PARTS LIST AAT30/0 INTRAAX TRAILER SUSPENSION SYSTEM LIT NO: 974-0 DATE: March 06 REVISION: A SECTION PAGE Introduction... Axle and Suspension Identification... 3 Axle ID Plate... 3 Suspension Assembly Number Plate... 4 Ride Height Label... 4 Axle Assembly... Halftraax Assembly Components... Halftraax Spindle Identification... Frame Hanger & Pivot... 7 Frame Hanger Identification... 7 Air Springs & Hardware... 9 Air Spring Identification... 9 Shock Absorbers & Hardware Standard Hanger... Shock Absorbers & Hardware Tapered Hanger... 3 Axle Lift System - Hardware... 4 Axle Lift System Pneumatic Controls... Axle Rebound Limiters... 6 ARL System Identification... 6 Axle Rebound Limiter Trailing Arm Mounted... 7 Axle Rebound Limiter Axle Tube Mounted... 8 Axle Jounce Limiter Bump Stop... 9 Height Control Valve... 0 HCV System Identification... 0 Special Tools...
Introduction The purpose of this parts list is to document the available repair parts, accessories, special tools and lubricants available for the Hendrickson AAT30/0 INTRAAX (Integrated Trailer Axle) suspension systems. The major componentry included in this parts list is as follows: AAT30/0 INTRAAX Axle Assemblies (Halftraax); Air springs, relevant mounting hardware and fasteners; Shock Absorbers, relevant mounting hardware and fasteners; Frame Hangers; Quik-Align hardware and fasteners; Height Control Valve (HCV) system; and Axle lift system. This parts list should be used in conjunction with the following Intraax Family Parts Listings: 974-00 Trailer Wheel End Systems Parts List; and 974-097 Trailer Brake Systems Parts List. NOTE: All quantities listed within this parts list are as applicable for a single axle. 974-0 Rev A
Axle and Suspension Identification To assist with the identification of an Intraax axle or suspension system, reference should be made to the axle identification plate (refer to Figure ) and suspension assembly number plate (refer to Figure ). Figure Figure Axle ID Plate The axle ID plate is usually located on the inboard side of the left-hand trailing arm and provides the following key information: MODEL. DESCRIPTION. CUSTOMER PART NUMBER. AXLE SERIAL NUMBER. AXLE CAPACITY. The axle serial number (e.g. SK0060339) provides the following detail: Manufacturing Plant Identifier The first two digits of the axle serial number identify the manufacturing plant that originally manufactured the Halftraax Assembly as follows: SK Somerset Kentucky. LI Lebanon Indiana. CO Canton Ohio. Date of Manufacture The third to eighth digits of the axle serial number identify the date the Halftraax Assembly was manufactured in US date format (Year Month - Date) e.g. 006 Manufactured on 6 January 0 Manufacturing Sequence Number The final four digits (e.g. 0339) of the axle serial number provide the manufacturing sequence number. 3 974-0 Rev A
Suspension Assembly Number Plate The suspension assembly number plate is usually located on the inboard side of the right-hand trailing arm and provides the following: RIDE HEIGHT. ASSEMBLY PART NUMBER. DATE OF ASSEMBLY. Assembly Part Number The first six digits of the assembly part number identify the suspension system base model. The remaining digits identify specific options such as wheel end and brake system configuration. Base Model Identification Manufacturer (Digit ) Tri-Functional Bush Width (Digit ) Load Capacity (Digit 3 & 4) Model (Digit ) Specific Option Code (Digit 6) H= Hendrickson W = Wide (6 