Sheet No.: 1.101.30 Rev. ate: January 2012 ONSTRUTION, PRTS N MTERILS P-SERIES TUTORS P Parts Materials Executions Nr. escription Qty. escription Specification Std S.S. Shaft SR 1 ody 1 luminium lloy GlSi10Mg, IN 1725/2 - - 6 2 Piston 2 luminium lloy GlSi 7Mg, IN 1725/2 - - - 3 End ap P 2 luminium lloy GlSi10Mg, IN 1725/2 - - 6 End ap PS 2 luminium lloy GlSi10Mg, IN 1725/2 - - 6 5 entral drive shaft 1 luminium lloy lznmgu1.5, IN 1725/1 1 6 Gear Rack 2 Steel 5, IN 17200 - - - 8 Spring 1 arbon Spring Steel lass, IN 17223 2 2 2 9 * earing ush 1 Nylatron GS P6.6 + MoS2 - - - 10 * earing ush 1 elrin POM - - - 1 * Guide band 2 PTFE, arbon filled PTFE + 25% - - - 15 * Guide band 2 PTFE, arbon filled PTFE + 25% - - - 16 * O-ring 2 Nitrile Rubber una N - - - 17 * O-ring 2 Nitrile Rubber una N - - - 18 * O-ring 1 Nitrile Rubber una N - - - 19 * O-ring 1 Nitrile Rubber una N - - - 20 * Spring lip 1 arbon Spring Steel k75, IN 17222 2 5 5 21 * Thrust asher 1 ZEEX 100 K - - - - 23 olt lloy Steel 12.9 IN 912 - - - 2 Endcap olt P 20 lloy Steel 8.8 IN 912 2 25 Endcap olt PS 20 lloy Steel 8.8 IN 912 2 26 * O-ring 2 Nitrile Rubber una N - - - 27 Threaded insert 20 Steel 9S MnPb28K 3 3 3 * Recommended spare parts (contained in Repair kit) OULE TING P SINGLE TING PS s 1 Hard anodised aluminium alloy: lznmgu1.5, IN 1725/1 2 eltatone oating 3 Zinc plated and passivated Stainless Steel ISI 30 Finish Standard : Polyester non-tgi based powder coating (see data sheet.20.01) SR : SR oating (see data sheet.20.02) 5 Stainless Steel, X35rM017 6 SR oating (see.20.02) 7 P000 has a stainless steel (ISI 30) locking ring between spring clip (20) and thrust washer (21) 8 P000 has in the springs a guiding bush (PV) opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.101.33 Rev. ate: January 2012 ONSTRUTION, PRTS N MTERILS E-SERIES TUTORS E Optional centre-plate s 1 Hard anodised aluminium alloy: lznmgu1.5, IN 1725/1 2 eltatone oating 3 nodised Zinc plated and passivated 5 SR oating (see.20.02) 6 Stainless Steel Sandvic 1802, SS2382 7 Stainless Steel X35rM017 8 No insert, adaptor square direct in pinion Parts Materials Executions Nr. escription Qty. escription Specification Std S.S. Shaft SR 1 ody 1 luminium lloy GlSi10Mg, IN 1725/2 - - 5 2 Piston 2 luminium lloy GlSi 7Mg, IN 1725/2 - - - 3 rive Shaft 1 luminium lloy lznmgu1.5, IN 1725/1 1 6 6 End ap E 2 luminium lloy GlSi9u3, IN 1725/2 - - 5 5 End ap ES 2 luminium lloy GlSi9u3, IN 1725/2 - - 5 6 Spring- inner 2 arbon Spring Steel lass, IN17223 2 2 2 7 Spring- mid 2 arbon Spring Steel lass, IN17223 2 2 2 8 Spring- outer 2 arbon Spring Steel lass, IN17223 2 2 2 9 Spring Holder 2 Steel RSt 1-03, IN 1623 3 3 3 10 * Guide and 1 Nylatron P6.6 + MoS2 - - - 11 * Guide and 2 PTFE, arbon filled PTFE + 25% - - - 12 * earing ush 1 Nylatron P6.6 + MoS2 - - - 20 * earing ush 1 elrin POM - - - 21 * O-ring 1 Nitrile Rubber una N - - - 22 * asher ES 2 Nylon P6 - - - 23 * asher E 2 Nylon P6 - - - 25 * O-ring 2 Nitrile Rubber una N - - - 26 * O-ring 2 Nitrile Rubber una N - - - 27 * asher 1 ZEEX 100 K - - - - 28 * O-ring 1 Nitrile Rubber una N - - - 29 * O-ring Nitrile Rubber una N - - - 30 * O-ring 2 Nitrile Rubber una N - - - 3 asher ES 2 Steel 35 3 3 3 35 * Spring lip 1 arbon Spring Steel 5, IN 17200 2 7 7 36 End ap olt E/ES 8 Stainless Steel ISI 30 - - - 37 Limit Stop olt ES 2 Stainless Steel ISI 30 - - - 38 Nut 2 Stainless Steel lsl 30 - - - 0 Limit Stop olt E 2 Stainless Steel ISI 30 - - - 1 Nut 2 Stainless Steel ISI 30 - - - 2 Nut over 2 Polyethylene PE - - - 3 * O-ring 2 Nitrile Rubber una N - - - Insert 1 luminium lloy lmgsi1 9 5 Threaded insert 8 Steel 9S MnPb28K 3 3 3 6 entre-plate 1 Nylon, Glassfilled P6 + 25% Glass - - - * Recommended spare parts (contained in Repair kits) OULE TING E SINGLE TING ES Finish Standard : Polyester non-tgi based powder coating (see data sheet.20.01) SR : SR oating (see data sheet.20.02) opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.101.60 Rev. ate: January 2012 ONSTRUTION, PRTS N MTERILS S TUTOR S 1 2 7 11 3 9 5 6 12 10 8 13 1 Nr. escription Qty. Material Specification 1 ody S 1 luminium lloy GlSi10Mg, IN 1725/2-2 Piston S 2 luminium lloy GlSi 7Mg, IN 1725/2-3 rive Shaft S 1 luminium lloy lznmgu1.5, IN 1725/1 1 * Guide and S 1 Nylatron GS P6.6 + MoS2-5 am for stroke adj. S 1 Stainless Steel ISI 30-6 Shaftpin for stroke adj. S 1 hrome nickel steel 30rNiMo8-7 * asher 1 ZEEX 100 K - - 8 * asher 1 Nylon P6-9 * O-ring shaft top 1 Nitrile Rubber una N - 10 * O-ring limit stop bolt S 1 Nitrile Rubber una N - 11 irclip 1 arbon spring steel k75, IN17222 2 12 Limitstop bolt S 1 Stainless Steel ISI 30-13 Nut 1 Stainless Steel ISI 30-1 Nut over 1 Polyethylene PE - * Recommended spare parts (contained in Repair kits S) Finish Polyester non-tgi based powder coating (see data sheet.20.01) 1 Hard anodised 2 eltatone coating Remark This data sheet shows only the extra or specific parts of a S actuator. For all the other parts see data sheet 1.101.33 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.101.70 Rev. ate: January 2012 LO TEMPERTURE TUTOR SPEIFITIONS -0 / +80-0 F / +176 F Silicone MVQ 70 Sealings astrol Optitemp TT1 Low Temperature Grease escription double piston, rack and pinion pneumatic actuator incorporating a three point