glazing) Dev. anod.: 54 mm Weight: 0,178 kg/m Dev. mech.: 0 mm Cut to length, 125 mm long = AE011-903000-31 30 15 27 W51 50015 Sash profile for bonded glazing AH550-5156053 Glazing support profile for window sash (clamped glazing) Dev. anod.: 124 mm Weight: 0,390 kg/m Dev. mech.: 0 mm Cut to length, 125 mm long = AE011-903000-33 26 7 16 Cut to length, 125 mm long = AE011-903000-35 AH550-5156042 Glazing support profile for fixed glazing horizontal half transom Dev. anod.: 94 mm Weight: 0,350 kg/m Dev. mech.: 0 mm www.balkan.gr

Profiles 34 Profiles 50 6 AH550-5051006 Pressure profile Dev. anod.: 155 mm Dev. mech: 50 mm Weight: 0,538 kg/m 50 12 AH550-5061012 Cover profile Dev. anod.: 147 mm Dev. mech: 74 mm Weight: 0,240 kg/m 49.3 10.5 AH550-5057010 Pressure profile Dev. anod.: 182 mm Dev. mech: 0 mm Weight: 0,410 kg/m 50 15 AH550-5061015 Cover profile Dev. anod.: 159 mm Dev. mech: 80 mm Weight: 0,280 kg/m April 2009

Profiles, pressure and cover profiles Profiles 35 50 97,7 AH550-5063098 acces. AE005-000001-00 Cover profile Dev. anod.: 293 mm Weight: 1,340 kg/m Dev. mech: 206 mm 50 50 20 30 AH550-5061020 Cover profile Dev. anod.: 177 mm Dev. mech: 90 mm Weight: 0,301 kg/m AH550-5067030 Pressure profile + not permanently in stock Dev. anod.: 248 mm Weight: 0,880 kg/m Dev. mech: 155 mm www.balkan.gr

36 Frame inserts, Series RG block windows for facade Profiles AH900- TF495 AH275-5075027 AH275-5075027 Frame Frame inserts inserts for for Series RG 75 Dev. Series anod.: 474 RG / 75 Weight: 1,734 k 354* mm Dev. anod.: 474 / 354* mm Dev. mech.: 104mm Dev. mech.: 104mm Weight: 1,734 kg/m AH900-TF483 Drilling template 907 00347 Processing, see Series RGΒ block windows Installation situation in facade April 2009

Frame inserts, Series RG 75 facade Profiles 37 73.5 19.5 30 AE001- E/P 901 569 901569-00 4 24 10 AH275-5075030 Frame inserts for Series RG 75 Dev. anod.: 474 / 339* mm Weight: 1,871 kg/m Dev. mech.: 85mm 28 38.5 AE001- E 901 458 P 901459-00 4.5 70.5 75 8.5 16.5 72.5 56 Drilling template 907 229 Processing, see Series RG 75 904 495 904 115 RG 1210 AH550-5075030 904 285 50 105.5 www.balkan.gr

38 Frame inserts, Series facade Accessories 15 43.1 22.4 75 AH550-5150003 Frame inserts for flap window Dev. anod.: 407 mm Weight: 1,488 kg/m Dev. mech.: 43 mm 11.3 44.8 Installation situation in facade 50 60.4 April 2009

Window inserts, Series facade Profiles 39 11.5 11.8 26 57 6 25 64 AH275-280 Sash inserts for flap window Dev. anod.: 384 mm Weight: 1,681 kg/m Dev. mech.: 92 mm Ix cm 4 : 10,51 28.7 19.5 Installation situation in facade 50 60.4 www.balkan.gr

40 Auxiliary and connecting profiles Profiles 7.1 12.1 7.1 12.1 3.5 8.5 8 AH550-9071008 Spacer profile 8mm Dev. anod.: 69 mm Dev. mech.: 16 mm Weight: 0,120 kg/m AH550-9071010 Spacer profile 10mm Dev. anod.: 77 mm Dev. mech.: 20 mm Weight: 0,150 kg/m AH550-5150001 Glass support for flap window (standard cw) Dev. anod.: 54 mm Dev. mech.: 0 mm Weight: 0,178 kg/m 20 24.7 16 19.8 7.7 10 20 20 10 38 10,7 25,3 AH550-901 Joint for glass structural Dev. anod.: 119 mm Dev. mech.: 0 mm Weight: 0,795 kg/m AH550-902 Spacer for glass structural Dev. anod.: 114 mm Dev. mech.: 0 mm Weight: 0,348 kg/m AH550-903 Spacer for glass structural Dev. anod.: 97 mm Dev. mech.: 0 mm Weight: 0,656 kg/m 20 14.7 3.5 23.2 AH550-5150002 Glass support for flap window (structural cw) Dev. anod.: 83 mm Dev. mech.: 0 mm Weight: 0,261 kg/m April 2009

Variable angle profiles Profiles 41 44.1 29.5 50.0 AH550-5113001 Column addition for variable corner Dev. anod.: 404,4 mm Weight: 1,228 kg/m Dev. mech.: 80,3 mm AH550-5113002 Pressure plate addition for 45 o Dev. anod.: 255,7 mm Weight: 0,794 kg/m Dev. mech.: 77 mm 34.4 AH550-5113003 Pressure plate addition for 60 o Dev. anod.: 217,5 mm Weight: 0,665 kg/m Dev. mech.: 57,6 mm AH550-5113004 Pressure plate addition for 150 o Dev. anod.: 353,7 mm Weight: 1,013 kg/m Dev. mech.: 81 mm AH550-5113005 Cover for pressure plate addition for 150 o Dev. anod.: 104 mm Weight: 0,163 kg/m Dev. mech.: 29 mm AH550-5113006 Column addition for for 150 o Dev. anod.: 83,4 mm Weight: 0,203 kg/m Dev. mech.: 11,3 mm www.balkan.gr

