January 00 Sheet 1187 Motor Starters & Contactors Low Voltage Enclosures General Individual Enclosed, ac Full Voltage.7- Combination Starters Maximum 00 hp, Volts Application Size 1, NEMA 1, Enclosed Magnetic combination starters are designed for across-the-line control of squirrel cage motors or as primary control for wound rotor motors. In addition, they provide a disconnect means and short-circuit protection. They can be furnished for non-reversing or reversing applications. Starter Types Non-reversing ECN16: Freedom NEMA Non-Fusible Switch. ECN16: Freedom NEMA Fusible Switch. ECN: Freedom NEMA Circuit Breaker (HMCP). ECT16: IT. NEMA Non-Fusible Switch. ECT16: IT. NEMA Fusible Switch. ECT: IT. NEMA Circuit Breaker (HMCP). Reversing ECN17: Non-Fusible Switch. ECN17: Fusible Switch. ECN: Circuit Breaker (HMCP). ECT17: IT. NEMA Non-Fusible Switch. ECT17: IT. NEMA Fusible Switch. ECT: IT. NEMA Circuit Breaker (HMCP). Enclosures Type 1: General Purpose. Type R: Rainproof. Type 4: Watertight, Painted Steel. Type 4X: Watertight, Stainless Steel. Type 1: Dust-tight Industrial Use. Type 7/9: Explosion Proof. Ratings See Section.. Typical Freedom across-the-line combination starters for motors up to 900 hp, volts are Cutler-Hammer NEMA Type ECN16 (fusible disconnect) or ECN (motor circuit protector HMCP). Reversing combination starters for motors up to 900 hp, volts are Cutler-Hammer Freedom Series Type ECN17 (fusible disconnect) or ECN (motor circuit protector HMCP). All starters are built in accordance with the latest NEMA standards and conform to the National Electrical Code in addition to being UL listed. Freedom overload relays are ambient compensated bimetallic type with interchangeable heaters, calibrated for 1.0 and 1.1 service factor motors. Electrically isolated NO and NC contacts are provided on the relay. Visual trip indication is standard. A test trip feature is provided for ease of troubleshooting and is conveniently operable without removing components or the motor starter. IT. across-the-line combination starters for motors up to 900 hp, volts are Cutler-Hammer NEMA Type ECT16 (fusible disconnect) or ECT (motor circuit protector HMCP). Reversing combination starters for motors up to 900 hp, volts are Cutler-Hammer Freedom Series Type ECT17 (fusible disconnect) or ECT (motor circuit protector HMCP). IT. solid-state overload relays come with a.:1 adjustment range. They also have phase loss protection, an alarm contact, selectable manual or automatic reset, test feature and an alarm without trip configuration. For Freedom starters, control circuit transformers, where specified, are encapsulated. Primary and secondary fusing is provided. Unless otherwise specified, the secondary will be Vac. For IT. starters, control circuits are Vdc. Pilot devices, where specified, will be oiltight and mounted in the flange. Pilot lights of the transformer type are available for longer lamp life. Pilot device nameplates are engraved phenolic or aluminum. The operating mechanism will be mounted on the flange and have positive, non-teasing ON/OFF action. The handle is color coded: red for ON and black for OFF. The operating handle has a means to lock the handle in the OFF position with a minimum of three standard padlocks having 1/4-inch (6.4 mm) diameter shackles. Where specified, a disconnect switch with double break, rotary blades and quick make/quick break action can be provided. A line shield with test probe