Compact Guide Cylinder ø2,,, ø2,,, ø0, ø63,, ø0 With air cushion Water resistant cylinder are now available. New Up to 7% Weight reduced! New Weight reduced by up to 7% with a shorter guide rod and thinner plate With air cushion Water resistant cylinder Max. Guide rod shortened for M40-2 stroke 22mm Space required between the bottom of the cylinder body and your equipment is reduced. Space saving Round type and magnetic field resistant auto switches are mountable directly without spacer. 3 types of bearing can be selected. Slide bearing Series M Ball bushing Series L High precision ball bushing Series Series Change of guide rod end shape (-X ), intermediate stroke (-XB), low speed cylinder (-XB3), side porting type (-X867), made of stainless steel (-XC6), adjustable stroke cylinder/adjustable extension type (-XC8), and with coil scraper (-XC3) etc. are now available. CT.S20-29C
Compact Guide Cylinder 3 types of bearing can be selected. Slide bearing Series M Suitable for lateral load applications such as a stopper where shock is applied Ball bushing Series L Smooth operation suitable for pusher and lifter High precision ball bushing Series Suitable for minimizing plate displacement Slide bearing Ball bushing High precision ball bushing Load from lateral direction Displacement 'Weight reduced Reduction rate (%) Weight (kg) ø2 ø2 ø0 ø63 ø0 3 2 2 7 6 7 7 7 3 0.2 0.37 0.9 0.84.4.64 2.79 3.48.4 9.2 Compared with the slide bearing type, ø2 to ø2-20 stroke Compared with the slide bearing type, to ø0-2 stroke Basic Type 'Guide rod shortened Projection Shortened Guide rod Guide rod Shortened by New dimension ø0 ø63 ø0 22 22 8 8... 9 6.. 8. Compared with the slide bearing type, 2 stroke ( to ø0) (No projection for ø2 to ø2-2 stroke) 'Performance and strength (rigidity) are equivalent to the conventional series. 'Mounting dimensions are equivalent to the conventional series. Series (Basic Type), Stroke Variations Bearing type M Slide bearing L Ball bushing High precision ball bushing Features 2 6 20 2 32 40 0 63 80 0 Stroke 20 2 30 40 0 7 0 2 7 200 20 300 30 400 -X : Change of guide rod end shape -XB6: Heat resistant cylinder ( to C) -XB: Intermediate stroke (Using exclusive body) -XB3: Low speed cylinder ( to 0 mm/s) -XC6: Made of stainless steel -XC8: djustable stroke cylinder/djustable extension type -XC22: Fluororubber seal -XC3: With coil scraper -XC79: Machining tapped hole, drilled hole and pin hole additionally -XC82: Bottom mounting type -X44: Symmetrical port position -X867: Side porting type (Plug location changed) Refer to front matter for details.
Series Small auto switches or magnetic field resistant auto switches can be mounted on 2 surfaces. D-M9 D-9 D-P3DW The D-Y7 and D-Z7 auto switches are not mountable. 4 types of mounting are possible.. Top mounting asy positioning Knock pin holes provided on each mounting surface 2. Side mounting 4. Bottom mounting 3. T-slot side mounting asy adjustment of workpiece and cylinder mounting D-P3DW Piping is possible from 2 directions.. Top ported 2. Side ported D-M9 'Weight reduced by up to 24% Reduction rate (%) Weight (kg) ø2 ø0 ø63 ø0 2 8 22 24 23 23 22 2 9.28.9 2.2 3.7 4.3 6.6 8.04.3 7.72 Compared with the conventional M with air cushion, 200 stroke With ir Cushion 'Guide rod shortened by up to 3. mm (M0-0) Projection Shortened Guide rod Guide rod Shortened by New dimension ø0 ø63 ø0 33. 33. 22 22 3. 3. 9 2. 2. 7.. Compared with the conventional M with air cushion, 0 stroke 'Performance and strength are equivalent to the conventional series with air cushion. 'Mounting dimensions are equivalent to the conventional series with air cushion. Series (With ir Cushion), Stroke Variations Bearing type M- Slide bearing L- Ball bushing - High precision ball bushing 6 20 2 32 40 0 63 80 0 Stroke 2 0 7 0 2 7 200 20 300 30 400 -XC9: Intermediate stroke (Spacer type) -XC79: Tapped hole, drilled hole, pinned hole machined additionally -X867: Side porting type (Plug location changed) Refer to front matter for details. Features 2
Compact Guide Cylinders, Series Variations Series -Z Series Bearing type 6 2 6 20 2 32 40 0 63 80 0 Basic type/ Page New Slide bearing Page 3 Ball bushing With air cushion/- High precision ball bushing Page 23 Water resistant cylinder/ R/V Slide bearing Page Series With end lock/-h/r Slide bearing For details, refer to the WB catalog or the following page. LOCK Ball bushing High precision ball bushing Best Pneumatics Page 380 Clean series/2/3- Ball bushing Best Pneumatics Page 37 Heavy duty guide rod/s Best Pneumatics Page 390 Miniature Guide Rod Cylinder/MGJ Slide bearing Best Pneumatics Page 30 Compact Guide Cylinder with Lock /MLGP LOCK Slide bearing Ball bushing Best Pneumatics Page 99 Hygienic Design Cylinder/HYG Slide bearing Best Pneumatics Page 9 Features 3
Combination of Standard Products and Specifications Series V : Standard : v : Special product (Please contact SMC for details.) : Not available Type Bearing type Model Slide bearing Basic type Ball bushing High precision ball bushing Slide bearing With air cushion Ball bushing High precision ball bushing M L M L Symbol Specifications pplicable bore size ø2 to ø0 to ø0 Basic type V V V With air cushion V V V 2- Copper (Cu) and Zinc (Zn)-free Note ) ø2 to ø0 V V With ir Cushion Basic Type 20- Copper and Fluorine-free Note ) ø2 to ø0 V V Note 3) V Note 3) V V Note 3) Note 3) V R/V Water resistant to ø0 V -X Change of guide rod end shape -XB6 Heat resistant cylinder ( to C) Note 2) ø2 to ø0 -XB Intermediate stroke (Using exclusive body) uto Switch -XB3 Low speed cylinder ( to 0 mm/s) -XC4 With heavy duty scraper to ø0 -XC6 Made of stainless steel -XC8 djustable stroke cylinder/djustable extension type ø2 to ø0 -XC9 djustable stroke cylinder/djustable retraction type Note 2) -XC9 Intermediate stroke (Spacer type) to ø0 -XC22 Fluororubber seal Note 2) ø2 to ø0 -XC3 With coil scraper to ø0 -XC79 Tapped hole, drilled hole, pinned hole machined additionally -XC82 Bottom mounting type -XC8 Grease for food processing equipment ø2 to ø0 -X44 Symmetrical port position -X867 Side porting type (Plug location changed) Note ) Refer to the WB catalog for details. Note 2) Without cushion Note 3) Copper and fluorine-free are available as standard products. Front matter
Series Specific Product Precautions Be sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to Handling Precautions for SMC Products and the Operation Manual on SMC website, http://www.smcworld.com Warning Mounting. Never place your hands or fingers between the plate and the body. Be very careful to prevent your hands or fingers from getting caught in the gap between the cylinder body and the plate when air is applied. Caution Mounting 6. Bottom of cylinder The guide rods protrude from the bottom of the cylinder at the end of the retracting stroke, and therefore, in cases where the cylinder is to be bottom mounted, it is necessary to provide bypass ports in the mounting surface for the guide rods, as well as holes for the hexagon socket head cap screws which are used for mounting. Moreover, in applications where impact occurs from a stopper etc., the mounting screws should be inserted to a depth of 2d or more. Caution. Use cylinders within the piston speed range. n orifice is set for this cylinder, but the piston speed may exceed the operating range if the speed controller is not used. If the cylinder is used outside the operating speed range, it may cause damage to the cylinder and shorten the service life. djust the speed by installing the speed controller and use the cylinder within the limited range. 2. Pay attention to the operating speed when the product is mounted vertically. When using the product in the vertical direction, if the load factor is large, the operating speed can be faster than the control speed of the speed controller (i.e. quick extension). In such cases, it is recommended to use a dual speed controller. 3. Do not scratch or gouge the sliding portion of the piston rod and the guide rod. Damaged seals etc. will result in leakage or malfunction. 4. Do not dent or scratch the mounting surface of the body and the plate. The flatness of the mounting surface may not be maintained, which would cause an increase in sliding resistance.. Make sure that the cylinder mounting surface has a flatness of 0.0 mm or less. If the flatness of the workpieces and brackets mounted on the plate is not appropriate, sliding resistance may increase. If it is difficult to maintain a flatness of 0.0 or less, put a thin shim ring (prepared by user) between the plate and workpiece mounting surface to prevent the sliding resistance from increasing. Shim ring (prepared by user) Workpiece Plate B C±0.2 ±0.2 C ød 2d or more (d = Screw O.D.) Bypass port dia. * ir cushions are not available for bore size 2. B±0.2 D M L/ Hexagon socket head cap screw 2 * 0 8 4 8 M4 x 0.7 6 6 22 46 2 M x 0.8 20 72 24 4 4 2 M x 0.8 2 82 30 64 8 M6 x.0 32 98 34 78 22 8 M8 x.2 40 6 40 86 22 8 M8 x.2 0 30 46 27 22 M x. 63 42 8 24 27 22 M x. 80 80 4 6 33 28 M2 x.7 0 2 62 88 39 33 M4 x 2.0
Series Specific Product Precautions 2 Be sure to read before handling. Refer to back cover for Safety Instructions. For ctuator and uto Switch Precautions, refer to Handling Precautions for SMC Products and the Operation Manual on SMC website, http://www.smcworld.com Caution Plug Piping Depending on the operating conditions, piping port positions can be changed by using a plug.. M fter tightening by hand, tighten additional /6 to /4 rotation with a tightening tool. 2. Tapered thread for Rc port () and NPT port ( TN) Use the correct tightening torques listed below. Before tightening the plug, wrap pipe tape around it. lso, with regard to the sunk dimension of a plug (dimension a in the drawing), use the stipulated figures as a guide and confirm the air leakage before operation. * If tightening plugs on the top mounting port with more than the proper tightening torque, plugs will be screwed much deeply and air passage will be squeezed. Consequently, the cylinder speed will be restricted. Connection thread (plug) size Proper tightening torque (N m) a a dimension /8 7 to 9 0. mm or less /4 2 to 4 mm or less 3/8 22 to 24 mm or less Load mass (kg) Caution 00 0 ø0 ø63 ø0 ø2 ø2 llowable Kinetic nergy Load mass and a maximum speed must be within the ranges shown in the graph below. with Rubber Bumper With ir Cushion Basic Type uto Switch 3. Parallel pipe thread for G port ( TF) Screw in the plug to the surface of the body (dimension a in the drawing) by checking visually instead of using the tightening torque shown in the table. With air cushion Warning. Do not open the cushion valve excessively. ir leakage will occur if operated after opening by 4 rotations or more. Furthermore, a stopper mechanism is provided for the cushion valve, and it should not be forced open beyond that position. Be aware that the cushion valve may jump up from the cover when the air is supplied. Caution Cushion. Be sure to use the cylinder after the air cushion has been adjusted appropriately. First, fully close the cushion valve. Start the operation at the cylinder speed to be used with the load applied, and then open the cushion valve gradually to make the adjustment. The optimal adjustment is that the piston reaches its stroke end and the collision sound is minimized. If the cushion valve is used without adjusting the air cushion appropriately, this may cause damage to the retaining ring or piston. pplicable tool 6, 20, 2, 32, 40 JIS B4648 hexagon wrench key. 0, 63, 80, 0 JIS B4648 hexagon wrench key 3 2. Be sure to operate a cylinder equipped with air cushion to the end of the stroke. If it is not operated to the end of the stroke, the effect of the air cushion will not be fully exhibited. Consequently, in cases where the stroke is regulated by an external stopper etc., caution must be exercised, as the air cushion may become completely ineffective. Load mass (kg) 0. 0.0 0 00 00 with ir Cushion 00 0 ø0 ø63 ø0 ø2 Maximum speed (mm/s) 0 00 00 Maximum speed (mm/s) 2
