W & Y Series Split Shaft Transmission Operation & Maint.

Similar documents
C21 Series Transmission Operation and Maintenance Instructions

Waterous S100 Single Stage Pump

Shift Units Installation Instructions

With PA Series Transmission: S101 Series Midship Pumps: With C20 Series Transmission:

K, T, TK, TA and KC Series Operation and Maintenance Instructions

Operation and Maintenance. S100 Series Centrifugal Fire Pumps. Table of Contents. Visit us at F /22/02 6/21/18

With WB Series Transmission: With PA Series Transmission: With K Series Transmission:

TC20 Chain Driven Power Take-Off Overhaul Instructions

C10 Transmission Assembly Service Parts List

CM, CMU, CS, CSU Separable Impeller Shaft 2, 3 CXV, CXS Non-Separable Impeller Shaft 4, 5. Input and Output Shaft.

HL Series Centrifugal Fire Pumps Operation and Maintenance Instructions

Table of Contents Illustrations

Troubleshooting the Transmission Hydraulic System

32 quarts Transmission Allison HT 740 Automatic Fluid

CL Series Centrifugal Fire Pumps Installation Instructions

Main Fire Pump Engagement. Shifting Into Pump 2006 / 2007 KME

HL Series Centrifugal Fire Pumps Installation Instructions

Operation and Maintenance. CG Series Centrifugal Fire Pumps. Illustrations

PowerLevel s e r i e s

HYDRAULIC TABLE OF CONTENTS. CX Hammer with PLC EMERGENCY PUMP OPERATION

S200-P Series Centrifugal Fire Pumps Operation and Maintenance Instructions

Troubleshooting The Transmission Hydraulic System

Principals of Operation... 1 Rotary Vane Priming Pump VPE and VPES... 2 Rotary Vane Priming Pump VPO and VPOS Priming Valve...

Troubleshooting Guide

Pump Service Testing

WARM ENGINE STARTING PROCEDURE

Items Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd

Installation. Installation. 12. System Diagram... 10

Fisher 657 Diaphragm Actuator Sizes and 87

Operation Guide. Operation Guide. Winnebago Hydraulic Leveling Systems by Kwikee. Introduction. Table of Content WARNINGS

CH-4 Series Fire Pumps Overhaul Instructions

SERVICE MANUAL Gearbox - Allison AT545 - Gearbox Installation

Operation and Maintenance. CS Series Centrifugal Fire Pumps. Table of Contents. Visit us at F /14/95

DIAGNOSIS AND TESTING Procedure revision date: 05/18/2000. SYMPTOM CHART TRANSMISSION, MANUAL Condition Possible Source Action

Auger Installation, Operation and Service Manual

200C II BRAKE SYSTEM

Introduction. General Information. Systems Operation

CP-1, CP-2, CP-2L & CPD-2 Series Overhaul

Table of Contents General Information Safety Message Classifi cation...2 Safety Notes...3 Terminology...4 Coupler Lifting Lug...

RELEASING PRESSURE IN THE HYDRAULIC SYSTEM,

Troubleshooting Guide

PRE CHECK DI 456. w/ Tachometer. w/o Tachometer. Hand held Tester AUTOMATIC TRANSMISSION (A340E, A340F) 2003 TOYOTA TACOMA (RM1002U) D10837 D00729

Driver Operator Aerials: Maintenance and Testing. 4 Skills Total. NFPA 1002, Standard for Driver Operator Professional Qualifications, 2014 Edition

BORG WARNER TRANSFER BOX

Eclipse GEN 2.0 CAFSystem, Model 150-ESECL as used with TC20 Series PTO Installation Instructions

Manual Transmission / Transaxle Power = Force (torque) X Speed (rpm)

Eclipse GEN 2.0 CAFSystem, Model 150-ECL CAFS PTO Kit Installation Instructions

Introduction... 2 Water/Foam Solution Distribution Components... 3, 4 Lubrication:

Bulletin: CLIB Date: February 4, Bulletin Type: Service. Topic: Eaton Clutch Performance Evaluation and Set-up

Troubleshooting Guide

CONTENTS. EMERGENCY PUMP USE Electric Pump...H-3 Manual Pump...H-5

Troubleshooting, Service Tips, And Major Improvements For Hydrostatic Transmissions (Special Edition){3200}

INSTALLATION MANUAL. MB-180, MB-210 and MB-210L Motor Brake INSTALLATION. Force Control Industries, Inc. DESCRIPTION OPERATION

Priming Systems Installation Instructions

KC Transmission Overhaul

TABLE OF CONTENTS. Tow Behind Bulk Bin Brake Release Procedure... H-3. General Hydraulic Repair Procedure... H-4

Westingh'ouse Steam Turbines-I. B (Rev. 3) GOVERNOR, GOVERNING VALVE

PO Box 645, Stockton, Missouri, FAX superiorgearbox.com

To increase the height of the trailer increase the length, to reduce the height, decrease the length of the link.