42 Profiles for accessory parts Profiles 44.8 AH550-5182160 Profile for reinforcement 902 00230 in mullion profile AH550-5114160 Weight: 3,20 kg/m 45.2 AH550-5182140 Profile for reinforcement 902 00229 in mullion profile AH550-5114140 Weight: 2,85 kg/m 45.2 AH550-5182120 Profile for reinforcement 902 00228 in mullion profile AH550-5114120 Weight: 2,52 kg/m AH550-5182100 Profile for reinforcement 902 00227 in mullion profile AH550-5114100 Weight: 2,23 kg/m 45.2 62.7 82.7 102.7 122.7 142.7 AH550-5182080 Profile for reinforcement 902 00226 in mullion profile AH550-5114080 Weight: 1,88 kg/m 45.2 April 2009

Profiles for accessory parts Profiles 43 44 44,4 161,2 180 44,4 44 AH550-5182180 Profile for reinforcement in mullion profile AH550-5114180 Weight: 3,921 kg/m AH550-5182200 Profile for reinforcement in mullion profile AH550-5114200 Weight: 4,317 kg/m www.balkan.gr

44 Profiles for accessory parts Profiles 53,1 10 64,5 45.8 R18.9 29 AH550-5184999 T-Connector for transom AH550-5122080 Weight: 2,56 kg/m AH550-5184346 T-connector profile, variable for transom AH550-5122039 - AH550-5122139 for production of inclined transoms Weight: 1,562 kg/m AE003-000001-00 Fast connector / transom Dev. anod.: 268 mm Dimension: 40mm AH550-5184002 Fast connector / mullion Dev. anod.: 98 mm Weight: 0,518 kg/m April 2009

Profiles for accessory parts Profiles 45 AH550-5184046 T-Connector for transom AH550-5122039 - AH550-5122139 Dev. anod.: 217 mm Weight: 1,598 kg/m AH550-5184045 T-Connector for transoms AH550-5122159 Dev. anod.: 215 mm Weight: 1,574 kg/m AH550-5184044 T-Connector for transoms AH550-5122199 Dev. anod.: 214 mm Weight: 1,561 kg/m AH550-5184001 Fast connector / transom Dev. anod.: 193 mm Weight: 1,307 kg/m www.balkan.gr

46 Profiles for accessory parts Profiles 44 AH550-5182000 Mounting accessory for 28 Weight: 10,357 kg/m 8 150 68 32 32 180 April 2009

Accessories Accessories 47 10 3 903 271 Joint sealing tape 10 x 3 mm Roll 10 m impregnated 20 W51 5001 Glazing support for sash with clamped glazing 125 mm long (from profile W51 56039) 39 903 00033 Glazing support for sash with bonded glazing 125 mm long (from profile W51 56053) 885276 39.6 903 00035 Glazing support for fixed glazing 125 mm long (from profile W51 56042) 884454 12 0.6 903 00040 Butyl adhesive tape Roll 30 mm double-sided 38 0.6 903 00041 Butyl adhesive tape Roll 10 mm - for the roof area Connecting foil 5±0 Width 7.5 Keder Waterstrip 1 SG tan EPDM sealing strips to DIN 7864 as facade gasket For sealing between facade elements and inner supporting structure (not water vapour-tight) 904 855 Sealing strip. EPDM 150 mm wide with weatherstrip 20 m on roll 904 857 Sealing strip. EPDM 250 mm wide with weatherstrip 20 m on roll 904 859 Sealing strip. EPDM 300 mm wide with weatherstrip 20 m on roll 904 861 Sealing strip. EPDM 330 mm wide with weatherstrip 20 m on roll 904 864 Sealing strip. EPDM 500 mm wide with weatherstrip 20 m on roll 905 429 SG adhesive FA for EPDM sealing strips Required adhesion surface width 80-100 mm Adhesive consumption 90-110g (= approx. 0.08-0.10 ltr.) per running metre Tubular plastic bag (standard tubes) of 0.6 ltr (approx. 700 g) 905 436 SG cleanser T for soiled surfaces (grease) Container with (approx. 850 g) CAUTION! During adhesion, the instructions and hazard warnings of the manufacturer must be strictly observed! www.balkan.gr

48 Glass thickness chart Glass thickness Insulator Rabbed width Inner gasket Outer gasket Torx screw 12 mm PK 391 25 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 900 = 35 mm 14 mm PK 391 25 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 900 = 35 mm 16 mm PK 391 25 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 900 = 35 mm 18 mm PK 391 25 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 900 = 35 mm 18 mm PK 393 31 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 902 = 45 mm 20 mm PK 393 31 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 902 = 45 mm 22 mm PK 393 31 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 902 = 45 mm 24 mm PK 393 31 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 902 = 45 mm 24 mm PK 392 37 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 901 = 50 mm 26 mm PK 392 37 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 901 = 50 mm 28 mm PK 392 37 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 901 = 50 mm 30 mm PK 392 37 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 901 = 50 mm 28 mm PK 390 41 mm 904 00035 = 9 mm 904 00315 = 4 mm 906 903 = 55 mm 30 mm PK 390 41 mm 904 00030 = 7 mm 904 00315 = 4 mm 906 903 = 55 mm 32 mm PK 390 41 mm 904 00025 = 5 mm 904 00315 = 4 mm 906 903 = 55 mm 34 mm PK 390 41 mm 904 00020 = 3 mm 904 00315 = 4 mm 906 903 = 55 mm 904 00040 904 00035 904 00030 904 00025 904 00020 904 00315 14 9 7 5 3 4 Rabbet dimensions CAUTION! When using sealing washers, observe the screw length and the new screw insertion depth!! Glass thickness charts for sashes, please refer to the respective series for the sash used. Mullion drawn rotated through 90 April 2009