piston support system, anti-blowout spindle and with high duty synthetic bearings at all bearing points. This version is a standard aluminium actuator, but incorporating parts and materials suitable for low temperature operation. hen operating actuators in sub-zero temperatures (< 0 or < 32 F) care should be taken to counter the effects of freezing condensate inside the actuator. Specification Max. pressure : 8 bar (120 psi) Torque : Standard Media : ir or non corrosive gas Temperature : -0 to +80 (-0 F to +176 F) Finish : Polyester non-tgi based powder coating (see data sheet.20.01) Spare parts edicated low temperature spare parts are available for maintenance or make a standard actuator suitable for low temperature operation. Materials Part Material Specifications Remark Housing luminium lloy GlSi10Mg, IN 1725/2 luminium lloy lznmgu1.5, IN 1725/1 Hard anodised rive Shaft Steel (180 rotation) ETG100 or 2rMoV XM Zinc Plated type > P750 Stainless Steel Sandvic 1802, SS2382 or X35rM017 type > E950 Piston luminium lloy GlSi 7Mg, IN 1725/2 Sealings Silicone MVQ 70 O-rings -/- Grease astrol Optitemp TT1 -/- Shaft bearings Top : elrin POM ottom : Nylatron P6.6 + MoS2 Piston bearings PTFE 25% arbon filled ody bearings PTFE ( P series) 25% arbon filled Nylatron ( E series) P6.6 + MoS2 Shaft thrust washer ZEEX 100 K -/- End cap bolts Stainless Steel ( E series) ISI 30 2 lloy Steel ( P series) 8.8 IN 912 eltatone coating Springs arbon Spring Steel lass, IN17223 eltatone coating opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.101.71 Rev. ate: January 2012 HIGH TEMPERTURE TUTOR SPEIFITIONS -20 / +120 - F / +28 F Viton FPM Sealings astrol LMX Grease escription double piston, rack and pinion pneumatic actuator incorporating a three point piston support system, anti-blowout spindle and with high duty synthetic bearings at all bearing points. This version is a standard aluminium actuator, but incorporating parts and materials suitable for high temperature operation. Specification Max. pressure : 8 bar (120 psi) Torque : Standard Media : ir or non corrosive gas Temperature : -20 to +120 (- F to +28 F) Spare parts edicated high temperature spare parts are available for maintenance or make a standard actuator suitable for high temperature operation. Materials Part Material Specifications Remark Housing luminium lloy GlSi10Mg, IN 1725/2 luminium lloy lznmgu1.5, IN 1725/1 Hard anodised rive Shaft Steel (180 rotation) ETG100 or 2rMoV XM Zinc Plated type > P750 Stainless Steel Sandvic 1802, SS2382 or X35rM017 type > E950 Piston luminium lloy GlSi 7Mg, IN 1725/2 Sealings Viton FPM O-rings -/- Grease astrol LMX -/- Shaft bearings Top : elrin POM ottom : Nylatron P6.6 + MoS2 Piston bearings PTFE 25% arbon filled ody bearings PTFE ( P series) 25% arbon filled Nylatron ( E series) P6.6 + MoS2 Shaft thrust washer ZEEX 100 K -/- End cap bolts Stainless Steel ( E series) ISI 30 2 lloy Steel ( P series) 8.8 IN 912 eltatone coating Springs arbon Spring Steel lass, IN17223 eltatone coating opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.102 Rev. ate: January 2012 TEHNIL ETILS, STNR TUTOR E/P P-Series E-Series P = ouble acting E = ouble acting 11 djustable range* 91 Open 91.5-0.5 losed PS = Spring return ES = Spring return Specification Pressure range : ouble acting 0.2 to 8 bar : Spring return 6 to 8 bar, with max. spring set 3 to 8 bar, reduced spring quantity : 180 actuators 6 bar g maximum Torque : 1.6 to 955 Nm at 6 bar supply See torque data sheets 1.10.01 and 1.10.02 Operating media : ir, dry or lubricated and inert gasses : For sub-zero applications take appropriate measures Temperature : -20 to +80 Lubrication : Factory lubricated for the normal life of the actuator onstruction : Suitable for indoor and outdoor installation Finish : Polyester non-tgi based powder coating (see data sheet.20.01) Rotation ouble acting Spring return TUTOR TYPE E12 E25 E0 E65 E100 E150 E200 E350 E600 E950 E1600 P2500 P000 ore mm. 6 56 70 80 91 103 110 15 175 200 230 300 325 Stroke mm. 12.6 15.7 18.8 22 25.1 31. 37.7 37.7 50.3 62.8 56.5 81.7 eight: ouble acting kg. 0.6 1.3 1.8 2. 3.1.8 5.8 10. 19. 26. 2.7 56.8 86.6 Spring return kg. 0.7 1.7 2. 3.6.6 6.9 9.1 16.9 27.6 38.6 65.8 88.2 131.8 Operating time sec. 0. 0.5 0.7 1.1 1.2 1.8 2.3 3.6.5 5. 6.9 7 12 ir consumption at 1 atm (litres) : 91.5 (-0.5 to 91 ) : Standard counter clockwise with port "" pressurized (code, see data sheet 1.503 for other assembly codes) : lockwise fail action (code, see data sheet 1.50 for other assembly codes) Limit stops : Standard on E-Series. djustable range 91 /80 : Optional on P-Series. See data sheet 1.501.01 : For double stroke adjustment. See data sheet 1.501.05 European irectives PE : ll actuators are suitable for use with Group 2 gasses according to Pressure Equipment irective 97/23/E : Optional : actuators suitable for use with Group 1 gasses TEX : ll basic actuators are suitable for use in hazardous area's classified II 2 G, zones 1 or 2 (Gasses) and 21 or 22 (ust) RoHS : This product is only intended for use in large-scale fixed installations excluded from the scope of irective 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS 2). Russian pprovals El-O-Matic E and P series pneumatic actuators are available with the GOST-R and Rostechnadzor (RTN) approvals. 