Fisher ES and EAS easy e Valves CL125 through CL600

Instruction Manual ES Valve Fisher ES and EAS easy e Valves CL25 through CL600 Contents Introduction... Scope of Manual... Description... 2 Specifications... 2 Installation... 2 Maintenance... 4 Packing Lubrication... 5 Packing Maintenance... 6 Replacing Packing... 6 Trim Maintenance... Disassembly... Lapping Metal Seats... 3 Valve Plug Maintenance... 3 Assembly... 3 ENVIRO SEAL Bellows Seal and Bonnet... 4 Replacing a Plain or Extension Bonnet with an ENVIRO SEAL Bellows Seal (Stem/Bellows Assembly) and Bonnet... 4 Replacement of an Installed ENVIRO SEAL Bellows Seal (Stem/Bellows Assembly)... 6 Purging the ENVIRO SEAL Bellows Seal Bonnet... 7 Parts Ordering... 7 Parts Kits... 7 Parts List... 2 Figure. Fisher ES Valve with 657 Actuator W274 3 Introduction Scope of Manual This instruction manual includes installation, maintenance, and parts information for NPS /2 through 8 Fisher ES valves, and NPS through 6 EAS valves, through CL600 ratings. Refer to separate manuals for instructions covering the actuator and accessories. Do not install, operate, or maintain an ES valve without being fully trained and qualified in valve, actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage, it is important to carefully read, understand, and follow all the contents of this manual, including all safety cautions and warnings. If you have any questions about these instructions, contact your Emerson sales office or Local Business Partner before proceeding. www.fisher.com

ES Valve Instruction Manual Table. Specifications End Connection Styles Cast Iron Valves Flanged: CL25 flat face or CL250 raised face flanges per ASME B6. Steel and Stainless Steel Valves Flanged: CL50, 300, and 600 raised face or ring type joint flanges per ASME B6.5 Screwed or Socket Welding: All available ASME B6. schedules that are consistent with CL600 per ASME B6.34 Buttwelding: Consistent with ASME B6.25 Shutoff Classifications See table 2 Flow Characteristics Standard Cages: Linear, quick opening, or equal percentage Whisper Trim and WhisperFlo Cages: Linear Flow Directions Standard Cages: Normally up Whisper Trim and WhisperFlo Cages: Always up Maximum Inlet Pressure () Cast Iron Valves Flanged: Consistent with CL25B or 250B pressure temperature ratings per ASME B6. Steel and Stainless Steel Valves Flanged: Consistent with CL50, 300, and 600 (2) pressure temperature ratings per ASME B6.34 Screwed or Welding: Consistent with CL600 pressure temperature ratings per ASME B6.34 Approximate Weights VALVE SIZE, NPS /2 and 3/4 and /4 /2 2 2 /2 3 4 6 8 kg 4 20 39 45 54 77 459 408 WEIGHT Pounds 25 30 45 67 00 25 70 350 900. The pressure/temperature limits in this manual and any applicable standard or code limitation for the valve should not be exceeded. 2. Certain bonnet bolting material selections may require a CL600 easy e valve assembly to be derated. Contact your Emerson sales office or Local Business Partner. Description These single port valves have cage guiding, quick change trim, and unbalanced push down to close valve plug action. Valve configurations are as follows: ES Globe style valve (figure ) with metal to metal seating as standard for all general applications over a wide range of pressure drops and temperatures, and metal to PTFE seating is optional for more stringent shutoff requirements. EAS Angle valve version of ES, used to facilitate piping or in applications where a self draining valve body is required. Specifications Typical specifications for these valves are shown in table. Installation WARNING Always wear protective gloves, clothing, and eyewear when performing any installation operations to avoid personal injury. Personal injury or equipment damage caused by sudden release of pressure may result if the valve assembly is installed where service conditions could exceed the limits given in table or on the appropriate nameplates. To avoid such injury or damage, provide a relief valve for over pressure protection as required by government or accepted industry codes and good engineering practices. 2

Instruction Manual ES Valve Check with your process or safety engineer for any additional measures that must be taken to protect against process media. If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this instruction manual. Table 2. Available Shutoff Classifications per ANSI/FCI 70 2 and IEC 60534 4 Seating Metal PTFE Shutoff Class IV (standard) V VI CAUTION When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature, pressure drop, and controlled fluid conditions. Since some body/trim material combinations are limited in their pressure drop and temperature ranges, do not apply any other conditions to the valve without first contacting your Emerson sales office or Local Business Partner. Before installing the valve, inspect the valve and pipelines for any damage and any foreign material which may cause product damage.. Before installing the valve, inspect the valve and associated equipment for any damage and any foreign material. 2. Make certain the valve body interior is clean, that pipelines are free of foreign material, and that the valve is oriented so that pipeline flow is in the same direction as the arrow on the side of the valve. 3. The control valve assembly may be installed in any orientation unless limited by seismic criteria. However, the normal method is with the actuator vertical above the valve. Other positions may result in uneven valve plug and cage wear, and improper operation. With some valves, the actuator may also need to be supported when it is not vertical. For more information, consult your Emerson sales office or Local Business Partner. 4. Use accepted piping and welding practices when installing the valve in the line. Internal elastomeric parts may stay in place during the welding procedure. For flanged valves, use a suitable gasket between the valve and pipeline flanges. CAUTION Depending on valve body materials used, post weld heat treating may be required. If so, damage to internal elastomeric and plastic parts, as well as internal metal parts is possible. Shrunk fit pieces and threaded connections may also loosen. In general, if post weld heat treating is to be performed, all trim parts should be removed. Contact your Emerson sales office or Local Business Partner for additional information. 5. With a leak off bonnet construction, remove the pipe plugs (keys 4 and 6, figure 8) to hook up the leak off piping. If continuous operation is required during inspection or maintenance, install a three valve bypass around the control valve assembly. 6. If the actuator and valve are shipped separately, refer to the actuator mounting procedure in the appropriate actuator instruction manual. WARNING Personal injury could result from packing leakage. Valve packing was tightened before shipment; however, the packing might require some readjustment to meet specific service conditions. 3

ES Valve Instruction Manual Valves with ENVIRO SEAL live loaded packing or HIGH SEAL Heavy Duty live loaded packing will not require this initial re adjustment. See the Fisher instruction manuals titled ENVIRO SEAL Packing System for Sliding Stem Valves or Heavy Duty Live Loaded Packing System (as appropriate) for packing instructions. If you wish to convert your present packing arrangement to ENVIRO SEAL packing, refer to the retrofit kits listed in the Parts Kits sub section near the end of this manual. Maintenance Valve parts are subject to normal wear and must be inspected and replaced as necessary. Inspection and maintenance frequency depends on the severity of service conditions. This section includes instructions for packing lubrication, packing maintenance, trim maintenance, and ENVIRO SEAL bellows seal replacement. All maintenance operations may be performed with the valve in the line. WARNING Avoid personal injury or damage to property from sudden release of pressure or uncontrolled process fluid. Before starting disassembly: Do not remove the actuator from the valve while the valve is still pressurized. Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal injury. Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the actuator cannot suddenly open the valve. Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure on both sides of the valve. Drain the process media from both sides of the valve. Vent the power actuator loading pressure and relieve any actuator spring compression. Use lock out procedures to be sure that the above measures stay in effect while you work on the equipment. The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from the pipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or when loosening the packing box pipe plug. Check with your process or safety engineer for any additional measures that must be taken to protect against process media. CAUTION Follow instructions carefully to avoid damaging the product surfaces, which could result in damage to the product. Note Whenever a gasket seal is disturbed by removing or shifting gasketed parts, a new gasket should be installed upon reassembly. This is necessary to ensure a good gasket seal since the used gasket may not seal properly. Note If the valve has ENVIRO SEAL or HIGH SEAL live loaded packing installed, refer to instruction manuals ENVIRO SEAL Packing System for Sliding Stem Valves, D0642X02, or HIGH SEAL Live Loaded Packing System (D0453X02), for packing 4