holes for inspection will be provided. The shield is removable. The switch will have readily visible blades in the open (OFF) position. The fusible disconnect switch (through 0 amperes) will have built-in fuse pullers to make it easier to remove fuses. Where specified, an adjustable instantaneous trip, magnetic-only circuit breaker will be provided. A manual push-to-trip button is provided to exercise the trip unit. Fusible disconnect switches are UL listed for 0,000 amperes when Class R fuses are used. Combination starters with adjustable instantaneous trip, magnetic-only circuit breakers can be UL listed for up to 0,000 amperes through 480 volts. 1 L1 L L Fusible or Non-Fusible Disconnect Switch or Circuit Breaker A1 A 98 97 96 T1 T T 9 T1 T T 0 1 6 7 8 9 1 4 6 8 Motor Figure.7-1. Wiring Diagram CA0801E
January 00 Sheet 1117 Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line General.-1 Freedom IEC AE17KNS0AFE IEC Size K, 0 hp/ V Product NEMA AN16DN0AB NEMA Size 1 The Freedom Series starters and contactors listed in this catalog feature a compact, space-saving design, using state-of-the-art technology and the latest in high strength, impact and temperature-resistant insulating materials. Starters and contactors are available in two rating/configuration styles NEMA (National Electrical Manufacturers Association) and IEC (International Electrotechnical Commission). The NEMA devices are sized based on traditional NEMA classifications and the IEC devices on international ratings. Internationally rated starters and contactors, as compared to NEMA devices, generally are physically downsized to provide higher ratings in a smaller package. However, electrical load/life ratings are correspondingly reduced. Careful consideration should be given to the selection of the proper device for a specific application. Parameters, such as type of load, severity of duty, electrical load/life cycles required, etc., must be evaluated before choosing either the IEC or NEMA designs. Since the IEC devices are typically smaller than the equivalent NEMA device, there is a cost advantage over the NEMA starters and contactors. Application The Freedom to Choose the Right Product for the Application Eaton has been supplying quality industrial control products for more than 0 years the Freedom Series of Contactors and Starters continue in this tradition. They offer something no other electrical control line in the world can the Freedom to choose contactors and starters designed to either NEMA or IEC standards from one family. There are many difficult choices to be made today in matching electrical control to a specific application, but the Cutler-Hammer Freedom Series makes it easy. Features Freedom Family A single family of contactors and starters suitable for application in both the IEC and NEMA markets. Two lines, One family the best of both worlds. Adjustable Bimetallic Ambient Compensated Overload relays with interchangeable heater packs available in three basic sizes, covering applications up to 900 hp reducing the number of different contactor/overload relay combinations that have to be stocked. Fixed heater overloads are optional. A full line of snap-on accessories common to both IEC and NEMA devices top and side mounted auxiliary contacts, solid-state and pneumatic timers, etc. Straight-through wiring line lugs at top, load lugs at bottom. Horizontal or vertical mounting on upright panel for application freedom. Screw type power terminals have captive, backed-out self-lifting pressure plates with ± screws reduced wiring time. Accessible terminals for easy wiring. Optional fingerproof shields available to prevent electrical shock. Top located coil terminals convenient and readily accessible. 