vailable in a wide range of spray angles and flows. Liquid is forced through an oval or eliptical orifice to form a sheet of spray that breaks into ligaments and then droplets or is atomised by impacting onto a curved deflector plate. To create a consistent spray along a spray bar from several nozzles, choose a tapering pattern and overlap by 50%. djust the spray distance to achieve a precise overlap. Flat Fan nozzles can be used fo washing, rinsing and surface treatments including high pressure nozzles used at up to 200 bar. 13
M Series haracteristics high impact spray of coarser droplets. onstructed with a hex body for ease of fitting without damaging the nozzle orifice and with no internal parts reducing the risk of clogging. Male and female SP or NPT thread options. lso available as a shorter stubby (HM) option, which is ideal where space is restricted. M Standard Spray ngles 0, 15, 25, 40, 65, 80, 90, 110 at 3 bar are available in even and flat fan spray patterns, greater impact is achieved at narrower spray angles. Note: Spray angle will vary with pressure. rass (E2) or 316 Stainless Steel (S6) standard. onnections oarse Stubby M Thread (mm) (mm) (mm) ⅛ 19.5 11.4 10 ¼ 25.4 15 12.7 ⅜ 28.5 18 14.3 ½ 35 23.4 17.5 ¾ 38 27.9 19 1 51 37.6 25.4 pplications hemical Male SP/NPT Rates ontrol/misting Thread (mm) (mm) (mm) ¼ 12.0 15.3 5.0 ¾ 23.0 31.0 10.3 Thread onnection (L/min) Pressure (bar) ⅛ ¼ ⅜ ½ ¾ 1 0.5 1 2 3 4 5 7 10 20 30 M01 X X 0.16 0.23 0.33 0.40 0.46 0.52 0.61 0.73 1.03 1.26 M015 X X 0.24 0.35 0.49 0.60 0.69 0.77 0.92 1.10 1.55 1.90 M02 X X 0.33 0.46 0.65 0.80 0.92 1.03 1.22 1.46 2.07 2.53 M03 X X 0.49 0.69 0.98 1.20 1.39 1.55 1.83 2.19 3.10 3.79 M04 X X 0.65 0.92 1.31 1.60 1.85 2.07 2.44 2.92 4.13 5.06 M045 X X 0.73 1.04 1.47 1.80 2.08 2.32 2.75 3.29 4.65 5.69 M05 X X 0.82 1.15 1.63 2.00 2.31 2.58 3.06 3.65 5.16 6.32 M055 X X 0.90 1.27 1.80 2.20 2.54 2.84 3.36 4.02 5.68 6.96 M06 X X 0.98 1.39 1.96 2.40 2.77 3.10 3.67 4.38 6.20 7.59 M065 X X 1.06 1.50 2.12 2.60 3.00 3.36 3.97 4.75 6.71 8.22 M07 X X 1.14 1.62 2.29 2.80 3.23 3.61 4.28 5.11 7.23 8.85 M08 X X 1.31 1.85 2.61 3.20 3.70 4.13 4.89 5.84 8.26 10.1 M09 X X 1.47 2.08 2.94 3.60 4.16 4.65 5.50 6.57 9.30 11.3 M10 X X 1.63 2.31 3.27 4.00 4.62 5.16 6.11 7.30 10.3 12.6 M15 X X 2.45 3.46 4.90 6.00 6.93 7.75 9.17 10.9 15.4 18.9 M20 X X 3.27 4.62 6.53 8.00 9.24 10.3 12.2 14.6 20.6 25.3 M30 X 4.90 6.93 9.80 12.0 13.8 15.4 18.3 21.9 30.9 37.9 M40 X X 6.53 9.24 13.0 16.0 18.4 20.6 24.4 29.2 41.3 50.6 M50 X X 8.16 11.5 16.3 20.0 23.0 25.8 30.5 36.5 51.6 63.2 M60 X X 9.80 13.8 19.6 24.0 27.7 30.9 36.6 43.8 61.9 75.8 M70 X X 11.4 16.1 22.8 28.0 32.3 36.1 42.7 51.1 72.3 88.5 M80 X X 13.0 18.4 26.1 32.0 36.9 41.3 48.8 58.4 82.6 101 M100 X X X 16.3 23.0 32.6 40.0 46.1 51.6 61.1 73.0 103 126 M150 X X 24.4 34.6 48.9 60.0 69.2 77.4 91.6 109 154 189 M200 X X 32.6 46.1 65.3 80.0 92.3 103 122 146 206 252 M250 X 40.8 57.7 81.6 100 115 129 152 182 258 316 M300 X X 48.9 69.2 97.9 120 138 154 183 219 309 379 M400 X X 65.3 92.3 130 160 184 206 244 292 413 505 M500 X 81.6 115 163 200 230 258 305 365 516 632 M600 X 97.9 138 195 240 277 309 366 438 619 758 Example part number (see page 63).. E2 2 M 03 E 80 For nozzle holders suitable for threaded nozzles see page 40. These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 3 bar. 14
