ToppTube PA11 (Polyamide) page 4 ToppTube PA12 (Polyamide) page 5 ToppTube PA12HIPHL (Polyamide) page 6 ToppTube PUR 98A (Polyurethane) page 7 ToppTube PE-LD (Polyethylene) page 8 ToppTube PE-LLD (Polyethylene) page 9 ToppTube PE-HD (Polyethylene) page 10 ToppTube PEX (Polyethylene) page 11 ToppSpiral Spiral Tubes page 12 ToppPart Pre-Bent Tubes page 13 ToppMulti Multi-Cables page 14
Flexible pressure-resistant tubes for pneumatic and hydraulic applications, as well as for grease lubrication. Superior in high temperature applications. Good impact resistance Excellent abrasion resistance PA11 hard quality PA11P40 semi-hard quality PA11F15 soft quality Technical information Material Hardness Polyamide PA11 (Nylon 11) Rilsan PA11: 70 Shore D, PA11P40: 63 Shore D, PA11F15: 52 Shore D Installation Temperature -20 C...+50 C Working Temperature -40 C...+80 C Operating Pressure 4,0 bar...135 bar (depending on tube dimensions and temperature). Tolerances According to DIN 74324. Colours Natural, black, blue, yellow, red, green, silver, etc. Outer diameter 3,0 mm...28,0 mm x inner diameter 2,0 mm...24,0 mm. Chemical Resistance PA tubes have good chemical resistance against oils, hydraulic fluids, and fuels. Not suitable for chloride compounds. Value Unit Test Method Density 1,05 g/cm³ ISO 1183 mm Working pressure (bar), safety factor 3 PA11 PA11P40 PA11F15 Temperature C Temperature C Temperature C Weight Bending radius O.D./I.D. 23 C 40 C 60 C 80 C 23 C 40 C 60 C 80 C 23 C 40 C 60 C g/m min. mm 4/2 75 53 41 32 44 32 25 21 29 21 17 9,9 24 5/3 56 39 30 24 33 24 19 16 21 15 12 13,2 30 6/4 45 32 24 19 26 19 15 12 17 12 10 16,5 36 8/6 32 22 17 14 19 14 11 9 12 9 7 23,1 50 10/8 25 18 14 11 14 10 8 7 9 6 5 29,7 80 12/10 20 14 11 14 12 9 7 6 7 5 4 36,3 118 14/12 17 12 9 7 10 7 6 5 6 4 3 42,9 163 15/12,5 20 14 11 9 12 9 7 6 7 5 4 56,7 90 16/12 32 22 17 14 19 14 11 9 12 9 7 92,4 100 18/15 20 14 11 9 12 9 7 6 7 5 4 81,6 177 22/18 22 15 12 9 13 9 7 6 8 6 5 131,9 196 Besides standard dimensions we can also manufacture special dimensions. 4 The company reserves the right to make changes without notice.