4 mm contactor magnet coils have three terminals, permitting either top or diagonal wiring easy to replace European or U.S. style starters or contactors without changing wiring layout. Encapsulated dual voltage/frequency magnet coils permanently marked with voltage, frequency and part number. NEMA Sizes 00 0 have non-encapsulated coils as standard. Designed to meet or exceed NEMA, UL, CSA, IEC, VDE, BS and other international standards and listings. Freedom NEMA Freedom NEMA contactors and starters are designed to NEMA standards and are extremely rugged products and built for any application. Their long electrical/mechanical life is extended through easy maintainability. Meet and exceed all NEMA, UL and CSA standards. Sized based on standard NEMA classifications. Designed and built for a variety of demanding applications. Easy coil change and inspectable/ replaceable contacts. Adjustable/interchangeable heater packs for flexibility. Available in Open and NEMA 1, R, 4/4X and 1 enclosures. Freedom IEC Features Freedom IEC contactors and starters are designed to IEC standards and comply with the International Standard IEC 947-4-1. IEC products are a perfect choice when electrical and mechanical application parameters are known. They are typically smaller in size and provide higher ratings in a smaller package. They are available in sizes to match the contactor to the application. Complies with IEC 947-4-1, EN, CENELEC, UL and CSA standards. Sizes of contactors through 900 hp. DIN rail mountable through 0 hp. Adjustable bimetal overload relays fixed or interchangeable heater. Available in Open and NEMA 1, R, 4/4X and 1 enclosures. 0 1 6 7 8 9 1 4 6 8 CA0801E
.7- Motor Starters & Contactors Low Voltage Enclosures Catalog Numbering System January 00 Sheet 1184 0 1 6 7 8 9 1 4 Table.7-1. Enclosed Control Catalog Numbering System NEMA Design N = Freedom T = IT. Class 01 = Contactors 0 = Reversing Contactors 0 = FVNR Starter, Non-Combination 06 = Reversing, Non-Combination 07 = FVNR Non-Combination, with CPT 08 = Single-Phase FVNR (Freedom Only) 16 = Combination with Disconnect Switch 17 = Reversing, Combination with Disconnect Switch 18 = Combination with Disconnect Switch, with CPT = Combination with HMCP = Reversing, Combination with HMCP = Combination with HMCP with CPT = Multispeed SW Non-Combination 4 = Multispeed S1W CT or VT Non-Combination = Multispeed S1W CH Non-Combination 6 = Multispeed with Disconnect Switch, SW = Multispeed with Disconnect Switch, S1W CT or VT 8 = Multispeed with Disconnect Switch, S1W CH = Multispeed with HMCP, SW = Multispeed with HMCP, S1W CT or VT 41 = Multispeed with HMCP, S1W CH 4 = Autotransformer, Non-Combination 4 = Autotransformer, with Disconnect Switch 44 = Autotransformer, with HMCP 4 = Part-Winding, Non-Combination 46 = Part-Winding, with Disconnect Switch 47 = Part-Winding, with Thermal-Magnetic Circuit Breakers 48 = Y-D, Open Transition, Non-Combination 49 = Y-D, Open Transition, with Disconnect Switch 0 = Y-D, Open Transition, with Thermal-Magnetic Circuit Breakers 1 = Y-D, Closed Transition, Non-Combination = Y-D, Closed Transition, with Disconnect Switch = Y-D, Closed Transition, with