Instruction Manual ES Valve instructions. Figure 9 shows a typical HIGH SEAL Packing system. Figures 0,, and 2 show typical ENVIRO SEAL packing systems. If the valve has an ENVIRO SEAL bellows seal bonnet installed, refer to this manual. See the ENVIRO SEAL Bellows Seal and Bonnet section for information on the bellows seal bonnet. Figure 2. Optional Lubricator and Lubricator/Isolating Valve 0A942 A AJ5428 D A0832 2 LUBRICATOR LUBRICATOR/ISOLATING VALVE Table 3. Body to Bonnet Bolt Torque Guidelines VALVE SIZE, NPS BOLT TORQUES (, 4) ES EAS SA93 B7, SA93 B8M (3) SA93 B8M (2) N m Lbf ft N m Lbf ft /4 or less 29 95 64 47 /2, /2 x, 2, or 2 x 2 or 2 x 96 7 45 33 2 /2 or 2 /2 x /2 3 or 3 x /2 29 95 64 47 3, 3 x 2, or 3 x 2 /2 4 or 4 x 2 69 25 88 65 4, 4 x 2 /2, or 4 x 3 6 or 6 x 2 /2 27 200 56 5 6 549 405 366 270 8 746 550 529 390. Determined from laboratory tests. 2. SA93 B8M annealed. 3. SA93 B8M strain hardened. 4. For other materials, contact your Emerson sales office or Local Business Partner for torques. Packing Lubrication Note ENVIRO SEAL or HIGH SEAL packing does not require lubrication. WARNING To avoid personal injury or property damage resulting from fire or explosion, do not lubricate packing used in oxygen service or in processes with temperatures over 260 C (500 F). If a lubricator or lubricator/isolating valve (figure 2) is provided for PTFE/composition or other packings that require lubrication, it will be installed in place of the pipe plug (key 4, figure 8). Use a good quality silicon base lubricant. Packing used in oxygen service or in processes with temperatures over 260 C (500 F) should not be lubricated. To operate the lubricator, simply turn the cap screw clockwise to force the lubricant into the packing box. The lubricator/isolating valve operates the same way except the isolating valve must first be opened and then closed after lubrication is completed. 5

ES Valve Instruction Manual Packing Maintenance Key numbers refer to figure 3 for PTFE V ring packing and to figure 5 for PTFE/composition packing, unless otherwise indicated. For spring loaded single PTFE V ring packing, the spring (key 8, figure 3) maintains a sealing force on the packing. If leakage is noted around the packing follower (key 3, figure 3), check to be sure the shoulder on the packing follower is touching the bonnet. If the shoulder is not touching the bonnet, tighten the packing flange nuts (key 5, figure 8) until the shoulder is against the bonnet. If leakage cannot be stopped in this manner, proceed to the replacing packing procedure. If there is undesirable packing leakage with other than spring loaded packing, first try to limit the leakage and establish a stem seal by tightening the packing flange nuts. If the packing is relatively new and tight on the stem, and if tightening the packing flange nuts does not stop the leakage, it is possible that the valve stem is worn or nicked so that a seal cannot be made. The surface finish of a new valve stem is critical for making a good packing seal. If the leakage comes from the outside diameter of the packing, it is possible that the leakage is caused by nicks or scratches around the packing box wall. If performing any of the following procedures, inspect the valve stem and packing box wall for nicks and scratches. Replacing Packing WARNING Refer to the WARNING at the beginning of the Maintenance section in this instruction manual.. Isolate the control valve from the line pressure, and release pressure from the valve. 2. Disconnect the operating lines from the actuator and any leak off piping from the bonnet. Disconnect the stem connector, then remove the actuator from the valve by unscrewing the yoke locknut (key 5, figure 8) or the hex nuts (key 26, figure 8). WARNING To avoid personal injury or property damage caused by uncontrolled movement of the bonnet, loosen the bonnet by following the instructions in the next step. Do not remove a stuck bonnet by pulling on it with equipment that can stretch or store energy in any other manner. The sudden release of stored energy can cause uncontrolled movement of the bonnet. If the cage sticks to the bonnet, proceed carefully with bonnet removal. Note The following step also helps to provide additional assurance that the valve body fluid pressure has been relieved. 3. Hex nuts (key 5, figure 8) attach the bonnet to the valve. Loosen these nuts or cap screws approximately 3 mm (/8 inch). Then loosen the body to bonnet gasketed joint by either rocking the bonnet or prying between the bonnet and valve body. Work the prying tool around the bonnet until the bonnet loosens. 6

Instruction Manual ES Valve Figure 3. PTFE V Ring Packing Arrangements for Plain and Extension Bonnets UPPER WIPER (KEY 2) UPPER WIPER (KEY 2) PACKING FOLLOWER (KEY 3) FEMALE ADAPTOR FEMALE ADAPTOR PACKING FOLLOWER (KEY 3) WASHER (KEY 0) SPRING (KEY 8) PACKING RING MALE ADAPTOR PACKING RING MALE ADAPTOR SPACER (KEY 8) PACKING BOX RING (KEY ) PACKING BOX RING (KEY ) 2A7837 A LOWER WIPER LOWER WIPER FOR S3600 OR S7400 METAL PACKING BOX PARTS FOR ALL OTHER METAL PACKING BOX PART MATERIALS B2427 NOTE: PART OF PACKING SET (KEY 6) (SEE TABLE IN PARTS LIST). SINGLE ARRANGEMENTS UPPER WIPER (KEY 2) PACKING FOLLOWER (KEY 3) MALE ADAPTOR (KEY 3) PACKING RING (KEY 7) FEMALE ADAPTOR (KEY 32) LANTERN RING (KEY 8) PACKING BOX RING (KEY ) 2A887-D 2A784-D 2A7839-A ASSEMBLY (POSITIVE PRESSURES) ASSEMBLY 2 (VACUUM) ASSEMBLY (POSITIVE PRESSURES) ASSEMBLY 2 (VACUUM) B428 3 ASSEMBLY 3 (POSITIVE PRESSURES & VACUUM) ASSEMBLY 3 (POSITIVE PRESSURES & VACUUM) ASSEMBLY (POSITIVE PRESSURES) ASSEMBLY 2 (VACUUM) 9.5 mm (3/8 INCH) STEM 2.7 mm (/2 INCH) STEM 9., 25.4, or 3.8 mm (3/4,, OR /4 INCH) STEM DOUBLE ARRANGEMENTS ASSEMBLY 3 (POSITIVE PRESSURES & VACUUM) LOWER WIPER (KEY 30) 7

