Flexible Couplings RUPEX Series

Flexible Couplings RUPEX Series /2 Overview /2 Benefits /2 Application /2 Design /4 Function /4 Technical data /6 Type RWN hub material grey cast iron /6 Selection and ordering data / Type RWS hub material steel / Selection and ordering data /10 Type RFN with hub in grey cast iron /10 Selection and ordering data /11 Type RFS in steel /11 Selection and ordering data /12 Type RWB with brake disk to DIN 15432 /12 Selection and ordering data /14 Type RBS with brake disk to DIN 15432 Sizes 144 to 360 /14 Selection and ordering data /16 Type RBS with brake disk to DIN 15432 Sizes 400 to 1000 /16 Selection and ordering data /1 Type RWB with brake drum to DIN 15431 /1 Selection and ordering data /19 Type RBS with brake drum to DIN 15431 /19 Selection and ordering data /20 Spare and wear parts /20 Selection and ordering data Siemens MD 10.1 2015

FLENDER Standard Couplings General information Overview Coupling suitable for use in potentially explosive atmospheres. Complies with the current ATEX Directive for: II 2 G T4 / T5 / T6 D120 C -30 C T a +0 C / +50 C / +40 C IM2 RUPEX pin and bush couplings link machine shafts and compensate for shaft misalignment with weak restorative forces. The is conducted through elastomer s, so the coupling has typically flexible rubber properties. Thanks to their robust design, RUPEX couplings are also suitable for rough operating conditions. Benefits RUPEX couplings can also hold loads when overloaded and are therefore especially suitable for drives for special safety and reliability requirements. Torque shock loads and changing loads are no problem for robust, compact flexible RUPEX couplings. The steel variant is also especially suitable for high-speed drives. RUPEX couplings are fitted by putting together the coupling halves. Fitting with low torsional backlash is simplified by the barrel-shaped geometry of the s. RUPEX couplings require little maintenance. Only the elastomer s, as wear parts, need be replaced and the coupled machines need not be moved to do so. RUPEX couplings are suitable for reversing operation and horizontal and vertical fitting or fitting at any required angle. Application RUPEX couplings are available as a catalog standard in 26 sizes with a rated of between 200 Nm and 1300000 Nm. The coupling is suitable for use at ambient temperatures of between -30 C and +0 C. By using alternative elastomer s, the permissible ambient temperature range can be extended to between -50 C and +100 C. Frequently, the coupling is used to connect the gear shaft to the driven machine. In the case of drives without gear units, the coupling is particularly suitable for operation in rough conditions or heavy-duty drives with electric motor drive. entilator drives with high ventilator mass and drives in the cement industry are typical applications. Examples of particularly safety-relevant areas of application are cable railway drives, lifting gear for crane drives or escalator drives. Design A RUPEX coupling comprises two hub sections which are mounted on the machine shafts. The hub parts are connected positively by steel pins and elastomer s. The coupling can be fitted with add-on parts such as brake disks or brake drums. Up to size 360, the pins and s are fitted on one side. From size 400 up, the pins and s are fitted in the hubs on alternate sides. Materials Hubs Types RWN and RWB made of grey cast iron EN-GJL-250 Types RWS and RBS made of steel Flange Types RFN, RFS made of steel Pin Material steel 42CrMo4, surface fine-machined Buffer material Material/description Hardness Identification Ambient temperature NBR 0 Buffer black -30 C... +0 C standard type ShoreA NBR 0 ShoreA Buffer green -30 C... +0 C electrically insulating NBR soft NBR hard NR for low temperature HNBR high temperature 65 ShoreA Buffer black with green dot 90 ShoreA Buffer black with magenta dot 0 ShoreA Buffer black with white dot 0 ShoreA Buffer black with red dot -30 C... +0 C -30 C... +0 C -50 C... +50 C -10 C... +100 C Brake disks Type RWB made of EN-GJS-400 spheroidal graphite cast iron Type RBS made of steel Brake drums Type RWB made of EN-GJL-250 grey cast iron Type RBS made of steel /2 Siemens MD 10.1 2015

FLENDER Standard Couplings General information RUPEX pin and bush coupling types Type RWN RWS RWB RBS RFN RFS Description Coupling made of grey cast iron Coupling made of steel Coupling made of grey cast iron with brake drum or brake disk Coupling made of steel with brake drum or brake disk Coupling made of grey cast iron in flange-shaft variant Coupling made of steel in flange-shaft variant Further application-related coupling types are available. Dimension sheets for and information on these are available on request. RUPEX pin and bush coupling types on request Type Description All Coupling with axial backlash limitation All Coupling with pretensioned s All Coupling with lengthened pins and spacer sleeves RKS Coupling for engaging/disengaging during standstill RWNH, Coupling with extension piece RWSH RBM Coupling with lengthened pins for sliding rotor motors RAK Coupling combination RUPEX with ARPEX all-steel membrane coupling Types RWN/RWS One-sided arrangement of pins and s Types RWN/RWS Alternate-sided arrangement of pins and s G_MD10_EN_00091 up to size 360 from size 400 Types RWB/RBS with brake drum Types RWB/RBS with brake disk G_MD10_XX_00095 G_MD10_XX_00093 G_MD10_XX_00094 G_MD10_EN_00092 Types RFN, RFS Siemens MD 10.1 2015 /3

FLENDER Standard Couplings General information Function The motor is transmitted to the hub on the drive side via the shaft-hub connection, which is mostly designed as a keyway connection. With the aid of elastomer s mounted on steel pins, the is conducted to the hub on the output side. The hub on the output side further transmits the to the driven machine or a gear unit located in between. Because of the primarily compression-loaded s, the coupling has a progressive torsional stiffness. Technical data Power ratings Size Rated for type Torsional stiffness at 50 % capacity utilization for type Assembly 65 ShoreA 0 ShoreA 90 ShoreA 65 ShoreA 0 ShoreA 90 ShoreA Gap dimension Permitted shaft misalignment at speed n = 1500 rpm 1) Radial Angle T KN T KN T KN C Tdyn 50 % C Tdyn 50 % C Tdyn 50 % ΔS ΔK r ΔK w Nm Nm Nm knm/rad knm/rad knm/rad mm mm Degree 105 120 200 200 5 13 21 1.0 0.21 0.12 125 210 350 350 9 25 37 1.0 0.23 0.11 144 300 500 500 15 43 64 1.0 0.25 0.10 162 450 750 750 20 55 3 1.5 0.27 0.10 17 570 950 950 31 5 130 1.5 0.29 0.09 19 70 1300 1300 43 123 17 1.5 0.30 0.09 22 1300 2200 2200 65 14 270 1.5 0.34 0.09 252 1650 2750 2750 92 256 30 1.5 0.36 0.0 25 2600 4300 4300 141 390 560 1.5 0.40 0.0 320 3300 5500 5500 195 540 790 1.5 0.43 0.0 360 4700 700 700 276 610 940 1.5 0.4 0.0 400 7500 12500 12500 410 1130 1710 1.5 0.52 0.07 450 11000 1500 1500 570 1600 230 1.5 0.57 0.07 500 15000 25000 25000 60 2350 3600 1.5 0.62 0.07 560 23500 39000 39000 1130 3070 4700 2.0 0.6 0.07 630 31000 52000 52000 1640 4600 7400 2.0 0.75 0.07 710 50000 4000 4000 2560 7200 10900 2.0 0.4 0.07 00 66000 110000 110000 3900 10700 16700 2.0 0.93 0.07 900 90000 150000 150000 5200 14300 22500 2.5 1.03 0.07 1000 115000 195000 195000 7700 21300 33000 2.5 1.14 0.07 1120 160000 270000 270000 900 27300 44000 2.5 1.26 0.06 1250 205000 345000 345000 14000 39000 62000 2.5 1.39 0.06 1400 320000 530000 530000 2200 62000 97000 3.0 1.55 0.06 1600 450000 750000 750000 37000 103000 160000 3.0 1.76 0.06 100 55000 975000 975000 4000 133000 20000 4.0 1.96 0.06 2000 70000 1300000 1300000 73000 201000 314000 4.0 2.17 0.06 All article numbers listed below apply to standard s of NBR material in the 0 ShoreA variant. 1) The maximum speed of the respective type must be noted. For further information on permissible shaft misalignment, please see the operating instructions. /4 Siemens MD 10.1 2015

