PERFORMANCE SOLUTIONS SINCE 1982
Customers Praise These Cost-Effective Results: METALON is a hydrocarbon complex specifically formulated to help reduce friction and wear of ferrous and non-ferrous metals. The Cost-Effective results are: INCREASED PERFORMANCE LONGER EQUIPMENT LIFE ENERGY SAVINGS REDUCED SYSTEM TEMPERATURES REDUCED COSTLY MAINTENANCE & DOWNTIME KEEPS WEAR IN CHECK
Product Line METALON M METALON C2 METALON HI-TECH EP 1.5 GREASE METALON SPRAY PENETRANT MEGALENE MEGASEL For Crankcases & Mechanical Equipment A Universal Formula The Superior Lubricant Anti-Wear Friction Fighter Gas System Treatment Diesel Fuel System Treatment ULTIMATE MECHANICAL PROTECTION
METALON M Crankcases and Mechanical Equipment METALON M contains powerful solvents and detergents to rid the lubrication system of sludge and carbon deposits in filtered lubricating systems. It is applied at a 5% ratio (min.); 100 ml for every two litres of lubricants (8 oz. to 5 U.S. quarts). TYPICAL USES Crankcases, Mechanical Gear Boxes, Differentials, Transfer Boxes, Sliding Mechanisms, Cutting, Threading and Machining Oils, Bearings, Filtered Compressor Pumps, Bushings and much more. Packaging: 12 x 250 ml, 12x1L, 4L, 4x4L, 20L, 205L (Some applications may require a higher ratio of METALON M to realize optimum benefits, which is dictated by experience.)
METALON C2 A Universal Formula METALON C2 can replace METALON M wherever there is no need for solvents or detergents in the lubrication system. When used in non-filtered lube systems, METALON C2 will not disturb old sludge and contamination that may exist. This factor makes it suitable for oil injected systems and hydraulic systems that do not require a Zinc component in the fluid. METALON C2 will substantially improve the performance of AUTOMATIC TRANSMISSIONS. It is compatible with GM DEXRON III and FORD TYPE fluids used in most transmissions and some hydraulic systems. METALON C2 helps to reduce extreme transmission temperatures; the enemy of tranny fluids. Excessive heat accelerates fluid decomposition. METALON C2 does not adversely affect the "design friction" required in the fibre-metal clutch driving mechanisms or tranny seals. METALON C2 is effective in semi-automatic transmissions and transaxle drives common in many front wheel drive vehicles. O METALON C2 can reduce hydraulic operating temperatures by as much as 70 F. This heat reduction will help prevent premature fluid degradation and help to preserve the integrity of the hydraulic seals, hoses and couplings. TYPICAL USES METALON C2, a non-solvent, multi-purpose formula, can be blended with gas-oil mixtures for Two-Stroke Power Sources, such as: Chain Saws, Ground Keeping & Golf Course Maintenance Equipment, Logging Machinery, Outboard Motors, Snow Machines, Jet Skis, Model Aircraft Engines, and the like. METALON C2 blends with oils and fluids for Hydraulic Systems, Hydraulic Cranes, Self-Loaders, Hydraulic Power Generators, Compressors, Metal Machining and Forming, etc. METALON C2 is applied at a ratio of 5% to the system fluid. For Automatic Transmissions, follow the directions found in the vehicle owner's manual. For gas-oil mixtures, blend initially at a ratio of 1 ounce of METALON C2 per blended gallon for the first gallon burned. Thereafter, reduce to 1/2 ounce per gallon. Packaging: 12x 250 ml, 4L, 4x4L, 20L, 205L
METALON HIGH-TECH 1.5 GREASE The Superior Lubricant METALON HI-TECH 1.5 GREASES is a superior multi-use high performance lubricant. Its unique overbased calcium sulfonate foundation coupled with the exceptional properties of METALON EP provides the ultimate New Generation lubricating medium that is unmatched in the industry. METALON HI-TECH EP 1.5 GREASE is an "indispensable" maintenance "tool". Its Cost-Effective Performance is further enhanced by its ability to reduce inventories and misapplication problems. Its NLGI 1.5 penetration rating eliminates the need to stock a grade #1 and grade #2. This 1.5 grade provides excellent pumpability and dispensing properties. METALON