ES Valve Instruction Manual Figure 4. PTFE Packing Arrangements for Use in ENVIRO SEAL Bellows Seal Bonnets UPPER WIPER (KEY 2) BUSHING (KEY 3) PACKING SET: (KEY 6) FEMALE ADAPTOR PACKING RING MALE ADAPTOR THRUST RING (KEY 39) SPRING (KEY 8) THRUST RING SPACER (KEY 8) SPACER (KEY 8) 2B482-A SHT 2B485-A SHT 2B482-A SHT 2 2B485-A SHT 2 (KEY 39) 2.7 mm 9.5 mm 2.7 mm 9.5 mm (/2 INCH) (3/8 INCH) (/2 INCH) (3/8 INCH) STEM STEM STEM STEM FOR S3600 (36 SST) PACKING BOX PARTS SINGLE ARRANGEMENTS FOR ALL PACKING BOX MATERIALS EXCEPT S3600 BUSHING (KEY 3) BUSHING (KEY 3) SPACER (KEY 8) UPPER WIPER (KEY 2) BUSHING (KEY 3) PACKING SET: (KEY 6) FEMALE ADAPTOR PACKING RING MALE ADAPTOR THRUST RING 2B483-A (KEY 39) 8A0906-D 8A5338-A 9.5 mm (3/8 INCH) STEM A5863 2.7 mm (/2 INCH) STEM FOR NPS 2 VALVES DOUBLE ARRANGEMENTS SPACER (KEY 8) 2.7 mm (/2 INCH) STEM FOR NPS 3 AND 4 VALVES 4. Loosen the packing flange nuts (key 5, figure 8) so that the packing is not tight on the valve stem. Remove any travel indicator parts from the valve stem threads. CAUTION Avoid damage to the seating surface caused by the valve plug and stem assembly dropping from the bonnet after being lifted part way out. When lifting the bonnet, temporarily install a valve stem locknut on the valve stem. This locknut will prevent the valve plug and stem assembly from dropping out of the bonnet. If the cage starts to lift with the bonnet, tap it with a plastic mallet, or other soft material, to be sure it stays in the valve. 5. Completely remove the cap screws (not shown) or hex nuts (key 6; figure 3, 4, or 5) that bolt the bonnet and valve together and carefully lift the bonnet off. 6. Remove the locknut and separate the valve plug and stem from the bonnet. Set the parts on a protective surface to prevent damage to gasket or seating surfaces. 8

Instruction Manual ES Valve Figure 5. Detail of PTFE/Composition Packing Arrangements for Plain and Extension Bonnets 2A888 A 2A785 A 2A873 A A269 2 9.5 mm 2.7 mm (3/8 INCH) (/2 INCH) STEM STEM 9., 25.4, OR 3.8 mm (3/4,, OR /4 INCH) STEM UPPER WIPER (KEY 2) PACKING FOLLOWER (KEY 3) PACKING RING (KEY 7) LANTERN RING (KEY 8) PACKING BOX RING (KEY ) TYPICAL (DOUBLE) ARRANGEMENTS Figure 6. Double Graphite Ribbon/Filament Arrangements for use in ENVIRO SEAL Bellows Seal Bonnets BUSHING (KEY 3) GRAPHITE FILAMENT PACKING RING (KEY 7) GRAPHITE RIBBON PACKING RING (KEY 7) SPACER (KEY 8) Figure 7. Detail of Graphite Ribbon/Filament Packing for Plain and Extension Bonnets A5864 4A34-A 3A9775-B 3A9776-B 9.5 mm (3/8 INCH) STEM 2.7 mm (/2 INCH) STEM PACKING FOLLOWER (KEY 3) GRAPHITE RIBBON PACKING RING (KEY 7) GRAPHITE FILAMENT PACKING RING (KEY 7) LANTERN RING (KEY 8) PACKING BOX RING (KEY ) 9., 25.4, & 3.8 mm (3/4, & /4 INCH) STEM SINGLE ARRANGEMENTS 4A253-B 4A849-B 4A780-B 9.5 mm (3/8 INCH) STEM 2.7 mm (/2 INCH) STEM PACKING FOLLOWER (KEY 3) GRAPHITE RIBBON PACKING RING (KEY 7) GRAPHITE FILAMENT PACKING RING (KEY 7) LANTERN RING (KEY 8) PACKING BOX RING (KEY ) 9., 25.4, & 3.8 mm (3/4, & /4 INCH) STEM NOTE: 0.02 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS; USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING. DOUBLE ARRANGEMENTS 2B48-A 9.5 mm (3/8 INCH) STEM A5870 8A0909-D 2.7 mm (/2 INCH) STEM FOR NPS 2 VALVES 2B602-A 2.7 mm (/2 INCH) STEM FOR NPS 3 AND 4 VALVES NOTE: 0.02 mm (0.004 INCH) THICK SACRIFICIAL ZINC WASHERS; USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING. WARNING To avoid personal injury due to leaking fluid, avoid damaging gasket sealing surfaces. The seating surface of the valve plug (key 2) is critical for proper shutoff. Protect these surfaces accordingly. 9

ES Valve Instruction Manual CAUTION To prevent possible product damage, cover the opening in the valve in the following procedure to prevent foreign material from getting into the valve body cavity. 7. Remove the bonnet gasket (key 0, figure 3 through 5) and cover the opening in the valve to protect the gasket surface and prevent foreign material from getting into the valve body cavity. 8. Remove the packing flange nuts, packing flange, upper wiper, and packing follower (keys 5, 3, 2, and 3, figure 8). Carefully push out all the remaining packing parts from the valve side of the bonnet using a rounded rod or other tool that will not scratch the packing box wall. Clean the packing box and the metal packing parts. 9. Inspect the valve stem threads and packing box surfaces for any sharp edges which might cut the packing. Scratches or burrs could cause packing box leakage or damage to the new packing. If the surface condition cannot be improved by light sanding, replace the damaged parts by following the appropriate steps in the Trim Maintenance procedure. 0. Remove the covering protecting the valve body cavity and install a new bonnet gasket (key 0, figure 3 through 5), making sure the gasket seating surfaces are clean and smooth. Then slide the bonnet over the stem and onto the stud bolts (key 5, figure 3, 4, or 5) or onto the valve body cavity if cap screws (not shown) will be used instead. Note Proper performance of the bolting procedures in step compresses the spiral wound gasket (key 2, figure 3 through 5) or load ring (key 26, figure 4) enough to both load and seal the seat ring gasket (key 3, figure 3, 4, or 5). It also compresses the outer edge of the bonnet gasket (key 0, figure 3 through 5) enough to seal the body to bonnet joint. The proper bolting procedures in step include but are not limited to ensuring that bolting threads are clean, and evenly tightening the cap screws, or the nuts onto the studs, in a crisscross pattern. Because of the boltup characteristics of spiral wound gaskets, tightening one cap screw or nut may loosen an adjacent cap screw or nut. Repeat the crisscross tightening pattern several times until each cap screw or nut is tight and the body to bonnet seal is made. When the operating temperature has been reached, perform this torquing procedure once again.. Install bolting, using proper bolting procedures during tightening so that the body to bonnet joint will withstand test pressures and application service conditions. The bolt torques in table 3 may be used as guidelines. 2. Install new packing and the metal packing box parts according to the appropriate arrangement in figure 3, 5, or 7. For split ring packing, alternate the positions of the splits to avoid creating a leak path. Place a smooth edged pipe over the valve stem and gently tap each soft packing part into the packing box, being sure that air is not trapped between adjacent soft parts. 3. Slide the packing follower, upper wiper, and packing flange (keys 3, 2, and 3, figure 8) into position. Lubricate the packing flange studs (key 4, figure 8) and the faces of the packing flange nuts (key 5, figure 8). Install the packing flange nuts. 4. For spring loaded PTFE V ring packing, tighten the packing flange nuts until the shoulder on the packing follower (key 3, figure 8) contacts the bonnet. For ENVIRO SEAL or HIGH SEAL live loaded packing, refer to the note at the beginning of the Maintenance section. For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 4. Then, loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 4. For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nuts reaches the minimum recommended torque shown in table 4. Then, tighten the remaining flange nuts until the packing flange is level and at a 90 degree angle to the valve stem. 0