Seals 49 3 24.5 24,5 AE004-904015-00 015 Stop gasket EPDM, black 5.8 7 AE004-000003-00 Gasket for standard flap window EPDM, black AE004-904001-00 520 Central Gasket, gasket external EPDM, Silicone, black grey 904 AA205-101-00 540 Gasket, external for flap window EPDM, black AE004-000001-00 Sealing cord Gasket for structural EPDM, black EPDM, black 14 10 Glazing max. 10 angle 12 7 asymmetric 10 4 7 asymmetric 7 12 Glazing max. 10 angle AE004-904000-40 00040 AE004-904940-00 940 AE004-904945-00 945 Gasket, internal Gasket, external Gasket, internal EPDM, black EPDM, black EPDM, black 3 5 7 7 7 7 AE004-904000-20 00020 Gasket, internal EPDM, black AE004-904000-25 00025 Gasket, internal EPDM, black AE004-000-30 904 00030 Gasket, internal EPDM, black 9 4 4 7 7 4.8 4,8 5 5 AE004-000002-00 Gasket for structural flap window EPDM, black 4 2,6 19.7 5.9 5,3 20.6 AE004-904000-35 00035 Gasket, internal EPDM, black www.balkan.gr AE004-904000-75 00075 Gasket, internal EPDM, black AE004-904003-15 00315 Gasket, external EPDM, black

50 Screws of stainless steel Screws AE010-906116-00 Cylinder screw AE010-906270-00 Countersunk screw AE010-906609-00 Countersunk screw Roof window hinges for connecting pin for Τ-joints AE010-906752-00 Fillister-head self-tapping screw AE010-906759-00 Countersunk self-tapping screw AE010-906761-00 Countersunk self-tapping screw with cross head with cross head with cross head 25 n3.5 AE010-000006-00 Fillister-head self-tapping screw B3,5X25 with cross head AE010-906762-00 Fillister-head self-tapping screw B4.2X25 with cross head AE010-000004-00 Countersunk self-tapping screw B4.8X25 with cross head AE010-906770-00 Fillister-head self-tapping screw B4.8X32 with cross head AE010-906777-00 Self-tapping screw AE010-906779-00 Fillister-head self-tapping screw AE010-906782-00 Countersunk self-tapping screw with cross head with cross head with cross head April 2009

Screws 51 Ø DIN 7982 ISO 7050 906 797 Countersunk self-tapping screw B 4,8 x 9,5 with cross head AE010-000005-00 906 900 FWB facade screw Torx T25, with special thread Ø 5,5x35mm Sealing washer with rubber coat (EPDM) for screw Ø 4,8 for pressure profiles 60 AE010-000001-00 AE010-906901-00 901 AE010-000002-00 AE010-000003-00 FWB facade screw FWB facade screw FWB facade screw FWB facade screw Torx T25, with special Torx T25, with special Torx T25, with special Torx T25, with special thread thread thread thread Ø 5,5x45mm Ø 5,5x50mm Ø 5,5x55mm Ø 5,5x60mm Accessories 905 561 Connecting pin for the connection with slide pieces AE009-905150-00 905 AE009-905160-00 905 Roll pin, AI Roll pin, AI for corner joints for T-joints www.balkan.gr

52 Accessories Screws AE005-000001-00 Plug decorative for AH550-5063098 Cut?when?use?insulator?AE013-000001-00 use AE005-000005-02 Fold ventilation black, for Cut?when?use?insulator?AE013-000002-00 use Fill?with?silicone Fill?with?silicone AE005-000006-02 Seal piece for dilatation Use?screw?AE010-906777-00 screw 18 AE013-000006-00 Square tube 24 April 2009

Accessories Accessories 53 AE013-929001-00 (PK 390) Insulator profile 30 mm 26 Rabbet dimensions Plastic AE013-000002-00 (PK 392) Insulator profile 26 mm Plastic 22 Rabbet dimensions AE013-000001-00 (PK 393) Insulator profile 20 mm 16 Rabbet dimensions Plastic AE013-000003-00 (PK 391) Insulator profile 14 mm Plastic 10 8 20 AE011-929790-00 (PK 79) T-profile for sealing elements Plastic 12 901 00520 33 In sash area with clamped glazings, sash profile W 51 50053 AE013-929036-20 (PK 426) Insulating and supporting profile Plastic www.balkan.gr

54 Corner connectors for flap window Curtain Wall system for faades and roofs Corner connector Β A Corner connector A. AE001-000003-00 B. ΑΑ001-022-00 for profile AH550-5150003 Connection with 5g adhesive 905 405 press AT038-015-00 Corner connector AE001-000004-00 for profile AH275-280 Connection with 5g adhesive 905 405 Press AT038-015-00 April 2009

Corner connector Profiles Profile 75030 60030 75030 901 569 901 458 901 459 for pinning Corner connectors 60,2 Roll pin 905 160 8,5 18 7 60 4 5 Roll pin 905 140 With drilling templates 907 229 and 907 00469 55 Corner connector 901 569 for profile 75030 Connection with 2 roll pins 905 160 and 5g adhesive 905 405 with drilling template 907 229 and drilling template 907 00469 Corner connector 901 458 for profile 75030 Connection with 2 roll pins 905 140 and 2g adhesive 905 405 with drilling template 907 229 and drilling template 907 00469 Pressta corner connector 901 459 for profile 75030 Connection with 2g adhesive 905 405 Corner connector for roof window The corner connectors No.: 901 595 / 605 / 635 / 645 are illustrated with the corresponding profiles. Corner connector 901 00245 Profiles 75027 n4 5,2 n7 Roll pin Roll pin 905 140 905 150 for profile 75027 Connection with 2 roll pins 905 150 and 5g adhesive 905 405 Drilling template 907 00347 8,3 Corner connector 901 00250 for profile 75027 Connection with 2roll pins 905 140 and 2g adhesive 905 405 901 00250 901 00251 pinning 901 911 Drilling template 907 00347 Alternatively: Pressta corner connector 901 00251 With drilling templates 907 00347 for profile 75027 Reinforcement angle bracket 901 911 for profile 75027 901 00245 Connection with 5g adhesive 905 405 www.balkan.gr