M Series (Plastic) haracteristics high impact spray of coarser droplets. vailable in PVDF with a male ⅛ or ¼ SP / NPT thread. lso offered in polyacetal with a ⅜ push-fit spigot in an assembly that includes an anti-drip check valve and a 200 mesh nozzle filter. M Standard Spray ngles nozzles are available with even spray 0, 25, 40, 65 or 80 angles. nozzles available with 45 even spray pattern or 80 flat fan spray pattern. Note: Spray angle will vary with pressure. in PVDF (90), in polyacetal (30). onnections Fine - oarse Push Fit M Thread (mm) (mm) (mm) ⅛ * 21.7 12.45 12.2 ¼ 26.5 13.9 14.0 * Up to M20, minimum order quantity applies pplications hemical Male (SP/NPT) ontrol/misting Thread (mm) (mm) (mm) ⅜ 27.9 9.2 11.2 Rates - M (PVDF) * Thread onnection (L/min) @ Pressure (bar) (M SP) ⅛ ¼ 0.5 1 2 3 4 5 7 M02 Orange x x 0.33 0.46 0.65 0.80 0.92 1.03 1.22 M03 Red x x 0.49 0.69 0.98 1.20 1.39 1.55 1.83 M04 amb lue x x 0.65 0.92 1.31 1.60 1.85 2.07 2.44 M05 Yellow x x 0.82 1.15 1.63 2.00 2.31 2.58 3.06 M06 Lime Green x x 0.98 1.39 1.96 2.40 2.77 3.10 3.67 M08 Moss Green x x 1.31 1.85 2.61 3.20 3.70 4.13 4.89 M10 Royal lue x x 1.63 2.31 3.27 4.00 4.62 5.16 6.115 M15 Emerald Green x x 2.45 3.46 4.90 6.00 6.93 7.75 9.17 M20 Olive Green x x 3.27 4.62 6.53 8.00 9.24 10.3 12.2 M30 Red x 4.90 6.93 9.80 12.0 13.8 15.4 18.3 M40 amb lue x 6.53 9.24 13.0 16.0 18.4 20.6 24.4 M50 Yellow x 8.16 11.5 16.3 20.0 23.0 25.8 30.5 * Running change underway to grey colour for all sizes Example part number (see page 63). 90 2 M 03 E 80 For nozzle holders suitable for threaded nozzles, see page 40. Datum Pressure 3 bar. Rates - Push Fit M and Holders Spray Part Number Description ngle onnection l/min @ 7bar olour 30PFM002F80 Push Fit M 02 80 fan white 80 0.189 white 30PFM002F80L Push Fit M 02 80 fan black 80 0.189 black 30PFM005E45 Push Fit M 05 45 evenspray white 45 9.4mm spigot 0.284 white LU30PFM005F80 Push Fit M 05 80 fan white 80 to suit 7/8 0.284 white LU30PFM005F80 Push Fit M 05 80 fan black 80 Push Fit fitting 0.284 black LU30Q3107 Push Fit blanking nozzle black n/a n/a black LU30Q3107K1 Push Fit blanking nozzle white n/a n/a white 03N869 Push Fit T nozzle holder 15mm n/a 3 / 8 socket n/a black Push-fit M holder Datum Pressure 3 bar. 15
