Table of Contents Post Hole Digger SA30 & SA35 19221 317-093P Parts Manual Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2011 Printed 04/01/11 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Frames - SA30/35 (Post Hole Diggers)...6 Gearbox Housing...6 Hitch...8 Section 3: Gearboxes - SA30/35 (Post Hole Diggers)...10 Gearbox (826-313C) (826-314C)...10 Section 4: Hydraulic Motor - SA30 (Post Hole Diggers)...12 Hydraulic Motor (810-427C) S/N 458502-...12 White Hydraulic Motor (810-530C) S/N 458503+...14 Section 4: Hydraulic Motor - SA35 (Skid Steer Mount)...16 Hydraulic Motor (810-424C) S/N 459700-...16 White Hydraulic Motor (810-531C) S/N 459701+...18 Section 5: Labels - SA30/35 (Post Hole Diggers)...20 Label Placement...20 Section 6: Options & Accessories - SA30/35 (Post Hole Diggers)...22 Auger...22...24 Copyright 201 All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents A G H L W Auger...22 Gearbox (826-313C) (826-314C)...10 Gearbox Housing...6 Hitch...8 Hydraulic Motor (810-424C) S/N 459700-...16 Hydraulic Motor (810-427C) S/N 458502-...12 Label Placement...20 White Hydraulic Motor (810-530C) S/N 458503+...14 White Hydraulic Motor (810-531C) S/N 459701+...18 Alphabetized Table of Contents 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 3
Table of Contents 4 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 5
Gearbox Housing Applies to SA30, SA35 Table of Contents Section 2: Frames - SA30/35 (Post Hole Diggers) 19241 6 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Gearbox Housing Section 2: Frames - SA30/35 (Post Hole Diggers) Applies to SA30, SA35 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 7. 7. 7. 8. 8. 9. 10. 1 1 1 14. 15. 16. dwg19241 805-312C 317-086H 805-058C 802-057C 802-091C 804-015C 810-531C 810-424C 810-530C 810-427C 826-313C 826-314C 804-022C 803-021C 811-778C 811-779C 811-205C 811-745C 811-744C 811-091C Drawing Image Number PIN CLEVIS 1 1/4 X 6 7/8 USBL HYD. AUGER MOUNT WELD., PLANET PIN COTTER 3/16 X 2 HHCS 5/8-11X2 1/4 GR5 HHCS 1/2-13X1 1/2 GR5 WASHER LOCK SPRING 1/2 PLT HYD MTR 18 CU IN DSP W/14T SPL HYD MTR 18 CU IN DSP SA SERIES HYD MTR 12 CU IN DSP W/14T SPL HYD MTR 12 CU IN DSP SA SERIES GBOX 75:1 14T PLNTRY 2 9/16 GBOX 75:1 14T PLNTRY 2 HEX WASHER LOCK SPRING 5/8 PLT NUT HEX 5/8-11 PLT EL 45 7/8MORB 3/4MJIC HH1/2R2 096 3/4FJIC E-Z FLEX AD 3/4MJIC 1 1/16MORB CP 1 1/16FORB FEMALE QUICK CP 1 1/16FORB MALE QUICK EL 3/4MJIC 1 1/16MORB S/N 610954+ Painted Black SA35 S/N 459701+ SA35 S/N 459700- SA30 S/N 458503+ SA30 S/N 458502- S/N 610954+ Painted Black S/N 610954+ Painted Black As Required As Required 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 7