56 Corner connector sash W51 50053 (using roll pin) Corner connector Drilling template The corner connector must be installed with adhesive 905 405 The cut surfaces must be sealed. Cutting length 45,4 mm Drilling template Sash cutting dimension = Distance between centres + 1 mm Reinforcement angle bracket of TF 481 in the corner area of insulating profile PK 426 Article No. 901 00520 April 2009

T-connection T-connection half transom to half mullion 57 T-connector Drilling template axis profile contour drawn rotated through 90 for illustration of the line course T-connector Distance between centres Mullion profile Drilling template profile Countersink bores Mullion profile Distance between centres T-connector cutting dimension = Distance between centres +20mm If necessary: Tapered roll pin ISO 8745-5x20-St (stainless steel) www.balkan.gr

58 Cutting point, mullion corner, vertical with 190, symmetrical Glazing bar T-connector T-connection Drilling template profile Mullion profile Glazing bar T-connector If necessary: Tapered roll pin ISO 8745-5x20-St (stainless steel) contour drawn rotated through 90 for illustration of the line course contour drawn rotated through 90 for illustration of the line course profile Mullion profile T-connector Drilling template Distance between centres cutting dimension = Distance between centres +20mm April 2009

T-connection T-connection transom to mullion 59 Schematic view Further details on the following pages of the catalogue T-connector Mullion profile contour drawn rotated through 90 for illustration of the line course profile Drilling template T-connector cutting dimension = Distance between centres - 18mm Distance between centres www.balkan.gr

60 T-connection with T-connector T-connection T-connection schematic view T-connection with T-connector Butyl adhesive tape 12 x 50 mm from Article No. 903 00040 chamber Vertical load per T-connector max. 75 kg Drilling templates for transom end No. 907 00106 for mullion holes No. 907 00106 for T-connector to mullion No. 901 00101 Punching machine 900 94070 with die and punch for mullion No. 900 94036 Cut to length T-connector April 2009

T-connection T-connection transom (Level 2) to mullion (Level 3) 61 Mullion, vertical Level 3 Mullion, vertical Level 3, Level 2, Level 2 Butyl adhesive tape of 903 00040 Punching machine 900 94070 with tool 900 94036 Butyl adhesive tape of 903 00040, horizontal Level 2 www.balkan.gr

62 T-connection transom (Level 2) to mullion (Level 3) Scale 1:2 T-connection 904 00040 April 2009

T-connection T-connection transom (Level 2) to mullion (Level 3) 63 Scale 1:2 W90 71010 www.balkan.gr

64 T-connection transom (Level 2) to mullion (Level 3) Mullion T-connection of profile 902 00202 T-connector W51 22039 to mullion W51 14 *** Connection with 2 roll pins 905 160 2 screws 906 752 5 g adhesive 905 405 Drilling template 907 00106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile Mullion, Level 3 Mullion of profi le, Level 2 902 00203 T-connector W51 22054 to mullion W51 14 ** Connection with 2 roll pins 905 160 2 screws 906 752 5g adhesive 905 405 Drilling template 907 00106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile April 2009

T-connection T-connection transom (Level 2) to mullion (Level 3) 65 902 00204 T-connector W51 22079 to mullion W51 14080 Connection with 2 roll pins 905 160 2 screws 906 752 10g adhesive 905 405 Mullion Drilling template 907 00106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical of profi le Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile 902 00207 T-connector W51 22099 to mullion W51 14100 Connection with 2 roll pins 905 160 2 screws 906 752 15g adhesive 905 405 Drilling template 907 00106 Bores in horizontal transom for screws and roll pins Mullion Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile of profi le www.balkan.gr

66 T-connection T-connection transom (Level 2) to mullion (Level 3) 902 00206 T-connector W51 22119 to mullion W51 14120 Connection with 2 roll pins 905 160 2 screws 906 752 20 g adhesive 905 405 Mullion Drilling template 907 00106 Bores in horizontal transom for screws and roll pins of profi le Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile 902 00207 T-connector W51 22139 to mullion W51 14140 Connection with 2 roll pins 905 160 2 screws 906 752 20 g adhesive 905 405 Drilling template 907 00106 Bores in horizontal transom for screws and roll pins Mullion Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors 31.0335.08 of profi le Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile April 2009

T-connection T-connection transom (Level 2) to mullion (Level 3) 67 902 00208 T-connector W51 22159 to mullion W51 14160 Connection with 2 roll pins 905 160 2 screws 906 752 30 g adhesive 905 405 Drilling template 907 00106 Bores in horizontal transom for screws and roll pins Mullion Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile of profile 902 00209 T-connector W51 22179 to mullion W51 14180 Connection with 2 roll pins 905 160 2 screws 906 752 35 g adhesive 905 405 Mullion Drilling template 907 00106 Bores in horizontal transom for screws and roll pins 31.0335.09 of profile Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile www.balkan.gr