SN Series haracteristics high impact spray of coarser droplets. Non-clogging, one piece construction with precision machined deflector plate for maximum impact and washing effectiveness. vailable in a range of male SP or NPT threads. SN Series Standard Spray ngles 15, 25, 35, 40 and 50 at 3 bar are available in an even spray pattern. Note: Spray angle will vary with pressure. rass (E2), 303 Stainless Steel (S3) and 316 Stainless Steel (S6). onnections oarse Pipe Size SP (mm) (mm) (mm) ⅛ 40.0 20.0 30.0 ¼ 54.0 20.8 41.0 ⅜ 92.0 45.0 77.0 ½ 137 28.0 120 ¾ 150 32.0 131 Male (SP/NPT) Note - SN nozzles vary with pipe size, flow rate and angle - the maximum size envelope is shown in this table. pplications hemical ontrol/misting Rates Thread onnection (L/min) @ Pressure (bar) ⅛ ¼ ⅜ ½ ¾ 1 2 3 4 5 7 10 15 35 50 SN4 x 0.91 1.29 1.58 1.82 2.04 2.4 2.88 x SN10 x 2.28 3.22 3.95 4.56 5.10 6.03 7.21 x x x SN20 x x 4.56 6.45 7.90 9.12 10.1 12.0 14.4 x x SN25 x 5.70 8.06 9.87 11.4 12.7 15.0 18.0 x SN40 x 9.12 12.8 15.7 18.2 20.3 24.1 28.8 x x x SN50 x 11.4 16.1 19.7 22.7 25.4 30.1 36.0 x SN60 x x 13.6 19.3 23.6 27.3 39.5 36.1 43.2 x x x SN80 x x 18.2 25.7 31.5 36.4 40.7 48.2 57.6 x Spray ngle @ 3 bar SN100 x x 22.7 32.2 39.4 45.5 50.9 60.3 72.0 x x SN160 x 36.4 51.5 63.1 72.9 81.5 96.4 115 x SN 200 x x 45.5 64.4 78.9 91.1 101 120 144 x Example part number (see page 63) E2 2 SN 25 E 40 For nozzle holders suitable for threaded nozzles, see page 40. These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 3 bar. 16
F/E Series haracteristics medium impact spray available in a range of droplet spectrums. Single piece construction. for use in a threaded holder with a cap nut or in a bayonet cap with locked spray fan orientation. F / E Series Tip Medium Standard Spray ngles 0, 15, 25, 40, 65, 80 and 110 at 3 bar are available in even and flat fan spray patterns. Greater impact is achieved at narrower spray angles. Note: Spray angle will vary with pressure. rass (E2), 303 Stainless Steel (S3), Polyacetal (30) and PVDF (90). onnections pplications hemical Medium Fine-oarse ontrol/misting F / E Series: omplete unit in 4 piece holder (see page 37) E (mm) (mm) (mm) 9.65 14.7 12.5 F D Male H G Female Thread Male (mm) Female (mm) D E F G H I ⅛ 44.0 21.0 30.0 44.0 21.0 23.0 ¼ 44.0 21.0 30.0 44.0 21.0 23.0 ⅜ 44.0 21.0 30.0 44.0 21.0 23.0 II Rates NOZZLE REFERENE Tapered Evenspray (L/min) @ Pressure (bar) 0.5 1 2 3 4 5 7 10 20 30 005F 005E 0.08 0.12 0.16 0.20 0.23 0.26 0.31 0.37 0.52 0.63 0067F 0067E 0.11 0.15 0.22 0.27 0.31 0.35 0.41 0.49 0.69 0.85 0077F 0077E 0.13 0.18 0.25 0.31 0.36 0.40 0.47 0.56 0.80 0.97 01F 01E 0.16 0.23 0.33 0.40 0.46 0.52 0.61 0.73 1.03 1.26 015F 015E 0.24 0.35 0.49 0.60 0.69 0.77 0.92 1.10 1.55 1.90 02F 02E 0.33 0.46 0.65 0.80 0.92 1.03 1.22 1.46 2.07 2.53 03F 03E 0.49 0.69 0.98 1.20 1.39 1.55 1.83 2.19 3.10 3.79 04F 04E 0.65 0.92 1.31 1.60 1.85 2.07 2.44 2.92 4.13 5.06 05F 05E 0.82 1.15 1.63 2.00 2.31 2.58 3.06 3.65 5.16 6.32 06F 06E 0.98 1.39 1.96 2.40 2.77 3.10 3.67 4.38 6.20 7.59 08F 08E 1.31 1.85 2.61 3.20 3.70 4.13 4.89 5.84 8.26 10.1 10F 10E 1.63 2.31 3.27 4.00 4.62 5.16 6.11 7.30 10.3 12.6 15F 15E 2.45 3.46 4.90 6.00 6.93 7.75 9.17 10.9 15.4 18.9 20F 20E 3.27 4.62 6.53 8.00 9.24 10.3 12.2 14.6 20.6 25.3 Example part number (see page 63) E2 05 F 65 For nozzle holders and caps suitable for flanged nozzles, see pages 37. an be assembled into a 4 piece unit including spray tip, nozzle body, filter and cap nut or a fixed orientation bayonet cap. These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 3 bar. 17