FLENDER Standard Couplings General information For maximum coupling : T Kmax =3.0 T KN For overload : T KOL =4 T KN For coupling fatigue : T KW =0.20 T KN For fitting, a maximum gap dimension of S max. = S + ΔS and a minimum gap dimension of S min. = S ΔS are permitted. Torsional stiffness and damping The values stated in the above table apply to a capacity utilization of 50 %, an excitation amplitude of 10 % T KN with the frequency 10 Hz and an ambient temperature of 20 C. Dynamic torsional stiffness is dependent on load and increases in proportion to capacity utilization. The following table shows the correction factors for different nominal loads. C Tdyn = C Tdyn 50 % FKC Permitted shaft misalignment The permitted shaft misalignment depends on the operating speed. As the speed increases, lower shaft misalignment values are permitted. The following table shows the correction factors for different speeds. The maximum speed for the respective coupling size and type must be observed! ΔK perm = ΔK 1500 FK Speed in rpm 500 1000 1500 3000 Correction factor FK 1.7 1.2 1.0 0.7 For fitting, a maximum gap dimension of Smax.=S+ΔS and a minimum gap dimension of Smin.= S ΔS are permitted. Shaft misalignments ΔK r and ΔK w may occur simultaneously. Correction factor FKC 65/0/90 ShoreA Capacity utilization T N / T KN 20 % 40 % 50 % 60 % 70 % 0 % 90 % 100 % 0.51 0.3 1.00 1.1 1.3 1.5 1.0 2.03 The damping coefficient is Ψ =1.4 Furthermore, torsional stiffness and damping depend on the ambient temperature and the frequency and amplitude of the torsional vibration excitation. More precise torsional stiffness and damping parameters on request. With elastic couplings the manufacturing process of the rubber elements and their aging primarily influence the rigidity value C Tdyn. For this reason calculation must be made with a tolerance for the dynamic rigidity of ± 20 %. The specified damping coefficient Ψ is a minimum value with the result that the damping performance of the coupling corresponds at least to the specified value. Siemens MD 10.1 2015 /5

FLENDER Standard Couplings Type RWN - hub material grey cast iron Selection and ordering data J1 J2 P U1 Part 1 U2 Part 2 ØND1 ØD1 ØD2 ØND2 NL1 LG S NL2 G_MD10_EN_00096 Size Rated Speed Dimensions in mm Mass Article No. Weight Bore with keyway to moment of DIN 65 inertia 0 ShoreA T KN n Kmax D1 D2 DA ND1 ND2 NL1/ S U1 U2 P LG J 1 J 2 section 3 m min. max. min. max. NL2 Nm rpm kgm 2 kgm 2 kg 105 1) 200 7000 32 3 105 53 59 45 3 13 12 30 93 0.001 0.001 2LC0130-1AA -0AA0 1.9 125 1) 350 6000 40 4 125 65 6 50 3 16 15 35 103 0.003 0.003 2LC0130-2AA -0AA0 3.2 144 500 5250 45 55 144 76 4 55 3 16 15 35 113 0.004 0.006 2LC0130-3AA -0AA0 4.5 162 750 4650 50 60 162 5 92 60 3.5 20 1 40 123.5 0.007 0.013 2LC0130-4AA -0AA0 6.7 17 950 4200 60 70 17 102 10 70 3.5 20 1 40 143.5 0.014 0.022 2LC0130-5AA -0AA0 9.7 19 1300 3750 70 0 19 120 12 0 3.5 20 1 40 163.5 0.022 0.030 2LC0130-6AA -0AA0 12.9 22 2200 3300 0 90 22 129 140 90 3.5 26 24 50 13.5 0.03 0.071 2LC0130-7AA -0AA0 19 252 2750 3000 90 100 252 150 160 100 3.5 26 24 50 203.5 0.07 0.12 2LC0130-AA -0AA0 26.3 25 4300 2650 4 100 4 110 25 164 175 110 4.5 32 30 60 224.5 0.13 0.22 2LC0131-0AA -0AA0 39 320 5500 2350 55 110 55 120 320 10 192 125 4.5 32 30 60 254.5 0.23 0.30 2LC0131-1AA -0AA0 53 360 700 2100 65 120 65 130 360 200 210 140 4.5 42 42 75 24.5 0.41 0.70 2LC0131-2AA -0AA0 7 400 12500 2050 75 140 75 140 400 230 230 160 4.5 42 42 75 324.5 0.7 0.7 2LC0131-3AA -0AA0 105 450 1500 100 5 160 5 160 450 260 260 10 5.5 52 52 90 365.5 1.7 1.7 2LC0131-4AA -0AA0 156 500 25000 1600 95 10 95 10 500 290 290 200 5.5 52 52 90 405.5 2. 2. 2LC0131-5AA -0AA0 200 560 39000 1450 100 140 100 140 560 250 250 220 6 6 6 120 446 4.6 4.6 2LC0131-6AA -0AA0 20 140 10 140 10 300 300 5 5 2LC0131-6AA -0AA0 290 10 200 10 200 320 320 5.1 5.1 2LC0131-6AA -0AA0 295 630 52000 120 100 140 100 140 630 250 250 240 6 6 6 120 46 7.2 7.2 2LC0131-7AA -0AA0 345 140 10 140 10 300 300 7.7 7.7 2LC0131-7AA -0AA0 370 10 220 10 220 355 355.4.4 2LC0131-7AA -0AA0 400 710 4000 1150 110 160 110 160 710 290 290 260 7 0 0 140 527 13 13 2LC0131-AA -0AA0 510 160 200 160 200 330 330 14 14 2LC0131-AA -0AA0 515 200 240 200 240 35 35 15 15 2LC0131-AA -0AA0 540 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 D2: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D2 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D2 Without order codes 3 1) Hub material EN-GJS 400 spheroidal graphite cast iron. /6 Siemens MD 10.1 2015

