Tri-Clover FV-00
Applications The Tri-Clover range of fractional valves has been designed for applications requiring a secure, sanitary or sterile environment within the food, beverage, pharmaceutical, cosmetic or biotechnology processing industries. The self draining ports and ease of operation make the Tri-Clover valve ideal for processes where an uncomprimising sanitary environment are demanded. For example: Processing equipment: stills, condensers, fermenters, heat exchangers, filters and strainers. Make-up and additional lines: for ph and steam in biotechnology systems. Pure water service: DI, RO pyrogen-free and other water treatment or processing operations. Laboratory / Pilot Plant: low volume research applications, small scale development products. The wide range of styles: manual shut-off, airactuated, relief, sample and check together with the available surface finish and elastomer options enable the processor to match the valve to the specific application. Standard Design, 650 Series Valves Body Styles Available: Manual shut-off Air-Actuated Relief Sample Check Port Connection Sizes: ¹ ₂ (12.7 mm) tube OD ³ ₄ (19 mm) tube OD Connection Type: Tri-Clamp Overview Materials of Construction: Valve body stainless steel 316L standard Bonnet stainless steel 316L standard Stem stainless steel 316L standard Finish Options: 20 Ra ID, glass beaded OD standard 20 Ra ID, 32 Ra OD option 15 Ra ID, 32 Ra OD option 15 Ra E/P ID, 32 Ra OD option 10 Ra E/P ID, 32 Ra OD option Elastomers: Fluoroelastomer EPDM (sulfur free) Buna standard option option General Service Ranges: Fractional sized valves are nominally rated up to 100 PSI (6.9 BAR)@250 F (121 C) or 230PSI (15.8 BAR)@72 F (22 C). Refer to section on Plug and Seat Design for further detail. Contact Tri-Clover if higher pressure or temperature ratings are called for. 3
Manual Shut-Off ¹ ₂ = 7 ¹ ₈ (181mm) ³ ₄ = 6 ¹ ₄ (159mm) ¹ ₂ = 7 (178mm) ³ ₄ = 6 (152mm) 1 ¹ ₂ 1 ¹ ₂ 1 ¹ ₂ Relief Valve 650-10M-R40 (tee body) 650-30M-R40 (cross body) 1 ¹ ₂ Manual Shut-Off Valve 650-10M-40 (tee body) 650-30M-40 (cross body) 24.4 Cv Factors for manual shut-off valve 21.3 18.3 Head Loss in Meters % Valve Stroke ¹ ₂ (12.7 mm) ³ ₄ (19 mm) 15.2 Operating area 10 1.1 1.4 20 1.6 2.6 30 1.9 3.7 40 2.1 4.9 50 2.2 6 60 2.3 7 70 2.4 7.8 80 2.45 8.8 90 2.5 9.1 100 2.6 9.2 Gal/Min. Ltr/Min. 5 10 15 20 75.7 25 30 35 113.6 132.5 18.4 37.8 56.8 94.6 Head Loss Curve Model 650 Shut-Off Valve... 3 /4 inch(19mm) 1 /2 inch (12.7mm) 12 9.1 6 3 4
Air-Actuated, Check & Sample Valves ¹ ₂ = 8 ³ ₄ (222mm) ³ ₄ = 8 ¹ ₂ (216mm) 10 & 30 20 & 30 Actuators: Field serviceable with optional microswitch or proximity switch. Actuator Material: Cylinder is type 316SS - satin finish Spring is Type 17-7PH-SS Piston is UHMW polyethylene O-Rings are fluoroelastomer - standard with other options available. 1 ¹ ₂ 1 ¹ ₂ Series 650 Air-Actuated Valve 650-30M-Actuator (cross body) 3 ¹ ₄ (83mm) Check Valve C45MP Actuator Specifications: Air pressure range is 50-60 PSI (3.5-4.1 BAR) Air volume required at 50 PSI Normally Closed 1 3 /4 cu. in. Normally Open 2 3 /4 cu. in. Effective operating area is 2.19 sq. inches Filtered air and a pressure regulator are recommended Lubricated air is not required Check Valve: Check valve is available with 316 SS ball or with PTFE plug/spring loaded [ 3 /4" - (19mm) size approx. 1.5 PSI (0.1 BAR) relief pressure on both plug and ball, 1 /2" - (12.7mm) size approx. 3 PSI (0.2 BAR)] C45MP (316SS Ball) for vertical application only. 3 ⁵ ₈ (92mm) 1 ¹ ₄ (32mm) Sample Valve Material: Manual valves furnished with durable UHMW polyethylene handle. Optional bronze handle available for pressures above 150 PSI (10 BAR) or temperatures above 150 F (66 C). 1 ³ ₈ (35mm) Series 660 Sample Valve 660-10-40 5
