Current Automation Catalogue Page 27
Visit our website for more indebt info on this product range Current Automation Catalogue Page 28
FlexMax MPPT Charge Controller FlexMax Extreme Flex-Ware FX - Inverter VFX -Inverter / Charger GFX -Inverter / Charger Current Automation Catalogue Page 29
Electronics Generators Systems OutBack FLEXmax MPPT Charge Controllers The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from OutBack Power Systems. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30% compared to non-mppt controllers. Thanks to active cooling and intelligent thermal management, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 40 C (104 F). A built-in, backlit 80 character display shows the current status and logged system performance data for the last 128 days at the touch of a button. The integrated OutBack network communications allows FLEXmax series Charge Controllers to be remotely programmed and monitored via a MATE system display and provides unrivaled complete system integration. The OutBack FLEXmax MPPT works on PWM as a low loss series controller OutBack FLEXmax 60 OutBack FLEXmax 80 Further OutBack products on p. 119 and p. 233 OutBack FLEXmax FM 60 Charge Controller 140 x 100 x 400 mm 5,4 kg FLEXMAX60 107699 60 A module current 12 60 VDC battery 150 VOC OutBack FLEXmax FM 80 Charge Controller 140 x 100 x 400 mm 5,6 kg FLEXMAX80 107700 80 A module current 12 60 VDC battery 150 VOC NEW Solar Charge Controller FLEXmax Extreme FLEXmax Extreme s advanced thermal engineering provides full power output from -20 to 45 C without requiring a cooling fan. And because a passively cooled unit can be sealed, circuit boards and other sensitive electronics can be fully protected from dust, dirt, insects and other external sources of contamination. Article Article No. Solar Charge Controller FLEXmax Extreme 321163 Battery current 80 A 12 60 VDC 150 VOC IP54 Current Automation Catalogue Page 30
T M OutBack FLEXpower ONE Systems The FLEXpower ONE System accommodates all of the essential protective devices in the smallest possible space at the lowest installed cost making it ideal for applications with modest power requirements such as cabins, chalets, homes, remote communication sites and back-up power systems. Utilizing an extremely compact design and an easy-to-install mounting bracket, the fully pre-wired and factory tested FLEXpower ONE System is designed for a quick installation. The FLEXpower ONE System is also equipped with battery and PV array breakers, a PV GFDI breaker, an Input-Output-Bypass Assembly, mounting locations for both AC GFCI Type B and EU Type F style outlets and additional AC breakers. FLEXpower ONE components carry all of the necessary ETL Certifications allowing for a code compliant installation that saves both time and money while still looking great. OutBack FLEXpower TWO Systems The FLEXpower TWO System accommodates all of the essential protective devices in an easy-to-install, fully pre-wired and factory tested dual inverter system. The FLEXpower TWO is ideal for applications with medium sized power requirements such as homes, light commercial or larger back-up power systems. Utilizing a compact design and an easy-to-install mounting plate, the FLEXpower TWO System can be mounted in either a horizontal or vertical orientation to allow installation in more space-limited locations and is designed for a quick installation, saving both time and money. Electronics Generators Systems OutBack Communication, p. 233 OutBack DC Monitor System, p. 233 OutBack Load Center, p. 233 OutBack FLEXpower ONE Systems OutBack FLEXpower ONE 327 x 500 x 849 mm 44,5 g 303478 3 kw 24 VDC 230 VAC 50 Hz FLEXpower ONE pre-wired AC and DC boxes with 230 VAC bypass, 250 ADC breaker, VFX 3024E, MATE2, HUB4, RTS, FLEXmax 80, FLEXnet DC and surge protector FLEXpower ONE 327 x 500 x 849 mm 44,5 g 303479 3 kw 48 VDC 230 VAC 50 Hz FLEXpower ONE pre-wired AC and DC boxes with 230 VAC bypass, 175 ADC breaker, VFX 3048E, MATE2, HUB4, RTS, FLEXmax 80, FLEXnet DC and surge protector OutBack FLEXpower TWO Systems OutBack FLEXpower TWO 1.181 x 514 x 330 mm 105 kg 320056 6 kw 24 VDC 230 VAC 50 Hz FLEXpower TWO pre-wired AC and DC boxes with 230 VAC bypass, two 175 ADC breakers, two VFX3048E, MATE2, HUB10 and RTS OutBack FLEXpower TWO 6 kva/48 V 1.181 x 514 x 330 mm 105 kg 320055 6 kw 48 VDC 230 VAC 50 Hz FLEXpower TWO pre-wired AC and DC boxes with 230 VAC bypass, two 250 ADC breakers, two VFX3024E, MATE2, HUB10 and RTS Current Automation Catalogue Page 31
