Slide Gate Maintenance Manual Terminal City Iron Wks Ltd. Unit#3 99 19th Street, Langley, BC V1M 3C
This Maintenance Manual is intended to give a guide to Maintenance. The Manual covers: Maintenance and Service procedures Parts list f T.C. Slide Gate Fire s Trouble shooting to find the problem. The Manual does not deal with specific problems but rather assists you in explaining the problem to those in maintenance who are required to keep the hydrants fire-fighting fit. Me specific detailed infmation is available upon request. INSPECTION It is recommended that fire hydrants be inspected twice a year. The generally accepted times are during Spring and Fall. It is also strongly recommended that hydrants be serviced immediately after they have been used by the fire department at a fire, after extensive flow such as flushing mains, etc. SERVICE CALL The spring inspection is a service call, and will check out the hydrant after the results of winter frost, ground heave, snow, road salt and sand, etc. have left their mark. The general procedure is to fully open the hydrant and the outlet caps left on in der to pressurize the hydrant. The operating characteristics which will be covered in this simple operation are: insufficient number of turns to open (should have 7 to 9 f Side Gate) hard-binding operation in opening and closing. leakage through stuffing box seals. leakage at outlets and outlet caps. leakage at ground-line flange gasket. leakage through CLOSED drain pt. continuous turning of the operating spindle with no opening of the hydrant taking place. After checking f the above on this inspection the hydrant should be fully closed and one of the 1 /-inch outlet caps removed. The operating characteristics which will be covered in this simple operation are: non-drainage of hydrant (feel f suction when hand placed over open pt f crect drainage). leakage past valve seat (continuous running of water). plugged drain preventing drainage. If any of the above characteristics are present then the spring service call will become a MAINTENANCE call. None of the above listed characteristics should be present in the hydrant, and if they are, then they should be crected. MAINTENANCE & SERVICE CALL: The fall inspection is a maintenance call and will require the removal of internal operation parts f visual inspection. The general procedure is to shut off the isolating gate valve on the line into the hydrant and after opening the hydrant to the full open position the operating mechanism, valve and internal parts are removed from the hydrant f inspection, lubrication and replacement of wn damaged parts. A careful inspection should be made of: the straighteness of the operating spindle and off-pitch twist of the thread on the main gate screw. the main Gate rubber, drip valve rubber, After replacement of damaged and wn parts and after complete lubrication of all moving parts the hydrant is re-assembled. The hydrant now MUST BE SERVICED as was done in the spring call, that is, open the hydrant full and pressurize the hydrant with water and follow with a check of all the spring call characteristics. The servicing AFTER maintenance assures that two very imptant points have been covered. I. The isolating gate valve has been turned back on in der to pressurize fill the hydrant with water.. A check is made of the crectness of the wk done on maintenance. All gaskets are tight, the crect number of turns, ease of operation, crect drainage, etc. The hydrant has been left in wking der.
FIRE HYDRANTS - Slide Gate No. 1 No. No. P When dering Terminal City Slide Gate Fire s. please give infmation listed below: Type of : No. 1: - 1 / - inch outlets and a pumper outlet. No. 1-1: - 1 / - inch outlets and a pumper outlet. No. : - 1 / - inch outlets. No. P: - 1 / - inch outlets and a pumper outlet. Depth of Bury: The distance from the ground line to the centre line of the inlet connection in inches. Available in increments of -inch. Direction of Operation: The hydrants are nmally supplied to open by rotating the spindle in a counter-clockwise direction. Operating Spindle Nut: Shape and size. Pentagon - 1 1 / - inch from point to flat. Square - 1 1 / - inch from point to flat. Three sided - 1 7 /1 -inch arc from point to flat. Thread Specifications: The 1 / - inch outside diameter. Outlets - Pitch of thread. The pumper - Outside diameter in mm. Outlet - Pitch of thread. Inlet Connections: Size - -inch Style - Mechanical Joint, Push - On, Flanged Terminal City Slide Gate Fire s are readily serviceable with proper