Good impact resistance Superior in high temperature applications High pressure resistance Applications Pneumatics Industrial robots Instrumentation lines Technical information Material Polyamide PA12 (Nylon 12) Hardness PA12: Special product, PA12P40: 60 shore D Installation Temperature -20 C...+50 C Working Temperature -40 C...+80 C Operating Pressure 4,0 bar...135 bar (depending on tube dimensions and temperature). Tolerances According to DIN 74324. Colours Natural, black, blue, yellow, red, green, silver, etc. Chemical Resistance mm Outer diameter 3,0 mm...28,0 mm x inner diameter 2,0 mm...24,0 mm. PA tubes have good chemical resistance against oils, hydraulic fluids, and fuels. Not suitable for chloride compounds. Value Unit Test Method Density 1,03 g/cm³ ISO 1183 PA12 Working pressure (bar), safety factor 3 PA12P40 Temperature C Temperature C Weight Bending radius O.D./I.D. 23 C 40 C 60 C 80 C 23 C 40 C 60 C 80 C g/m min. mm 4/2 75 53 41 32 44 32 25 21 9,9 24 5/3 56 39 30 24 33 24 19 16 13,2 30 6/4 45 32 24 19 26 19 15 12 16,5 36 8/6 32 22 17 14 19 14 11 9 23,1 50 10/8 25 18 14 11 14 10 8 7 29,7 80 12/10 20 14 11 9 12 9 7 6 36,3 118 14/12 17 12 9 7 10 7 6 5 42,9 163 15/12,5 20 14 11 9 12 9 7 6 56,7 90 16/12 32 22 17 14 19 14 11 9 92,4 100 18/15 20 14 11 9 12 9 7 6 81,6 177 22/18 22 15 12 9 13 9 7 6 131,9 196 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 5
We manufacture the brake tubes strictly according to the DIN 74324 quality standard which requires a black colour. Vehicle tubes are manufactured according to the DIN 73378 quality standard, which offers many colour alternatives. Applications: Flexible brake tube for automotive applications For demanding installations Automotive Technical information Material PA12HIPHL-DIN Hardness 63 Shore D ISO 868 Installation Temperature -20 C...+93 C Working Temperature -40 C...+93 C Operating Pressure 4,0 bar...135 bar (depending on tube dimensions and temperature). Tolerances According to DIN 74324. Colours Black in DIN 74324. Red, blue, yellow in DIN 73378. Outer diameter 4,0 mm...18 mm x inner diameter 2,0 mm...14,0 mm Chemical Resistance Excellent chemical resistance against oils, hydraulic fluids and fuels. Not suitable for chloride compounds. Value Unit Test Method Density 1,03 g/cm³ ISO 1183 Working pressure (bar), safety factor 3 mm Temperature C Weight Bending radius O.D./I.D. 23 C 40 C 60 C 80 C g/m min. mm 4/2 44 32 25 21 9,9 24 6/4 26 19 15 12 16,5 36 6,4/4,3 26 19 15 12 18,5 38 8/6 19 14 11 9 23,1 50 9/6 26 19 15 12 37,1 54 9,5/6,4 26 19 15 12 40,6 57 10/7 23 17 13 11 42,1 60 10/8 14 10 8 7 29,7 80 11/8 21 15 12 10 47,0 66 12/9 19 14 11 9 52,0 75 12,7/9,5 19 14 11 9 58,6 79 14/10 22 16 13 10 79,2 84 15,8/11,2 22 16 13 10 102,4 95 16/12 19 14 11 9 92,4 100 18/14 16 12 9 8 106 129 Besides standard dimensions we can also manufacture special dimensions. 6 The company reserves the right to make changes without notice.
Good flexible properties, performes especially well in low temperatures Wide operating temperature range Excellent abrasion resistance No plasticizers used Excellent elasticity - small bending radius Applications: Pneumatics Industrial robots Instrumentation lines Technical information Material Hardness Polyurethane C98A 98 Shore A Installation Temperature -30 C...+50 C Working Temperature -40 C...