COVER VICINITY MAP SCOPE OF WORK ELECTRICAL NOTES GOVERNING CODES SHEET INDEX

SCOPE OF WORK TO INSTALL A SOLAR PHOTOVOLTAIC (PV) SYSTEM THE POWER ENERATED BY THE PV SYSTEM WILL BE INTERCONNECTED WITH THE UTILITY RID THROUH THE EXISTIN ELECTRICAL SERVICE EQUIPMENT. THE PV SYSTEM DOES NOT INCLUDE STORAE BATTERIES. ELECTRICAL NOTES 1.) ALL EQUIPMENT TO BE LISTED BY UL OR OTHER NRTL, AND LABELED FOR ITS APPLICATION. 2.) ALL CONDUCTORS SHALL BE COPPER, RATED FOR 600 V AND 90ºC WET ENVIRONMENT. 3.) WIRIN, CONDUIT, AND RACEWAYS MOUNTED ON ROOFTOPS SHALL BE ROUTED DIRECTLY TO, AND LOCATED AS CLOSE AS POSSIBLE TO THE NEAREST RIDE, HIP, OR VALLEY. 4.) WORKIN CLEARANCES AROUND ALL NEW AND EXISTIN ELECTRICAL EQUIPMENT SHALL COMPLY WITH NEC 110.26. 5.) DRAWINS INDICATE THE ENERAL ARRANEMENT OF SYSTEMS. CONTRACTOR SHALL FURNISH ALL NECESSARY OUTLETS, SUPPORTS, FITTINS AND ACESSORIES TO FULFILL APPLICABLE CODES AND STANDARDS. 6.) WHERE SIZES OF JUNCTION BOXES, RACEWAYS, AND CONDUITS ARE NOT SPECIFIED, THE CONTRACTOR SHALL SIZE THEM ACCORDINLY. 7.) ALL WIRE TERMINATIONS SHALL BE APPROPRIATELY LABELED AND READILY VISIBLE. 8.) MODULE ROUNDIN CLIPS TO BE INSTALLED BETWEEN MODULE FRAME AND MODULE SUPPORT RAIL, PER THE ROUNDIN CLIP MANUFACTURER'S INSTRUCTION. 9.) MODULE SUPPORT RAIL TO BE BONDED TO CONTINUOUS COPPER.E.C. VIA WEEB LU OR ILSCO BL-4DBT LAY-IN LU. 10.) THE POLARITY OF THE ROUNDED CONDUCTORS IS (positive/negative) OR THE DC SIDE OF THE PV SYSTEM IS UNROUNDED AND SHALL COMPLY WITH NEC 690.35. OVERNIN CODES 2013 NATIONAL ELECTRICAL CODE 2013 INTERNATIONAL BUILDIN CODE 2013 CALIFORNIA BUILDIN CODE 2013 CALIFORNIA ELECTRICAL CODE UNDERWRITERS LABORATORIES (UL) STANDARDS OSHA 29 CFR 1910.269 SHEET INDEX COVER PV-1 PLOT PLAN PV-2 ROOF LAYOUT/MOUNTIN DETAIL PV-3 ELECTRICAL 3-LINE DIARAM PV-4 AMPACITY CALCULATIONS PV-5 LABELS CUTSHEETS ATTACHED VICINITY MAP System Type: rid Tied Module Type: L285S1C-4 rid Voltage: 240V - - - - - - - - - - - - - - - - - - - - COVER

MAIN M INV M ATED FENCE System Type: rid Tied Module Type: L285S1C-4 PROPERTY LINE FENCE rid Voltage: 240V PROPERTY PLAN SCALE: 1 16"=1'-0" PV-1

46' 40'-2" 3' FIRE SETBACK INV M M MAIN SOLAR MODULE MODULE MOUNTIN CLAMP IRON RIDE RAIL J HOOK (E) FLAT TILE ROOF L-FOOT (E) 2x4 TOP CHORD 24" O.C. TRUSS FRAMIN SOLAR MOUNTIN DETAIL SCALE: 1 1 2" = 1'-0" SELF ADHISIVE BITUMOUS FLASHIN OR EQUIV. 5 16 " X 3" STAINLESS STEEL LA BOLT WITH 2-1/2" MIN PENETRATION SEALED WITH M-1 SEALANT OR EQUIVALENT M System Type: rid Tied Module Type: L285S1C-4 rid Voltage: 240V 3' FIRE SETBACK MAIN INV AC DC JB CB SUB LC A ROOF PLAN SCALE: 1 8" = 1'-0" 12'-2" 16'-6" M PV-2

