INSTALL GUIDE DOCUMENT NUMBER 979 REVISION DATE 070 FIRMWARE OEM-AL(RS)-FM8-[ADS-ALCA] HARDWARE ADS-ALCA ESSORIES ADS-USB (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 07 BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE OF DOC.: #979 070 VEHICLE LIST - OF FEATURES MODEL YEAR DATA IMMOBILIZER BYPASS X LOCK /STANDALONE MOD. DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TACHOMETER STATUS HOOD STATUS OUTPUT* BRAKE PEDAL STATUS OUTPUT RAP SHUTDOWN CTRL HEATED MIRRORS CTRL HEATED SEATS CTRL REAR DEFROST CTRL TRUNK RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT POWER LIFTGATE NOTES Edge STD key AT -7 Edge PTS AT -7 Explorer PTS AT -7 F-0 STD key w/oem Keyless Entry -7 F-0 PTS AT -7 F-0 / F-0 / F-0 STD key w/oem Keyless Entry 7 F-0 / F-0 / F-0 PTS AT 7 Fusion STD key AT -7 Fusion Hybrid STD key AT -7 Fusion PTS AT -7 Fusion Hybrid PTS AT -7 Continental PTS AT 7 MKC PTS AT -7 MKZ PTS AT -7 MKZ Hybrid PTS AT -7 LINCOLN FORD INSTALL TYPE MAKE I Vehicle must be equipped with an active OEM hood switch. *Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 07
PAGE OF DOC.: #979 070 BOX CONTENTS - OF BOX CONTENTS WHITE WHITE PIN BLACK CONNECTOR PIN WHITE CONNECTOR MODULE 7 WHITE BLUE PROGRAMMING BUTTON 0 PIN BLACK CONNECTOR 7 PIN WHITE CONNECTOR LED A B F C E D 0 9 8 7 BLACK PIN WHITE CONNECTOR DATA CABLE PIN BLUE CONNECTOR DATA CABLE BLACK DATA PORT (WEBLINK, RF, TELEMATIC) WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 07
PAGE OF DOC.: #979 070 7 FORD F-0 / F-0 / F-0 STD key w/oem Keyless Entry / PTS AT Edge STD key / PTS AT Explorer PTS AT -7 Automotive Data Solutions Inc. 07 POLARITY MODULE LOCATION COMPONENT LOCATOR 0 White/Blue 9 White Gray/Orange Purple/Orange V Green/Red /Purple pin Gray WIRE COLOR HS CanH HS CanL CONNECTOR NAME POSITION WIRE DESCRIPTION CONNECTOR TYPE -7 CONNECTOR COLOR F-0 STD key w/oem Keyless Entry / PTS AT YEAR MODEL MAKE TYPE - WIRE CHART - OF pin 0 /Purple HS CanH 0 White/Blue HS CanL 9 White Gray/Orange Purple/Orange V Green/Red /Purple pin Gray pin 0 /Purple HS CanH 0 Blue Gateway module, right of steering column HS CanL 9 White Gateway module, right of steering column Gray/Orange Gateway module, right of steering column Purple/Orange Gateway module, right of steering column V Gray/Red Gateway module, right of steering column /Blue Gateway module, right of steering column pin Gray pin 0 /Blue HS CanH 0 White/Blue HS CanL 9 White Gray/Orange Purple/Orange V Gray/Red /Blue pin Gray pin 0 /White
PAGE OF DOC.: #979 070 LINCOLN MKC PTS AT MKZ / MKZ Hybrid PTS AT -7 - Automotive Data Solutions Inc. 07 COMPONENT LOCATOR 0 Blue 9 White Gray/Orange Purple/Orange V Gray/Red /Blue pin Gray pin 0 /Blue HS CanH 0 Blue HS CanL 9 White Gray/Orange White V Gray/Red /Blue pin Gray WIRE COLOR HS CanH HS CanL CONNECTOR NAME MODULE LOCATION WIRE DESCRIPTION POLARITY 7 POSITION -7 CONNECTOR TYPE Continental PTS AT YEAR MODEL Fusion / Fusion Hybrid STD key / PTS AT CONNECTOR COLOR FORD MAKE TYPE - WIRE CHART - OF pin 0 /Blue HS CanH 0 White/Blue HS CanL 9 White Gray/Orange Purple/Orange V Gray/Red pin Gray pin 0 /Purple HS CanH 0 Blue HS CanL 9 White Gray/Orange Purple/Orange V Gray/Red /Blue pin Gray pin 0 /Blue
