SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3. OPERATING RANGE: SG Pumps (Cast Iron Mag Drive) and SGN (Ductile Iron Mag Drive) Displacements No. 23 SG and 7 SGN 0.06 to 90 (SG) and GPM 0.7 to 32 (SGN) Flow Range 0.03 to 43 (SG) and M 3 /Hr 0.6 to 7.2 (SGN) Pressure Range Temperature Range Viscosity Range PSI to 500 Continuous Bar to 34 Continuous F -40 to 500 C -40 to 260 SSU 2 to 250,000 cst to 55,000 Where shaft seal leakage is not allowable, for liquids that are hard to seal, or where seal maintenance is difficult, Viking Mag Drive sealless SG pumps are the solution. In this type of pump, a canister hermetically seals the liquid within the pump. Inner magnets are connected to the pump drive shaft inside the canister, and an outer magnet assembly rotates outside of the canister, driven by a motor or other drive, so that magnetic forces pass through the canister to the inner magnets and cause the drive shaft to rotate. This eliminates traditional dynamic shaft seals, and problems associated with them (wear, leakage, air infiltration). A hollow drive shaft allows some liquid to flow by means of pressure differential from the high pressure side of the pump through the shaft, into the canister and back to the low pressure side of the pump. This provides magnet cooling and prevents product stagnation. TYPICAL APPLICATIONS: Fuels and Additives Polyurethane Meter / Mix Adhesive & Sealant Dispensing Pipeline Sampling Chemical Metering Heat Transfer Oils VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
Section 34.3 Page 34.3.2 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) MATERIALS OF CONSTRUCTION - ALL SERIES Component Standard - SG-04, -05, -07 Standard - SGN-05, -07 Standard - SG-0, -4 Options Casing, Bracket, Head, Separation Plate Relief Valve Body Cast Iron ASTM A23 Cast Iron ASTM A23 Ductile Iron ASTM A536 Ductile Iron ASTM A536 Relief Valve Poppet Hardened Steel Hardened Steel Relief Valve Spring Steel ASTM A229 Steel ASTM A229 Cast Iron ASTM A23 Cast Iron ASTM A4 Ductile Iron ASTM A536 Chrome Silicon Spring Steel ASTM A40 Gears Hardened Steel Hardened Steel Hardened Steel Shafts Case-Hardened Steel ASTM A322 Case-Hardened Steel ASTM A322 Case-Hardened Steel ASTM A322 Surface Hardening (Vitek) PPS (composite) SG-07 only Nitralloy Anti-Friction Needle Bearings Bearing Steel Sleeve Bearings Carbon Graphite Carbon Graphite Carbon Graphite Silicon Carbide O-Rings Buna-N Buna-N Buna-N Neoprene, Viton, PTFE, Kalrez Canister 36L Stainless Steel 36L Stainless Steel 36L Stainless Steel Alloy C Magnetic Coupling Bracket (not wetted) Cast Iron ASTM A23 Cast Iron ASTM A23 Cast Iron ASTM A23 Aluminum SG-04,-05,-07 only Magnets (outer magnets nickel plated, inner magnets sealed in SS canister) Neodymium Iron Boron Neodymium Iron Boron Neodymium Iron Boron 2 Samarium Cobalt Maximum temperature 225 F / 07 C. 2 Maximum temperature 500 F / 260 C. MODEL NUMBER KEY SGN - 05 - M 0 V Spur Gear Principle Frame Size Pump Size Design Series Material of Construction: Blank = Cast Iron N = Ductile Iron (-05,-07) Seal Type: = Mag Drive NOTE: Direction of rotation: clockwise is standard, counter-clockwise is