68 T-connection transom (Level 2) to mullion (Level 3) Mullion T-connection of profile W51 84046 T-connector W51 22* to mullion W51 14* Connection with 2 roll pins 905 160 1 screws 906 752 35 g adhesive 905 405 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile Mullion Level 3 52 50,4 37,8 Mullion Pfosten 16 36 Level 2 T-connector W51 22* to mullion W51 14* Connection with 2 roll pins 905 160 2 screws 906 752 35 g adhesive 905 405 Drilling template 90700106 Bores in horizontal transom for screws and roll pins of profile W51 84046 Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile April 2009

T-connection T-connection transom (Level 1) to transom (Level 2) (1) 69 T-connector of profile W51 84046 902 00216 T-connector W 51 21077 to transom W 51 22079 8,3 13,7 65,5 36 15,6 Connection with 2 roll pins 905 160 2 screws 906 752 10 g adhesive 905 405 Drilling template 907 00106 Bores in vertical transom for screws and roll pins 50.4 Lower recess only if the vertical transom is continued (2) Drilling template 907 00101 Bores in horizontal transom for attachment of the T-connectors 65,5 36 4,5 50,4 W51 21077 vertical 902 00216 36 15,6 W51 22079 horizontal T-connector of profile W51 84046, horizontal Punching machine 900 94070 with die and knife 900 94037 Punch-out on horizontal transom (2) 8,3 13,7 www.balkan.gr

70 Rapid Connection T-connection AE005-000002-02 Plug transom cover AH550-22039 AH550-22059 AH550-22079 AE005-000003-02 Plug transom cover AH550-22099 1 AE005-000003-02 AH550-22119 AH550-22139 AH550-22159 AH550-5184002-00 2 AH550-5184001-00 4 3 AE010-000006-00 April 2009

Rapid Connection T-connection 71 17.1 W51 84001 W51 84002 10.9 76 T-connector W51 22119 to mullion W51 14*** 11.5 104 Connection with 2 screws 906 754 4 screws 906 761 1 plug transom cover AE005-000003-02 10 g adhesive 905 405 Drilling template 907 00106 Bores in vertical transom for screws and roll pins Drilling template 907 00101 Bores in horizontal transom for attachment of the T-connectors Mullion Level 3 10 43, horizontal Punching machine 900 94070 with die and knife 900 94037 Punch-out on horizontal transom 50.4 37.8 20.5 W51 84001 W51 84002 (with profile W90 71010) 22,5 T-connector W51 22119 to mullion W51 14*** 10 31.8 10.9 10.9 66.6 17,1 94.6 Level 2 Connection with 2 screws 906 754 4 screws 906 761 1 plug transom cover AE005-000003-02 10 g adhesive 905 405 Drilling template 907 00106 Bores in vertical transom for screws and roll pins Drilling template 907 00101 Bores in horizontal transom for attachment of the T-connectors, horizontal Punching machine 900 94070 with die and knife 900 94037 Punch-out on horizontal transom www.balkan.gr

72 T-connection transom (Level 2) to mullion (Level 3) T-connection 11.1 65.2 27 W51 84001 W51 84002 50.4 T-connector W51 22079 to mullion W51 14080 22 36 18.3 Connection with 2 screws 906 761 4 screws 906 777 1 plug transom cover AE005-000002-02 Mullion W51 14080 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors W51 84002 W51 84001 Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile W51 22079 W51 84001 W51 84002 11. 84.2 27 T-connector W51 22099 to mullion W51 14100 22 56 17.3 50.4 Connection with 2 screws 906 761 4 screws 906 777 1 plug transom cover AE005-000003-02 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Mullion W51 14100 Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors W51 84002 Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 W51 84001 Punch-out on mullion profile W51 22099 April 2009

T-connection T-connection transom (Level 2) to mullion (Level 3) 73 11.1 104,0 27 W51 84001 W51 84002 50.4 T-connector W51 22119 to mullion W51 14120 22 76 17.1 Connection with 2 screws 906 761 4 screws 906 777 1 plug transom cover AE005-000003-02 Mullion W51 14120 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors W51 84002 W51 84001 Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile W51 22119 11. 124,0 27 W51 84001 W51 84002 50.4 T-connector W51 22139 to mullion W51 14140 22 Mullion W51 14140 96 17.1 Connection with 2 screws 906 761 4 screws 906 777 1 plug transom cover AE005-000003-02 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors W51 84002 W51 84001 Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile www.balkan.gr W51 22139

74 T-connection transom (Level 2) to mullion (Level 3) T-connection 11.1 144,0 27 W51 84001 W51 84002 50.4 T-connector W51 2259 to mullion W51 14160 22 116 17.1 Connection with 2 screws 906 761 4 screws 906 777 1 plug transom cover AE005-000002-02 Mullion W51 14160 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors W51 84002 W51 84001 Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile W51 22159 11.6 162,5 27 W51 84001 W51 84002 T-connector W51 22179 to mullion W51 14180 22 136 16.1 50.4 Connection with 2 screws 906 761 4 screws 906 777 1 plug transom cover AE005-000003-02 Mullion W51 14180 Drilling template 90700106 Bores in horizontal transom for screws and roll pins Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors W51 84002 W51 84001 Mullion profile, vertical Punching machine 900 94070 with die and knife 900 94036 Punch-out on mullion profile W51 22179 April 2009

Reinforcement Reinforcement, vertical butt joint mullion/mullion 75 Reinforcement Number and spacing of the bolts according to statics requirements 902 00226 Reinforcement for mullion W 51 14080 Length 300 mm as bar 6,0 m long No.: W51 82080 300 902 00227 Reinforcement for mullion W 51 14100 Length 300 mm as bar 6,0 m long No.: W51 82100 902 00228 Reinforcement for mullion W 51 14120 Length 300 mm as bar 6,0 m long No.: W51 82120 902 00229 Reinforcement for mullion W 51 14140 Length 300 mm as bar 6,0 m long No.: W51 82140 25 905 561 906 830 902 00230 Reinforcement for mullion W 51 14160 Length 300 mm as bar 6,0 m long No.: W51 82160 4 Joint 906 270 M. 1:1 www.balkan.gr Shown in reduced size