1. Operating time is average with actuator under load and solenoid valve fitted. 2. ir consumption is the actual free air volume at 1 atm. 3. Pressure is in barg. port stroke 0.1 0.1 0.2 0.3 0. 0.73 0.8 1.8 2.9.7 7.3 8 13.5 port stroke 0.1 0.1 0.2 0. 0.5 0.65 1 1.9 3.1.9 8.0 9.3 17.5 * only standard on E-Series actuators opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.102.10 Rev. ate: January 2012 -O-MTI SI PNEUMTI TUTOR ONFIGURTION E/P Single or ouble action ES or PS = Single acting, E or P = ouble acting ctuator size E-Series 0012 = E12 0025 = E25 000 = E0 0065 = E65 0100 = E100 0150 = E150 0200 = E200 0350 = E 350 0600 = E600 0950 = E950 1600 = E1600 P-Series 2500 = P2500 000 = P000 Valve flange Metric Metric UN/NPT Finish ISO 5211 IN 3337 ISO 5211 M = = U = Standard N = E = V = SR coating (2 + luminium pinion O = F = = SR coating (2 + Stainless Steel pinion (3 Limit stops 0 = No limit stops 1 = L1 One way limit stops 2 = ouble Stroke djustment Standard on P-Series Standard on E-Series Standard on S-Series ssembly code ode ction Rotation Mounting = Spring to close clock wise in line with pipeline = Spring to close clock wise across pipeline = Spring to open counter clock wise across pipeline = Spring to open counter clock wise in line with pipeline Spring set E-Series Spring set P-Series 00 = ouble acting actuator 00 = ouble acting actuator 01 = Springset 1 0 = Springset 0 = Springset 10 = Springset 10 02 = Springset 2 05 = Springset 5 06 = Springset 6 12 = Springset 12 03 = Springset 3 06 = Springset 6 08 = Springset 8 1 = Springset 1 Future expansion = Standard efault Insert Size (in mm.) (1 E12 E25 E0 E65 E100 E150 E200 E 350 E600 E950 E1600 P2500 P000 - ISO or UN 00 11 1 1 19 19 22 27 27 36 6 00 00 - IN 00 11 1 1 17 17 22 22 27 36 6 00 00 See following data sheets for more information 1.10.01 / 1.10.02 1.103.106 / 1.103.073 / 1.103.102 / 1.103.103 1.101.30 / 1.101.33 /.20.01 1.501.01/ 1.501.05 1.503/ 1.50 1.10.02 1.103.073 1.103.106 1.103.120 Visual Indication ode = isk K = Knob N = No visual indication ES 000.M 1 05.1 N 1 Temperature range 0 = Standard TS: 80 (176 F) -20 ( - F) 1 = High temp TS: 120 (28 F) -20 ( - F) 2 = Low temp TS: 80 (176 F) -0 (-0 F) (1 ctuators E12, P2500 and P000 have no inserts. They have have a inner square the shaft 180 actuators are not covered by this configuration matrix. (2 SR oating not possible in combination with ouble Stroke djustment limit stops (S series). (3 Stainless Steel Pinion not possible in combination with ouble Stroke djustment limit stops (S series). 1.101.70 / 1.101.71 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.103.073 Rev. ate: June 2010 IMENSION SHEET STNR TUTOR - IN E/P U1 E F E2 øq øp2 øp1 M1 M2 N ±0.5 Max. 5 øk Max. 5 øk1 O O E25-E950 97.2 T1 S1 S S 23.6 øp +0.5 0 R1 R R2 M5x8 G J 2 E-series øp +0.5 0 G1/" M1 2 I H øk 23.6 S M5x8 32 M6x12 P-series N ±0.5 M16x25 97.2 R P2500 R R2 im. in mm. ctuators E-series P-series E 12 E 25 E 0 E 65 E100 E150 E200 E 350 E600 E950 E1600 P2500 P000 159 180 199 221 25 283 305 387 2 516 378 502 SR 172 20 29 267 310 360 387 77 517 637 570 83 80 93 105 118 10 13 181 220 259 297 356 380 20 20 20 20 20 20 20 30 30 30 30 30 E 16 22 22 22 36 36 36 55 55 6 55 6 E2 23 30 30 30 5 5 5 65 65 75 65 80 F 10 1 1 1 19 19 19 36 36 36 36 36 G 12 12 12 12 12 12 12 10 10 10 10 10 H 7 86 98 108 121 128 173 207 231 265 350 380 I 6 53 58 63 70 73 95 113 126 12 183 200 J 32 3 0 5 59 51 73 8.5 105.5 120.5 178 190 K 2 33 33 38 55 55 55 68 75 95 85 120 K1 29 32 32 0 50 5 5 68 75 95 - - M1 3.5 3.5 3.5 3.5 50 50 50 52 6 82 66 77 M2 - - - 27-37 37 - - - - - N 3 3 3 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3 1.5 O max. 11.08 1.08 1.08 17.08 17.08 22.10 22.10 27.11 36.16 6.16 6.21 55.2 O min. 11.00 1.00 1.00 17.00 17.00 22.00 22.00 27.00 36.00 6.00 6.05 55.05 P 1.1 18.1 18.1 22.2 22.5 28.2 36.2 36.2 8.2 60.2 60.2 72.2 P1 1.1 18.1 21.1 23.1 28.5 32.1 32.1 36.5 8.5 60.5 - - P2 - - - 25.2-36.2 36.2 - - - - - Q 35 35 35 55 55 70 70 85 100 130 130 200 R 52 65 70 70 86 90 11 12 130 15 170 170 R1 50 50 50 60 60 60 60 90 90 125 160 160 R2 - - - - - - - - - 132-262 S 52 65 70 70 92 90 11 12 12 280 290 290 S1 100 100 100 100 100 100 100 170 170 210 25 25 T1 80 80 80 80 80 80 80 130 130 130 130 130 U1 30 30 30 30 30 30 30 30 30 30 30 30 F05 F05 F05 F07 F07 F10 F10 F12 F1 F16 F16 F25 V 50 50 50 70 70 102 102 125 10 165 165 25 M10 x 16 M10 x 16 M10 x 16 M8 x 13 M8 x13 M10 x 16 M10 x 16 M12 x 20 M16 x 25 M20 x 30 M20 x 30 M16 x 25 Optional dimensions K1' - 0 0 32 5 50 50 - - - - - Q' - 55 55 35 70 55 55 - - - - - F03 F07 F07 F05 F10 F07 F07 F10 F10 - - - V' 36 70 70 50 102 70 70 102 102 - - - ' M5 x 8 M8 x 13 M8 x 13 M6 x 10 M10x16 M8 x 13 M8 x 13 M10x 16 M10 x 16 - - - For E12 dimensions see data sheet 1.103.103 M16x25 Only E1600 P000 1. Flange and square drive to IN 3337 2. Top and solenoid flange to VI\VE 385 (NMUR) 3. For P-series actuators with limit stops see 1.501.01 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.103.102 Rev. ate: November 2009 IMENSION SHEET TUTOR ISO E12 (90 /180 ) J M5x8 G1/" 1 X 0 øp +0.5 T E F E2 L L1 2 U U1 G K1 K R 5 M N ±0.5 15 OULE TING TORQUE (E) I O H Y Pressure bar 3.5.5 5 5.5 6 7 Torque 90 /180 Nm 8.5 9.7 10.9 12.2 13. 