Instruction Manual ES Valve 5. Mount the actuator on the valve assembly and reconnect the actuator and valve stem according to the procedure in the appropriate actuator instruction manual. Trim Maintenance WARNING Refer to the WARNING at the beginning of the Maintenance section in this instruction manual. CAUTION In the following applicable procedures, to avoid damaging parts, do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat areas on the stem where it extends out of the top of the bellows shroud. Except where indicated, key numbers in this section are referenced in figure 3 for standard NPS /2 through 6 constructions, figure 4 for NPS 8 ES valves, figure 5 for Whisper Trim III cage detail, and figure 6 for WhisperFlo trim. Disassembly. Remove the actuator and the bonnet according to steps through 6 of the Replacing Packing procedure of the Maintenance section. Table 4. Recommended Torque for Packing Flange Nuts (Not for Spring Loaded Packing) GRAPHITE TYPE PACKING PTFE TYPE PACKING VALVE STEM DIAMETER PRESS URE Minimum Torque Maximum Torque Minimum Torque Maximum Torque RATING mm Inches N m Lbf in N m Lbf in N m Lbf in N m Lbf in CL25, 50 3 24 5 48 2 3 24 9.5 3/8 CL250, 300 4 36 7 60 2 8 3 30 CL600 5 48 8 72 3 24 4 36 CL25, 50 5 48 8 72 3 24 4 36 2.7 /2 CL250, 300 7 60 0 84 3 30 5 42 CL600 0 84 4 20 5 42 7 60 CL25, 50 96 6 44 5 48 8 72 9. 3/4 CL250, 300 4 20 20 80 7 60 0 90 CL600 20 80 30 264 0 90 5 32 25.4 CL300 24 26 37 324 2 08 6 44 CL600 34 300 50 444 6 44 24 26 3.8 /4 CL300 33 288 49 432 6 44 24 26 CL600 45 396 66 588 22 92 33 288

ES Valve Instruction Manual WARNING To avoid personal injury due to leaking fluid, avoid damaging gasket sealing surfaces. The surface finish of the valve stem (key 7) is critical for making a good packing seal. The inside surface of the cage or cage/baffle assembly (key 3), or cage retainer (key 3), is critical for smooth operation of the valve plug. The seating surfaces of the valve plug (key 2) and seat ring (key 9) are critical for proper shutoff. Unless inspection reveals otherwise, assume all these parts are in good condition and protect them accordingly. 2. Packing parts can be removed if desired. Replace these parts as described in the Replacing Packing procedure. Remove the load ring (key 26) from an NPS 8 ES valve, or the cage adaptor (key 4) from any restricted trim valve, and wrap it for protection. 3. Lift the valve plug and stem assembly out of the valve and set it on a protective surface. If the valve plug is to be reused, protect the valve plug seating surface to prevent scratches. On an NPS 6 ES valve with Whisper Trim III cage or WhisperFlo trim, also remove the bonnet spacer (key 32) and bonnet gasket (key 0) on top of the spacer. Then on any construction with a cage retainer (key 3), remove the cage retainer and its associated gaskets. A Whisper Trim III and WhisperFlo trim cage retainer has two 3/8 inch 6 UNC tappings in which screws or bolts can be installed for lifting. 4. Remove the cage or cage/baffle assembly (key 3), the associated gaskets (keys 0,, and 2), and shim (key 5 for the ES valve, key 27 for the EAS valve). If the cage is stuck in the valve body, use a rubber mallet to strike the exposed portion of the cage at several points around its circumference. 5. Remove the seat ring or liner (key 9) or disk seat (key 22), seat ring gasket (key 3), and the seat ring adaptor (key 5) and adaptor gasket (key 4) where used in a restricted trim seat ring construction. PTFE seat constructions use a disk (key 23) sandwiched between the disk seat and disk retainer (key 2). 6. Inspect parts for wear or damage which would prevent proper operation of the valve. Replace or repair trim parts according to the following procedure for lapping metal seats or other valve plug maintenance procedures as appropriate. Table 5. Valve Stem Connection Torque and Pin Replacement VALVE STEM CONNECTION (VSC) BOLT TORQUE, MINIMUM TO MAXIMUM HOLE SIZE mm Inches N m Lbf ft mm Inch 9.5 2.7 9. 25.4 3.8 3/8 /2 3/4 /4 40 47 8 5 237 339 420 48 827 908 25 35 60 85 75 250 30 355 60 670 2.4 2.46 3.20 3.25 4.80 4.88 6.38 6.45 6.38 6.45 0.095 0.097 0.26 0.28 0.89 0.92 0.25 0.254 0.25 0.254 Table 6. Standard Material Designations Standard Designation CoCr A Hardfacing Alloy R30006 S7400 SST S3600 SST S4000, S4600, CA5 WCC Carbon Steel Casting Common Name or Trade Name CoCr A Alloy 6 Casting 7 4PH Stainless Steel 36 Stainless Steel 3Cr 400 Series SST WCC CAUTION To avoid damaging the ENVIRO SEAL bellows seal bonnet assembly, do not attempt to lap the metal seating surfaces. The design of the assembly prevents rotation of the stem and any forced lapping rotation will damage internal components of the ENVIRO SEAL bellows seal bonnet. 2