N Series haracteristics medium impact wide angled spray of coarser droplets. One piece design deflects spray at 75 from inlet orifice. log resistant making the N suitable for use with a wide range of fluids. Hex body to reduce risk of damaging orifice during fitting. range of male thread options are offered. N Series - Medium Standard Spray ngles Standard angles 115, 125 and 145 at 1.5 bar. Spray angle will vary with pressure. rass (E2), 316 Stainless Steel (S6). onnections pplications Male (SP/NPT) oarse Thread (mm) (mm) (mm) ⅛ 29.1* 13.3 19.4 ¼ 34.0 15.3 21.4 ⅜ 45.9 23.4 31.7 ½ 47.6 23.4 30.1 ¾ 60.3 28.0 40.0 1 73.0 37.6 49.2 * shorter body is available on request hemical ontrol/misting Rates Thread onnection (L/min) @ Pressure (bar) ⅛ ¼ ⅜ ½ ¾ 1 0.5 1.0 1.5 2.0 2.5 3.0 4.0 N0.5 X 0.16 0.23 0.28 0.32 0.36 0.39 0.46 110 * N0.8 X 0.24 0.34 0.40 0.48 0.54 0.59 0.68 115 N1.0 X 0.32 0.46 0.56 0.64 0.72 0.79 0.91 115 N1.5 X 0.48 0.68 0.84 0.97 1.08 1.18 1.37 115 N2.0 X X 0.64 0.91 1.12 1.29 1.44 1.58 1.82 115 N2.5 X X 0.81 1.14 1.40 1.61 1.80 1.97 2.28 115 N3.0 X X 0.97 1.37 1.68 1.93 2.16 2.37 2.74 125 N4.0 X X 1.29 1.82 2.23 2.58 2.88 3.16 3.65 125 N5.0 X X 1.61 2.28 2.79 3.22 3.60 3.95 4.56 125 N7.5 X X 2.42 3.42 4.19 4.84 5.41 5.92 6.84 145 N10 X X 3.22 4.56 5.58 6.45 7.21 7.90 9.12 145 N15 X X 4.84 6.84 8.38 9.67 10.8 11.8 13.6 145 N20 X X X 6.45 9.12 11.1 12.8 14.4 15.7 18.2 145 N25 X X 8.06 11.4 13.9 16.1 18.0 19.7 22.7 145 N30 X 9.57 13.8 16.7 19.3 21.6 23.6 27.3 145 N35 X 11.2 15.9 19.5 22.5 25.2 27.6 31.9 145 N40 X X 12.8 18.2 22.3 25.7 28.8 31.5 36.4 145 N50 X 16.1 22.7 27.9 32.2 36.0 39.4 46.5 145 N60 X X 19.3 27.3 33.5 38.6 43.2 47.3 54.7 145 N80 X X 25.7 36.4 44.6 51.5 57.6 63.1 72.9 145 N100 X X 32.2 45.5 55.8 64.4 72.0 78.9 91.1 145 N120 X 38.6 54.7 67.0 77.3 86.5 94.7 109 145 N160 X 51.5 72.9 89.3 103 115 126 145 145 N210 X 67.7 95.7 117 135 151 165 191 145 N300 X 96.7 136 167 193 216 236 273 145 N450 X 145 205 251 290 324 355 410 145 Spray ngle @ 1.5 bar *t 3 bar Example part nuimber (see page 63) E2 2 N 4.0 E 125 For nozzle holders suitable for threaded nozzles see page 40. These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 0.7 bar. 18
N Series haracteristics low impact wide angled spray of coarser droplets. One piece design deflects spray at 75 from inlet orifice. log resistant making the N suitable for use with a wide range of fluids. Flange fitting for use in a threaded holder with cap nut or in a bayonet cap. N Series - Flange Tip Standard Spray ngles Standard angles 80 to 145 at 1.5 bar. Spray angle will vary with pressure. Medium 316 Stainless Steel (S6), polyacetal (30), rass (E2). onnections pplications