TORQUE CONVERTER. Section 2. Lesson Objectives. 6 TOYOTA Technical Training

HINO PTO INTERFACE PTO INSTALLATION AND OPERATOR S MANUAL KEEP IN VEHICLE. FOR Allison 2500 With CS6B-A67**-S3*H PTO

INSTALLATION MANUAL. MB-250, MB-280 and MB-320 Motor Brake INSTALLATION. Force Control Industries, Inc. DESCRIPTION OPERATION

Allison Lockup Controller

70001 and Clutch Rebuild Instructions

Oregon Fuel Injection

HYDRAULIC LEVELING SYSTEMS OPERATIONS MANUAL (For systems with touch pad part number , , , , or no number at all)

BRAKE SYSTEM, HYDRAULICALLY ACTUATED - 631G TRACTOR Cat Tractors with standard shoe/drum brakes

9/28/2018. Refrigeration compressor operation, maintenance and safety

CAUTION. Start & Stop Procedures. Section 1-2. Engine Oil Level

MGA and RGA SERIES SPLIT-SHAFT PTO DRIVE GEARBOX INSTALLATION MANUAL

Power Train. Chapter 5

SD Bendix Manual Slack Adjusters DESCRIPTION ADJUSTING MECHANISM OPERATION

OPERATORS MANUAL/INSTRUCTIONS/PARTS & SERVICE FOR MANUAL & ELECTRIC

SECTION 3.00 WARNING WARNING ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION

Operation and Maintenance Manual REMOTE DRIVE

Service Manual #67. Installation and Service Instructions 6000, 7000 & 8000 Series Magnetically Coupled Pumps

Max IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.

TIME LAG TEST Check the automatic transmission (each clutch, brake and gear) for wear.

DI 244 DIAGNOSTICS AUTOMATIC TRANSMISSION DIB30 01 PRE CHECK

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS

3 Phase Smart Controller

TroubleshootingGuide L6456 ECN

BRAKE E

COOKSON OWNER'S MANUAL

Track Drive Circuit - General System. Simplified Travel Circuit Diagrams: Neutral Controls Forward Travel Reverse Travel

Operation Guide. Hydraulic Leveling Systems #2000, #2010, #3000, and # Table of Content. Introduction

TroubleshootingGuide L6455 ECN

Installation Manual For ISL98, ISL03, ISL07, ISC07

Automated Control Electronics (ACE ) System Operation and Diagnostics

Kysor On/Off Rear Air Fan Drive

Diagnostic Procedures

Purging Air From Divider Block Lubrication Systems

Tech Note Truck 14 & 15.5 Twin Plate Cast Iron Type Installation Guidelines

AUTOMATIC CONTROL ROLLING DOOR OPENER

Model DFR 070/156/220 Rotary Actuator

Instruction Sheet. 1/2 HP Portable Electric Pumps SAFETY FIRST. L2062 Rev. F 02/ IMPORTANT RECEIVING INSTRUCTIONS 2.

Maintenance Manual MM Transfer Cases. MTC-4208X/XL/XP/XLEV, MTC-4210X/XL/XP/XLEV and MTC-4213X Series Revised 09-16

BASIC TROUBLE SHOOTING (PERFECTPASS FOR MECHANICAL ENGINES) How PerfectPass Works

Driver s Manual. Stored Energy Solutions Hydraulic Hybrid intellidrive System. Applies To: intellidrive 3000 intellidrive 1500

2010 MaxxForce 11 and 13L Diagnostics

Transcription:

W & Y Series Split-Shaft Chain Drive Transmission Operation and Maintenance Form No. F-1031 Section 2205.3 Issue Date 03/94 Rev. Date 06/24/13 Illustrations 1. Electric Shift Manual Override... 5 2. Pneumatic Shift Manual Override... 6 Table of Contents Safety Information... 1 Introduction... 2 General Description for Transmissions... 2 General Description for Accessories... 2 Shifting Instructions... 3 Manual Pump Shift... 3 Electric or Pneumatic Pump Shift... 4 Electric Shift Manual Override... 5 Pneumatic Shift Manual Override... 6 Maintenance... 8 Indicating Lights Operation... 8 Tachometer Readings... 8 Fluid Levels... 8 Shift Linkage... 8 Pump Shift Troubleshooting Guide... 9 Pump Transmission Shift Component Inpection... 12 W & Y Series Split Shaft Transmission Operation & Maint. Read through the safety information and operating instructions carefully before using your Waterous Fire Pump. Visit us at www.waterousco.com Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075 USA (651) 450-5000 Instructions subject to change without notice.

