PUPE OPIS Ova familija pumpi primenjuje se u zatvorenim hidrauličkim sistemima servoupravljanja na motornim vozilima, ali može da ima primenu i u drugim hidrauličkim sistemima. Ove pumpe se pokreću pogonskim motorom preko odgovarajuće spojnice, zupčanika, remenice ili vratila kompresora. Kod pogona pumpe obratiti pažnju na sledeće: - Kod pogona preko remenice ili zupčanika treba imati u vidu da je mogućnost nošenja radijalnih sila ograničena, pa je potrebno konsultovati proizvođača. - Kod pogona preko kompresora prenos obrtnog momenta sa vratila kompresora na vratilo pumpe treba da se ostvaruje spojnicom koja dozvoljava vrlo mala odstupanja u saosnosti. - Obrtanje pumpe sme da bude samo u naznačenom smeru. - Pumpu ugraditi tako da joj usisni vod bude ispod nivoa rezervoara iz koga usisava radnu tečnost, a vod za usisavanje je preporučljivo da bude što kraći i sa što manje krivina. psolutni pritisak u usisnom vodu sme da bude najmanje 0,85 bar pri temperaturi od 50 C, s tim da se ne 2 prekorači viskozitet od 27 mm / s. - ko se koristi pumpa bez ugrađenog ventila za ograničenje pritiska, isti treba predvideti posebno ili ga ugraditi u hidraulički servoupravljač ( u hidrauličkom sistemu ne smeju da se nađu dva ventila sigurnosti ). PUPS DESCRIPTION: This family of pumps is mainly applied to closed-loop hydraulic servo steering system on motor vehicles, but it can also be applied to other hydraulic system. These pumps are put into operation by means of drive motor via corresponding coupling, gear, pulley of compressor shaft. Regarding pump drive, special attention should be paid to the following: - In case of pulley or gear drive always bear in mind that the capability to withstand radial forces is limited, so it is necessary to consult the manufacturer. - In case of drive via compressor, transmission of the torque from the compressor shaft to the pump shaft should be effected by a coupling which allows only for small deviations from axial alignment. - The pump is allowed to rotate only in specified direction. - The pump is to be mounted in such a way that its suction line lies below the level of the tank from which working fluid is "sucked in", and suction line is recommended to be as short as possible, the fewer curves the better. The absolute permissible pressure within the suction line should be min. 0,85 bar at the temperature of 2 50 C, and the viscosity of 27 mm /s is not to be exceeded. - In case the pump without pressure-relief valve is used, the valve is to be provided separately or otherwise installed within hydraulic servo steering gear (there should not be two safety valves within a single hydraulic system). -1