Compact Guide Cylinder Series ø2,,, ø2,,, ø0, ø63,, ø0 How to Order M 2 30 Z M9BW Compact Guide Cylinder For details, refer to page 4. M L Bearing type Slide bearing Ball bushing High precision ball bushing 2 2 mm 40 40 mm 6 6 mm 0 0 mm 20 20 mm 63 63 mm 2 2 mm 80 80 mm 32 32 mm 0 0 mm Port thread type Nil M x 0.8 Rc TN NPT TF G * For bore sizes ø2 and, only M x 0.8 is available. uto switch Without auto switch Nil (Built-in magnet) * For applicable auto switches, refer to the table below. Cylinder stroke Refer to Standard Strokes on page 4. Number of auto switches Nil 2 pcs. S pc. n n pcs. pplicable uto Switches/Refer to the WB catalog or the Best Pneumatics No. 3 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color display) Water resistant (2-color display) Magnetic field resistant (2-color display) lectrical entry Grommet Indicator light Yes Wiring (Output) Load voltage uto switch model Lead wire length (m) DC C Perpendicular In-line 0. (Nil) (M) 3 (L) (Z) Pre-wired connector pplicable load 3-wire (NPN) M9NV M9N IC V, 2 V 3-wire (PNP) M9PV M9P circuit 2-wire 2 V M9BV M9B 3-wire (NPN) M9NWV M9NW IC V, 2 V 3-wire (PNP) M9PWV M9PW circuit 2-wire 24 V 2 V M9BWV M9BW 3-wire (NPN) M9NV *** M9N *** IC V, 2 V 3-wire (PNP) M9PV *** M9P *** circuit 2-wire 2 V M9BV *** M9B *** 2-wire (Non-polar) P3DW ** 3-wire IC V Yes (NPN equivalent) 96V 96 circuit Grommet 0 V 93V 93 Relay, 2-wire 24 V 2 V No 0 V or less 90V 90 IC circuit PLC *** Water resistant type auto switches are mountable on the above models, but in such case SMC cannot guarantee water resistance. water resistant type cylinder is recommended for use in an environment which requires water resistance. However, please contact SMC for water resistant products of ø2 and. * Lead wire length symbols: 0. m Nil (xample) M9NW m M (xample) M9NWM 3 m L (xample) M9NWL * Solid state auto switches marked with v are produced upon receipt of order. ** The D-P3DW is mountable on bore size ø2 to ø0. m Z (xample) M9NWZ * Since there are other applicable auto switches than listed above, refer to the WB catalog or the Best Pneumatics No. 3 for details. * For details about auto switches with pre-wired connector, refer to the WB catalog or the Best Pneumatics No. 3. For the D-P3DW, refer to the WB catalog. * uto switches are shipped together, (but not assembled). Relay, PLC 3
Compact Guide Cylinder Series Specifications Symbol Rubber bumper 2 6 20 2 32 40 0 63 80 0 ction Double acting Fluid ir Proof pressure. MPa Maximum operating pressure.0 MPa Minimum operating pressure 0.2 MPa 0. MPa mbient and fluid temperature to 60 C (No freezing) Piston speed Note) 0 to 00 mm/s 0 to 400 mm/s Cushion Rubber bumper on both ends Lubrication Not required (Non-lube) Stroke length tolerance Standard Strokes +. 0 mm Note) Maximum speed with no load. Make a model selection, considering a load according to the graph on pages 9 to. With ir Cushion Basic Type Symbol (For details, refer to pages 44 to.) Specifications -Xm Change of guide rod end shape -XB6 Heat resistant cylinder ( to C) -XB Intermediate stroke (Using exclusive body) -XB3 Low speed cylinder ( to 0 mm/s) -XC4 With heavy duty scraper -XC6 Made of stainless steel -XC8 djustable stroke cylinder/djustable extension type -XC9 djustable stroke cylinder/djustable retraction type -XC22 Fluororubber seal -XC3 With coil scraper -XC79 Tapped hole, drilled hole, pinned hole machined additionally -XC82 Bottom mounting type -XC8 Grease for food processing equipment -X44 Symmetrical port position -X867 Side porting type (Plug location changed) Refer to pages 40 to 42 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Standard stroke 2, 6, 20, 30, 40, 0, 7, 0, 2,, 7, 200, 20 20, 2 20, 30, 40, 0, 7, 0, 2,, 7, 200, 20, 300, 30, 400 32 to 0 2, 0, 7, 0, 2,, 7, 200, 20, 300, 30, 400 Manufacture of Intermediate Strokes Spacer installation type xclusive body (-XB) Description Spacers are installed in the standard stroke cylinder. Dealing with the stroke by making an exclusive body. ø2 to : vailable by the mm stroke interval. ll bore sizes are available by the mm interval. to ø0: vailable by the mm stroke interval. Model no. Refer to How to Order for the standard model numbers. dd -XB to the end of standard model number. For details, refer to. pplicable stroke xample Theoretical Output Rod size 2 6 6 8 20 2 32 4 40 4 0 8 63 8 80 22 0 26 ø2, to 249 ø2, to 249, ø2, to 399, ø2 2 to 399 to ø0 to 39 to ø0 26 to 399 Part no.: M20-39Z spacer mm in width is installed in the M20-40. C dimension is 77 mm. Operating direction Piston area (mm 2 ) OUT Operating pressure (MPa) 0.2 0.3 0.4 0. 0.6 0.7 0.8 0.9.0 OUT 3 23 34 4 7 68 79 90 2 3 IN 8 7 2 34 42 9 68 76 8 OUT 20 40 60 80 2 4 6 8 20 IN 30 4 60 7 90 6 2 36 OUT 34 63 94 26 7 88 220 2 283 34 IN 236 47 7 94 8 4 6 88 22 236 OUT 49 98 47 96 24 29 344 393 442 49 IN 42 82 24 6 206 247 289 330 37 42 OUT 804 6 24 322 402 483 63 643 724 804 IN 60 30 9 260 32 390 4 20 8 60 OUT 27 2 377 03 628 74 880 0 3 27 IN 3 22 33 44 662 772 882 992 3 OUT 963 393 89 78 982 78 374 7 767 963 IN 709 342 3 684 8 2 96 367 38 709 OUT 37 623 93 247 9 870 282 2494 2806 37 IN 2863 73 89 4 43 78 2004 2290 276 2863 OUT 027 0 8 20 23 306 39 402 424 027 IN 4646 929 394 89 2323 2788 322 377 482 4646 OUT 784 7 236 342 3927 472 498 6283 7069 784 IN 7323 46 297 2929 3662 4394 26 88 69 7323 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) Part no.: M20-39Z-XB Special body manufactured for 39 stroke. C dimension is 76 mm. IN (N) 4 uto Switch
Series Weights Slide Bearing: M2 to 0 Standard stroke 20 2 30 40 0 7 0 2 7 200 20 300 30 400 2 0.22 0.2 0.29 0.33 0.36 0.46 0. 0.66 0.7 0.84 0.93. 6 0.32 0.37 0.42 0.46 0. 0.66 0.78 0.94.06.8.3. 20 0.9 0.67 0.74 0.82.06.24.43.6.80.99 2.42 2.79 3.6 3.3 2 0.84 0.94.04.4.0.7 2.00 2.2 2.0 2.7 3.3 3.8 4.34 4.84 32.4.77 2.22 2.7 2.93 3.29 3.6 4.00 4.90.6 6.33 7.04 40.64 2.04 2.2 2.92 3.32 3.7 4. 4.0.47 6.26 7.06 7.8 0 2.79 3.38 4.3 4.7.30.89 6.47 7.06 8. 9.73.9 2. 63 3.48 4. 4.99.67 6.34 7.02 7.69 8.37.0.4 2.7 4. 80.4 6.26 7.4 8.26 9. 9.9.8.6 3.9.6 7.3 9.0 0 9.2.3 2.0 3.2 4.4.6 6.9 8. 2.2 23.6 26. 28. (kg) Ball Bushing: L2 to 0, High Precision Ball Bushing: 2 to 0 Standard stroke 20 2 30 40 0 7 0 2 7 200 20 300 30 400 2 0.2 0.24 0.27 0.32 0.3 0.43 0.0 0.9 0.67 0.7 0.83 0.99 6 0.3 0.3 0.40 0.47 0. 0.62 0.72 0.8 0.96.06.7.38 20 0.60 0.66 0.79 0.8.0.7.36.2.68.84 2.7 2.49 2.8 3.3 2 0.87 0.96.2.20.4.62.86 2.06 2.27 2.48 2.92 3.33 3.7 4.6 32.37.66 2.08 2.37 2.74 3.03 3.3 3.60 4.2 4.82.39.97 40.9.92 2.38 2.70 3. 3.44 3.77 4.09 4.8.46 6. 6.76 0 2.6 3.4 3.8 4.34 4.97.47.96 6.4 7.7 8.6 9.4. 63 3.33 3.9 4.7.29 6.0 6.9 7.7 7.7 9.0.2.4 2. 80.27 6.29 7.49 8.2 8.92 9.64.4. 2.9 4.3.7 7.2 0 8.62..8 2.9 3.9.0 6.0 7. 9.6 2.7 23.8 2.9 (kg) Water Resistant Cylinder Ideal for use in a machine tool environment exposed to coolants. pplicable for use in an environment with water splashing such as food processing and car wash equipment, etc. How to Order M R Stroke Thread type Water resistant 2-color indication solid state switch Nil Rc Water resistant cylinder N NPT R NBR seals (Nitrile rubber) TF G V FKM seals (Fluororubber) Stainless steel plate is available as special products. Piston rod and guide rod are made of stainless steel. Z M9l(V)L Specifications pplicable series M Bearing type Slide bearing 20, 2, 32, 40, 0, 63, 80, 0 Cushion MllR Rubber bumper MllV Without cushion Specifications other than above are the same as standard, basic type. Note) Refer to the WB catalog for details. Dimensions ød (Piston rod O.D.) FB B + Stroke + Stroke 0 st Over 0 st Over B D 0 st Over 0 st Over or less 200 st or less 200 st or less 200 st or less 200 st FB 20 66 90. 23 66 () (0) (24.) (7) 2 2 67. 9. 23. 67. () (0) (24) (6) 2 32 87. 4. 7. (4) (.) (34) (70) 24 40 87. 4. 78 (4) (9) (27.) (63.) 24 0 99. 20. 6. 83 20 (6.) (37.) (78.) 27 63 99. 20. 6. 88 20 (.) (32.) (73.) 27 80. 37. 86. 2. 2 (8) (3) (84) 30 0 30.. 94. 20 30 (.) (3.) (74.) 3 * The dimensions in ( ) are the same as standard type.
Compact Guide Cylinder Series llowable Rotational Torque of Plate Torque: T (N m) 2 6 20 2 32 40 0 63 80 0 T (N m) Bearing type Stroke 20 2 30 40 0 7 0 2 7 200 20 300 30 400 M 0.39 0.32 0.27 0.24 0.2 0.43 0.36 0.3 0.27 0.24 0.22 0.9 L/ 0.6 0.4 0.3 0.8 0.0 0.37 0.29 0.24 0.20 0.8 0.6 0.2 M 0.69 0.8 0.49 0.43 0.38 0.69 0.8 0.0 0.44 0.40 0.36 0.30 L/ 0.99 0.74 0.9 0.99 0.86 0.6 0.2 0.43 0.37 0.32 0.28 0.23 M.0 0.93 0.83 0.7.88.63.44.28.6.06 0.90 0.78 0.69 0.62 L/.26.03 2.7.94.2.2.34.7.03 0.93 0.76 0.6 0.6 0.49 M.76..38.2 2.96 2.7 2.26 2.02.83.67.42.24.09 0.98 L/ 2..7 3.37 3.02 2.38.97 2.0.78.8.4.6 0.98 0.8 0.74 M 6.3.3.69 4.97 4.42 3.98 3.6 3.3 2.84 2.48 2.20.98 L/.9 4.89. 4. 6.34.79.33 4.93 4.29 3.78 3.38 3.04 M 7.00.66 6.27.48 4.87 4.38 3.98 3.6 3.3 2.74 2.43 2.9 L/ 6..39.62 4.96 6.98 6.38.87.43 4.72 4.6 3.7 3.3 M 3.0.8 2.0.6 9.0 8.60 7.86 7.24 6.24.49 4.90 4.43 L/ 9.7 7.62 9.83 8.74.6.7 9.83 9.2 7.9 7.02 6.26.63 M 4.7 2. 3..9.7 9.69 8.86 8.6 7.04 6.9.2 4.99 L/.2 8.48.0 9.74 3.0.9.0.2 8.84 7.80 6.94 6.24 M 2.9 8.6 22.9 20. 8.6 7.0.6 4. 2.6.2.0 9. L/. 23.3 22.7 20.6 8.9 7.3 6.0 4.8 2.9.3.0 8.94 M 38.8 33. 37. 33.8 30.9 28.4 26.2 24.4 2.4 9. 7.2.7 L/ 27. 30.6 37.9 34.6 3.8 29.3 27.2 2.3 22. 9. 7.3. With ir Cushion Basic Type uto Switch Non-rotating ccuracy of Plate Non-rotating accuracy q when retracted and when no load is applied should be not more than the values shown in the table. 2 6 20 2 32 40 0 63 80 0 +θ θ Non-rotating accuracy q M L ±0.07 ±0.0 ±0.06 ±0.04 ±0.0 ±0.03 ±0.04 ±0.03 ±0.03 ±0.03 ±0.0 High Precision Ball Bushing/ Caution Positioning accuracy for pin hole on the plate Dispersion of dimensions when machining each component will be accumulated in the plate pin hole positioning accuracy when mounting this cylinder. Values below are referred as a guide. [Side mounting] Pin hole [Bottom mounting] Pin hole L * = Catalog dimension ± (0. + L x 0.0008) [mm] * : To be 0. for, ø0 Note) Displacement by load and self-weight deflection by plate and guide rod are not included. B L2 Pin hole B = ± (0.04 + L2 x 0.006) [mm] 6
Series High Precision Ball Bushing/ Plate Displacement mount (Reference Values) Load from lateral direction Displacement 2 Plate displacement amount Plate displacement amount Plate displacement amount Plate displacement amount 0.4 0.3 0.3 0.2 0.2 0. 0. 2-20 2-2-0 2-7 2-0 0.0 2-0 0 20 2 Load from lateral direction (N) 6 0.4 0.3 0.3 0.2 0.2 0. 0. 6-20 6-6-0 6-7 6-0 0.0 6-0 0 20 30 Load from lateral direction (N) 20 0.7 0.6 0. 0.4 0.3 0.2 0. 2 20-400 20-300 20-200 20-20-0 20-0 0 0 20 40 60 Load from lateral direction (N) 0.7 0.6 0. 0.4 0.3 2-400 2-300 2-200 0.2 2-2-0 0. 2-0 0 0 20 40 60 80 Load from lateral direction (N) 32, 40 Plate displacement amount Plate displacement amount Plate displacement amount 0.8 0.7 0.6 0. 32 40-400 32 40-300 0.4 32 40-200 0.3 32 40-32 0.2 40-0 0. 32 40-0 0 0 20 40 60 80 0 Load from lateral direction (N) 0, 63 0.7 0.6 0. 0.4 0.3 0.2 0. 80 Plate displacement amount 0 63-400 0 63-300 0 63-200 0 63-0 63-0 0 63-0 0 0 20 40 60 80 0 Load from lateral direction (N) 0.4 0.4 0.3 0.3 0.2 0.2 0. 0. 0.0 0 80-400 80-300 80-20 80-200 80-80-0 80-0 0 0 0 0 200 Load from lateral direction (N) 0.6 0. 0.4 0.3 0.2 0. 0-400 0-300 0-20 0-200 0-0-0 0-0 0 0 0 200 300 Load from lateral direction (N) Note ) The guide rod and self-weight for the plate are not included in the above displacement values. Note 2) llowable rotating torque, and operating range when used as a lifter, are the same as those of the L series. 7
Basic Type Series Model Selection Selection Conditions Vertical Horizontal L L L L m m Mounting orientation m m Maximum speed (mm/s) 200 or less 400 200 or less 400 Graph (Slide bearing) (), (2) (3), (4) (3), (4) (), (6) Graph (Ball bushing) () to (8) (9) to (2) (7), (8) (9), (20) Selection xample (Vertical Mounting) Selection conditions Mounting: Vertical Bearing type: Ball bushing Stroke: 30 stroke Maximum speed: 200 mm/s Load mass: 3 kg ccentric distance: 90 mm Find the point of intersection for the load mass of 3 kg and the eccentric distance of 90 mm on graph (), based on vertical mounting, ball bushing, 30 stroke, and the speed of 200 mm/s. L2-30Z is selected. () 30 stroke or less, V = 200 mm/s or less 20 ø2 ø2 Selection xample 2 (Horizontal Mounting) Selection conditions Mounting: Horizontal Bearing type: Slide bearing Distance between plate and load center of gravity: 0 mm Maximum speed: 200 mm/s Load mass: 2 kg Stroke: 30 stroke Find the point of intersection for the load mass of 2 kg and 30 stroke on graph (3), based on horizontal mounting, slide bearing, the distance of 0 mm between the plate and load center of gravity, and the speed of 200 mm/s. M20-30Z is selected. (3) L = 0 mm, V = 200 mm/s or less 0 ø0 ø0, 63, 40 ø2 ø2 ø0, 63, 40 ø0 ø2 ø2 0. 0 0 200 ccentric distance L 0. 30 0 0 200 300 Stroke When the maximum speed exceeds 200 mm/s, the allowable load mass is determined by multiplying the value shown in the graph at 400 mm/s by the coefficient listed in the table below. Max. speed Up to 300 mm/s Up to 400 mm/s Up to 00 mm/s Coefficient.7 0.6 Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more. 9
L m L m Model Selection Series Vertical Mounting M2 to 0 300 200 0 ø0 ø63 ø0 ø2 Slide Bearing 300 200 0 ø0 ø63 ø0 ø2 Operating pressure 0.4 MPa Operating pressure 0. MPa or more () 0 stroke or less, V = 200 mm/s or less (2) Over 0 stroke, V = 200 mm/s or less With ir Cushion Basic Type ø2 ø2 uto Switch 0. 0. 0 0 200 0 0 200 ccentric distance L ccentric distance L (3) 0 stroke or less, V = 400 mm/s (4) Over 0 stroke, V = 400 mm/s 0 0 ø0 0 0 ø0 ø63 ø63 ø0 ø2 ø0 ø2 ø2 ø2 0. 0. 0 0 200 0 0 200 ccentric distance L ccentric distance L Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more.