+80 C, momentarily 100 C Operating Pressure 2,0 bar...19 bar (depending on tube dimensions and temperature). Tolerances According to DIN 74324. Colours Silver, black, blue (yellow, red, green, natural) etc. Outer diameter 3,0 mm...16 mm x inner diameter 2,0 mm...13,0 mm Chemical Resistance Excellent chemical resistance against oils, hydraulic fluids and fuels. Value Unit Test Method Density 1,22 g/cm³ ISO 1183-1-A Working pressure (bar), safety factor 3 mm Temperature C Weight Bending radius O.D./I.D. 20 C 30 C 40 C 50 C 60 C 70 C g/m min. mm 4/2 19 17 15 13 11 10 1,1 9 4,3/2,8 12 11 9 8 7 6 1,0 15 5,3 14 13 11 10 9 8 1,5 14 5/3,1 13 12 10 9 8 7 1,5 15 6/3,9 12 11 9 8 7 7 2,0 20 6/4 11 10 9 8 7 6 1,9 21 8/5,7 10 9 7 7 6 5 3,0 34 8/6 8 7 6 6 5 4 2,7 40 9,5/6,4 11 10 9 8 7 6 4,7 35 10/7 10 9 8 7 6 5 4,9 40 10/8 6 6 5 4 4 3 03,4 64 12/9 8 7 6 6 5 4 6,0 60 14/11 7 6 5 5 4 4 7,2 83 15/12,5 5 5 4 4 3 3 6,6 118 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 7
Low density polyethylene Economical price Reasonable heat and pressure resistance Suitable for recycling using modern methods of shredding and cleaning Good chemical resistance Applications PE-LD tubing is often used in pneumatic equipment due to its easy installation. Technical information Material PE-LD Installation Temperature -30 C...+50 C Working Temperature -40 C...+60 C Operating Pressure 1,0 Bar...22 Bar (depending on tube dimensions and temperature). Tolerances According to DIN 74324. Colours Natural, black, blue, (yellow, red, green, silver, etc.) Outer diameter 4,0 mm...22 mm x inner diameter 2,0 mm...18,0 mm Chemical Resistance Good chemical resistance against gases and liquids. Value Unit Test Method Density 0,922 g/cm³ ISO 1183 Working pressure (bar), safety factor 2,5 mm Temperature C Weight Bending radius O.D./I.D. 20 C 30 C 40 C 50 C 60 C g/m min. mm 4/2 20 13 10 7 5 9,9 24 5/3 15 10 8 5 4 13,2 30 6/4 12 8 6 4 3 16,5 36 8/6 8 5 4 3 2 23,1 50 10/8 6 4 3 2 2 29,7 80 12/9 8 5 4 3 2 52,0 75 14/12 4 3 2 1 1 42,9 163 15/12,5 5 3 3 2 1 56,7 147 16/12 8 5 4 3 2 92,4 100 20/16 6 4 3 2 2 118,8 161 22/18 6 4 3 2 2 131,9 196 Besides standard dimensions we can also manufacture special dimensions. 8 The company reserves the right to make changes without notice.
Linear low density polyethylene Good chemical resistance Economical price Applications: Pneumatic installations Installations where gas and chemical contact is required. Technical information Material PE-LLD Installation Temperature -30 C...+50 C Working Temperature -40 C...+60 C Operating Pressure Depending on tube dimensions and temperature. Tolerances According to DIN 74324. Colours Blue, natural, black. Other colours by request. Outer diameter 4,0 mm...22 mm x inner diameter 2,0 mm...18,0 mm Chemical Resistance Good chemical resistance against gases and liquids. Value Unit Test Method Density 0,931 g/cm³ ISO 1183 Working pressure (bar), safety factor x mm Temperature C Weight Bending radius O.D./I.D. 20 C 40 C 60 C g/m min. mm 4/2 32 22 15 8,8 24 5/3 24 17 11 11,7 30 6/4 19 13 9 14,6 36 8/6 14 10 6 20,5 50 10/8 10 7 5 26,3 80 12/9 14 10 6 46,1 75 14/12 7 5 3 38,0 163 15/12,5 8 6 4 50,3 147 16/12 14 10 6 81,9 100 20/16 10 7 5 105,3 161 22/18 9 6 4 117,0 196 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 9
Low cost tube with superior chemical resistance High impact strenght for more demanding applications Technical information Material PE-HD High-density polyethylene Hardness 65 Shore D ISO 868 Installation Temperature -30 C...+50 C Working Temperature -30 C...+60 C Operating Pressure Depending on tube dimensions and temperature. Tolerances According to DIN 74324. Colours Colours by request. On request. Chemical Resistance Good chemical resistance against gases and liquids. Value Unit Test Method Density 0,958 g/cm³ ISO 1183 10 The company reserves the right to make changes without notice.
