efore commencing assembly,please read these instructions thoroughly. Katana S 40 SFETY PRECUTIONS This radio control model is not a toy First-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent., ssemble this kit only in places out of children s reach Take enough safety precautions prior to operating this model., You are responsible for this models assembly and safe operation lways keep this instruction manual ready at hand for quick reference,even after completing the assembly. Could cause serious injury or even death SPECIFICTION Wing Span:1350 mm (53.1 in) Wing rea:35.7 dm (553.5sq.in) Total Length: 1370 mm (53.9 in) Engine : c 0.40 cu in Motor : Outrunner brushless motor Radio : 4 channels,5 servos
REQUIRED FOR OPERTION (Purchase separately) 1 minimum 4channel radio for airplanes (with 5servos). nd dry batteries. 4 Silicone Tube Fuel Filter CUTION: Only use a minimum 4channel radio for airplanes (No other radio may be used) 5 required for engine starting Glow engine fuel only. minimum 4 channel transmitter for airplanes. WRNING: Normal gasoline cannot be used with glow engines. 1 -size atteries Fuel Pump Plug Wrench For handing the radio properly.refer to its instruction manual. Engine and Muffler Model irplane engine Outrunner brushless motor c 0.40 cu in Muffler Glow plug 36 Glue 37 Other Instant glue equipment for enhancing airplane operation & perormance Epoxy Glue 3 Propeller splinner Purchase a propeller that will match your engine Engine Starter 1V attery (for starter) Ignition TOOLS REQUIRED ( Purchase separately) Sharp Hobby Knife Phillips Driver wl Needle Nose Pliers Wire Cutters Scissors 1 3... EFORE YOU EGIN Read through the manual before you begin,so you will have an overall idea of what to do. Check all parts.if you find any defective or missing parts.contact your local dealer. Symbols used throughout this instruction manual,comprise. pply epoxy glue. pply instant glue (C glue,super glue). mm Drill holes with the specified Diameter(here:mm) Ensure smooth non-binding movement while assembling. Must be purchased separately Pay close attention here Warning Do not overlook this symbol. ssemble left and right Sides the same way. Cut off shaded portion. Cut off excess.
ccessory list for this page. 3 Main wing X0mm Tp 8mm nylon Nut - - - - 4 1.8X85mm Rod 4x30mm nylon screw 4mm - - - - - -1 washer X485mm tube put the servo line into the fuselage Cut the film 1 Install the aileron 4 fter cut the film, insert the elevator into the slot - - - - - - 8 L R Install the aileron servo 5 Install the elevator Servo line X0mm Tp ileron servo 1.8X85mm Rod mmx4mm carbon stick - - - - 4 3
ccessory list for this page. 8 Install the tail wheel 3X3mm.1mm Nylon Collar.1mm Collar 3X1 Tp screw - - - - 3 - - - - 3 3X3mm.1mm Nylon Collar.1mm Collar 3X1 Tp screw - - - - 3 6 Horizontal/Vertical tail 9 Instal the rudder - - - - 3 mm Fold flection Diameter 7 Horizontal/Vertical tail 10 Install the main landing gear Securely glue together,if coming off during flights. You lose control of your airplane which leads to accidents 4
ccessory list for this page. 13 Instal the elevator servo X14mm Tp.3X8mm Tp screw 3X35mm screw 3X1mm screw - - - - - - 3 1.8X170mm Rod - - 1.8X1400mm Rod - - 3mm nut 3mm Washer - - - - - - 5 3.mm Collar 3X3mm screw - - Elevator servo 1.8X140mm Rod - - X10mm Tp - - 11 Install the main landing gear 14 Install the engine mount.3x8mm Tp screw 3X35mm screw 3X1mm screw - - - - - - 3 3mm nut 3mm Washer - - - - - - 5 3.mm Collar 3X3mm screw 1 Install the rudder servo 15 Install the engine mount Rudder servo 1.5 X14mm Tp 1.8X170mm Rod - - - - - - 1.5 5
18 ccessory list for this page. 3X18mm ----4 Linkage Stopper 1.4X430mm Rod -- mm Nut 3X3mm -- 3X0mm 3mm lind Nut Linkage Stopper mm ------4 16 ----4 ------4 3X5mm Install the engine 3X3mm Drill 4 holes and set blind nut in appropriate position in the firewall before install the engine. 19 -- ssembly of the full tank fter confirming the position(see front of fuel tank). Insert and tighten the screw. 4mm.5.5 10mm Nut 1.4X385mm Rod -- 3X0mm 4.mm Diameter (here:4.mm) 17 3X18mm ------4 3X5mm 0 Install the engine mount Motor : Outrunner rushless motor ----4 ----4 Install the motor 3mm lind Nut ------4 The motor must be purchased separately 6
ccessory list for this page. 3 Install the canopy 3X1mm Tp screw.3x10mm Tp screw 1 Radio Equipment 4 (attery) (Receiver) ssembly the cowling 5 53mm Spinner Propeller 3X1mm Tp screw.3x10mm Tp screw 7
6 djustment. 8 djustment djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ILERON Rudder Side view Side view Top view Top view 7 djustment. 9 djustment. djust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level. ELEVTOR Side view Never fly before checking the Cg s required position. In order to obtain the CG specified,reposition the receiver and battery. 90-95mm Top view CG Warning NEVER fly the model without well balancing. 8