Instruction Manual ES Valve Lapping Metal Seats A certain amount of leakage should be expected with metal to metal seating in any valve body. If the leakage becomes excessive, however, the condition of the seating surfaces of the valve plug and seat ring can be improved by lapping. (Deep nicks should be machined out rather than ground out.) Use a good quality lapping compound of a mixture of 280 to 600 grit. Apply the compound to the bottom of the valve plug. Assemble the valve to the extent that the cage and the cage retainer and bonnet spacer (if used) are in place and the bonnet is bolted to the valve body. A simple handle can be made from a piece of strap iron locked to the valve plug stem with nuts. Rotate the handle alternately in each direction to lap the seats. After lapping, remove the bonnet and clean the seat surfaces. Completely assemble as described in the assembly portion of the trim maintenance procedure and test the valve for shutoff. Repeat the lapping procedure if leakage is still excessive. CAUTION To avoid weakening the stem or adaptor that may cause failure in service, never reuse an old stem or adaptor with a new valve plug. Using an old stem or adaptor with a new plug requires drilling a new pin hole in the stem (or adaptor in case an ENVIRO SEAL bellows seal bonnet is being used), which will weaken the stem. However, a used valve plug may be reused with a new stem or adaptor. Valve Plug Maintenance Except where indicated, key numbers are referenced in figure 3 for NPS /2 through 6 constructions, figure 4 for NPS 8 ES valves, figure 5 for Whisper Trim III cage detail, and figure 6 for WhisperFlo trim.. Remove the valve plug (key 2) according to the disassembly portion of the trim maintenance procedure. 2. To replace the valve stem (key 7), drive out the pin (key 8). Unscrew the valve plug from the stem or adaptor. 3. To replace the adaptor (key 24, figure 8) on ENVIRO SEAL bellows seal bonnets, place the plug stem assembly and valve plug in a soft jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a seating surface. Drive out or drill out the pin (key 36, figure 8). Reverse the plug stem assembly in the soft jaw chuck or vise. Grip the flat areas on the valve stem just below the threads for the actuator/stem connection. Unscrew the valve plug/adaptor assembly (key 24, figure 8) from the valve stem assembly (key 20, figure 8). 4. Screw the stem or adaptor into the valve plug. Tighten to the torque value given in table 5. Refer to table 5 to select the proper hole size. Drill through the stem or adaptor, using the hole in the valve plug as a guide. Remove any chips or burrs and drive in a new pin to lock the assembly. 5. For ENVIRO SEAL bellows seal bonnets, grip the flats of the stem extending out of the top of the bellows shroud with a soft jaw chuck or other type of vise. Screw the valve plug/adaptor assembly onto the valve stem. Tighten as necessary to align the pin hole in the stem with one of the holes in the adaptor. Secure the adaptor to the stem with a new pin. Assembly Except where indicated, key numbers are referenced in figure 3 for standard NPS /2 through 6 constructions, figure 4 for NPS 8 ES valves, figure 5 for Whisper Trim III cage detail, and figure 6 for WhisperFlo trim.. With a restricted trim seat ring construction, install the adaptor gasket (key 4) and seat ring adaptor (key 5). 2. Install the seat ring gasket (key 3), seat ring or liner (key 9), or disk seat (key 22). With a PTFE seat construction, install the disk and disk retainer (keys 2 and 23). 3. Install the cage or cage/baffle assembly (key 3). Any rotational orientation of the cage or assembly with respect to the valve is acceptable. A Whisper Trim III cage designated by level A3, B3, or C3 may be installed with either end 3

ES Valve Instruction Manual up. The level D3 cage/baffle assembly, however, must be installed with the hole pattern end next to the seat ring. If a cage retainer (key 3) is to be used, place it on top of the cage. 4. Slide the valve plug (key 2) and stem assembly, or valve plug and ENVIRO SEAL bellows seal assembly, into the cage. 5. Place the gaskets (key 0, or keys, 2 and 4, if used) and the shim (key 27 or key 5) on top of the cage or cage retainer. If there is a cage adaptor (key 4) or a bonnet spacer (key 32), set it on the cage or cage retainer gaskets and place another flat sheet gasket (key 0) on top of the adaptor or spacer. If there is only a cage retainer, place another flat sheet gasket on the retainer. 6. With an NPS 8 ES valve, install the load ring (key 26). CAUTION To avoid damaging packing with the valve stem threads, use care when installing the bonnet if the packing was not removed from the bonnet. Table 7. Recommended Torque for ENVIRO SEAL Bellows Seal Packing Flange Nuts VALVE SIZE VALVE STEM DIAMETER THROUGH PACKING MINIMUM TORQUE MAXIMUM TORQUE NPS Inch N m Lbf in N m Lbf in /2 2 /2 3 24 5 48 3 4 7 60 0 84 7. Mount the bonnet on the valve and complete assembly according to steps 0 through 4 of the Replacing Packing procedure, omitting steps and 2 if new packing is not being installed, and being sure to observe the note prior to step. ENVIRO SEAL Bellows Seal and Bonnet Replacing a Plain or Extension Bonnet with an ENVIRO SEAL Bellows Seal (Stem/Bellows Assembly) and Bonnet. Remove the actuator and bonnet according to steps through 6 of the Replacing Packing procedure of the Maintenance section. 2. With care, remove the valve plug and stem assembly from the valve body. If necessary, lift out the cage, also. CAUTION To prevent possible product damage, cover the opening in the valve in the following procedure to protect the sealing surfaces and to prevent foreign material from getting into the valve body cavity. 3. Remove and discard the existing bonnet gasket. Cover the valve body opening to protect sealing surfaces and to prevent foreign material from entering the valve body cavity. Note The ENVIRO SEAL stem/bellows assembly for easy e valves is available only with a threaded and drilled plug/adaptor/stem connection. The existing valve plug can be reused with the new stem/bellows assembly or a new plug can be installed. 4

Instruction Manual ES Valve 4. Inspect the existing valve plug. If the plug is in good condition, it can be reused with the new ENVIRO SEAL stem/bellows assembly. To remove the existing valve plug from the stem, first, place the existing plug stem assembly and valve plug in a soft jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a seating surface. Drive out or drill out the pin (key 8). 5. Then, reverse the plug stem assembly in the soft jaw chuck or vise. Grip the valve stem in an appropriate place and unscrew the existing plug from the valve stem. CAUTION When installing a valve plug on the ENVIRO SEAL stem/bellows assembly, the valve stem must not be rotated. Damage to the bellows may result. To avoid damaging parts, do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat areas on the stem where it extends out of the top of the bellows shroud. Note The ENVIRO SEAL stem/bellows assembly has a one piece stem. 6. To attach the valve plug to the stem of the new ENVIRO SEAL stem/bellows assembly, it is necessary to first attach the plug to the adaptor (key 24). Locate the adaptor. Notice that a hole has not been drilled in the threads where the plug screws onto the adaptor. Secure the valve plug in a soft jaw chuck or other type of vise. Do not grip the plug on any seating surface. Position the plug in the chuck or vise for easy threading of the adaptor. Thread the adaptor into the valve plug and tighten to the appropriate torque value. 7. Select the proper size of drill bit and drill through the adaptor using the hole in the valve plug as a guide. Remove any metal chips or burrs and drive in a new pin to lock the plug/adaptor assembly together. 8. Attach the plug/adaptor assembly to the ENVIRO SEAL stem/bellows assembly by first securing the stem/bellows assembly in a soft jaw chuck or other type of vise so that the jaws of the chuck or vise grip the flats of the stem extending out of the top of the bellows shroud. Screw the valve plug/adaptor assembly onto the valve stem. Tighten as necessary to align the pin hole in the stem with one of the holes in the adaptor. Secure the adaptor to the stem with a new pin. 9. Inspect the seat ring (key 9) and soft seat parts (keys 2, 22, and 23). Replace, if necessary. 0. Place a new gasket (key 0) into the valve body in place of the bonnet gasket. Install the new stem/bellows assembly with valve plug/adaptor by placing it into the valve body on top of the new bellows gasket.. Place a new gasket (key 22) over the stem/bellows assembly. Place the new ENVIRO SEAL bonnet over the stem/bellows assembly. Note Stud(s) and nut(s) should be installed such that the manufacturer's trademark and material grade marking is visible, allowing easy comparison to the materials selected and documented in the Emerson/Fisher serial card provided with this product. WARNING Personal injury or damage to equipment could occur if improper stud and nut materials or parts are used. Do not operate or assemble this product with stud(s) and nut(s) that are not approved by Emerson/Fisher engineering and/or listed on the serial card provided with this product. Use of unapproved materials and parts could lead to stresses exceeding the design or code limits intended for this particular service. Install studs with the material grade and manufacturer's identification 5

