FlameWheel550 User Manual V 1.3 www.dji-innovations.com
Disclaimer Read this disclaimer carefully before using FlameWheel550. By using this product, you hereby agree to this disclaimer and signify that you have read them fully. FlameWheel550 is an excellent multi-rotor. With a good autopilot, it will even offer tremendous flight features for low altitude flight working in restricted space. Despite the controller of autopilot operate in the safest manner when the main power battery is connected, we strongly recommend customers to remove all propellers, use power supply from R/C system or flight pack battery, and keep children away during system calibration and parameter setup. Please respect the AMA s National Model Aircraft Safety Code. Dajiang Innovation Technology Co. Ltd. assumes no liability for damage(s) or injuries incurred directly or indirectly from the use of this product. F550 Profile FlameWheel550 (F550) is a multi-rotor designed for all pilots for fun or AP. With DJI WKM or NAZA autopilot system, it can achieve hovering, cruising, even rolling and other flight elements. It can be applied for entertainment, aerial photography, FPV and other aero-modeling activities. 2
Contents Disclaimer... 2 F550 Profile... 2 Contents... 3 Product Usage Cautions... 3 In Box... 4 Tools Needed... 5 Wiring... 5 Assembly... 6 Sound Introduction... 7 Specifications... 7 Product Usage Cautions When flying, the fast rotating propellers of FlameWheel550 will cause serious damage and injury. Therefore, please fly with a high safety consciousness. 1. Keep flying multi-rotor away from objects, such as obstacles, children, human beings, high-voltage lines and so on. 2. Do not get close to or even touch the working motors and propellers, which will cause serious injury. 3. Do not over load the multi-rotor. 4. Check whether the propellers and the motors are installed correctly and firmly before flight. 5. Make sure the rotation direction of each propeller is correct 6. Check whether all parts of multi-rotor are in good condition before flight. Do not fly with old or broken parts. 7. Use DJI parts as much as possible. If you have any problem you cannot solve during installation, please contact our customer service. 3
In Box Top Board 550FBT 1 Bottom Board 550FBB 1 Arms 550FAC 4 550FAW 2 10in Propeller Pairs 550P10 4 Motors 550MOT 6 550 6 + - 30A OPTO U V W Screws 550-M3 8 24 Screws 550-M2.5 5 36 Magic Strap 550MSX 1, Battery Band 550BBX 1, Power Line Pair 550PLP 1 4
Tools Needed 2.0mm Hex Wrench Screw Glue Nylon Cable Tie Scissors Diagonal Cutting Pliers Foam Double Sided Adhesive Tape Soldering-iron & Wires For frame and motors installation. For fastening screws. For binding devices and wires. For fixing receiver, controller and other modules. For connecting s power cables to bottom board. Wiring To Battery Power Pads Please solder s to bottom board as the up figure shows. Use any insulating method at all soldering spots. Make sure there is no short or open circuit. Make sure the side with bonding pads is upward. 5
Assembly Screws M2.5 5 Top Board ② ③ ① ④ Screws M3 8 ⑤ Step 1 Install bottom board Step 2 Install autopilot system Install screws by appropriate force to prevent breaking threads. Use adequate screw glue for installing screws. ⑥ Bottom Board Step 3 Install motors, s Please wire neatly. Make sure wires will not be cut by frame boards and propellers. Smooth out the boards edge if necessary. Step 4 Install top board Step 5 Install propellers Please install propellers after autopilot system configuration procedure. Make sure the rotation direction of propellers are the same as the figure shows. In up figure, arms ①② front of craft, arms ④⑤ are back of craft. See from top, motors on arms ①③⑤ rotate counter-clock wise, use propellers 1045; motors on arms ②④⑥ rotate clock wise, use propellers 1045R. 6
Sound Introduction State Ready Throttle stick is not at bottom Input signal abnormal Sound 1234567 BBBBBB B--------B--------B Input voltage abnormal BB---BB---BB---BB Tips: DJI s are specially designed for multi-rotors. When use with DJI autopilot systems, you do not have to setup any parameters or calibrate travel range. Specifications Frame Diagonal Wheelbase Frame Weight Takeoff Weight 550mm 478g 1200g ~ 2400g Current Signal Frequency Battery Motor Stator size KV Propeller 30A OPTO 30Hz ~ 450Hz 3S ~ 4S LiPo 22 12mm 920rpm/V 10 4.5in (@3S); (Optional 8 4.5in (@4S)) 7
FlameWheel 550 2010-2011 Dajiang Innovation Technology Co. Ltd. All Rights Reserved. 6/F, HKUST SZ IER Building, No.9, Yuexing 1st Rd., South District, Hi-Tech Park, Shenzhen, 518057, Guangdong, China Tel: +86-755-2665-6677 Sales ext: 201, 202, 203 Fax: +86-755-83067370 Service hotline: +86-755-22673777 Sales: sales@dji-innovations.com Technical support: support@dji-innovations.com Others: info@dji-innovations.com DJI FLAME WHEEL is registered trademark of Dajiang Innovation Technology Co. Ltd. Names of product, brand, etc., appearing in this manual are trademarks or registered trademarks of their respective owner companies. This product and manual are copyrighted by Dajiang Innovation Technology Co. Ltd. with all rights reserved. No part of this product or manual shall be reproduced in any form without the prior written consent or authorization of Dajiang Innovation Technology Co. Ltd. No patent liability is assumed with respect to the use of the product or information contained herein. 8