Safety Information Read through the safety information and operating instructions before using your Waterous Fire Pump. Death or serious personal injury might occur if proper operating procedures are not followed. The pump operator, as well as individuals connecting supply or discharge hoses to the apparatus must be familiar with these pump operating instructions as well as other operating instructions and manuals for the apparatus, water hydraulics and component limitation. Unexpected Truck Movement May result in serious personal injury or death Failure to properly shift in accordance to the operating instructions may result in unexpected truck movement which may result in serious personal injury or death. If the truck attempts to move, reduce engine speed to idle. Put truck in NEUTRAL and repeat shifting instructions. Page 1 of 13

Introduction Waterous Split Shaft Chain Drive Pump Transmissions are used with mid-ship mounted fire pumps. They transmit power from the truck's drive line to either the fire pump or to the drive axle of the truck. This instruction is divided into four sections: General Description for Transmissions General Description for Accessories Shifting Instructions Maintenance Instructions General Description for Transmissions The W and Y Series pump s are designed for use with Waterous Models CM, CS, CG and CX mid-ship mounted fire pumps and the RF-600 Self-Priming Pump. The s used with the CM, CMU, CS and CSU pumps have a separable splined connection to the pump impeller shaft allowing for easy removal of the for major service. Primary lubrication is provided through a splash system. A secondary chain lubrication system is also used, consisting of the spray bar, pump, hoses and strainer. The combined pressure and fluid splash system within the lubricates the sprockets, chain, bearings and other parts. The shaft driven fluid pump draws fluid from the sump through a strainer and then to a spray tube between the drive and driven sprockets, where the fluid is sprayed on the inside face of the chain just before the chain meshes with the driven sprocket. The strainer mounted in the sump of the pump filters the fluid to the pump. This strainer is removable for cleaning. An electronic tachometer sensor protrudes from the pump drive shaft housing at a 45 angle. Shaft rotational speed can be obtained with a frequency meter. NOTE: W Series equipped with a mechanical tachometer only. Y Series equipped with an electric tachometer only. The shift mechanism within the consists of a sliding internally-toothed collar which is always in engagement with an externally-toothed section of the drive shaft. A fork shifts the collar either to engage it with teeth on the drive sprocket hub (PUMP) or to engage it with the teeth on the coupling shaft (ROAD). When in PUMP position, the shift collar transmits power from the drive shaft through the drive sprocket and the chain to the driven sprocket. The coupling shaft remains stationary. When in ROAD position, the shift collar transmits power directly from the drive shaft through the coupling shaft to the truck propeller shaft and drive axle(s). In this position, the pump drive and driven sprockets remain stationary while the drive shaft rotates. Three shift indicator lights are furnished. Two are mounted in the cab and the other is mounted on the operators panel. These lights indicate to the operators that the shift has been completed into PUMP position and the truck is in pumping gear. General Description for Accessories The electric or pneumatic shift assembly permits fast, positive shifting without leaving the cab. A two-position control, mounted on the instrument panel in the cab activates the shift unit. Each accessory is equipped with a complete set of lights that indicate when the shift has been fully completed to PUMP and the truck is in pumping gear. NOTE: W Series equipped with a mechanical tachometer only. Y Series equipped with an electric tachometer only. Page 2 of 13

Two series of Allison automatic s are commonly used in fire trucks. Each series is available with the shift patterns controlled hydraulically or both electronically and hydraulically. This later type is commonly referred to as the ATEC. In each automatic, either the non-atec or the ATEC, certain sequences must occur in proper order after the pump shift control is moved to either PUMP or ROAD position. Split shaft pump s, automatic s and engines will vary in operation due to manufacturing tolerances, lubrication temperature, etc. This variance in each may or may not affect the ease of completing a full shift into either PUMP or ROAD. Operator training and experience in shifting procedures is a requirement to becoming skilled in a smooth, complete shift into either PUMP or ROAD. When the pump shift is activated, the operator may hear a noise associated with the movement of the shift unit. This does NOT mean that the shift has been completed. After the shift to pump operation is completed, the green PUMP ENGAGED and OK TO PUMP lights in the cab must be on before leaving the cab to operate the pump from the operators panel. DO NOT LEAVE THE CAB IF THE GREEN PUMP ENGAGED AND OK TO PUMP LIGHTS ARE NOT ON. Unexpected Truck Movement. May result in serious personal injury or death. Failure to properly shift in accordance to the operating instructions may result in unexpected truck movement which may result in serious personal injury or death. Shift to PUMP as follows: 1. Bring truck to complete stop. 2. Reduce engine to idle speed, put truck into NEUTRAL. 3. Set truck parking brake. 4. Move pump shift control to PUMP position. 5. Green PUMP ENGAGED light should be on. If green PUMP ENGAGED light is not on, momentarily shift truck into REVERSE while keeping pressure on the manual shift rod. Return to NEUTRAL. Green PUMP ENGAGED light should be on. 6. Lock pump shift control in PUMP position. 7. Shift truck into pumping gear (DRIVE). Shifting Instructions Manual Pump Shift Shifting truck into pumping gear (DRIVE) above engine idle speed may cause damage to the equipment. 8. Green OK TO PUMP light should be on. 9. Increase engine speed above idle and hold for a few seconds. Watch speedometer to make sure it shows some value of road speed. NOTE: Some fire trucks have a speedometer that will not show a value of road speed in a stationary position. Page 3 of 13 If the truck attempts to move, reduce engine speed to idle. Put truck in NEU TRAL and repeat shifting instructions. 10. After leaving truck cab, block wheels using wheel chocks. 11. To confirm that the pump is engaged: THROTTLE READY light on operator's panel is illuminated. Pump discharge pressure registers on gages. Other safety interlocks are activated. Shift to ROAD as follows: 1. With engine speed at idle, put truck in NEUTRAL. 2. When speedometer slows to zero, move pump shift control to ROAD position. 3. Lock pump shift control in ROAD position. 4. Engage truck (DRIVE) If you hear a loud grinding noise when you attempt to move the truck, the shift to ROAD has not been completed. Shift into NEUTRAL while keeping pressure on pump shift lever. If grinding is a common occurrence after Step 3 is performed, it may be prevented by shifting the truck into NEUTRAL, then to REVERSE, back to NEUTRAL and finally to DRIVE. 5. After shifting the truck to DRIVE, release the parking brake and move the vehicle forward to confirm a shift to ROAD has been completed.

