FLENDER ARPEX plate packs with conical bolting ARP Size 325-6 Assembly instructions FLENDER couplings
FLENDER ARPEX plate packs with conical bolting ARP Size 325-6 Assembly instructions Translation of the original assembly instructions Safety instructions Condition on delivery Fitting Alignment Start-up and operation Faults, causes and remedy Maintenance and repair 1 2 3 4 5 6 7 2 / 14
Notes and symbols in these assembly instructions Note: The term "assembly instructions" will in the following also be shortened to "instructions" or "manual". The term "2014/34/EU" used in these instructions applies to the version designed in conformity to directive 94/9/EC, if the product is put on the market by 19.04.2016, and to the version designed in conformity to directive 2014/34/EU, if the product is put on the market on or after 20.04.2016. Legal notes Warning-note concept This manual comprises notes which must be observed for your personal safety and for preventing material damage. Notes for your personal safety are marked with a warning triangle or an "Ex" symbol (when applying Directive 2014/34/EU), those only for preventing material damage with a "STOP" sign. WARNING! Imminent explosion! The notes indicated by this symbol are given to prevent explosion damage. Disregarding these notes may result in serious injury or death. WARNING! Imminent personal injury! The notes indicated by this symbol are given to prevent personal injury. Disregarding these notes may result in serious injury or death. WARNING! Imminent damage to the product! The notes indicated by this symbol are given to prevent damage to the product. Disregarding these notes may result in material damage. NOTE! The notes indicated by this symbol must be treated as general operating information. Disregarding these notes may result in undesirable results or conditions. WARNING! Hot surfaces! The notes indicated by this symbol are made to prevent risk of burns due to hot surfaces and must always be observed. Disregarding these notes may result in light or serious injury. Where there is more than one hazard, the warning note for whichever hazard is the most serious is always used. If in a warning note a warning triangle is used to warn of possible personal injury, a warning of material damage may be added to the same warning note. Qualified personnel The product or system to which these instructions relate may be handled only by persons qualified for the work concerned and in accordance with the instructions relating to the work concerned, particularly the safety and warning notes contained in those instructions. Qualified personnel must be specially trained and have the experience necessary to recognise risks associated with these products or systems and to avoid possible hazards. 3 / 14
Intended use of Siemens products Observe also the following: Trademarks Siemens products must be used only for the applications provided for in the catalogue and the relevant technical documentation. If products and components of other makes are used, they must be recommended or approved by Siemens. The faultfree, safe operation of the products calls for proper transport, proper storage, erection, assembly, installation, start up, operation and maintenance. The permissible ambient conditions must be adhered to. Notes in the relevant documentations must be observed. All designations indicated with the registered industrial property mark are registered trademarks of Siemens AG. Other designations used in these instructions may be trademarks the use of which by third parties for their own purposes may infringe holders rights. Exclusion of liability We have checked the content of the instructions for compliance with the hard and software described. Nevertheless, variances may occur, and so we can offer no warranty for complete agreement. The information given in these instructions is regularly checked, and any necessary corrections are included in subsequent editions. Note on the EC Machinery Directive 2006/42/EC Siemens couplings in the "FLENDER couplings" product range must be treated as "components" in the sense of the EC Machinery Directive 2006/42/EC. Therefore, Siemens needs not issue a declaration of incorporation. Information on safe fitting, safe startup and safe operation can be found in this instructions manual; in addition the "warning note concept" therein must be observed. 4 / 14
Contents 1. Safety instructions... 6 1.1 General notes... 6 1.2 Obligations of the user... 6 1.3 Protective equipment... 6 2. Condition on delivery... 6 2.1 Protective coating... 6 2.2 Marking the coupling parts in accordance with Directive 2014/34/EU... 7 3. Fitting... 7 3.1 General information on fitting... 7 3.2 Fitting the conical bolting... 7 3.3 Axial backlash limitation or vertical support (integrated)... 10 4. Alignment... 10 5. Start up and operation... 11 6. Faults, causes and remedy... 11 7. Maintenance and repair... 12 7.1 Demounting the plate pack with conical bolting... 12 7.2 Fitting and demounting aids... 13 5 / 14