optional. Bi-rotational is not available as Mag Drive. NOTE: Mag Drive pumps are connected to a magnetic coupling, which is specified separately. Coupling options are MD-A and MD-B (SG-04,-05,-07), MD2-B (SG-0) or MD2-C (SG-4). Specify NEMA or IEC face mount for close-coupled or bearing carrier for long-coupled. See page 34.3.4 to determine the correct coupling. Shaft Rotation: (Viewed from shaft end) 0 = Clockwise = Counter- Clockwise (optional) Relief Valve: O = Without Valve V = With Valve Viton and Kalrez are registered trademarks of DuPont Performance Elastomers VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3.3 SPECIFICATIONS SERIES SG-04, SG-05, SG-07, SG-0, SG-4 (CAST IRON) - SGN-05, SGN-07 (DUCTILE IRON) Model Numbers Port Size 60 Hz Motor Speed Nominal Pump Rating 50 Hz Motor Speed Maximum Continuous Pressure 2 Magnetic Coupling Availability Torque Maximum Hydrostatic Pressure Approximate Shipping Weight Pump With Valve (Less Power) Approximate Coupling Only Shipping Weight (ready to accept but less power) Cast Iron Ductile Iron Inches GPM RPM M 3 /Hr RPM PSI Bar Series Ft-Lbs Nm PSIG Bar Lbs KG Lbs KG SG-047 3 0.06 750 0.0 450 500 34 SG-04 3 0.4 750 0.026 450 500 34 4 5.4 6 2.7 SG-0425 3 0. 750 0.034 450 500 34 MD-A 000 69 SG-0435 3 0.27 750 0.05 450 500 34 3 4 SG-0450 3 0.36 750 0.06 450 500 34 9 2.2 SG-0470 3 0.50 750 0.094 450 500 34 7 3.2 SG-05 SGN-05 3 0.70 750 0.3 450 500 34 SG-0525 SGN-0525 3 750 0.9 450 500 34 6 2.7 SG-0535 SGN-0535 3.4 750 0.26 450 500 34 SG-0550 SGN-0550 3 2 750 0.3 450 500 34 4 5.4 7 3.2 SG-0570 SGN-0570 3 2. 750 0.53 450 500 34 MD-A 000 69 3 4 SG-050 SGN-050 3 4 750 0.75 450 500 34 9 2.2 3.6 SG-054 SGN-054 ¾ 3 5.6 750.05 450 500 34 9 4. SG-059 SGN-059 ¾ 3 7.6 750.43 450 200 4 0 4.5 SG-052 SGN-052 ¾ 3.2 750 2. 450 00 7 5.0 SG-074 SGN-074 3 4 750 0.75 450 500 34 5 6. SG 075 SGN 075 3 5.6 750.05 450 500 34 7 7.7 4 5.4 3 4 SG-072 SGN-072 3 750.5 450 500 34 000 69 MD-A.2 9 2.2 SG-07 SGN-07 3.2 750 2. 450 500 34 9.6 SG-076 SGN-076 3 6 750 3.0 450 500 34 MD-B 5 20.3 400 2 20 9. SG-0722 SGN-0722 x ¼ 3 22 750 4.4 450 500 34 40 54.0 4.6 7 32 SG-0732 SGN-0732 x ¼ 3 32 750 6.02 450 500 34 43 9.5 SG-009 4 6 750 3.0 450 500 34 4 9 45 20.5 SG-03 4 25 750 4.70 450 500 34 MD2-B 32 43 700 4 49 22. SG-026 2 4 50 750 9.4 450 500 34 50 67 54 24.5 SG-420 2 4 70 750 3.7 450 500 34 40 54 30 59. SG-436 3 4 25 750 23.52 450 290 20 MD2-C 90 22 35 3 350 24 5 7.5 SG-456 4 4 90 750 35.75 450 90 3 0 244 9 5. NOTE: Maximum temperature (standard construction) 225 F, 07 C. Higher temperatures can be handled with Samarium Cobalt magnets and optional O-ring elastomers. See page 34.3.4 for torque and temperature limits. Optional high pressure canisters available. Consult factory. 2 See page 34.3.4 for Selecting the correct Mag Drive coupling. 3 NPT standard. Consult factory for other port size or type options such as BSP, SAE O-Ring or other. 4 SAE J5 Code 6 flange with metric threaded fastener holes standard. Consult factory for other port sizes or type options such as NPT, BSP, SAE O-Ring or other. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200 Metric conversions are based on US measurements.