Electric or Pneumatic Pump Shift Two series of Allison automatic s are commonly used in fire trucks. Each series is available with the shift patterns controlled hydraulically or both electronically and hydraulically. This later type is commonly referred to as the ATEC. In each automatic, either the non-atec or the ATEC, certain sequences must occur in proper order after the pump shift control is moved to either PUMP or ROAD position. Split shaft pump s, automatic s and engines will vary in operation due to manufacturing tolerances, lubrication temperature, etc. This variance in each may or may not affect the ease of completing a full shift into either PUMP or ROAD. Operator training and experience in shifting procedures is a requirement to becoming skilled in a smooth, complete shift into either PUMP or ROAD. When the pump shift is activated, the operator may hear a noise associated with the movement of the shift unit. This does NOT mean that the shift has been completed. After the shift to pump operation is completed, the green PUMP ENGAGED and OK TO PUMP lights in the cab must be on before leaving the cab to operate the pump from the operators panel. DO NOT LEAVE THE CAB IF THE GREEN PUMP ENGAGED AND OK TO PUMP LIGHTS ARE NOT ON. Some truck builders may install a manual override for the electric or pneumatic pump shift. The controls are normally installed from the pump to the operators panel. Unexpected Truck Movement. May result in serious personal injury or death. Failure to properly shift in accordance to the operating instructions may result in unexpected truck movement which may result in serious personal injury or death. Shift to PUMP as follows: 1. Bring truck to complete stop. 2. Reduce engine to idle speed, put truck into NEUTRAL. 3. Set truck parking brake. 4. Move pump shift control to PUMP position. NOTE: Green PUMP ENGAGED light may not illuminate. 5. Shift truck into pumping gear (DRIVE). 6. Green PUMP ENGAGED and OK TO PUMP lights should be on. If green PUMP ENGAGED and OK TO PUMP light are not on, momentarily shift truck from pumping gear (DRIVE) to NEUTRAL, then REVERSE, then NEUTRAL, then back into pumping gear (DRIVE). Lights should be on. If lights are not on, repeat procedure. 7. Increase engine speed above idle and hold for a few seconds. Watch speedometer to make sure it shows some value of road speed. NOTE: Some fire trucks have a speedometer that will not show a value of road speed in a stationary position. If the truck attempts to move, reduce engine speed to idle. Put truck in NEU TRAL and repeat shifting instructions. 8. After leaving truck cab, block wheels using wheel chocks. 9. To confirm that the pump is engaged: THROTTLE READY light on operator's panel is illuminated. Pump discharge pressure registers on gages. Other safety interlocks are activated. Shift to ROAD as follows: 1. With engine speed at idle, put truck in NEUTRAL. 2. When speedometer slows to zero, move pump shift control to ROAD position. 3. Engage truck (DRIVE). If you hear a loud grinding noise when you attempt to move the truck, the shift to ROAD has not been completed. Shift into NEUTRAL, wait for grinding noise to stop and re-engage truck. If grinding is a common occurrence after Step 3 is performed, it may be prevented by shifting the truck into NEUTRAL, then to REVERSE, back to NEU TRAL and finally to DRIVE. 4. After shifting the truck to DRIVE, release the parking brake and move the vehicle forward to confirm a shift to ROAD has been completed. Shifting truck into pumping gear (DRIVE) above engine idle speed may cause damage to the equipment. Page 4 of 13

