International Motors/Gearmotors/Controls

International Motors/Gearmotors/Controls

AC INTENATIONAL PODUCTS INTODUCTION The metric products listed in this section have been designed with international design standards in mind. The 230 volt, 50 Hz windings can be operated satisfactorily on any nominal system voltage between 220 and 240 volts to accommodate almost all international power supply requirements. Splashproof terminal boxes are standard on most AC products. Mounting and shaft configurations designed for common metric sizes provide convenient interfacing capability. CONSTUCTION ECOGNITION Most Bodine products are third party approved with respect to construction. Metric motors and gearmotors are designed to meet most requirements of BSI, IEC, and VDE. Their nameplates bear an IEC 34-1 designation. Motors, gearmotors and controls are recognized by U.L., Inc. and are registered in U.L. Construction recognition file No. E47177 and E44529. Many stock products are also CSA certified and appear in CSA File No. L2797 and L26397. Bodine metric motors and gearmotors also meet CE standards. See page 4 for more information. AC CONNECTIONS 074 10021 074 10132 074 10279 230 V 460 V ED BLACK BLUE WHITE GN-YEL T. (GD) LINE LINE WHITE BLUE ED BLACK GEEN/YELLOW LINE LINE T-1 BLACK T-6 ED/YELLOW T-2 BLUE T-4 BLACK/YELLOW T-3 ED T-5 BLUE/YELLOW LINE LINE LINE BLACK T-1 BLUE T-2 ED T-3 BLACK/YELLOW T-4 BLUE/YELLOW T-5 ED/YELLOW T-6 GEEN/YELLOW GEEN/YELLOW To reverse transpose the black and white leads. To reverse transpose the black and white leads. 074 10279-To reverse transpose any leads or combinations K-2 MOTO 2.8 WATTS (3.8 MILLI. HP) For more information see page 14 Output Input adial Length Wt. Connection Capacitor Product Model Speed ated (Milli- Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. Type Number (rpm) Torque W HP) N (lbs.) XH mnm (oz-in.) PEMANENT SPLIT CAPACITO (NOMAL SLIP), NON-SYNCHONOUS 1250 21.5 (3.0) 2.8 (3.8) 50 230 1.060 25 (5.7) 63 (2.5) 1.1 (2.2) 074 10021 494 00059 KCI-26 1713 XH 16.0 (0.63) 61.0 (2.41) SQ. 10.0 MIN. (0.39). 48.5 (1.91) STANDAD LEADS 305 +51 / -25 (12+2/ -1) Ø 5 h6 (.19) 0.8 (0.03) 48.5 (1.91) ( 4) M4x0.7-6H, 4 mm deep minimum on a 68 mm bolt circle 82