Thermal-Magnetic Circuit Breakers 6 = Autotransformer Pump Panel, Disconnect Switch 6 = Autotransformer Pump Panel, HMCP 64 = Part-Winding Pump Panel, Disconnect 6 = Part-Winding Pump Panel, HMCP 68 = Duplex, Non-Combination 69 = Duplex, with Disconnect Switch 70 = Duplex, with HMCP ECN 1 A A F - NEMA Size A = 00 0 = 0 1 = 1 = = 4 =4 = 6 =6 7 =7 8 =8 9 =9 For IT., IEC and NEMA Starters, add an 11th character for the corresponding overload selection. For non-combination contactors and starters, include the letter (A) as the th character. A = None B = A/0 V R C = A/ V R D = 60 A/0 V R E = 60 A/ V R F = 0 A/0 V R A = None B = A C = 7 A D = 1 A E = A F = 0 A Cover Control (Starters Only) (See Tables.7-4 and.7- on Page.7-) Coil Voltage and/or Control Transformers (See Tables.7- and.7- Below) Modification Codes Disconnect Fuse Clip Ratings G = 0 A/ V R H = 00 A/0 V R J = 00 A/ V R K = 0 A/0 V R L = 0 A/ V R M = A/0 V R HCMP or Breaker Ratings G = 0 A H = A J = 0 A K = 0 A L = A M = 800 A Enclosure Types 1 = Type 1 General Purpose = Type R Rainproof = Type 4 Watertight (Painted Steel) 4 = Type 4X Watertight (Stainless Steel) = Type 4X Corrosion (Non-Metallic) 6 = Type 7/9 Bolted Hazardous Location 7 = Type 7/9 Threaded Hazardous Location 8 = Type 1 Dust-Tight N = A/ V R P = 800 A/ V L Q = 0 A/ V L R = 1 A/ V L S = 000 A/ V L T = by N = 00 A P = 0 A Q = 000 A R = 00 A T = by 6 8 Table.7-. Magnet Coil Codes (System Voltage) Code Voltage Code Voltage A B C D E G H J K L M /60 1/0 0/60 0/0 480/60 4/0 7/60 0/0 08/60 0/0 77/60 08 0/60 0/0 80/0 41/0 When control power transformer Modification Codes (CI CII) are used, pick the system (primary) voltage from this chart. See Table.7-. Note: All IT. contactors and starters are furnished with Vdc coil and control power supply. The eighth digit Q denotes separate Vdc control source. P Q R S T U V W X Y Z 1 Vdc Vdc 48 Vdc /1 Vdc /60 /0 /0 48/60 4 /60 48/0 By Table.7-. Control Power Transformer Codes (System Voltage) Code Primary Secondary B C D E H L M P Q R S T U V W X Y Z 0/480 0/4 Wired for 0 V 0/480 0/4 Wired for 0 V 7/60 0/0 08/60 77/60 80/0 41/0 /60 08/60 0/480 0/4 Wired for 0 V 0/480 0/4 Wired for 0 V 7/60 77/60 80/0 41/0 0/480/ Wired for 480 V 0/480/ Wired for 480 V By /60 1/0 /60 1/0 /60 1/0 /60 /60 1/0 1/0 Note: Use when ordering classes with CPT installed (i.e., ECN 18) and when using Modification Codes CI CII. CA0801E
January 00 Sheet 118 Motor Starters & Contactors Low Voltage Enclosures Catalog Numbering System.7- Table.7-4. Cover Control Non-Reversing Code A B C D E F G H J K L M N P Q R S T U V W X Z None Start/Stop Pushbuttons Start/Stop Pushbuttons, Run (R) Pilot Light Start/Stop Pushbuttons, Run (R), Off (G) Pilot Lights On/Off Pushbuttons On/Off Pushbuttons, Run (R) Pilot Light On/Off Pushbuttons, Run (R), Off (G) Pilot Lights Hand/Off/Auto Selector Switch Hand/Off/Auto Selector Switch, Run (R) Pilot Light Hand/Off/Auto Selector Switch, Run (R), Off (G) Pilot Lights Start Pushbutton On Pushbutton Off Pushbutton Run-Red Pilot Light Off-Green Pilot Light Run (R) - Off (G) Pilot Lights Start/Stop Selector Switch Start/Stop Selector Switch, Run (R) Pilot Light Start/Stop Selector Switch, Run (R), Off (G) Pilot Lights On/Off Selector Switch On/Off Selector Switch, Run (R) Pilot Light On/Off Selector Switch, Run (R), Off (G) Pilot Lights By Starters only contactor cover control: use Modification Codes. Table.7-. Cover Control Non-Reversing (Use for Class 06,, 17, 