Two series of Allison automatic s are commonly used in fire trucks. Each series is available with the shift patterns controlled hydraulically or both electronically and hydraulically. This later type is commonly referred to as the ATEC. In each automatic, either the non-atec or the ATEC, certain sequences must occur in proper order after the pump shift control is moved to either PUMP or ROAD position. Split shaft pump s, automatic s and engines will vary in operation due to manufacturing tolerances, lubrication temperature, etc. This variance in each may or may not affect the ease of completing a full shift into either PUMP or ROAD. Operator training and experience in shifting procedures is a requirement to becoming skilled in a smooth, complete shift into either PUMP or ROAD. When the pump shift is activated, the operator may hear a noise associated with the movement of the shift unit. This does NOT mean that the shift has been completed. After the shift to pump operation is completed, the green PUMP ENGAGED and OK TO PUMP lights in the cab must be on before leaving the cab to operate the pump from the operators panel. DO NOT LEAVE THE CAB IF THE GREEN PUMP ENGAGED AND OK TO PUMP LIGHTS ARE NOT ON. If the vehicle builder has provided a means to manually override the electric pump shift, the override control will be located at the operators panel or in the cab. The override control will consist of a rod to the panel or a cable or rod mechanism to the inside of the cab. The rod or cable will be attached to the shift arm on the pump. NOTE: This instruction is written based on an override control rod directed to the operators panel from the short arm of the lever on the pump. Other rod or cable arrangements may require reversal of stated action to accomplish the desired shift. If the pump is equipped with an override, shifting manually is done as follows: It is recommended that this procedure be performed using two people; one person in the cab and one at the override control position. Unexpected Truck Movement. May result in serious personal injury or death. Failure to properly shift in accordance to the operating instructions may result in unexpected truck movement which may result in serious personal injury or death. Electric Shift Manual Override Shift to PUMP as follows: 1. Bring truck to complete stop. 2. Reduce engine to idle speed, put truck in NEUTRAL. 3. Set truck parking brake. 4. Pull the shift override control rod out at the operators position to disengage the electric shift unit from the pump shift arm. See Figure 1. Figure 1. Electric Shift Manual Override IL1676 5. Push manual shift control rod in for PUMP position. 6. Move in-cab pump shift control into PUMP position. 7. Green PUMP ENGAGED light should be on. If green PUMP ENGAGED light is not on, momentarily shift truck into REVERSE while keeping pressure on the manual shift rod. Return to NEUTRAL. Green PUMP ENGAGED light should be on. 8. Shift truck into pumping gear (DRIVE). Shifting truck into pumping gear (DRIVE) above engine idle speed may cause damage to the equipment. 9. Green OK TO PUMP light should be on. 10. Increase engine speed above idle and hold for a few seconds. Watch speedometer to make sure it shows some value of road speed. NOTE: Some fire trucks have a speedometer that will not show a value of road speed in a stationary position. Page 5 of 13

If the truck attempts to move, reduce engine speed to idle. Put truck in NEU TRAL and repeat shifting instructions. 11. After leaving truck cab, block wheels using wheel chocks. 12. To confirm that the pump is engaged: THROTTLE READY light on operator's panel is illuminated. Pump discharge pressure registers on gages. Other safety interlocks are activated. Shift to ROAD as follows: 1. With engine at idle speed, put truck in NEUTRAL. 2. When speedometer drops to zero, pull manual shift rod out for ROAD position. Push the override control rod in to engage shift unit. 3. Move in-cab pump shift control into ROAD position. 4. Engage truck (DRIVE). If you hear a loud grinding noise when you attempt to move the truck, the shift to ROAD has not been completed. Shift into NEUTRAL, wait for grinding noise to stop and re-engage truck, while keeping pressure on the manual shift control rod. 5. After shifting the truck to DRIVE, release the parking brake and move the vehicle forward to confirm a shift to ROAD has been completed. Pneumatic Shift Manual Override Two series of Allison automatic s are commonly used in fire trucks. Each series is available with the shift patterns controlled hydraulically or both electronically and hydraulically. This later type is commonly referred to as the ATEC. In each automatic, either the non-atec or the ATEC, certain sequences must occur in proper order after the pump shift control is moved to either PUMP or ROAD position. Split shaft pump s, automatic s and engines will vary in operation due to manufacturing tolerances, lubrication temperature, etc. This variance in each may or may not affect the ease of completing a full shift into either PUMP or ROAD. Operator training and experience in shifting procedures is a requirement to becoming skilled in a smooth, complete shift into either PUMP or ROAD. When the pump shift is activated, the operator may hear a noise associated with the movement of the shift unit. This does NOT mean that the shift has been completed. After the shift to pump operation is completed, the green PUMP ENGAGED and OK TO PUMP lights in the cab must be on before leaving the cab to operate the pump from the operators panel. DO NOT LEAVE THE CAB IF THE GREEN PUMP ENGAGED AND OK TO PUMP LIGHTS ARE NOT ON. If the vehicle builder has provided a means to manually override the pneumatic pump shift, the override control will be located at the operators panel or in the cab. The override control will consist of a rod to the panel or a cable or rod mechanism to the inside of the cab. The rod or cable will be attached to the shift arm on the pump. NOTE: This instruction is written based on an override control rod directed to the operators panel from the short arm of the lever on the pump. Other rod or cable arrangements may require reversal of stated action to accomplish the desired shift. Figure 2. Pneumatic Shift Manual Override Rod or cable to cab Rod to side of truck IL1011 If the pump is equipped with an override, shifting manually is done as follows: It is recommended that this procedure be performed using two people; one person in the cab and one at the override control position. Unexpected Truck Movement. May result in serious personal injury or death. Failure to properly shift in accordance to the operating instructions may result in unexpected truck movement which may result in serious personal injury or death. Page 6 of 13