design to give unrestricted maximum flow. Terminal City Slide Gate Fire s have all wking parts accessible f inspection and servicing. Terminal City Slide Gate Fire s are assembled with all parts manufactured to give interchangeability. Terminal City Slide Gate Fire s are provided with automatic self-draining thus leaving the hydrant completely dry f cold weather conditions. Where nmal hydrant drainage is impossible special arrangements can be provided. Terminal City Slide Gate Fire s are designed to prevent contact of the seating surfaces during opening and closing thereby eliminating wear of the seating surfaces. Terminal City Slide Gate Fire s are provided with 1 /-inch outlets and operating pentagon manufactured to the British Columbia Fire Hose Thread Specifications (unless otherwise specified). Terminal City Slide Gate Fire s are made in the following styles: No.1 : Constructed with - 1 / -inch outlets and a pumper outlet. The inside diameter of the barrel is 3 / inch. No. : Constructed with - 1 / -inch outlets. The inside diameter of the barrel is 5 3 / -inch. No. P : Similar to the No. with the addition of a pumper outlet. Material Specifications: AlI cast iron parts are manufactured to ASTMA A--B. AlI bronze parts are manufactured to ASTM B-. Stainless steel f main spindle type 1. Mild steel to SAE 1. When dering parts f the No. 1 No., prefix the part numbers with No. 1 No.. e.g. if dering a main gate casting specify part No. - No. 1 -. 1
NO. NAME MATERIAL NO. NAME Material 3-1 Barrel Cast Iron 31 Operating Stem Gland O Ring Syn. Rubber IX No. I Extension Cast Iron 5 Nut Mild Steel Bottom End Cast Iron 53 Pumper Hose Outlet Cap Gasket Rubber Red Main Gate Cast Iron 55 Square Stem to Collar Pin Mild Sleel Stem Collar Cast Iron Ind. & Plain Hose Outlet Cap Gasket Rubber Red 9 Ind. & Plain Hose Outlet Cap Cast Iron 7 Nut, Extension Bolt Mild Steel 3-1 Plain Hose Outlet Bronze Extn. to Barrel & Bottom End Gasket Rubber CBS 11 Main Gate Screw St ls St l 9 Sq. Stem to Main Gate Screw Pin Mild Steel 11A Square Stem to Screw Coupling Ductile Iron 7 Bolt, Ind. Cut-off Gate Chain Brass Main Gate Wedge Nut Bronze 71 Chain, Ind. Cut-off Gate Galv. Steel 13 Main Gate Seat Ring Bronze 17 Bonnet Bolt Brass 1 Main Gate Seat Plate Bronze 3 Operating Stem Mang Bronze 15 Main Gate Seat Nut Bronze Cast Iron 1 Screwed End Piece Bronze 9 Bonnet Cast lron 17 Drip Cup Bronze 3 Independent Cut-off Screw Yellow Brass 1 Drip Valve Washer Bronze Square Stem Mild Steel 19 Drip Valve Bolt Bronze Gasket Drip Valve Nut Bronze Main Gate (#) Cast lron 1 Drain Action Spring St ls St l 1 Main Gate Wedge Nut (#) Bronze 3 Gate Valve Rubber Rubber Bottom End (#) Cast Iron Drip Valve Rubber Rubber 3 Main Gate Seat Ring (#) Bronze 5 Pumper Hose Outlet Bronze Main Gate Seat Plate (#) Bronze Pumper Hose Outlet Cap Cast Iron Gasket (#) Rubber 3-7 Independent Hose Outlet Bronze 7 Extn. to Barrel & Bottom End Gasket (#) Rubber Independent Cut-off Gate Bronze Barrel to Extn. Stud (#) St ls St l 31 Independent Cut-off Nut Bronze 59 Plain Hose Outlet Cap (#) Cast Iron 3-33 Independent Cut-off Screw Gland Bronze IOIX No. Hyd t Extn. (#) Cast Iron 37 Barrel to Bolt St l ASTMA -31 - Square Stem (#) Mild Sleel 3 Extension Bolt Mild Steel 1 Operating Stem (#) Mang. Bronze 3- Ind. Cut-off Screw Gland O Ring Syn. Rubber 17 Bolt Hex Bronze 3-1 Ind. & Plain Hose Outlet O Ring Syn. Rubber 1 Bonnet Cast Iron 3- Ind. & Plain Hose Outlet Locking Ring Bronze Cast Iron When dering parts f No. 1 No. s prefix part numbers with No. 1 No. SERVICE and MAINTENANCE EVERY MONTHS:- Flush out by removing plain nozzle cap (not shown) and opening main gate at least turns. Upon closing hydrant after flushing place hand over nozzle opening to check that vacuum is being created. This shows that hydrant is draining properly. EVERY YEAR:- a. Lubricate - see table. b. Inspect Packing - replace if it has gone hard. c. Inspect Rubber Surfaces on Main Gate and Drip Valve f tears & pitting caused by Silt, Rocks Etc. - replace if damaged. d. Inspect all other internal components such as Drip Valve, Wedge Nuts. Main Gate Etc. No. Name of Part 11 Main Gate Screw 9, 1, 5,, 7 Main Gate Wedge Nut Threads of 1 / & Pumper Outlet & Caps 7 Top Spindle Top Spindle Packing Lubrication Recommended Grease Environmentally Friendly Food Grade Grease Remarks Give ample coating Give ample coating Give ample coating where spindle passes through stuffing box & where shoulder of spindle bears against head. Seal off top of packing with grease to prevent freezing.