1.6 17.1 SINGLE TING TORQUE (ES) ir stroke Pressure bar 5 6 Spring stroke Position - start end start end start end Torque 90 Nm 7.6.9 10 7.5 7.2.6 Torque 180 Nm 7.8 5 10. 7.6 7.1.5 im. in mm 90 180 E 103 155 ES 118 216 60 60 20 20 E 16 16 E2 23 23 F 10 10 G 12 12 H 60 60 I 33 33 J 21 21 K 12.7 12.7 K1 6. 6. L 25. 25. L1 50.8 50.8 M 16.5 16.5 N 1 1 O max. 9.1 9.1 O min. 9 9 P 12.1 12.1 R 0 0 R1 0 0 T 0 0 U 31 31 V 2 2 M6x8 M6x8 1 Mx7 Mx7 2 Mx7 Mx7 X G1/8" G1/8" Y M6x12 M6x12 : otted image represents optional NMUR solenoid interface block opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.103.103 Rev. ate: November 2009 IMENSION SHEET TUTOR IN E12 (90 /180 ) T 2 im. in mm 90 180 E 103 155 J M5x8 G1/" 1 X O E F E2 L L1 U U1 G K1 K R 5 M N ±0.5 15 OULE TING TORQUE (E) I H Y P +0.5 0 Pressure bar 3.5.5 5 5.5 6 7 Torque 90 /180 Nm 8.5 9.7 10.9 12.2 13. 1.6 17.1 SINGLE TING TORQUE (ES) ir stroke Pressure bar 5 6 Spring stroke Position - start end start end start end Torque 90 Nm 7.6.9 10 7.5 7.2.6 Torque 180 Nm 7.8 5 10. 7.6 7.1.5 : otted image represents optional NMUR solenoid interface block ES 118 216 60 60 20 20 E 16 16 E2 23 23 F 10 10 G 12 12 H 60 60 I 33 33 J 21 21 K 12.7 12.7 K1 6. 6. L 25. 25. L1 50.8 50.8 M 16.5 16.5 N 1 1 O max. 9.1 9.1 O min. 9 9 P 12.1 12.1 R 0 0 R1 0 0 T 0 0 U 31 31 V 2 2 M6x8 M6x8 1 Mx7 Mx7 2 Mx7 Mx7 X G1/8" G1/8" Y M6x12 M6x12 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.103.106 Rev. ate: November 2009 IMENSION SHEET STNR TUTOR - ISO E/P U1 M1 M2 N ±0.5 1 øp E25-E950 97.2 M16x25 T1 S1 E F E2 øp2 øp1 øk S S 23.6 Only E1600 1 M5x8 R1 E-series O R R2 G J M1 0 øp +0.5 1 G¼" 2 I H øk 23.6 S M5x8 M6x12 P000 32 P-series N ±0.5 O 97.2 R P2500 1 M16x25 R R2 im. in mm. ctuators E-series P-series E 12 E 25 E 0 E 65 E100 E150 E200 E 350 E600 E950 E1600 P2500 P000 159 180 199 221 25 283 305 387 2 516 378 502 SR 172 20 29 267 310 360 387 77 517 637 570 83 80 93 105 118 10 13 181 220 259 297 356 380 20 20 20 20 20 20 20 30 30 30 30 30 E 16 22 22 22 36 36 36 55 55 6 55 6 E2 23 30 30 30 5 5 5 65 65 75 65 80 F 10 1 1 1 19 19 19 36 36 36 36 36 G 12 12 12 12 12 12 12 10 10 10 10 10 H 7 86 98 108 121 128 173 207 231 265 350 380 I 6 53 58 63 70 73 95 113 126 12 183 200 J 32 3 0 5 59 51 73 8.5 105.5 120.5 178 190 K 2 33 33 38 55 55 55 68 75 95 85 120 M1 3.5 3.5 3.5 3.5 50 50 50 52 6 82 66 77 M2 - - - 27-37 37 - - - - - N 1 1 1 1.5 1 1.5 1.5 1.5 1.5 1.5 3 1.5 O max. 11.08 1.08 1.08 19.08 19.08 22.10 27.11 27.11 36.16 6.16 6.21 55.2 O min. 11.00 1.00 1.00 19.00 19.00 22.00 27.00 27.00 36.00 6.00 6.00 55.00 P 1.1 18.1 18.1 25.2 25.5 28.2 36.2 36.2 8.2 60.2 60.2 72.2 P1 1.1 18.1 21.1 23.1 28.5 32.1 32.1 36.5 8.5 60.5 - - P2 - - - 25.2-36.2 36.2 - - - - - R 52 65 70 70 86 90 11 12 130 15 170 170 R1 50 50 50 60 60 60 60 90 90 125 160 160 R2 - - - - - - - - - 132-262 S 52 65 70 70 92 90 11 12 12 280 290 290 S1 100 100 100 100 100 100 100 170 170 210 25 25 T - - - - - - - - - 23.6 23.6 - T1 80 80 80 80 80 80 80 130 130 130 130 130 U - - - - - - - - - 97.2 97.2 - U1 30 30 30 30 30 30 30 30 30 30 30 30 F03 F05 F05 F05 F07 F07 F07 F10 F10 F16 F16 F16 V 36 50 50 50 70 70 70 102 102 165 165 165 M5 x 8 M6 x 10 M6 x 10 M6 x 10 M8 x 13 M8 x 13 M8 x 13 M10 x M10 x M20 x M20 x M20 x 16 16 30 30 30 F05 F07 F07 F07 F10 F10 F10 F12 F1 - - F25 V1 50 70 70 70 102 102 102 125 10 - - 25 For E12 dimensions see data sheet 1.103.102 1 M6 x 10 M8 x 13 M8 x 13 M8 x 13 M10 x 16 1. Flange and square drive to ISO 5211 2. Top and solenoid flange to VI/VE 385 (NMUR) 3. For P-series actuators with limit stops see 1.501.01 M10 x 16 M10 x 16 M12 x 20 M16 x 25 - - M16 x 25 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.103.200 Rev. ate: January 2012 RIVE INSERTS FOR -O-MTI TUTORS E Standard available insert shapes sq Max. Optional available insert shapes Max. M1 M2 Insert mounting acc. ISO 5211 Ø P2 Ø P1 M1 M2 Insert mounting acc. IN 3337 Ø P2 Ø P1 escription Most of the El-O-Matic actuators are fitted with drive inserts. This enables actuators to be directly mounted onto suitable valves and eliminates the need for a bracket and coupling type mounting kit. The use of direct mounts significantly cuts the cost of the valve/actuator assembly. Standard actuators are fitted with square drive inserts in accordance with ISO 5211 (or IN 3337), but a wide variety of other inserts are also available. Special inserts may have oversize or undersize squares, double- and shaft key way forms. rive inserts can be supplied on factory built actuators or as loose items and are easily replaceable at distributor or end user level. here direct mounts are not possible, for instance on valves with exposed grand packing, the use of inserts often simplifies the design of the mounting kit. im. in mm Max. entering plate Inserts with inner-square-dimensions per actuator type E25 E0 / E65 E100 E150 E200 E350 E600 E950 E1600 Standard inserts dimensions ISO5211 11 1 19 19 22 27 27 36 6 IN3337 11 1 17 17 22 22 27 36 6 Optional insert dimensions 9 10 12 1 1 1 1 22-10 12 1 16 16 16 16 - - - - 16 22 17 17 17 - - - - - 2 19 19 19 - - - - - 27 2 2 2 - - Maximum insert dimensions M1 3.5 3.5 3.5 50 50 50 52 6 82 M2 - - 27-37 37 - - - P1 1.1 18.1 23.1 28.5 32.1 32.1 36.5 8.5 60.5 P2 - - 25.2-36.2 36.2 - - - Material : luminium alloy Finish : nodised The following actuator types do not have inserts. - E12, - P2500 and P000-180 actuators These actuators have inner square directly in the bottom of the pinion. See the following data sheets for more information : E12 ISO5211 1.103.102 IN 3337 1.103.103 P2500/P000 IN 3337 1.103.073 ISO 5211 1.103.106 180 IN 3337 1.203.011 ISO 5211 1.203.021 Sq max. 11 16 19 27 27 27 27 36 6 max. 13.8 21 23.6 33.6 33.6 33.6 33.6 5 60 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.10.01 Rev. ate: November 2009 OULE TING TUTOR TORQUE (Nm.) 90 OULE TING TORQUE Start End Torque Rotation -0.5 LOSE 91.5 ctuator Torque in Nm Supply Pressure (bar) Type Size 2 3 3.5.5 5 5.5 6 6.5 7 8 E 12.8 7.3 8.5 9.7 11.0 12.2 13. 