Shift to PUMP as follows: 1. Bring truck to complete stop. 2. Reduce engine to idle speed, put truck in NEUTRAL. 3. Set truck parking brake. 4. Move in-cab pump shift control into the CENTER position. 5. Push manual shift control rod in for PUMP position. 6. Move the in-cab pump shift control into the PUMP position. 7. Green PUMP ENGAGED light should be on. If green PUMP ENGAGED light is not on, momentarily shift truck into REVERSE while keeping pressure on the manual shift rod. Return to NEUTRAL. Green PUMP ENGAGED light should be on. 8. Shift truck into pumping gear (DRIVE). Shift to ROAD as follows: 1. With engine at idle speed, put truck in NEUTRAL. 2. When speedometer drops to zero, move in-cab pump shift control into the CENTER position. 3. Pull manual shift rod out for ROAD position. 4. Move the in-cab pump shift control into the ROAD position. 5. Engage truck (DRIVE). If you hear a loud grinding noise when you attempt to move the truck, the shift to ROAD has not been completed. Shift into NEUTRAL, wait for grinding noise to stop and re-engage truck, while keeping pressure on the manual shift control rod. 6. After shifting the truck to DRIVE, release the parking brake and move the vehicle forward to confirm a shift to ROAD has been completed. Shifting truck into pumping gear (DRIVE) above engine idle speed may cause damage to the equipment. 9. Green OK TO PUMP light should be on. 10. Increase engine speed above idle and hold for a few seconds. Watch speedometer to make sure it shows some value of road speed. NOTE: Some fire trucks have a speedometer that will not show a value of road speed in a stationary position. If the truck attempts to move, reduce engine speed to idle. Put truck in NEU TRAL and repeat shifting instructions. 11. After leaving truck cab, block wheels using wheel chocks. 12. To confirm that the pump is engaged: THROTTLE READY light on operator's panel is illuminated. Pump discharge pressure registers on gages. Other safety interlocks are activated. Page 7 of 13

Indicating Lights Operation Check the operation of the pump shift indicating lights at least weekly as follows: NOTE: Block wheels with wheel chocks before beginning. 1. With the pump in the ROAD position, truck in NEUTRAL and the parking brake engaged, ensure that the PUMP ENGAGED and OK TO PUMP lights in the cab are off. 2. Shift to PUMP following the shifting instructions section of this document. a. Ensure that the green PUMP ENGAGED and OK TO PUMP lights in the cab are on. b. Ensure that the green THROTTLE READY light on the operator's panel is on. 3. Apply the service (foot) brake and release the parking brake. a. Ensure that the green OK TO PUMP light in the cab is off. b. Ensure that the green THROTTLE READY light on the operator's panel is off. 4. Engage the parking brake and shift truck to NEUTRAL. a. Ensure that the green OK TO PUMP light in the cab is off (automatic truck only). 5. Shift to ROAD following the shifting instructions section of this document. a. Ensure that the green PUMP ENGAGED and OK TO PUMP lights in the cab are off. b. Ensure that the green THROTTLE READY light on the operator's panel is off. Tachometer Readings Mechanical Tachometer: Speed of drive tachometer gear is 1/2 of input shaft speed. Electric Tachometer: To verify input shaft speed, take a frequency reading from the tachometer sensor. Multiply frequency reading (Hz) by 1.5 for shaft speed. The impeller shaft speed can be calculated by multiplying the input shaft speed by the ratio of the pump. Maintenance Fluid Levels 1. Check fluid level monthly by removing fluid level plug at rear of case. The fluid should be level with bottom of hole. A sight plug is also provided for this purpose, and the fluid level should be visible thru this plug. If fluid level is low, locate source of leak and repair. If fluid level is high, loosen drain plug until fluid drops to proper level. If excessive water drains out, change fluid and determine source of water leakage and repair. NOTE: Fluid temperature should not exceed 250 for an extended period of time or premature seal wear and damage may occur. Fluid can be added thru the fluid level hole or by removing the breather and adding fluid thru this opening. Any type of automatic fluid (ATF) can be used. 2. Transmission fluid pump operation should be checked monthly. If a fluid pump pressure gauge has been installed in the system, it should show a positive pressure while in the PUMP position. NOTE: Fluid pressure will vary depending on engine speed and lubricant temperature. 3. Change fluid twice per year or after each 100 hours of operation, whichever comes first. Clean the fluid sump strainer, breather and magnetic drain plug thoroughly whenever the fluid is changed. The strainer can easily be removed by disconnecting the hose at the strainer and unscrewing the strainer from the case. Replace the strainer if it cannot be cleaned or is damaged. Amount required if system is drained and refilled Y Series 13 qts. (approx.) W Series 6 qts. (approx.) Shift Linkage Periodically check all shift linkage for freedom of movement and clean as necessary. Page 8 of 13