Fire Slide Gate Parts Chart 3
Maximum Flow Self Draining Slide Gate s Two suggested methods of installing hydrants to the main Independant Cut Off Valve 1 / O Ring Outlet Assembly Pat. #77 Main Gate Assembly O Ring Packing Gland The purpose of the following suggested methods of installation is to allow flexibility so that a minimum of direct vehicular impact to the hydrant would be transferred to the main. Method A: This method requires a hub end tee from the main connected by a nipple of pipe to a hub end valve. The valve, in turn is connected by another nipple of pipe to the hub end inlet connection of the hydrant. The hub ends on the branch of the tee, valve and hydrant are provided with tie lugs to carry the tie rods as shown. Method B: This method requires a hub x hub run x flange branch from the main with a flange x hub valve bolted to the flange outlet of the tee. A nipple of pipe is used to connect the hub of the valve to the hub inlet connection of the hydrant. The hubs of the valve and hydrant are provided with tie lugs to carry the tie rods as shown. DIRECTIONS FOR REMOVING INTERNAL PARTS From a study of the hydrant drawing shown on page 7 the following details may be easily followed. Shut off the water supply to the hydrant and open the hydrant no less than eight turns. Take off the bonnet by removing the two bonnet nuts. Take off the head assembly by removing the two head nuts. The entire gate assembly may now be lifted out by means of the operating rod. When the gate reaches the top of the hydrant, turn to bring it out through the widest diameter, being careful not to injure the face of the gate rubber. DIRECTIONS FOR RE-ASSEMBLING INTERNAL PARTS Care must be taken to insure the proper location of the gate and drain mechanism f re-assembly. Have gate assembly approximately half way up the main gate screw. Drop the gate assembly through the widest diameter of the top of the body, then turn so that the face of the gate faces the inlet of the hydrant. Lower carefully by the square stem until the drip valve is properly located in the drip cup. Re-assemble the head assembly and bonnet. Open and close the hydrant two three times to assure crect alignment and proper functioning of all parts befe turning on the water. DIRECTIONS FOR EXTENDING HYDRANTS Follow directions f removing internal parts. Remove the top body section. Place required length of extension. Extensions are available in multiples of -inch. Replace the top body section after being sure the flange faces and gaskets are clean. Add the square steel rod supplied with the extension assembly to the TOP of the existing square rod f -inch and longer extensions. F a -inch extension the square rod supplied with the extension assembly MUST BE FITTED and PINNED into the main gate spindle coupling 11A and tightened by set screw onto the existing square rod. Extension assemblies are in -inch increments f extending hydrants. They are supplied complete with rod, coupling and one set of body bolts and gasket.