PAGE OF DOC.: #979 070 TYPE - WIRING DIAGRAM - OF MODULE GATEWAY OR OBD MODULE A B F STEP C E DATA D A B MS CANL - MS CANH - 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) STEP 7 0 PINK (NC) 0 PINK/BLACK (NC) 0 ORANGE (NC) 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK (NC) 0 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 0 WHITE - PARKING LIGHT OUTPUT 0 WHITE/RED - RS ENABLE CONNECTOR SIDE 0 WHITE/BLACK - RS ENABLE VEHICLE SIDE C D CONNECT TEMPORARILY SEE PROGRAMMING PROCEDURE BLACK CONNECT TO VEHICLE SEE PROGRAMMING PROCEDURE 0 9 8 7 0 9 8 7 HS CANL - 9 HS CANH - 0 STEP CONNECT TO VEHICLE GROUND - E A V - SELECT ONE OF THE TWO OPTIONS 0 0 0 0 BLUE/WHITE (NC) WHITE (NC) BLACK - GROUND RED - V PARKING LIGHTS SWITCH WITHOUT A COMPATIBLE ESSORY: CONNECT V AND GROUND FROM MODULE TO VEHICLE. BLACK OR F 7 8 9 0 DATA CABLE GROUND V RS ENABLE - 0 WITH A COMPATIBLE ESSORY: SEE THE COMPATIBLE ESSORIES PAGE FOR DETAILS. 9 0 7 8 PARKING LIGHT - 0 GREEN/BLACK (NC) 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc. 07
PAGE 7 OF DOC.: #979 070 MODULE PROGRAMMING PROCEDURE - OF 0 0 CONNECT every wire shown in STEP and STEP of the wiring diagram. 07 Set ignition to ON position. 08 ON DISCONNECT every wire shown in STEP and CONNECT every wire shown in STEP of the wiring diagram. ON Wait, LED will turn solid RED. 09 Wait, LED will turn solid RED. 0 Wait, LED will flash GREEN once [x]. 0 Wait, LED will flash GREEN rapidly. 0 Wait, LED will turn solid RED. Wait, LED will turn solid GREEN for seconds. Set ignition to position. Module Programming Procedure completed. Set ignition to ON position. 0 0 ON Automotive Data Solutions Inc. 07 Set ignition to position. ON
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within 7 seconds. 0 ON PAGE 8 OF DOC.: #979 070 To exit valet mode: repeat steps to. Cycle ignition ON five times [x /ON] rapidly. 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. ON 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 07
PAGE 9 OF DOC.: #979 070 MODULE NAVIGATION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 Module must be programmed to the vehicle. 0 Use the Module Navigation Chart on the next page. 0 Set ignition to position. 07 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 ON TO ESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. 0 0 [X] Automotive Data Solutions Inc. 07
PAGE 0 OF DOC.: #979 070 [Z] SETTINGS I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. [Y] OPTIONS MODULE NAVIGATION CHART: NOTES [X] MENUS MODULE NAVIGATION CHART - OF 0-0 N/A 0 N/A 0 ENABLE 0 DISABLE* 0 N/A 0 DISABLE 0 N/A 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN** 0 0 MIN** 07 MIN** 08 MIN 09- N/A 0 N/A 0 0 N/A 0 TAKEOVER 0 N/A 07 0 FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 0-07 Technical Support only MODULE RUN TIME N/A *Vehicle will shutdown when a door is opened. **The maximum runtime for 0 models is x 0 minutes or x minutes. Automotive Data Solutions Inc. 07
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. REMOTE ER ERROR CODES: NOTES Automotive Data Solutions Inc. 07 PAGE OF DOC.: #979 070
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Automotive Data Solutions Inc. 07 DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE OF DOC.: #979 070
MODULE RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. Failure to follow procedure may result with a DTC or a CHECK error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. 07 PAGE OF DOC.: #979 070
TAKEOVER PROCEDURE - OF All vehicle doors must be closed and locked prior to remote start sequence. 0 Press unlock on OEM or aftermarket remote or request switch. 0 ON PAGE OF DOC.: #979 070 DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait seconds for key validation. 0 Press and release BRAKE pedal. 0 Take over procedure completed. Failure to follow procedure will result in vehicle engine shutdown. Automotive Data Solutions Inc. 07
INSTALLATION CHECKLIST - OF PAGE OF DOC.: #979 070 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. Exit vehicle. Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Automotive Data Solutions Inc. 07