FLENDER Standard Couplings Type RWN - hub material grey cast iron Size Rated Speed Dimensions in mm Mass Article No. Weight Bore with keyway to moment of DIN 65 inertia 0 ShoreA T KN n Kmax D1 D2 DA ND1 ND2 NL1/ S U1 U2 P LG J 1 J 2 section 3 m min. max. min. max. NL2 Nm rpm kgm 2 kgm 2 kg 00 110000 1000 125 10 125 10 00 320 320 290 7 0 0 140 57 22 22 2LC0132-0AA -0AA0 670 10 220 10 220 360 360 23 23 2LC0132-0AA -0AA0 690 220 260 220 260 420 420 24.5 24.5 2LC0132-0AA -0AA0 730 900 150000 900 140 220 140 220 900 360 360 320 7.5 90 90 160 647.5 39 39 2LC0132-1AA -0AA0 940 220 260 220 260 425 425 41 41 2LC0132-1AA -0AA0 960 260 290 260 290 465 465 43 43 2LC0132-1AA -0AA0 1030 1000 195000 10 150 240 150 240 1000 395 395 350 7.5 90 90 160 707.5 60 60 2LC0132-2AA -0AA0 1200 240 20 240 20 460 460 63 63 2LC0132-2AA -0AA0 1250 20 320 20 320 515 515 6 6 2LC0132-2AA -0AA0 1310 1120 270000 700 160 200 160 200 1120 360 360 30.5 100 100 10 76.5 9 9 2LC0132-3AA -0AA0 1470 200 250 200 250 410 410 100 100 2LC0132-3AA -0AA0 1510 250 300 250 300 495 495 105 105 2LC0132-3AA -0AA0 1600 300 350 300 350 560 560 110 110 2LC0132-3AA -0AA0 1690 1250 345000 650 10 230 10 230 1250 410 410 420.5 100 100 10 4.5 150 150 2LC0132-4AA -0AA0 150 230 20 230 20 460 460 155 155 2LC0132-4AA -0AA0 1900 20 330 20 330 540 540 165 165 2LC0132-4AA -0AA0 2025 330 30 330 30 610 610 175 175 2LC0132-4AA -0AA0 2210 1400 530000 570 200 260 200 260 1400 465 465 40 9 120 120 210 969 290 290 2LC0132-5AA -0AA0 220 260 320 260 320 525 525 300 300 2LC0132-5AA -0AA0 2900 320 30 320 30 620 620 310 310 2LC0132-5AA -0AA0 310 30 440 30 440 700 700 330 330 2LC0132-5AA -0AA0 3260 1600 750000 500 260 320 260 320 1600 565 565 540 9 120 120 210 109 490 490 2LC0132-6AA -0AA0 370 320 30 320 30 625 625 500 500 2LC0132-6AA -0AA0 370 30 440 30 440 720 720 530 530 2LC0132-6AA -0AA0 4150 440 40 440 40 770 770 550 550 2LC0132-6AA -0AA0 4290 100 975000 450 320 30 320 30 100 660 660 600 12 140 140 240 1212 50 50 2LC0132-7AA -0AA0 5550 30 440 30 440 720 720 930 930 2LC0132-7AA -0AA0 5630 440 500 440 500 20 20 90 90 2LC0132-7AA -0AA0 6000 500 540 500 540 70 70 1050 1050 2LC0132-7AA -0AA0 6250 2000 1300000 400 30 440 30 440 2000 760 760 660 12 140 140 240 1332 1350 1350 2LC0132-AA -0AA0 600 440 500 440 500 20 20 1400 1400 2LC0132-AA -0AA0 7000 500 560 500 560 920 920 1500 1500 2LC0132-AA -0AA0 7350 560 600 560 600 960 960 1550 1550 2LC0132-AA -0AA0 7620 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 Without finished bore from size 1120 for 4th diameter range D1 Without order codes 4 D2: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D2 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D2 Without order codes 3 Without finished bore from size 1120 for 4th diameter range D2 Without order codes 4 From size 560 bores D1 and D2 are each provided with a recess of D = +1 mm halfway along the hub. 1/3 NL The hub diameter of the component part is assigned according to the diameter of the finished bore. Where bore diameters overlap, the component with the smaller hub diameter is always selected. Weight and mass moments of inertia apply to maximum bore diameters. Ordering example: RUPEX RWN coupling, size 710, Part 1: hub left with bore 10H7 mm, with keyway to DIN 65 and set screw, Part 2: hub right with bore 200H7 mm, with keyway to DIN 65 and set screw. Article No.: 2LC0131-AA99-0AA0 L2B+M2D The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. Siemens MD 10.1 2015 /7

FLENDER Standard Couplings Type RWS - hub material steel Selection and ordering data J1 J2 P U1 Part 1 U2 Part 2 ØND1 ØD1 ØD2 ØND2 NL1 LG S NL2 G_MD10_EN_00096 Size Rated Speed Dimensions in mm Mass Article No. Weight Bore with keyway to moment of DIN 65 inertia 0 ShoreA T KN n Kmax D1 D2 DA ND1 ND2 NL1/ S U1 U2 P LG J 1 J 2 section 3 m min. max. min. max. NL2 Nm rpm kgm 2 kgm 2 kg 105 200 10000 32 3 105 53 59 45 3 13 12 30 93 0.001 0.001 2LC0130-1AB -0AA0 1.9 125 350 9000 42 4 125 65 6 50 3 16 15 35 103 0.003 0.003 2LC0130-2AB -0AA0 3.2 144 500 700 50 60 144 76 4 55 3 16 15 35 113 0.004 0.006 2LC0130-3AB -0AA0 4.5 162 750 6900 55 65 162 5 92 60 3.5 20 1 40 123.5 0.007 0.013 2LC0130-4AB -0AA0 6.7 17 950 6300 70 75 17 102 10 70 3.5 20 1 40 143.5 0.014 0.022 2LC0130-5AB -0AA0 9.7 19 1300 5600 0 5 19 120 12 0 3.5 20 1 40 163.5 0.022 0.030 2LC0130-6AB -0AA0 12.9 22 2200 4900 5 95 22 129 140 90 3.5 26 24 50 13.5 0.03 0.071 2LC0130-7AB -0AA0 19 252 2750 4400 100 110 252 150 160 100 3.5 26 24 50 203.5 0.07 0.12 2LC0130-AB -0AA0 26.3 25 4300 3900 4 110 4 120 25 164 175 110 4.5 32 30 60 224.5 0.13 0.21 2LC0131-0AB -0AA0 39 320 5500 3500 55 125 55 130 320 10 192 125 4.5 32 30 60 254.5 0.23 0.32 2LC0131-1AB -0AA0 53 360 700 3100 65 135 65 140 360 200 210 140 4.5 42 42 75 24.5 0.41 0.69 2LC0131-2AB -0AA0 7 400 12500 200 75 150 75 150 400 230 230 160 4.5 42 42 75 324.5 0.92 0.92 2LC0131-3AB -0AA0 110 450 1500 2500 5 170 5 170 450 260 260 10 5.5 52 52 90 365.5 1.7 1.7 2LC0131-4AB -0AA0 163 500 25000 2200 95 190 95 190 500 290 290 200 5.5 52 52 90 405.5 2. 2. 2LC0131-5AB -0AA0 217 560 39000 2000 100 165 100 165 560 250 250 220 6 6 6 120 446 4. 4. 2LC0131-6AB -0AA0 274 165 200 165 200 300 300 5.2 5.2 2LC0131-6AB -0AA0 292 200 210 200 210 320 320 5.4 5.4 2LC0131-6AB -0AA0 305 630 52000 100 100 165 100 165 630 250 250 240 6 6 6 120 46 7.6 7.6 2LC0131-7AB -0AA0 352 165 200 165 200 300 300 7.9 7.9 2LC0131-7AB -0AA0 370 200 235 200 235 355 355.7.7 2LC0131-7AB -0AA0 400 710 4000 1600 110 190 110 190 710 290 290 260 7 0 0 140 527 14.4 14.4 2LC0131-AB -0AA0 507 190 220 190 220 330 330 14.6 14.6 2LC0131-AB -0AA0 530 220 250 220 250 35 35 15.9 15.9 2LC0131-AB -0AA0 560 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 D2: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D2 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D2 Without order codes 3 / Siemens MD 10.1 2015