0,, 6) Code A B C D E F H J K P Q R V W X Z None Forward/Reverse/Stop Pushbuttons Forward/Reverse/Stop Pushbuttons, Red Pilot Lights Forward/Reverse/Stop Pushbuttons, Red, 1 Green Pilot Lights Up/Stop/Down Pushbuttons Up/Stop/Down Pushbuttons, Red Pilot Lights Forward/Off/Reverse Selector Switch Forward/Off/Reverse Selector Switch, Red Pilot Lights Forward/Off/Reverse Selector Switch, Red, 1 Green Pilot Lights Red Pilot Lights 1 Green Pilot Light Red, 1 Green Pilot Lights Open/Off/Close Selector Switch Open/Off/Close Selector Switch, Red Pilot Lights Open/Off/Close Selector Switch, Red, 1 Green Pilot Lights By Starters only contact or cover control: use Modification Codes. 0 1 6 7 8 9 1 4 6 8 CA0801E
.- Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line General January 00 Sheet 1118 0 1 6 7 8 9 1 4 6 8 Freedom Enhancements 6 mm Contactor Accessible Power Terminations to Facilitate Installation The 6 mm contactor housing has been completely redesigned to open up the line/load terminal access area, allowing better visibility when wiring. This also aids in maintenance. IP0 fingerproofing is available through add-on shields. This change affects NEMA Sizes 1 and. Load Lugs on Overload Relay Base The load lugs have been moved from the heater pack housing to the sensor base of the A and 7 A overload relays. This permits wiring of the starter prior to heater pack installation. These overload relays are used on NEMA Sizes 00 and 8. Auxiliary Contact Markings CENELEC EN001 All auxiliary contact blocks are identified by a two-digit contact configuration code. Auxiliary contact terminals are also identified by a two-digit number in accordance with International Standards approved by CENELEC. Auxiliary Contact Ratings All side and top auxiliary contact blocks are now rated NEMA/UL P0 dc ratings and IEC 947 AC-1/DC-1 ratings. Larger IEC Contactors There are three additional frame sizes a 0 mm contactor (CE1T and U) rated 0 and hp respectively; a 80 mm contactor rated 0 hp at V; and a mm contactor rated 900 hp at V. New Class and 0 Heater Packs Because of improvements in the overload relays, the Class and 0 interchangeable heater packs have been modified. They can be used with the new overload relays (Series B1) directly or with the existing relays (Series A1) when using an adapter lug kit. Series B1 A Overload AE17/7 IEC Fixed Heater Starters, IEC 947-4-1 Completely assembled IEC 947-4-1 starters can be ordered in non-reversing and reversing, open or enclosed. This starter line is composed of CE1 contactors and C16 fixed heater overload relays. AE17 Fixed Heater IEC Starter Size K Easy Magnet Coil Change The 6 mm contactor and the connections on the 4 and 6 mm starters have been modified to allow easy coil changes at the distributor or in the field. Standards and Certifications Standard: Designed to meet or exceed UL, NEMA, IEC, CSA, VDE and BS. UL listed: UL File #E1491, Guide #NLDX Open; UL File #E1761 Enclosed Combination Motor Controllers; UL File #E19 Enclosed Non-Combination Motor Controllers; UL File #E19 Enclosed Power Conversion Equipment. CSA certified: CSA File #LR, Class #14 Open and NEMA 1 Enclosed. IEC: IEC 947-4-1, Sizes 6 8 (A S); IEC 18, Sizes T Z; IEC 947 Pending. Certified Type Coordination Cutler-Hammer Freedom Series IEC starters and NEMA starters are now UL certified to achieve IEC 947 Type coordination against 0,000 A short circuit fault currents. Any brand of properly selected fuse can be