Series L m L m Vertical Mounting Ball Bushing Operating pressure 0.4 MPa Operating pressure 0. MPa or more L2 to 2, 2 to 2 () 30 stroke or less, V = 200 mm/s or less (6) Over 30 stroke, V = 200 mm/s or less 20 20 ø2 ø2 ø2 ø2 0. 0. 0 0 200 0 0 200 ccentric distance L ccentric distance L L32 to 0, 32 to 0 (7) 0 stroke or less, V = 200 mm/s or less (8) Over 0 stroke, V = 200 mm/s or less 300 300 0 ø0 ø63 0 ø0 0 ø0 0 ø63 ø0 0 200 ccentric distance L 0 0 200 ccentric distance L Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more.
L m L m Model Selection Series Vertical Mounting ø2 Ball Bushing Operating pressure 0.4 MPa L2 to 2, 2 to 2 (9) 30 stroke or less, V = 400 mm/s () Over 30 stroke, V = 400 mm/s 0. 0. ø2 With ir Cushion Basic Type ø2 ø2 uto Switch 0. 0.0 0 0 200 0 0 200 ccentric distance L ccentric distance L L32 to 0, 32 to 0 () 0 stroke or less, V = 400 mm/s (2) Over 0 stroke, V = 400 mm/s 0 0 ø0 0 0 ø0 ø63 ø0 ø63 ø0 0 0 200 ccentric distance L 0.2 0 0 200 ccentric distance L Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more. 2
Series L L Horizontal Mounting Slide Bearing m m M2 to 0 (3) L = 0 mm, V = 200 mm/s or less (4) L = 0 mm, V = 200 mm/s or less 0 ø0 ø0, 63, 40 ø0, 63, 40 ø0 ø2 0 ø0 ø0 ø0, 63 ø0, 63, 40, 40 ø2 ø2 ø2 ø2 ø2 ø2 ø2 0. 30 0 0 200 300 Stroke 0. 30 0 0 200 300 Stroke () L = 0 mm, V = 400 mm/s (6) L = 0 mm, V = 400 mm/s 0 ø0 ø0 ø63 ø63 ø0 ø0 ø2 ø2 0 ø0 ø0, 63 ø2 ø0 ø0, 63 ø2 ø2 ø2 ø2 ø2 3 0. 30 0 0 200 300 Stroke 0. 30 0 0 200 300 Stroke
L L Model Selection Series Horizontal Mounting Ball Bushing m m (7) L = 0 mm, V = 200 mm/s or less (8) L =0 mm, V = 200 mm/s or less L2 to 2, 2 to 2 L2 to 2, 2 to 2 ø2 ø2 ø2 ø2 ø2 ø2 ø2 ø2 ø2 With ir Cushion Basic Type ø2 ø2 ø2 0. 30 3 0 0 200 300 Stroke L32 to 63, 32 to 63 0 0. 30 3 0 0 200 300 Stroke L32 to 63, 32 to 63 0 uto Switch ø0, 63, 40 ø0, 63, 40 ø0, 63, 40 ø0, 63, 40 ø0, 63, 40 ø0, 63, 40 30 0 0 200 300 Stroke L80/0, 80/0 0 L80/0, 80/0 0 30 0 0 200 300 Stroke ø0 ø0 ø0 ø0 ø0 ø0 29 30 0 0 200 300 Stroke 29 30 0 0 200 300 Stroke 4
Series L L Horizontal Mounting Ball Bushing m m (9) L = 0 mm, V = 400 mm/s (20) L =0 mm, V = 400 mm/s L2 to 2, 2 to 2 L2 to 2, 2 to 2 ø2 ø2 ø2 ø2 ø2 ø2 0. 0 ø2 ø2 30 3 0 0 200 300 Stroke L32 to 63, 32 to 63 ø2 0. 30 3 0 0 200 300 Stroke L32 to 63, 32 to 63 0 ø2 ø2 ø2 ø0, 63 ø0, 63 ø63 ø0 30 0 0 200 300 ø0, 63 ø0, 63 ø63 ø0 30 0 0 200 300 Stroke Stroke L80/0, 80/0 0 L80/0, 80/0 0 ø0 ø0 ø0 ø0 ø0 ø0 29 30 0 0 200 300 Stroke 29 30 0 0 200 300 Stroke
Model Selection Series Operating Range when Used as Stopper Bore Size: ø2 to ø2/m2 to 2 (Slide Bearing) L 0 mm υ m L 0 mm * When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling υ m Note ) When using as a stopper, select a model with 30 stroke or less. Note 2) The L (Ball bushing) and the (High precision ball bushing) cannot be used as a stopper. M2 to 2 (Slide Bearing) Mass of transferred object: m (kg) 0 0 40 30 20 4 3 2 ø2 ø2 Transfer speed: υ (m/min) 20 30 40 0 With ir Cushion Basic Type uto Switch Bore Size: to ø0/m32 to 0 (Slide Bearing) L 0 mm m υ L 0 mm * When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with 0 stroke or less. Note 2) The L (Ball bushing) and the (High precision ball bushing) cannot be used as a stopper. m υ M32 to 0 (Slide Bearing) Mass of transferred object: m (kg) 2000 00 00 400 300 200 0 0 40 30 ø0 ø63 ø0 20 30 40 0 Transfer speed: υ (m/min) * Refer to graphs (3) and () if line pressure is applied by a roller conveyor after the workpiece is stopped. 6
Series Construction/Series M M2 to 2 M32 to 0 u!0 o @2 e i r @3 y!6 q!2 w!4 @ @4!0 t!3!! o @2 e i u!0 r!6 @3 y q!6!2 w!4 @ @4!0 t!3!9! @0 ø63 or more ø2 to ø2 0 stroke or less ø2 to ø2 Over 0 stroke ø0 or more Component Parts No. Description Material Note Body luminum alloy Hard anodized 2 Piston luminum alloy Chromated 3 Piston rod Stainless steel ø2 to ø2 Carbon steel to ø0 Hard chrome plating 4 Collar luminum alloy Chromated Head cover luminum alloy ø2 to ø63 Chromated, ø0 Painted 6 Guide rod Carbon steel Hard chrome plating 7 Plate Carbon steel Nickel plating 8 Plate mounting bolt Carbon steel Nickel plating 9 Guide bolt Carbon steel Nickel plating Retaining ring Carbon tool steel Phosphate coated Retaining ring Carbon tool steel Phosphate coated 2 Bumper Urethane 3 Bumper B Urethane 4 Magnet Plug ø2, Carbon steel Hexagon socket head plug to ø0 Nickel plating 6 Slide bearing Bearing alloy Component Parts No. Description Material Note 7 Ball bushing 8 Spacer luminum alloy 9 Steel ball Carbon steel ø2 to ø0 20 Plug Carbon steel ø63 to ø0 Nickel plating 2 * Piston seal NBR 22 * Rod seal NBR 23 * Gasket NBR 24 * Gasket B NBR Replacement Parts/Seal Kit Kit no. Contents 2 2-Z-PS Set of 6 6-Z-PS nos. 20 20-Z-PS above 2 2-Z-PS @, @2, 32 32-Z-PS @3, @4 Kit no. Contents 40 40-Z-PS Set of 0 0-Z-PS nos. 63 63-Z-PS above 80 80-Z-PS @, @2, 0 0-Z-PS @3, @4 * Seal kit includes @ to @4. Order the seal kit, based on each bore size. * Since the seal kit does not include a grease pack, order it separately. Grease pack part number: GR-S-0 ( g) 7
Compact Guide Cylinder Series Construction/Series L, Series L2 to 2 2 to 2!!7 L32 to 0 32 to 0!!7 With ir Cushion Basic Type!8 uto Switch ø2 to ø2 Over 0 stroke ø0 or more!8 to ø63 Over 0 stroke, ø0 Over 200 stroke 8
a T R øxh7 b Z WB W XB X 3 6 c d e ød Z W ødb PW U X H V VB Series ø2 to ø2/m, L, øx H7 depth 6 Section XX details T-slot dimensions X (Mounting hole position) Section XX 4 x YY depth YL X±0.02 (Pin hole position) a b c d e 2 4.4 7.4 3.7 2 6.2 6 4.4 7.4 3.7 2. 6.7 20.4 8.4 4. 2.8 7.8 2.4 8.4 4. 3 8.2 Bottom view 4 x NN through Section XX X±0.02 4 x øo through 4 x øob counterbore depth OL (OL) X±0.02 L 4 x MM depth ML Section XX H: T-slot for hexagon bolt øx H7 depth 6 Q S P + Stroke F G GB FB C + Stroke B + Stroke + Stroke 2 x P 2 x P (Plug) 3 PB J K G ø2, T-slot øx H7 depth 6 * The use of a slot (width X, length XB, depth 3) allows for a relaxed pin pitch tolerance, with the pin hole (øxh7, depth 6) as the reference, without affecting mounting accuracy. * For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Strokes on page 4. * For bore size ø2 and, only M x 0.8 port is available. * For bore size or more, choice of Rc, NPT, G port is available. (Refer to page 3.) M, L, Common Dimensions P Standard stroke B C D F FB G G GB H H J K L MM ML NN O OB OL Nil TN TF 2, 20, 30, 40, 0, 7, 0 42 29 6 7 6 26 7 8 M4 3 3 8 M4 x 0.7 M4 x 0.7 4.3 8 4. M x 0.8 6 2,, 7, 200, 20 46 33 8 7 6 30. 7. 64 M4 22 M x 0.8 2 M x 0.8 4.3 8 4. M x 0.8 20 20, 30, 40, 0, 7, 0, 2, 3 37 8 8 36. 9 83 M 8 8 24 M x 0.8 3 M x 0.8.4 9.. Rc/8 NPT/8 G/8 2 7, 200, 20, 300, 30, 400 3. 37. 9 7 42. 93 M 2 2 30 M6 x.0 M6 x.0.4 9.. Rc/8 NPT/8 G/8 W WB P PB PW Q R S T U V VB 30 st Over 30 st Over 0 st Over 200 st Over 30 st Over 30 st Over 0 st Over 200 st Over or less 0 st or less 200 st or less 300 st or less 300 st or less 0 st or less 200 st or less 300 st or less 300 st X X XB YY YL Z 2 3 8 8 4 48 22 6 4 0 37 20 40 200 2 60 23 3 3. M x 0.8 6 4. 9 6 4 2 62 46 6 38 24 44 200 7 27 60 24 3 3. M x 0.8 20 3.. 2 8 70 30 8 4 72 44 24 44 20 200 300 29 39 77 7 67 28 3 3. M6 x.0 2 7 2 2. 3. 30 26 78 38 9 64 82 0 24 44 20 200 300 29 39 77 7 67 34 4 4. M6 x.0 2 7 M (Slide bearing), DB, Dimensions DB 9 0 st Over 0 st Over 0 st Over 0 st Over 0 st Over 0 st Over or less 0 st or less 200 st or less 200 st or less 0 st or less 200 st or less 200 st 2 42 60. 82. 82. 8 0 8. 40. 40. 6 46 64. 92. 92. 0 8. 46. 46. 20 3 77. 77. 2 0 24. 24. 7 2 3. 77. 77. 9. 6 0 24 24 6 L (Ball bushing) (High precision ball bushing), DB, Dimensions DB 30 st or less Over 30 st Over 0 st 0 st or less 200 st or less Over 200 st 30 st or less Over 30 st Over 0 st 0 st or less 200 st or less Over 200 st 2 43 84. 84. 6 3 42. 42. 6 49 6 94. 94. 8 3 9 48. 48. 20 9 76 0 7. 6 23 47 64. 2 6. 8. 0. 7. 3 2 28 47 64
ødb PW T R X U H V VB b Compact Guide Cylinder Series to ø63/m, L, 4 x NN through Section XX X (Mounting hole position) Section XX øx H7 depth XL Z W WB 4 x YY depth YL Bottom view Z W X±0.02 (Pin hole position) Section XX details X XB øxh7 XC 4 x øo through 4 x øob counterbore depth OL XL L T-slot dimensions c e d a 4 x MM depth ML Section XX a b c d e 32 6... 3. 9. 40 6... 4 0 8. 3. 7. 4. 3. 63 7.8 7 8. With ir Cushion Basic Type X±0.02 ød (OL) X±0.02 H: T-slot for hexagon bolt uto Switch Q S øx H7 depth XL F G GB FB C + Stroke B + Stroke + Stroke 2 x P P + Stroke 2 x P (Plug) PB J G K T-slot øx H7 depth XL * The use of a slot (width X, length XB, depth XC) allows for a relaxed pin pitch tolerance, with the pin hole (øxh7, depth XL) as the reference, without affecting mounting accuracy. * For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Strokes on page 4. * Choice of Rc, NPT, G port is available. (Refer to page 3.) M, L, Common Dimensions Standard P stroke B C D F FB G G GB H H J K L MM ML NN O OB OL Nil TN TF 32 2, 0, 7 9. 37. 4 2 48 2 9 2 M6 24 24 34 M8 x.2 20 M8 x.2 6.7 7. Rc/8 NPT/8 G/8 40 0, 2, 66 44 4 2 4 2 20 M6 27 27 40 M8 x.2 20 M8 x.2 6.7 7. Rc/8 NPT/8 G/8 0 7, 200, 20 72 44 8 2 6 64 2 48 M8 32 32 46 M x. 22 M x. 8.6 4 9 Rc/4 NPT/4 G/4 63 300, 30, 400 77 49 8 2 6 78. 3. 62 M 39 39 8 M x. 22 M x. 8.6 9 Rc/4 NPT/4 G/4 W WB P PB PW Q R S T U V VB X X XB XC XL YY YL Z 2 st Over 2 st Over 0 st Over 200 st Over 2 st Over 2 st Over 0 st Over 200 st Over or less 0 st or less 200 st or less 300 st or less 300 st or less 0 st or less 200 st or less 300 st or less 300 st 32 6. 6 3. 30 96 44 78 98 63 24 48 24 200 300 33 4 83 2 7 42 4 4. 3 6 M8 x.2 6 2 40 3 8 39. 30 4 44 8 86 6 72 24 48 24 200 300 34 46 84 22 72 0 4 4. 3 6 M8 x.2 6 22 0 9 2. 47 40 30 60 46 30 92 24 48 24 200 300 36 48 86 24 74 66 6 4 8 M x. 20 24 63 3 28 8 0 30 70 8 24 42 28 2 28 200 300 38 0 88 24 74 80 6 4 8 M x. 20 24 M (Slide bearing), DB, Dimensions DB 0 st or less Over 0 st 200 st or less Over 200 st 0 st or less Over 0 st 200 st or less Over 200 st 32 7 93. 29. 20. 34 70 40 7 93. 29. 20 9 27. 63. 0 88. 9.. 2 6. 37. 78. 63 88. 9.. 2. 32. 73. L (Ball bushing) (High precision ball bushing), DB, Dimensions DB 0 st or less Over 0 st Over 0 st 0 st or less 200 st or less Over 200 st 0 st or less Over 0 st Over 0 st 0 st or less 200 st or less Over 200 st 32 79. 96. 6. 38. 6 20 37 7 79 40 79. 96. 6. 38. 6 3. 30. 0. 72. 0 9. 2. 32. 9. 20 9. 40. 60. 87. 63 9. 2. 32. 9. 20 4. 3.. 82. 20