TROUBLE SHOOTING FROM OPERATING CHARACTERISTICS 1. Fire fails to open upon rotation of the operating spindle: Slide Gate : stripped thread on main spindle main gate nut (11; ). broken spindle coupling (11 A). broken main spindle (11). top operating spindle not engaged with operating rod (3 & 1 & ).. Fire will not open operating spindle will not turn: Slide Gate : hard, wn, overtightened packing in the hydrant head packing gland binding on the top spindle (3 & 1). bent main gate spindle and/ off-pitch thread on the main spindle and main gate nut causing a seized unit (11,). 3. Fire will not shut off: Slide Gate : feign material trapped on the seating surfaces (3;13). damaged and wn rubber seat (3) damaged seat ring (13) feign material trapped in the bottom end not allowing the main gate to travel down to the internal stop position (;). External leakage from HEAD, Outlet Caps, Groundline Flange Stuffing Box: damaged gaskets. wn damaged rings. hard dry wn flax packing. 7. Fire is hard operating: lack of lubrication. bent main spindles. off-pitch threads. stuffing box flax packing too hard and wn. stuffing box rings jammed with silt from external internal source. stuffing box and/ gland pulled down on an angle thus binding the operating spindle.. Vibrating Chattering Fire : wn rubber seat. soft rubber seat. use of too many sht extension assemblies. loose rubber seat.. Non-Draining of the after shutoff: the outlet caps replaced onto the outlets immediately after closing of the hydrant. Allow at least 15 minutes befe replacing caps. feign material plugging the drain hole an elbow boot completely encased in concrete. the hydrant could have been manufactured as a "nondrain style". The non-draining feature is available f areas of high ground water table and the hydrant must be pumped out after use. in the case of the SLIDE GATE HYDRANT also watch f the drain assembly broken off the end of the main spindle and laying in the drip cup in the boot (, 11 & drip assembly). 5. Leakage around hydrant barrel at the surface of the ground: drain mechanism is not closed. offset line from the main is cracked at the socket entrance to the hydrant a leaking joint in the hydrant socket. feign material trapped in the drain.. feign material trapped on seating surface preventing final to 3 turns of the main valve closure. wn drip valve rubber 5
SELF-DRAINING STANDPIPE The Terminal City two-inch self-draining stand pipe is a facty assembled unit specifically designed and constructed to take the place of in-field component assembled units. The self-draining stand pipe can be supplied with 1/" B.C. Std hose outlet. MATERIALS The unit is manufactured with bronze operating and draining components. The valve seating surface, main body, operating thread and spindle are manufactured with A.S.T.M. B- bronze. The stuffing box and draining mechanism have ring rubber gaskets f sealing purposes. Polyurethane anti-sce seating material is used f the valve disc facing. ACCESSIBILITY All moving parts subject to wear are readily accessible from above ground by the removal of the top body casting. DRAIning Mechanism When the stand pipe is not in use the drain pts remain open, thereby providing a dry barrel f frost conditions. During the first turn of the operating rod water is expelled through the drain pts as well as rising in the barrel of the stand pipe. This allows the drain pts to be flushed and removes any feign material which may become lodged in the mechanism. During the remaining opening turns the drain mechanism is closed. After closing it is recommended that the stand pipe be allowed to drain befe replacing the pt cap on the outlet. PARTS LIST Part No. NAME Material 1 Handwheel Aluminum Handwheel Bolt Brass 3 Washer Brass Handwheel Stem Cast Bronze 5 Top End Ring Houghton 11 Handwheel Stem Pin St l s Steel 7 Top End Cast Iron Pipe Steel 9 Operating Rod Steel 1 Gate Pin Stainless Steel 11 Drain Shield Plastic Screwed Gate Ring Houghton 7 13 Bottom End Cast Bronze 1 Screwed Gate Cast Bronze 15 Cotter Pin Brass 1 Valve Discwasher Steel 17 Valve Disc Urethane MATERIAL SPECIFICATIONS Cast Iron (C.I.) to ASTM A--B Mild Steel (M. St.) to SAE 1 Bronze (Br z) to ASTM B- Urethane, Durometer