AC INTENATIONAL PODUCTS 30 MOTOS 18-19 WATTS (1/41-1/39 HP) (4) M5X.8-6H, 8mm deep minimum on a 95 mm bolt circle 34 MOTOS For optional terminal box model 1982, see page 100. Capacitor 494 00091 shown on page 30. Output Input adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. 2 Type Number 1 Nm (oz-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 2850.06 (.9) 19 (1/39) 50 230 1 0.38 80 (18) 93.7 (3.69) 2.1 (4.6) 074 10021 494 00091 302BECI 1319 1400.13 (18) 18 (1/41) 50 230 1.21 80 (18) 93.7 (3.69) 2.1 (4.6) 074 10021 494 00091 302BECI N1340 90.9 (3.58) Shown with standard terminal box 75-100 WATTS (1/10-1/7.5 HP) For more information see page 16 Output Input adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (oz-in.) THEE PHASE, NON-SYNCHONOUS 1400.69 (97) 100 (1/7.5) 50 230/400 3.78/.45 185 (42) 168 (6.7) 4.4 (9.8) 074 10279 346BFPP 1295 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 1400.51 (72) 75 (1/10) 50 230 1.60 185 (42) 168 (6.7) 4.4 (9.8) 074 10021 494 00031 346BFCI 1291 XH 102.1 (4.02) 104.1 (4.10) XH 3.1 (0.12) 2.3 (.09) 16.0 (0.63) 13.2 (0.52) 5.84 (0.23) Ø 7 h6 (0.28) 20.0 (.78) Ø9 h6 (.35) STANDAD LEADS 305 +51/-25 (12 +2/-1) 3x3x14 (.12x.12x.55) KEY 67.1 (2.64) 53.1 (2.09) 86.6 (3.41) 67.3 (2.65) SQ. EF. 45 23.1 (.91) EF. For more information see page 15 50.0 (Ø 1.97) 46.0 (1.81) EF. 38.1 (1.499) 38.0 (1.495) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC M5X.8-6H, 8mm deep minimum on a 65 mm bolt circle 83

AC INTENATIONAL PODUCTS 42 MOTO Shown with standard terminal box 100-140 WATTS (1/7.5-1/5 HP) For more information see page 17 Output Input adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (oz-in.) THEE PHASE, NON-SYNCHONOUS 1400.95 (135) 140 (1/5) 50 230/400 3 1.1/.61 220 (50) 170 (6.7) 5.3 (11.8) 074 10279 _ 425BFPP 1273 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 1400.68 (97) 100 (1/7.5) 50 230 1.78 220 (50) 170 (6.7) 5.3 (11.8) 074 10021 494 00031 425BFCI 1358 XH 2.5 (0.09) 102.1 (4.02) 7.9 (0.31) MIN. 7.1(.28) 56.9 (2.24) 42.7 Ø 119.9 (4.72) (1.68) Ø 11 h6 (0.43) 23.0 (0.90) 4x4x16 KEY (0.16SQ X 0.63) 67.1 (2.64) Ø109.0 (4.29) Ø 60.0 (2.36) 45 45 66.5 (2.62) 126.5 (4.98) 53.1 (2.09) 115.1 (4.53) 26.4 (1.04) 22.1 (0.87) 53.1 (2.09) EF. 88.9 (3.50) M5X.8-6H, 8 mm deep minimum on a 75 mm bolt circle K-2 GEAMOTO 24A.67 MOTO Nm (95 OZ-IN.) MAXIMUM For more information see page 19 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W Hz V Ph Milli - atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number (rpm) Torque (Milli-HP) Amps N (oz.) XH (not Nm (oz-in.) supplied) PEMANENT SPLIT CAPACITO (NOMAL SLIP), NON-SYNCHONOUS 7.67 (95) 2.8 (3.8) 50 230 1 60 180 5.5 (20) 84.4 (3.3) 1.3 (2.9) 074 10021 494 00059 KCI-26T4 1757 42.53 (75) 2.8 (3.8) 50 230 1 60 30 5.5 (20) 80.4 (3.2) 1.3 (2.9) 074 10021 494 00059 KCI-26A2 1754 69.31 (45) 2.8 (3.8) 50 230 1 60 18 5.5 (20) 80.4 (3.2) 1.3 (2.9) 074 10021 494 00059 KCI-26A2 1753 210.11 (15) 2.8 (3.8) 50 230 1 60 6 5.5 (20) 80.4 (3.2) 1.3 (2.9) 074 10021 494 00059 KCI-26A2 1752 XH 23.2 (0.91) 6.5 (0.26) 16.0 (0.63) 10 (.39) MIN. 4.22 (.17) Ø 13.5 (0.53) NOT MACHINED 61.0 (2.40) SQ. Ø 5 h6 (.20) 48.5 (1.91) 15.0 (0.59) 90 ±1 (4) M4x7-6G, on 68 mm bolt circle STANDAD LEADS 304+51 / -25 (12+2 / -1) 8.4 (0.33) 84

