Catalog number: Approvals: / / / / Mtg. Fixture Electrical Module Finish Options See page 4 See page 2 See page 3 Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting. Date: Page: of 5 Specifications Housing: Spun aluminum. (Rollformed linear reveals; : Three equally spaced reveals, K" wide, separated by K" ribs, J" deep. S: 2" Diameter 20 Light Emitting Diodes Total Max System Watts = 40W 0" (254.0 mm) 9K" (24.3 mm) 2" DIA. (533.4 mm) 6L" DIA. (7.5 mm) S One J" groove, J" deep.) Sidewalls have a maximum of taper, and are free of welds or fasteners. A rollformed aluminum flange is hemmed into the bottom providing support for the reflector module. An internal aluminum casting provides for mounting of the electrical module and support for the housing hinge. Lens Frame and Yoke: One-piece cast aluminum lens frame is attached to the housing by a zinc plated cold rolled steel hinge with a stainless steel pin. Closure of the housing is by three self-retained stainless steel screws. A stainless steel self-locking stop arm is provided to hold the housing in the open position while servicing. A F" thick clear flat tempered glass lens is fully gasketed by a one-piece extruded and vulcanized silicone gasket. Lens is retained in the frame by removable zinc plated steel clips. Lens frame is supported at four points by two aluminum U-shaped tubular arms cradled in a cast aluminum hub. Arms are welded to the lens frame, and welded to the hub along their longitudinal axis. Hub contains a field-splice compartment, a cast aluminum cover and one of the following pole attachment means: FM - Flush Mounting, PT - Pole Tenon mounting, or DM - Direct Mounting (See page 2 for complete descriptions). Electronic Module: All electrical components are UL and CSA recognized, mounted on a single plate and factory prewired with quick-disconnect plugs. Module includes a driver, LifeShield temperature control device and surge protector. Electrical module attaches to housing with key hole slots, accessible by opening the lens frame and removing optical module. Driver is rated for -40 F starting and has a 0-0V dimming interface for multi-level illumination options. Optical Module: Precision, replaceable MicroEmitter reflectors are positioned to achieve directional control toward desired task. The entire EmitterDeck mounting assembly fastens to the housing as a one-piece module. Finish/Color: Finish is TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness. Standard colors are Black, Dark Bronze, Light Gray, Stealth Gray, Platinum Silver, or White. Custom colors are available. Warranty: Kim Lighting warrants Curvilinear LED products ( Product(s) ) sold by Kim Lighting to be free from defects in material and workmanship for (i) a period of five (5) years for metal parts, (ii) a period of ten (0) years for exterior housing paint finish(s), (iii) a period of six (6) years for LED Light Engines (MicroEmitters) and, (iv) a period of five (5) years for LED power components (LED Driver, LifeShield temperature control device, surge protector), from the date of sale of such goods to the buyer as specified in Kim Lighting shipment documents for each product. CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. Listings and Ratings ETL UL 598, UL 8750 Suitable for wet locations. KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE.
Page: 2 of 5 Standard Features Mounting EPA:.0.0.0 Cat. No.: FM Flush Mount PT Pole Tenon Mount DM Direct Mount Pole Top 4", 4K", 5", or 6" Dia. 2" Pipe-size Tenon 3." to 3.9" Dia. Requirements: (2C" O.D. x 4L" L) Fixture Cat. No. designates /S fixture and light distribution. See the Kim Site/Roadway Optical Systems Catalog for detailed information on reflector design and application. Housing: S Size: 2 = 2 Large 20 LEDs P = Post Top Mount 2 P x Distribution: = Type I Full Cutoff 2 = Type II Full Cutoff 3 = Type III Full Cutoff 4 = Type IV Full Cutoff 5 = Type V Square Full Cutoff L = Type L Left Full Cutoff R = Type R Right Full Cutoff Light Distribution: Type I Type IV Forward Throw Type II Type V Square Type III Type R Right Type L Left