1. Safety instructions 1.1 General notes These assembly instructions apply only to the series and sizes indicated on the cover sheet and always in conjunction with the superordinate operating instructions BA 8704 for the ARP series. 1.2 Obligations of the user All instructions and information in these assembly instructions and in the superordinate operating instructions BA 8704 for the ARP series must be observed and adhered to. Failure to observe these instructions may result in breakage of the coupling. Danger to life from flying fragments. A damaged coupling becomes an explosion hazard. Operating the coupling with damaged coupling parts is not permitted in potentially explosive environments in accordance with Directive 2014/34/EU. The operator must ensure that everyone carrying out work on the coupling has read and understood these instructions and is adhering to them in every point in order to: avoid injury or damage, ensure the safety and reliability of the coupling, avoid disruptions and environmental damage through incorrect use. During transport, assembly, installation, demounting, operation and maintenance of the unit, the relevant safety and environmental regulations must be complied with at all times. The coupling may only be maintained and/or repaired by persons qualified for the work concerned (see "Qualified personnel" on page 3 of this manual). The outside of the coupling must not be cleaned with high pressure cleaning equipment. All work must be carried out with great care and with due regard to safety. 1.3 Protective equipment All work on the coupling must be carried out only when it is at a standstill. The drive unit must be secured against being switched on accidentally (e.g. by locking the key switch or removing the fuses from the power supply). A notice should be attached to the ON switch stating clearly that work is in progress. The drive unit must be shut down as soon as inexplicable changes to the coupling are detected during operation. Rotating and/or movable drive components must be fitted with suitable safeguards to prevent contact. The operation of the coupling must not be impaired by the safeguard. Removed safety equipment must be re fitted prior to starting up. 2. Condition on delivery 2.1 Protective coating The ARPEX coupling parts delivered with these instructions are coated with a corrosion preventive agent (such as Tectyl). 6 / 14
2.2 Marking the coupling parts in accordance with Directive 2014/34/EU Couplings of the ARP series which are intended for use in potentially explosive environments in accordance with Directive 2014/34/EU must be marked accordingly. The precise marking and information on the application conditions of these couplings are given in the operating instructions BA 8704. They also contain the manufacturer s EC declaration of conformity. 3. Fitting 3.1 General information on fitting For information on cleaning the coupling parts and shaft ends as well as fitting the hub parts and the adaptor, see operating instructions BA 8704. 3.2 Fitting the conical bolting The conical bolting is delivered ready for fitting and comprises the following components (see figure 1): Taper sleeve, inside lightly greased Taper pin, outside lightly greased Interception ring Washer Tensioning bolt Screw plug 1 2 3 4 5 6 7 8 9 10 Fig. 1: Detailed view of the conical bolting 1 ARPEX flange 2 Ring 3 Bush 4 Screw plug 5 Taper pin 6 Taper sleeve 7 Plate pack / slide-bar plates 8 Interception ring 9 Washer 10 Tensioning bolt 7 / 14
Before fitting starts, the fitting holes and the contact surfaces for the conical bolting and plate pack on the ARPEX flange must be carefully cleaned of any dirt and rust preventive agent (such as Tectyl, paint). Observe manufacturer s instructions for handling solvent. Bolt the plate pack alternatingly in such a way to the coupling parts that the rings are in contact with the ARPEX flange and the washers on the interception rings (see figure 1). Then insert the taper sleeves from the outisde into their respective fitting holes on the ARPEX flange, as shown in figure 2, and, if necessary using a threaded rod and 2 washers (included in the delivery see figure 2), pull them through the ARPEX flange, the plate pack and the interception ring, until the collar of the taper sleeve is in full contact with the ARPEX flange (see figure 1). For fitting plate packs with integrated axial backlash limitation or vertical support, see item 3.3. 1 Fig. 2: Detailed view of the threaded rod 1 Threaded rod with 2 hexagon nuts (see figure 10 and table 4) Insert the lightly greased taper pin (re grease with lubricant indicated in table 2, if required) into the taper sleeve, as shown in figure 3, and fit washer and tensioning bolt, as shown. Tighten the tensioning bolts one after the other with approx. 0.5 x T A in the first pass (see table 1), if necessary, brace at the screw plug. Tensioning bolt and screw plug must be fitted with "medium firm" thread locking medium (e.g. Loctite 243). Then, in the second pass, tighten to T A (see table 1). After tightening, the end faces of the taper sleeve and taper pin must sit flush (see figure 1). 1 3 2 Fig. 3: Detailed view of the taper pin 1 Screw plug 2 Taper surface, greased 3 Tensioning bolt 8 / 14
Table 1: Fitting values for plate pack bolting Coupling Tensioning bolt Screw plug Thread Tightening torque Thread x x Size length length Tightening torque 0.5 x T A T A T A [mm] [Nm] [Nm] [mm] [Nm] 325 6 M 10 x 30 30 60 M 10 x 16 41 The specified tightening torques (table 1) must always be adhered to. Any other tightening torques may result in accelerated wear and damage to the coupling. Failure to observe these instructions may result in breakage of the coupling. Danger to life from flying fragments. A damaged coupling becomes an explosion hazard. Operating the coupling with damaged coupling parts is not permitted in potentially explosive environments in accordance with Directive 2014/34/EU. Table 2: Lubricants Lubricant paste OPTIMOL OPTIMOLY PASTE PL LP 430 AEMA SOL M019 P/PS Klüberpaste ALTEMP QNB 50 Klüberpaste 46 MR 401 MOLYKOTE G-RAPID PLUS PASTE Manufacturer Castrol Industrie GmbH D 41179 Mönchengladbach Microgleit GmbH D 74357 Bönnigheim Matthes GmbH D 42653 Solingen Klüber Lubrication KG D 81379 München Klüber Lubrication KG D 81379 München Dow Corning Europe S.A. B 7180 Seneffe Observe the manufacturer's instructions for handling lubricants. Fitting and start up must be done by qualified personnel only 9 / 14