A high density cross linked polyethylene Good processabilty High density Flexible Excellent chemical resistance Excellent heath resistance Excellent impact resistance Applications: Piping Plumbing parts Portable water applications Technical information Material Cross-linked polyethylene PEX Installation Temperature -30 C...+60 C Working Temperature -40 C...+80 C Operating Pressure 1,0 bar 33 bar (depending on tube dimensions and temperature) Tolerances According to DIN 74324. Colours Black, blue, natural Outer diameter 4,0 mm...22 mm x inner diameter 2,0 mm...18,0 mm Chemical Resistance Excellent chemical resistance in lower pressures and temperatures, especially against gases and liquids. Value Unit Test Method Density 0,942 g/cm³ ASTM D792 The company reserves the right to make changes without notice. 11
Handy accessibility with a tailored spiral tube! ToppSpiral PA is a premium quality spiral tube. Its flexibility provides handy accessibility in pneumatic systems. The tube is made of durable polyamid which maintains its shape. For vertical installations we recommend a semi-rigid quality, and for horizontal installations a rigid quality. We manufacture ToppSpiral PA spiral tubes to order. In the table you can find several samples. If you can t find the spiral you need, please call us and let us know the dimensions and the outer and inner diameter of the requested spiral. I.D. B A O.D. Recommendation Ordering Colours Sizes Tube dimensions mm. For horizontal fitting medium hard polyamide, for vertical fitting hard polyamide. The spirals are manufactured by request. Standard colour is blue, other colours by request. Other sizes or with straight heads by request. Spiral dimensions mm. O.D. I.D. Work length B Ø Free length A 4,0 2,0 5000 22 367 6,0 4,0 5000 60 217 8,0 6,0 5000 60 281 8,0 6,0 5000 100 177 10,0 8,0 5000 100 217 10,0 8,0 5000 127 174 12,0 10,0 5000 127 206 15,0 12,5 5000 150 217 15,0 12,5 5000 215 156 16,0 12,0 5000 215 165 25,0 19,0 5000 320 173 4,0 2,0 1000 22 735 6,0 4,0 1000 60 434 6,0 4,0 1000 100 270 8,0 6,0 1000 100 354 10,0 8,0 1000 100 434 10,0 8,0 1000 127 349 12,0 10,0 1000 127 412 15,0 12,5 1000 150 434 15,0 12,5 1000 215 311 16,0 12,0 1000 215 331 25,0 19,0 1000 320 346 4,0 2,0 1500 22 1102 6,0 4,0 1500 60 651 6,0 4,0 1500 100 405 8,0 6,0 1500 100 531 10,0 8,0 1500 100 651 10,0 8,0 1500 127 532 12,0 10,0 1500 127 618 15,0 12,5 1500 150 651 15,0 12,5 1500 215 467 16,0 12,0 1500 215 496 25,0 19,0 1500 320 519 6,0 4,0 2000 60 868 6,0 4,0 2000 100 541 8,0 6,0 2000 100 707 10,0 8,0 2000 100 868 10,0 8,0 2000 127 697 12,0 10,0 2000 127 824 15,0 12,5 2000 150 868 15,0 12,5 2000 215 623 16,0 12,0 2000 215 661 25,0 19,0 2000 320 692 Besides standard dimensions we can also manufacture special dimensions. 12 The company reserves the right to make changes without notice.