Inch) 3 = 3,000 lbs =, 000 lbs T = Top Mount See below. Specific Option Code (Digit 6) SOC Axle Track Brake Type Spindle type Axle Diameter K 73 Inch 6. Inch Drum HN Tapered.7 Inch (LDA) L 73 Inch 6. Inch Drum HP Parallel.7 Inch (LDA) M 73 Inch 370 & 430 mm Disc HN Tapered.7 Inch (LDA) Q 7. Inch 6. Inch Drum HN Tapered.7 Inch (LDA) V 73 Inch 4 mm Disc HP Parallel.7 Inch (LDA) Ride Height Label The ride height label (refer to Figure 3) should be affixed to the trailer frame by the trailer OEM. The label provides additional means of identification including system ride height and road friendly certification number. Figure 3 4 974-0 Rev A
Axle Assembly Halftraax Assembly Components All replacement AAT Drum Brake Halftraax axle assemblies are supplied complete with the following components: Tri-Function Bushes (TFB); S-Cams and tubes; Air spring pedestals (if applicable); Brake anchor pins and bushes; and Brake anchor and return springs. Refer to Figure 4 for detailed view of the AAT drum brake halftraax assembly as supplied. All replacement AAT Disc Brake Halftraax axle assemblies are supplied complete with the following components: Tri-Function Bushes (TFB);and Air spring pedestals (if applicable). Refer to Figure for detailed view of the AAT disc brake halftraax assembly as supplied. Figure 4 Figure Halftraax Spindle Identification AAT Intraax suspension systems are available with HN (Tapered) and HP (Parallel) type spindles. Refer to Figure 6. HN Spindle HP Spindle Figure 6 974-0 Rev A
Axle Assembly Item Part Number Description Qty Notes INTSUSP.40 Halftraax Assy, AAT30 7. Inch Track HN, Disc Brake. EINTSUSP.347 Halftraax Assy, AAT0 7. Inch Track HN, 6. Inch Drum Brake. EINTSUSP.3446 Halftraax Assy, AAT0 7. Inch Track HP, 6. Inch Drum Brake. EINTSUSP.39 Halftraax Assy, AAT30 73 Inch Track HN, 370/430 MM Disc Brake Except Inch Ride Height. 9844-67 Halftraax Assy, AAT30 73 Inch Track HN, 370/430 MM Disc Brake Inch Ride Height. EINTSUSP.349 Halftraax Assy, AAT30 73 Inch Track HN, 6. Inch Drum Brake Except Inch Ride Height. 9844-08 Halftraax Assy, AAT30 73 Inch Track HN, 6. Inch Drum Brake Inch Ride Height. EINTSUSP.34 Halftraax Assy, AAT0 73 Inch Track HN, 6. Inch Drum Brake Except Inch Ride Height. 9844-09 Halftraax Assy, AAT0 73 Inch Track HN, 6. Inch Drum Brake Inch Ride Height. EINTSUSP.308 Halftraax Assy, AAT0 73 Inch Track HP, MAXXT Disc Brake Except Inch Ride Height.. 9844-34 Halftraax Assy, AAT0 73 Inch Track HP, MAXXT Disc Brake Inch Ride Height.. EINTSUSP.343 Halftraax Assy, AAT0 73 Inch Track HP, 6. Inch Drum Brake Except Inch Ride Height.. 9844-0 Halftraax Assy, AAT0 73 Inch Track HP, 6. Inch Drum Brake Except Inch Ride Height.. NOTE: All halftraax axle assemblies listed above are the latest.7 Inch Large Diameter Axle (LDA). When using a LDA Halftraax to replace an earlier.00 Inch type, brake dust shields and clamps, will also require replacement. Refer to 974-097 Intraax Brake System Part List for further detail. 6 974-0 Rev A
Frame Hanger & Pivot Frame Hanger Identification To determine the applicable frame hanger for a specific suspension, the hanger drop will often need to be determined. Frame drop is the measurement in millimetres from the underside of the trailer frame to the centre of the pivot bolt hole. Refer to dimension A in Figure 7. Frame hangers are available in both standard and tapered configuration. Refer to Figure 8 for pictorial comparison of standard (view A) and tapered (view B) frame hanger designs. Figure 7 A B Figure 8 7 974-0 Rev A