Hitch Applies to SA30, SA35 Table of Contents Section 2: Frames - SA30/35 (Post Hole Diggers) 19240 8 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Section 2: Frames - SA30/35 (Post Hole Diggers) Hitch Applies to SA30, SA35 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. dwg19240 317-084H 804-011C 803-013C 807-023C 805-058C 317-085H 800-080C 805-311C 802-017C Drawing Image Number HYDRAULIC AUGER HITCH WELDMENT WASHER FLAT 3/8 USS PLT NUT LOCK 3/8-16 PLT SPRING HOSE LOOP PIN COTTER 3/16 X 2 HYD. AUGER CLEVIS WELDMENT GREASE ZERK 1/4-28 THD FORMING PIN CLEVIS 1 1/4 X 6 USABLE HHCS 3/8-16X1 GR5 S/N 610954+ Painted Black S/N 610954+ Painted Black S/N 689255+ 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 9
Table of Contents Gearbox (826-313C) (826-314C) Section 3: Gearboxes - SA30/35 (Post Hole Diggers) Applies to SA30, SA35 19242 10 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Gearbox (826-313C) (826-314C) Section 3: Gearboxes - SA30/35 (Post Hole Diggers) Applies to SA30, SA35 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 dwg19242 826-313C 826-314C 040436 040429 060120 050209 050208 140001 010220 050206 050207 090259 130098 120089 060119 030447 180193 030568 130120 020280 140062 130058 110187 130060 110213 Drawing Image Number GBOX 75:1 14T PLNTRY 2 9/16 GBOX 75:1 14T PLNTRY 2 HEX * OMNI SHAFT - A2 OMNI SHAFT - H2 OMNI OIL SEAL (CR37053) OMNI BEARING CONE (JM714249A) OMNI BEARING CUP (JM714210) OMNI PIPE PLUG 1/8 SOCKET HD OMNI HOUSING H2 NO BRAKE HOLES OMNI BEARING CUP (32214) OMNI BEARING CONE (32214) OMNI SPACER FLAT TONGUED OMNI LOCK NUT WASHER, M70 OMNI LOCK NUT M70X2 OMNI O-RING OMNI GEAR RING 77T OMNI SECONDARY CARRIER SUB ASY OMNI GEAR SUN 28T OMNI RETAINING WASHER, SUN OMNI CAP INPUT OMNI PIPE PLUG, 3/8"-18NPT MAG OMNI LOCKWASHER, M8 SPLIT TYPE OMNI HEX BOLT, M8X25 GR10.9 OMNI LOCK WASHER M10 OMNI SOCKET HEAD BOLT M10X25 2 9/16" Dia. Round Shaft 2" Hex Shaft (826-313C) (826-314C) 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 11
Table of Contents Hydraulic Motor (810-427C) S/N 458502- Applies to SA30 Section 4: Hydraulic Motor - SA30 (Post Hole Diggers) 19269 12 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Hydraulic Motor (810-427C) S/N 458502- Section 4: Hydraulic Motor - SA30 (Post Hole Diggers) Applies to SA30 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 dwg19269 810-427C 021352 ME016000 ME018000A1 ME015000 477342 ME127003 ME123000 068024 ME019005 071019 400136 069017 ME012001A1 068027 810-431C Drawing Image Number HYD MTR 12 CU IN DSP SA SERIES ROSS BOLT ROSS END COVER ROSS SEAL RING ROSS COMMUTATOR ASSEMBLY ROSS COMMUTATOR SEAL ROSS MANIFOLD ROSS WEAR PLATE ROSS ROTOR SET ROSS DRIVE LINK ROSS THRUST BEARING ROSS COUPLING SHAFT ROSS INNER BEARING ROSS THRUST WASHER ROSS THRUST BEARING ROSS INNER SEAL ROSS BACKUP WASHER ROSS BACKUP WASHER ROSS SERVICE HOUSING ASS'Y ROSS OUTER BEARING ROSS DIRT & WATER SEAL SEAL KIT ROSS ME & MB SK000092 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 13