Section 34.3 Page 34.3.4 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) SELECTING THE CORRECT VIKING MAG DRIVE COUPLING With any mag drive pump, the magnetic forces between the inner and outer magnets must meet or exceed the torque generated by the drive at the application s peak flow, speed and pressure, or the magnets will decouple, which can cause permanent loss of magnetic attraction. Instead of offering mag drive pumps with just one torque rating, Viking allows you to select between several magnetic couplings with different torque ratings. This ensures enough torque for the application, but keeps costs down by using only as much torque as is needed. Viking also offers two magnet materials in each of the coupling sizes. The standard Neodymium magnets are lowest cost, but are limited in temperature to 225 F (07 C). The optional Samarium Cobalt magnets range up to 500 F (260 C). Specify magnet material when ordering. Selecting the Right Coupling. Find pump HP and speed from performance curves using the Pump Selector program on www.vikingpump.com 2. Calculate application torque (T), using this formula: T (FT LB) = HP/SPEED x 5252 3. Select temperature correction factor (TCF) from Table or Table 2. 4. Divide the calculated application torque (T) by the temperature correction factor (TCF) to get the Adjusted Application Torque. 5. Select the coupling with a torque rating (from Table 3) equal to or greater than the Adjusted Application Torque (AAT). Viking couplings have a built-in service factor, so if you have calculated the AAT correctly, you can be comfortable with a coupling that is equal to your calculated torque. Application Temp. ( F) Application Temp. ( C) Temperature Correction Factors for Standard Neodymium Magnets 6 00 25 50 75 200 225 20 3 52 66 79 93 07 TC Factor.0 0.94 0. 0.2 0.76 0.70 0.64 Application Temp. ( F) Application Temp. ( C) Temperature Correction Factors for Optional Samarium Cobalt Magnets 75 200 300 400 500 79 93 749 204 260 TC Factor 0.74 0.73 0.69 0.63 0.59 TABLE 2 Magnetic Coupling Torque Capacity Coupling Size Torque (FT-LBS) Nm MD-A4 4 5.4 MD-A9 9 2.2 MD-B5 5 20.3 MD-B40 40 54.2 MD2-B4 4 9.0 MD2-B32 32 43.4 MD2-B50 50 67. MD2-C40 40 54.2 MD2-C90 90 22.0 MD2-C35 35 3.0 MD2-C0 0 244.0 TABLE 3 Example :. An application calls for pumping GPM of 00 SSU (22 cst) liquid at 400 PSI (27 Bar), at 00 F (3 C), with a 750 RPM motor. From the Pump Selector program, an SG0525 is selected, providing 0.95 GPM (3.6 lpm) at 750 RPM, with 0.35 BHP (0.26 kw). 2. Calculate torque. T = 0.35 / 750 x 5252 =.05 3. From Table, the TCF is 0.94. 