Frame Hanger & Pivot 3 4 6 7 0 8 9 4 3 Item Part Number Description Qty Notes S-08- Frame Hanger, RH Standard S-08- Frame Hanger, LH Standard 03 mm Drop except Inch Ride Height. 03 mm Drop except Inch Ride Height. 98938-8 Frame Hanger, RH Standard 03 mm Drop & Inch Ride Height. 98938-7 Frame Hanger, LH Standard 03 mm Drop & Inch Ride Height. S-08- Frame Hanger, RH Standard 4 mm Drop. S-08- Frame Hanger, LH Standard 4 mm Drop. 98938-00 Frame Hanger, RH Tapered 4 mm Drop. 98938-049 Frame Hanger, LH Tapered 4 mm Drop. S-083- Frame Hanger, RH Standard 30 mm Drop. S-083- Frame Hanger, LH Standard 30 mm Drop. 98870-06 Brace Channel, Hanger Support Suits 4 & 30 mm drop. 3 NSS Shear Bolt Quik-Align Use Item 3 or 4. 4 NSS Hardened Washer 7/8 Inch 4 Use Item 3 or 4. C-094 Flanged Washer, Inner Quik-Align Concentric. Use Item 3. 6 C-09 Flanged Washer, Outer Quik-Align Eccentric. Use Item 3. 7 NSS Nut, Prevailing Torque 7/8 UNC Use Item 3 or 4. 8 A-40 Lube Pack, Tri-Functional Bush 9 S-6-4P Kit - Wear Bushing, Glove Style 0 S-099-4P Kit Wear Bushing, Flat NSS Bush, Tri-Functional Use Item. S-364 Kit, Tri-Functional Bush Includes Items 3, 4, 7, 8, 0 &. 3 S-36 Kit, Quik Align Includes Item 3, 4,, 6 & 7. 4 S-363 Kit, Pivot Bolt Includes Items 3, 4 & 7. 8 974-0 Rev A
Air Springs & Hardware Air Spring Identification To assist with the correct air spring identification a visual inspection of the air spring is recommended. There are two air spring identification markings: The air spring part number is provided on a decal on the upper bead-plate (refer to Item in Figure 9); and Moulded into the air spring rubber bellows (refer to Item in Figure 9). Figure 9 9 974-0 Rev A
Air Springs & Hardware 3 4 6 0 9 7 8 0 974-0 Rev A
Air Springs & Hardware Item Part Number Description Qty Notes S-30- Frame Spacer, Air Spring 03 MM 9 Inch Ride-height Except Liftable. S-30-6 Frame Spacer, Air Spring 3 MM 9 Inch Ride-height Liftable. SA-300-3 Plug, Air Fitting /4 NPT Included in Item. 3 NSS Air Fitting Air Spring AR Use Item. 4 B-090 Frame Plate, Air Spring - Upper Mount Except 9 Inch Ride-height. S-0- Spacer, Air Spring 9 MM Inch Ride-height. S-0- Spacer, Air Spring 48 MM 6 Inch Ride-height. S-0- Spacer, Air Spring 48 MM 7 Inch Ride-height Liftable except MAXXT. S-0-3 Spacer, Air Spring 80 MM 7 Inch Ride-height Except Liftable. S-0-3 Spacer, Air Spring 80 MM 7 Inch Ride-height MAXXT. S-800 Air Spring Assy AAT30 Except Inch Ride-height 6 C-090 Air Spring Assy AAT0 Except Inch Ride-height S-6773 Air Spring Assy Inch Ride-Height. 7 SA-7000- Nut, Flanged Air Spring / x 3. Included in Item. 8 SA-6900- Bolt, Flanged - Air Spring Pedestal 4 3/8 x 6 UNC. NSS Pedestal, Air Spring RH Welded Type. See Note. NSS Pedestal, Air Spring LH Welded Type. See Note. 9 NSS Pedestal, Air Spring RH Bolted type. 49 MM. Use Item. NSS Pedestal, Air Spring LH Bolted type. 49 MM. Use Item. NSS Pedestal, Air Spring RH Bolted type. 74 MM. Use Item. NSS Pedestal, Air Spring LH Bolted type. 74 MM. Use Item. 0 SA-7000-3 Nut, Flanged - Air Spring Pedestal 4 3/8 UNC. S-364-R Kit, Air Spring Pedestal RH 49 MM. Includes Items 8, 9 & 0. S-364-L Kit, Air Spring Pedestal LH 49 MM. Includes Items 8, 9 & 0. S-364-R Kit, Air Spring Pedestal RH 74 MM. Includes Items 8, 9 & 0. S-364-L Kit, Air Spring Pedestal LH 74 MM. Includes Items 8, 9 & 0. S-907/ Hardware Kit Air Spring Inch Ride-height. Includes Item, 3 & 