Table of Contents White Hydraulic Motor (810-530C) S/N 458503+ Applies to SA30 Section 4: Hydraulic Motor - SA30 (Post Hole Diggers) 22409 14 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents White Hydraulic Motor (810-530C) S/N 458503+ Section 4: Hydraulic Motor - SA30 (Post Hole Diggers) Applies to SA30 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. dwg22409 500444001 500018252 500018003 500131823 500018002 500018059 500014009 500015006 500167004 500012001 500018048 500016001 500445012 500011600 500018075 Drawing Image Number WH SEAL KIT DUST SEAL RETAINING RING METAL BACK UP SHIM HOUSING SEAL METAL BACK UP SHIM BACK UP SEAL HIGH PRESSURE SHAFT SEAL REAR HOUSING SEAL BODY SEALS (2) ENDCOVER SEAL SEAL CARRIER THRUST WASHER WH FRONT THRUST BEARING WH FRONT HOUSING BEARING WH "A31" HOUSING WH REAR HOUSING BEARING WH REAR THRUST BEARING WH DRIVE LINK WH FORWARD MANIFOLD WH ROTOR SET WH BALANCE PLATE WH STEEL BALLS (3) WH ENDCOVER WH BOLTS (7) WH SHAFT WH SPACER Includes items 2-13 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 15
Table of Contents Hydraulic Motor (810-424C) S/N 459700- Applies to SA35 Section 4: Hydraulic Motor - SA35 (Skid Steer Mount) 19269 16 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Hydraulic Motor (810-424C) S/N 459700- Section 4: Hydraulic Motor - SA35 (Skid Steer Mount) Applies to SA35 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 dwg19269 810-424C 021340 ME016000 ME018000A1 ME015000 477342 ME187003 ME183000 068024 ME019005 071019 400136 069017 ME012001A1 068027 810-431C Drawing Image Number HYD MTR 18 CU IN DSP SA SERIES ROSS BOLT ROSS END COVER ROSS SEAL RING ROSS COMMUTATOR ASSEMBLY ROSS COMMUTATOR SEAL ROSS MANIFOLD ROSS WEAR PLATE ROSS ROTOR SET ROSS DRIVE LINK ROSS THRUST BEARING ROSS COUPLING SHAFT ROSS INNER BEARING ROSS THRUST WASHER ROSS THRUST BEARING ROSS INNER SEAL ROSS BACKUP WASHER ROSS BACKUP WASHER ROSS SERVICE HOUSING ASS'Y ROSS OUTER BEARING ROSS DIRT & WATER SEAL SEAL KIT ROSS ME & MB SK000092 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 Found in seal kit item #21 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 17
Table of Contents White Hydraulic Motor (810-531C) S/N 459701+ Applies to SA35 Section 4: Hydraulic Motor - SA35 (Skid Steer Mount) 22409 18 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents White Hydraulic Motor (810-531C) S/N 459701+ Section 4: Hydraulic Motor - SA35 (Skid Steer Mount) Applies to SA35 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. 16. 17. 18. 19. 20. 2 2 2 24. 25. 26. 27. dwg22409 500444001 500018252 500018003 500131823 500018002 500018059 500014007 500015006 500247005 500012001 500018048 500016001 500445018 500011600 Drawing Image Number WH SEAL KIT DUST SEAL RETAINING RING METAL BACK UP SHIM HOUSING SEAL METAL BACK UP SHIM BACK UP SEAL HIGH PRESSURE SHAFT SEAL REAR HOUSING SEAL BODY SEALS (2) ENDCOVER SEAL SEAL CARRIER THRUST WASHER WH FRONT THRUST BEARING WH FRONT HOUSING BEARING WH "A31" HOUSING WH REAR HOUSING BEARING WH REAR THRUST BEARING WH DRIVE LINK WH FORWARD MANIFOLD WH ROTOR SET WH BALANCE PLATE WH STEEL BALLS (3) WH ENDCOVER WH BOLTS (7) WH SHAFT WH SPACER Includes items 2-13 810-530C only 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 19
