Facts and figures ALLROUNDER 275 V Vertical free-space system Clamping force: 250 kn Injection unit (according to EUROMAP):, 100 www.arburg.com
275 V Installation dimensions 900 665 1782 2880 1) 3025 2) 2835 1) 2945 2) 167 1921 800 900 Support surface of table to mounting surface 1799 min. 900 max. 1050 Fixed mould mounting surface Horizontal version 800 3) 4) Electrical connection 655 679 983 1159 1) 1740 2) Cooling water connection Pneumatic connection 1) Injection unit 2) Injection unit 100 3) The control cabinet length and position of the electrical connection can vary due to optional equipment 4) Position of cooling water connections can vary due to optional equipment 2
Technical data 275 V Clamping unit with clamping force max. kn 0 0 0 0 0 275 V 250 0 0 0 0 0 Version Opening force stroke max. kn mm Standard 100 225 Rotary table 100 225 Shuttle table 100 225 Mould height, fixed variable min. mm --- 150 --- 127 --- 122 Platen daylight fixed variable max. mm --- 375-475 --- 352-452 --- 347-447 Table diameter mm --- 750 --- Shuttle table stroke mm --- --- 500 Angle of rotation, left/right Rotation time for 180 min. s --- --- 180 1,7 --- --- Weight on rotary/shuttle table max. kg --- 120 120 Weight of movable mould half max. kg 110 110 110 Ejector force stroke max. kn mm 30 60 16 40 16 40 Dry cycle time EUROMAP ² min. s - mm 4,8-192 4,8-192 4,8-192 Injection unit with screw diameter mm 18 22 25 20 100 25 30 0 0 0 0 Effective screw length L/D 24,5 20 17,5 25 20 16,7 0 0 0 Screw stroke max. mm 90 100 0 Calculated stroke volume max. cm³ 23 34 44 31 49 71 0 0 0 Shot weight max. g PS 21 31 40 29 45 65 0 0 0 Material throughput max. kg/h PS 4,1 5,5 6,5 5,5 8 9,5 0 0 0 max. kg/h PA6.6 2,1 2,8 3,3 2,8 4 4,9 0 0 0 Injection pressure max. bar 2500 2000 1550 2500 2000 1390 0 0 0 Holding pressure max. bar 2500 2000 1550 2500 2000 1390 0 0 0 Injection flow ² max. cm³/s 42 62 80 40 62 90 0 0 0 Screw circumferential speed ² max. m/min 24 30 34 17 22 26 0 0 0 Screw torque max. Nm 90 110 120 120 150 180 0 0 0 Nozzle contact force retraction stroke max. kn mm 50 150 50 180 0 0 Heating capacity zones kw 4,1 4 4,9 5 0 0 Feed hopper l 8 8 0 Drive and connection with injection unit Standard 100 0 Rotary table 100 0 Shuttle table 100 0 Net weight of machine kg 1745 1765 0 2215 2235 0 2120 2 0 Sound press. level Insecurity ⁴ db(a) 67 3 67 3 67 3 Oil filling l 0 80 0 0 80 0 0 80 0 Drive power ² max. kw 0 7,5 0 0 7,5 0 0 7,5 0 Electrical connection ³ kw 14 15 0 14 15 0 14 15 0 Total A 0 50 0 0 50 0 0 50 0 Machine A 0 --- 0 0 --- 0 0 --- 0 Heating A 0 --- 0 0 --- 0 0 --- 0 Cooling water connection max. C min. Δp bar 25 1,5 DN 25 25 1,5 DN 25 25 1,5 DN 25 Machine type with EUROMAP size designation ¹ 275 V 250-100 0 0 Upon request: other machine types and mould installation heights, screws, drive powers, etc. All specifications relate to the basic machine version. Deviations are possible depending on variants, process settings and material type. Depending on the drive, certain combinations, e.g. max. injection pressure and max. injection flow may be mutually exclusive. 1) Clamping force (kn) - large injection unit = max. stroke volume (cm³) x max. injection pressure (kbar) 2) Specifications depend on the drive variant / drive configuration. 3) Specifications relate to 400 V/50 Hz. 4) Detailed info in the operating instr. [ ] Specifications apply to alternative equipment. 3
275 V Mould installation dimensions Ejector bolt X without coupling element with coupling element Coupling element 53 15 B 108-5 A Y 103 X R 260 Stroke max. 225 max. 375-475 Stroke max. 60 103 Mounting surface, fixed mould mounting platen Ø28 Stroke max. 60 95 Mounting surface, fixed mould mounting platen Ø13,5 Ø18,5 8,5 18 26 Cut-out in mould (if required) Y Ø50 (variable) a (set-up in accordance with mould parting line) Horizontal version splatter guard 60 20 max.15 Bore in mould (if required) Ø50 Ø80 b Ø110 a c 182 Bracket for parting line injection Injection with positions hydraulic nozzle for Injection unit 100 100 a min. 80 80 a max. 150 150 b min. 50 50 c min. 71 37 51 4
Mould installation dimensions 275 V Fixed mould mounting platen A 250 Ø1 Ø110 H7 rear safety enclosure 100 Ø 10H8-13 deep Ø14 254 362 252 150 M12-24 deep Ø 10H8-13 deep 350 Moving mould mounting platen B 404 Ø110 H7 162 254 324 275 5
275 V Rotary table installation dimensions BWS 923 2880 1) 2835 1) 766 1866 1816 3025 2) 2945 2) Mounting surface rotary table 418 2318 1200 Horizontal version 923 (1866) 1200 3) 1000 Mounting surface rotary table 4) Electrical connection 679 BWS Cooling water connection 655 1595 1) 1740 2) 1) Injection unit 2) Injection unit 100 3) The control cabinet length and position of the electrical connection can vary due to optional equipment 4) Position of cooling water connections can vary due to optional equipment BWS - NCG - Non-contacting guard (photoelectric safety barrier) 6