AC INTENATIONAL PODUCTS 30-D GEAMOTO 24A 4.5 MOTO Nm (40 LB-IN.) MAXIMUM For more information see page 20 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO (NOMAL SLIP), NON-SYNCHONOUS 7.8 4.5 (40) 15 (1/48) 50 230 1 0.17 180 285 (65) 132.8 (5.2) 2.6 (5.9) 074 10021 494 00091 301BECI-D4 N1562 23 4.5 (40) 18 (1/41) 50 230 1 0.21 60 285 (65) 139.2 (5.5) 2.8 (6.3) 074 10021 494 00091 302BECI-D3 1574 47 2.7 (24) 18 (1/41) 50 230 1 0.21 30 285 (65) 139.2 (5.5) 2.8 (6.3) 074 10021 494 00091 302BECI-D3 1573 78 1.6 (14) 18 (1/41) 50 230 1 0.21 18 285 (65) 139.2 (5.5) 2.8 (6.3) 074 10021 494 00091 302BECI-D3 N1572 117 1.1 (9.7) 18 (1/41) 50 230 1 0.21 12 285 (65) 139.2 (5.5) 2.8 (6.3) 074 10021 494 00091 302BECI-D3 N1571 90.9 (3.58) 67.3 Vent hole (2.65) SQ. EF (4) M5x.8-6H on a 95 mm bolt circle 34-Z GEAMOTO 11.3 NM (100 LB-IN.) MAXIMUM XH STANDAD LEADS 304+51/-25 (12+2/-1) 14.3 (0.56) Shown with standard terminal box 38.8 (1.53) 23.0 (0.9) For more For more information information see page see page?? 21 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 7.8 11.3 (100) 50 (1/15) 50 230 1.48 180 555 (125) 217 (8.54) 4.5 (10.1) 074 10021 494 00029 344BFCI-Z4 N1449 23 11.3 (100) 50 (1/15) 50 230 1.48 60 555 (125) 217 (8.54) 4.5 (10.1) 074 10021 494 00029 344BFCI-Z3 1455 78 4.1 (36) 50 (1/15) 50 230 1.48 18 450 (100) 194 (7.64) 4.5 (10.1) 074 10021 494 00029 344BFCI-Z2 N1453 233 1.7 (15) 50 (1/15) 50 230 1.48 6 450 (100) 194 (7.64) 4.5 (10.1) 074 10021 494 00029 344BFCI-Z2 N1451 XH For optional terminal box model 1982, see page 100. Ø 11 h6 (0.43) 18.0 (0.7) 38.8 (1.53) 104.1 (4.10) 14.3 (0.58) 1.5 (0.06) 18.0 (0.71) 4 SQ 4.1 (0.16X0.16) 18.8 (0.74) 86.6 (3.41) SQ. Ø 29.0 (1.14) NOT MACH. 33.0 (1.3) EF. 102.1 (4.02) 68.6 ±0.8 Vent hole (2.7 ±0.03) ( 4) M5x0.8-6H, 9.6 mm deep minimum on a 95 mm bolt circle Ø 11 h6 (0.43) 23.0±0.03 (0.9±0.001) 4 SQ. (0.16) 67.1 (2.64) MAX 53.1 (2.09) MAX 31.0 (1.22) S 86.4 (3.40) SQ. 28 (1.1) NOT. MACH. 14.7 (0.58) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 85