used. Type coordination means that the starter will be suitable for further use following a short circuit fault. ISO 9000 Certification When you turn to Eaton s Cutler- Hammer products, you turn to quality. The International Standards Organization (ISO ) has established a series of standards acknowledged by 91 industrialized nations to bring harmony to the international quest for quality. The ISO certification process covers 0 quality system elements in design, production and installation that must conform to achieve registration. This commitment to quality will result in increased product reliability and total customer satisfaction. Short Circuit Protection Fuses and Inverse-Time Circuit Breakers may be selected per Article 4, Part D of the National Electrical Code to protect motor branch circuits from fault conditions. If higher ratings or settings are required to start the motor, do not exceed the maximum as listed in Exception No., Article 4-. Contactor Terminal Markings Contactors are identified by a two digit number in accordance with International Standards approved by CENELEC (European Committee for Electrotechnical Standardization). This distinctive number is marked on the top nameplate and designates the type and quantity of built-in auxiliary contacts. The first digit indicates the quantity of NO and the second digit indicates the quantity of NC contacts. Example: E indicates a contactor with 1NO and no NC auxiliary contacts factory supplied. In addition, all terminals conform to both CENELEC and NEMA requirements. Auxiliary contact terminals use the first digit to indicate location and the second digit to indicate status (1- means NC and -4 means NO). Example: 1-14 indicates the first auxiliary contact and it is a NO. -Pole A1 A A 1 L1 L Figure.-1. Contact Example When Supplied L 1 T1 T T 14 4 6 CA0801E
January 00 Sheet 1119 Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line Technical Data NEMA Contactors and Starters.- NEMA Sizes 00-8 Table.-1. ac Coil Data NEMA Sizes Motor Voltage 00 00 7 0 00 7 1 00 7 00 7 00 7 4 00 7 00 7 6 00 7 7 7 8 7 Maximum hp Rating 1-1/ 1-1/ 7-1/ 7-1/ 1 0 0 0 0 0 7 0 00 00 00 0 0 0 900 900 0 % of rated coil voltage. P.U. Volts P.U. Sealed D.O. Volts Maximum Operation Cold Hot Var VA Watts Var VA Watts Cold Hot Rate Operations/Hour P.U. Time ms 74% 78% 64 80 49 7.1 7..4 4% 46% 1,000 1 1 74% 78% 78 0 6 9..1 4% 46% 1,000 1 1 74% 78% 9 7 8 7.8 49% 0% 1,000 0 14 74% 78% 9 7 8 7.8 49% 0% 1,000 0 14 7% 76% 4 0 11 48 49.8 1 0% % 7,00 14 11 7% 76% 11 118 0 96 0 7. 4% 6%,0 8 14 7% 77% 11 118 0 96 0 7. 6% 64%,0 1 7% 7% 868 1 14 11 00 7% 7% 868 1 14 11 0 00 7% 7% 16 0 060 6 7 60 70 0 D.O. Time ms 0 1 6 7 8 9 1 General Coil Data Coil Offering tape wound: NEMA Sizes 00 0 UL Insulation Rating: Class 1 (B) Coil Offering encapsulated: NEMA Sizes 1 UL Insulation Rating: Class 1 (A) Coil Offering encapsulated: NEMA Sizes 4 UL Insulation Rating: Class 1 (F) Operational Limits: 8% to 1% of rated voltage ac 80% to 1% of rated voltage dc Table.-. Coil Data Notes P.U. Pickup time is the average time taken from closing of the coil circuit to main contact touch. D.O. Dropout time is the average time taken from opening of the coil circuit to main contact separation. Cold Coil data with a cold coil. Hot Coil data with a hot coil. All data is based on a standard contactor with no auxiliary devices and a Vac or Vdc magnet coil. Coil data has a ±% range depending on the application, therefore specific data may vary. 4 6 8 CA0801E