4. AAT =.05 / 0.94 =.2 FT-LB. 5. Select MD-A4 coupling in standard Neodymium magnet material (4 FT-LB rating >.2 FT-LB Adjusted Application Torque) TABLE VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3.5 DRIVE OPTIONS FOOT-BRACKET MOUNTED PUMPS ( B DRIVE) Series SG- pumps are available with a bearing carrier mounted to the magnetic coupling to provide an external drive shaft for long-coupling to a reducer, gear motor or other drive. The 3.5 shaft height on MD-A couplings matches the shaft height on Viking A series reducers, as well as NEMA 56, 43 and 45 T motors. The 6.25 shaft height on MD-B couplings matches shaft height on 254/256 T motors. The MD2-B coupling for SG-0 has 5.5 shaft height matching Viking B reducers. Dimensions for Foot-Bracket Mounted Pumps ( B Drive) See Pages 34.3.6-34.3.9. MOTOR MOUNTED UNITS ( M DRIVE) Series SG-04, -05 & -07 pumps may be close coupled to NEMA-C faced motors and SG-0 & -4 to both NEMA-C and IEC B5 flanged motors to provide an easily-assembled, compact pumping unit. This mounting arrangement eliminates the need for on-site coupling alignment that is normally required for a basemounted unit. Dimensions for Motor Mounted Pumps ( M Drive) See Pages 34.3.0-34.3.4. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
Section 34.3 Page 34.3.6 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-04, SG-05 AND SGN-05 (MD-A_ B DRIVE) FOOT BRACKET MOUNT MODEL NO. SG-047MD-A_B SG-04MD-A_B SG-0425MD-A_B SG-0435MD-A_B SG-0450MD-A_B SG-0470MD-A_B SG-05MD-A_B SGN-05MD-A_B SG-0525MD-A_B SGN-0525MD-A_B SG-0535MD-A_B SGN-0535MD-A_B SG-0550MD-A_B SGN-0550MD-A_B SG-0570MD-A_B SGN-0570MD-A_B SG-050MD-A_B SGN-050MD-A_B SG-054MD-A_B SGN-054MD-A_B SG-059MD-A_B SGN-059MD-A_B SG-052MD-A_B SGN-052MD-A_B A ¾ ¾ ¾ WITH R/V LESS R/V B C E B C E DD in 2.02 3.7 2.0 2.2 2.7 2.27 0.3 mm 5 34 53 56 323 5 in 2.02 3.7 2.0 2.2 2.7 2.27 0.3 mm 5 34 53 56 323 5 in 2.09 3.7 2.5 2.2 2.7 2.34 0.3 mm 53 350 55 5 325 59 in 2.9 3. 2.25 2.3 2. 2.44 0.3 mm 56 352 57 60 327 62 in 2.34 4.03 2.40 2.53 3.03 2.59 0.3 mm 59 356 6 64 33 66 in 2.54 4.23 2.60 2.73 3.23 2.79 0.3 mm 65 36 66 69 336 7 in 2.02 3.7 2.0 2.2 2.7 2.27 0.3 mm 5 34 53 56 323 5 in 2.09 3.7 2.5 2.2 2.7 2.34 0.3 mm 53 350 55 5 325 59 in 2.9 3. 2.25 2.3 2. 2.44 0.3 mm 56 352 57 60 327 62 in 2.34 4.03 2.40 2.53 3.03 2.59 0.3 mm 59 356 6 64 33 66 in 2.54 4.23 2.60 2.73 3.23 2.79 0.3 mm 65 36 66 69 336 7 in.4 4.53.90.4 3.53.90 0.3 mm 47 369 4 47 344 4 in 2.04 4.93 2.0 2.04 3.93 2.0 0.9 mm 52 379 53 52 354 53 5 in 2.29 5.43 2.35 2.29 4.43 2.35 0.9 mm 5 392 60 5 367 60 5 in 2.04 6.33 2.0 2.04 5.33 2.0 0.9 mm 52 45 53 52 39 53 5 VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3.7 DIMENSIONS SERIES SG-07 AND SGN-07 (MD-A_ B DRIVE) FOOT BRACKET MOUNT WITH R/V LESS R/V MODEL NO. A B C E B C E SG-074MD-A_B SGN-074MD-A_B in 3.07 5. 3.3 3.26 4.9 3.32 mm 7 402 0 3 360 4 SG-075MD-A_B SGN-075MD-A_B in 3.24 5.9 3.30 3.43 4.36 3.49 mm 2 406 4 7 365 9 SG-072MD-A_B SGN-072MD-A_B in 3.4 6.22 3.54 3.67 4.60 3.73 mm 42 90 93 37 95 SG-07MD-A_B SGN-07MD-A_B in 3. 6.55 3.7 4.00 4.93 4.06 mm 97 420 9 02 379 03 SG-076MD-A_B SGN-076MD-A_B in 4.3 7.05 4.37 4.50 5.43 4.56 mm 09 433 4 392 6 SG-0722MD-A_B SGN-0722MD-A_B S ¼ D in 4.25 20.20 4.3 4.25.5 4.3 mm 0 53 09 0 472 09 SG-0732MD-A_B SGN-0732MD-A_B S ¼ D in 4.2 20.72 4.34 4.27 9.0 4.33 mm 09 526 0 0 45 0 S = Suction Port D = Discharge Port VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