AC INTENATIONAL PODUCTS 34-W GEAMOTO Shown with standard terminal box 24A 19.8 MOTO Nm (175 LB-IN.) MAXIMUM NON-SYNCHONOUS For more For information more information see page see?? page 22 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 4.5 19.8 (175) 75 (1/10) 50 230 1.60 312.4 575 (130) 234 (9.20) 5.7 (12.8) 074 10021 494 00031 346BFCI-W4 1477 21 16.5 (146) 75 (1/10) 50 230 1.60 65.5 575 (130) 234 (9.20) 5.7 (12.8) 074 10021 494 00031 346BFCI-W3 1484 69 6.0 (53) 75 (1/10) 50 230 1.60 20.4 290 (65) 234 (9.20) 5.7 (12.8) 074 10021 494 00031 346BFCI-W2 1481 255 1.6 (14) 75 (1/10) 50 230 1.60 5.5 290 (65) 234 (9.20) 5.7 (12.8) 074 10021 494 00031 346BFCI-W2 1478 104.1 (4.10) 102.1 (4.02) XH 5.6 (0.22) Vent hole ( 4) M6x1-6H, 12.7 mm deep minimum on a 121 mm bolt circle 64.0 (2.52) 46.0 (1.81) 1.5 (.06) 30 (1.18) Ø 14 h6 (.55) 15.0 (0.59) 25.0 (.98) 1.02 (0.04) 53.1 0.76 (0.03) 5 (.20)SQ. 67.1 (2.64) (2.09) 21.1 (0.83) 103.9 (4.09) Ø 33.3 (1.31) 29.0 (1.14) 85.9 (3.38) Ø 86.1 (3.39) 103.6 (4.08) SQ. 42-E GEAMOTO Shown with standard terminal box 24A 38.5 MOTO Nm (341 LB-IN.) MAXIMUM For more information see page 23 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) THEE PHASE, NON-SYNCHONOUS 140 5.7 (50) 140 (1/5) 50 230/400 3 1.1/.61 10 1300 (300) 231 (9.08) 6.8 (15.3) 074 10279 425BFPP-E2 1665 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 4.7 35 (310) 100 (1/7.5) 50 230 1.78 300 900 (200) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E4 1671 7.8 38.5 (341) 100 (1/7.5) 50 230 1.78 180 900 (200) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E4 1669 23 33.6 (297) 100 (1/7.5) 50 230 1.78 60 900 (200) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E3 1685 47 16.7 (148) 100 (1/7.5) 50 230 1.78 30 1300 (300) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E3 1683 70 11.2 (99) 100 (1/7.5) 50 230 1.78 20 1300 (300) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E3 1681 140 5.6 (50) 100 (1/7.5) 50 230 1.78 10 1300 (300) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E2 1680 280 2.9 (26) 100 (1/7.5) 50 230 1.78 5 1300 (300) 231 (9.08) 6.8 (15.3) 074 10021 494 00031 425BFCI-E1 1679 SPLIT PHASE (WITH CENTIFUGAL SWITCH), NON-SYNCHONOUS For more information see page?? 47 16.7 (148) 100 (1/7.5) 50 230 1 1.4 30 1300 (300) 231 (9.08) 6.8 (15.3) 074 10132 425BFSI-E3 1653 Vent hole ( 4) M-6x1-6H, 12.7 mm deep minimum on a 130 mm bolt circle XH 66.5 (2.62) 3.6 (0.14) 102.1 (4.02)MAX Ø 120.7 (4.75) 51.7 (2.04) 1.5 (0.06) 10.2 (0.4) 40.0 (1.57) Ø 19 h6 (0.75) 1.0 (0.04) 0.8 (0.03) 25.0 (0.98) 6 SQ. (0.24) 67.1 (2.64) MAX 53.1 (2.09) 115.1 (4.53) 119.4 (4.70) Ø 96.0 (3.78) 91.9 (3.62) Ø 39.1 (1.54) 31.8 (1.25) 22.9 (0.9) 86