a ødb PW R T ød U X VB V H b Series, ø0/m, L, ø6 H7 depth Z W WB Section XX details T-slot dimensions X (Mounting hole position) X±0.02 (Pin hole position) 6 7 ø6h7 c e d a b c d e 80 3.3 20.3 2 8 22. 0.3 23.3 3. 30 Section XX 4 x YY depth YL Bottom view 4 x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth OL L 4 x MM depth ML Section XX (OL) X±0.02 X±0.02 H: T-slot for hexagon bolt ø6 H7 depth Q S F GC G GB FB C + Stroke B + Stroke + Stroke 2 x P P + Stroke 2 x P (Plug) JB PB JC J J G K T-slot ø6 H7 depth * The use of a slot (width X6, length 7, depth ) allows for a relaxed pin pitch tolerance, with the pin hole (ø6h7, depth ) as the reference, without affecting mounting accuracy. * For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Strokes on page 4. * Choice of Rc, NPT, G port is available. (Refer to page 3.) M, L, Common Dimensions Standard P stroke B C D F FB G G GB GC H H J J JB JC K L MM ML NN O OB OL Nil TN TF 80 2, 0, 7, 0 96. 6. 22 6 24 9. 9 6. 4. 202 M2 4. 38 7. 46 4 M2 x.7 2 M2 x.7.6 7. 3 Rc3/8 NPT3/8 G3/8 2,, 7, 200 0 20, 300, 30, 400 6 66 26 9 3. 22. 20. 8 240 M4. 4. 6 62 M4 x 2.0 3 M4 x 2.0 2. 20 8 Rc3/8 NPT3/8 G3/8 M (Slide bearing), DB, Dimensions L (Ball bushing) (High precision ball bushing), DB, Dimensions DB DB 2 P PB PW Q R S T U V VB 0 st or less Over 0 st 200 st or less Over 200 st 0 st or less 2 st or less Over 2 st 0 st or less Over 0 st 200 st or less Over 200 st 80 4. 3. 80. 30 8 3 84 0 26.. 90. 36. 3. 74. W Over 0 st Over 200 st 200 st or less 300 st or less Over 300 st 2 st or less Over 2 st 0 st or less WB Over 0 st Over 200 st 200 st or less 300 st or less Over 300 st X YY YL Z 80 4. 2. 74 2 74 7 98 6 80 40 28 2 28 200 300 42 4 92 28 78 0 M2 x.7 24 28 0 7. 32. 89 64 2 90 236 88 2 66 48 72 48 220 320 3 47 8 2 7 24 M4 x 2.0 28 2 st Over 2 st Over 0 st Over 2 st Over 2 st Over 0 st Over or less 0 st or less 200 st or less 200 st or less 0 st or less 200 st or less 200 st 80 4. 28. 8. 9. 2 8 32 62 9 0 9. 4. 78. 20. 30 3. 29. 62. 8.
Compact Guide Cylinder With ir Cushion Series,, ø2,,, ø0, ø63,, ø0 How to Order M 32 0 Z M9BW Compact Guide Cylinder For details, refer to page 24. M L Bearing type Slide bearing Ball bushing High precision ball bushing 6 6 mm 0 0 mm 20 20 mm 63 63 mm 2 2 mm 80 80 mm 32 32 mm 0 0 mm 40 40 mm Port thread type Nil TN TF M x 0.8 Rc NPT G * For bore size 6, only M x 0.8 is available. With air cushion Cylinder stroke Refer to Standard Strokes on page 24. uto switch Without auto switch Nil (Built-in magnet) * For applicable auto switches, refer to the table below. Number of auto switches Nil S n 2 pcs. pc. n pcs. pplicable uto Switches/Refer to the WB catalog or the Best Pneumatics No. 3 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (2-color display) Water resistant (2-color display) Magnetic field resistant (2-color display) lectrical entry Grommet Grommet *** Water resistant type auto switches are mountable on the above models, but in such case SMC cannot guarantee water resistance. water resistant type cylinder is recommended for use in an environment which requires water resistance. However, please contact SMC for water resistant products of ø2 and. * Lead wire length symbols: 0. m Nil (xample) M9NW m M (xample) M9NWM 3 m L (xample) M9NWL m Z (xample) M9NWZ Indicator light Wiring (Output) Load voltage uto switch model Lead wire length (m) DC C Perpendicular In-line * Solid state auto switches marked with v are produced upon receipt of order. ** The D-P3DW is mountable on bore size ø2 to ø0. * Since there are other applicable auto switches than listed above, refer to the WB catalog or the Best Pneumatics No. 3 for details. * For details about auto switches with pre-wired connector, refer to the WB catalog or the Best Pneumatics No. 3. For the D-P3DW, refer to the WB catalog. * uto switches are shipped together, (but not assembled). 0. (Nil) (M) 3 (L) (Z) Pre-wired connector pplicable load 3-wire (NPN) M9NV M9N IC V,2 V 3-wire (PNP) M9PV M9P circuit 2-wire 2 V M9BV M9B 3-wire (NPN) M9NWV M9NW IC V,2 V 3-wire (PNP) M9PWV M9PW circuit Yes 2-wire 24 V 2 V M9BWV M9BW 3-wire (NPN) M9NV *** M9N *** IC V,2 V 3-wire (PNP) M9PV *** M9P *** circuit 2-wire 2 V M9BV *** M9B *** v 2-wire (Non-polar) 3-wire (NPN equivalent) P3DW ** V IC circuit Relay, PLC V 96V 96 Yes 0 V 93V 93 Relay, 2-wire 24 V 2 V No 0 V or less 90V 90 IC circuit PLC 23
Compact Guide Cylinder With ir Cushion Series Specifications Symbol ir cushion ction Fluid 6 20 2 32 40 0 63 80 0 Proof pressure Maximum operating pressure Double acting Standard stroke 6 2, 0, 7, 0, 2,, 7, 200, 20 20 to 63 2, 0, 7, 0, 2,, 7, 200, 20, 300, 30, 400 80, 0 0, 7, 0, 2,, 7, 200, 20, 300, 30, 400 ir. MPa.0 MPa Minimum operating pressure 0. MPa 0.2 MPa mbient and fluid temperature to 60 C (No freezing) Piston speed 0 to 00 mm/s 0 to 400 mm/s Cushion Lubrication Stroke length tolerance Standard Strokes ir cushion on both ends (Without bumper) Not required (Non-lube) +. 0 mm With ir Cushion Basic Type Symbol (For details, refer to pages 44 to.) Specifications -XC9 Intermediate stroke (Spacer type) -XC79 Tapped hole, drilled hole, pinned hole machined additionally -XC8 Grease for food processing equipment -X867 Side porting type (Plug location changed) Refer to pages 40 to 42 for cylinders with auto switches. uto switch proper mounting position (detection at stroke end) and its mounting height Minimum stroke for auto switch mounting Operating range uto switch mounting brackets/part no. Manufacture of Intermediate Strokes Description Model no. pplicable stroke xample Intermediate strokes by the mm interval are available by replacing collars of a standard stroke cylinder. Minimum manufacturable stroke Note) Intermediate stroke (by the mm interval) based on an exclusive body will be available upon request for special. Theoretical Output to ø63: mm, ø0: 20 mm Select a rubber bumper type, because the cushion effect is not obtainable for less than this stroke. dd -XC9 to the end of standard part number. to 249 to ø63 to 399, ø0 20 to 399 Part no.: M20-3Z-XC9 collar mm in width is installed in the M20-0Z. C dimension is 2 mm. OUT IN uto Switch Rod size 6 8 20 2 32 4 40 4 0 20 63 20 80 2 0 30 Operating direction Piston area (mm 2 ) Operating pressure (MPa) 0.2 0.3 0.4 0. 0.6 0.7 0.8 0.9.0 OUT 20 40 60 80 2 4 6 8 20 IN 30 4 60 7 90 6 2 36 OUT 34 63 94 26 7 88 220 2 283 34 IN 236 47 7 94 8 4 6 88 22 236 OUT 49 98 47 96 24 29 344 393 442 49 IN 42 82 24 6 206 247 289 330 37 42 OUT 804 6 24 322 402 483 63 643 724 804 IN 60 30 9 260 32 390 4 20 8 60 OUT 27 2 377 03 628 74 880 0 3 27 IN 3 22 33 44 662 772 882 992 3 OUT 963 393 89 78 982 78 374 7 767 963 IN 649 330 49 660 82 990 4 39 484 649 OUT 37 623 93 247 9 870 282 2494 2806 37 IN 2803 6 84 2 402 682 962 2242 223 2803 OUT 027 0 8 20 23 306 39 402 424 027 IN 436 907 36 84 2268 2722 37 3629 4082 436 OUT 784 7 236 342 3927 472 498 6283 7069 784 IN 747 429 244 289 374 4288 003 78 6432 747 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm 2 ) (N) 24
Series Weights Slide Bearing: M6 to 0 Standard stroke 2 0 7 0 2 7 200 20 300 30 400 6 0.46 0.62 0.74 0.83.02..9.28.46 20 0.77.02.2.3.49.63.77.9 2. 2.83 3. 3.39 2.06.43.68.84 2.0 2.8 2.3 2.2 3.0 3.84 4.8 4. 32.66 2.06 2.42 2.6 2.88 3. 3.34 3.7.07.3.99 6.46 40.9 2.40 2.79 3.06 3.33 3.9 3.86 4.3.7 6.2 6.78 7.32 0 3.26 3.96 4. 4.96.36.76 6.6 6.6 9.03 9.83.63.43 63 4. 4.90.8 6.07 6.6 7.0 7.4 8.04.68.66 2.64 3.63 80 7.47 8.3 8.9 9...7.3.04 6.24 7.44 8.6 0 2. 3.37 4.24..98 6.8 7.72 22.88 24.62 26.36 28. Ball Bushing: L6 to 0, High Precision Ball Bushing: 6 to 0 Standard stroke 2 0 7 0 2 7 200 20 300 30 400 6 0.48 0.8 0.66 0.83 0.94.02..9.36 20 0.82 0.97..3.0.63.76.89 2.33 2.9 2.84 3. 2.6.34.49.83 2.03 2.8 2.34 2.49 3. 3.4 3.72 4.02 32.8 2.00 2.29 2.67 2.9 3. 3.36 3.7 4.47 4.88.29.70 40.87 2.33 2.6 3.06 3.38 3.63 3.87 4..09.7 6.06 6.4 0 3. 3.8 4.30 4.92.42.79 6.7 6. 8.08 8.83 9.8.33 63 3.94 4.74.34 6.0 6.64 7. 7.8 8.0 9.77.7.6 2.9 80 7.6 8.3 8.9 9.46.02.7.3 3.99. 6.2 7.32 0 2.04 3.4 3.97 4.79.62 6.44 7.27 2.4 22.80 24.4 26. (kg) (kg) High Precision Ball Bushing/ Caution Positioning accuracy for pin hole on the plate Dispersion of dimensions when machining each component will be accumulated in the plate pin hole positioning accuracy when mounting this cylinder. Values below are referred as a guide. [Side mounting] Pin hole * = Catalog dimension ± (0. + L x 0.0008) [mm] *: To be 0. for, ø0 Note) Displacement by load and self-weight deflection by plate and guide rod are not included. [Bottom mounting] Pin hole L2 L B Pin hole B = ± (0.04 + L2 x 0.006) [mm] llowable Rotational Torque of Plate Torque: T(N m) Non-rotating ccuracy of Plate + θ θ 2 6 20 2 32 40 0 63 80 0 T(N m) Bearing Stroke type 2 0 7 0 2 7 200 20 300 30 400 M 0.3 0.84 0.69 0.8 0.0 0.44 0.40 0.36 0.30 L/.27 0.86 0.6 0.2 0.43 0.37 0.32 0.28 0.23 M 0.99 2.23.88.63.44.28.6.06 0.90 0.78 0.69 0.62 L/ 2.66.94.2.7.34.7.03 0.93 0.76 0.6 0.6 0.49 M.64 3. 2.96 2.7 2.26 2.02.83.67.42.24.09 0.98 L/ 4.08 3.02 2.38 2.4 2.0.78.8.4.6 0.98 0.8 0.74 M 6.3 6.64.69 4.97 4.42 3.98 3.6 3.3 2.84 2.48 2.20.98 L/.9.89. 6.99 6.34.79.33 4.93 4.29 3.78 3.38 3.04 M 7.00 7.32 6.27.48 4.87 4.38 3.98 3.6 3.3 2.74 2.43 2.9 L/ 6. 6.49.62 7.70 6.98 6.38.87.43 4.72 4.6 3.7 3.3 M 3.0 3.8 2.0.6 9.0 8.60 7.86 7.24 6.24.49 4.90 4.43 L/ 9.7.2 9.80 2.8.6.7 9.80 9. 7.9 7.02 6.26.63 M 4.7.6 3..9.7 9.69 8.86 8.6 7.04 6.9.2 4.99 L/.2 2..0 4.3 3.0.9.0.2 8.84 7.80 6.64 6.24 M 26.0 22.9 20. 8.6 7.0.6 4. 2.6.2.0 9. L/ 2.2 22.7 20.6 8.9 7.3 6.0 4.8 2.9.3.0 8.94 M 4.9 37. 33.8 30.9 28.4 26.2 24.4 2.4 9. 7.2.7 L/ 4.7 37.9 34.6 3.8 29.3 27.2 2.3 22. 9. 7.3. Non-rotating accuracy q when retracted and when no load is applied should be not more than the values shown in the table. Non-rotating accuracy q M L 6 ± 0.07 ± 0.0 20 2 ± 0.06 ± 0.04 32 40 ± 0.0 ± 0.03 0 63 ± 0.04 ± 0.03 80 0 ± 0.03 ± 0.03 ± 0.0
Compact Guide Cylinder With ir Cushion Series High Precision Ball Bushing/ Plate Displacement mount (Reference Values) Load from lateral direction 6 Plate displacement amount 0.4 0.3 0.3 0.2 0.2 0. 0. 6-20 6-6-0 6-7 6-0 Displacement 0.0 6-2 0 0 20 30 Load from lateral direction (N) 0, 63 Plate displacement amount 0.7 0.6 0. 0.4 0.3 0.2 0. 0 63-400 0 63-300 0 63-200 0 63-0 63-0 0 63-0 0 0 20 40 60 80 0 Load from lateral direction (N) With ir Cushion Basic Type 20 Plate displacement amount Plate displacement amount 0.7 0.6 0. 0.4 0.3 0.2 0. 2 20-400 20-300 20-200 20-20-0 20-2 0 0 20 40 60 Load from lateral direction (N) 0.7 0.6 0. 0.4 0.3 2-400 2-300 2-200 0.2 2-2-0 0. 2-0 0 0 20 40 60 80 Load from lateral direction (N) 80 Plate displacement amount Plate displacement amount 0.4 0.4 0.3 0.3 0.2 0.2 0. 0. 0.0 0 0.6 0. 0.4 0.3 0.2 0. 80-400 80-300 80-20 80-200 80-80-0 80-0 0 0 0 0 200 Load from lateral direction (N) 0-400 0-300 0-20 0-200 0-0-0 0-0 0 0 0 200 300 Load from lateral direction (N) uto Switch 32, 40 Plate displacement amount 0.8 0.7 0.6 0. 32 40-400 32 40-300 0.4 32 40-200 0.3 32 40-32 0.2 40-0 0. 32 40-0 0 0 20 40 60 80 0 Load from lateral direction (N) Note ) The guide rod and self-weight for the plate are not included in the above displacement values. Note 2) llowable rotating torque, and operating range when used as a lifter, are the same as those of the L series. 26