650 Series Plug and Seat Design Series 650 Manual and Air-Actuated Valves are available in two seat styles: Plug Design The Lip Seal: Our patented, economical one-piece plug has no o- rings to replace. Available in fluoroelastomer* for temperatures up to 250 F (121 C), or PTFE for temperatures up to 120 F (49 C), or where fluoroelastomer is incompatible with your product. The O-Ring Seal: PTFE material, with fluoroelastomer o-ring, is ideal where application calls for a PTFE plug, and the fluoroelastomer o-ring is acceptable. For temperatures up to 250 F (121 C). *Fluoroelastomer and PTFE lip seal not recommended for use in cross body valves (30M). Use only Type C (PTFE Plug with O-ring) in Type 30M valves. Tri-Clover carry U.S. Patent Number 4,570,665. 6
650 Series Air-Actuated Shut Off Valve Type 10 (Normally Open) Shut-Off Valve Holding Pressures- 50 psi Air Pressure Tube OD Size ¹ ₂" (12.7 mm) ³ ₄" (19 mm) Product Line Pressure (PSI) will close against (70 F) 230 (15.8 BAR) air pressure 195 (13.4 BAR) air pressure Type 20 (Normally Closed) Shut-Off Valve Holding Pressures (standard) Tube OD Size ¹ ₂" (12.7 mm) ³ ₄" (19 mm) Product Line Pressure (PSI) will close against (70 F) 150 (10.3 BAR) 100 (6.9 BAR) Type 30 (Air to Open - Air to Close) For applications requiring air both ways. No spring is used in the actuator. 7
655 Series Air-Actuated Divert Valve Port Connection Sizes: ¹ ₂ (12.7 mm) tube OD ³ ₄ (19 mm) tube OD Connection Type: Tri-Clamp Materials of Construction: Valve body stainless steel 316L standard Bonnet stainless steel 316L standard Stem stainless steel 316L standard Finish: 20 Ra ID, Glass Beaded OD standard 20 Ra ID, 32 Ra O option 15 Ra ID, 32 Ra OD option 15 Ra E/P ID, 32 Ra OD option 10 Ra E/P ID, 32 Ra OD option 655 Series Air-Actuated Divert Valve Actuators: Field serviceable with optional microswitch or proximity switch. Actuator Material: Cylinder is type 316SS - satin finish Spring is Type 17-7PH-SS Piston is UHMW polyethylene O-Rings are fluoroelastomer - standard with other options available. Actuator Specifications: Air pressure range is 50-60 PSI (3.5-4.1 BAR) Air-volume required at 50 PSI Normally Closed 1 3 /4 cu. in. Normally Open 2 3 /4 cu. in. Effective operating area is 2.19 sq. inches Filtered air and a pressure regulator are recommended Lubricated air is not required Elastomers: Fluoroelastomer EPDM Buna standard option option General Service Ranges: Fractional sized valves are nominally rated up to 100 PSI (6.9 BAR)@250 F (121 C) or 230PSI (15.8 BAR)@72 F (22 C). Refer to section on Plug and Seat Design for further detail. Contact Tri-Clover if higher pressure or temperature ratings are called for. 8
655 Series Air-Actuated Divert Valve Type 10 (Normally Open) Shut-Off Valve Holding Pressures- 50 psi Air Pressure Tube OD Size ¹ ₂" (12.7 mm) ³ ₄" (19 mm) Product Line Pressure (PSI) will close against (70 F) 230 (15.8 BAR) air pressure 195 (13.4 BAR) air pressure A C (Close C) (Close A) B Spring to Open (Type 10) Type 20 (Normally Closed) Shut-Off Valve Holding Pressures (standard) Tube OD Size Product Line Pressure (PSI) will close against (70 F) ¹ ₂" (12.7 mm) ³ ₄" (19 mm) 150 (10.3 BAR) 100 (6.9 BAR) A C B Spring to Close (Type 20) Type 30 (Air to Open - Air to Close) For applications requiring air both ways. No spring is used in the actuator. A C B Air to Air (Type 30) 9
