GENUINE PARTS INSTALLATION INSTRUCTIONS

1. DESCRIPTION: Portable Navigation 2. APPLICATION: Frontier (2005-2008) Xterra (2005-2008) All grades (2005-2007) Base or S-grade only (2008) 3. PART NUMBER: PND main kit (999Q5 KU000) PND Housing (999Q5 KU001) 4. KIT CONTENTS (PND Housing): Item QTY Description A 1 Housing Assembly B 1 Installation Instructions C 1 Wire Tap 5. TOOLS REQUIRED: Masking Tape Plastic pry bar Phillipps screwdriver (#2) Electrical tape 6. PRE-INSTALLATION CAUTIONS/NOTES Dealer Installation Recommended. Instructions refer to Service Manual. Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of mounting clips. - Remove upper cluster lid C tray. Install wire tap. 5. TOOLS REQUIRED: Masking Tape Plastic pry bar Phillipps screwdriver (#2) Electrical tape 6. PRE-INSTALLATION CAUTIONS/NOTES Dealer Installation Recommended. Instructions refer to Service Manual. Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of mounting clips. - Remove upper cluster lid C tray. Install wire tap. GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Nissan Portable Navigation 2. APPLICATION: Frontier (2009) except base grade Xterra (2009) except base grade 3. PART NUMBER: Portable Navigation Device (PND) main kit (999Q5 KU000) with factory BTHF or Optional PND main kit (999Q5 VV000) only w/o factory BTHF PND housing (999Q5 KV001) 4. KIT CONTENTS (PND Housing): Item QTY Description A 1 Housing Assembly B 1 Installation Instructions Replacement Template C 1 Wire Tap GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Portable Navigation 2. APPLICATION: Frontier (2005-2008) Xterra (2005-2008) All grades (2005-2007) Base or S-grade only (2008) 3. PART NUMBER: PND main kit (999Q5 KU000) PND Housing (999Q5 KU001) 4. KIT CONTENTS (PND Housing): Item QTY Description A 1 Housing Assembly B 1 Installation Instructions C 1 Wire Tap A B C 5. TOOLS REQUIRED: Masking tape Plastic pry bar Multimeter Phillips screwdriver (#2) Electrical tape 6. PRE-INSTALLATION CAUTIONS/NOTES Dealer Installation Recommended. Instructions refer to Service Manual. Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of mounting clips. - Remove upper cluster lid C tray. Install wire tap. Page 1 of 10 999Q5 KV100 II REV 1 12-10-09

1) Apply the parking brake. 2) Record the customer radio presets. Preset 1 2 3 4 5 6 7 A B C D 3) Make sure the shift lever is engaged in the P position and the parking brake is ON. 4) Turn the ignition switch OFF. 5) Open the engine hood. 6) Disconnect the battery negative terminal. Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of mounting clips. Fig. 1 7) Remove cluster lid C tray. Fig. 1 a) Apply masking tape. b) Create gap by pulling tray toward rear of vehicle or pull tray at rear corners. c) Insert plastic pry bar in gap. Fig. 2 8) Remove fastener. Fig. 2 Remove fastener Page 2 of 10 999Q5 KV100 II REV 1 12-10-09

Remove fasteners Fig. 3 9) Remove fasteners (2 places). Fig. 3 Fig. 4 10) Remove cluster bezel. Fig. 4 a) Remove cluster bezel by pulling toward rear of vehicle. b) Disconnect wiring. Page 3 of 10 999Q5 KV100 II REV 1 12-10-09

11) Identify the connector type by inspecting the back of the radio head unit, Type 1 or Type 2. Fig. 5 est connector with the largest wires from the radio head unit. Fig. 5 connect the largest connector with the largest wires from the radio head unit. Fig. 5 1 (green wire with black stripe - reference only). Fig. 5 pin 7 (green wire with black stripe - reference only). Connector view releasing tab facing up. Fig 5 See steps 12-17 for wire-tap installation instructions. Type 1 Type 2 Fig. 5 Type 1 Type 2 Pin 1 Pin 7 Pin 1 Pin 7 7 Radio side of connector Radio side of connector Page 4 of 10 999Q5 KV100 II REV 1 12-10-09

b) Fig. 6 12) Tap vehicle wire. Fig. 6 a) Remove cap (slot side) from tap body. b) Slide cap around vehicle wire. a) c) Note: Do not re-use the tap for subsequent reinstallation. Fig. 7 13) Inspect the tap to ensure correct installation. Fig. 7 Note: Avoid putting pressure on the vehicle wire and tap for the rest of the installation. i. Straight and evenly spaced all the way around. ii. Tight and minimize gap (wire jacket should be crushed). Fig. 8 14) Disconnect harness from housing assembly. Fig. 8 Page 5 of 10 999Q5 KV100 II REV 1 12-10-09