hemical Male oarse ontrol/misting (mm) (mm) (mm) 18.0 14.7 12.5 N Series - Flange: omplete unit in 4 piece holder (see page 37) E D Male F I H Female G Male (mm) Female (mm) Thread D E F G H I ⅛ 53.0 21.0 39.0 53.0 21.0 31.0 ¼ 53.0 21.0 39.0 53.0 21.0 31.0 ⅜ 53.0 21.0 39.0 53.0 21.0 31.0 Rates (l/min) @ Pressure (bar) Spray ngle @ 1 bar 0.5 1.0 1.5 2.0 2.5 3.0 4.0 Metal cetal N0.5 0.16 0.23 0.28 0.32 0.36 0.39 0.46 110 * 80 N0.75 0.24 0.34 0.42 0.48 0.54 0.59 0.68 115 95 N1.0 0.32 0.46 0.56 0.64 0.72 0.79 0.91 115 105 N1.5 0.48 0.68 0.84 0.97 1.08 1.18 1.37 115 105 N2.0 0.64 0.91 1.12 1.29 1.44 1.58 1.82 115 105 N2.5 0.81 1.14 1.40 1.61 1.80 1.97 2.28 115 110 N3.0 0.97 1.37 1.68 1.93 2.16 2.37 2.74 125 110 N4.0 1.29 1.82 2.23 2.58 2.88 3.16 3.65 125 120 N5.0 1.81 2.28 2.79 3.22 3.60 3.95 4.56 125 145 N7.5 2.42 3.42 4.19 4.84 5.41 5.92 6.84 145 145 N10 3.22 4.56 5.58 6.45 7.21 7.90 9.12 145 145 N15 4.84 6.84 8.38 9.67 10.8 11.8 13.6 145 145 N20 6.45 9.12 11.1 12.8 14.4 15.7 18.2 145 145 Example part number (see page 63) S6 N 3.0 E 125 For nozzle holders and caps suitable for flanged nozzles, see page 37. an be assembled into a 4 piece unit including spray tip, nozzle body, filter and cap nut or a fixed orientation bayonet cap. These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 0.7 bar. 19
Pro TM HP Series haracteristics very high impact spray for highly effective and efficient pressure washing operations using the minimum water and pump power. One piece design with male ¼ or ⅛ SP or NPT thread options. The hex body makes for fast fitting without the risk of distortion of the nozzle orifice. Part numbers are permanently etched on the nozzle face for ease of identification when fitted in spraying location. Pro TM Series Very Standard Spray ngles 0, 15, 25 and 40 at 70 bar with popular flow rates are held in stock with others available to order. Note: Spray angle will vary with pressure. Hardened 416 Stainless Steel. onnections oarse Thread (mm) (mm) (mm) ⅛ 22.0 14.0 12.0 ¼ 22.0 14.0 12.0 pplications Male (SP/NPT) hemical ontrol/misting Rates (l/min) @ Pressure (bar) 15 20 30 40 50 60 70 80 100 150 200 02 1.77 2.04 2.50 2.88 3.22 3.53 3.81 4.08 4.56 5.58 6.45 025 2.21 2.55 3.12 3.60 4.03 4.41 4.77 5.10 5.70 6.98 8.06 030 2.65 3.06 3.75 4.32 4.84 5.30 5.72 6.12 6.84 8.38 9.67 035 3.09 3.57 4.37 5.05 5.64 6.18 6.67 7.14 7.98 9.77 11.2 04 3.53 4.08 4.99 5.77 6.45 7.06 7.63 8.16 9.12 11.1 12.8 045 3.97 4.59 5.62 6.49 7.25 7.95 8.58 9.17 10.2 12.5 14.5 05 4.41 5.10 6.24 7.21 8.06 8.83 9.54 10.1 11.4 13.9 16.1 055 4.86 5.61 6.87 7.93 8.86 9.71 10.4 11.2 12.5 15.3 17.7 06 5.30 6.12 7.49 8.65 9.67 10.5 11.4 12.2 13.6 16.7 19.3 065 5.74 6.63 8.12 9.37 10.4 11.4 12.4 13.2 14.8 18.1 20.9 07 6.18 7.14 8.74 10.0 11.2 12.3 13.3 14.2 15.9 19.5 22.5 075 6.62 7.65 9.36 10.8 12.0 13.2 14.3 15.2 17.1 20.9 24.1 08 7.06 8.16 9.99 11.5 12.8 14.1 15.2 16.3 18.2 22.3 25.7 085 7.50 8.66 10.6 12.2 13.7 15.0 16.2 17.3 19.3 23.7 