Section 34.3 Page 34.3. Issue B SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-07 AND SGN-07 (MD-B_ B DRIVE) FOOT BRACKET MOUNT WITH R/V LESS R/V MODEL NO. A B C E B C E SG-074MD-B_B SGN-074MD-B_B in 3.07 20.07 3.3 3.26.45 3.32 mm 7 50 0 3 469 4 SG-075MD-B_B SGN-075MD-B_B in 3.24 20.24 3.30 3.43.6 3.49 mm 2 54 4 7 473 9 SG-072MD-B_B SGN-072MD-B_B in 3.4 20.4 3.54 3.67.6 3.73 mm 520 90 93 479 95 SG-07MD-B_B SGN-07MD-B_B in 3. 20. 3.7 4.00 9.9 4.06 mm 97 529 9 02 47 03 SG-076MD-B_B SGN-076MD-B_B in 4.3 2.30 4.37 4.50 9.6 4.56 mm 09 54 4 500 6 SG-0722MD-B_B SGN-0722MD-B_B S ¼ D in 4.25 24.46 4.3 4.25 22.3 43 mm 0 62 09 0 50 09 SG-0732MD-B_B SGN-0732MD-B_B S ¼ D in 4.2 24.9 4.34 4.27 23.36 4.33 mm 09 634 0 0 593 0 S = Suction Port D = Discharge Port VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3.9 Issue B DIMENSIONS SERIES SG-0 (MD2-B_ B DRIVE) & SERIES SG-4 (MD2-C_ B DRIVE) FOOT BRACKET MOUNT PUMP AB W N R S A-PORTS X Y L Z B SG-009 5.35 (35.9) 2.06 (52.3) 0.5 (3.0).03 (26.2) M0.00" 6.42 (63.) SG-03 5.9 (50.) 2.3 (54.).90 (4.3) 0.70 (7.) M2.50" 4.50 (4.3) 3.63 (92.2) 6.9 (77.3) 6.63 (6.4) 3 (76.2) SG-026 6.3 (55.7) 2. (73.2).53 (3.9) 0.4 (2.3) M2 2.00" 7.20 (2.9) SG-420 6.0 (54.9) 2.37 (60.2) 0.4 (2.3).53 (3.9) M2 2.00" 7.04 (7.) SG-436 6.0 (72.7) 3.27 (3.).2 (30.7) 2.09 (53.) M6 3.00" 5.9 (3.) 3.63 (92.2) 7.74 (96.6) 7. (0.6) 4.5 (4.3) SG-456 7.9 (2.6) 4. (24.0).53 (3.9) 2.56 (65.0) M6 4.00".3 (206.5) DIMENSIONS FOR "U" MODELS (in.) Coupling D E F G H J K M O P T U V AD AE MD2-B (SG-0) 5.50 2.75 4. 7.00 6.4 0.56 2.2 7.60 0.53 0.7 2.72.25 0.25 9.30 2.7 MD2-C (SG-4) 6.69 3.75 5.75 0.00.53 0.945 2.50.4 0.76.40 4.07.75 0.50.20 5.50 DIMENSIONS FOR "M" MODELS (mm) Coupling D E F G H J K M O P T U V AD AE MD2-B (SG-0) 45 69.9.9 7 27.5 4.5 46 9 3.5 9 56.0 2 26 77.7 MD2-C (SG-4) 70 95.0 46.0 254 26.6 24.0 63 23 9.3 35.6 03.4 4 4 24 39.7 VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
Section 34.3 Page 34.3.0 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-04, SG-05 & SGN-05 (MD-A_ M DRIVE) NEMA C MOTOR MOUNT FOOTLESS BRACKET NOTE: Footless bracket requires footed motor. MODEL NO. A WITH R/V LESS R/V B C B C MOTOR FRAME SIZE DD D E F H J MC SG-047MD-A_M SG-04MD-A_M SG-0425MD-A_M SG-0435MD-A_M SG-0450MD-A_M SG-0470MD-A_M SG-05MD-A_M SGN-05MD-A_M SG-0525MD-A_M SGN-0525MD-A_M SG-0535MD-A_M SGN-0535MD-A_M SG-0550MD-A_M SGN-0550MD-A_M SG-0570MD-A_M SGN-0570MD-A_M SG-050MD-A_M SGN-050MD-A_M SG-054MD-A_M SGN-054MD-A_M SG-059MD-A_M SGN-059MD-A_M SG-052MD-A_M SGN-052MD-A_M ¾ ¾ ¾ in 2.02 9.5 2.2.5 mm 5 232 56 207 in 2.02 9.5 2.2.5 mm 5 232 56 207 in 2.09 9.22 2.2.22 mm 53 234 5 209 in 2.9 9.32 2.3.32 mm 56 237 60 2 in 2.34 9.47 2.53.47 mm 59 24 60 25 in 2.54 9.67 2.73.67 mm 65 246 69 220 in 2.02 9.5 2.2.5 mm 5 232 56 207 in 2.09 9.22 2.2.22 mm 53 234 5 209 in 2.9 9.32 2.3.32 mm 56 237 60 2 in 2.34 9.47 2.53.47 mm 59 24 64 25 in 2.54 9.67 2.73.67 mm 65 246 69 220 in.4 9.97.4.97 mm 47 253 47 22 in 2.04 0.37 2.04 9.37 mm 52 263 52 23 in 2.29 0.7 2.29 9.7 mm 5 276 5 25 in 2.04.77 2.04 0.77 mm 52 299 52 274 56C 43TC 45TC 2TC 4TC 23TC* 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.9 5 0.9 5 0.9 5 3.50 2.44.50 0.34 SLOT 5.25 2.56 9 62 3 9 65 3.50 2.75 2.00 0.34 5.25 2. 