FLENDER Standard Couplings Type RWS - hub material steel Size Rated Speed Dimensions in mm Mass Article No. Weight Bore with keyway to moment of DIN 65 inertia 0 ShoreA T KN n Kmax D1 D2 DA ND1 ND2 NL1 S U1 P LG J 1 J 2 section 3 m min. max. min. max. NL2 U2 Nm rpm kgm 2 kgm 2 kg 00 110000 1400 125 210 125 210 00 320 320 290 7 0 140 57 23.1 23.1 2LC0132-0AB -0AA0 63 210 240 210 240 360 360 23.3 23.3 2LC0132-0AB -0AA0 715 240 20 240 20 420 420 25.7 25.7 2LC0132-0AB -0AA0 762 900 150000 1250 140 210 140 210 900 320 320 320 7.5 90 160 647.5 40 40 2LC0132-1AB -0AA0 907 210 240 210 240 360 360 41 41 2LC0132-1AB -0AA0 933 240 20 240 20 425 425 44 44 2LC0132-1AB -0AA0 1000 20 310 20 310 465 465 45 45 2LC0132-1AB -0AA0 1025 1000 195000 1100 150 230 150 230 1000 355 355 350 7.5 90 160 707.5 63 63 2LC0132-2AB -0AA0 1170 230 260 230 260 395 395 64 64 2LC0132-2AB -0AA0 120 260 300 260 300 460 460 6 6 2LC0132-2AB -0AA0 1290 300 340 300 340 515 515 70 70 2LC0132-2AB -0AA0 1343 1120 270000 1000 160 240 160 240 1120 360 360 30.5 100 10 76.5 105 105 2LC0132-3AB -0AA0 1560 240 270 240 270 410 410 106 106 2LC0132-3AB -0AA0 1660 270 330 270 330 495 495 109 109 2LC0132-3AB -0AA0 1730 330 370 330 370 560 560 119 119 2LC0132-3AB -0AA0 170 1250 345000 900 10 270 10 270 1250 410 410 420.5 100 10 4.5 16 16 2LC0132-4AB -0AA0 2000 270 300 270 300 460 460 172 172 2LC0132-4AB -0AA0 2150 300 360 300 360 540 540 179 179 2LC0132-4AB -0AA0 2200 360 400 360 400 610 610 19 19 2LC0132-4AB -0AA0 2420 1400 530000 00 200 310 200 310 1400 465 465 40 9 120 210 969 316 316 2LC0132-5AB -0AA0 3020 310 350 310 350 525 525 322 322 2LC0132-5AB -0AA0 3120 350 410 350 410 620 620 337 337 2LC0132-5AB -0AA0 3350 410 460 410 460 700 700 357 357 2LC0132-5AB -0AA0 3570 1600 750000 700 260 370 260 370 1600 565 565 540 9 120 210 109 540 540 2LC0132-6AB -0AA0 390 370 410 370 410 625 625 554 554 2LC0132-6AB -0AA0 4270 410 40 410 40 720 720 57 57 2LC0132-6AB -0AA0 4300 40 510 40 510 770 770 611 611 2LC0132-6AB -0AA0 4630 100 975000 600 320 440 320 440 100 660 660 600 12 140 240 1212 1043 1043 2LC0132-7AB -0AA0 6230 440 40 440 40 720 720 1072 1072 2LC0132-7AB -0AA0 6460 40 540 40 540 20 20 1122 1122 2LC0132-7AB -0AA0 6770 540 50 540 50 70 70 1143 1143 2LC0132-7AB -0AA0 7030 2000 1300000 550 30 500 30 500 2000 760 760 660 12 140 240 1332 162 162 2LC0132-AB -0AA0 140 500 540 500 540 20 20 1664 1664 2LC0132-AB -0AA0 430 540 610 540 610 920 920 1735 1735 2LC0132-AB -0AA0 60 610 640 610 640 960 960 1793 1793 2LC0132-AB -0AA0 9050 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 Without finished bore from size 900 for 4th diameter range D1 Without order codes 4 D2: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D2 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D2 Without order codes 3 Without finished bore from size 900 for 4th diameter range D2 Without order codes 4 From size 560 bores D1 and D2 are each provided with a recess of D = +1 mm halfway along the hub. 1/3 NL The hub diameter of the component part is assigned according to the diameter of the finished bore. Where bore diameters overlap, the component with the smaller hub diameter is always selected. Weight and mass moments of inertia apply to maximum bore diameters. Ordering example: RUPEX RWS coupling, size 710, Part 1: Hub left with bore 10H7 mm, with keyway to DIN 65 and set screw, Part 2: Hub right with bore 200H7 mm, with keyway to DIN 65 and set screw. Coupling balanced G6.3 in accordance with the half parallel key standard. Article No.: 2LC0131-AB99-0AA0-Z L2B+M2D+W02 The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. Siemens MD 10.1 2015 /9