Pump Shift Troubleshooting Guide It is important to know what to do if you experience shifting problems with your pump. This troubleshooting guide will help you diagnose, isolate and correct problems as they are encountered. For problems not covered in this guide, or for additional technical assistance, please contact the Waterous Service Department. Problem Is the chassis in DRIVE (automatic) or in its pump gear (Manual)? Pneumatic Shift Possible Cause Electric Shift Recommended Action Pump won't engage Pump shift control is in the PUMP position and: 1. No lights or Red light stays on or flashed (units built prior to 1991). or 2. PUMP ENGAGED light does not come on (units built 1991 or newer). No Butt-tooth condition Butt-tooth condition Yes Malfunctioning shift indicating switch or switch out of adjustment Manual override linkage binding Excessive driveline torque Low air pressure to pneumatic shift unit (80 psi min.) Leaking pneumatic shift unit. Malfunctioning air control valve Malfunctioning shift indicating switch or switch out of adjustment Manual override linkage binding Excessive driveline torque No power to shift unit. Failed shift motor - check current draw, should be 20A at startup and 10A through the cycle. Failed shift unit - unit has power and draws correct amperage but will not activate. Place the chassis in Drive (automatic) or in its pumping gear (manual). Replace or adjust the shift indicating switch or bracket. Repair or replace to eliminate binding. Shift the chassis into REVERSE momentarily, then NEUTRAL, then DRIVE. Consider reducing engine idle speed. It may be necessary to contact the chassis manufacturer for assistance. Allow air pressure to build in the system, repair any leaks in the system. Repair or replace pneumatic shift unit. Repair or replace air control valve. Repair as needed to restore power supply. Replace the shift motor. Repair or replace the electric shift unit. Page 9 of 13

Problem Pump will not engage and there is a grinding noise emanating from the pump. Pump shift control is in the PUMP position and: 1. The chassis is in DRIVE (automatic) or in its pumping gear (manual). or 2. The chassis is in NEUTRAL. Chassis engine stalls after placing the pump shift control in PUMP and placing the chassis in DRIVE (automatic) or in its pumping gear (manual). Is the PUMP ENGAGED light on? No Yes No Pneumatic Shift Manual override linkage binding. Excessive driveline torque. Low or no air pressure to pneumatic shift unit (80 psi min.) Damage to internal pump shifting components. Shift indicating switch is out of adjustment or its bracket is damaged. Damage to internal pump shifting components. Pump has not shifted out of ROAD due to excessive driveline torque. Damage to internal pump shifting components. Possible Cause Electric Shift Manual override linkage binding. Excessive driveline torque. Weak shift unit or non-waterous supplied shift unit. Damage to internal pump shifting components. Malfunctioning shift indicating switch or switch out of adjustment. Damage to internal pump shifting components. Pump has not shifted out of ROAD due to excessive driveline torque. Damage to internal pump shifting components. Yes Seized fire pump. Seized fire pump. Recommended Action Repair or replace to eliminate binding. Shift the chassis into REVERSE momentarily, then NEUTRAL, then DRIVE. Consider reducing engine idle speed. It may be necessary to contact the chassis manufacturer for assistance. Allow air pressure to build in the system, repair any leaks in the system. Replace shift unit with a high-torque shift unit provided by Waterous. See pump inspection instructions. Adjust the shift indicating switch or replace the bracket. See pump inspection instructions. Shift the chassis into REVERSE momentarily, then NEUTRAL, then DRIVE. Consider reducing engine idle speed. It may be necessary to contact the chassis manufacturer for assistance. See pump inspection instructions. Repair fire pump as necessary. Page 10 of 13