AC INTENATIONAL PODUCTS 34-3F GEAMOTO Shown with standard terminal box 4.2 Nm (37 LB-IN.) MAXIMUM For more information see page 25 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 35 4.2 (37) 50 (1/15) 50 230 1.50 40 180 (40) 221 (8.69) 4.5 (10.1) 074 10021 494 00029 344BFCI-3F 1491 47 3.8 (34) 50 (1/15) 50 230 1.50 30 180 (40) 221 (8.69) 4.5 (10.1) 074 10021 494 00029 344BFCI-3F 1487 70 3.4 (30) 50 (1/15) 50 230 1.50 20 180 (40) 221 (8.69) 4.5 (10.1) 074 10021 494 00029 344BFCI-3F 1490 140 2.1 (19) 50 (1/15) 50 230 1.50 10 22 (5) 221 (8.69) 4.5 (10.1) 074 10021 494 00029 344BFCI-3F N1488 XH 102.1 (4.02) Ø11 h6 (0.43) 104.1 (4.10) 25.4 (1.0) 30.2 (1.19) 50.8 (2.0) 54.4 66.0 (2.60) (2.14) ( 4) M6x1-6H, 11 mm deep minimum 34-5F GEAMOTO 40.6 (1.60) 39.4 (1.55) 27.4 (1.08) 33.0 (1.30) Shown with standard terminal box 25.4±.8 (1.0±0.03) 18 (0.71) 53.1 (2.09) MAX 4 (0.16) SQ. 36.8 (1.45) 1.5 (0.06) 8.1 Nm (72 LB-IN.) MAXIMUM For more information see page 26 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) PEMANENTSPLIT CAPACITO, NON-SYNCHONOUS 23 8.1 (72) 50 (1/15) 50 230 1.50 60 220 (50) 232 (9.15) 5.6 (12.3) 074 10021 494 00029 344BFCI-5F 1469 35 6.8 (60) 50 (1/15) 50 230 1.50 40 220 (50) 232 (9.15) 5.6 (12.3) 074 10021 494 00029 344BFCI-5F 1468 70 4.4 (39) 50 (1/15) 50 230 1.50 20 220 (50) 232 (9.15) 5.6 (12.3) 074 10021 494 00029 344BFCI-5F 1466 140 2.4 (21) 50 (1/15) 50 230 1.50 10 132 (30) 232 (9.15) 5.6 (12.3) 074 10021 494 00029 344BFCI-5F 1465 102.1(4.02) XH 38.1 (1.5) EF. 104.1 (4.10) 76.2±0.25 (3.0±0.01) 53.1(2.09) 90.9 (3.58) 45.5 (1.79) 43.7 (1.72) 40.6 (1.6) EF. Oil level plug 15.1 (0.59) EF. 42.4 ±0.127 (1.67 ±0.005) 67.1 (2.64) 36.0 (1.42) 25.0 (0.98) 53.1 (2.09) 67.1(2.64) 5 (0.20)SQ. Ø 14 h6 (0.55) 4 HOLES 6.6 (0.26) 41.4 (1.63) 46.0 (1.81) 1.5 (0.06) 46.0 (1.81) 36.8 (1.45) 133.9 (5.27) 113.0 (4.45) 6.4 (0.25) EF. 82.6± 0.8 (3.25±0.03) 97.8 (3.85) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC "C" standard location of breather hole 87

AC INTENATIONAL PODUCTS 42-5F GEAMOTO 10.5 Nm (93 LB-IN.) MAXIMUM Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 35 10.5 (93) 83 (1/9) 50 230 1.63 40 335 (80) 246 (9.69) 6.4 (14.3) 074 10021 494 00031 424BFCI-5F N1627 70 6.8 (60) 83 (1/9) 50 230 1.63 20 335 (80) 246 (9.69) 6.4 (14.3) 074 10021 494 00031 424BFCI-5F N1624 140 3.6 (32) 83 (1/9) 50 230 1.63 10 45 (10) 246 (9.69) 6.4 (14.3) 074 10021 494 00031 424BFCI-5F 1623 XH 53.3 (2.1) MAX Shown with standard terminal box 43.7 (1.72) 5 (0.20) SQ. 25 (0.98) 53.1(2.09) Ø 14 h6 (0.55) OIL LEVEL Ø 120.7 4 HOLES [6.86 (0.27) I.D.] PLUG ( 4.75) 38.1(1.5) 41.4(1.63) 102.1 (4.02) 76.2 (3.0) 82.6 (3.25) 6.4 90.9 (3.58) 97.8 (3.85) (0.25) "C" standard location of breather hole 40.6 (1.60 ) EF. 42.4±0.127 (1.67±.005) 67.1 (2.64) 36.0 (1.41) 46.0 (1.81) 1.5 (0.06) 46.0 (1.81) 144.8 (5.7) 42-5N GEAMOTO Shown with standard terminal box 12.8 NM (113 LB-IN.) MAXIMUM For more information see page 27 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) THEE PHASE, NON-SYNCHONOUS 47 12.3 (109) 140 (1/5) 50 230/400 3 1.1/.61 30 800 (180) 260 (10.25) 7.3 (16.3) 074 10279 425BFPP-5N 1633 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 35 12.8 (113) 100 (1/7.5) 50 230 1 0.78 40 800 (180) 260 (10.25) 7.3 (16.3) 074 10021 494 00031 425BFCI-5N 1678 70 8.4 (74) 100 (1/7.5) 50 230 1 0.78 20 800 (180) 260 (10.25) 7.3 (16.3) 074 10021 494 00031 425BFCI-5N 1677 XH 53.1 (2.09) 43.7 (1.72) 5 (0.20)SQ. 115.1 (4.53) 46.0 (1.81) 46.0 (1.81) 53.1 (2.09) 30 (1.18) 67.1 (2.64) 145.0 (5.71) 102.1 (4.02) MAX Ø 120.7 (4.75) 38.1 (1.50) (4) Ø 6.86 (0.27) 76.2 (3.0) 90.9 (3.58) Ø 14 h6 (0.55) 25 (.98) 36 (1.42) 45.5 (1.79) 40.6 (1.6) EF. 42.4±0.127(1.67±0.005) 6.4 (0.25) EF. 41.4 (1.63) EF. 97.8 (3.85) OIL LEVEL PLUG 82.6±0.8 (3.25±0.03) "C" standard location of breather hole 88

AC INTENATIONAL PODUCTS 42-GB GEAMOTO 42.9 Nm (380 LB-IN.) MAXIMUM For more information see page 28 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 23 23(204) 100 (1/7.5) 50 230 1.78 60 900 (200) 294 (11.57) 8 (17.5) 074 10021 494 00031 425BFCI-GB 1260 12 33 (290) 100 (1/7.5) 50 230 1.78 120 900 (200) 294 (11.57) 8 (17.5) 074 10021 494 00031 425BFCI-GB N1262 7.4 42 (375) 100 (1/7.5) 50 230 1.78 190 900 (200) 294 (11.57) 8 (17.5) 074 10021 494 00031 425BFCI-GB N1264 5 43 (380) 100 (1/7.5) 50 230 1.78 280 900 (200) 294 (11.57) 8 (17.5) 074 10021 494 00031 425BFCI-GB 1266 102.1 (4.02) 120.7 (4.75) DIA. XH (4) M6X1 6H 10 DEEP MIN. Shown with standard terminal box 126.5 (4.98) 80.8 (3.18) 34.2 (1.34) 76.2 (3.0) (3) M8x1, 25-6H, 10 mm deep minimum on a 74 mm bolt circle "C" standard location of breather hole 90 34.2 (1.34) 25 (0.98)EF. 50.8 (2.0) 54.6 (2.15) 19.1 (0.75) 53.1 (2.09) OIL LEVEL PLUG 67.1 (2.64) 6 (0.25) SQ. KEY 60.0 (2.36) 31.0 (1.22) 55.1 (2.17) OIL LEVEL PLUG 13.8(0.544) EF. 129.5 (5.10) Ø 19 h6 (0.75) 16.8 (0.66) 50.8 (2.00) 91.4 (3.60) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 89