Bury Pipe Rod.15m ' - " ' - " ' - 3/".3m 1' - " ' - " ' - 1 3/-.5m 1' - " 3' - " 3' - 3/".m ' - " 3' - 3' - 1 3/".75m ' - " ' - " ' - 3/".9m 3' - " ' - " ' - 1 3/" 1.5m 3' - " 5' - " 5' - 3/" 1.m ' - " 5' - " 5' - 1 3/" 1.35m ' - " ' - " ' - 3/" 1.5m 5' - " ' - " ' -1 3/" 1.5m 5' - " 7' - " 7' - 3/" 1.m ' - " 7' - " 7' - 1 3/" 1.95m ' - " ' - " ' - 3/".1m 7' - " ' - " ' - 1 3/".5m 7' - " 9' - " 9' - 3/".m ' - " 9' - " 9' - 1 3/".55m ' - " 1' - " 1' - 3/".7m 9' - " 1' - " 1' - 1 3/".5m 9' - " 11' - " 11' - 3/" 3.m 1' - " 11' - " 11' - 1 3/" 3.15m 1' - " ' - " ' - 3/" 3.3m 11' - " ' - " ' - 1 3/" 3.5m 11' - " 13' - " 13' - 3/" 3.m ' - " 13' - " 13' - 1 3/" 3.75m ' - " 1' - " 1' - 3/" 3.9m 13' - " 1' - " 1' - 1 3/" PARTS LIST Part No. NAME Material 1 Handwheel D.I. Handwheel Bolt Brass 3 Washer Brass Handwheel Stem Cast Bronze 5 Top End Ring Houghton 11 Handwheel Stem Pin Stainless Steel 7 Top End Cast D I Pipe Steel 9 Operating Rod Steel 1 Gate Pin Stainless Steel 11 Drain Shield PVC Screwed Gate Ring Houghton 7 13 Bottom End Cast Bronze 1 Screwed Gate Cast Bronze 15 Cotter Pin Brass 1 Disc Washer Stainless Steel 17 Valve Disc Urethane 1 Coupling D.I. Top Coupling (Primer) Bottom Coupling (Galv.) S.S Nuts & Bolts MATERIAL SPECIFICATIONS Cast Iron (C.I.) to ASTM A--B Mild Steel (M. St.) to SAE 1 Ductile Iron (D.I.) to ASTM A53 (5-5-) Bronze (Br z) to ASTM B- Urethane, Durometer D 7
ENGINEERING DATA (IMPERIAL) PRESSURE IN LBS. PER SQUARE INCH AND EQUIVALENT HEAD OF WATER IN FEET, ALSO HEAD OF WATER IN FEET AND EQUIVALENT PRESSURE IN I.B. PER SQUARE INCH LB Equivalent PSI LB Equivalent PSI LB Equivalent PSI 1.31.35 15.77 5.1 5 73.9. 5 11.5.1 11 5.33 7.57 1 5.5 9. 1 3..3 115 5.9 9.73 15 95.1 9.9 15 3.. 77.5 51.9 5. 95.15..5 5 9.1 5. 5 5. 97.31 5 57. 1.1 13 3.57 5. 3 531.7 99.7 3 9.3.97 135 3.13 5.3 35 53.3 11.3 35.9 15.13 1 33.9,55 55.9 13. 9. 17.31 15 335.5.71 5 5. 15.9 5 1. 19. 15 3.1.7 5 57. 1. 5 115. 1. 155 35.37 7.3 55 59.5 11. 55 7.1 3.7 1 39.93 9. 1.1 1.5 13.7 5.95 15 31.9 71.3 5.7 11.1 5 15..11 17 393.5 73.5 7. 11.77 7 11. 3.7 175.1 75. 75 35. 11.93 75 173. 3.3 1 1.17 77.5 7.3 1.1 1.9 3. 15 7.73.1 5 5.9 3. 5 19.5 3.7 19 39.9.17 9 7.5 5. 9. 3.9 195 5.5.33 95. 7.5 95 19. 1...5 3 93.3 9.75 1 31.5 3.5 FIRE HYDRANT HEAD LOSSES TC-C71P = Compression - 1 / - inch and 1 - pumper outlet. TC-1 = No. 1 Slide Gate - 1 / - inch and 1 - pumper outlet. TC- = No. Slide Gate - 1 / - inch outlet. TC-1G = No. 1 Slide Gate - 1 / - inch and 1 - pumper outlet (1-1 / c/w independent cut-off valve). HYDRANT DISCHARGE IMPERIAL GALLONS PER MINUTE 3 5 FIG. 1 FIRE HYDRANT TEST HEAD LOSS COMPLETE HYDRANT VARIOUS HYDRANTS - 1/ - INCH OUTLET FLOWING 1 1 15 3 5 7 HEAD LOSS POUNDS PER SQUARE INCH TC C71P TC 1 TC TC 1G IMPERIAL GALLONS PER MINUTE 3 5 FIG. 1 FIRE HYDRANT TEST Capaciy vs. Drop Main Line to Hose Various s - 1/ - INCH OUTLET FLOWING TC C71P TC 1 TC TC 1G When flow TC-C71P TC = 1 1 15 3 5 7 9 1 PRESSURE DROP ACROSS HYDRANT POUNDS PER SQUARE INCH Note: drop change in pressure head from water main at hydrant base to hose. When flowing 15 Imp. gal./min. Loss through the hydrant TC-C71P = 13 p.s.i. TC-1 = 17 1 / TC = 1 1 / p.s.i. TC-1G = 1 p.s.i.