27.4 09 7.95 9.17 11.2 12.9 14.5 15.8 17.1 18.3 20.5 25.1 29.0 10 8.83 10.1 12.4 14.4 16.1 17.6 19.0 20.3 22.7 27.9 32.2 11 9.71 11.2 13.7 15.8 17.7 19.4 20.9 22.4 25.0 30.7 35.4 12 10.5 12.2 14.9 17.3 19.3 21.1 22.8 24.4 27.3 33.5 38.6 13 11.4 13.2 16.2 18.7 20.9 22.9 24.7 26.5 29.6 36.2 41.9 14 12.3 14.2 17.4 20.1 22.5 24.7 26.7 28.5 31.9 39.0 45.1 15 13.2 15.2 18.7 21.6 24.1 26.4 28.6 30.5 34.1 41.8 48.3 16 14.1 16.3 19.9 23.0 25.7 28.2 30.5 32.6 36.4 44.6 51.5 18 15.8 18.3 22.4 25.9 29.0 31.7 34.3 36.7 41.0 50.2 58.0 20 17.6 20.3 24.9 28.8 32.2 35.3 38.1 40.7 45.5 55.8 64.5 To order -Pro nozzles, use HP followed by thread angle, nozzle ref and - SP, for NPT thread leave blank. For example: HP 1/4 15 10 SP For nozzle holders suitable for threaded nozzles, see page 40. These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 70 bar. 20
XT Series haracteristics coarse spray designed to be projected up to 5 metres from a moving vehicle creating a wide spray swath without the need for a spray boom. Useful for spraying where there are obstacles. Patented design achieves good distribution. vailable with male NPT threaded connections. Internal components are sold as replacement kits for easy maintenance. XT Series Standard Spray ngles 110 at 3 bar, designed to be sprayed horizontally. Spray angle will vary with pressure. 316 Stainless Steel or polyacetal. onnections pplications hemical Male (NPT) oarse ontrol/misting Thread (mm) (mm) (mm) ¼ 48.9 17.9 38.4 ⅜ 57.6 22.0 45.1 ½ 65.1 28.0 50.1 ¾ 81.4 35.0 64.4 Rates Thread onnection (NPT) (L/min) @ Pressure (bar) Swath Width (m) Ref @ 3 bar, ¼ ⅜ ½ ¾ 1 3 4 5 1.2m (water) XT010 x 3.90 4.60 10.1 3.90 XT020 x 7.90 9.12 10.1 4.80 XT024 x 9.48 10.9 12.2 4.90 XT043 x 16.9 19.6 21.9 4.40 XT080 x 31.5 36.4 40.7 3.90 XT167 x 65.9 76.1 85.1 4.30 XT215 x 84.8 98.0 109 4.90 To order XT nozzles use part numbers shown. For nozzle holders suitable for threaded nozzles, see page 40. These are our standard options. If your application requires a different spray angle than those shown, please contact us. 21
D Flat Fan s Series haracteristics high impact coarse spray designed specifically for use in continuous metal casting. Three piece construction with internal deflector plate produces a uniform spray. connection fits 1 cap nut. Series Medium oarse Standard Spray ngles 80 at 3 bar. Spray angle will vary with pressure. rass (E2). (mm) (mm) (mm) D (mm) 39.0 30.0 29.0 26.6 onnections Fits 1 ap Nut pplications hemical ontrol/misting Rates (l/min) @ Pressure (bar) 1 2 2.8 3 5 7 Spray ngle @ 3 bar 0500 3.01 4.26 5.00 5.21 6.73 7.97 80 1000 6.02 8.52 10.0 10.4 13.4 15.9 80 1500 9.03 12.7 15.0 15.6 20.2 23.9 80 2000 12.0 17.0 20.0 20.8 26.9 31.8 80 3000 18.0 25.5 30.0 31.2 40.3 47.7 80 Example part number: 1000 80 1 cap nut part number 28-Q2142 These are our standard options. If your application requires a different spray angle than those shown, please contact us. Datum Pressure 2.76 bar. 22