Label Placement Applies to SA30, SA35 Table of Contents Section 5: Labels - SA30/35 (Post Hole Diggers) 19243 20 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Label Placement Section 5: Labels - SA30/35 (Post Hole Diggers) Applies to SA30, SA35 Ref. Part No. Part Description Comments Revision 4. 5. 6. 7. 8. 9. 10. 1 dwg19243 990-211R 848-159C 818-897C 838-290C 848-359C 838-291C 818-190C 838-292C 838-293C 838-294C 838-094C 818-138C 818-862C 135500 Drawing Image Number 3M CONFORM. ANTI-SLIP 2" WIDE DECAL LANDPRIDE 10" BROWN/GOLD DECAL LANDPRIDE 10" - BROWN DECAL SA30 BROWN DECAL, SA35 GOLD DECAL SA35 BROWN DECAL FLAG DECAL ELECTROCUTE HAZARD DECAL WARNING READ MANUAL DECAL DANGER ROTATING AUGER DECAL WARNING HYD PRESS LONG DECAL GREASE EVERY 25 HOURS DECAL 5 YEAR GEARBOX WARRANTY DECAL, DANGER AVOID INJURY S/N 689254- S/N 610954+ S/N 610953- S/N 610954+ S/N 610953-04/01/11 SA30 & SA35 Post Hole Digger 317-093P 21
Auger Applies to SA30, SA35 Table of Contents Section 6: Options & Accessories - SA30/35 (Post Hole Diggers) 26724 22 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents Section 6: Options & Accessories - SA30/35 (Post Hole Diggers) Auger Applies to SA30, SA35 Ref. Part No. Part Description Comments Revision 4. 4. 4. 4. 5. 6. 7. 8. 9. 10. 1 1 1 14. 15. dwg26724 317-096A 317-099A 317-102A 317-105A 317-108A 317-111A 317-114A 317-117A 317-120A 317-123A 317-098A 317-095A 317-101A 317-104A 317-107A 317-110A 317-113A 317-116A 317-119A 317-122A 317-128A 317-129A 317-130A 317-131A 317-132A 317-133A 317-134A 317-135A 802-044C 802-192C 802-214C 802-311C 802-546C 803-019C 803-025C 803-028C 803-147C 820-232C 820-233C Drawing Image Number SA 9X2 9/16 HUB DBL AUG. ASSY SA 12X2 9/16 HUB DBL AUG. ASSY SA 15X2 9/16 HUB DBL AUG. ASSY SA 18X2 9/16 HUB DBL AUG. ASSY SA 24X2 9/16 HUB DBL AUG. ASSY SA 24X2 9/16 HUB TREE AUG ASSY SA 30X2 9/16 HUB DBL AUG ASSY SA 30X2 9/16 HUB TREE AUG ASSY SA 36X2 9/16 HUB DBL AUG. ASSY SA 36X2 9/16 HUB TREE AUG ASSY SA 12X2 HEX HUB DBL AUGER ASSY SA 9X2 HEX HUB DBL AUGER ASSY SA 15X2 HEX HUB DBL AUGER ASSY SA 18X2 HEX HUB DBL AUGER ASSY SA 24X2 HEX HUB DBL AUGER ASSY SA 24X2 HEX HUB TREE AUG ASSY SA 30X2 HEX HUB DBL AUG ASSY SA 30X2 HEX HUB TREE AUG ASSY SA 36X2 HEX HUB DBL AUGER ASSY SA 36X2 HEX HUB TREE AUG ASSY SA 12X2 HEX AUGER EXTEN. ASSY SA 24X2 HEX AUGER EXTEN. ASSY SA 36X2 HEX AUGER EXTEN. ASSY SA 48X2 HEX AUGER EXTEN. ASSY SA 12X2 9/16 OD AUGER EXT. ASY SA 24X2 9/16 OD AUGER EXT. ASY SA 36X2 9/16 OD AUGER EXT. ASY SA 48X2 9/16 OD AUGER EXT. ASY HHCS 1/2-13X4 GR5 HHCS 3/4-10X4 1/2 GR5 RHSNB 1/2-13X1 1/4 GR5 HHCS 1/2-13X4 1/4 GR5 HHCS 7/8-9X5 GR5 NUT LOCK 1/2-13 PLT NUT HEX 3/4-10 PLT NYLOCK NUT NY-LOK 7/8-9 PLT NUT HEX NYLOCK 1/2-13 PENGO TRI-FLOW PILOT BIT PENGO AUGER TOOTH uses 4 teeth uses 4 teeth uses 5 teeth uses 6 teeth uses 8 teeth uses 9 teeth uses 10 teeth uses 11 teeth uses 12 teeth uses 13 teeth uses 4 teeth uses 4 teeth uses 5 teeth uses 6 teeth uses 8 teeth uses 9 teeth uses 10 teeth uses 11 teeth uses 12 teeth uses 13 teeth 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 23