imparts operational and residual Anti-Wear Protection under light, medium and extra-heavy loads. METALON protects against Dry Drag, while reducing Friction, Heat, Wear, Maintenance Downtime and Energy Costs. METALON HI-TECH EP 1.5 GREASE guards against rust, corrosion, oxidation, water washout and offers O O O excellent thermal stability through temperatures ranging from -40 C/F to 300 C (570 F) intermittently, O O sustainable to 250 C/482 F) and IT'S REVERSIBLE! (Returns to its original buttery state when cooled). An added bonus: METALON HI-TECH EP 1.5 GREASE blends favourably with lithium and many other greases, permitting easy replacement of lesser quality greases. Note 1: METALON HI-TECH EP 1.5 GREASE has been assigned a NATO NUMBER, which is: 9150-21-905-7275, registered with the Government of Canada; Supply and Services. Note 2: METALON HI-TECH EP 1.5 GREASE meets or exceeds all NLGI Specifications as it relates to heavy duty wheel bearing lubrication, specifically those specifications designed under the code identifier: "G/C- L/B" ratings. TYPICAL USES Industrial, Farm Production and Construction Machinery, Automobile, Truck and Military Vehicles & Equipment, Mining and Marine Equipment, Top Drive Actuators, Bearings, Gears, Stuffing Boxes, Automatic Lubricating Systems, Oven Conveyors, Dry Kilns, Motors & Equipment, High and Low Speed Mechanisms, Fifth Wheels and many other grease applications. Packaging: 10x400g, 60x400g, 20kg, 55kg, 180kg
METALON SPRAY PENETRANT Anti-Wear Friction Fighter METALON SPRAY PENETRANT is a hydro-carbon complex specifically formulated to help reduce wear and friction of ferrous & non-ferrous metals. METALON SPRAY PENETRANT unites chemically with the metal component molecules, forming a microscopic, monomolecular, wear-resistant shield. This exclusive lubricating formula combines the extraordinary features of METALON with other components that meet Military Specification requirements. METALON SPRAY PENETRANT will help to increase production and service life of equipment. Reduce down-time and crucial wasteful maintenance expenditures. METALON SPRAY PENETRANT is Non-Flammable. This provides an important margin of safety where potential hazards exist. Its high dielectric strength permits effective cleaning and retardation of electrical corrosion. The penetrating and "creep" properties help free, lubricate and protect rusted and seized components. Moisture is driven out. A little goes a long way which makes METALON SPRAY PENETRANT very cost-effective. Aerosolized for convenience, METALON SPRAY PENETRANT uses CARBON DIOXIDE (CO 2) as a propellant, which is classed as "OZONE SAFE". TYPICAL USES Tools, Locks, Valves, Guns, Mechanical Linkages, Rusted Bolts, Nuts and Parts, Air Tools, Fishing Gear, Electric Motors, Jack Hammers, Sliding Mechanisms, Bicycles, Hinges, Chainfalls, Chain Saws, Nailing and Fastening Tools, Machine Threads, Tool & Dies, Drilling, Tapping, Metal Drawing and Forming, Broaching, Sawing, Milling Operations, Carburetor Linkages, Motorbikes, etc. Read and follow directions on the label before using METALON SPRAY PENETRANT Packaging: 12x400g
MEGALENE Gas System Treatment MEGALENE GAS SYSTEM TREATMENT, now with METALON is a New and Improved hydrocarbon complex that incorporates components which are ashless, non-phosphorus, and perform as multi-functioned detergents. These proprietary components exceed the Military Specifications MIL-I-25017B and MIL-I-25017C, providing excellent rust protection in both leaded and unleaded gasolines. When used continuously as directed, MEGALENE helps to: Lubricate upper Cylinder Components, Maintain Optimum Carburetor & Fuel Injector Performance, Neutralize Acids, Enhance Combustion, Clean PVC Systems, Prevent Fuel System Icing, Clean Varnish & Gum Residues, Eliminate Carbon Deposits, Prevent Engine Run-On Improve Economy, Arrest Rust & Corrosion, Free Sticky Valves, Reduce Harmful, Toxic Exhaust Emissions that pollute the environment and much more. TYPICAL USES MEGALENE GAS SYSTEM TREATMENT can be added to all gasolines used in internal combustion engines. It is compatible with Catalytic converters. This highly concentrated formula is very "Cost-effective". For the first 200L of gasoline, add 20mL MEGALENE to every 40L (For rapid results, slowly pour 50mL directly into the carburetor with the engine at fast idle.) Regularly add 10mL for every 40L. Caution: MEGELENE is Flammable. Keep away from open flame or spark. Contains petroleum distillates. If swallowed, DO NOT induce vomiting. Call physician immediately. Packaging: 12x250mL, 12x1L, 4L, 4x4L, 20L, 205L