3.3 Axial backlash limitation or vertical support (integrated) When fitting the plate packs with integrated axial backlash limitation or vertical support, the same procedure applies as described in item 3.2. However, the following must be noted additionally: The plate pack must be bolted to the coupling parts so that the respective tie of the star plate of the integrated axial backlash limitation or vertical support is in contact with the ARPEX flange at the point of bolt connection (see figure 4). Only in this fitting position is correct operation of the axial backlash limitation or vertical support guaranteed. If wrongly fitted (tie of the star flange is not fitted as shown in figure 4), the integrated axial backlash limitation or vertical support will not be able to operate properly and will cause coupling damage during operation. 1 2 3 4 9 10 7 6 5 8 11 Fig. 4: Fitting the plate packs with integrated axial backlash limitation or vertical support 1 ARPEX flange 2 Interception ring 3 Washer 4 Star flange 5 Star flange 6 Washer 7 Interception ring 8 ARPEX flange 9 Tie of star flange 10 ARPEX flange 11 Star flange Failure to observe these instructions may result in breakage of the coupling. Danger to life from flying fragments. A damaged coupling becomes an explosion hazard. Operating the coupling with damaged coupling parts is not permitted in potentially explosive environments in accordance with Directive 2014/34/EU. 4. Alignment ARPEX couplings compensate for alignment faults in the shafts to be connected. Couplings with two plate packs support axial, radial and angular misalignment. Couplings with one plate pack support only angular and axial misalignment. 10 / 14
When aligning machine parts with a sliding caliper gauge, measure the distance "S 1 " (see figure 5 and table 3) between the coupling flanges at a number of measuring points. If the measured flange distances are within the range of values shown between S 1 min. and S 1 max. (table 3), the machine parts are sufficiently precisely aligned. S 1 max. S 1 min. M M M M M M S 1 min. S 1 max. Fig. 5: Aligning the machine parts S 1 = Distance between coupling flanges S 1 min. = see table 3 S 1 max. = see table 3 M = Measuring point The fitting misalignment must not exceed nor fall below the values for S 1 min. and S 1 max. (table 3). It is however recommended to align the coupling as precisely as possible so as to have an additional margin for misalignment in operation. Impermissible fitting misalignments may cause accelerated wear and damage to the coupling. Failure to observe these instructions may result in breakage of the coupling. Danger to life from flying fragments. A damaged coupling becomes an explosion hazard. Operating the coupling with damaged coupling parts is not permitted in potentially explosive environments in accordance with Directive 2014/34/EU. Table 3: Permissible fitting misalignment ARPEX S 1 S 1 S 1 min. max. Size [mm] [mm] [mm] 325 6 22.0 21.3 22.7 5. Start up and operation Instructions and information relating to start up and operation can be found in operating instructions BA 8704 (ARP series). 6. Faults, causes and remedy Detailed information and instructions relating to faults and their causes and remedy can be found in operating instructions BA 8704 (ARP series). 11 / 14
7. Maintenance and repair Instructions and information relating to maintenance and repair can be found in operating instructions BA 8704 (ARP series). 7.1 Demounting the plate pack with conical bolting Unscrew all screw plugs. Unscrew all tensioning bolts and remove washers. Using the washer and tensioning bolt, pull the taper pin out of the taper sleeve. Prevent the taper pin from turning by screwing in another tensioning bolt and the demounting disk (see figure 6). Pull the taper sleeve out of the ARPEX flange and the plate pack. Use for this the aids shown in figures 8 to figure 10 (pulling off tool, demounting disk, threaded rod and nuts) as well as the washer (see figure 7). 1 3 4 5 2 Fig. 6: Detailed view of the tensioning bolt 1 Tensioning bolt 2 Washer 3 Interception ring 4 Demounting disk 5 Tensioning bolt 1 4 5 6 2 3 Fig. 7: Detailed view of the threaded rod 1 Nut 2 Washer 3 Pulling-off tool 4 Demounting disk 5 Threaded rod 6 Nut 12 / 14
7.2 Fitting and demounting aids The following aids are required (for dimensions, see table 4): 1 x Threaded rod (figure 10) 2 x Nut DIN EN 24032 (figure 10) 1 x Pulling off tool (figure 8) 1 x Demounting disk (figure 9) B d1 L H 6 Fig. 8: Pulling off tool (6 mm U section) L1 d2 d1 D1 L2 Fig. 9: Demounting disk L3 M Fig. 10: Threaded rod and nuts Table 4: Coupling Size Dimensions of fitting and demounting tools Pulling-off tool (6 mm U-section) Demounting disk Threaded rod B H L Ø d 1 Ø D 1 Ø d 1 Ø d 2 L 1 L 2 L 3 M [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Nut 325 6 50 35 35 11 22 11 16 13 8 115 10 13 / 14
Further Information: "FLENDER gear units" on the Internet www.siemens.com/gearunits "FLENDER couplings" on the Internet www.siemens.com/couplings Service & Support: http://support.automation.siemens.com/ww/view/en/10803928/133300 Lubricants: http://support.automation.siemens.com/ww/view/en/42961591/133000 Siemens AG Industry Sector Mechanical Drives Alfred-Flender-Straße 77 46395 Bocholt GERMANY Subject to modifications Siemens AG 2012 www.siemens.com/drive technologies