655 Series Air-Actuated Divert Valve 15.2 13.7 12.2 10 & 30 10.7 9.1 7.6 Head Loss in Meters 9 9 16 (243mm) Extended 8 7 8 (222mm) 20 & 30 6.1 4.6 3.0 1.5 2 (51mm) 1 (25mm) Gal/Min. 5 10 15 20 25 30 35 Ltr/Min. 18.9 37.9 56.8 75.7 94.6 113.6 132.5 Head Loss Curve Model 655 Air-Actuated Divert Valve... 3 /4 inch (12.7 mm) 1 /2 inch (19 mm) 1 1 2 1 1 2 Air-Actuated Valve 655-21M-Actuator (tee body) 10
655 Series Plug and Seat Design Series 655 Air-Actuated Divert Valves are available with a bonded elastomer head. 655 Series Plug & Seat Design Molded Seat: Standard material is fluoroelastomer (seat option B) for temperatures up to 250 F (121 C). Other materials are available. Note: All elastomers used in Tri-Clover Fractional Valves are compounded to FDA standards. Optional Microswitch or Proximity Switch All Series 650 and 655 Air-Actuated valves can be furnished with optional microswitch or proximity switch-equipped actuators at an additional cost. Switches are designed to deliver a signal to indicate both the open and closed positions, via lights or panel readouts, to monitor valves or to act as a safety interlock in a total system. Microswitch units contain two SPDT switches, UL & CSA listings: 15 A/125 or 250 VAC, 1 /2 A, 125 VAC, 1 /4 A, 250 VAC. Low voltage, intrinsically safe microswitch units are also available. Proximity switches have no moving parts to be replaced, hence longer service life. Rate Range 20-140 Volt AC, 50-60 Hz, 10-140 Volt DC, Maximum Load 200 ma,.8ma Leakage Current. Contact Tri-Clover for additional details. 11
A sample part number for Air-Actuated Shut-Off Valves is shown below 650 Series Order Information VALVE SERIES 650= For shut-off or Manual Valves BODY STYLE 10M= Tee 30M= Cross PORT SIZE ¹ ₂ = ¹ ₂" Tube OD (12.7 mm) ³ ₄ = ³ ₄" Tube OD (19 mm) SEAT A = PTFE lip seal B = Fluoroelastomer lip seal C = PTFE plug with O-ring GASKET / O-RING MATERIAL Y = Fluoroelastomer (SFY) E = EPDM U = Buna ES = EPDM / Sulfur Free 650 30M 10 ¹ ₂ C U 316L PL ACTUATOR TYPE Manual 40Br = bronze (optional) 40= Shut-Off R40= Relief Air-Actuated No Switch Microswitch Proximity Switch (air to close / spring to open) 10 13 17 (air to open / spring to close) 20 23 27 (air both ways) 30 33 37 MATERIAL (Type 316L) Must be noted in part number as shown FINISH -- = 20 (0.5) Ra ID, Glass Beaded OD PL = 20 (0.5) Ra ID, 32 (0.8) Ra OD PM = 15 (0.4) Ra E/P ID, 32 (0.8) Ra OD PP = 15 (0.4) Ra ID, 32 (0.8) Ra OD PR = 10 (0.25) Ra E/P ID, 32 (0.8) Ra OD 660 Series Sample Valves Ordering Information Sample valves are available in 1 /2" (12.7 mm) Tri-Clamp connections on both ports, or with a ½" (12.7mm) Tri-Clamp lower port and a ¼" (6.3mm) hose barb side port. Available with a PTFE plug with O-ring only. Electropolished is optional. Order Part Number 660-10-40-1 /2-1 /4-C-316L or 660-10M-40-1 /2-1 /2-C-316L. 12