MEGASEL Diesel Fuel System Treatment MEGASEL DIESEL FUEL SYSTEM TREATMENT, now with METALON, is a New and Improved hydrocarbon complex that is used to maintain distillate fuel in a sludge-free stabilized condition. MEGASEL arrests many of the problems related to storage, transportation and combustion of fuels used in diesel turbines, fuel-oil burning boilers, steam generators and internal combustion engines. Diesel fuel stability is adversely affected by the widespread practice of blending fuels from different sources. Fuel degradation is accelerated causing sludge and bacteria formation and reduced combustibility. Sticking fuel injectors, contaminated fuel lines, filters and pumps waste costly fuel, reduce operating efficiency and increase maintenance costs. The problems of corrosion, rust, acid formation and water damage are also prevalent in diesel fuel systems. MEGASEL DIESEL FUEL SYSTEM TREATMENT incorporates the quality multi-functional components required to efficiently arrest the inherent problems noted above. In addition, METALON bonds, chemically with the metal component molecules, forming a microscopic, monomolecular frictionreducing, wear resistant shield that will not drain off. The burnishing action of METALON produces a more precise metal-to-metal fit that increases component life. The efficiency of the critical fuel injectors is substantially enhanced, maintaining consistent spray patterns and accurate fuel metering. Upper cylinders are lubricated. Cold weather "gelling" is also retarded. Water droplets - a great potential hazard when locked in suspension, are emulsified (broken up) and allowed to pass through the system efficiently. MEGASEL is virtually ashless (contains no inorganics or metallics), is compatible with most hydrocarbon fuel stocks and is non-extractable. MEGASEL dissolves carbon deposits, reduces black smoke and other emissions considered harmful to the environment. MEGASEL components comply with the EPA regulations listed in the Additives Manufacturer notifications, form EPA (DUR) 365. When used continuously as directed, MEGASEL helps to: Clean & Protect Injectors, Reduce Exhaust Emissions, Prevent Sludge Formation, Prevent Fuel System Icing, Lubricate Upper Cylinders, Free Sticky Valves, Eliminate Carbon Deposits, Neutralize Acids, Reduce Blow-by Oil Dilution, Improve Fuel Combustion, Retard Bacterial Growth, Arrest System Rust/Corrosion, and much more. MEGASEL DIESEL FUEL SYSTEM TREATMENT should be added before filling the tank to aid blending, especially if there is no agitation, Initial Treatment: Add 20mL of MEGASEL to every 40 Litres of No.1 and No. 2 diesel fuel to clean and prime the system. Regular Treatment: Add 10mL to every 40 litres. For No.3 to No.6 fuels, double or triple treatment, respectively. CAUTION: MEGASEL is Flammable. Keep away from open flame of spark. Contains petroleum distillates. If swallowed, DO NOT induce vomiting, Call physician immediately. Packaging: 12x250mL, 12x1L, 4L, 4x4L, 20L 205L
PERFORMANCE SOLUTIONS SINCE 1982 Asia. Canada. Russia. Switzerland. USA Jamaica. Philippines. Poland. Trinidad METALON, LLC. 5205 Blue Stem Court, Raleigh NC 27606-9373 919 834-9444 Fax 866 448-1421 usa@metalonproducts.com METALON PRODUCTS A division of Professional Products of Canada Inc. 2624 Royal Windsor Drive, Unit 7 Mississauga, Ontario L5J 1K7 Canada 1-877-LUBRIC8 (582-7428) Phone 905 855-4826 Fax 905 855-9900 canada@metalonproducts.com TM