1.6 15.9 17.1 19.6 E 25 9 13 16 18 20 23 25 27 29 32 36 E 0 17 25 29 3 38 2 7 51 55 59 68 E 65 25 38 5 51 58 6 71 77 8 90 10 E 100 38 57 66 76 86 95 105 115 12 13 153 E 150 60 91 106 122 137 153 168 183 199 21 25 E 200 82 12 16 167 188 209 230 251 272 293 335 E 350 13 216 253 290 326 363 00 36 73 510 583 E 600 23 368 30 92 55 617 679 71 80 866 991 E 950 363 59 62 735 828 921 101 1107 1200 1293 179 E 1600 600 907 1061 121 1368 1522 1676 1829 1983 2137 2 P 2500 958 19 169 190 2186 231 2677 2922 3168 313 390 P 000 1623 256 2872 3289 3705 121 537 95 5370 5786 6619 1. Emerson recommends that the valve manufacturer supply the maximum required torque values (Including any adjustments or suggested safety factors for valve service conditions or application). dditionally, the valve manufacturer must identify at which position(s) and direction(s) of rotation (ounter lock ise or lock ise) these maximum requirements occur. 2. If in doubt, or you require any assistance with sizing actuators, do not hesitate to contact your nearest Emerson's Valve utomation ivision representative. 3 Pressure on port "" opens the actuator* The actuator is shown in closed position* (* code, data sheet 1.503) 91 OPEN opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.10.02 Rev. ate: November 2009 SPRING RETURN TUTOR TORQUE (Nm.) 90 Start Torque Springset nr. ct. Type PS 2500 PS 000 E 91 OPEN SINGLE TING TORQUE IR STROKE Rotation ounter lockwise 91.5 End E Start F SPRING STROKE Rotation lockwise -0.5 LOSE F End 1. Emerson recommends that the valve manufacturer supply the maximum required torque values (Including any adjustments or suggested safety factors for valve service conditions or application). dditionally, the valve manufacturer must identify at which position(s) and direction(s) of rotation (ounter lock ise or lock ise) these maximum requirements occur. 2. If in doubt, or you require any assistance with sizing actuators, do not hesitate to contact your nearest Emerson's Valve utomation ivision representative. 3 Pressure on port "" opens the actuator* The actuator is shown in closed position* (* code, data sheet 1.50) ir Stroke (Nm) Spring SUPPLY PRESSURE Stroke 3.0 barg 3.5 barg.0 barg.5 barg 5.0 barg 5.5 barg 6.0 barg 7.0 barg (Nm) E F 6 896 602 112 88 1387 1093 1633 1339 1879 1585 212 1830 2370 2076 2861 2567 792 97 8 712 320 958 566 1203 811 19 1057 169 1302 190 158 2186 179 2677 2285 1056 663 10 - - 77 28 1019 529 1265 775 1510 1020 1756 1266 2001 1511 292 2002 1321 829 12 - - - - 835 27 1081 92 1326 738 1572 98 1817 1229 2308 1720 1585 995 1 - - - - - - - - 112 56 1387 701 1633 97 212 138 189 1160 6 152 1028 190 1 2356 1860 2772 2276 3189 2693 3605 3109 021 3525 85 358 1337 839 8 1213 551 1629 968 205 138 262 1800 2878 2216 329 2633 3710 309 53 3882 1783 1119 10 - - 1318 91 173 908 2151 132 2567 170 2983 2157 300 2573 232 305 2229 1399 12 - - - - 12 31 180 88 2256 126 2672 1680 3089 2097 3921 2929 267 1679 1 - - - - - - - - 195 788 2362 120 2778 1620 3610 253 3120 1958 Springset ir Stroke (Nm) Spring nr. SUPPLY PRESSURE Stroke ct. 3.0 barg 3.5 barg.0 barg.5 barg 5.0 barg 5.5 barg 6.0 barg 7.0 barg (Nm) Type E F ES 12 2 - - 3.8 1.0 5.1 2.3 6. 3.6 7.7.9 9.0 6.2 10.3 7.5 12.9 10.1 7.2.6 ES 25 ES 0 ES 65 ES 100 ES 150 ES 200 ES 350 ES 600 ES 950 ES 1600 2 3 5 6 9 6 12 9 1 11 16 13 19 16 21 18 2 21 29 25 7 7 2 9 5 12 7 1 9 16 12 19 1 21 17 26 21 11 7 - - - - 9 3 11 5 1 8 16 10 19 13 23 17 1 9 - - - - - - - - 11 1 6 16 8 21 13 18 11 - - - - - - - - - - - - 1 18 9 21 13 2 17 12 22 16 26 21 31 25 35 30 0 3 39 53 8 13 8 3 12 17 8 22 13 26 18 31 22 35 27 0 31 9 0 20 12 - - - - 17 5 21 10 26 1 30 19 35 23 33 26 17 5 - - - - - - - - 21 7 26 11 30 16 39 25 33 21 6 - - - - - - - - - - - - 25 8 3 17 0 25 2 26 17 32 23 39 30 6 37 53 60 51 67 58 81 72 21 13 3 18 5 25 11 32 18 39 25 6 32 52 39 59 6 73 60 32 20 - - - - 2 6 31 13 38 20 5 27 52 3 66 8 2 26 5 - - - - - - - - 30 8 37 15 22 58 36 53 33 6 - - - - - - - - - - - - 37 10 50 23 63 0 2 39 27 9 37 60 7 70 57 80 67 90 78 100 88 121 108 29 18 3 29 10 39 20 9 30 59 1 70 51 80 61 90 71 110 92 27 - - - - 39 1 9 2 59 3 69 80 5 100 75 58 37 5 - - - - - - - - 9 17 59 27 69 38 89 58 73 6 6 - - - - - - - - - - - - 59 21 79 1 88 55 2 63 1 79 58 95 7 112 90 128 107 1 123 161 139 193 172 8 29 3 6 1 62 30 79 7 95 63 111 79 128 96 1 112 177 15 72 - - - - 62 19 78 36 95 52 111 68 127 85 160 117 95 58 5 - - - - - - - - 78 2 9 1 110 57 13 90 119 73 6 - - - - - - - - - - - - 9 30 126 62 13 88 2 85 57 107 79 130 101 152 12 17 16 197 