Tip: standard TEHNIČKE KRKTERISTIKE TECHNICL DT: Type: standard VNE PUPS Oznaka Specif. Regul. ax. roj obrtaja protok protok pritisak Pogon Designation Speed (potisni vod asa Simbol Napomena Specific Regul. ax. (min -1 ) na kućištu) Drive levi smer desni smer flow flow ass Symbol Note press. (press. line CCW CW (cm 3 /o) (l/min) (bar) min max at the case) (kg) 138-2 135 138-2200 138-2200S 9 130 138-2300 138-4000 4673 011 83 155 vid. napom. c 4673 0 see note 1 k o 0 o 4673 013 m m 4673 014 70 p p 4673 015,5 130 3,7 r r 4673 0 e e s 4673 017 7 s x1,5 s 4673 018 9 80 o o vid. napom. 4673 019 see note 1 r r 130 4673 020 x1,5 500 3500 4673 021 4673 022 4,2 4673 023 130 vid. napom. 4673 1 see note 1 4673 7 3,7 4673 8 4673 156 4673 176 x1,5 4674 076 / IR 6,0 20 4674 145 135 4,5 4673 071 6,0 4673 072 130 4673 073 5,2 2 4673 074 6,0 4673 075 0 5,3 2 4673 076 5,7 4673 077 x1,5 5,5 2 4673 078 130 6,0 z u 4673 079,5 p x1,5 5,5 g 4673 139 č e a 4673 154 a 660 3360 6,0 ni 4673 1 135 k 4673 211 x1,5 4673 213 0 5,5 4673 217 4673 311 2 130 4673 322 4674 077 6,0 3500 x1,5 4674 117 150 20 4674 207 5,5 2 4674 232 130 6,0 p e m u e l n l ic e a y 4673 051 4672 253 14 130 6,5 4673 040 x1,5 4673 041 9 4,5 4673 043 70 4673 044 * 500 1500 3,6 C * n=0 min -1 4673 045 vid. napom. see note 4,5 1 130 4673 046 4673 047,5 0 x1,5 6,5 4,5 4673 049 7,8 3500 4673 5 x1,5 4,5 4673 132 4673 182 4673 554 x1,5 4677 106 32,8 130 x1,5 10,0-2
Type: standard VNE PUP Tip: standard C Položaj ugradnje ounting position mineralno ulje Radna mineral oil tečnost viskozitet viscosity Working temperatura temperature fluid tačka stinjavanja coagulation point (mm 2/s) proizvoljan optional GENERL OTORS DEXRON II pri 27 ( 50 C) ( C) from -20 to + ( C) -35 od at do Napomena : 1 - Pumpa sa ugrađenim uvrtnim priključcima: - usisni vod: 22 L JUS.6.720 (30x2) - potisni vod: L JUS.6.720 () 2 - Pumpa bez zupčanika na izlaznom vratilu Note : 1 - Pump with built-in threaded ports - suction line: 22 L JUS.6.720 (30x2) - pressure line: L JUS.6.720 () 2 - Pump without outlet shaft gearing ( l/min ) Protok Flow 19 18 17 15 14 13 11 10 9 8 7 6 5 4 3 2 1 500 0 bar Protok Flow 0 50 bar Prazan hod motora Idle motion of motor 1500 Za grupu 4673 For group 4673 Regulisan protok (l/min) Regulated flow Regulisan protok Regulated flow (l/min) Regulisan protok Regulated flow 9 (l/min) 2000 2500 bar 80 bar 60 bar 40 bar 3000 20 bar 10 bar 3500 roj obrtaja Speed 4000-1 ( min ) 4500 28,5 27,0 25,5 24,0 22,5 21,0 19,5 18,0,5 15,0 13,5,0 10,5 9,0 7,5 6,0 4,5 3,0 1,5 (kw) Pogonska snaga Drive power KRKTERISTIČNI DIJGRI CHRCTERISTIC DIGRS NRUČIVNJE ORDERING Pumpe se naručuju po oznakama iz tabele Pumps to be ordered according designations from the table. UGRDNI CRTEŽ OUNTING DRWING Pogon preko kompresora Compressor drive Opšti crtež General drawing 45x3,6 samo za 4673 018 45x3,6 only for 4673 018 50 O prsten O ring 47x2,6 FS1.0002 Del. pogled Partial view 89,5 37 Ø54 samo za 4673 018 Ø54 only for 4673 018-3
Tip: standard Type: standard VNE PUPS Only for 138-2 89,5 Only for 138-2200S 4 vijka 8x40 (sa podloškama i navrtkama) 4 screws 8x40 (with nuts and washers) Only for 138-4000 52 ±0 1, 52 ±0 1, 14 77 Ø26 44 18 +0,1-0,3 +0,1-0,3 Seal OR47x2,6 FS1.0002 Ø30 30 18X1,5 Ø10,5 15 R 50 46 62 Ø88 21 ±0,1 8e10 4 Ø52g6 R0,1 +0,2 To steering gear Ka upravljaču Od rezervoara From reservoir 37 20 11,5 +0,15-0,35 ~41 26X1,5 Ø38 3 +0,3 ~57 ~47,5 Delimični pogled Partial view 101 R 15 +0,2 R0,1 Ø24 +0,1 4,5 9 +0,2-4
Type: standard VNE PUP Tip: standard Only for 4673 022 Only for 4674 076/IR 26x1,5 Only for 4674 145-5