Selection Conditions With ir Cushion Series Model Selection Vertical Horizontal L L L L m m Mounting orientation m m Maximum speed (mm/s) 200 or less 400 200 or less 400 Graph (Slide bearing) (), (2) (3), (4) (), (6) (7), (8) Graph (Ball bushing) () to (9) () to (4) (9), (20) (2), (22) Selection xample (Vertical Mounting) Selection conditions Mounting: Vertical Bearing type: Ball bushing Stroke: 7 stroke Maximum speed: 200 mm/s Load mass: 7 kg ccentric distance: 70 mm Find the point of intersection for the load mass of 7 kg and the eccentric distance of 70 mm on graph (), based on vertical mounting, ball bushing, 7 mm stroke, and the speed of 200 mm/s. L2-7Z is selected. () 7 stroke or less, V = 200 mm/s or less 20 ø2 Selection xample 2 (Horizontal Mounting) Selection conditions Mounting: Horizontal Bearing type: Slide bearing Distance between plate and load center of gravity: 40 mm Maximum speed: 400 mm/s Load mass: 8 kg Stroke: 0 stroke Find the point of intersection for the load mass of 8 kg and 0 stroke on graph (7), based on horizontal mounting, slide bearing, the distance of 40 mm between the plate and load center of gravity, and the speed of 400 mm/s. M32-0Z is selected. (7) L = 0 mm, V = 400 mm/s 0 40 30 20 ø0, 63 ø2 ø0 ø0, 63 ø2 0 0 200 ccentric distance L 0. 20 2 26 0 0 200 400 Stroke When the maximum speed exceeds 200 mm/s, the allowable load mass is determined by multiplying the value shown in the graph at 400 mm/s by the coefficient listed in the table below. Maximum Up to 300 mm/s Up to 400 mm/s Up to 00 mm/s Coefficient.7 0.6 Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more. 27
Model Selection Series Vertical Mounting Slide Bearing Operating pressure 0.4 MPa Operating pressure 0. MPa or more M6 to 0 () 2 stroke, V = 200 mm/s or less (2) Over 2 stroke, V = 200 mm/s or less 300 200 0 0 ø0 ø63 ø0 ø2 300 200 0 0 ø0 ø63 ø0 ø2 With ir Cushion Basic Type uto Switch 0. 300 200 ø0 0 0 200 ccentric distance L 0. 0 0 200 300 200 ccentric distance L (3) 2 stroke, V = 400 mm/s (4) Over 2 stroke, V = 400 mm/s ø0 0 0 ø63 ø63 0 ø0 0 ø0 ø2 ø2 0. 0 0 200 0. 0 0 200 ccentric distance L ccentric distance L Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more. 28
Series Vertical Mounting Ball Bushing L6 to 2 20 20 Operating pressure 0.4 MPa Operating pressure 0. MPa or more () 7 stroke or less, V = 200 mm/s or less (6) Over 7 stroke, V = 200 mm/s or less ø2 ø2 0 0 200 ccentric distance L 0 0 200 ccentric distance L L32 to 63 (7) 2 stroke, V = 200 mm/s or less (8) Over 2 stroke, V = 200 mm/s or less 0 0 ø63 ø63 0 ø0 0 ø0 0 0 200 ccentric distance L 0 0 200 ccentric distance L L80/0 (9) V = 200 mm/s or less 300 200 ø0 0 0 0 0 200 ccentric distance L Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more. 29
Model Selection Series Vertical Mounting Ball Bushing L6 to 2 () 7 stroke or less, V = 400 mm/s () Over 7 stroke, V = 400 mm/s ø2 0 0 200 ccentric distance L ø2 0 0 200 ccentric distance L Operating pressure 0.4 MPa With ir Cushion Basic Type L32 to 63 (2) 2 stroke, V = 400 mm/s 0 ø63 (3) Over 2 stroke, V = 400 mm/s 0 ø63 uto Switch ø0 ø0 0 0 200 ccentric distance L 0 0 200 ccentric distance L L80/0 (4) V = 400 mm/s 300 200 0 0 ø0 0 0 200 ccentric distance L Use the Guide Cylinder Selection Software, when the eccentric distance is 200 mm or more. 30
Series Horizontal Mounting Slide Bearing M6 to 0 () L = 0 mm, V = 200 mm/s or less (6) L = 0 mm, V = 200 mm/s or less 0 40 30 20 ø0, 63, 40 ø2 ø0 ø0, 63, 40 ø2 0 40 30 20 ø0, 63, 40 ø2 ø0 ø0, 63, 40 ø2 0. 20 2 26 0 0 200 400 Stroke 0. 20 2 26 0 0 200 400 Stroke (7) L = 0 mm, V = 400 mm/s (8) L = 0 mm, V = 400 mm/s 0 40 30 20 ø0, 63 ø0 ø0, 63 0 40 30 20 ø0, 63, 40 ø0 ø0, 63 ø2 ø2 ø2 ø2 0. 20 2 26 0 0 200 400 Stroke 0. 20 2 26 0 0 200 400 Stroke 3
Model Selection Series Horizontal Mounting Ball Bushing (9) L = 0 mm, V = 200 mm/s or less (20) L = 0 mm, V = 200 mm/s or less L6 to 2 L6 to 2 ø2 ø2 ø2 ø2 With ir Cushion Basic Type 0. 20 0 7 76 200 400 L32 to 63 Stroke 30 30 ø0, 63 0. 20 0 7 76 200 400 L32 to 63 Stroke uto Switch 20 ø0, 63 20 ø0, 63 ø0, 63, 40, 40, 40 ø0, 63 ø0, 63, 40, 40, 40 20 2 26 0 7 76 200 400 20 2 26 0 7 76 200 400 Stroke Stroke L80/0 0 40 30 ø0 L80/0 0 40 30 ø0 20 20 20 0 0 200 400 Stroke 20 0 0 200 400 Stroke 32
Series Horizontal Mounting Ball Bushing (2) L = 0 mm, V = 400 mm/s (22) L = 0 mm, V = 400 mm/s L6 to 2 L6 to 2 8 ø2 ø2 8 ø2 ø2 0. 20 0 7 76 200 400 Stroke 0. 20 0 7 76 200 400 Stroke L32 to 63 30 30 L32 to 63 20 ø0, 63, 40 ø0, 63, 40 ø0, 63, 40 20 ø0, 63 ø0, 63, 40 ø0, 63, 40, 40 20 2 26 0 7 76 200 400 20 2 26 0 7 76 200 400 Stroke Stroke L80/0 L80/0 0 0 40 40 30 30 20 ø0 20 ø0 33 0 0 200 400 Stroke 0 0 200 400 Stroke
Model Selection Series Operating Range when Used as Stopper Bore Size to ø2/m6 to 2 (Slide Bearing) L 0 mm υ m L 0 mm υ m * When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with 2 stroke or less. Note 2) The L (Ball bushing) and the (High precision ball bushing) cannot be used as a stopper. M6 to 2 (Slide Bearing) Mass of transferred object: m (kg) 0 0 40 30 20 4 3 2 ø2 Transfer speed: υ (m/min) 20 30 40 0 With ir Cushion Basic Type uto Switch Bore Size to ø0/m32 to 0 (Slide Bearing) L 0 mm υ m L 0 mm * When selecting a model with a longer L dimension, be sure to choose a bore size which is sufficiently large. Caution Caution on handling Note ) When using as a stopper, select a model with 0 stroke or less. Note 2) The L (Ball bushing) and the (High precision ball bushing) cannot be used as a stopper. m υ M32 to 0 (Slide Bearing) Mass of transferred object: m (kg) 2000 00 00 400 300 200 0 0 40 30 ø0 ø63 ø0 20 30 40 0 Transfer speed: υ (m/min) * Refer to graphs () and (7) if line pressure is applied by a roller conveyor after the workpiece is stopped. 34
Series Construction (With ir Cushion)/Series M M o!!0!2 @7!6 @8!9!4 q @9!9 i y @9 @9 t r @6 @8 #0 u!2 @4 @ @ w e r r!9! @0 @3@2 ø63 or more to ø2 2 stroke Cushion valve section to ø2 0 stroke or more ø0 or more Component Parts No. Description Material Note Body luminum alloy Hard anodized 2 Piston luminum alloy Chromated 3 Piston B luminum alloy Chromated 4 Piston luminum alloy to ø0 Chromated Piston rod Stainless steel to ø2 Carbon steel to ø0 Hard chrome plating 6 Collar luminum alloy Chromated 7 Head cover luminum alloy Chromated 8 Guide rod Carbon steel Hard chrome plating 9 Plate Carbon steel Nickel plating Plate mounting bolt Carbon steel Nickel plating Guide bolt Carbon steel Nickel plating 2 Retaining ring Carbon tool steel Phosphate coated 3 Retaining ring Carbon tool steel Phosphate coated 4 Magnet Plug Carbon steel Hexagon socket head plug to ø0 Nickel plating 6 Slide bearing Bearing alloy 7 Ball bushing 8 Spacer luminum alloy 9 Cushion ring luminum alloy ø2 to ø0 nodized 20 Cushion valve to lectroless nickel plating ø0 to ø0 Chromated Cushion needle only lectroless nickel plating Component Parts No. Description Material Note 2 Gasket NBR 22 Gasket NBR 23 Retaining ring Carbon tool steel ø0, ø63 Phosphate coated 24 Steel ball Carbon steel to ø0 2 Plug Carbon steel ø63 to ø0 Nickel plating 26 * Piston seal NBR 27 * Rod seal NBR 28 * Cushion seal Urethane 29 * Gasket NBR 30 * Gasket B NBR Replacement Parts/Seal Kit Kit no. Contents 6 6-Z-PS 20 20-Z-PS Set of nos. above 2 2-Z-PS @6, @7, @8, 32 32-Z-PS @9, #0 40 40-Z-PS Kit no. Contents 0 0-Z-PS Set of nos. 63 63-Z-PS above 80 80-Z-PS @6, @7, @8, 0 0-Z-PS @9, #0 * Seal kit includes @6 to #0. Order the seal kit, based on each bore size. * Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-0 ( g) 3
Compact Guide Cylinder With ir Cushion Series Construction (With ir Cushion)/Series L L!3!7 With ir Cushion Basic Type ø0 or more 7 stroke or less uto Switch to ø63 7 stroke or less!8 to ø63 0 stroke or more, ø0 20 stroke or more 36
Series to ø2/m, L, (With ir Cushion) Z W WB øxh7 depth 6 Section XX details T-slot dimensions b X (Mounting hole position) a Section XX 4 x YY depth YL X±0.02 (Pin hole position) XB X øxh7 3 6 c e d a b c d e 6 4.4 7.4 3.7 2. 6.7 20.4 8.4 4. 2.8 7.8 2.4 8.4 4. 3 8.2 Bottom view 4 x NN through Section XX Z W 2 x Cushion valve (Width across flats.) 4 x øo through 4 x øob counterbore depth OL L 4 x MM depth ML Section XX T R X±0.02 ødb ød PW X U X±0.02 (OL) H: T-slot for hexagon bolt VB V H øxh7 depth 6 Q S F G P + Stroke FB C + Stroke B + Stroke + Stroke 2 x P GB 2 x P (Plug) J PB K G T-slot øxh7 depth 6 * The use of a slot (width X, length XB, depth 3) allows for a relaxed pin pitch tolerance, with the pin hole (øxh7, depth 6) as the reference, without affecting mounting accuracy. * For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Strokes on page 24. * For bore size, only M x 0.8 port is available. * For bore size or more, choice of Rc, NPT, G port is available. (Refer to page 23.) M, L Common Dimensions Standard stroke P B C D F FB G G GB H H J K L MM ML NN O OB OL Nil TN TF 6 2, 0, 7, 0, 2,, 7, 200, 20 7 8 8 7 6 30. 7. 64 M4 22 M x 0.8 2 M x 0.8 4.3 8 4. M x 0.8 20 2, 0, 7, 0, 2,, 7 78 62 8 8 36. 9 83 M 8 8 24 M x 0.8 3 M x 0.8.4 9.. Rc/8 NPT/8 G/8 2 200, 20, 300, 30, 400 78. 62. 9 7 42. 93 M 2 2 30 M6 x.0 M6 x.0.4 9.. Rc/8 NPT/8 G/8 W WB P PB PW Q R S T U V VB 7 st or less 0 to 7 st 200, 20 st 300 st or more 7 st or less 0 to 7 st 200, 20 st 300 st or more X X XB YY YL Z 6 39. 9 6 4 2 62 46 6 38 44 200 27 60 24 3 3. M x 0.8 20 38.. 2 8 70 30 8 4 72 44 44 20 200 300 39 77 7 67 28 3 3. M6 x.0 2 7 2 37. 3. 30 26 78 38 9 64 82 0 44 20 200 300 39 77 7 67 34 4 4. M6 x.0 2 7 M (Slide bearing)/, DB, Dimensions DB 2 to 0 st 2 to 200 st 20 st or more 2 to 0 st 2 to 200 st 20 st or more 6 7 92. 92. 0 2. 2. 20 78 78 2 0 0 32 2 78. 78. 9. 6 0 0 3 37 L (Ball bushing) (High precision ball bushing)/, DB, Dimensions DB 2 to 7 st 0 to 200 st 20 st or more 2 to 7 st 0 to 200 st 20 st or more 6 7 94. 94. 8 0 23. 23. 20 78 0 7. 0 22 39. 2 8. 0. 7. 3 3 22 39