7. S-69 Hardware Kit Air Spring 3. Inch Ride-height. Includes Item, 3 & 7. S-630 Hardware Kit Air Spring Inch Ride-height Except Liftable. Includes Item, 3 & 7. S-69 Hardware Kit Air Spring Inch Ride-height Liftable. Includes Item, 3 & 7. S-63 Hardware Kit Air Spring 6 Inch Ride-height. Includes Item, 3 & 7. S-63 Hardware Kit Air Spring 7 Inch Ride-height Except Liftable. Includes Item, 3 & 7. S-63 Hardware Kit Air Spring 7 Inch Ride-height Liftable. Includes Item, 3 & 7. S-69 Hardware Kit Air Spring 9 Inch Ride-height Liftable. Includes Item, 3 & 7. NOTE: Early design halftraax axle assemblies were manufactured with welded type air-spring pedestals which are not available as a service part. Bolted type air-spring pedestals CANNOT be used to replace welded type. 974-0 Rev A
Shock Absorbers & Hardware Standard Hanger 4 3 6 9 8 7 0 Item Part Number Description Qty Notes S-098 Clevis, Shock Mount Upper NSS Bolt, Shock Absorber Upper 3/4-0UNC x 3. Inch. Use Item 4. 3 NSS Nut, Shock Absorber Upper 3/4-0UNC. Use Item 4. 4 98-03 Bolt Kit, Shock Absorber Mounting Includes Items, 3, 7, 8 & 9. 9898-0 Kit, Lower Shock Support Bracket Includes Items 0, &. S-699 Shock Absorber - Standard Road Friendly. 6 9883-0 Shock Absorber Heavy Duty Road Friendly. S-0889 Shock Absorber Non-Road Friendly. 7 NSS Shock Absorber Spacer, Cast Use Item 4. 8 NSS Washer, Hardened 6 3/4 Inch. Use Item 4. 9 NSS Bolt, Shock Absorber Lower 3/4-0UNC x.7 Inch. Use Item 4. 0 B-300 Nut Plate, Lower Shock Support Bracket B-3037- Bracket, Lower Shock Support, LH B-3037- Bracket, Lower Shock Support, RH SA-6900- Bolt, Lower Shock Support Bracket 3/8-6 x.. 974-0 Rev A
Shock Absorbers & Hardware Tapered Hanger 4 3 6 8 7 9 0 Item Part Number Description Qty Notes NSS Nut, Shock Absorber Upper 3/4-0UNC. Use Item 4. NSS Bolt, Shock Absorber Upper 3/4-0UNC x 0. Inch. Use Item 4. S-699 Shock Absorber Standard Road Friendly. 3 9883-0 Shock Absorber Heavy Duty Road Friendly. S-0889 Shock Absorber Non-Road Friendly. 4 98-06 Bolt Kit, Shock Absorber Mounting Includes Items,, 6, 7 & 8. 9898-0 Kit, Lower Shock Support Bracket Includes Items 9, 0 &. 6 NSS Shock Absorber Spacer, Cast Use Item 4. 7 NSS Washer, Hardened 6 3/4 Inch. Use Item 4. 8 NSS Bolt, Shock Absorber Lower 3/4-0UNC x.7 Inch. Use item 4. 9 B-300 Nut Plate, Lower Shock Support Bracket 0 B-3037- Bracket, Lower Shock Support, LH B-3037- Bracket, Lower Shock Support, RH SA-6900- Bolt, Lower Shock Support Bracket 3/8-6 x.. 3 974-0 Rev A
Axle Lift System - Hardware 0 3 4 6 7 8 9 Item Part Number Description Qty Notes S-4343 Kit Axle Lift, AAT S-464 Kit, Fastener Axle Lift See Note. Includes Items 7, 8, 9 &. 3 D-330C Bracket Assy Hanger Support 4 S-34 Air Spring Axle Lift B-794 Plate Assy Beam, Air Spring 6 S-399C Bracket Assy Beam, Air Spring 7 NSS Bolt, Plate to Bracket /-3 X. 4 Use Item. 8 NSS Bolt, Air Spring to Plate 3/8-6 x 0.7 4 Use Item. 9 NSS Nut, Plate to Bracket /-3 4 Use Item. 0 S-90-37 Gusset, Hanger Support Bracket 4 S-490- Nut, Air Spring 3/4-6 Spiralock Included in Item. NOTE: The fastener kit (part no. S-464) includes four self-tapping screws. These are only required during initial system installation and MUST be removed and discarded once system installation is complete. 4 974-0 Rev A