Problem Is the chassis in DRIVE (automatic) or in its pump gear (Manual)? Pneumatic Shift Possible Cause Electric Shift Recommended Action No Chassis not in the proper gear. Chassis not in the proper gear. Place the chassis in DRIVE (automatic) or in its pumping gear (manual). PUMP ENGAGED light is on but OK TO PUMP light will not illuminate. (Units built 1991 and later) Yes Parking brake is not applied. Problem with high range lockup or safety interlock systems. Parking brake is not applied. Problem with high range lockup or safety interlock systems. Apply the parking brake. Contact the apparatus manufacturer or consider alternative wiring for high range lockup. Problem with chassis or electronic control unit. Problem with chassis or electronic control unit. Contact the chassis manufacturer for assistance. Problem Is the Pump shift arm in contact with the shift indicating switch? Pneumatic Shift Possible Cause Electric Shift Recommended Action Pump shift control is in the ROAD position, but the PUMP ENGAGED and/or OK TO PUMP lights stay on. Note: Chassis engine may stall if the chassis is placed in DRIVE (automatic) or in its pumping gear (manual). No Yes Shift indicating switch stuck closed. Locking arm assembly is installed backwards inside pump (the shift arm should move away from the shift indicating switch when shifting to pump). Shift indicating switch stuck closed. Locking arm assembly is installed backwards inside pump (the shift arm should move away from the shift indicating switch when shifting to pump). Replace the shift indicating switch. Remove locking arm assembly and re-install correctly. Page 11 of 13

Problem Pump shift control is in the ROAD position and grinding sounds are heard emanating from the pump. Manual pump shift override control cannot be moved by hand (electric or pneumatic shift functions properly). Pneumatic Shift Chassis is in gear when shifting pump. Butt-tooth condition - chassis is in REVERSE. Excessive driveline torque and/or rotation. Damage to pump shifting components. Air pressure present on pneumatic shift piston. Binding or malfunctioning manual shift linkage. Possible Cause Electric Shift Chassis is in gear when shifting pump. Butt-tooth condition - chassis is in REVERSE. Excessive driveline torque and/or rotation. Damage to pump shifting components. Electric shift still engaged with shift arm. Binding or malfunctioning manual shift linkage. Recommended Action Place the chassis in NEUTRAL before shifting pump. Place the chassis in DRIVE after shifting pump to ROAD. Ensure the driveline is not rotating before shifting to ROAD. Consider reducing engine idle speed. It may be necessary to contact the chassis manufacturer for assistance. See pump inspection instructions. Place the shift air control valve in the center position. (Note: There is no center position on units built prior to 1994). Operate the electric shift to disengage control. Repair or replace to eliminate linkage binding. The chassis engine stalls when the chassis is placed in DRIVE (automatic) after moving the pump shift control to the ROAD position. Shift indicating switch stuck closed. Problem with chassis or electronic control unit. Shift indicating switch stuck closed. Problem with chassis or electronic control unit. Replace the shift indicating switch. Contact chassis manufacturer for assistance. Pump Transmission Shift Component Inspection The following procedures should be followed when a problem with the pump shift components is suspected: 1. Perform a shift force test on the pump. a. Place the chassis in NEUTRAL and shut off the engine. b. Set the apparatus parking brake. c. Remove any manual override linkage from the pump shift arm. d. Remove the pneumatic or electric shift unit (if so equipped) from the pump. e. Manually align the shift teeth by actuating the pump shift arm and rotating the drive shaft until the shift collar is engaged in the PUMP position. f. Pull on the long side of the shift arm to shift the pump between ROAD and PUMP using a pull scale to measure the force required in pounds. The force required to shift the pump should not exceed 18 pounds. Page 12 of 13

2. Drain the lubricant from the pump and examine it for metal particles appearing in quantity and/or size which may indicate excessive wear to internal components. Also check the magnetic drain plug and the sump screen on the lube pump intake line (if so equipped) for debris. If there is little or no debris refill with clean lubricant and retest. If the problem persists or if large quantities or sizes of debris are found proceed to step 3. 3. Remove the lower section of the pump according to the pump overhaul instructions. 4. Inspect the pump shift components, including: a. Check for damage to the shift fork and the shift shoes. b. Check for damage to the shift shaft, locking arm assembly and sector gear. c. Check for damage to the engaging teeth on the drive sprocket, coupling shaft and shift collar. Note: it will be necessary to manually actuate the shift arm to inspect all of the teeth. Some binding may normally occur when actuating the shift arm with the lower case section removed). Minor burrs found on the teeth of the shift collar, drive sprocket, or coupling shaft may be filed clean. If excessive damage is found the component(s) should be replaced. d. Check to make sure that all bearings turn freely. 5. Contact Waterous to order any replacement parts or for further assistance. Page 13 of 13