76 Variable T-connection Variable T-connection, transom (Level 2) to mullion (Level 3) April 2009

Variable T-connection Variable T-connection, transom (Level 2) to mullion (Level 3) 77 902 00264 T-connector, variable W51 22079 to mullion W51 14080 Mullion Connection with 3 roll pins 906 770 1 screws 906 901 10 g adhesive 905 405 Insulator PK 390 Insulator PK 390 (level 2) Bores in the inclined transom for screws according to the angle Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion (level 3) 902 00265 T-connector, variable W51 22099 to mullion W51 14100 Mullion Connection with 3 roll pins 906 770 1 screws 906 901 15 g adhesive 905 405 Insulator PK 390 Insulator PK 390 (level 2) Bores in the inclined transom for screws according to the angle Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connectors Mullion (level 3) www.balkan.gr

78 Variable T-connection Variable T-connection, transom (level 2) to mullion (level 3) Mullion Insulator PK 390 Insulator PK 390 (level 2) 902 00266 T-connector, variable W51 22119 To mullion W51 14120 Connection with: 3 screws 906 770 1 screw 906 901 20 g adhesive 905 405 Bores in the inclined transom for screws according to the angle Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connector Mullion (level 3) 902 00267 Mullion T-connector, variable W51 22119 To mullion W51 14120 Connection with: 3 screws 906 770 1 screw 906 901 25 g adhesive 905 405 Insulator PK 390 Insulator PK 390 (level 2) Bores in the inclined transom for screws according to the angle Drilling template 907 00101 Bores in vertical mullion for attachment of the T-connector Mullion (level 3) April 2009

Drilling template Drilling template 907 00101 - Schematic view Positioning of the template on the mullion profile 79 Positioning of the template on the disengaged mullion profile Mullion profile Level 2 Mullion profile Level 2 www.balkan.gr

80 Drilling template 907 00101 - Schematic view Positioning of the template on the mullion profile (2) Drilling template Positioning of the template on the disengaged mullion profile (2) Mullion profile Level 2 Mullion profile Level 2 Shim April 2009

Τ-connection T-connection transom / half-mullion to half mullion 81 39.5 30 T-connector 902 00185 37.3 5.2 906 609 Drilling template 907 00027 In order to illustrate the course of the line, the profiles are drawn rotated through 90 T-connector 902 00186 Drilling template 907 00028 Riegelprofile profiles 43.5 37.9 www.balkan.gr

82 Cutting points Cutting point, horizontal - cutting of transom W51 22080 axis Axis of the bore Glazing transom W51 50080 vertical above and below sash panels W51 22080 Horizontal Glazing transom W51 50080 vertical above and below sash panels Cutting allowance W51 22080 Horizontal Mullion W51 15080 vertical In order to illustrate the course of the line, the profiles are drawn rotated through 90 o T-connector 902 00185 Mullion W51 15080 vertical Mullion W51 15080 vertical Cutting allowance = Matrix dimension + 20 mm April 2009

Installation of insulator Installation of insulator PK 426 in sash area (clamped glazing) 83 Corner connector 901 00520 from profile TF 481 Axis Notching Axis Notchings in the horizontal parts PK 426 www.balkan.gr

84 16 25 1 5.... Cut lengths Cutting to length Cut lengths (L) 1 Cover profile. L = A - 52 mm 1 5 Cover profile. L = A - 60 mm 5 25 Insulator profile + transom profile. L = A - 18 mm 25 PK 390 Cover profile L = A - 52 mm Cover profile L = A - 60 mm L = A - 18 mm PK 390 L = A - 18 mm 61020 904 00040 25 57008 Insulator profile profi le profi le 904 00030 57008 61015 Axis (A) Axis (A) 9 9 Mullion Axis (A) Axis (A) Pressure profile Axis (A) Pressure profile PK 390 25 April 2009

Facade connections Facade connections 85 Schematic representation of various possibilities Movable bearing Movable bearing Movable bearing Fixed bearing Fixed bearing Fixed bearing Movable bearing Movable bearing Movable bearing Fixed bearing Fixed bearing Fixed bearing www.balkan.gr

86 Overview of cutting points Cutting points Continuous transom Level 2 Mullion, level 3 Mullion, level 3 Mullion, level 3, level 1 between the horizontal transoms, level 2 Mullion, level 3 Continuous transom Level 2 Level 2 Mullion Mullion, vertical Level 3, horizontal Level 2, vertical Level 1 April 2009

Cutting points Cutting point, mullion, vertical (Level 3) Further mullion profiles up to 200 mm installation depth, see profile illustrations 87 Further glazing thicknesses, see Glazing thickness chart www.balkan.gr

88 Cutting points Cutting point, mullion corner, vertical with 160, symmetrical contour drawn rotated through 90 for illustration of the line course CAUTION! Due to the excessive angle of the glazings, the vertical pressure profiles may only be tightened until they fulfil their sealing function and not too tightly. April 2009

Cutting points Cutting point, mullion corner, vertical with 190, symmetrical 89 contour drawn rotated through 90 for illustration of the line course CAUTION! Due to the excessive angle of the glazings, the vertical pressure profiles may only be tightened until they fulfil their sealing function and not too tightly. www.balkan.gr

90 Cutting point, transom, horizontal (Level 2) Cutting points Drainage of the transom The transom is drained via at least 2 bores (dia. 6 mm) or slots 20x5 drilled in the retaining profile and cover strip Distance max. 600 mm Distance between centres Further glazing thicknesses, see Glazing thickness chart Glazing support Nr. 903 00035 drainage At least 2 holes Φ6 mm or slots 20x5 mm Further transom profiles in steps of 20 mm up to an installation depth of 198.5 mm - see profile illustrations April 2009