Axle Lift System Pneumatic Controls 3 4 Item Part Number Description Qty Notes 9897-0 Kit, Pneumatic Control - Lift Axle Auto Raise, Auto Lower. 9897-0 Kit, Pneumatic Control - Lift Axle Manual Raise, Auto Lower. See note. NSS Case, Steel Lift Axle Controls Use Item. 9897-00 Valve, Control Lift Axle Auto Raise, Auto Lower. 3 9897-004 Valve, Control Lift Axle Manual Raise, Auto Lower. 4 9840-003 Valve, Manual Over-ride Lift Axle Auto Raise, Auto Lower. See Note. NOTE: The manual over-ride valve is only installed in auto raise, auto lower type lift axle control systems. For the manual raise, auto lower type lift axle control system, the manual over-ride mechanism is incorporated into the lift axle control valve. 974-0 Rev A
Axle Rebound Limiters ARL System Identification The AAT Intraax suspension axle rebound limiters (ARL) are available in two types of configurations: Frame to Trailing Arm Mounted. Shock Clevis to Axle Tube Mounted. Frame to Trailing Arm Mounted ARL Frame to trailing arm type ARL is available in either chain or strap configuration, and utilises a lower clevis mounted to an extension assembly at the rear of the trailing arm, and an upper clevis mounted to the underside of the trailer frame channel (refer to Figure 0). Shock Clevis to Axle Tube Mounted ARL Shock clevis to axle tube type ARL is only available in strap configuration, which is routed around the axle tube and mounts to the upper shock clevis (refer to Figure ). Figure 0 Figure NOTE: For information regarding shock absorber straps, refer to Technical Bulletin 974-0. 6 974-0 Rev A
Axle Rebound Limiter Trailing Arm Mounted 9 8 7 7 6 6 3 4 Item Part Number Description Qty Notes 9898-00 Kit, ARL Strap Type 3. & Inch Ride height. 9898-006 Kit, ARL Strap Type 6 & 7 Inch Ride height. 9898-007 Kit, ARL Strap Type 9 Inch Ride height. 9898-03 Kit, ARL Chain Type 3. & Inch Ride height. 9898-04 Kit, ARL Chain Type 6 & 7 Inch Ride height. 9898-0 Kit, ARL Chain Type 9 Inch Ride height. S-404-8 Strap, ARL 3. & Inch Ride height. 3 S-404- Strap, ARL 6 & 7 Inch Ride height. S-404- Strap, ARL 9 Inch Ride height. SA-9600- Chain, ARL / x Link 3. & Inch Ride height. 4 SA-9600-3 Chain, ARL / x 3 Link 6 & 7 Inch Ride height. SA-9600-4 Chain, ARL / x 4 Link 9 Inch Ride height. B-30840- Trailing Arm Extension, - LH B-30840- Trailing Arm Extension, - RH 6 47764-000 Bolt - Extension to Trailing Arm 8 /8 UNC x. Inch. 3043-00 Nut, Lock Extension to Trailing Arm 8 /8 UNC. 7 S-473 Clevis, ARL - Upper 8 NSS Bolt - ARL Clevis 4 3/4 x 3. 0 UNC Grade. Use Item 0. 9 NSS Nut, Lock - ARL Clevis 4 3/4 0 UNC. Use Item 0. 0 A-003 Fastener Kit ARL Clevis Includes Items 8 & 9. S-093-4 Spacer, ARL Strap 4 Suits Strap Type. 7 974-0 Rev A
Axle Rebound Limiter Axle Tube Mounted 4 7 3 6 Item Part Number Description Qty Notes 9898-00 Kit, Axle Rebound Limiter 6, 7 & 9 Inch Ride Height. 989-004 Strap, Restraining - ARL 3 3043-00 Bolt ARL Strap to Bracket /8 UNC x.7 Inch. 4 96-004 Washer, Hardened ARL Strap to Bracket 4 /8. 96-004-4P Pack, Hardened Washer Includes 4 of 96-004. 47764-000 Nut, Lock ARL Strap to Bracket /8 UNC. 6 98899-00 Bracket ARL Strap Mounting, RH 98899-003 Bracket ARL Strap Mounting, LH 7 98766-003 Bolt Shock Absorber, Upper 3/4 UNC x 4 Inch. 4984-000 Nut, Lock Shock Absorber, Upper 3/4 UNC. NOTE: The axle tube mounted ARL Kit (Part No. 9898-00) is NOT suitable for use with tapered type frame hangers or LDA (Large Diameter Axle). 8 974-0 Rev A