ES Valve Instruction Manual mark visible. Contact your Emerson representative immediately if a discrepancy between actual parts and approved parts is suspected. 2. Properly lubricate the bonnet stud bolts. Install and tighten the bonnet hex nuts to the proper torque. 3. Install new packing and the metal packing box parts according to the appropriate arrangement in figure 3. 4. Install the packing flange. Properly lubricate the packing flange stud bolts and the faces of the packing flange nuts. For ENVIRO SEAL or HIGH SEAL live loaded packing, refer to the note at the beginning of the Maintenance section. For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 7. Then, loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 7. For other packing types, tighten the packing flange nuts alternately in small equal increments until one of the nuts reaches the minimum recommended torque shown in table 7. Then, tighten the remaining flange nuts until the packing flange is level and at a 90 degree angle to the valve stem. 5. Install travel indicator parts, stem locknuts, and mount the actuator on the valve body according to the procedure in the appropriate actuator instruction manual. Replacement of an Installed ENVIRO SEAL Bellows Seal (Stem/Bellows Assembly). Remove the actuator and bonnet according to steps through 6 of the Replacing Packing procedure of the Maintenance section. CAUTION To prevent possible product damage, cover the opening in the valve in the following procedure to protect the sealing surfaces and to prevent foreign material from getting into the valve body cavity. 2. With care, remove the ENVIRO SEAL stem/bellows assembly. If necessary, lift out the cage, also. Remove and discard the existing bonnet gasket and bellows gasket. Cover the valve body opening to protect sealing surfaces and to prevent foreign material from entering the valve body cavity. Note The ENVIRO SEAL stem/bellows assembly for easy e valves is available only with a threaded and drilled plug/adaptor/stem connection. The existing valve plug can be reused with the new stem/bellows assembly or a new plug can be installed. 3. Inspect the existing valve plug. If the plug is in good condition, it can be reused with the new stem/bellows assembly. CAUTION When removing/installing a valve plug on the ENVIRO SEAL stem/bellows assembly, the valve stem must not be rotated. Damage to the bellows may result. To avoid damaging parts, do not grip the bellows shroud or other parts of the stem/bellows assembly. Grip only the flat areas on the stem where it extends out of the top of the bellows shroud. 6

Instruction Manual ES Valve Note The ENVIRO SEAL stem/bellows assembly has a one piece stem. 4. To remove the existing valve plug from the stem, first, place the existing plug stem assembly and valve plug in a soft jaw chuck or other type of vise so that the jaws grip a portion of the valve plug that is not a seating surface. Drive out or drill out the pin. 5. Then, reverse the plug stem assembly in the soft jaw chuck or vise. Grip the flat areas on the valve stem just below the threads for the actuator/stem connection. Unscrew the existing plug from the valve stem. 6. To attach either the existing valve plug or a new one to the stem of the new ENVIRO SEAL stem/bellows assembly, it is necessary to first attach the plug to the adaptor. Locate the adaptor. Notice that a hole has not been drilled in the threads where the plug screws onto the adaptor. Secure the valve plug in a soft jaw chuck or other type of vise. Do not grip the plug on any seating surface. Position the plug in the chuck or vise for easy threading of the adaptor. Thread the adaptor into the valve plug and tighten to the appropriate torque value. 7. Complete the installation by following steps 7 through 9 and steps 2 through 5 of the ENVIRO SEAL Bellows Seal and Bonnet installation instructions given above. Purging the ENVIRO SEAL Bellows Seal Bonnet The ENVIRO SEAL bellows seal bonnet has been designed so that it can be purged or leak tested. Refer to figure 8 for an illustration of an ENVIRO SEAL bellows seal bonnet, and perform the following steps for purging or leak testing.. Remove the two diametrically opposed pipe plugs (key 6). 2. Connect a purging fluid to one of the pipe plug connections. 3. Install appropriate piping or tubing in the other pipe plug connection to pipe away the purging fluid or to make a connection to an analyzer for leak testing. 4. When purging or leak testing has been completed, remove the piping or tubing and reinstall the pipe plugs (key 6). Parts Ordering Each body bonnet assembly is assigned a serial number which can be found on the valve. This same number also appears on the actuator nameplate when the valve is shipped from the factory as part of a control valve assembly. Refer to the serial number when contacting your Emerson sales office or Local Business Partner for technical assistance. When ordering replacement parts, refer to the serial number and to the eleven character part number for each part required from the following parts kit or parts list information. Refer to table 6 for standard and common material designations. WARNING Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Automation Solutions should not, under any circumstances, be used in any Fisher valve, because they may void your warranty, might adversely affect the performance of the valve, and could cause personal injury and property damage. Parts Kits Note Kits do not apply to alloy C (N0276 and CW2M), Alloy 20 (N08020 and CN7M), or alloy 400 (N04400 and M35 ) trims. 7

ES Valve Instruction Manual Gasket Kits Gasket Kits (includes keys 0,, 2, 3, and 5); plus 4 and 20 on Some Restricted Capacity Valves DESCRIPTION Standard Trim Cage Whisper Trim I Cage Whisper Trim III Cage WhisperFlo Cage -98 to 593 C (-325 to 00 F) -98 to 593 C (-325 to 00 F) Full Capacity Valves Part Number Part Number NPS /2, 3/4,, and /4 (NPS EAS) NPS /2 (NPS 2 EAS) NPS 2 NPS 2 /2 (NPS 3 EAS) NPS 3 (NPS 4 EAS) NPS 4 (NPS 6 EAS) NPS 6 NPS 8 Restricted Capacity Valves w/ Metal Seating NPS /2 x (NPS 2 x EAS) NPS 2 x NPS 2 /2 x /2 (NPS 3 x /2 EAS) NPS 3 x 2 (NPS 4 x 2 EAS) NPS 4 x 2 /2 (NPS 6 x 2 /2 EAS) RGASKETX62 RGASKETX72 RGASKETX82 RGASKETX92 RGASKETX202 RGASKETX22 RGASKETX222 RGASKETX232 RGASKETX242 RGASKETX252 RGASKETX262 RGASKETX272 RGASKETX282 RGASKETX422 RGASKETX432 RGASKETX442 RGASKETX452 RGASKETX462 RGASKETX472 RGASKETX482 0A3265X52 - - - - - - - - - - - - - - - Packing Kits Standard Packing Repair Kits (Non Live Loaded) REPAIR KIT MATERIAL 9.5 (3/8) 54 (2 /8) STEM DIAMETER, mm (INCH) YOKE BOSS DIAMETER, mm (INCH) 2.7 (/2) 7 (2 3/6) 9. (3/4) 90 (3 9/6) Part Number 25.4 () 27 (5) 3.8 (-/4) 27 (5, 5H) PTFE (Contains keys 6, 8, 0,, and 2) RPACKX0002 RPACKX00022 RPACKX00032 RPACKX00342 RPACKX00352 Double PTFE (Contains keys 6, 8,, and 2) RPACKX00042 RPACKX00052 RPACKX00062 RPACKX00362 RPACKX00372 PTFE/Composition (Contains keys 7, 8,, and 2) RPACKX00072 RPACKX00082 RPACKX00092 - - - - - - Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], 8, and ) RPACKX0002 RPACKX002 RPACKX0022 - - - - - - Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], and ) - - - - - - - - - RPACKX00532 RPACKX00542 Single Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring]) RPACKX0032 RPACKX0042 RPACKX0052 - - - - - - Double Graphite Ribbon/Filament (Contains keys 7 [ribbon ring], 7 [filament ring], 8, and ) RPACKX0062 RPACKX0072 RPACKX0082 - - - - - - ENVIRO SEAL Packing Retrofit Kits Retrofit kits include parts to convert valves with existing standard bonnets to the ENVIRO SEAL packing box construction. Refer to figure 0 for key numbers for PTFE packing, to figure for key numbers for Graphite ULF packing, and to figure 2 for key numbers for duplex packing. PTFE kits include keys 200, 20, 2, 22, 24, 25, 27, 28, tag, and cable tie. Graphite ULF kits include keys 200, 20, 207, 208, 209, 20, 2, 22, 24, 26, 27, tag, and cable tie. Duplex kits include keys 200, 20, 207, 209, 2, 22, 24, 25, 26, 27, tag, and cable tie. Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and design specifications may adversely alter the performance of this packing kit. 8