Cutting points Cutting point, vertical, sashes with bonded glazings 91 204,6 28 4 64 9 AH275-280 AH550-5063098 57010 80 35 97,6 8 2 AH550-5150003 W5114080 17,3 43,1 50 110,4 www.balkan.gr

92 Cutting point, horizontal, sashes with bonded glazings Cutting points 137 1.5 78.5 37 15 5 7 26 4 66.5 19.5 4.5 Horizontal cut 42 42 Flgelzuschnitt = Rasterma + 1 mm 66.5 19.5 4.5 Riegel W51 22080 61015 15 27 27 53 15 122 PK 426 30 34 PK 426 57010 61020 15 5 57010 61020 Riegel W51 22079 11 904 00030 61015 50 15 The glazing planes in the window sash 15 and in the fi xed panel are fl ush 11 50 Sash size = Grid dimension + 1mm Riegel W51 22079 Riegel W51 22080 W51 50053 W51 50053 W51 15080 W51 15080 W51 50015 W51 50015 904 00030 904 00315 904 00100 CAUTION! Min. grid dimension = 750mm 904 00100 904 00075 904 00075 904 00315 April 2009

Cutting points Cutting point, vertical, sashes with bonded glazings Vertical cut 93 Recess Recess Sash size = Grid dimension + 1 mm Recess 10 mm dia. for drainage Recess The glazing planes in the window sash and in the fixed panel are flush www.balkan.gr

94 Cutting point, horizontal, sashes with bonded glazings Cutting points 1.5 78.5 132 5 28 4 12 904 00025 904 00315 W51 14080 PK 390 50 AE004-000003-00 AH550-5150003 11.8 AA205-101-00 5.5 60.4 Horizontal cut 11.8 50 43.1 5.5 11.8 17 34.2 43.1 50 1.5 AH275-280 2 8.5 AH275-280 AH550-5150003 W51 14080 64 119 904 00035 9 904 00035 28 4 12 11.8 34.2 15 10 60.4 25 The glazing plane in the window sash is offset from the fixed panel! April 2009

Cutting points Cutting point, vertical, sashes with bonded glazings 95 3 12 4 28 5 78.5 132 1.5 904 00315 904 00025 W51 22079 PK 390 AE004-000003-00 11.8 AH550-5150003 AA205-101-00 Vertical cut 904 00035 904 00035 AA205-101-00 W51 56042 AH275-280 2 AH275-280 AH550-5150003 W51 22079 PK 390 904 00315 904 00025 43.1 60.4 50 60.4 10 15 11.8 34.2 34.2 50 12 4 28 64 119 17 17 8.5 1.5 11.8 5.5 50 43.1 5.5 11.8 The glazing plane in the window sash is offset from the fixed panel! www.balkan.gr

96 Cutting point, horizontal, sashes with bonded glazings Cutting points 1.5 78.5 5 32 Horizontal cut 50 43.1 5.5 11.8 11.8 5.5 43.1 50 W51 AH550-5114080 14080 AH550-5150003 W51 50003 AH275-280 14 2 AH275-280 AH550-5150003 AH550-5114080 W51 14080 64 904 00035 904 00035 904 00025 904 00025 904 00035 904 00035 9 AE004-000001-00 28 10 10 12.6 48.3 48.3 12.6 10 10 85.4 85.4 The glazing plane in the window sash is offset from the fixed panel! April 2009

Cutting points Cutting point, vertical, sashes with bonded glazings 97 Vertical cut The glazing plane in the window sash is offset from the fixed panel! www.balkan.gr

W51 22119 98 Section of A turning mode (45o angle) Cutting points AH550-5113002 61012 57010 AH550-5114100 57010 61012 90 W51 22079 W51 22079 17,0 50,0 44,1 AH550-5113002 61012 57010 AH550-5114100 61012 57010 W51 14100 W51 22079 135 April 2009

Section of A turning mode (60o angle) Cutting points 99 34,3 7,3 50,0 7,3 34,3 AH550-5113003 61012 57010 61012 57010 AH550-5114100 W51 22079 W51 22079 120 34,3 7,3 50,0 61012 57010 AH550-5113003 61012 57010 AH550-5114100 W51 22119 W51 22079 150 www.balkan.gr

100 Section of A turning mode (150o angle) Cutting points 16 10 29 10 16 AH550-5113004 15 11,3 10,2 32 AH550-5114104 W51 14120 150 April 2009

Cutting points Cutting point, horizontal, below or above the window sash 101 7 26 4 50 50 15 Riegel W51 22079 Horizontal cut 35 15 35 Riegel W51 22080 W51 50080 Riegel W51 22080 W51 50080 80 137 7 PK 390 26 37 PK 390 4 15 5 Riegel W51 22079 61015 61015 W51 15080 W51 15080 Dehn band Dehn band 904 00030 11 11 11 11 Vulcanised frame 904 00315 50 50 904 00030 61020 61020 Vulcanised frame 904 00315 57010 57010 The glazing plane in the window sash is offset from the fixed panel! www.balkan.gr

102 Cutting points Cutting point, horizontal, sash/fixed glazing 137 1.5 78.5 37 15 7 26 4 5 66.5 W51 22079 Horizontal cut 19.5 42 5 50 1.5 78.5 37 15 5 4.5 Mullion W51 14080 W51 22079 W51 22079 904 00100 906 901 W51 15080 137 904 00030 7 26 904 00030 PK 390 PK 426 904 00315 4 904 00315 61015 61020 W51 50053 W51 50015 61020 11 11 11 50 50 57010 57010 The glazing plane in the window sash is offset from the fixed panel! 15 W51 22080 904 00075 61015 53.1 48.9 122 6.1 30 4 15 5 April 2009