Compact Guide Cylinder With ir Cushion Series to ø63/m, L, (With ir Cushion) X (Mounting hole position) Z WB Section XX 4 x YY depth YL W øxh7 depth XL X±0.02 (Pin hole position) Section XX details XB øxh7 X XC XL T-slot dimensions b c d e a a b c d e 32 6... 3. 9. 40 6... 4 0 8. 3. 7. 4. 3. 63 7.8 7 8. With ir Cushion Basic Type Bottom view T R 4 x NN through Section XX X±0.02 ød Z W 2 x Cushion valve (Width across flats CV) 4 x øo through 4 x øob counterbore depth OL PW X U X±0.02 (OL) L 4 x MM depth ML H: T-slot for hexagon bolt Section XX VB V H uto Switch øxh7 depth XL Q S ødb F FB G GB P + Stroke C + Stroke B + Stroke + Stroke 2 x P 2 x P (Plug) PB J G K T-slot øxh7 depth XL * The use of a slot (width X, length XB, depth XC) allows for a relaxed pin pitch tolerance, with the pin hole (øxh7, depth XL) as the reference, without affecting mounting accuracy. * For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Strokes on page 24. * Choice of Rc, NPT, G port is available. (Refer to page 23.) M, L Common Dimensions Standard stroke P B C CV D F FB G G GB H H J K L MM ML NN O OB OL Nil TN TF 32 2, 0, 7, 0 84. 62.. 4 2 48 2 9 2 M6 24 24 34 M8 x.2 20 M8 x.2 6.7 7. Rc/8 NPT/8 G/8 40 2,, 7 9 69. 4 2 4 2 20 M6 27 27 40 M8 x.2 20 M8 x.2 6.7 7. Rc/8 NPT/8 G/8 0 200, 20, 300 97 69 3 20 2 6 64 2 48 M8 32 32 46 M x. 22 M x. 8.6 4 9 Rc/4 NPT/4 G/4 63 30, 400 2 74 3 20 2 6 78. 3. 62 M 39 39 8 M x. 22 M x. 8.6 9 Rc/4 NPT/4 G/4 W WB P PB PW Q R S T U V VB X X XB XC XL YY YL Z 7 st or less 0 to 7 st 200, 20 st 300 st or more 7 st or less 0 to 7 st 200, 20 st 300 st or more 32 3. 6 3. 30 96 44 78 98 63 48 24 200 300 4 83 2 7 42 4 4. 3 6 M8 x.2 6 2 40 38 8 39. 30 4 44 8 86 6 72 48 24 200 300 46 84 22 72 0 4 4. 3 6 M8 x.2 6 22 0 34 2. 47 40 30 60 46 30 92 48 24 200 300 48 86 24 74 66 6 4 8 M x. 20 24 63 38 28 8 0 30 70 8 24 42 2 28 200 300 0 88 24 74 80 6 4 8 M x. 20 24 M (Slide bearing)/, DB, Dimensions DB 2 st 0 to 200 st 20 st or more 2 st 0 to 200 st 20 st or more 32 84. 93. 29. 20 0 9 4 40 9 93. 29. 20 0 2. 38. 0 97 9.. 2 0 2. 3. 63 2 9.. 2 0 7. 48. L (Ball bushing) (High precision ball bushing)/, DB, Dimensions DB 2 st 0, 7 st 0 to 200 st 20 st or more 2 st 0, 7 st 0 to 200 st 20 st or more 32 84. 96. 6. 38. 6 0 2 32 4 40 9 96. 6. 38. 6 0. 2. 47. 0 97 2. 32. 9. 20 0. 3. 62. 63 2 2. 32. 9. 20 0. 30. 7. 38
Series, ø0/m, L, (With ir Cushion) Z WB W ø6h7 depth Section XX details T-slot dimensions ø6h7 X (Mounting hole position) b a X±0.02 (Pin hole position) 6 7 c e a b c d e 80 3.3 20.3 2 8 22. 0.3 23.3 3. 30 d Section XX 4 x YY depth YL Bottom view 4 x NN through Section XX Z W 4 x øo through 4 x øob counterbore depth OL 2 x Cushion valve (Width across flats 3) L 4 x MM depth ML Section XX (OL) T R X±0.02 ødb ød PW X U X±0.02 2 x P (Plug) H: T-slot for hexagon bolt VB V H ø6h7 depth Q S F FB GC G P + Stroke C + Stroke B + Stroke + Stroke 2 x P GB JC JB PB J J G K T-slot ø6h7 depth * The use of a slot (width X6, length 7, depth ) allows for a relaxed pin pitch tolerance, with the pin hole (ø6h7, depth ) as the reference, without affecting mounting accuracy. * For intermediate strokes other than standard strokes, refer to Manufacture of Intermediate Strokes on page 24. * Choice of Rc, NPT, G port is available. (Refer to page 23.) M, L Common Dimensions Standard stroke P B C D F FB G G GB GC H H J J JB JC K L MM ML NN O OB OL Nil TN TF 80 0, 7, 0, 2,, 7 2. 8. 2 6 24 9. 9 6. 4. 202 M2 4. 38 7. 46 4 M2 x.7 2 M2 x.7.6 7. 3 Rc3/8 NPT3/8 G3/8 0 200, 20, 300, 30, 400 4 9 30 9 3. 22. 20. 8 240 M4. 4. 6 62 M4 x 2.0 3 M4 x 2.0 2. 20 8 Rc3/8 NPT3/8 G3/8 W WB P PB PW Q R S T U V VB 0, 7 st 0 to 7 st 200, 20 st 300 st or more 0, 7 st 0 to 7 st 200, 20 st 300 st or more X YY YL Z 80 39. 2. 74 2 74 7 98 6 80 40 2 28 200 300 4 92 28 78 0 M2 x.7 24 28 0 42. 32. 89 64 2 90 236 88 2 66 72 48 220 320 47 8 2 7 24 M4 x 2.0 28 M (Slide bearing)/, DB, Dimensions DB 0 to 200 st 20 st or more 0 to 200 st 20 st or more 80 3. 80. 30 9 0. 90. 36. 49. 39 L (Ball bushing) (High precision ball bushing)/, DB, Dimensions DB 0 to 200 st 20 st or more 0 to 200 st 20 st or more 80 8. 9. 2 37 70 0 78. 20. 30 37. 60.
Series uto Switch Mounting uto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting Height D-M9l/M9lV D-M9lW/M9lWV D-M9l/M9lV D-9l/9lV ø2 to ø0 uto switch D-P3DW ø2 to ø63 B, ø0 Ht With ir Cushion Basic Type B Hs uto Switch Proper Mounting Position pplicable Cylinder Series: uto switch model D-M9l D-M9lV D-M9lW D-M9lWV D-M9l D-M9lV D-9l D-9lV D-P3DW B B B 2 7. 9. 3.. 6.. 6. 6. 20 2. 2. 8. 8. 2. 4 7. 7 9. 32 2. 3 8. 9 8 8. 40. 6.. 2. 2 0 4. 7. 3 2. 63 6. 20 2. 6 2. 80 8 26 4 22 3. 2. 0 2. 32. 7. 28. 7 28 Note) djust the auto switch after confirming the operating conditions in the actual setting. uto Switch Proper Mounting Height uto switch model D-M9lV D-M9lWV D-M9lV D-9lV Hs D-P3DW Hs Ht Hs Ht Hs Ht 2 9. 7 6 22 9. 20 24. 22 2 26 24 32. 32 29 26. 3 40 33 30. 39 0 38. 36 44. 63 4. 43 9. 80 4 74 43 7. 48. 84 0 8. 3 83 8. 9 uto Switch uto Switch Proper Mounting Position pplicable Cylinder Series: - (With air cushion) uto D-M9l switch D-M9lV model D-M9lW D-9l D-P3DW D-M9lWV D-9lV D-M9l D-M9lV B B B 6 2 20. 2 6. 20 27 23 23 9 2 27 23 23 9 22. 8. 32 2 29 7 2 6. 24. 40 2. 3. 2. 27. 2 27 0 26 30. 22 26. 2. 26 63 30 3. 26 27. 2. 27 80 30. 38. 26. 34. 26 34 0 34. 44 30. 40 30 39. 40
Series Minimum Stroke for uto Switch Mounting uto switch model Number of auto switches ø2 ø2 ø0 ø63 ø0 D-M9lV D-M9 D-M9 W D-M9 WV D-M9 V D-M9 D-9 D-9 V D-P3DW pc. 2 pcs. pc. Note ) 2 pcs. Note ) pc. Note 2) 2 pcs. Note 2) pc. Note 2) 2 pcs. pc. Note 2) 2 pcs. Note 2) pc. Note ) 2 pcs. Note ) pc. 2 pcs. pc. 2 pcs. Note ) Confirm that it is possible to secure the minimum bending radius of mm of the auto switch lead wire before use. Note 2) Confirm that it is possible to securely set the auto switch(es) within the range of indicator green light ON range before use. For in-line entry type, also consider Note ) shown above. Note 3) The D-P3DW is mountable on bore size ø2 to ø0. Operating Range uto switch model 2 6 20 2 32 40 0 63 80 0 D-M9 /M9 V D-M9 W/M9 WV 3. 6 6 6 6. 6 7 D-M9 /M9 V D-9 /9 V 7 9 9 9 9. 9. 9... D-P3DW 6 6 6 6 6 7 * Values which include hysteresis are for guideline purposes only, they are not a guarantee (assuming approximately ±30% dispersion) and may change substantially depending on the ambient environment. Other than the applicable auto switches listed in How to Order, the following auto switches are mountable. Refer to the WB catalog or the Best Pneumatics No. 3 for the detailed specifications. Type Model lectrical entry Features Solid state D-P4DW Grommet (In-line) * With pre-wired connector is also available for solid state auto switches. For details, refer to the WB catalog or the Best Pneumatics No. 3. * Normally closed (NC = b contact) solid state auto switches (D-F9G/F9H) are also available. For details, refer to the WB catalog or the Best Pneumatics No. 3. * When installing the D-P4DW, use the BMG7-032 auto switch mounting bracket. Magnetic field resistant (2-color display) : to ø0 4
uto Switch Mounting Series uto Switch Mounting Brackets/Part No. pplicable Cylinder Series: M, L,, M-, L-, - pplicable auto switches D-M9l/M9lV D-M9lW/M9lWV D-M9l/M9lV D-9l/9lV D-P3DW ø2 to ø0 ø2 to ø0 Surfaces with auto switch mounting slot Surfaces with auto switch mounting slot uto switch mounting surfaces With ir Cushion Basic Type uto switch mounting screw q Insert the mounting bracket into the mating groove of the cylinder tube. w Check the detecting position of the auto switch and fix the auto switch firmly with the hexagon socket head cap screw (M2. x 2 L). * e If the detecting position is changed, go back to step q. uto Switch uto switch Note ) nsure that the auto switch is covered with the mating groove to protect the auto switch. Note 2) The tightening torque for the hexagon socket head cap screw (M2. x 2 L) is 0.2 to 0.3 N m. Mounting of auto switch When tightening the auto switch mounting screw, use a watchmakers screwdriver with a handle to 6 mm in diameter. Tightening Torque for uto Switch Mounting Screw (N m) uto switch model Tightening torque D-M9l(V) D-M9lW(V) 0.0 to 0. D-M9l(V) D-9l(V) 0. to 0.20 Hexagon socket head cap screw (Included with auto switch) (M2. x 2 L) Note) uto switch mounting brackets and auto switches are enclosed with the cylinder for shipment. For an environment that needs the water-resistant auto switch, select the D-M9l(V) type. 42
Prior to Use uto Switch Connection and xample Sink Input Specifications Source Input Specifications 3-wire, NPN Brown Input 3-wire, PNP Brown Input uto switch Black uto switch Black Blue COM (PLC internal circuit) Blue COM (PLC internal circuit) 2-wire Brown Input 2-wire Brown COM uto switch uto switch Blue Blue COM Input (PLC internal circuit) (PLC internal circuit) Connect according to the applicable PLC input specifications, as the connection method will vary depending on the PLC input specifications. xample of ND (Series) and OR (Parallel) Connection * When using solid state auto switches, ensure the application is set up so the signals for the first 0 ms are invalid. 3-wire ND connection for NPN output (Using relays) (Performed with auto switches only) Brown Relay Brown Load Black uto switch uto switch Black Load Blue Blue 3-wire OR connection for NPN output Brown Black Load uto switch Blue Brown Brown Brown uto switch 2 Black uto switch 2 Black uto switch 2 Black Blue Blue Blue 3-wire ND connection for PNP output (Using relays) Brown Relay Black uto switch Blue Brown (Performed with auto switches only) Brown Black uto switch Blue Brown 3-wire OR connection for PNP output Brown Black uto switch Blue Brown uto switch 2 Black Blue Load uto switch 2 Black Load Blue uto switch 2 Black Blue Load 2-wire ND connection uto switch uto switch 2 Brown Blue Brown Blue Load When two auto switches are connected in series, a load may malfunction because the load voltage will decline when in the ON state. The indicator lights will light up when both of the auto switches are in the ON state. uto switches with load voltage less than 20 V cannot be used. Load voltage at ON = Power supply voltage Residual voltage x 2 pcs. = 24 V 4 V x 2 pcs. = 6 V xample: Power supply is 24 VDC Internal voltage drop in auto switch is 4 V. 43 2-wire OR connection uto switch uto switch 2 Brown Blue Brown Blue Load (Solid state) When two auto switches are connected in parallel, malfunction may occur because the load voltage will increase when in the OFF state. Load voltage at OFF = Leakage current x 2 pcs. x Load impedance = m x 2 pcs. x 3 kw = 6 V xample: Load impedance is 3 kw. Leakage current from auto switch is m. (Reed) Because there is no current leakage, the load voltage will not increase when turned OFF. However, depending on the number of auto switches in the ON state, the indicator lights may sometimes grow dim or not light up, due to the dispersion and reduction of the current flowing to the auto switches.