Instruction Manual ES Valve For part numbers of individual components in the ENVIRO SEAL packing kits, refer to instruction manual ENVIRO SEAL Packing System for Sliding Stem Valves, D0642X02. ENVIRO SEAL Packing Retrofit Kits PACKING MATERIAL 9.5 (3/8) 54 (2 /8) 2.7 (/2) 7 (2 3/6) STEM DIAMETER, mm (INCH) YOKE BOSS DIAMETER, mm (INCH) 9. (3/4) 90 (3 9/6) Part Number 25.4 () 27 (5) 3.8 ( /4) 27 (5, 5H) Double PTFE RPACKXRT02 RPACKXRT022 RPACKXRT032 RPACKXRT042 RPACKXRT052 Graphite ULF RPACKXRT262 RPACKXRT272 RPACKXRT282 RPACKXRT292 RPACKXRT302 Duplex RPACKXRT22 RPACKXRT222 RPACKXRT232 RPACKXRT242 RPACKXRT252 ENVIRO SEAL Packing Repair Kits Repair kits include parts to replace the soft packing materials in valves that already have ENVIRO SEAL packing arrangements installed or in valves that have been upgraded with ENVIRO SEAL retrofit kits. Refer to figure 0 for key numbers for PTFE packing, to figure for key numbers for Graphite ULF packing, and to figure 2 for key numbers for duplex packing. PTFE repair kits include keys 24, 25, and 28. Graphite ULF repair kits include keys 207, 208, 209, 20, and 24. Duplex repair kits include keys 207, 209, 24, and 25. Stems and packing box constructions that do not meet Fisher stem finish specifications, dimensional tolerances, and design specifications may adversely alter the performance of this packing kit. For part numbers of individual components in the ENVIRO SEAL packing kits, refer to instruction manual ENVIRO SEAL Packing System for Sliding Stem Valves, D0642X02. ENVIRO SEAL Packing Repair Kits PACKING MATERIAL 9.5 (3/8) 54 (2 /8) STEM DIAMETER, mm (INCH) YOKE BOSS DIAMETER, mm (INCH) 2.7 (/2) 7 (2 3/6) 9. (3/4) 90 (3 9/6) Part Number 25.4 () 27 (5) 3.8 ( /4) 27 (5, 5H) Double PTFE (contains keys 24, 25, & 28) RPACKX0092 RPACKX00202 RPACKX0022 RPACKX00222 RPACKX00232 Graphite ULF (contains keys 207, 208, 209, 20, and 24) RPACKX00592 RPACKX00602 RPACKX0062 RPACKX00622 RPACKX00632 Duplex (contains keys 207, 209, 24, and 25) RPACKX00292 RPACKX00302 RPACKX0032 RPACKX00322 RPACKX00332 9

ES Valve Instruction Manual easy-e Low-e Bonnet Repair Kits Kit consists of plain bonnet, Graphite / Inconel gasket set, ENVIRO-SEAL packing retro-fit kit, packing flange, packing flange studs and nuts. New stem is not included. Bonnet Material Packing Type Valve Size, NPS Stem Size Part Number 0.5-.25 3/8 RLEPBNTX02.5 3/8 RLEPBNTX022 2 /2 RLEPBNTX032 ENVIRO-SEAL PTFE 2.5 /2 RLEPBNTX042 3 /2 RLEPBNTX052 4 /2 RLEPBNTX062 6 3/4 RLEPBNTX072 WCC () 0.5-.25 3/8 RLEPBNTX52.5 3/8 RLEPBNTX62 2 /2 RLEPBNTX72 ENVIRO-SEAL Graphite ULF 2.5 /2 RLEPBNTX82 3 /2 RLEPBNTX92 4 /2 RLEPBNTX202 6 3/4 RLEPBNTX22 0.5-.25 3/8 RLEPBNTX082.5 3/8 RLEPBNTX092 ENVIRO-SEAL PTFE 2 /2 RLEPBNTX02 2.5 /2 RLEPBNTX2 3 /2 RLEPBNTX22 4 /2 RLEPBNTX32 SST () 0.5-.25 3/8 RLEPBNTX222.5 3/8 RLEPBNTX232 ENVIRO-SEAL Graphite ULF 2 /2 RLEPBNTX242 2.5 /2 RLEPBNTX252 3 /2 RLEPBNTX262 4 /2 RLEPBNTX272 0.5-.25 3/8 RLEPBNTX292.5 3/8 RLEPBNTX302 2 /2 RLEPBNTX322 WCC ENVIRO-SEAL Duplex 2.5 /2 RLEPBNTX332 3 /2 RLEPBNTX342 4 /2 RLEPBNTX352 6 3/4 RLEPBNTX362 0.5-.25 3/8 RLEPBNTX372.5 3/8 RLEPBNTX392 SST ENVIRO-SEAL Duplex 2 /2 RLEPBNTX42 2.5 /2 RLEPBNTX422 3 /2 RLEPBNTX432 4 3/4 RLEPBNTX442. Compliant with NACE MR075-2003 and prior, NACE MR075 / ISO 556 (all revisions), and NACE MR003 (all revisions). 20

Instruction Manual ES Valve Parts List Key Description Note Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson sales office or Local Business Partner. Bonnet (figures 3 2) Key Description Bonnet/ENVIRO SEAL bellows seal bonnet If you need a bonnet or an ENVIRO SEAL bellows seal bonnet as a replacement part, order by valve size and stem diameter, serial number, and desired material. 2 Extension Bonnet Baffle 3 Packing Flange 3 ENVIRO SEAL bellows seal packing flange 4 Packing Flange Stud 4 ENVIRO SEAL bellows seal stud bolt 5 Packing Flange Nut 5 ENVIRO SEAL bellows seal hex nut 6* Packing set, PTFE 6* ENVIRO SEAL bellows seal packing set 7* Packing ring, PTFE composition 7* ENVIRO SEAL bellows seal packing ring 8 Spring 8 Lantern ring 8 ENVIRO SEAL bellows seal spring 8 ENVIRO SEAL bellows seal spacer 0 Special washer * Packing Box Ring 2* Upper Wiper, felt 2* ENVIRO SEAL bellows seal upper wiper 3* Packing Follower 3* ENVIRO SEAL bellows seal bushing 3* ENVIRO SEAL bellows seal bushing/liner 4 Pipe Plug for /4 NPT Tapping in Packing Box 4 Lubricator 4 Lubricator/Isolating Valve 5 Yoke Locknut 5 ENVIRO SEAL bellows seal Locknut 6 Pipe Plug for /2 NPT Tapped Extension Bonnets 6 ENVIRO SEAL bellows seal pipe plug 20* ENVIRO SEAL bellows seal stem/bellows assembly 22* ENVIRO SEAL bellows seal bonnet gasket 24 ENVIRO SEAL bellows seal adaptor 25 Cap Screw for 27 mm (5 inch) yoke boss 26 Hex Nut for 27 mm (5 inch) Yoke Boss 27 Pipe Nipple for Lubricator/Isolating Valve 28 ENVIRO SEAL bellows seal nameplate, warning 29 ENVIRO SEAL bellows seal drive screw 34 Lubricant, anti seize 36 ENVIRO SEAL bellows seal pin 37 ENVIRO SEAL bellows seal warning tag 38 ENVIRO SEAL bellows seal tie 39 ENVIRO SEAL bellows seal thrust ring *Recommended spare parts 2