e) Insert wire to here a) d) f) Tighten Fig. 9 15) Tap red wire from housing harness. Fig. 9 a) Remove tap (non-pierce) side from tap. b) Remove protective stub from red wire. c) c) Insert red wire through the non-pierce side opening. d) Spread the individual strands into fan shape. e) Insert wire into the tap body and ensure that it is all the way in. i. Straight and evenly spaced all around ii. Tight and no gap iii. Test the signal Fig. 10 wire. Fig 10 a) Inspect the tap to ensure correct installation. b) Using a multimeter, check for 12 volts on the accessory wire. Note: Avoid putting pressure on the vehicle wire and tap for the rest of the installation. a) b) Fig. 11 17) Secure the tap. Fig. 11 a) Secure the body to harness, where vehicle wire is being tapped, with electrical tape b) Secure the tapped wire on the non-pierce side to the body of the posi-tap with elec- Existing harness Accessory harness Page 6 of 10 999Q5 KV100 II REV 1 12-10-09

Use caution when removing/re-installing interior components to avoid damage, scratches, or breaking of mounting clips. Type 2 Step 18d Type 1 Fig. 12 18) Attach ground. Fig. 12 a) Reconnect cluster bezel connector. b) Reinstall cluster bezel. c) Route housing wire harness pigtail as shown. Fig 12 d) Secure ground eyelet from housing wire harness with screw. Note: For vehicles with a Type 1 connector, secure the housing wire harness ground eyelet to the top right radio bracket in the 9 o clock position. For vehicles with a Type 2 connector, secure the housing wire harness ground eyelet to the top left radio bracket in the 3 o clock position. To avoid crushing the metal eyelet, do not overtighten the screw. Fig. 13 19) Install housing assembly strap and tighten fastener. Fig. 13 Page 7 of 10 999Q5 KV100 II REV 1 12-10-09

Fig. 14 20) Reconnect harness pigtail to the housing assembly. Fig. 14 Align Tabs Fig. 15 21) Install housing assembly. Fig 15 a) Push the harness connector below the opening between the radio and cluster lid. Ensure that the harness connector does not interfere with the housing assembly. b) Align the housing assembly mounting tabs with the mounting locations on the cluster lid, then press the housing into the cluster bezel. Fig. 18 Fig. 16 22) Housing installation is complete. Fig. 16 Page 8 of 10 999Q5 KV100 II REV 1 12-10-09

Fig. 17 23) Install the PND in the housing assembly. Fig. 17 a) Open the housing door. b) Fit the bottom of the PND into the cradle by aligning the pins. Rotate the PND toward the front of the vehicle until it clicks into place. Do not remove warning label from PND. c) Close the housing door. Page 9 of 10 999Q5 KV100 II REV 1 12-10-09

8. CHECKLIST: (1) Connect the battery negative terminal. (2) Turn the vehicle ignition switch to the ACC position and confirm the PND powers up. (3) Confirm audio through the mount speakers by adjusting the Navi volume up or down. Reset the default (80%) after volume confirmed. If no audio is present through the housing speakers, confirm the Navi unit volume is not muted, and the software is version 2.30 or greater. To show the current software version, select; Tools>Settings>System>About. If the Navi software version less than 2.30, a software update is required to make the unit compatible with this housing. (4) Turn the vehicle ignition OFF and confirm the PND powers down within 5 seconds. Close the housing lid. (5) Confirm for proper audio operation AM, FM, SAT, TAPE, and CD. (6) Clean the interior of the vehicle. (7) Inspect the vehicle interior and exterior for damage. (8) Confirm the proper operation of vehicle systems. (9) Reset radio presets to the recorded settings. (10) Place the PND Owner s Manual, Quick Start Manual, and accessories in the glove box. (11) If equipped, verify proper sunroof operation and perform the reset procedure, if necessary. Refer to Service Manual requirements. (12) Check the trim for a proper flush fit after re-installing the interior components. For installation or technical questions, contact Dealer Technical Support at 866-559-0074. Posi-Tap is protected by patent # 5,228,875 5,695,369 5,868,589 6,692,313 Jap 2881414 Aus 708700 Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562.9 & others pending. Page 10 of 10 999Q5 KV100 II REV 1 12-10-09