ENGINEERING DATA (Metric) PRESSURE IN AND EQUIVALENT HEAD OF WATER IN METRES, ALSO HEAD OF WATER IN METRES AND EQUIVALENT PRESSURE IN Equivalent Equivalent Equivalent Metres HEAD METRES Metres HEAD METRES Metres HEAD METRES.5.51.9. 15.. 3. 1.1 9.791 3.3 5.193 5.59.595. 19.5. 3.9.9 5.3 3.3 9.373 5.55.755 7.79.177. 39.1.5 5.5.9 9.9 5.51.955 7.75.357 9.99 79.759. 5.7.5 7.1 5 5.1 9.55 7.71.537 9.95 3.939. 57..1 7.3 3 3. 93.73 7 7.1 5.37 9.91.119 31 3.1 33.51.1 73. 1 1. 97.91 3 3. 313.3 9 9.1 1.19 11 1. 17.71 33 3.3 33.13 1 1. 979.1 1. 117.9 3 3. 33.9 11 11. 177.1 13 1.3 7.3 35 3.57 3.5. 117.9 1 1. 137.7 3 3.7 35.7 13 13. 7.3 15 1.53 1.5 37 3.77 3.7 1 1. 137.7 1 1.3 15.5 3 3.7 37.5 15 15.3 1.5 17 1.73 1.7 39 3.97 31.9 1 1.3 15.5 1 1.3 17.3. 391. 17 17.3 1.7 19 1.93 1.9 1.1 1.31 1 1.3 17.3. 195.. 11. 19 19.3 1.9 1.1 5.11 3.3 1.13. 195. FIRE HYDRANT CAPACITIES FIG.1 TC-C71P = Compression - 5mm and 1 pumper outlet. TC-1 = No. 1 Slide Gate - 5mm and 1 pumper outlet. TC- = No. Slide Gate - 5mm outlets. FIRE HYDRANT HEAD LOSSES FIG. When flowing litres/min. loss through the hydrant TC-C71P = 7.5 TC- = 9. TC-1 = 9. 1 1 FIG. 1 FIRE HYDRANT TESTS CAPACITY VS. PRESSURE DROP MAIN LINE TO HOSE TC C71P WITH -5 MM OUTLETS OPERATING Note: drop is change in pressure head from water main at hydrant base to hose. 5 1 3 5 7 9 C71P PRESSURE DROP KILOPASCALS Created Drop Across Flow 1 min.9 1.15.3 3 79.35 7.5 5 1.3 55.3 7 33.1 7. 9 517.5 1 1 1 FIG. FIRE HYDRANT TESTS HEAD LOSS COMPLETE HYDRANT TC C71P WITH -5 MM OUTLETS OPERATING 5 1 3 5 7 9 C71P HEAD LOSS KILOPASCALS Capacity 1 min Loss 1 3.5 9. 3.7 33. 5 51.75 7.5 7 1.5 131.1 9 17. 1 7. 1 1 5 1 3 5 7 9 TC1 PRESSURE DROP KILOPASCALS 1 FIG. 1 1 FIRE HYDRANT TESTS CAPACITY VS. PRESSURE DROP MAIN LINE TO HOSE FIG. 1 FIRE HYDRANT TESTS CAPACITY VS. PRESSURE DROP MAIN LINE TO HOSE TC 1 WITH -5 MM OUTLETS OPERATING Note: drop is change in pressure head from water main at hydrant base to hose. TC 1 WITH -5 MM OUTLETS OPERATING Note: drop is change in pressure head from water main at hydrant base to hose. 5 1 3 5 7 9 TC PRESSURE DROP KILOPASCALS Created Drop Across Created Drop Across Flow 1 l min.9 1. 51.75 3 93.15 11.5 5.1 7.3 7 351.9.9 9 555.5 1 Flow 1 l min.9 1.15.37 3 9. 15.97 5 7. 7.5 7 35.7.3 9 57.7 1 1 1 FIG. FIRE HYDRANT TESTS HEAD LOSS COMPLETE HYDRANT TC 1 WITH -5 MM OUTLETS OPERATING 5 1 3 5 7 9 TC1 HEAD LOSS KILOPASCALS 1 FIG. 1 FIRE HYDRANT TESTS HEAD LOSS COMPLETE HYDRANT TC WITH -5 MM OUTLETS OPERATING 5 1 3 5 7 9 TC HEAD LOSS KILOPASCALS Capacity 1 l min Loss 1 3.5 1.35 3.15 1. 5 5.55 9.7 7.75 15.7 9 3.55 1 51.5 Capacity 1 l min Loss 1.3 13. 3.7.5 5 7. 9.5 7 13.1 171. 9 1. 1 5.5