Mould installation dimensions for rotary table 275 V Ejector bolt (for gentle ejection) min.145 / max. 235 (entsprechend der Werkzeugtrennung einstellen)* 53 15 B A 108-5 103 R 260 max. 352-452 19,5+0,1 Ø18 Mould Mounting surface Rotary table *(Observe maximum height of mould parting line with ejector stroke and height of sprue in case of vertical injection unit) Stroke max. 225 Mould mounting platen rotary table A Useable mounting surface 350 129 rear safety enclosure Ø 750 746 Moving mould mounting platen B 602 492 404 Ø 750 Ø 480 Couplings Cooling circuits M12-24 deep for installing top mould platen Ø 110 H7 Ø14 162 254 324 BWS M8-14 deep Ø 20 for hydraulic ejector max. R 372 Ø 1 250 275 Ø10H8-13 deep 7
275 V Mould installation dimensions for rotary table Horizontal version Bracket for parting line injection 60 20 Injection with positions hydraulic nozzle for Injection unit Ø50 (variable) a (set-up in accordance with mould parting line) Bore in mould (if required) Ø80 b 100 100 a min. 80 80 a max. 150 150 a b min. 50 50 c min. 71 37 51 c 8
Overall dimensions - shuttle table 275 V 2880 1) 3025 2) 2835 1) 2945 2) 1800 1785 BWS 928 Mounting surface shuttle table 174 800 1928 Horizontal version 928 1805 Mounting surface shuttle table 800 3) 4) BWS Electrical connection 1960 Cooling water connection Pneumatic connection 1595 1) 1740 2) 1) Injection unit 2) Injection unit 100 3) The control cabinet length and position of the electrical connection can vary due to optional equipment 4) Position of cooling water connections can vary due to optional equipment BWS - NCG - Non-contacting guard (photoelectric safety barrier) 9
275 V Mould installation dimensions - shuttle table (228) Ejector bolt (for gentle ejection) 28 Height, sliding platen to mounting surface 53 15 A B 108-5 103 R 260 Stroke max. 347-447 19,5+0,1 Mould Mounting surface Shutter table Ø18 44 18 Mould mounting platen for shuttle table A 420 420 362 242 180 Distance from sliding platen to bar 2 Height, sliding platen 26 BWS Ø110H7 350 350 404 Ø110 H7 162 254 324 Stroke max. 225 Useable mounting surface Stroke 500 Stroke 500 rear safety enclosure Ø20 for hydraulic ejector M12-18 deep Ø20 for hydraulic ejector Moving mould mounting platen B Ø10H8-14 deep Ø1 250 275 M12-24 deep Ø14 10
Mould installation dimensions - shuttle table 275 V Horizontal version Bracket for parting line injection (variable) a (set in accordance with mould parting line)splatter guard splatter guard 182 Bore in mould (if required) 60 20 Ø50 Ø80 b Injection with positions hydraulic nozzle for Injection unit 100 100 a min. 80 80 a max. 150 150 a b min. 50 50 c c min. 71 37 51 11
275 V Shot weights Theoretical shot weights for the most important injection moulding materials Injection units according to EUROMAP Screw diameter mm Polystyrene max. g PS Styrene heteropolymerizates max. g SB max. g SAN, ABS 1) Cellulose acetate max. g CA 1) Celluloseacetobutyrate max. g CAB 1) Polymethyl methacrylate max. g PMMA Polyphenylene ether, mod. max. g PPE Polycarbonate max. g PC Polysulphone max. g PSU Polyamides max. g PA 6.6 PA 6 1) max. g PA 6.10 PA 11 1) Polyoximethylene (Polyacetal) max. g POM Polyethylene terephthalate max. g PET Polyethylene max. g PE-LD max. g PE-HD Polypropylene max. g PP Fluorpolymerides max. g FEP, PFA, PCTFE 1) max. g ETFE Polyvinyl chloride max. g PVC-U max. g PVC-P 1) 18 22 25 21 31 40 20 31 39 20 30 39 24 35 45 22 33 42 22 32 42 19 29 37 22 33 42 23 34 44 21 31 40 19 29 37 26 39 50 25 37 48 16 24 30 16 24 31 17 25 32 33 50 65 29 44 57 25 38 49 23 35 45 100 20 25 30 29 45 65 28 44 63 27 43 62 32 50 73 30 47 68 30 46 67 27 42 60 30 47 68 31 49 28 44 64 26 41 60 35 55 80 34 53 77 22 34 49 22 35 50 23 36 51 46 72 103 40 63 91 35 54 78 32 50 72 1) average value ARBURG GmbH + Co KG Arthur-Hehl-Strasse 72290 Lossburg Tel.: +49 7446 33-0 www.arburg.com contact@arburg.com With locations in Europe: Germany, Belgium, Denmark, France, United Kingdom, Italy, Netherlands, Austria, Poland, Switzerland, Slovakia, Spain, Czech Republic, Turkey, Hungary Asia: People s Republic of China, Indonesia, Malaysia, Singapore, Taiwan, Thailand, United Arab Emirates America: Brazil, Mexico, USA For more information, please go to www.arburg.com. 2018 ARBURG GmbH + Co KG The brochure is protected by copyright. Any utilisation, which is not expressly permitted under copyright legislation, requires the previous approval of ARBURG. All data and technical information have been compiled with great care. However we accept no responsibility for correctness. Individual illustrations and information may deviate from the actual delivery condition of the machine. The relevant valid operating instructions are applicable for the installation and operation of the machine. ARBURG GmbH + Co KG DIN EN ISO 9001 + 01 + 50001 certified 528895_EN_GB_032018 Subject to alterations