FLENDER Standard Couplings Type RFN with hub in grey cast iron Selection and ordering data Part 1 J1 J2 P U1 FB ZF x ØDFB ØND1 ØD1 ØDFN ØDFK ØDFA Part 20 G_MD10_EN_00097 S2 NL1 LG S L1 For dimensions U1, P and S2, see type RWN. Size Rated 0 ShoreA Speed Dimensions in mm Mass Bore with Flange connection keyway to DIN 65 From size 560 bore D1 is provided with a recess of D = +1 mm halfway along the hub. 1/3 NL moment of inertia Article No. section 3 T KN n Kmax D1 DA ND1 NL1 S LG DFA FB DFN L1 DFK ZF DFB J 1 J 2 m min. max. h H7 Nm rpm kgm 2 kgm 2 kg 105 200 7000 32 105 53 45 26 71 15 10 142 6 9 0.001 0.005 2LC0130-1AJ 1-0AA0 2.3 125 350 6000 42 125 65 50 31 1 10 13 160 6 11 0.003 0.012 2LC0130-2AJ 1-0AA0 4.2 144 500 5250 45 144 76 55 31 6 200 13 10 7 11 0.004 0.01 2LC0130-3AJ 1-0AA0 5.0 162 750 4650 50 162 5 60 37.5 97.5 220 13 200 11 0.007 0.032 2LC0130-4AJ 1-0AA0 7.3 17 950 4200 60 17 102 70 37.5 107.5 24 16 224 14 0.014 0.055 2LC0130-5AJ 1-0AA0 10 19 1300 3750 70 19 120 0 37.5 117.5 274 16 250 14 0.022 0.00 2LC0130-6AJ 1-0AA0 13 22 2200 3300 0 22 129 90 45.5 135.5 314 20 22 1 0.03 0.1 2LC0130-7AJ 1-0AA0 20 252 2750 3000 90 252 150 100 45.5 145.5 344 20 312 1 0.07 0.26 2LC0130-AJ 1-0AA0 25 25 4300 2650 4 100 25 164 110 55.5 165.5 30 22 34 9 1 0.13 0.46 2LC0131-0AJ 1-0AA0 3 320 5500 2350 55 110 320 10 125 55.5 175.5 430 25 390 9 22 0.23 0.76 2LC0131-1AJ 1-0AA0 50 360 700 2100 65 120 360 200 140 70.5 210.5 40 25 440 10 22 0.41 1.4 2LC0131-2AJ 1-0AA0 76 400 12500 2050 75 140 400 230 160 74.5 234.5 520 50 30 4 40 10 22 0.7 1. 2LC0131-3AJ 1-0AA0 125 450 1500 100 5 160 450 260 10 5.5 265.5 575 45 42 6 52 12 26 1.7 3.2 2LC0131-4AJ 1-0AA0 170 500 25000 1600 95 10 500 290 200 5.5 25.5 620 45 475 6 570 12 26 2. 4.3 2LC0131-5AJ 1-0AA0 205 560 39000 1450 100 140 560 250 220 106 326 700 65 532 650 16 26 4.6.2 2LC0131-6AJ 1-0AA0 330 140 10 300 5 2LC0131-6AJ 1-0AA0 330 10 200 320 5.1 2LC0131-6AJ 1-0AA0 340 630 52000 120 100 140 630 250 240 106 346 75 60 602 725 16 33 7.2 13. 2LC0131-7AJ 1-0AA0 390 140 10 300 7.7 2LC0131-7AJ 1-0AA0 400 10 220 355.4 2LC0131-7AJ 1-0AA0 420 710 4000 1150 110 160 710 290 260 127 37 75 0 675 10 15 1 33 13 26 2LC0131-AJ 1-0AA0 550 160 200 330 14 2LC0131-AJ 1-0AA0 550 200 240 35 15 2LC0131-AJ 1-0AA0 570 00 110000 1000 125 10 00 320 290 127 417 1000 70 765 10 930 16 39 22 45 2LC0131-9AJ 1-0AA0 60 10 220 360 23 2LC0131-9AJ 1-0AA0 690 220 260 420 24.5 2LC0131-9AJ 1-0AA0 710 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 Weight Weight and mass moments of inertia apply to maximum bore diameters. The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. /10 Siemens MD 10.1 2015

FLENDER Standard Couplings Type RFS in steel Selection and ordering data Part 1 J1 J2 P U1 FB ZF x ØDFB ØND1 ØD1 ØDFN ØDFK ØDFA Part 20 G_MD10_EN_00097 S2 NL1 LG S L1 For dimensions U1, P and S2, see type RWS. Size Rated 0 ShoreA Speed Dimensions in mm Mass Bore with Flange connection keyway to DIN 65 From size 560 bore D1 is provided with a recess of D = +1 mm halfway along the hub. 1/3 NL moment of inertia Article No. section 3 T KN n Kmax D1 DA ND1 NL1 S LG DFA FB DFN L1 DFK ZF DFB J 1 J 2 m min. max. h H7 Nm rpm kgm 2 kgm 2 kg 105 200 10000 32 105 53 45 26 71 15 10 142 6 9 0.001 0.005 2LC0130-1AK 1-0AA0 2.3 125 350 9000 42 125 65 50 31 1 10 13 160 6 11 0.003 0.012 2LC0130-2AK 1-0AA0 4.2 144 500 700 50 144 76 55 31 6 200 13 10 7 11 0.004 0.01 2LC0130-3AK 1-0AA0 5.0 162 750 6900 55 162 5 60 37.5 97.5 220 13 200 11 0.007 0.032 2LC0130-4AK 1-0AA0 7.3 17 950 6300 70 17 102 70 37.5 107.5 24 16 224 14 0.014 0.055 2LC0130-5AK 1-0AA0 10.0 19 1300 5600 0 19 120 0 37.5 117.5 274 16 250 14 0.022 0.00 2LC0130-6AK 1-0AA0 13 22 2200 4900 5 22 129 90 45.5 135.5 314 20 22 1 0.03 0.1 2LC0130-7AK 1-0AA0 20 252 2750 4400 100 252 150 100 45.5 145.5 344 20 312 1 0.07 0.26 2LC0130-AK 1-0AA0 25 25 4300 3900 4 110 25 164 110 55.5 165.5 30 22 34 9 1 0.13 0.46 2LC0131-0AK 1-0AA0 3 320 5500 3500 55 125 320 10 125 55.5 175.5 430 25 390 9 22 0.23 0.76 2LC0131-1AK 1-0AA0 50 360 700 3100 65 135 360 200 140 70.5 210.5 40 25 440 10 22 0.41 1.4 2LC0131-2AK 1-0AA0 76 400 12500 200 75 150 400 230 160 74.5 234.5 520 50 30 4 40 10 22 0.92 1. 2LC0131-3AK 1-0AA0 125 450 1500 2500 5 170 450 260 10 5.5 265.5 575 45 42 6 52 12 26 1.7 3.2 2LC0131-4AK 1-0AA0 175 500 25000 2200 95 190 500 290 200 5.5 25.5 620 45 475 6 570 12 26 2. 4.3 2LC0131-5AK 1-0AA0 210 560 39000 2000 100 165 560 250 220 106 326 700 65 532 650 16 26 4..2 2LC0131-6AK 1-0AA0 330 165 200 300 5.2 2LC0131-6AK 1-0AA0 340 200 210 320 5.4 2LC0131-6AK 1-0AA0 340 630 52000 100 100 165 630 250 240 106 346 75 60 602 725 16 33 7.6 13. 2LC0131-7AK 1-0AA0 390 165 200 300 7.9 2LC0131-7AK 1-0AA0 400 200 235 355.7 2LC0131-7AK 1-0AA0 420 710 4000 1600 110 190 710 290 260 127 37 75 0 675 10 15 1 33 14.4 26 2LC0131-AK 1-0AA0 550 190 220 330 14.6 2LC0131-AK 1-0AA0 560 220 250 35 15.9 2LC0131-AK 1-0AA0 50 00 110000 1400 125 210 00 320 290 127 417 1000 70 765 10 930 16 39 23.1 45 2LC0131-9AK 1-0AA0 690 210 240 360 23.3 2LC0131-9AK 1-0AA0 710 240 20 420 25.7 2LC0131-9AK 1-0AA0 730 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 Weight Weight and mass moments of inertia apply to maximum bore diameters. The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. Siemens MD 10.1 2015 /11