169 219 191 26 236 65 1 3 62 19 8 2 106 6 129 86 151 109 173 131 196 153 20 198 98 61 - - - - 83 26 105 9 127 71 150 93 172 116 217 160 131 82 5 - - - - - - - - 10 33 126 56 19 78 193 123 16 102 6 - - - - - - - - - - - - 125 1 170 85 196 123 2 1 96 183 135 221 17 260 213 299 252 338 290 377 329 5 07 116 7 3 101 30 10 68 179 107 217 16 256 185 295 22 33 263 12 30 17 112 - - - - 136 1 175 80 21 118 252 157 291 196 369 27 232 19 5 - - - - - - - - 171 52 210 91 29 130 326 207 289 186 6 - - - - - - - - - - - - 206 63 283 11 37 223 2 29 166 315 232 381 298 7 36 513 30 579 96 65 562 777 69 195 122 3 179 5 25 120 311 186 377 252 3 318 509 38 575 50 707 582 292 183 - - - - 20 7 306 10 372 206 38 272 50 338 636 70 389 25 5 - - - - - - - - 302 9 368 160 3 226 566 358 87 306 6 - - - - - - - - - - - - 36 11 96 26 58 367 2 375 29 7 37 572 6 671 5 769 63 868 71 966 80 1163 1037 290 179 3 272 82 371 181 69 279 568 378 666 76 765 575 863 673 1060 870 3 269 - - - - 366 113 65 211 563 310 662 08 760 507 957 70 579 359 5 - - - - - - - - 60 13 559 22 657 30 85 537 72 8 6 - - - - - - - - - - - - 55 17 751 371 869 538 2 617 16 780 579 93 72 1106 905 1269 1068 132 1231 159 139 1920 1719 7 299 3 5 1 608 307 771 70 93 633 1097 796 1260 959 123 1121 178 17 711 9 - - - - 599 198 762 361 925 523 1088 686 1251 89 1577 1175 97 598 5 - - - - - - - - 753 251 916 1 1079 577 105 903 118 78 6 - - - - - - - - - - - - 907 305 1233 630 121 897 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.203.011 Rev. ate: November 2009 IMENSION SHEET STNR 180 TUTOR 180 P60 - P750 G1/" M6x12 M1 M5x8 32 2 2 I H K M5x8 N ±0.5 J 3 R2 1 R U1 T1 S1 E1 F E2 S 1 M5x8 R1 2 O U G im. TUTOR TYPE in mm. E12 P60 P150 P280 P500 P750 P1100 P2500 P000 233 295 35 1 7 502 633 752 SR 256 332 3 97 553 61 817 1091 101 135 160 190 23 27 356 380 20 20 20 30 30 30 30 30 E1 16 22 26 36 36 5 55 6 E2 23 30 35 5 5 55 65 80 F 10 1 1 19 19 30 36 36 G 12 12 12 19 19 10 10 10 H 101 138 168 192 239 250 3 372 I 58 75 89 109 13 135 183 200 J 3 53 69 95 116 125 178 190 K 28 38 8 56 56 75 85 120 M1 27 27 31 38 38 51 66 77 N 1 1 1.5 1.5 2 2.5 3 1.5 O max. 1.11 17.11 22.13 27.13 27.13 36.16 6.16 55.19 O min. 1.00 17.00 22.00 27.00 27.00 36.00 6.00 55.00 P 18.1 25.2 28.2 36.2 36.2 8.2 60.2 72.2 R 60 80 101 111 10 10 170 170 R1 51 60 71 81 100 120 160 160 R2 70 100 - - - - - 262 S 111 130 11 161 210 210 290 290 S1 111 130 11 11 160 210 25 25 T - - - - - - 23.6 - For E12 dimensions see 1.103.102 T1 80 80 80 130 130 130 130 130 U - - - - - - 97.2 - U1 30 30 30 30 30 30 30 30 F05 F07 F07 F10 F10 F1 F16 F16 V 50 70 70 102 102 10 165 165 M6x9 M8x13 M8x13 M10x16 M10x16 M16x20 M20x30 M20x30 F07 F10 F10 F12 F12 - - F25 V1 70 102 102 125 125 - - 25 1 M8x13 M10x16 M10x16 M12x16 M12x16 - - M16x25 2 - - - - - - M16x25 - G1/2" 25. 3.9 25. 3.9 1 1 øp +0.5 0 T 2 x 8x1 1. Flange to ISO 5211, square drive to IN 3337 2. Top and Solenoid flange to VI/VE 385 (NMUR). P1100 P2500 and P000 have a non-nmur solenoid flange with 1/2" entries. 3. 180 actuators are standard equipped with "L1" limit stops. 120 or 135 rotation is possible with optional LF-option (See data sheet 1.501.01) P1100 - P000 P000 only opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.203.021 Rev. ate: November 2009 IMENSION SHEET STNR TUTOR IN 180 P60 - P750 M5x8 32 2 2 G1/" M6x12 I øq H M1 N ±0.5 Max. 5 K øk1 M5x8 25. G1/2" 3.9 P1100 - P000 25. 3.9 J 3 R2 1 R U1 1 øp +0.5 0 2 O T1 S1 E1 F E2 S 1 øp +0.5 0 T T S M5x8 R1 2 U U R P2500 O 2 G P60 - P1100 R R2 P000 im. In TUTOR TYPE mm E12 P60 P150 P280 P500 P750 P1100 P2500 P000 233 295 35 1 7 502 633 752 SR 256 332 3 97 553 61 817 1091 101 135 160 190 23 27 356 380 20 20 20 30 30 30 30 30 E1 16 22 26 36 36 5 55 6 E2 23 30 35 5 5 55 65 80 F 10 1 1 19 19 30 36 36 G 12 12 12 19 19 10 10 10 H 101 138 168 192 239 250 3 372 I 58 75 89 109 13 135 183 200 J 3 53 69 95 116 125 178 190 K 28 38 8 56 56 75 85 120 K1 32 50 5 68 68 95 95 - M1 27 27 31 38 38 51 66 77 N 1 1 1.5 1.5 2 2.5 3 1.5 O max. 1.11 17.11 22.13 27.13 27.13 36.16 6.16 55.19 O min. 1 17 22 27 27 36 6 55 P 18.1 25.2 28.2 36.2 36.2 8.2 60.2 72.2 Q 35 55 70 85 85 100 130 200 R 60 80 101 111 10 10 170 170 R1 51 60 71 81 100 120 160 160 R2 70 100 - - - - - 262 For E12 dimensions see 1.103.103 S 111 130 11 161 210 210 290 290 S1 111 130 11 11 160 210 25 25 T - - - - - - 23.6 - T1 80 80 80 130 130 130 130 130 U - - - - - - 97.2 - U1 30 30 30 30 30 30 30 30 F05 F07 F10 F12 F12 F1 F16 F25 V 50 70 102 125 125 10 165 25 M6x9 M8x13 M10x16 M12x16 M12x16 M16x20 M20x30 M16x25 2 - - - - - - M16x25 - Optional dimensions F07 F10 F07 F10 F10 - - - K1' 0 5 50 - - - - - Q' 55 70 55 - - - - - V1 70 102 70 102 102 - - - 1 M8x13 M10x16 M8x13 M10x16 M10x16 - - - 1. Flange to ISO 5211, square drive to IN 3337 2. Top and Solenoid flange to VI/VE 385 (NMUR). P1100 P2500 and P000 have a non-nmur solenoid flange with 1/2" entries. 3. 180 actuators are standard equipped with "L1" limit stops. 120 or 135 rotation is possible with optional LF-option (See data sheet 1.501.01). enterplate: a P2500 and P000 have center ring. opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.20.01 Rev. ate: November 2009 180 OULE TING TUTOR TORQUE (Nm.) 180 STRT TORQUE ROTTION EN ctuator type Torque in Nm Supply Pressure (bar) 2 3.5 5 5.5 6 E 12.8 7.3 9.7 10.9 12.2 13. 