.-4 Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line Technical Data NEMA Contactors and Starters January 00 Sheet 1 0 1 6 7 8 9 1 4 6 8 Table.-. dc Coil Data NEMA Sizes Motor Voltage 00 and 0 1 48 1 and 1 48 1 48 4 and 48 0 6 6 14 4 7 6 14 4 8 6 14 4 Change amature, magnet and amature interlock after 1 x operations. General Coil Data Coil Offering tape wound: NEMA Sizes 00 0 UL Insulation Rating: Class 1 (B) Coil Offering encapsulated: NEMA Sizes 1 UL Insulation Rating: Class 1 (A) Coil Offering encapsulated: NEMA Sizes 4 P.U. Sealed D.O. Volts Amperes Watts Volts (Hot) Amperes Watts (Hot) 6.4. 1.6 0.64 1.4 6..9 1.1 1 6.1. 18 9.0. 1.7 8. 4.1.6.0 1.9 6.9 4..4 19.8 9.8 6. 4.9 76.8 76.8 76.8 76.8 16 88.4 76. 67. 9 88 9 98 0 0 4 77 77 77 77 14 14 14 14 0 0 0 0 UL Insulation Rating: Class 1 (F) Operational Limits: 8% to 1% of rated voltage ac 80% to 1% of rated voltage dc 80% 80% 80% 80% 68% 60% 6% % 6% 61% 6% 61% 67% 67% 6% 64% 0.8 0.14 0.07 0.08 0.4 0.1 0.11 0.041 0. 0.0 0.097 0.08 0. 0.11 0.0 0.0 0.08 0.04 0.06 0.01 0.184 0.091 0.07 0.04 0.66 0.80 0.176 0.1.6.6.6.6 4.98 4.96.04 4.87 4.84 4.7 4.67 4.7...4 4.9 Table.-4. Coil Data Notes 9 9 9 9 19. 19. 19. 19. 60 60 60 60 60% 60% 60% 60% % 9% 8% 9% % % % % % % 8% 6% P.U. Time ms 1 0 0 0 8 49 6 49 P.U. Pickup time is the average time taken from closing of the coil circuit to main contact touch. D.O. Dropout time is the average time taken from opening of the coil circuit to main contact separation. Cold Coil data with a cold coil. Hot Coil data with a hot coil. D.O. Time ms 17 17 17 17 1 1 14 16 14 14 14 16 14 16 19 1 Maximum Operation Rate Operations/Hour,0,0,0,0,0,0,0,0 1,00 1,00 1,00 1,00 Mechanical Life Millions All data is based on a standard contactor with no auxiliary devices and a Vac or Vdc magnet coil. Coil data has a ±% range depending on the application, therefore specific data may vary. CA0801E
January 00 Sheet 111 Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line Technical Data NEMA.- Table.-. Specifications Sizes 00 Contactor Catalog Number/Size Configuration Number of Poles Auxiliary Contacts, Standard Add-on Auxiliary Contacts CN1A NEMA Size 00,, 4 4th Pole NO (1) Top (4) or Side (4) CN1B NEMA Size 0, Top (4) or Side () CN1D NEMA Size 1,, 4, Top (4) or Side () CN1G NEMA Size,, 4, Top (4) or Side () CN1K NEMA Size Frame Size 4 mm 4 mm 6 mm 6 mm 90 mm Maximum Voltage Rating Vac Vac Vac Vac Vac Continuous Ampere Ratings (I) 9 Amperes 18 Amperes 7 Amperes 4 Amperes 90 Amperes Maximum Horsepower (hp) 1-Phase 11 V V 1/ 1 1 7-1/ 7-1/ 1 -Phase 00 V V V 7 V Coil Operating Range % of Rated Voltage Operating Temperature Maximum Operating Altitude in Feet (m) Mechanical Life Electrical Life (480 V/60 Hz) AC- AC-4 Wire Range Power Terminals Control Terminals Power Terminal Torque Line and Load lb-in Auxiliary Contact Rating 1-1/ 1-1/ 7-1/ 7-1/ -1% to +% -1% to +% -1% to +% -1% to +% -1% to +% -0 to 6 C 6,000 (188) 0,000,000 4,000,000 90,000 1 16 Stranded, 1 14 Solid Cu 1 16 Stranded, 1 14 Solid Cu -0 to 6 C 6,000 (188) 0,000,000,000,000 8,000 8 16 Stranded, 14 Solid Cu 1 16 Stranded, 1 14 Solid Cu -0 to 6 C 6,000 (188),000,000,000,000 00,000 8 14 Stranded or Solid Cu 1 16 Stranded, 1 14 Solid Cu 1-0 to 6 C 6,000 (188),000,000,00,000 6,000 14 (Upper) and/ or 6 14 (Lower) Stranded or Solid Cu 1 16 Stranded, 1 14 Solid Cu 7 1 0 (14 8 AWG) 4 (6 4 AWG) 0 ( AWG) A, P0, Left Side (4) or Right Side () 0 0-0 to 6 C 6,000 (188) 6,000,000 1,700,000 80,000 1/0 14 Cu 1 16 Stranded 1 14 Solid Cu (14 AWG) (8 AWG) 4 (6 4 AWG) 0 ( 1/0 AWG) 0 1 6 7 8 9 1 4 6 8 CA0801E