FLENDER Standard Couplings Type RWB with brake disk to DIN 15432 Selection and ordering data J1 L6 J2 BB Part 1 P U1 Part 3 ØND1 ØD1 S ØD2 ØND2 ØD6 ØDB NL1 LG NL2 G_MD10_EN_0009 Size Rated 0 ShoreA Dimensions in mm Bore with keyway to DIN 65 Brake disk T KN D1 D2 DA ND1 ND2 NL1 NL2 S U1 P LG DB DB D6 BB L6 min. max. min. max. max. max. max. min. min. Nm Article No. Plain text specification DB; BB; D6; NL2 required for order code section 3-0ZA0 144 500 45 45 144 76 4 55 219 3 16 35 277 500 315 175 30 34 2LC0130-3AE 162 750 50 50 162 5 92 60 219 3.5 20 40 22.5 560 315 175 30 34 2LC0130-4AE -0ZA0 17 950 60 60 17 102 10 70 219 3.5 20 40 292.5 560 355 200 30 34 2LC0130-5AE -0ZA0 19 1300 70 70 19 120 12 0 219 3.5 20 40 302.5 560 355 200 30 34 2LC0130-6AE -0ZA0 22 2200 0 0 22 129 140 90 219 3.5 26 50 312.5 00 450 250 30 34 2LC0130-7AE -0ZA0 252 2750 90 3 100 252 150 160 100 219 3.5 26 50 322.5 00 500 20 30 34 2LC0130-AE -0ZA0 25 4300 4 100 4 110 25 164 175 110 219 4.5 32 60 333.5 00 560 310 30 34 2LC0131-0AE -0ZA0 320 5500 55 110 55 120 320 10 192 125 219 4.5 32 60 34.5 1000 630 350 30 34 2LC0131-1AE -0ZA0 D1: Without finished bore Without order codes 1 D2: Without finished bore Without order codes 1 /12 Siemens MD 10.1 2015

FLENDER Standard Couplings Type RWB with brake disk to DIN 15432 Brake disk diameter DB in accordance with customer specification. Additional sizes are available on request. Further dimensions for part 3 on request. Maximum speed in rpm: n Kmax = 1146/DB DB in m Observe maximum speed of type RWN! Mass moments of inertia and weights can be sufficiently precisely determined as follows: Mass moments of inertia in kgm 2 : J 1 = J 1 from type RWN J 2 = J 2 from type RWN + 710 BB DB 4 BB and DB in m Weight in kg: m = m from type RWN + 5700 BB DB 2 BB and DB in m Ordering example: RUPEX RWB coupling, size 252, Part 1: Bore D1 = 4H7 mm, keyway to DIN 65-1 and set screw, Part 3: Brake disk DB = 630; BB = 30 mm; D6 = 350 mm, bore 42H7 mm, keyway to DIN 65-1 P9 and set screw. Hub reduced to NL2 = 200 mm Coupling micro-balanced G6.3 at 1500 rpm in accordance with the half parallel key standard. Mass moment of inertia: J 1 =0.07kgm 2 J 2 =0.12kgm 2 +3.3kgm 2 =3.42kgm 2 Weight: m = 26.3 kg + 6 kg = 94.3 kg Article No.: 2LC0130-AE99-0ZA0-Z L1B+M0X++W02 Plain text to : DB = 630 mm; BB = 30 mm; D6 = 350 mm; NL2 = 200 mm The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. Siemens MD 10.1 2015 /13

FLENDER Standard Couplings Type RBS with brake disk to DIN 15432 Sizes 144 to 360 Selection and ordering data J1 L6 J2 BB Part 1 P U1 Part 3 ØND1 ØD1 S ØD2 ØND2 ØD6 ØDB NL1 LG NL2 G_MD10_EN_0009 Size Rated 0 ShoreA Dimensions in mm Bore with keyway to DIN 65 Brake disk T KN D1 D2 DA ND1 ND2 NL1 NL2 S U1 P LG DB D6 BB L6 min. max. min. max. max. max. min. min. Nm Article No. Plain text specification DB; BB; D6; NL2 required for order code section 3-0ZA0 144 500 50 45 144 76 4 55 219 3 16 35 277 315 175 30 34 2LC0130-3AH 162 750 55 50 162 5 92 60 219 3.5 20 40 22.5 315 175 30 34 2LC0130-4AH -0ZA0 17 950 70 60 17 102 10 70 219 3.5 20 40 292.5 355 200 30 34 2LC0130-5AH -0ZA0 19 1300 0 70 19 120 12 0 219 3.5 20 40 302.5 355 200 30 34 2LC0130-6AH -0ZA0 22 2200 5 0 22 129 140 90 219 3.5 26 50 312.5 450 250 30 34 2LC0130-7AH -0ZA0 252 2750 100 3 100 252 150 160 100 219 3.5 26 50 322.5 500 20 30 34 2LC0130-AH -0ZA0 25 4300 4 110 4 120 25 164 175 110 219 4.5 32 60 333.5 560 310 30 34 2LC0131-0AH -0ZA0 320 5500 55 125 55 130 320 10 192 125 219 4.5 32 60 34.5 630 350 30 34 2LC0131-1AH -0ZA0 360 700 65 135 65 140 360 200 210 140 221 4.5 42 75 365.5 710 390 30 36 2LC0131-2AE -0ZA0 D1: Without finished bore Without order codes 1 D2: Without finished bore Without order codes 1 /14 Siemens MD 10.1 2015

Brake disk diameter DB in accordance with customer specification. Additional sizes are available on request. Further dimensions for part 3 on request. Maximum speed in rpm: n Kmax = 152/DB DB in m Observe maximum speed of type RWS! Mass moments of inertia and weights can be sufficiently precisely determined as follows: Mass moments of inertia in kgm 2 : J 1 = J 1 from type RWS J 2 = J 2 from type RWS + 770 BB DB 4 BB and DB in m Weight in kg: m = m from type RWS + 6160 BB DB 2 BB and DB in m Ordering example: RUPEX RBS coupling, size 252, Part 1: Bore D1 = 4H7 mm, keyway to DIN 65-1 and set screw, Part 3: Brake disk DB = 630 x BB = 30 mm, D6 = 350 mm, bore 42H7 mm, keyway to DIN 65-1 P9 and set screw. Hub reduced to NL2 = 200 mm Coupling micro-balanced G6.3 at 1500 rpm in accordance with the half parallel key standard. Mass moment of inertia: J 1 =0.07kgm 2 J 2 =0.12kgm 2 +3.6kgm 2 =3.72kgm 2 Weight: m = 25. kg + 73 kg = 9. kg Article No.: 2LC0130-AH99-0ZA0-Z L1B+M0X++W02 Plain text to : DB = 630 mm; BB = 30 mm; D6 = 350 mm; NL2 = 200 mm The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. FLENDER Standard Couplings Type RBS with brake disk to DIN 15432 Sizes 144 to 360 Siemens MD 10.1 2015 /15

FLENDER Standard Couplings Type RBS with brake disk to DIN 15432 Sizes 400 to 1000 Selection and ordering data J1 J2 L6 BB Part 1 P U1 Part 3 ØND1 ØD1 ØD2 ØND2 ØD6 ØDB NL1 LG S NL2 G_MD10_EN_00099 Size Rated 0 ShoreA Dimensions in mm Bore with keyway to DIN 65 Brake disk T KN D1 D2 DA ND1 ND2 NL1 NL2 S U1 P LG D6 BB L6 min. max. min. max. min. Nm Article No. Plain text specification DB; BB; D6; NL2 required for order code section 3-0ZA0 400 12500 75 150 75 150 400 230 230 160 225 4.5 42 75 39.5 440 30 40 2LC0131-3AH 450 1500 5 170 5 170 450 260 260 10 225 5.5 52 90 410.5 500 30 40 2LC0131-4AH -0ZA0 500 25000 95 190 95 190 500 290 290 200 225 5.5 52 90 430.5 500 30 40 2LC0131-5AH -0ZA0 560 39000 100 165 100 210 560 250 320 220 225 6 6 120 451 600 30 40 2LC0131-6AH -0ZA0 165 200 300 2LC0131-6AH -0ZA0 200 210 320 2LC0131-6AH -0ZA0 630 52000 100 165 100 235 630 250 355 240 240 6 6 120 46 670 30 55 2LC0131-7AH -0ZA0 165 200 300 2LC0131-7AH -0ZA0 200 235 355 2LC0131-7AH -0ZA0 710 4000 110 190 110 250 710 290 35 260 260 7 0 140 527 760 30 75 2LC0131-AH -0ZA0 190 220 330 2LC0131-AH -0ZA0 220 250 35 2LC0131-AH -0ZA0 00 110000 125 210 125 20 00 320 420 290 290 7 0 140 57 40 30 75 2LC0132-0AH -0ZA0 210 240 360 2LC0132-0AH -0ZA0 240 20 420 2LC0132-0AH -0ZA0 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 D2: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D2 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D2 Without order codes 3 /16 Siemens MD 10.1 2015