Cutting points Cutting point, horizontal, below or above the window sash 103 1.5 78.5 37 15 5 137 7 26 4 906 901 1.5 78.5 137 37 7 26 PK 390 4 15 5 35 11 50 15 50 11 50 11 50 Riegel W51 22079 PK 390 61020 Horizontalschnitt Horizontal cut Mullion Pfosten W51 14080 Riegel W51 22079 Riegel W51 22079 57010 61015 57010 11 61015 W51 50080 W51 15080 Riegel W51 22080 904 00030 Dehn band 904 00030 904 00315 61020 904 00315 Expansion strip 7 26 4 80 37 15 5 www.balkan.gr 137

104 Cutting points, inclined glazing Cutting points Manufacture from PK 79 Purlin of transoms Spars of mullions to meet static requirements of PK 79, 50 mm long Purlin of transoms April 2009

Cutting points Cutting point, frame insert, Series RG 75 block window for facade 105 Mullion Axis www.balkan.gr

106 Cutting point, frame insert, Series RG 75 for facade Door opening inwards Cutting points Mullion Axis April 2009

Cutting point, frame insert, Series RG 75 for facade Door opening outwards Cutting points 107 Mullion Axis Positioning aid for 6 mm groove, twisted and not pinned Drilling template www.balkan.gr

108 Cutting point, vertical facade, top Design draft Attic cover Cutting points Sealing tapes Ventilation Air inlet in mullion area Mullion Ventilation Drainage Air inlet in the transom area Mullion Sliding profile Cross section April 2009

Cutting point, vertical facade, top Cutting points 109 Design draft Sealing tapes Ventilation Air inlet in mullion area Mullion Back-ventilated LM cold facade Suspended ceiling Ventilation Drainage Air inlet in the transom area Mullion Sliding profile Cross section www.balkan.gr

110 Cutting point, vertical facade, in front of a ceiling Design draft Cutting points Mullion Finished floor level Ventilation Drainage Air inlet in the transom area Anchoring and - Quantity and - Distribution of the bolts: According to statics Mullion butt joint with reinforcement Suspended ceiling Ventilation Drainage Air inlet in the transom area Sliding profile Mullion April 2009

Cutting point, vertical facade, lateral Cutting points 111 Design draft Mullion Sliding profile www.balkan.gr

112 Cutting point, vertical facade, bottom Cutting points Horizontal cut Design draft Mullion Sliding Profile Vertical cut Sealing tape Finished floor level Ventilation Drainage Air inlet in the mullion area Ventilation Drainage Air inlet in the mullion area April 2009

Cutting point, vertical facade, bottom Cutting points 113 Horizontal cut Mullion Design draft Vertical cut L profile Sealing tape Finished floor level Ventilation Drainage Air inlet in the mullion area Ventilation Drainage Air inlet in the mullion area www.balkan.gr

BALKAN NETWORK GREECE - BALKAN SA www.balkan.gr Head Office: Athens 11th km Nat.Road Athens-Lamia, 144 52 Metamorphosi Tel.: +30 210 2810 030, Fax: +30 210 2845 025 e-mail: info@balkan.gr Iraklio: +30 2810 370555-6, Fax: +30 2810 311 400 Larissa: +30 2410 555 641-2, Fax: +30 2410 288 919 Τhessaloniki: +30 2310 753 454, Fax: +30 2310 753 455 Τhiva: Tel.: +30 22620 72001-4, Fax: +30 22620 71293 Extrusion Industry 79th km Nat. Road Athens-Lamia, Ipato Thivon Tel.: +30 22620 72001-4, Fax: +30 22620 71293 e-mail: factory@balkan.gr ROMANIA - BALKAN RO www.balkanro.ro Head Office: Bucharest B-dul Iuliu Maniu 333, Sector 6 Tel.: +40 213 170 695-7-8, Fax: +40 213 160 699 e-mail: balkanro@balkanro.ro Alba Iulia: +40 258 810 241, Arad: +40 257 288 588, Bacau: +40 234 562 620 Βrasov: +40 286 549 904, Cluj-Napoca: +40 264 415 512, Constanta: +40 241 559 850 Craiova: +40 251 483 323, Iasi: +40 232 244 055, Τimisoara: +40 256 296 114 DEALERS Galati: Alprovest, tel/fax: +40 236 458 038, Pitesti: Conarg, tel/fax: +40 248 610 089 Satu Mare: Neptun, tel/fax: + 40 261 841 930, Sibiu: Roa Design, tel/fax: +40 269 214 325 Ploiesti: Rolir, tel/fax: +40 244 225 170 UKRAINE - BALKAN UA Head Office: Kiev Moskovsky Av. 6 Tel./Fax: +38 044 464 4947/7858 Κharkov: +380 57 757 5161-2 Odessa: +380 482 328 402, 335 654, 0487 773 389 BULGARIA - BLK BG www.blk-bg.com Ηead Office: Sofia 8 Malashevska Str. 1202 Tel.: +359 2 936 6652/91, Fax:+359 2 936 6735 e-mail: office@blk-bg.com CZECH REPUBLIC ALUMONT BUILDING A.S. DEALER Hradni-Slazska 27/37, 710 00 Ostrava Tel./Fax: +420 777 800333 e-mail: alumont@alumont.cz www.alumont.cz RUSSIA MGM LTD DEALER Promzona 16 Str.-Armavir, 352916 Krasnodar Tel./Fax: +7 86137 58100 e-mail: armoz@inbox.ru BELARUS SOL-FARM DEALER Kalvariyskaya 60/2H, 220073 Minsk Tel./Fax: +37517 204 22 25 e-mail: sol-farm@mail.ru