130 CX PET Light Technical Data Injection Moulding Machines Series CX PET Light
CX KM 130-750 CX (PET) 4-fold Injection Moulding machine metric units KM130CX Clamp unit Clamping force kn 1300 Mould opening force kn 70 Travel data of movable platen opening travel force kn 35 closing travel force kn 31 max. opening speed mm/sec 850 max. closing speed mm/sec 830 Platen dimensions (h x v) mm 745 x 770 mm 805 x 770 Clearance between tie bars (h x v) mm 470 x 470 mm 530 x 470 Mould opening stroke mm 600 Minimum mould height mm 300 extended ZE 45.462 mm 500 Maximum daylight mm 900 extended ZE 45.462 mm 1100 Ejector stroke mm 150 extended ZE 50.50 mm 200 Ejector force (forward / backward) ZE 50.60 kn 42,8/30 Injection Unit SP750 Working capacity1) cm³ 743 Screw diameter 4) mm 40 45 50 L/D-ratio (ZE 27.00) 25,2 23 23 Specific injection pressure bar 2500 2336 1892 Stroke volume cm³ 251 318 393 Shot weight (PET) g 270 345 425 Injection rate cm³/sec 113 143 177 Injection rate (PET) g/sec 123 155 193 Screw speed (at 0,42m/s / max. stage 1) Plasticizing rate (PET at 0,42m/s) 2) 1/min 200 / 265 180 / 265 160 / 265 g/sec 21 26 32 Nozzle pressure kn 50 General machine data Nominal capacity of pump motor kw 22 Installed heating capacity Barrel zones including nozzle kw 15,6 5 Dry cycle number3) 1/h 1500 Dry cycle time sec 2,4 Oil capacity liter. 489 Dimensions and Weights Net weight including control cabinet Installation dimensions (l x w x h) Maximum mould weight t 6,2 m 4,9x1,6x2,1 kg 1485 Subject to technical alterations 1) International classification calculated as max. stroke volume (cm3) x max. injection pressure (bar) divided by 1000 2) As per KM standard 3) As per Euromap 6 4) KraussMaffei PET screw *) Approximate values
CX KM 130-750 CX (PET) 6-fold Injection Moulding machine metric units KM130CX Clamp unit Clamping force kn 1300 Mould opening force kn 70 Travel data of movable platen opening travel force kn 35 closing travel force kn 31 max. opening speed mm/sec 850 max. closing speed mm/sec 830 Platen dimensions (h x v) mm 745 x 770 mm 805 x 770 Clearance between tie bars (h x v) mm 470 x 470 mm 530 x 470 Mould opening stroke mm 600 Minimum mould height mm 300 extended ZE 45.462 mm 500 Maximum daylight mm 900 extended ZE 45.462 mm 1100 Ejector stroke mm 150 extended ZE 50.50 mm 200 Ejector force (forward / backward) ZE 50.60 kn 42,8/30 Injection Unit SP750 Working capacity1) cm³ 743 Screw diameter 4) mm 40 45 50 L/D-ratio (ZE 27.00) 25,2 23 23 Specific injection pressure bar 2500 2336 1892 Stroke volume cm³ 251 318 393 Shot weight (PET) g 270 345 425 Injection rate cm³/sec 113 143 177 Injection rate (PET) g/sec 123 155 193 Screw speed (at 0,42m/s / max. stage 1) Plasticizing rate (PET at 0,42m/s) 2) 1/min 200 / 265 180 / 265 160 / 265 g/sec 21 26 32 Nozzle pressure kn 50 General machine data Nominal capacity of pump motor kw 22 Installed heating capacity Barrel zones including nozzle kw 15,6 5 Dry cycle number3) 1/h 1500 Dry cycle time sec 2,4 Oil capacity liter. 489 Dimensions and Weights Net weight including control cabinet Installation dimensions (l x w x h) Maximum mould weight t 6,2 m 4,9x1,6x2,1 kg 1485 Subject to technical alterations 1) International classification calculated as max. stroke volume (cm3) x max. injection pressure (bar) divided by 1000 2) As per KM standard 3) As per Euromap 6 4) KraussMaffei PET screw *) Approximate values
CX KM 130-750 CX (PET) 6-fold Injection Moulding machine metric units KM130CX Clamp unit Clamping force kn 1300 Mould opening force kn 70 Travel data of movable platen opening travel force kn 35 closing travel force kn 31 max. opening speed mm/sec 850 max. closing speed mm/sec 830 Platen dimensions (h x v) mm 745 x 770 mm 805 x 770 Clearance between tie bars (h x v) mm 470 x 470 mm 530 x 470 Mould opening stroke mm 600 Minimum mould height mm 300 extended ZE 45.462 mm 500 Maximum daylight mm 900 extended ZE 45.462 mm 1100 Ejector stroke mm 150 extended ZE 50.50 mm 200 Ejector force (forward / backward) ZE 50.60 kn 42,8/30 Injection Unit SP1000 Working capacity1) cm³ 996 Screw diameter 4) mm 50 55 60 L/D-ratio (ZE 27.00) 23 23 23 Specific injection pressure bar 2304 1904 1600 Stroke volume cm³ 432 523 622 Shot weight (PET) g 460 570 678 Injection rate cm³/sec 157 190 226 Injection rate (PET) g/sec 170 205 245 Screw speed (at 0,42m/s / max. stage 1) Plasticizing rate (PET at 0,42m/s) 2) 1/min 160/ 195 145 / 195 135 / 195 g/sec 32 40 45 Nozzle pressure kn 82 General machine data Nominal capacity of pump motor kw 30 Installed heating capacity Barrel zones including nozzle kw 19,2 5 Dry cycle number3) 1/h 1500 Dry cycle time sec 2,4 Oil capacity liter. 489 Dimensions and Weights Net weight including control cabinet Installation dimensions (l x w x h) Maximum mould weight t 7,8 m 5,3x1,6x2,1 kg 1485 Subject to technical alterations 1) International classification calculated as max. stroke volume (cm3) x max. injection pressure (bar) divided by 1000 2) As per KM standard 3) As per Euromap 6 4) KraussMaffei PET screw *) Approximate values