ES Valve Instruction Manual Figure 8. Typical Bonnets 30A9425 A DETAIL OF 5 INCH (27 mm) YOKE BOSS ACTUATOR BOLTING E020 PLAIN BONNET APPLY LUB CU39 D STYLE OR 2 EXTENSION BONNET 42B3947 A ENVIRO SEAL BELLOWS SEAL BONNET 22

Instruction Manual ES Valve Figure 9. Typical HIGH SEAL Graphite ULF Packing System Figure. Typical ENVIRO SEAL Packing System with Graphite ULF Packing STUD (KEY 200) HEX NUT (KEY 22) PACKING FLANGE (KEY 20) PACKING RING (KEY 209) SPRING PACK ASSEMBLY (KEY 27) GUIDE BUSHING (KEY 207) PACKING WASHERS (KEY 24) PACKING RING (KEY 20) PACKING BOX RING (KEY 2) GUIDE BUSHING (KEY 208). FIND NUMBER 29 NOT REQUIRED WITH 3/8 INCH STEM 39B453 A 39B462/A Figure 0. Typical ENVIRO SEAL Packing System with PTFE Packing Figure 2. Typical ENVIRO SEAL Packing System with Duplex Packing HEX NUT (KEY 22) STUD (KEY 200) 200 23 PACKING FLANGE (KEY 20) SPRING PACK ASSEMBLY (KEY 27) 22 20 LANTERN RINGS (KEY 26) 27 ANTI EXTRUSION WASHERS 25 207 PACKING SET (KEY 25) 26 207 207 LOWER WIPER (KEY 28) A6297 PACKING BOX RING (KEY 2) 209 2 24 207 A6722 23

ES Valve Instruction Manual Valve Body (figures 3 5) Key Description Valve Body If you need a valve body as a replacement part, order by valve size, serial number, and desired material. 2* Valve plug 3* Cage 4 Trim adaptor 5 Trim adaptor 7* Valve plug stem 8* Pin 9* Liner 9* Seat Ring 0* Bonnet Gasket * Cage Gasket 2* Spiral Wound Gasket 3* Seat Ring or Liner Gasket 4* Adaptor Gasket Key Description 22* Disk Seat 23* Disk 26 Load Ring 27* Shim 3* Whisper Trim III Cage Retainer for Levels A3, B3 & C3 (NPS 6 ES only) 3* Whisper Trim III Cage retainer & Baffle Ass'y for Level D3 (NPS 6 ES only) 32 Whisper Trim III Bonnet Spacer 5* Shim 53 Nameplate 54 Wire 5 Cap Screw 5 Stud 6 Nut 7 Pipe Plug 8 Flow Direction Arrow 9 Drive Screw 20* Adaptor Gasket 2* Seat Disk Retainer 24 *Recommended spare parts

Instruction Manual ES Valve Figure 3. NPS /2 through 6 Fisher ES and EAS Valves FLOW DIRECTION CAVITROL TRIM STD TRIM WHISPER TRIM 30A9543 D FLOW DIRECTION STD TRIM CAVITROL TRIM DETAIL OF COMPOSITION (PTFE) SEAT CU9974 E 25

ES Valve Instruction Manual Figure 4. NPS 8 Fisher ES Valve with Optional Drain Plug FLOW DIRECTION CAVITROL TRIM STD TRIM WHISPER TRIM METAL SEAT 40A3288 C B884 COMPOSITION (PTFE) SEAT 26

Instruction Manual ES Valve Figure 5. Whisper Trim III Cage Detail with Optional Drain Plug E37 52A3326 D 27

ES Valve Instruction Manual Figure 6. Fisher ES Valve Assembly with WhisperFlo Cage with Optional Drain Plug 9 8 6 7 32 0 5 0 3 53 2 8 9 3 3 2 7 E38 28

Instruction Manual ES Valve Gaskets and Shims Parts Kit (9) Valve Size, NPS ET /2, 3/4, or /4 EAT Standard Trim Cage Whisper Trim I Cage Cavitrol III - Stage Cage -98 to 593 C (-325 to 00 F) Part Number Cavitrol III - 2 Stage Cage Whisper Trim III Cage WhisperFlo Cage VALVE SIZE, NPS ET EAT Standard Trim Cage Whisper Trim I Cage Cavitrol III - Stage Cage -98 to 593 C (-325 to 00 F) Part Number Cavitrol III - 2 Stage Cage Whisper Trim III Cage WhisperFlo Cage RGASKETX62 ()(2) RGASKETX422 (3) 3 4 RGASKETX202 ()(2) RGASKETX462 (3) /2 2 RGASKETX72 ()(2) RGASKETX432 (3) 3 x 2 4 x 2 RGASKETX272 ()(4) - - - /2 x 2 x RGASKETX242 ()(5) - - - 4 6 RGASKETX22 ()(2) RGASKETX472 (3) 2 RGASKETX82 (6) RGASKETX442 (3) 4 x 2 /2 6 x 2 /2 RGASKETX282 ()(4) - - - 2 x RGASKETX252 (4) - - - 6 RGASKETX222 (6) RGASKETX482 (6) 2 /2 3 RGASKETX92 ()(2) RGASKETX452 (3) 8 RGASKETX232 (7) 2 /2 x /2 3 x /2 RGASKETX262 ()(4) - - -. Set number good for both ES and EAS valve 2. Kit includes key 0, 2, 3. 27 or 5 3. Kit includes key 0, qty 2; 2; 3; 5 4. Kit includes key 0,, 2, 3, 4, 27 or 5 5. Kit includes key 0,, 2, 3, 20, 27 or 5 6. Kit includes key 0, 2, 3, 5 7. Kit includes key 0 and 3 8. Kit includes key 0, qty 2; and 3 9. See table below for gasket descriptions Gasket Descriptions KEY NUMBER DESCRIPTION MATERIAL FGM -98 to 593 C (-325 to 00 F) 0 Bonnet Gasket Cage Gasket 3 Seat Ring or Liner Gasket Graphite/S3600 4 or 20 Adapter Gasket 2 Spiral Wound Gasket N06600/Graphite 27 or 5 Shim S3600 29

ES Valve Instruction Manual 30

Instruction Manual ES Valve 3

ES Valve Instruction Manual Neither Emerson, Emerson Automation Solutions, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Fisher, easy-e, ENVIRO-SEAL, WhisperFlo, and Whisper Trim are marks owned by one of the companies in the Emerson Automation Solutions business unit of Emerson Electric Co. Emerson Automation Solutions, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners. The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without notice. Emerson Automation Solutions Marshalltown, Iowa 5058 USA Sorocaba, 8087 Brazil Cernay 68700 France Dubai, United Arab Emirates Singapore 2846 Singapore www.fisher.com 32 973, 207 Fisher Controls International LLC. All rights reserved.