A sample part number for Air-Actuated Divert Valves is shown below 655 Series Order Information VALVE SERIES 655 = For Divert Valves 555 = Aseptic SEAT A = Buna plug B = Fluoroelastomer plug (std) C = EPDM plug D = EPDM sulfur free plug BODY STYLE 21M = Tee PORT SIZE ¹ ₂ = ¹ ₂" Tube OD (12.7 mm) ³ ₄ = ³ ₄" Tube OD ( 19 mm) GASKET / O-RING MATERIAL Y = Fluoroelastomer / SFY E = EPDM U = Buna ES = EPDM / Sulfur Free 655 21M 10 ¹ ₂ B U 316L PL MATERIAL Must be noted in part number as shown ACTUATOR TYPE Air-Actuated Microswitch Proximity Switch (air to close / spring to open) 10 13 17 (air to open / spring to close) 20 23 27 FINISH -- = 20 (0.5) Ra ID, Glass Beaded OD PL = 20 (90.5) Ra ID, 32 (0.8) Ra OD PM = 15 (0.4) Ra E/P ID, 32 (0.8) Ra OD PP = 15 (0.4) Ra ID, 32 (0.8) Ra OD PR = 10(0.25) Ra E/P ID, 32 (0.8) Ra OD (air both ways) 30 33 37 Check Valves Ordering Information Available in 1 /2" (12.7 mm) or 3 /4" (19 mm) port sizes in two check styles: C45MP size 316L = Type 316SS Ball C45MPS size 316L = PTFE Plug / Spring Loaded 13
Following are all registered trademarks of Tri-Clover: Tri-Clover Tri-Clamp Tri-Weld Tri-Taper Tri-Flo Valves Mix-Proof Catalog MPV Multiple actuator stem designs with full stroke capability. Air-Actuated Catalog AV Many styles for automatic flow, and full CIP capability. Also available with optional control top housing. 1"-4" (25.4-101.6mm) sizes. Fractional Sizes Bulletin FV Type 316L SS. ¹ ₂" & ³ ₄" (12.7 and 19.0mm) sizes. Ball Bulletin BV 3-piece body with PTFE seats and packing. 1"-4" (25.4-101.6mm) sizes. Butterfly Bulletin BFV Aluminum body. Adaptable to a variety of end connections. 1"- 4" (25.4-101.6mm) sizes. SS Butterfly Bulletin B51 Stainless steel body. Tri-Clamp end connections. Variety of seat materials. 1¹ ₂"-6" (38.1-152.4mm) sizes. Saunders Diaphragm Catalog SSV For sterile applications. ¹ ₄"-6" (6.4-152.4mm) sizes. Miscellaneous Valves Catalog MV Compressor, Plug, Relief, and Check Valves. 1"-4" (25.4-101.6mm) Tube OD. Tri-Blender Super-Speed Mainstream Streamline Pumps C Series Centrifugal Catalog CSP 5 sizes in capabilities to 1150 GPM (261m 3 /hr). 1¹ ₂"-6" (38.1-152.4mm) inlet. CL Series Centrifugal Catalog CLP 10 sizes in capacities to 1300 GPM (454 m 3 /hr). 2¹ ₂"-4" (63.5-101.6mm) inlet. CL WFI (Water For Injection/ Pharmaceuticals) Bulletin CLWFI 4 sizes in capacities to 700 GPM (159m 3 /hr). 1¹ ₂"-4" (38.1-101.6mm) inlet. EH Series Centrifugal (Low Shear) Bulletin EH 3 sizes in capacities to 1000 GPM (227 m 3 /hr). 3"-6" (76.2-152.4mm) inlet. PR Series Positive Rotary Catalog PR 6 sizes to 300 GPM. (68 m 3 /hr). 1"-6" (25.4-152.4mm) inlet and outlet. T Series Positive Rotary Bulletin TSR (TSR Standard Rotor Design) 12 sizes to 500 GPM/290 PSI. (113m 3 /hr/20 BAR) 1"-6" (25.4-152.4mm) inlet and outlet. TCIP Series Positive Rotary----Catalog TCIP 7 sizes to 500 GPM/215 psi. (113 m 3 hr/7 bar) 1-6 (25.4-152.3mm) inlet and outlet. Fittings Sanitary Fittings Catalog FTGS Tri-Clamp, Tri-Weld, and Bevel Seat for the food, beverage, and dairy industry 1"-4" (25.4-101.6mm) Bio-Pharm Fittings Catalog PHARM Tri-Clamp and Tri-Weld mechanical and electropolished fittings for the bioprocessing industry ½"-4" (12.7-101.6mm) Automated Systems Tri-Blender Bulletin TB Blends up to 350 lb./min. (159 kg) dry powder with up to 150 GPM. (34 m 3 /hr). CIP Systems Bulletin CIP Four standard models. Variations for hot sanitizing service. Filters/Strainers Bulletin BFS Built to sanitary standards. Low pressure drop and extended service. Bio-Pharm Systems Bulletin BP A range of products for Bio-Pharm applications. Tri-Clover Tri-Clover P.O. Box 1413 Kenosha, Wisconsin 53141-1413 PHONE: 262-694-5511 FAX: 262-694-7104 E-Mail address: TCWEBMASTER@tri-clover.com Visit our web site at www.tri-clover.com 2000 Catalog FV 2.5M 08/00