Series Simple Specials/ Please contact SMC for detailed specifications, delivery and prices. Simple Specials Symbol -Xl -XC79 Specifications Change of guide rod end shape Tapped hole, drilled hole, pinned hole machined additionally Symbol -XB6 The following special specifications can be ordered as a simplified Made-to-Order. There is a specification sheet available on paper and CD-ROM. Please contact your SMC sales representatives if necessary. Specifications Heat resistant cylinder ( to C) Slide bearing Basic type Ball bushing High precision ball bushing Slide bearing With air cushion Ball bushing High precision ball bushing M L M L Slide bearing Basic type Ball bushing High precision ball bushing Slide bearing With air cushion Ball bushing High precision ball bushing M L M L Page Page 4 Page 46 Page Page 47 With ir Cushion Basic Type -XB Intermediate stroke (Using exclusive body) Page 47 -XB3 Low speed cylinder ( to 0 mm/s) Page 48 -XC4 -XC6 -XC8 -XC9 With heavy duty scraper Made of stainless steel djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Page 49 Page 0 Page 0 Page uto Switch -XC9 Intermediate stroke (Spacer type) Page 2 -XC22 Fluororubber seal Page 2 -XC3 -XC82 -XC8 -X44 With coil scraper Bottom mounting type Grease for food processing equipment Symmetrical port position Page 3 Page 4 Page 4 Page -X867 Side porting type (Plug location changed) Page 44
Series Simple Specials These changes are dealt with Simple Specials System. For details, refer to the WB catalog or the Best Pneumatics No. 3. Change of Guide Rod nd Shape Symbol -X/6/7/2 pplicable Series Series Model ction Symbol for change of rod end shape -Z Standard type M Double acting X, 6, 7, 2 L Double acting X, 6 Double acting Overall length of cylinder Fig. () X, X6 Precautions nsure that the cylinder s overall length should not exceed the allowable overall length. In the case of exceeding the allowable overall length, it will be available as specials. In Fig. (), (2) below, dimension cannot make it into dimension or less of the standard products. Confirm by referring to catalog. SMC will make appropriate arrangements if no dimension, tolerance, or finish instructions are given in the diagram. * dimension should be the guide rod diameter (D) 2 mm. In the case that the preferred dimension is different, fill in that dimension. Overall length of cylinder Fig. (2) X7, X2 llowable overall length of cylinder 2,6 34 20 to 32 40 40 to 63 6 80,0 603 Guide Rod nd Shape Pattern -X -X6 L MM C0. C0. (Standard body dimensions) (Standard body dimensions) -X7 -X2 MM D MM (Standard body dimensions) 30 (Standard body dimensions) 30 T 4
Simple Specials Series 2 Tapped Hole, Drilled Hole, Pinned Hole Machined dditionally Symbol -XC79 This simple special is meant for machining additionally tapped hole, drilled hole, and pinned hole, as requested from customer, on parts designed largely for mounting a workpiece etc. in the combined air cylinders. But, for each model, since they have the portions which are impossible to machine additionally, refer to the additional machining limitation. pplicable Series -Z Series Model ction Standard type With air cushion M L M L Double acting Double acting Double acting Double acting Double acting Double acting Component parts applicable for additional machining Plate Precautions We cannot take any responsibility as for the intensity of holes machined additionally and the effects of decreased intensity for the product itself. It will not be plated again for the machined part additionally. Be sure to fill in through for through-hole, and effective depth for blind hole. When using by machining through-hole additionally, ensure that the tip of the bolt etc. for mounting workpiece should not stick into the cylinder side. It may result in an unexpected problem. Use caution not to interfere the existing mounting hole on the standard products with the hole to be machined additionally. But it is possible to drill additionally the larger size of hole at the same position as the existing hole. With ir Cushion Basic Type Common Complementary xplanation/holes which can be additionally machined are the following 3 types. Tapped hole Drilled hole Pinned hole Designated nominal diameter and tapped hole of a pitch are machined additionally. (Maximum nominal thread diameter M20) Blind hole is deep into the bottom of prepared hole which sums up to C in the figure below in contrast to the effective depth of tapped hole. When there is a condition which does not allow through-hole etc., leave sufficient thickness in the inner part of hole. Drilled hole of a designated internal diameter is machined. (Maximum hole diameter 20 mm) If you wish for blind hole, instruct us with effective depth. (Refer to the figure below.) Besides, dimensional accuracy for internal diameter will be ±0.2 mm. Pinned hole of a designated diameter (reamer hole) is machined. (Maximum hole diameter 20 mm) Internal dimension tolerates H7 tolerance to the designated hole diameter. (Refer to the table below.) Hole dia. 3 or less Over 3 to 6 Over 6 to Over to 8 Over 8 to 20 Tolerance +0.0 0 +0.02 0 +0.0 0 +0.08 0 +0.02 0 uto Switch D (Thread size) (ffective thread depth) B = 3 x P (Incomplete thread section) D (ffective depth) DH7 (ffective depth) C = 0.3 x (D P) C = 0.3D Note) P stands for thread pitch. Limitation for Machining dditionally/since the slanted lines denote the restricted range for machining additionally, design the dimensions, referring to below. Plate material: Steel Mounting side C (Reference) Top connecting port side B Dimensional Range Not Possible to Machine dditionally B C 2 8 4 6 3 46 20 2 4 2 4 2 64 32 2 2 78 40 2 2 86 0 30 30 63 30 30 24 80 34 34 6 0 42 42 88 46
Series Please contact SMC for detailed dimensions, specifications and lead times. Heat Resistant Cylinder ( to C) ir cylinder which changed the seal material and grease, so that it could be used even at higher temperature up to from C. Symbol -XB6 pplicable Series Series Model ction -Z Standard type M Double acting Note ) Operate without lubrication from a pneumatic system lubricator. Note 2) Please contact SMC for details on the maintenance intervals for this cylinder, which differ from those of the standard cylinder. Note 3) In principle, it is impossible to make built-in magnet type and the one with auto switch. But, as for the one with auto switch, and the heat resistant cylinder with heat resistant auto switch, since it will be differed depending on the series, please contact SMC. Note 4) Piston speed is ranged from 0 to 00 mm/s. But, for and ø0, it will be 0 to 400 mm/s. Note ) No cushion is equipped. Check the kinetic energy. How to Order M Standard model no. Warning Precautions Heat resistant cylinder XB6 Be aware that smoking cigarettes etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. Specifications mbient temperature range C to C Seal material Grease Specifications other than above Dimensions ød Fluororubber Heat resistant grease Same as standard type D 2 (6) 6 (8) 20 () 2 () 32 (4) 40 (4) 0 20 63 20 80 2 0 30 The dimensions in ( ) are the same as standard type. 2 Intermediate Stroke (Using exclusive body) Symbol -XB Cylinder which can reduce the mounting space by using an exclusive body which does not use a spacer to achieve that the full length dimension could be shortened when an intermediate stroke other than the standard stroke is required. pplicable Series Series Model ction M Double acting -Z Standard type L Double acting Double acting How to Order M L Standard model no. XB Intermediate stroke Specifications: Same as standard type 47
Series 2 Intermediate Stroke (Using exclusive body) Dimensions WB W + Stroke Stroke Range Stroke range 2, 6 to 249 20, 2 2 to 399 32, 40, 0 63, 80, 0 26 to 399 * Specifications except the stroke range are the same as standard. Note) pplicable stroke available by the mm interval. Symbol -XB M, L, /W, WB Dimensions Stroke range W WB to 39 st 4 to 99 st to 99 st 20 to 249 st to 39 st 4 to 99 st to 99 st 20 to 249 st 2 20 40 200 2 60 to 249 6 24 44 200 7 27 60 Stroke range W WB 2 to 39 st 4 to 24 st 26 to 99 st 20 to 299 st 30 to 399 st 2 to 39 st 4 to 24 st 26 to 99 st 20 to 299 st 30 to 399 st 20 24 44 20 200 300 29 39 77 7 67 2 to 399 2 24 44 20 200 300 29 39 77 7 67 Stroke range W WB 26 to 49 st to 24 st 26 to 99 st 20 to 299 st 30 to 399 st 26 to 49 st to 24 st 26 to 99 st 20 to 299 st 30 to 399 st 32 24 48 24 200 300 33 4 83 2 7 40 24 48 24 200 300 34 46 84 22 72 0 24 48 24 200 300 36 48 86 24 74 26 to 399 63 28 2 28 200 300 38 0 88 24 74 80 28 2 28 200 300 42 4 92 28 78 0 48 72 48 220 320 3 47 8 2 7 With ir Cushion Basic Type M/, Dimensions to 74 st 76 to 99 st to 249 st to 74 st 76 to 99 st to 249 st 2 42 60. 82. 0 8. 40. 6 46 64. 92. 0 8. 46. 2 to 74 st 76 to 99 st 20 to 399 st 2 to 74 st 76 to 99 st 20 to 399 st 20 3 77. 0 24. 7 2 3. 77. 9. 0 24 6 26 to 74 st 76 to 99 st 20 to 399 st 26 to 74 st 76 to 99 st 20 to 399 st 32 7 93. 29.. 34 70 40 7 93. 29. 9 27. 63. 0 88. 9.. 6. 37. 78. 63 88. 9... 32. 73. 80 4. 3. 80. 8 3 84 0 26.. 90.. 3. 74. * Dimensions except mentioned above are the same as standard type. L, /, Dimensions to 39 st 4 to 99 st to 249 st to 39 st 4 to 99 st to 249 st 2 43 84. 3 42. 6 49 6 94. 3 9 48. 2 to 39 st 4 to 24 st 26 to 99 st 20 to 399 st 2 to 39 st 4 to 24 st 26 to 99 st 20 to 399 st 20 9 76 0 7. 6 23 47 64. 2 6. 8. 0. 7. 2 28 47 64 26 to 74 st 76 to 24 st 26 to 99 st 20 to 399 st 26 to 74 st 76 to 24 st 26 to 99 st 20 to 399 st 32 79. 96. 6. 38. 20 37 7 79 40 79. 96. 6. 38. 3. 30. 0. 72. 0 9. 2. 32. 9. 9. 40. 60. 87. 63 9. 2. 32. 9. 4. 3.. 82. 26 to 49 st to 74 st 76 to 99 st 20 to 399 st 26 to 49 st to 74 st 76 to 99 st 20 to 399 st 80 4. 28. 8. 9. 8 32 62 9 0 9. 4. 78. 20. 3. 29. 62. 8. uto Switch 3 Low Speed Cylinder ( to 0 mm/s) ven if driving at lower speeds to 0 mm/s, there would be no stick-slip phenomenon and it can run smoothly. Symbol -XB3 pplicable Series Series Model ction -Z Standard type M Double acting L Double acting How to Order M L Standard model no. XB3 Low speed cylinder Specifications Piston speed Dimensions to 0 mm/s Same as standard type Specifications other than above Same as standard type Note ) Operate without lubrication from a pneumatic system lubricator. Note 2) For the speed adjustment, use speed controllers for controlling at lower speeds. (Series S-FM/S-M) Warning Precautions Be aware that smoking cigarettes etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. 48