CX KM 130-750 CX (PET) 8-fold Injection Moulding machine metric units KM130CX Clamp unit Clamping force kn 1300 Mould opening force kn 70 Travel data of movable platen opening travel force kn 35 closing travel force kn 31 max. opening speed mm/sec 850 max. closing speed mm/sec 830 Platen dimensions (h x v) mm 745 x 770 mm 805 x 770 Clearance between tie bars (h x v) mm 470 x 470 mm 530 x 470 Mould opening stroke mm 600 Minimum mould height mm 300 extended ZE 45.462 mm 500 Maximum daylight mm 900 extended ZE 45.462 mm 1100 Ejector stroke mm 150 extended ZE 50.50 mm 200 Ejector force (forward / backward) ZE 50.60 kn 42,8/30 Injection Unit SP1400 Working capacity1) cm³ 1362 Screw diameter 4) mm 55 60 70 L/D-ratio (ZE 27.00) 23 23 23 Specific injection pressure bar 2387 2006 1473 Stroke volume cm³ 570 679 924 Shot weight (PET) g 630 750 1010 Injection rate cm³/sec 238 283 385 Injection rate (PET) g/sec 260 310 420 Screw speed (at 0,42m/s / max. stage 1) Plasticizing rate (PET at 0,42m/s) 2) 1/min 145 / 230 135 / 230 115 / 230 g/sec 40 45 60 Nozzle pressure kn 82 General machine data Nominal capacity of pump motor kw 37 Installed heating capacity Barrel zones including nozzle kw 22,7 6 Dry cycle number3) 1/h 1500 Dry cycle time sec 2,4 Oil capacity liter. 489 Dimensions and Weights Net weight including control cabinet Installation dimensions (l x w x h) Maximum mould weight t 8 m 6,2x1,8x2,4 kg 1485 Subject to technical alterations 1) International classification calculated as max. stroke volume (cm3) x max. injection pressure (bar) divided by 1000 2) As per KM standard 3) As per Euromap 6 4) KraussMaffei PET screw *) Approximate values
CX KM 130-1400 CX (PET) 12-fold Injection Moulding machine metric units KM130CX Clamp unit Clamping force kn 1300 Mould opening force kn 70 Travel data of movable platen opening travel force kn 35 closing travel force kn 31 max. opening speed mm/sec 850 max. closing speed mm/sec 830 Platen dimensions (h x v) mm 745 x 770 mm 805 x 770 Clearance between tie bars (h x v) mm 470 x 470 mm 530 x 470 Mould opening stroke mm 600 Minimum mould height mm 300 extended ZE 45.462 mm 500 Maximum daylight mm 900 extended ZE 45.462 mm 1100 Ejector stroke mm 150 extended ZE 50.50 mm 200 Ejector force (forward / backward) Special kn 59,7/42 Injection Unit SP1400 Working capacity1) cm³ 1362 Screw diameter 4) mm 55 60 70 L/D-ratio (ZE 27.00) 23 23 23 Specific injection pressure bar 2387 2006 1473 Stroke volume cm³ 570 679 924 Shot weight (PET) g 630 750 1010 Injection rate cm³/sec 238 283 385 Injection rate (PET) g/sec 260 310 420 Screw speed (at 0,42m/s / max. stage 1) Plasticizing rate (PET at 0,42m/s) 2) 1/min 145 / 230 135 / 230 115 / 230 g/sec 40 45 60 Nozzle pressure kn 82 General machine data Nominal capacity of pump motor kw 37 Installed heating capacity Barrel zones including nozzle kw 22,7 6 Dry cycle number3) 1/h 1500 Dry cycle time sec 2,4 Oil capacity liter. 489 Dimensions and Weights Net weight including control cabinet Installation dimensions (l x w x h) Maximum mould weight t 8 m 6,2x1,8x2,4 kg 1485 Subject to technical alterations 1) International classification calculated as max. stroke volume (cm3) x max. injection pressure (bar) divided by 1000 2) As per KM standard 3) As per Euromap 6 4) KraussMaffei PET screw *) Approximate values
KM 130 CX PET Light - SP750/SP1000
KM 130 CX PET Light - Sp1400
KM 130 CX PET Light
KraussMaffei is a premium partner for the plastics and rubber processing industries worldwide. KraussMaffei machines and systems are used wherever plastics and rubber are converted into products. As a knowledge-driven technology company, we build on many decades of experience and a strong commitment to research and development. The CX series from KraussMaffei is a range of small and medium tonnage, all-hydraulic injection moulding machines. Their dominant feature is the two-platen clamp that produces a compact machine with very good all-round access. CX machines with KraussMaffei s efficient hydraulics deliver highest precision and performance over very long service lives. The PET light edition ensures you start at the right base when it comes to preform moulding. Special designed PET screws and the KraussMaffei preform performance ZE-package enable an optimum processing of PET thus the efficient production of preforms for small lots from 4 to 12 cavities. 1.0 JF 1st edition 12/09 SGM 801 A DAT 12/2009 GB KraussMaffei Technologies GmbH Krauss-Maffei-Strasse 2 80997 Munich Phone +49 89 8899-0 Fax +49 89 8899-2206 www.kraussmaffei.com