Faster and easier installations with ToppPart tubes! The pre-bent ToppPart tubes are designed for instant installations in pneumatic and liquid applications. Hence, the installation of ToppPart tubes is very fast and easy. And less time in installations means savings. ToppPart tubes are an alternative in applications in which it is not possible to use metal tubing. ToppPart tubes are tailored according to customer s specific needs. We can manufacture both 2D and 3D shapes using our unique state of the art CNC bending technology. What material we can bend? We currently have the capability to bend PA11, PA12 and PEX tubes with an outer diameter between 6 mm and 30 mm, into an almost limitless variations of bends to fit any application. Want to know more? For more information please contact our customer service: customerservice@toppi.fi. A, B and C refers to the length between bends, these can be between 120 mm- 2000 mm. We will be happy to consider the dimensions on request. The company reserves the right to make changes without notice. 13
One product - multiple solutions A ToppMulti cable is a selection of e.g. pneumatic tubes, fluid tubes, electrical cables and optical fibres combined into one cable. We manufacture the ToppMulti cables according to our customers specific needs. Notes Not a stock item. Minimum order quantity 500 meters. General Information and Quality Certificate Extruded PE- (Polyethylene) PA- (Polyamide) or PUR- (Polyurethane) tubes in variable combinations covered General with a PVC jacket. Other materials in tubing and jacket on request. Continuous measurement of tube outer diameter from two directions, wall thickness at six points. Quality control Regular control of the tubes burst pressure. Tolerance of tubes Complying DIN 74324. Number of tubes 1-19 pcs., the maximum number of tubes depends on the individual tube sizes. Electrical cables Optional for supplying of electrical signals, usually supplied by customer. PVC-jacket PVC (polyvinyl chloride), black, blue or grey. Other materials on request. Bending radius Minimum seven (7) times the maximum measure of the jacket. Lenghts Standard length is 500 m, delivered on drum. Protective foil Polyester, standard thickness 12 µm. O-3 PE - 6/4 BLACK L-3 PE - 6/4 BLACK Example LAL-3 PE - 6/4 BLACK OAL-3 PE - 6/4 BLACK O More or less round jacket, maximum 3 pcs. filler profiles used. L Jacket only. LAL Jacket with aluminium (12 µm) and polyester foil (12 µm), and without filler profiles. OAL Jacket with aluminium (12 µm) and polyester foil (12 µm), and filler profiles. Explanation 3 Number of tubes, numbering clockwise begining from center. PE Polyethylene tubing used. 6/4 Tube size, the tubes can have different colors (max. 6) or numbering. BLACK The color of jacket, other colours on request. 14 The company reserves the right to make changes without notice.
TUBES JACKET Cross section Article pcs. Raw Material Color Raw Material L-1PE-6/4 BLACK 1 PE (alternative PA or PUR) BLACK PVC (other materials on request) L-2PE-6/4 BLACK 2 PE (alternative PA or PUR) BLACK PVC (other materials on request) L-3PE-6/4 BLACK 3 PE (alternative PA or PUR) BLACK PVC (other materials on request) O-2PE-6/4 BLACK 2 PE (alternative PA or PUR) BLACK PVC (other materials on request) O-3PE-6/4 BLACK 3 PE (alternative PA or PUR) BLACK PVC (other materials on request) O-7PE-6/4 BLACK 7 PE (alternative PA or PUR) BLACK PVC (other materials on request) JACKET MEASURES Article ~ Weight kg/m ~ Outer mm L-1PE-6/4 0,060 Ø 9,4 L-1PE-8/6 0,075 Ø 11,4 L-1PE-10/8 0,091 Ø 13,4 L-2PE-6/4 0,089 15,4 x 9,4 L-2PE-8/4 0,115 19,4 x 11,4 L-2PE-10/8 0,140 23,4 x 13,4 L-3PA-6/4 0,104 15,4 x 14,6 L-3PE-6/4 0,104 15,4 x 14,6 O-2PE-6,4/4,3 0,119 Ø 16,2 O-2PE-6/4 0,113 Ø 15,4 Besides standard dimensions we can also manufacture special dimensions. The company reserves the right to make changes without notice. 15
Oy Toppi Ab Tiilismäki 9 02330 Espoo Finland Telephone +358 207 589 820 asiakaspalvelu@toppi.fi customerservice@toppi.fi www.toppi.fi