1.6 P 60 11 17 23 26 29 32 35 P 150 29 3 58 65 73 80 87 P 280 5 81 109 123 137 150 16 P 500 95 1 193 217 22 266 290 P 750 12 21 287 323 359 395 32 P 1100 209 316 23 76 530 583 637 P 2500 81 728 97 1098 1221 13 168 P 000 812 1228 165 1853 2061 2269 277 182 1. Emerson recommends that the valve manufacturer supply the maximum required torque values (Including any adjustments or suggested safety factors for valve service conditions or application). dditionally, the valve manufacturer must identify at which position(s) and direction(s) of rotation (ounter lock ise or lock ise) these maximum requirements occur. 2. If in doubt, or you require any assistance with sizing actuators, do not hesitate to contact your nearest Emerson's Valve utomation ivision representative. 3. Pressure on port "" opens the actuator*. The actuator is shown in closed position* 5. o not exceed the maximum supply pressure of 6 bar. (*code, data sheet 1.503) 181-1 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.20.02 Rev. ate: November 2009 180 SPRING RETURN TUTOR TORQUE (Nm.) 180 Start Torque E 181 IR STROKE Rotation ounter lockwise End 182 E Start SPRING STROKE Rotation lockwise 1. Emerson recommends that the valve manufacturer supply the maximum required torque values (Including any adjustments or suggested safety factors for valve service conditions or application). dditionally, the valve manufacturer must identify at which position(s) and direction(s) of rotation (ounter lock ise or lock ise) these maximum requirements occur. 2. If in doubt, or you require any assistance with sizing actuators, do not hesitate to contact your nearest Emerson's Valve utomation ivision representative. 3. Pressure on port "" opens the actuator*. The actuator is shown in closed position* 5. o not exceed the maximum supply pressure of 6 bar. (*code, data sheet 1.50) F End F -1 Spring nr. ir Stroke (Nm) Spring SUPPLY PRESSURE Stroke ctuator 3 3.5.5 5 5.5 6 (Nm) type E F ES 12 2 - - 3.8 1.1 5.2 2. 6.5 3.7 7.8 5.0 9.1 6.3 10. 7.6 7.1.5 PE 60 8 9 12 6 15 9 18 12 21 15 2 18 27 21 13 7 10 - - 10 3 13 6 16 9 19 12 22 15 25 18 16 9 12 - - - - 11 3 1 5 17 8 20 11 23 1 19 11 1 - - - - - - 12 2 15 5 18 8 21 11 22 12 PE 150 8 2 12 32 19 39 27 6 3 5 1 61 9 68 56 29 17 10 20 27 12 3 19 2 26 9 3 56 1 6 8 36 21 12 - - 22 30 11 37 19 26 52 33 59 0 25 1 - - - - 25 3 32 11 0 18 7 25 5 33 51 30 PE 280 8 3 9 57 23 71 37 85 51 99 65 112 78 126 92 67 3 10 - - 8 5 61 19 75 33 89 7 103 60 117 7 8 3 12 - - - - - - 66 15 80 29 93 2 107 56 101 51 1 - - - - - - - - 70 11 8 2 98 38 118 60 PE 500 8 - - 112 31 136 56 160 80 185 105 209 129 - - 128 51 10 - - - - 122 22 16 6 171 70 195 95 219 119 160 6 12 - - - - - - - - 156 36 181 61 205 85 192 77 1 - - - - - - - - - - 167 26 191 51 22 89 PE 750 8 13 29 170 66 206 102 22 138 279 175 - - - - 173 72 10 - - 150 20 186 56 222 92 259 128 295 165 331 201 216 91 12 - - - - - - 202 6 239 82 275 119 311 155 259 109 1 - - - - - - - - 218 36 255 72 291 109 302 127 PE1100 8 190 7 2 128 297 181 351 235 0 288 58 32 - - 226 113 10 - - 212 68 266 121 319 175 373 228 26 282 80 335 282 11 12 - - - - 23 61 288 11 31 168 395 221 8 275 339 170 1 - - - - - - 257 5 310 107 36 161 17 21 395 198 PS2500 8 356 160 79 283 602 06 72 528 87 651 970 77 1093 897 528 332 10 - - 387 12 510 265 632 387 755 510 878 633 1001 756 660 1 12 - - - - 17 123 50 26 663 369 786 92 909 615 792 97 1 - - - - - - 8 105 571 228 69 351 816 73 92 580 PS000 8 606 276 81 8 1023 692 1231 900 139 1108 167 1316 1855 152 891 560 10 - - 659 26 867 5 1075 662 1283 870 192 1078 1700 1286 111 699 12 - - - - 712 216 920 2 1128 632 1336 80 15 108 1337 839 1 - - - - - - 76 186 973 39 1181 602 1389 810 1560 979 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.501.01 Rev. ate: January 2012 -O-MTI TUTOR ITH ONE Y LIMIT STOPS L1/LF ode ode escription ctuators with one way adjustable limit stops are used where the maximum opening (or closing) position of the valve needs to be reduced. For instance to adjust the maximum capacity of a remote operated valve. lso actuators with 180 rotation are available with these stops. OULE TING SPRING RETURN Operation Stop screws are fitted to both endcaps and the screw length is such that adjustment is possible through the specified rotation of the actuator. The modified endcap is machined for -0.5 to +93 rotation for all P-Series models. Identification L1 is added to the basic part number i.e. P2500-L1 Specification Pressure : Up to 8 bar Operating media : ir, dry or lubricated or non-corrosive gas Torque (90 ) : ata sheet 1.10.01-1.10.0 (180 ) : ata sheet P-Series 1.20.01 and 1.20.02 Other dimensions : ata sheet 1.103.XXX (90 ) : ata sheet 1.203.011 (180 ) Temperature : -20 to +80 djustable range : 80-93 (90 ) or 160-186 (180 ) 97.2 23.6 165 M16x25 6 djustable position (see data sheet 1.503 or 1.50): ode Position Spring to: Valve open close Valve open close Valve closed open Valve closed open : o not adjust under pressure. im. TUTOR TYPE in mm. P2500 P000 580 708 795 1152 356 380 30 30 M20x30 25 165 M20x30 P2500 M16x25 55 Open 3 10 : 1) an be provided with extra long screws for full range adjustment (identification: P2500-LF) 2) This option in combination of a manual override gearbox is redundant djustable