Series 4 With Heavy Duty Scraper Symbol -XC4 It is suitable for using cylinders under the environment, where there are much dusts in a surrounding area by using a heavy duty scraper on the wiper ring, or using cylinders under earth and sand exposed to the die-casted equipment, construction machinery, or industrial vehicles. pplicable Series Series Model ction M Double acting -Z Standard type L Double acting Double acting How to Order M L Standard model no. XC4 With heavy duty scraper Suffix Nil With scraper on single side W With scrapers on both sides Specifications pplicable series M L/ Bearing type Slide bearing Ball bushing 20, 2, 32, 40, 0, 63, 80, 0 Minimum operating On single side 0.2 MPa pressure On both sides 0.4 MPa Specifications other than above Same as standard type Caution Do not replace heavy duty scrapers. Since heavy duty scrapers are press-fit, they must be replaced together with the holder plate assembly. Dimensions (Dimensions other than below are the same as standard type.) HT ød (Piston rod O.D.) FC FB B + Stroke + Stroke ød (Piston rod O.D.) FD W + 2 x Stroke øds 4 x ømt W + Stroke cylinder with scrapers on both sides M, L, Common Dimensions FC B D FB M 20 63 () 8 9 2 63. () 7 9 32 69. (4) 22 9 40 76 (4) 22 9 0 82 20 26 8 63 87 20 26 80 6. 2 34 6 0 26 30 4 6 The dimensions in ( ) are the same as standard type. L With Scrapers on Both Sides/W, W, FD, MT, DS Dimensions DS W W FD MT M L 20 74 6 6 7 2 74. 6 7 2 9 32 82. 7 6 8. 26 2 40 89 7 6 8. 26 2 0 9 7 6 3 26 63 0 7 6 3 26 80 20. 8 6 4 36 3 0 43 8 9 6 44 36 * Bypass port for guide rod with bottom mounting M (Slide bearing)/,, HT Dimensions L, (Ball bushing)/,, HT Dimensions Over 0 st Over 0 st HT Over 30 st Over 0 st Over 30 st Over 0 st HT 0 st or less to 200 st Over 200 st 0 st or less to 200 st Over 200 st 30 st or less to 0 st to 200 st Over 200 st 30 st or less to 0 st to 200 st Over 200 st 20 69 86 27. 6 23 47 64. 80 2 7. 9.. 27. 2 28 47 64 93 20 63 87. 20 0 24. 7 80 2 63. 87. 9. 0 24 6 93 32 8 3. 39.. 34 70. 40 8 3. 39. 9 27. 63. 9 0 98. 9. 60. 6. 37. 78. 63 98. 9. 60.. 32. 73. 6 80 4. 4. 90. 8 3 84 202 0 36. 6. 200.. 3. 74. 240 Over 0 st Over 0 st Over 0 st Over 0 st 0 st or less to 0 st to 200 st Over 200 st 0 st or less to 0 st to 200 st Over 200 st HT 32 89. 6. 26. 48. 20 37 7 79 40 89. 6. 26. 48. 3. 30. 0. 72. 8 0. 22. 42. 69. 9. 40. 60. 87. 46 63. 22. 42. 69. 4. 3.. 82. 60 49 Over 2 st Over 0 st Over 2 st Over 0 st 2 st or less to 0 st to 200 st Over 200 st 2 st or less to 0 st to 200 st Over 200 st HT 80 4. 38. 68. 20. 8 32 62 9 99 0 29.. 88. 2. 3. 29. 62. 8. 236
ød M ømg Series Made of Stainless Steel Suitable for the cases it is likely to generate rust by being immersed in the water and corrosion. pplicable Series Parts material changed to stainless steel Specifications other than above and external dimensions 6 -Z Specifications -Z Series Model ction qpiston rod wguide rod eplate Standard type rplate mounting bolt B yretaining ring q, w, e, r, t, y q, w, t, y Same as standard type thexagon socket head plug Series Model ction Standard type M L M L Double acting Double acting Double acting Double acting Double acting How to Order M L djustable Stroke Cylinder/djustable xtension Type ød B Dimensions Standard model no. D D 2 (6) 40 (4) 6 (8) 0 20 20 () 63 20 2 () 80 2 32 (4) 0 30 The dimensions in ( ) are the same as standard type. Stroke adjustment symbol B Stroke adjustment range 0 to 0 to 2 Specifications other than above Made of stainless steel Width across flats MC XC6 Suffix Stainless steel used on all standard iron parts Stainless steel used on rod parts etc. Symbol -XC6 Symbol -XC8 It adjusts the extending stroke by the stroke adjustable mechanism equipped in the head side. (fter the stroke is adjusted, with cushion on both sides is altered to single-sided, with cushion.) pplicable Series How to Order M L Stroke Stroke adjustment symbol Z XC8 Specifications Same as standard type MB Dimensions (Dimensions other than below are the same as standard type.) With ir Cushion Basic Type uto Switch Warning Symbol djustable stroke cylinder/djustable extension type Precautions. When the cylinder is operating, if something gets caught between the stopper bracket for adjusting the stroke and the cylinder body, it could cause bodily injury or damage the peripheral equipment. Therefore, take preventive measures as necessary, such as installing a protective cover. 2. To adjust the stroke, make sure to secure the wrench flats of the stopper bracket by a wrench etc. before loosening the lock nut. If the lock nut is loosened without securing the stopper bracket, be aware that the area that joins the load to the piston rod or the area in which the piston rod is joined with the load side and the stopper bracket side could loosen first. It may cause an accident or malfunction. djustable range (Piston rod O.D.) MT MP Stroke MK M, L, Common Dimensions MD ML + djustment MH + Stroke + djustment (: mm, B: 2 mm) D M MB MC MD ømg MH MK ML MP MT 2 ( 6) 27 3 8 M4 x 0.7 4 20. 3 3 6 ( 8) 28 6 M x 0.8 4 20. 3 3 20 () 33 22 2 M6 x 20 26 7 4 3 4 2 2 4 2 2 M6 x 20 27 7 4 3 32 6 32 7 M8 x.2 2 3 9 8. 4 6 40 6 60 32 9 M x.2 2 3 7 4 6 0 20 7 38 24 M4 x. 3 46 3 2 4 8 63 20 84 0 24 M4 x. 3 46 3 2 4 8 80 2 4 0 32 M20 x. 4 6 30 4 9 0 30 40 6 32 M20 x. 4 8 6 30 4 2 The dimensions in ( ) are the same as standard type. 0
Series 7 djustable Stroke Cylinder/djustable Retraction Type The retract stroke of the cylinder can be adjusted by the adjustment bolt. Symbol -XC9 pplicable Series Series Model ction M Double acting -Z Standard type L Double acting Double acting Specifications Stroke adjustment symbol B Stroke adjustment range 0 to 0 to 2 Specifications other than above Same as standard type How to Order M L Stroke Stroke adjustment symbol Z XC9 djustable stroke cylinder/djustable retraction type Dimensions (Dimensions other than below are the same as standard type.) MB (Width across flats) BM (djustment bolt) Caution Precautions. When air is supplied to the cylinder, if the stroke adjustment bolt is loosened in excess of the allowable stroke adjustment amount, be aware that the stroke adjustment bolt could fly out or air could be discharged, which could injure personnel or damage the peripheral equipment. 2. djust the stroke when the cylinder is not pressurized. If it is adjusted in the pressurized state, the seal of the adjustment section could become deformed, leading to air leakage. Symbol djustable range M ømc MH + djustment (: mm, B: 2 mm) M, L, Common Dimensions BM M MB MC MH 2 M x 0.8 8 2. 7 6 M6 x 4 9 20 M8 x.2 6. 3 6 2 2 M8 x.2 6. 3 6 24 32 M8 x.2 6. 9 2 2 40 M2 x. 9 27 30 32. 0 M2 x. 9 30 34 32. 63 M6 x. 36 40 37 80 M20 x. 4 46 48. 0 M24 x. 8 46 2.
Series 8 Intermediate Stroke (Spacer type) Dealing with the intermediate stroke by installing a spacer with the standard stroke cylinder. pplicable Series -Z How to Order M L Series Model ction With air cushion Standard model no. M L Intermediate stroke (Spacer type) Double acting Double acting Double acting XC9 pplicable Stroke Description Model no. pplicable stroke xample Symbol -XC9 Dealing with the stroke by the mm interval by changing a collar of the standard stroke cylinder. Minimum manufacturable stroke to ø63: mm, ø0: 20 mm Select a rubber bumper type, because the cushion effect is not obtainable for less than this stroke. dd -XC9 to the end of standard part number. to 249 to ø63 to 399, ø0 20 to 399 Part no.: M20-3Z-XC9 mm width collar is installed in M20-0Z. C dimension is 2 mm. Note) Intermediate strokes (by the mm interval) with a special body are available as special products. With ir Cushion Basic Type 9 Fluororubber Seal pplicable Series Series Model ction Dimensions Symbol -XC22 uto Switch -Z Standard type M Double acting How to Order M Specifications Seal material mbient temperature range Standard model no. Specifications other than above Fluororubber seal XC22 Fluororubber With auto switch Note ) : C to 60 C (No freezing) Same as standard type Note ) Please confirm with SMC, as the type of chemical and the operating temperature may not allow the use of this product. Note 2) No cushion is equipped. Check the kinetic energy. ød D 2 (6) 6 (8) 20 () 2 () D 40 (4) 0 20 63 20 80 2 32 (4) 0 30 The dimensions in ( ) are the same as standard type. 2
Series HT ød (Piston rod O.D.) 4 x ømt ød With Coil Scraper It gets rid of frost, ice, weld spatter, cutting chips adhered to the piston rod, and protects the seals etc. Symbol -XC3 pplicable Series -Z How to Order M L Series Model ction M Double acting Standard type L Double acting Double acting Standard model no. XC3 Specifications pplicable series M L/ Bearing type Slide bearing Ball bushing 20, 2, 32, 40, 0, 63, 80, 0 Minimum operating On single side 0.2 MPa pressure On both sides 0.4 MPa Specifications other than above Same as standard type With coil scraper Nil W Suffix With scraper on single side With scrapers on both sides Dimensions (Dimensions other than below are the same as standard type.) FC FB B + Stroke + Stroke (Piston rod O.D.) FD W + Stroke W + 2 x Stroke cylinder with scrapers on both sides M, L, Common Dimensions FC B D FB M 20 63 () 8 2 63. () 7 6 32 69. (4) 22 6 40 76 (4) 22 6 0 82 20 26 6 63 87 20 26 6 80 6. 2 34 8 6 0 26 30 4 9 6 The dimensions in ( ) are the same as standard type. M (Slide bearing)/,, HT Dimensions 3 0 st or less Over 0 st to 200 st Over 200 st 0 st or less Over 0 st to 200 st Over 200 st L 20 63 87. 20 0 24. 7 80 2 63. 87. 9. 0 24 6 93 32 8 3. 39.. 34 70 40 8 3. 39. 9 27. 63. 8 0 98. 9. 60. 6. 37. 78. 46 63 98. 9. 60.. 32. 73. 60 80 4. 4. 90. 8 3 84 99 0 36. 6. 200.. 3. 74. 236 HT With Scrapers on Both Sides/W, W, FD, MT Dimensions W W FD MT 20 74 6 6 2 74. 6 7 32 82. 7 6 9 40 89 7 6 8. 0 9 7 6 63 0 7 6 80 20. 8 6 4 0 43 8 9 6 L, (Ball bushing)/,, HT Dimensions 30 st Over 30 st Over 0 st Over 30 st Over 30 st Over 0 st Over or less to 0 st to 200 st 200 st or less to 0 st to 200 st 200 st HT 20 69 86 27. 6 23 47 64. 80 2 7. 9.. 27. 2 28 47 64 93 0 st or less Over 0 st to 0 st Over 0 st to 200 st Over 200 st 0 st or less Over 0 st to 0 st Over 0 st to 200 st Over 200 st 32 89. 6. 26. 48. 20 37 7 79 40 89. 6. 26. 48. 3. 30. 0. 72. 8 0. 22. 42. 69. 9. 40. 60. 87. 46 63. 22. 42. 69. 4. 3.. 82. 60 2 st or less Over 2 st to 0 st Over 0 st to 200 st Over 200 st 2 st or less Over 2 st to 0 st Over 0 st to 200 st Over 200 st 80 4. 38. 68. 20. 8 32 62 9 99 0 29.. 88. 2. 3. 29. 62. 8. 236 HT HT
ZZ Series Bottom Mounting Type Since the guide rod does not protrude from the bottom at the retraction of the rod, relief holes for guide rods are not required. pplicable Series Series Model ction -Z Standard type M Double acting How to Order M Bearing type M Slide bearing 2 2 mm 6 6 mm 20 20 mm 2 2 mm 32 32 mm 40 40 mm 0 0 mm 63 63 mm 80 80 mm 0 0 mm Stroke Z XC82 Bottom mounting type Cylinder stroke pplicable stroke 2 to 2 7, 0 32 to 0 2, 0, 7, 0 2 Grease for Food Processing quipment Food grade grease (certified by NSF-H) is used as lubricant. Same as the standard M- Z cylinder Guide rod Symbol -XC82 Cylinder mounting side Note) The total length (ZZ) of the guide rod bushing is shorter than the standard products. Symbol -XC8 With ir Cushion Basic Type uto Switch pplicable Series Series Model ction M Double acting Standard type L Double acting -Z Double acting M Double acting With air cushion L Double acting Double acting Specifications mbient temperature range 0 C to 60 C Seals material Nitrile rubber Grease Grease for food uto switch Mountable Dimensions Same as standard type Specifications other than above Same as standard type How to Order M L Warning Precautions Standard model no. Grease for food processing equipment XC8 Be aware that smoking cigarettes etc. after your hands have come into contact with the grease used in this cylinder can create a gas that is hazardous to humans. Splash zone Not installable Food zone Not installable Container Not installable zone Food zone n environment where food which will be sold as merchandize, directly touches the cylinder s components. Splash zone n environment where food which will not be sold as merchandize, directly touches the cylinder's components. Installable zone Non-food zone n environment where there is no contact with food. Food Non-food zone Installable Note ) void using this product in the food zone. (Refer to the figure on the right.) Note 2) When the product is used in an area of liquid splash, or a water resistant function is required for the product, please consult with SMC. Note 3) Operate without lubrication from a pneumatic system lubricator. Note 4) Use the following grease pack for the maintenance work. GR-H-0 (Grease: g) Note ) Please contact SMC for details about the maintenance intervals for this cylinder, which differ from those of the standard cylinder. 4