Tip: standard Type: standard VNE PUPS Pogon preko zupčanika Gear drive Opšti crtež General drawing O-ring 90x4 d= 0 Only for 4673 073 Presek - Section - 3,5 6P9 Ø20k6 Only for 4673 075 Ø88 O-ring 90x4-6
Type: standard VNE PUP Tip: standard Only for 4673 076 O-ring 64,2x3 FS1.0002 =20 Ø72-0,03 Only for 4673 077 41,4 Only for 4673 078-7
Tip: standard Type: standard VNE PUPS Only for 4673 139 4673 211 Only for 4673 213 Presek - Section - 4673 322 Only for Ø105g6 Ø Ø konus 1:10 cone 1:10 Ø88 x26x1,5 klin JUS.C2.050-5x7,5 axle-pin -8
Type: standard VNE PUP Tip: standard Only for 4674 077 4674 117 oment pritezanja 80Nm Tightening torque dub. depth dub. depth 4674 232 Only for Ø Ø Presek - Section - 4673 217 Only for -9
Tip: standard Type: standard VNE PUPS Only for 4673 311 O-ring 90x4 Pogon preko remenice Pulley drive Opšti crtež General drawing oment pritezanja 60Nm Tightening torque Presek - Section - Ø88 Only for 4672 253 Detalj x Detail x -10
3-30 Type: standard VNE PUP Tip: standard Only for 4673 046 Only for 4673 049 Ø 27 Ø25 4,5 8 ~ 80 ~ 47,5 9,7 37,8 ~ 67 20 17 42,2 21,3 45 28 10x10,5 +0.1 ~22,5 62 R 17 59-103 +0.2 65-98 30 Ø119,5 44 D etalj "X" Detail ±30' 34 30 Ø24 Ø11 11,5 ±0.1 ±0.1 48 48 205 Ø15 (2x) Ø28 (2x) 11 (3x) 91 ±1 28,7-11
Tip: standard Type: standard VNE PUPS Ostali pogoni Others 4677 106 Only for č č -
Tip:luminijumsko kućište VNE PUPS Type: luminium case TEHNIČKE KRKTERISTIKE TECHNICL DT: Oznaka Specif. Regul. ax. roj obrtaja protok protok pritisak Pogon Designation Speed asa Simbol Napom. Specific Regul. ax. (min -1 Drive flow flow ) ass Symbol Note press. levi smer desni smer (cm 3/o) CCW CW min max (cm 3 (l/min) /rev) (bar) (kg) 4684 010 150 c 4684 015 130 1 k o o 4684 0 m 0 m p p 4684 104 180 r r 17 e e 4684 105 s o 4684 106 83 500 3500 x1,5 2,3 s r o 4684 109 7 r 180 4684 114 4684 134 1 4685 010 20 130 21 4685 137 150 Položaj ugradnje proizvoljan ounting position optional mineralno ulje GENERL OTORS DEXRON II Radna mineral oil viskozitet (mm 2/s) pri tečnost viscosity 27 ( at 50 C) Working temperatura od do temperature ( C) from -20 to + fluid tačka stinjavanja coagulation point ( C) -35 Napomena : 1 - Pumpa sa ugrađenim uvrtnim priključcima: - usisni vod: 22 L JUS.6.720 (30x2) - potisni vod: L JUS.6.720 () Note : 1 - Pump with built-in threaded ports - suction line: 22 L JUS.6.720 (30x2) - pressure line: L JUS.6.720 () UGRDNI CRTEŽ OUNTING DRWING -13
GEROTOR PUPE GEROTOR PUPS TEHNIČKE KRKTERISTIKE TECHNICL DT: Simbol Symbol Oznaka Specif. Regul. ax. roj obrtaja protok protok pritisak Pogon Designation Speed asa Napom. Specific Regul. ax. Drive (min -1 ) ass Note flow flow press. levi smer desni smer (cm 3/o) CCW CW min max (cm 3 /rev) (l/min) (bar) (kg) 1014 1,5 140 600 3500 5,3 Položaj ugradnje proizvoljan ounting position optional mineralno ulje Radna mineral oil GENERL OTORS DEXRON II viskozitet (mm 2/s) pri tečnost viscosity 27 ( at 50 C) Working temperatura od do temperature ( C) from -20 to + fluid tačka stinjavanja coagulation point ( C) -35 UGRDNI CRTEŽ OUNTING DRWING -14