FLENDER Standard Couplings Type RBS with brake disk to DIN 15432 Sizes 400 to 1000 Size Rated 0 ShoreA Dimensions in mm Bore with keyway to DIN 65 From size 560 bore D1 is provided with a recess of D = +1 mm halfway along the hub. 1/3 NL Brake disk diameter DB in accordance with customer specification. Additional sizes are available on request. Further dimensions for part 3 on request. Maximum speed in rpm: n Kmax = 152/DB DB in m Observe maximum speed of type RWS! Mass moments of inertia and weights can be sufficiently precisely determined as follows: Mass moments of inertia in kgm 2 : J 1 = J 1 from type RWS J 2 = J 2 from type RWS + 770 BB DB 4 BB and DB in m Weight in kg: m = m from type RWS + 6160 BB DB 2 BB and DB in m Brake disk T KN D1 D2 DA ND1 ND2 NL1 NL2 S U1 P LG D6 BB L6 min. max. min. max. min. Nm Article No. Plain text specification DB; BB; D6; NL2 required for order code section 3-0ZA0 900 150000 140 210 140 310 900 320 465 320 7.5 90 160 647.5 950 30 75 2LC0132-1AH 210 240 360 2LC0132-1AH -0ZA0 240 20 425 2LC0132-1AH -0ZA0 20 310 465 2LC0132-1AH -0ZA0 1000 195000 150 230 150 340 1000 355 515 350 7.5 90 160 707.5 1050 30 75 2LC0132-2AH -0ZA0 230 260 395 2LC0132-2AH -0ZA0 260 300 460 2LC0132-2AH -0ZA0 300 340 515 2LC0132-2AH -0ZA0 D1: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D1 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D1 Without order codes 3 Without finished bore from size 900 for 4th diameter range D1 Without order codes 4 D2: Without finished bore up to size 500, from size 560 for 1st diameter range D1 Without order codes 1 Without finished bore from size 560 for 2nd diameter range D2 Without order codes 2 Without finished bore from size 560 for 3rd diameter range D2 Without order codes 3 Without finished bore from size 900 for 4th diameter range D2 Without order codes 4 Ordering example: RUPEX RBS coupling, size 450, Part 1: Bore D1 = 130H7 mm, keyway to DIN 65-1 and set screw, Part 3: Brake disk DB = 900; BB = 30 mm; D6 = 500 mm; bore 120H7 mm, keyway to DIN 65-1 P9 and set screw. Coupling micro-balanced G6.3 at 1500 rpm in accordance with the half parallel key standard. Mass moment of inertia: J 1 =1.74kgm 2 J 2 =1.74kgm 2 +15kgm 2 = 16.74 kgm 2 Weight: m = 25.kg + 149 kg = 174. kg Article No.: 2LC0131-4AH99-0ZA0-Z L1U+M1S++W02 Plain text to : DB = 900 mm; BB = 30 mm; D6 = 500 mm; NL2 = 322 mm The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. Siemens MD 10.1 2015 /17

FLENDER Standard Couplings Type RWB with brake drum to DIN 15431 Selection and ordering data J1 J2 Part 1 P U1 Part 32 ØND1 ØD1 ØD2 ØND2 ØDB BB G_MD10_EN_00100 NL1 S LG NL2 For dimensions U1 and P, see type RWN. Size Rated Speed Dimensions in mm Mass Article No. Weight Bore with keyway to moment of DIN 65 inertia 0 ShoreA T KN n Kmax D1 D2 DA ND1 ND2 NL1 NL2/ S DB LG J 1 J 2 section 3 m min. max. min. max. BB Nm rpm kgm 2 kgm 2 kg 144 500 3400 45 55 144 76 4 55 75 3 200 133 0.004 0.04 2LC0130-3AC -0BA0 9.5 162 750 2750 50 60 162 5 92 60 95 3.5 250 15.5 0.007 0.11 2LC0130-4AC -0CA0 17 17 950 2750 60 70 17 102 10 70 95 3.5 250 16.5 0.014 0.12 2LC0130-5AC -0CA0 20 2150 11 315 191.5 0.31 2LC0130-5AC -0DA0 2 19 1300 2750 70 0 19 120 12 0 95 3.5 250 17.5 0.022 0.13 2LC0130-6AC -0CA0 24 2150 11 315 201.5 0.32 2LC0130-6AC -0DA0 32 22 2200 1700 0 90 22 129 140 90 150 3.5 400 243.5 0.03 1.0 2LC0130-7AC -0EA0 54 252 2750 1700 90 3 100 252 150 160 100 150 3.5 400 253.5 0.07 1.0 2LC0130-AC -0EA0 63 1400 190 500 293.5 2. 2LC0130-AC -0FA0 93 25 4300 1400 4 100 4 110 25 164 175 110 190 4.5 500 304.5 0.13 2. 2LC0131-0AC -0FA0 104 1100 236 630 350.5 7. 2LC0131-0AC -0GA0 157 320 5500 1100 55 110 55 120 320 10 192 125 236 4.5 630 365.5 0.23 7.9 2LC0131-1AC -0GA0 172 950 265 710 394.5 13.9 2LC0131-1AC -0HA0 217 360 700 1100 65 120 65 130 360 200 210 140 236 4.5 630 30.5 0.41.1 2LC0131-2AC -0GA0 191 950 265 710 409.5 14.0 2LC0131-2AC -0HA0 236 D1: Without finished bore Without order codes 1 D2: Without finished bore Without order codes 1 Weight and mass moments of inertia apply to maximum bore diameters. Ordering example: RUPEX RWB coupling, size 252, Part 1: Bore 4H7 mm, keyway to DIN 65-1 and set screw, Part 3: 500 x 190, bore 42H7 mm, keyway to DIN 65-1 P9 and set screw. Coupling micro-balanced G6.3 at 1500 rpm in accordance with the half parallel key standard. Article No.: 2LC0130-AC99-0FA0-Z L1B+M0X+W02 The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. /1 Siemens MD 10.1 2015