Module Data (provided by manufacturer) Make of Model Model Number Max Power Point (MPP) Current (Impp) 8.88A Max Power Point (MPP) Voltage (Vmpp) 32.3V Open Circuit Voltage (Voc) 39.0V Short Circuit Current (Isc) 9.43A Max Series Fuse (OCPD) Max Power (Pmax) Max Voltage 15A 285W 1000V Inverter Data (provided by manufacturer) Make of Model Model Number Max DC Volt Rating Max Power @ 40 C Nominal AC Voltage Max AC Current SE5000A-US 500V 5000W 240V 21A Temperature Data from ASHRAE Average High Temp. (F ) 96.8 Record Low Temp. (F ) 26.6 String per Inverters 2 Number of Inverters 1 IMPORTANT BACKFED PV SOLAR BREAKER(S) SHALL BE INSTALLED AT THE END OF THE CIRCUIT OR FURTHEST AWAY FROM THE MAIN BREAKER. OPERATIN CURRENT: 8.88A OPERATIN VOLTAE: 350V MAX SYSTEM VOLTAE: 500V SHORT CIRCUIT CURRENT: 11.78A System Type: rid Tied Module Type: L285S1C-4 STRIN 1 + (2) 10 AW PVWIRE/USE-2 CONDUCTORS (1) 6 AW BARE Cu ROUND IN 3 4" EMT CONDUIT - + - + - (N)40A/2P-30A/2P PV QUAD BREAKER (E) 200A MAIN SERVICE PANEL & UTILITY METER NO MAIN BREAKER PANEL HAS LESS THAN 6 HANDLES L1 L2 N UTILITY RID 120/240V SINLE PHASE rid Voltage: 240V STRIN 2 + 1 10-1 STRIN OF 10 MODULES TOTAL OF 20 MODULES w/ SOLAREDE P300 POWER OPTIMIZERS + - + - 1 10 1 STRIN OF 10 MODULES TOTAL OF 20 MODULES w/ SOLAREDE P300 POWER OPTIMIZERS (N) SOLAREDE SE5000A-US INVERTER w / INTERAL DC/AC DISCONNECT + - + - (2) 10 AW THWN CONDUCTORS (1) 10 AW THWN NEUTRAL (1) 6 AW THWN ROUND 3/4" EMT CONDUIT OR EQUIVALENT L1 L2 N (N) SUNRUN PV METER 1 PHASE, 3W 600 VAC, 100A L1 L2 N L1 L2 N ROUND ROD N N N NOTE: DC IS UNROUNDED PV-3

System Type: rid Tied Module Type: L285S1C-4 # of Modules: 20 Inverter: SolarEdge SE5000A-US w/ Racking: Ironridge XR100 Solar Mounts: QuickScrew Tilehook DC Watts: 5.70 kw DC STC (E) Main Service Panel: 200A rid Voltage: 240V Roof Type: Flat Tile Array 1 Rafter Size: 2x4 Truss @ 24" O.C. Array 1 Pitch: Array 1 Azimuth: Array 1 Stories: 2 Avg. High Temp.: Rec. Low Temp: Module Weight (lb): 37.48 lbs. Avg. Standoff Spacing (ft): 6' Max. PV-4

SINAE REQUIREMENTS WARNIN IF A ROUND FAULT IS INDICATED, THE NORMALLY ROUNDED CONDUCTORS MAY BE ENERIZED AND UNROUNDED. REQ'D BY: NEC 690.5(C) 1 SMA AND SOLAREDE INVERTERS SYSTEM CHARACTERISTICS SYSTEM SIZE: kw SYSTEM OPEN CIRCUIT VOLTAE: VDC SYSTEM OPERATINN VOLTAE: VDC MAXIMUM ALLOWABLE DC VOLTAE: VDC SYSTEM OPERATIN CURRENT: AMPS SYSTEM SHORT CIRCUIT CURRENT: AMPS SOLAR DC DISCONNECT REQ' BY: NEC 690.14(C)(2) DC DISCONNECTS IF UTILIZED PHOTOVOLTAIC SYSTEM DISCONNECT AC CURRENT: A VOLTAE: 240 VAC > RED BACKROUND > WHITE LETTERIN > MIN. 3/8" LETTER HEIHT > ALL CAPITAL LETTERS > ARIAL OR SIMILAR FONT > REFLECTIVE, WEATHER RESISTANT MATERIAL, UL 969 2 SOLAR AC DISCONNECT REQ' BY: NEC 690.14(C)(2) AC DISCONNECTS 3 WARNIN ELECTRIC SHOCK HAZARD. DO NOT TOUCH TERMINALS. TERMINALS ON BOTH THE LINE AND LOAD SIDES MAY BE ENERIZED IN THE OPEN POSITION. REQ'D BY: NEC 690.17 DISCONNECTS SOLAR LOAD CENTERS COMBINER BOXES CAUTION DO NOT INSTALL ADDITIONAL LOADS IN THIS PANEL 4 System Type: rid Tied Module Type: L285S1C-4 RED'Q BY: NEC 690.53 INVERTER UPDATE VALUES WARNIN INVERTER OUTPUT CONNECTION. DO NOT RELOCATE THIS OVERCURRENT DEVICE 5 REQ'D BY: NEC 690.54 PV SYSTEM BREAKER UPDATE VALUES CAUTION SOLAR PV SYSTEM MAY REMAIN ENERIZED AFTER DISCONNECT DURIN DAYLIHT HOURS. 6 CAUTION: SOLAR CIRCUIT REQ'D BY: NEC 690.64(B)(2) 8 SOLAR LOAD CENTER IF UTILIZED WARNIN ELECTRIC SHOCK HAZARD. THE DC CONDUCTORS OF THE PV SYSTEM ARE UNROUNDED AND MAY BE ENERIZED. rid Voltage: 240V REQ'D BY: NEC 690.64(B)(7) PV SYSTEM BREAKER WARNIN THIS SERVICE IS SUPPLIED FROM MULTIPLE SOURCES UTILITY AND PHOTOVOLTAIC 9 REQ'D BY: AHJ MAIN SERVICE PANEL PHOTOVOLTAIC MICRO INVERTERS LOCATED UNDER EACH PV MODULE IN ROOFTOP ARRAY 10 REQ'D BY: AHJ SOLAR CONDUIT 11 REQ'D BY: NEC 690.35(F) UNROUNDED ARRAYS ONLY JUNCTION BOXES COMBINER BOXES DC DISCONNECTS INVERTERS 12 REQ'D BY: NEC 690.56(B) MAIN SERVICE PANEL 13 REQ'D BY: NEC 690.14(D) 14 MAIN SERVICE PANEL IF PV SYSTEM UTILIZES MICRO INVERTERS PV-5

System Type: rid Tied Module Type: L285S1C-4 rid Voltage: 240V Cutsheet