Table of Contents The is a numeric index of all part numbers included in this manual. The index shows what page(s) the part is used on. Part Number Page Part Number Page Part Number Page 010220...11 020280...11 021340...17 021352...13 030447...11 030568...11 040429...11 040436...11 050206...11 050207...11 050208...11 050209...11 060119...11 060120...11 068024...13, 17 068027...13, 17 069017...13, 17 071019...13, 17 090259...11 110187...11 110213...11 120089...11 130058...11 130060...11 130098...11 130120...11 135500...21 140001...11 140062...11 180193...11 317-084H...9 317-085H...9 317-086H...7 317-095A...23 317-096A...23 317-098A...23 317-099A...23 317-101A...23 317-102A...23 317-104A...23 317-105A...23 317-107A...23 317-108A...23 317-110A...23 317-111A...23 317-113A...23 317-114A...23 317-116A...23 317-117A...23 317-119A...23 317-120A...23 317-122A...23 317-123A...23 317-128A...23 317-129A...23 317-130A...23 317-131A...23 317-132A...23 317-133A...23 317-134A...23 317-135A...23 400136...13, 17 477342...13, 17 500011600...15, 19 500012001...15, 19 500014007...19 500014009...15 500015006...15, 19 500016001...15, 19 500018002...15, 19 500018003...15, 19 500018048...15, 19 500018059...15, 19 500018075...15 500018252...15, 19 500131823...15, 19 500167004...15 500247005...19 500444001...15, 19 500445012...15 500445018...19 800-080C...9 802-017C...9 802-044C...23 802-057C...7 802-091C...7 802-192C...23 802-214C...23 802-311C...23 802-546C...23 803-013C...9 803-019C...23 803-021C...7 803-025C...23 803-028C...23 803-147C...23 804-011C...9 804-015C...7 804-022C...7 805-058C...7, 9 805-311C...9 805-312C...7 807-023C...9 810-424C...7, 17 810-427C...7, 13 810-431C...13, 17 810-530C...7 810-531C...7 811-091C...7 811-205C...7 811-744C...7 811-745C...7 811-778C...7 811-779C...7 818-138C...21 818-190C...21 818-862C...21 818-897C...21 820-232C...23 820-233C...23 826-313C...7, 11 826-314C...7, 11 838-094C...21 838-290C...21 838-291C...21 838-292C...21 838-293C...21 838-294C...21 848-159C...21 848-359C...21 990-211R...21 dwg19240...9 dwg19241...7 dwg19242...11 dwg19243...21 dwg19269...13, 17 dwg22409...15, 19 dwg26724...23 ME012001A1...13, 17 ME015000...13, 17 ME016000...13, 17 ME018000A1...13, 17 ME019005...13, 17 ME123000...13 ME127003...13 ME183000...17 ME187003...17...15, 19 24 SA30 & SA35 Post Hole Digger 317-093P 04/01/11
Table of Contents This Page Intentionally Left Blank 04/01/11 SA30 & SA35 Post Hole Digger 317-093P 25
Great Plains Manufacturing, Inc. Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com