9 70 5 9 73 3.50 2.75 2.50 0.34 5.25 2. 9 70 64 9 73 4.50 3.75 2.25 0.4 5.69 3.62 4 95 57 0 92 4.50 3.75 2.75 0.4 5.69 3.62 4 95 70 0 92 5.25 4.25 2.75 0.4 5.69 4.5 33 0 70 0 4 * Motor shaft must be modified to resemble 2TC-4TC shaft length, diameter and key. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3. DIMENSIONS SERIES SG-07 AND SGN-07 (MD-A_ M DRIVE) NEMA C MOTOR MOUNT FOOTLESS BRACKET NOTE: Footless bracket requires footed motor. See page 34.3. for optional footed MD-A brackets. MODEL NO. A WITH R/V LESS R/V B C B C MOTOR FRAME SIZE D E F H J MC SG-074MD-A_M SGN-074MD-A_M in 3.07.25 3.26 9.63 mm 7 26 3 245 56C 3.50 2.44.50 0.34 SLOT 5.25 2.56 9 62 3 9 65 SG-075MD-A_M SGN-075MD-A_M in 3.24.42 3.43 9.0 mm 2 290 7 249 43TC 3.50 2.75 2.00 0.34 2. 5.25 9 70 5 9 73 SG-072MD-A_M SGN-072MD-A_M in 3.4.66 3.67 0.04 mm 296 93 255 45TC 3.50 2.75 2.50 0.34 2. 5.25 9 70 64 9 73 SG-07MD-A_M SGN-07MD-A_M in 3..99 4.00 0.37 mm 97 305 02 263 2TC 4.50 3.75 2.25 0.4 5.69 3.62 4 95 57 0 92 SG-076MD-A_M SGN-076MD-A_M SG-0722MD-A_M SGN-0722MD-A_M S ¼D in 4.3 2.49 4.50 0.7 mm 09 37 4 276 in 4.25 5.64 4.25 5.02 mm 0 397 0 356 4TC 23TC* 4.50 3.75 2.75 0.4 3.62 5.69 4 5 70 0 92 5.25 4.25 2.75 0.4 4.50 5.69 33 0 70 0 4 SG-0732MD-A_M SGN-0732MD-A_M S ¼D in 4.75 6.64 4.75 5.02 mm 2 423 2 32 * Motor shaft must be modified to resemble 2TC-4TC shaft length, diameter and key. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
Section 34.3 Page 34.3.2 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-07 AND SGN-07 (MD-A_ M DRIVE) NEMA C MOTOR MOUNT FOOTED BRACKET NOTE: Footed bracket requires footless motor. See pages 34.3.9-34.3.0 for optional footless MD-A brackets. MODEL NO. SG-074MD-A_M SGN-074MD-A_M SG-075MD-A_M SGN-075MD-A_M A B WITH R/V C E B LESS R/V C E MOTOR FRAME SIZE in 3.07.25 3.3 3.26 9.63 3.32 mm 7 26 0 3 245 4 in 3.24.42 3.30 3.43 9.0 3.49 mm 2 290 4 7 249 9 SG-072MD-A_M SGN-072MD-A_M SG-07MD-A_M SGN-07MD-A_M SG-076MD-A_M SGN-076MD-A_M in 3.4.66 3.54 3.67 0.04 3.73 mm 269 90 93 255 95 in 3..99 3.7 4.00 0.37 4.06 mm 97 305 9 02 263 03 in 4.3 2.49 4.37 4.50 0.7 4.56 mm 09 37 4 276 6 56C 43TC 45TC SG-0722MD-A_M SGN-0722MD-A_M S ¼D in 4.25 5.64 4.3 4.25 4.02 4.3 mm 0 397 09 0 356 09 SG-0732MD-A_M SGN-0732MD-A_M S ¼D in 4.75 6.64 4. 4.75 5.02 4. mm 2 423 22 2 32 22 S = Suction Port D = Discharge Port Footed bracket is only available for up to NEMA 45TC frame motors (4.5 rabbet) - 0TC and 20TC motor frames with.5 rabbet are only available with footless bracket. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3.3 DIMENSIONS SERIES SG-07 AND SGN-07 (MD-B_ M DRIVE) NEMA C MOTOR MOUNT FOOTED BRACKET NOTE: Footed bracket requires footless motor. No footless brackets available with MD-B couplings. MODEL NO. SG-074MD-B_M SGN-074MD-B_M SG-075MD-B_M SGN-075MD-B_M A B WITH R/V C E B LESS R/V C E MOTOR FRAME SIZE in 2.60 3.97 3.79 2.0 2.35 3.9 mm 66 355 96 7 34 0 in 2.77 4.4 3.96 2.97 2.52 4.5 mm 70 359 0 75 3 05 SG-072MD-B_M SGN-072MD-B_M SG-07MD-B_M SGN-07MD-B_M SG-076MD-B_M SGN-076MD-B_M in 3.0 4.3 4.20 3.2 2.76 4.39 mm 76 365 07 2 324 2 in 3.34 4.7 4.53 3.54 3.09 4.72 mm 5 374 5 90 332 20 in 3.4 5.20 5.03 4.04 3.59 5.22 mm 9 36 2 03 345 33 2TC/4TC 23TC/25TC 254TC/256TC SG-0722MD-B_M SGN-0722MD-B_M S ¼D in 3.7.35 4.97 3.7 6.73 4.97 mm 96 466 26 96 425 26 SG-0732MD-B_M SGN-0732MD-B_M S ¼D in 4.2 9.35 5.47 4.2 7.73 5.47 mm 09 49 39 09 450 39 S = Suction Port D = Discharge Port Coupling will accept NEMA motor frames 2TC-256TC. NEMA 254TC-256TC will require shaft modification reducing shaft extension by ⅝. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
Section 34.3 Page 34.3.4 SERIES SG-04, -05, -07, -0, -4 (Cast Iron) DIMENSIONS SERIES SG-0 (MD2-B_ M DRIVE) & SERIES SG-4 (MD2-C_ M DRIVE) NEMA C AND IEC MOTOR MOUNT FOOTED BRACKET PUMP AB W N R S A-PORTS X Y L Z B SG-009 5.35 (35.9) 2.06 (52.3) 0.5 (3.0).03 (26.2) M0.00" 6.42 (63.) SG-03 5.9 (50.) 2.3 (54.).90 (4.3) 0.70 (7.) M2.50" 4.50 (4.3) 3.63 (92.2) 6.9 (77.3) 6.63 (6.4) 3 (76.2) SG-026 6.3 (55.7) 2. (73.2).53 (3.9) 0.4 (2.3) M2 2.00" 7.20 (2.9) SG-420 6.0 (54.9) 2.37 (60.2) 0.4 (2.3).53 (3.9) M2 2.00" 7.04 (7.) SG-436 6.0 (72.7) 3.27 (3.).2 (30.7) 2.09 (53.) M6 3.00" 5.9 (3.) 3.63 (92.2) 7.74 (96.6) 7. (0.6) 4.5 (4.3) SG-456 7.9 (2.6) 4. (24.0).53 (3.9) 2.56 (65.0) M6 4.00".3 (206.5) DIMENSIONS FOR "U" MODELS FOR NEMA C FACE MOTORS (in.) Coupling NEMA Drive D E F G H J O P AD MD2-B (SG-0) MD2-C (SG-4) 2/4TC 5.50 2.75 4.25 7.00 5.7 0.56 0.53 0.7.92 23/25TC 5.50 2.75 4. 7.00 6.4 0.56 0.53 0.7 9.30 254/256TC 6.50 2.75 5.50 7.00 7.03 0.56 0.53 0.7 9.92 23 thru 256TC 6.69 3.75 5.75 0.00.53 0.945 0.76.40.95 24/26TC 6.69 3.75 5.75 0.00.53 0.945 0.76.40 2.49 DIMENSIONS FOR "M" MODELS FOR IEC B5 FLANGE MOTORS (mm) Requires unfooted motor. Coupling IEC Drive D E F G H J O P AD MD2-B (SG-0) MD2-C (SG-4) 00/2 45 69.9.9 7 27.5 4.5 3.5 9 26 32 70 69.9 0.0 7 46.3 4.5 3.5 9 236 32 70 95.0 46.0 254 26.6 24.0 9.3 35.6 24 60/0 203 20.0 65.0 305 235.0 24.0 9.3 35 34 VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3.5 PERFORMANCE CURVE NOTES Printed performance curves are not available. Performance curves can be electronically generated with the Viking Pump Selector Program. This program can be located on www.vikingpump.com/pumpselector for the general public. For authorized distributors, this program can be found listed under the Products tab at www.idexconnect.com. Security passwords are required to access IDEXconnect. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 200