Axle Jounce Limiter Bump Stop 3 4 6 Item Part Number Description Qty Notes 98708-0 Kit, Bump Stop Inch Ride Height. 98708-06 Kit, Bump Stop 7 Inch Ride Height. 98708-07 Kit, Bump Stop 9 Inch Ride Height. 98708-0 Bracket, Frame Bump Stop Inch Ride Height. 98708-03 Bracket, Frame Bump Stop 7 Inch Ride Height. 98708-04 Bracket, Frame Bump Stop 9 Inch Ride Height. 3 49846-000 Nut, Lock Bump Stop to Bracket 4 / Inch UNC Grade 8. 4 43-00 Bolt Bump Stop to Bracket 4 /-3 UNC x 6 / Inch. 96-0 Washer, Hardened 8 / Inch. 6 6034-000 Bump Stop, Rubber 9 974-0 Rev A
Height Control Valve HCV System Identification For AAT Intraax suspension systems, the Height Control Valve (HCV) components are common regardless of configuration, with the following exceptions: The HCV mounting bracket varies between standard & tapered hanger. For standard hanger the bracket mounts to the upper shock absorber clevis (Refer to View A & C). For tapered hanger the bracket mounts directly onto the inside of the hanger (Refer to View B); The lower linkage mounting bracket is available in three variations as follows: o o o Fixed to the brake chamber bracket (Refer to View A); Fixed to the axle tube (Refer to View B); Fixed to the lower shock absorber bracket (Refer to View C). View A View B View C Figure 0 974-0 Rev A
Height Control Valve 3 4 6 7 0 9 8 Item Part Number Description Qty Notes 600-000 Height Control Valve Assy See Note. 98677-007 Bracket, HCV Mounting Tapered Hanger. 797-000 Bracket, HCV Mounting Standard Hanger. 693-00 Bolt - HCV Bracket /4 0 UNC x Inch. 3 96-08 Washer, Hardened HCV Bracket 4 /4 Inch. SA-9000-6 Nut, Lock HCV Bracket 4 /4 UNC. 4 98934-03 Air Fitting, 90 Degree 3 3/8 OD x /4 Inch NPT. S-480 Hose Fitting, Barbed Plastic /4 NPT. S-48 Hose, Plastic HCV /4 ID x 4 Inch. 6 S-487 Link Assy, Bolted HCV Includes Fasteners. 7 S-693- Clamp, Bracket - HCV Link.00 Inch Axle Tube Mounted. S-693- Clamp, Bracket - HCV Link.7 Inch Axle Tube Mounted. 8 S-393 Bracket, Lower HCV Link Axle Tube Mounted. 9 98677-00 Bracket, Lower HCV Link Shock Bracket Mounted. 0 S-477 Bracket, Lower HCV Link Chamber Bracket Mounted. A-8 Valve, Pressure Protection SA-300-3 Plug, Pipe /4 NPT. NOTE: The HCV assembly (Part no. 600-000) includes the lever arm. The nut that retains the lever arm to the HCV shaft is coated with a thread locking compound and MUST NOT be removed. Any attempt to remove the nut will most likely result in fracture of the HCV shaft. 974-0 Rev A
Special Tools 3 9 4 6 7 8 Item Part Number Description Qty Notes S-4303 Socket, Pivot Bolt E0 3/4 Inch Drive. S-436 Socket, Pivot Bolt E0 Inch Drive Standard Duty. S-9 Socket, Pivot Bolt E0 Inch Drive Heavy Duty- Production. S-307A Tool Kit Tri-Functional Bush, Wide See Note. 3 S-308 Bolt, Acme Thread 8 Inch 4 9876-00 Bearing, Thrust TFB Tool S-3 Plate, Front TFB Tool 6 S-33 Tube, Transition TFB Tool 7 S-34 Spacer, Removal TFB Tool 8 S-309 Plate, Rear Drive TFB Tool 9 SA-800-4 Set Screw /-3 x 4 inch Removal only. 9 SA-800-7 Set Screw /-3 x inch Installation only. 0 S-337 Grease, Extreme Pressure Not Illustrated. See Note. S-344 Gauge, Ride Height 3. to 9 Inch S-344 Gauge, Ride Height 6. to 4 Inch NOTE: The Tri-functional tool kits are supplied with one tube of extreme pressure grease. 974-0 Rev A
Revisions Table DATE REV PAGE DESCRIPTION Information contained in this literature was accurate at the time of publication, Product changes may have been made after the publication date that are not reflected here. HENDRICKSON ABN 004 99 769 3-44 Letcon Drive, P.O. Box 063, Dandenong, Victoria, 37 Phone 6.3.879.3600 Fax 6.3.879.3699 www.hendrickson.com.au 974-0 Rev A THE BOLER COMPANYCOPYRIGHT 04