.-6 Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line Technical Data NEMA January 00 Sheet 11 0 1 6 7 8 9 Table.-6. Specifications Sizes 4 8 Contactor Catalog Number/Size Configuration Number of Poles Auxiliary Contacts, Standard Add-on Auxiliary Contacts CN1N NEMA Size 4, Left Side () or Right Side (4) CN1S NEMA Size, Left Side () or Right Side (4) CN1T NEMA Size 6 Top Left NO/NC (1) Top Right NO/NC (1) CN1U NEMA Size 7 Top Left NO/NC (1) Top Right NO/NC (1) CN1V NEMA Size 8 Side NO/NC (1) NO/NC () Frame Size 180 mm 180 mm 80 mm 80 mm 4 mm Maximum Voltage Rating Vac Vac Vac Vac Vac Continuous Ampere Ratings (I) 1 Amperes 70 Amperes Amperes 8 Amperes 11 Amperes Maximum Horsepower (hp) 1-Phase 11 V V -Phase 00 V V V 7 V Coil Operating Range % of Rated Voltage Operating Temperature Maximum Operating Altitude in Feet (m) Mechanical Life Electrical Life (480 V/60 Hz) AC- AC-4 Wire Range Power Terminals Control Terminals 0 0 0 7 0 00 00 00 0 0-1% to +% -1% to +% -1% to +% -1% to +% -1% to +% -0 to 6 C 6,000 (188),000,000 800,000 70,000 Open /0 8 Cu; Enclosed 0 kcmil 6 Cu/Al 1 16 Stranded, 1 14 Solid Cu -0 to 6 C 6,000 (188),000,000 00,000 4,000 70 kcmil or () 0 kcmil /0 Cu/Al 1 16 Stranded, 1 14 Solid Cu -0 to 6 C 6,000 (188),000,000 90,000 7,0 () 70 kcmil /0 Cu/Al 1 16 Stranded, 1 14 Solid Cu 00 0-0 to 6 C 6,000 (188),000,000,000,000 () 70 kcmil /0 Cu/Al 1 16 Stranded, 1 14 Solid Cu 0 900 900-0 to 6 C 6,000 (188),000,000,000 4,00 (4) 70 kcmil 1/0 Cu/Al 1 16 Stranded, 1 14 Solid Cu 1 4 6 8 Power Terminal Torque Line and Load lb-in Auxiliary Contact Rating 00 0 0 0 00 A, P0 CA0801E
January 00 Sheet 11 Motor Starters & Contactors Low Voltage Motor Starters Electromechanical Freedom Line Technical Data NEMA.-7 Table.-7. 80 Volts, 0 Hz Starters Maximum hp Ratings Table.-8. Motor FLA Current Ranges Size 1 Lower Current Range for motor hp range 1/4 hp to hp at V. Table.-9. Maximum Horsepower Rating of Starters for 80 V, 0 Hz Application Table.-. Wire (7 C) Sizes AWG or kcmil NEMA Sizes 00 Open and Enclosed Two compartment box lug. NEMA Size 1 4 6 Maximum hp 0 7 0 1.1 to 1. S.F. NEMA Size 1 1 4 6 0.47.81 1.0 S.F. 0.1 4.14.1 7.00.4 7.00.1 4.00.4 4.00 9.90 90.00.80 90.00 9.90 1.00.80 1.00 Table.-11. Power Terminals Load Cu Only (Stranded or Solid) 8. 70.00 41.70 70.00 Minimum per NEC. Maximum wire size: Sizes 00 and 0 to #8 and Sizes 1 to #. 8..00 41.70.00 IEC Size A B C D E F G H J K L M N P R S hp 1 0 0 60 7 0 1 NEMA Size Power Terminals Line 00 0 1 Heater Pack Catalog Numbers H001B H0B H011B H01B H01B, H014B H01A H017A H01B H016B H017B Cu Only #1 #16 Stranded, #1 #14 Solid #8 #16 Stranded, # #14 Solid #8 #14 Stranded or Solid # #14 (Upper) and/or #6 #14 (Lower) Stranded or Solid Minimum #14 #1 # #8 #14 # #6 #4 # Control Terminals Cu Only #1 #16 Stranded, #1 #14 Solid Heater Pack Catalog Numbers H1B H1B H111B H11B H11B, H114B H114 H117 H11B H116B H117B Minimum #14 #1 # #8 #14 # #6 #4 # Table.-1. Wire (7 C) Sizes AWG or kcmil NEMA Sizes 8 Open and Enclosed NEMA Size Wire Size Power Terminals Line and Load #1/0 #14 Al Cu 4 Open #/0 #8 Cu Enclosed 0 kcmil #6 Al Cu 70 kcmil # or () 0 kcmil #/0 Al Cu 6 () 70 kcmil #/0 Al Cu 7 () 70 kcmil #/0 Al Cu 8 (4) 70 kcmil #1/0 Al Cu Control Terminals Cu Only #1 #16 Stranded, #1 #14 Solid 0 1 6 7 8 9 1 4 6 8 CA0801E