OutBack FX Inverter OutBack FX Inverter/Charger Series The OutBack FX series is a modular building block sine wave inverter/charger that can be used for both small and large power systems. Each FX inverter/charger is a complete power conversion system - DC to AC inverter, battery charger and AC transfer switch. The FX series is also available in a version with 230 VAC, 50 hz output that can be connected in parallel (230 VAC) or in three phase (230Y400 VAC) configurations. Our unique sealed, gasketed die-cast aluminum chassis protects and keeps the power conversion components cool - without requiring outside air to be blown through the sensitive electronics. The FX can be used in high ambient applications up to 60 C with reduced output ratings. It is designed to operate as a coordinated system with the other OutBack products. OutBack FX 230 VAC Sinewave Inverter/Charger OutBack FX 2012ET 330 x 210 x 410 mm 28,4 kg 107301 2.000 VA 12 VDC 230 VAC 50 Hz 100 A charger sealed OutBack FX 2024ET 330 x 210 x 410 mm 28,4 kg FX2024-ET 107302 2.000 VA 24 VDC 230 VAC 50 Hz 55 A charger sealed OutBack FX 2348ET 330 x 210 x 410 mm 28,4 kg FX2348-ET 107303 2.300 VA 48 VDC 230 VAC 50 Hz 35 A charger sealed 115 VAC 60 HZ ON REQUEST Current Automation Catalogue Page 32
OutBack VFX Inverter/Charger Series The OutBack VFX series is a ventilated version of the original sealed FX series modular building block sine wave inverter/charger that can be used for both small and large power systems. By allowing cooler outside airflow through the internal electronics, more AC power is available. Additional VFX inverter/chargers can be connected at any time in either parallel (120 VAC), series (120/230 VAC), or three-phase (120/230 VAC) configurations. The VFX series is also available in a version with 230 VAC, 50 hz output that can be connected in parallel (230 VAC) or in three phase (230Y400 VAC) configurations. The VFX is designed to survive harsh environments around the world. The VFX can be used up to 60 C (reduced output ratings). It is designed to operate as a coordinated system with the other OutBack products. OutBack Communication, p. 233 OutBack DC Monitor System, p. 233 OutBack Load Center, p. 233 115 VAC 60 HZ ON REQUEST OutBack VFX 230 VAC Sinewave Inverter/Charger OutBack VFX 2612E 210 x 300 x 410 mm 27,7 kg VFX2612E-VENTED 107304 2600 2.600 VA 12 VDC 230 VAC 50 Hz 125 A charger vented OutBack VFX 3024E 210 x 300 x 410 mm 27,7 kg VFX3024E-VENTED 107305 3000 3.000 VA 24 VDC 230 VAC 50 Hz 85 A charger vented OutBack VFX 3048E 210 x 300 x 410 mm 27,7 kg 107306 VFX3048E-VENTED 3000 3.000 VA 48 VDC 230 VAC 50 Hz 45 A charger vented Current Automation Catalogue Page 33
OutBack GFX Inverter OutBack GFX Inverter/Charger Series The OutBack true sinewave GFX International Series is a competitive power solution designed for applications with lower power demands. Incorporating a DC-to-AC sinewave inverter, battery charger and AC transfer relay housed within a die-cast aluminum chassis, the International Series GFX Inverter/Chargers give you the ability to sell solar, wind or hydro power back to the utility grid while providing instantaneous back-up power in the event of a utility outage. The GFX Series built in transfer relay automatically disconnects your loads from the utility grid and powers them from the inverter in the event of an outage, allowing you to continue using your solar and battery back-up power, unlike traditional grid-tie systems. For areas that frequently experience power instability such as surges, spikes or brownouts, or where standard inverters have trouble syncing to the utility grid, the GFX International Series grid reconnect timers have been shortened to reduce overall sell-back downtime and improve system functionality. 60 HZ ON REQUEST OutBack Communication, p. 233 OutBack DC Monitor System, p. 233 OutBack Load Center, p. 233 OutBack GFX1312E 330 x 210 x 410 mm 22,5 kg 320081 1.300 VA 12 VDC 230 VAC 50 Hz 70 A charger OutBack GFX1424E 330 x 210 x 410 mm 22,5 kg GFX1312E-SEALED 320082 1.400 VA 24 VDC 230 VAC 50 Hz 40 A charger OutBack GFX1448E 330 x 210 x 410 mm 22,5 kg GFX1424E-SEALED 320083 1.400 VA 48 VDC 230 VAC 50 Hz 20 A charger GFX1448E-SEALED Current Automation Catalogue Page 34
NEW Inverter/Charger Radian GS7048E A fully-integrated solution compatible in both Off-Grid and grid-interactive applications, the Radian delivers 7.000 watts of pure sinewave continuous power with unsurpassed surge capacity. A true multi-country design featuring field-adjustable input/output voltage and frequency boundaries of 50/60Hz and 220-240V nominal, the GS7048E Radian is the latest expression of OutBack s on-going commitment to delivering clean, reliable power to homes, businesses and other facilities around the world. OutBack Communication, p. 233 OutBack DC Monitor System, p. 233 OutBack Load Center, p. 233 Inverter/Charger GS7048E 710 x 221 x 406 mm 56,7 kg 321164 7.000 VA 48 VDC 230 VAC 50 or 60 Hz remote temperature sensor and MATE3/HUB communications Current Automation Catalogue Page 35