FLENDER Standard Couplings Type RBS with brake drum to DIN 15431 Selection and ordering data J1 J2 Part 1 P U1 Part 32 ØND1 ØD1 ØD2 ØND2 ØDB BB G_MD10_EN_00100 NL1 S LG NL2 For dimensions U1 and P, see type RWS Size Rated Speed Dimensions in mm Mass Article No. Weight Bore with keyway to moment of DIN 65 inertia 0 ShoreA T KN n Kmax D1 D2 DA ND1 ND2 NL1 NL2 S DB LG J 1 J 2 section 3 m min. max. min. max. BB Nm rpm kgm 2 kgm 2 kg 144 500 5000 50 60 144 76 4 55 75 3 200 133 0.004 0.04 2LC0130-3AD -0BA0 10 162 750 5000 55 65 162 5 92 60 95 3.5 250 15.5 0.007 0.13 2LC0130-4AD -0CA0 1 17 950 4900 70 75 17 102 10 70 95 3.5 250 16.5 0.014 0.13 2LC0130-5AD -0CA0 22 4350 11 315 191.5 0.34 2LC0130-5AD -0DA0 30 19 1300 4600 0 5 19 120 12 0 95 3.5 250 17.5 0.022 0.14 2LC0130-6AD -0CA0 26 4350 11 315 201.5 0.35 2LC0130-6AD -0DA0 35 22 2200 3400 5 95 22 129 140 90 150 3.5 400 243.5 0.03 1.1 2LC0130-7AD -0EA0 60 252 2750 3400 100 3 110 252 150 160 100 150 3.5 400 253.5 0.067 1.1 2LC0130-AD -0EA0 6 2750 100 190 500 293.5 3.1 2LC0130-AD -0FA0 103 25 4300 2750 4 110 4 110 25 164 175 110 190 4.5 500 304.5 0.13 3.1 2LC0131-0AD -0FA0 115 2150 236 630 350.5.5 2LC0131-0AD -0GA0 171 320 5500 2150 55 125 55 125 320 10 192 125 236 4.5 630 365.5 0.23.6 2LC0131-1AD -0GA0 15 1900 265 710 394.5 14. 2LC0131-1AD -0HA0 230 360 700 2150 65 135 65 135 360 200 210 140 236 4.5 630 30.5 0.41.9 2LC0131-2AD -0GA0 210 1900 265 710 409.5 15.1 2LC0131-2AD -0HA0 255 D1: Without finished bore Without order codes 1 D2: Without finished bore Without order codes 1 Weight and mass moments of inertia apply to maximum bore diameters. Ordering example: RUPEX RBS coupling, size 252, Part 1: Bore 4H7 mm, keyway to DIN 65-1 and set screw, Part 3: 500 x 190, bore 42H7 mm, keyway to DIN 65-1 P9 and set screw. Coupling micro-balanced. Article No.: 2LC0130-AD99-0FA0-Z L1B+M0X+W02 The article number applies to standard s of 0 ShoreA; the article number for alternative types is available on request. Siemens MD 10.1 2015 /19

FLENDER Standard Couplings Spare and wear parts Selection and ordering data ØDB L M G_MD10_XX_00101 ØDB L M G_MD10_XX_00103 Sizes 105... 400 Sizes 710... 2000 ØDB L M G_MD10_XX_00102 Sizes 450... 630 Buffers and pins The s of RUPEX couplings are wear parts. The service life depends on the operating conditions. Size Identification Number per set Article No. for a set of s DA DB L M Buffer Perbunan 0 Weight m Article No. for a set of pins Pin complete, ShoreA incl. fasteners mm mm mm kg kg 105 105 20 45 M6 2LC0130-1WA00-0AA0 0.043 2LC0130-1WB00-0AA0 0.14 125 125 24 10 53.5 M 2LC0130-2WA00-0AA0 0.09 2LC0130-2WB00-0AA0 0.2 144 125 10 24 10 53.5 M 2LC0130-3WA00-0AA0 0.12 2LC0130-3WB00-0AA0 0.35 * ) 125 59.5 2LC0130-3WB00-0AA0-Z Y99 0.4 162 162 9 30 12 64.5 M10 2LC0130-4WA00-0AA0 0.17 2LC0130-4WB00-0AA0 0.57 * ) 162 67.5 2LC0130-4WB00-0AA0-Z Y99 0.60 17 162 10 30 12 64.5 M10 2LC0130-5WA00-0AA0 0.19 2LC0130-5WB00-0AA0 0.65 * ) 162 67.5 2LC0130-5WB00-0AA0-Z Y99 0.67 19 162 12 30 12 64.5 M10 2LC0130-6WA00-0AA0 0.23 2LC0130-6WB00-0AA0 0.76 * ) 162 67.5 2LC0130-6WB00-0AA0-Z Y99 0.0 22 22 11 40 16 79 M12 2LC0130-7WA00-0AA0 0.42 2LC0130-7WB00-0AA0 1.40 252 22 12 40 16 79 M12 2LC0130-WA00-0AA0 0.45 2LC0130-WB00-0AA0 1.50 25 25 11 4 20 9 M16 2LC0131-0WA00-0AA0 0.1 2LC0131-0WB00-0AA0 2.50 320 25 12 4 20 9 M16 2LC0131-1WA00-0AA0 0. 2LC0131-1WB00-0AA0 2.0 360 360 10 64 25 123 M1 2LC0131-2WA00-0AA0 1.6 2LC0131-2WB00-0AA0 4.4 400 360 14 64 25 123 M1 2LC0131-3WA00-0AA0 2.2 2LC0131-3WB00-0AA0 6.1 450 450 12 7 32 123 M16 2LC0131-4WA00-0AA0 3.5 2LC0131-4WB00-0AA0 11 500 450 14 7 32 123 M16 2LC0131-5WA00-0AA0 4.0 2LC0131-5WB00-0AA0 13 560 560 12 101 42 15 M20 2LC0131-6WA00-0AA0 7.1 2LC0131-6WB00-0AA0 25 630 560 14 101 42 15 M20 2LC0131-7WA00-0AA0.3 2LC0131-7WB00-0AA0 29 710 710 14 120 50 15.5 M24 2LC0131-WA00-0AA0 14 2LC0131-WB00-0AA0 49 00 710 16 120 50 15.5 M24 2LC0132-0WA00-0AA0 16 2LC0132-0WB00-0AA0 56 900 900 16 136 55 207.5 M24 2LC0132-1WA00-0AA0 24 2LC0132-1WB00-0AA0 71 1000 900 1 136 55 207.5 M24 2LC0132-2WA00-0AA0 27 2LC0132-2WB00-0AA0 0 1120 1120 1 155 60 232.5 M30 2LC0132-3WA00-0AA0 41 2LC0132-3WB00-0AA0 110 1250 1120 20 155 60 232.5 M30 2LC0132-4WA00-0AA0 45 2LC0132-4WB00-0AA0 125 1400 1400 20 175 70 274 M30 2LC0132-5WA00-0AA0 65 2LC0132-5WB00-0AA0 15 1600 1400 24 175 70 274 M30 2LC0132-6WA00-0AA0 7 2LC0132-6WB00-0AA0 225 100 100 22 200 0 327 M36 2LC0132-7WA00-0AA0 115 2LC0132-7WB00-0AA0 320 2000 100 26 200 0 327 M36 2LC0132-WA00-0AA0 135 2LC0132-WB00-0AA0 30 Weight m *) Only for type RWB with brake disk and type RBS with brake disk. Plain text to Y99: "Types RWB/RBS with brake disk" /20 Siemens MD 10.1 2015