range 90 actuator djustable range 180 actuator losed -20 +6 Open losed opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.501.03 Rev. ate: November 2009 LIMIT STOP PLTE IMENSIONS LS 20 escription These limit stop plates are used when precise control is required for both end of stroke positions. It is possible to adjust 15 of both ends of the standard stroke. E onstruction The complete stop plate assembly may be added to the 90 P- series actuators. The assembly is normally sandwiched between the actuator and mounting surface of the valve or bracket. earing rings are used at both surfaces to provide a long life expectancy. Gmax. F ctuator base rive shaft Hmax. The unit is assembled with a drive adaptor which passes through the stop plate, into the square actuator and provides the coupling between the two components. This drive adaptor normally also accommodates the coupling of the valve stem. Identification "LS20" is added to the basic part number i.e. P2500-LS20 Other dimensions See data sheet 1.103.xxx Option Version for 180 or IN-standard actuator Flange according ISO 5211 O V over plate rive adaptor Housing limit stop am : over plate only in combination with P2500 Open +1 djustable range 90 actuators -15 +0.5 im. TUTOR TYPE in mm. P2500 P000 E 66 90 F 135 135 G 322 322 H 130 11 O 6 55 V 165 165 M20x30 M20x30 losed Flange according IN 3337 O opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.501.05 Rev. ate: November 2009 -O-MTI TUTOR ITH OULE STROKE JUSTMENT S Open stopscrew (2) 3 10 adjustable range 3 10 escription ctuators with double stroke adjustment are normally used for high performance butterfly valves where a fine adjustment is required for the closed position. In this version adjustment is provided at the end of the opening and closing stroke positions. S actuators may be double acting or spring return, though are normally used as spring return (fail close) actuators. Factory option: Fail to Open L L Y L L im. ctuator type in mm E25 E0 E65 E100 E150 E200 E350 E600 E950 E1600 159 180 199 221 25 283 305 390 0 520 SR 172 20 29 267 310 360 387 80 532 61 80 93 105 118 10 13 181 220 259 297 20 20 20 20 20 20 20 30 30 30 H 7 86 98 108 121 128 173 207 231 26 I 6 51 57.5 63 70 73 9.3 113 126 12 J1 28.3 35.1 0 3.7 8.7 53.9 72.5 88.8 102. 11. L 11.5 15.5 15.5 18.5 2.6 2.6 2.6 1.5 1.5 7.5 Y M6 M8 M8 M10 M10 M12 M12 M16 M16 M20 X 36 1.5 1.5 50.5 60 62.5 72.5 102 102 109.5 X max. 1.5 8.5 8.5 58.5 67 7 8 11.5 11.5 12 Y J 1 I X H 15 3 losed stopscrew (1) J 1 I X H 15 3 Operation The closed position is adjusted by means of the stop-screw (1) located in the actuator body and for the open position by the stop-screws (2) in the actuator end caps. Identification See data sheet 1.102.10. Specification Pressure : Up to 8 bar Operating media : ir, dry or lubricated or non corrosive gas Torque (90 ) : ata sheet 1.10.01 1.10.02 Rotation - Spring return : lock-wise on air failure. ouble acting : ounter clock-wise with port pressurised. Other dimensions : ata sheet 1.103.XXX Temperature : 20 to +80 djustable range : losed position (1), +3 /- 15 Open position (2), 80-93 1) an be provided with extra long end-cap stop screws for full range adjustment of the open position. 2) This S option is not required on actuators fitted with manual override gearboxes, as MO gearboxes already incorporate this function. Important 1) "Fail open" is factory option. 2) hen assembled for fail open operation (code ; see data sheet 1.50), both stop-screws (1) and (2) will adjust the closed position. There is no adjustment for the open position! Factory option: "Fail open" Stroke adjustment cam 1 2 opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.503 Rev. ate: November 2009 OULE TING TUTOR SSEMLY MOES E/P -port pressurized -port pressurized -port pressurized -port pressurized Pistons Shaft ll views are from above Pistons are shown in inner position STNR MOUNTING IN LINE MOUNTING ROSS LINE PISTONS TURNE 180 (from standard) SHFT TURNE 90 (from standard) MOUNTING ROSS LINE (OPTIONL L1/LF) LIMIT STOPS ILL JUST THE VLVE T OPEN POSITION (OPTIONL L1/LF) LIMIT STOPS ILL JUST THE VLVE T LOSE POSITION MOUNTING IN LINE SHFT TURNE 90 PISTONS TURNE 180 (from standard) -port pressurized -port pressurized -port pressurized -port pressurized opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)
Sheet No.: 1.50 Rev. ate: November 2009 SPRING RETURN TUTOR SSEMLY MOES E/P -port pressurized Spring stroke -port pressurized Spring stroke Springs Pistons Shaft ll views are from above Pistons are shown in inner position STNR MOUNTING IN LINE MOUNTING ROSS LINE PISTONS TURNE 180 (from standard) SPRING TO LOSE (ROTTION ) SPRING TO OPEN (ROTTION ) SHFT TURNE 90 (from standard) MOUNTING ROSS LINE MOUNTING IN LINE SHFT TURNE 90 PISTONS TURNE 180 (from standard) Spring stroke -port pressurized Spring stroke -port pressurized opyright Emerson. The information in this document is subject to change without notice. Updated data sheets can be obtained from our website www.emerson.com/el-o-matic or from your nearest ctuation Technologies enter: merica: +1 281 77 100 (fax +1 281 77 2809) Europe: +36 22 530 950 (fax +36 22 5 37 00) sia Pacific: +65 6777 8211 (fax +65 626 80 028) Middle East: +971 811 8100 (fax + 971 886 565)