Page: 3 of 5 Standard Features Electrical Module Cat. Nos. for Electrical Modules available: 20 LxK x NOTE: Curvilinear system employs Nichia s SSL product. Part number: NS6x83 (NS6L83-H3,NS6W83-H3) Source: 20 = 20 LED s Color Temperature: L3K = 3500K L5K = 500K L2K = 580nm - Amber Voltage: 20 = 20V 208 = 208V 240 = 240V 277 = 277V 347 = 347V 480 = 480V 4300K and 6500K are also available on an Engineered-to-Order (ETO) basis. Fixture Total System Watts Volt Operating Amps /S 2 LED 40 20.7 /S 2 LED 40 208 0.67 /S 2 LED 40 240 0.58 /S 2 LED 40 277 0.5 /S 2 LED 40 347 0.40 /S 2 LED 40 480 0.29 Watt, volt and amps are based on max assumptions, rather than thermal in situ testing. Finish TGIC powder coat paint over a titanated zirconium conversion coating. Color: Black Dark Bronze Light Gray Stealth Gray Platinum Silver White Custom Color Cat. No.: BL DB LG SG PS WH Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description:
Page: 4 of 5 Optional Features Photocell Cat. No. (See right) Factory installed photocell inside housing with a fully gasketed sensor on the side wall. Cat. No. A-30 A-3 A-32 Line Volts: 20V 208V 240V Cat. No. A-33 A-35 A-34 Line Volts: 277V 347V 480V Photocell Sensor Dimming Controls The Curvilinear LED driver is a 0-0V dimming interface, allowing 0-00% illumination output when synchronized with a control and dimming system, provided by others. Kim Lighting is working with several control system manufacturers to develop a variety of proven turnkey solutions to meet any application s need. Kim Lighting will advise availability of complete control packages, and even two-way monitoring systems, once they have been tested and exceed Kim s high quality standards. Convex Glass Lens Cat. No. CGL The F" thick clear convex tempered glass lens replaces standard flat glass lens. Provides increased lens presence and provides a subtle improvement in uniformity where pole spacing is extreme. Increases effectiveness of houseside shielding. 3J" (82.6 mm) Convex Glass Lens Polycarbonate Lens Cat. No. L2F Clear UV stabilized polycarbonate replaces standard flat glass lens, gasketed and integral with lens frame. CAUTION: Use only when vandalism is anticipated to be high. Useful life is limited by UV discoloration from sunlight. Polycarbonate Lens Accent Reveals Cat. No. (See right) (For series only.) Three aluminum bands riveted inside the housing reveals. Available in five standard Kim powder coat finishes. Custom colors available. Accent Reveals Color: Black Dark Bronze Light Gray Stealth Gray Platinum Silver White Custom Colors Cat. No.: BL-REV DB-REV LG-REV SG-REV PS-REV WH-REV -REV Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description:
Page: 5 of 5 Lumen Performance Charts NOTES:. Lumen loss stablization is a result of Kim Lighting s MicroEmitter luminaires exclusive LifeShield temperature control device and Dual Heat Management. 2. The LifeShield temperature control device will lower the current to the LEDs significantly if the luminaire is exposed to direct heat (sun) or excessive abnormal conditions. 3. Luminaire Lumen Loss assumptions are based on LM- 80 results and an actual outdoor product testing based upon 500K T, 350mA drive current. 25 C/77 F tab ambient and cathode temperature at 85 C/85 F. Assumptions past 6,000 hours are interpolated. 4. Cathode temperature baseline is at 85 C/85 F. If cathode temperature increases during ambient changes and abnormal environment conditions, % of rated lumens will slightly decrease. 5. Outdoor ambient temperatures are assumed SITU average by geographic region. 6. As Solid State Lighting technology and thermal management systems continually advance, lumen loss projections are subject to improvement. Lumen Percentage % of Rated Luminaire Lumens 0 00 90 80 70 60 50 40 30 20 20 0 00 90 80 L-70 Luminaire Lumen Loss by Hours of Operation Hours of Operation 0000 20000 30000 40000 50000 60000 70000 80000 90000 00000 Outdoor Temperature at 0 C/50 F. Temperature is based on continual average, annual assumptions. Outdoor Temperature at 40 C/04 F. Temperature is based on continual average, annual assumptions. Luminaire Output at Outdoor Ambient Temperatures Stabilizes Output Due to Exclusive LifeShield Protection System Hazardous Thermal Environment 70-20 C -4 F -0 C 4 F 0 C 32 F 0 C 50 F 20 C 68 F 25 C 77 F 30 C 86 F 35 C 22 F 40 C 95 F 45 C 04 F 50 C 22 F 55 C 32 F 60 C 40 F 65 C 49 F 70 C 58 F