DC INTENATIONAL PODUCTS DC CONNECTION DIAGAM 074 10097 BOWN BLUE GEEN-YELLOW T. + - MOTO INSULATION ATINGS The performance ratings are based on Class F insulation material (155 C total). Connect as shown for clockwise rotation while viewing output shaft. To reverse direction, transpose brown and blue leads. TOQUE CONVESION TABLE To convert from A to B multiply by entry intercept A B Nm N-cm kg-cm g-cm lb-in. oz-in. Nm 1 100 10.2 10,200 8.851 141.6 N-cm.01 1.102 101.97.089 1.42 kg-cm.0981 9.81 1 1,000.868 13.9 g-cm.0000981.0098.001 1.00087.014 lb-in..113 11.3 1.152 1,152 1 16 oz-in..0072.72.072 72.0625 1 1 HP = 746 W 1 inch = 25.4 mm 1 lb-in.-sec 2 = 7061 kg-mm 2 24A MOTO 14-32 WATTS (1/53-1/23 HP) 180VDC, FF=1.6 Continuous Duty For more information see page 33 Speed ated ated W (HP) KT KE Winding Winding otor adial Length Wt. Product Model (rpm) Torque Amps (oz-in./a) (V/krpm) es. Ind. Inertia Load mm (inch) kg (lbs.) Type Number 1 Nm (oz-in.) ohms mh kg mm 2 N (lbs.) XH 1725.08 (12).13 14 (1/53) 140 104 320 340 42 110 (25) 99.8 (3.93) 1.3 (2.8) 24A2BEPM 1041 1725.12 (18).18 21 (1/35) 140 104 200 240 60 110 (25) 119 (4.68) 1.5 (3.4) 24A4BEPM N1043 3000.11 (16).30 32 (1/23) 80 60 70 100 60 110 (25) 119 (4.68) 1.5 (3.4) 24A4BEPM 1045 91.4 (3.60) 61.5 (2.42) SQ. XH EF. 16.0 (0.63) EF. 3.2 (0.13) Ø 26 h9 (1.02) DIA. Ø 7 h6 (0.28) 61.5 (2.42) O.D. 610 +51/-25 (24 +2/-1) STANDAD LEADS 21.0 (0.83) 51.0 (2.00) 49.0 (1.93) (4) slots 4.7 mm (0.186 in.) wide on a 69-72 mm (2.7-2.83 in.) bolt circle 90

DC INTENATIONAL PODUCTS 32A MOTO Shown with optional terminal box model 1984 (see page 100) 29-82 WATTS (1/25-1/9 HP) 180VDC, FF=1.6 Continuous Duty For more information see page 34 Speed ated ated W (HP) KT KE Winding Winding otor adial Length Wt. Product Model (rpm) Torque Amps (oz-in./a) (V/krpm) es. Ind. Inertia Load mm (inch) kg (lbs.) Type Number Nm (oz-in.) (ohms) Mh kg mm 2 N (lbs.) XH 1725.18 (25).25 29 (1/25) 140 105 110 200 170 240 (55) 133 (5.22) 2.8 (6.3) 32A3BEPM 4216 1725.30 (42).41 50 (1/15) 140 105 60 120 270 240 (55) 160 (6.28) 3.6 (8) 32A5BEPM 4218 3000.28 (40).62 82 (1/9) 80 60 20 42 270 240 (55) 160 (6.28) 3.6 (8) 32A5BEPM 4221 INTODUCTION XH 53.1 (2.09) 102.1 (4.02) 86.6 (3.41) DIA. 12.7 (0.50) (4) m5 x 0.8-6H,6.4 mm (.25 in.) deep minimum on a 65 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. 2.3 (0.09) 20 (0.79) 14 (0.55) 3 (0.12) SQ. Ø 9 h6 (0.35) 42A MOTO Shown with optional terminal box model 1984 (see page 100) 111.3 (4.38) 67.1 (2.64) 50 h9 (1.97) 65.0 (2.56) 86.6 (3.41) 102.0 (4.01) 112-185 WATTS (1/6.7-1/4 HP) 180VDC, FF=1.6 Continuous Duty For more information see page 35 Speed ated ated W (HP) KT KE Winding Winding otor adial Length Wt. Product Model (rpm) Torque Amps (oz-in./a) (V/krpm) es. Ind. Inertia Load mm (inch) kg (lbs.) Type Number 1 Nm (oz-in.) ohms mh kg mm 2 N (lbs.) XH 1725.68 (95).85 112 (1/6.7) 140 105 19 62 580 400 (90) 171 (6.72) 5.9 (13) 42A5BEPM 4227 3000.49 (70) 1.17 143 (1/5) 80 60 6.6 19 580 400 (90) 171 (6.72) 5.9 (13) 42A5BEPM 4230 1725.85 (120) 1.0 141 (1/5) 140 105 14 46 850 400 (90) 200 (7.87) 7.3 (16) 42A7BEPM N4237 3000.63 (90) 1.5 185 (1/4) 80 60 5.4 14 850 400 (90) 200 (7.87) 7.3 (16) 42A7BEPM N4231 108.2 (4.26) DIA. 57.2± 0.25 (2.25±0.01) 73.2 (2.88) XH 102.1 (4.02) 12.7 (0.50) 2.5 (0.10) 30 (1.18) 25 (0.98) Ø 14 h6 (0.55) 37.3 (1.47) 5 (0.20)SQ. 7.1 (0.28) EF. 117.3 (4.62) DIA. 66.8 (2.63) 44.5 (1.75) EF. 67.1 (2.64) 88.9 (3.50) 120.7 (4.75) EF. 45 45 70 h9 (2.76) 53.1 (2.09) 121.2 (4.77) 22.4 (0.88) INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC (4) m6 x 1-6H, 7.6 mm (.30) deep minimum on 85mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. 91

DC INTENATIONAL PODUCTS 24A-D GEAMOTO 24A 4.5 MOTO Nm (40 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 36 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 5.8 4.5 (40) 6.2 (55) 14 (1/53) 300.13 285 (65) 152 (5.97) 1.9 (4) 24A2BEPM-D5 N1398 9.6 4.5 (40) 6.2 (55) 14 (1/53) 180.13 285 (65) 152 (5.97) 1.9 (4) 24A2BEPM-D4 1397 29 4.5 (40) 6.2 (55) 21 (1/35) 60.18 285 (65) 171 (6.72) 2.0 (4.5) 24A4BEPM-D3 1395 58 2.6 (23) 4.8 (42) 21 (1/35) 30.18 285 (65) 171 (6.72) 2.0 (4.5) 24A4BEPM-D3 1394 144 1.0 (9.2) 1.8 (16) 21 (1/35) 12.18 285 (65) 171 (6.72) 2.0 (4.5) 24A4BEPM-D3 N1392 106.0 (4.17) EF. 91.4 (3.60) XH 22.1 (0.87) EF. 38.8±.8 (1.53) 29.0 (1.14) DIA. 14.3 (0.56) 18 (0.71). 4 (0.16) SQ. 14.7 (0.58) EF. 86.6 (3.41) SQ. 2.3 (0.09) EF. Ø 11 h6 (0.43) 2.3 (0.09) EF. 61.5 (2.42) DIA. STD. LEADS 610 +51/-25 (24+2/-1) 67.3±0.8 (2.65±0.03) TYP. Vent hole ( 4) 1M5x0.8-5H, 9.6 mm (.38 in.) deep minimum on a 95 mm bolt circle 24A-Z GEAMOTO 24A 11.3 MOTO Nm (100 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 37 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 9.6 11.3 (100) 13 (115) 21 (1/35) 180.18 555 (125) 199 (7.82) 2.3 (5) 24A4BEPM-Z4 N1163 29 5.2 (46) 13 (115) 21 (1/35) 60.18 555 (125) 199 (7.82) 2.3 (5) 24A4BEPM-Z3 1161 58 2.5 (23) 8.3 (75) 21 (1/35) 30.18 555 (125) 199 (7.82) 2.3 (5) 24A4BEPM-Z3 N1160 288.56 (5) 1.9 (17) 21 (1/35) 6.18 450 (100) 176 (6.92) 2.3 (5) 24A4BEPM-Z2 N1157 XH 7.6 (0.30) 40 (1.57) 18 (0.71) 4(0.16)SQ. 94.1 (3.60) 86.6 (3.41) SQ. 29.0 (1.14) NOT. MACH. 14.7 (0.58) EF. Ø 11 h6 (0.43) 61.5 (2.42) DIA. 33.8 (1.33) EF. STD. LEADS 610 +51/-25 (24"+2/-1) 67.3±0.8 (2.65±0.03) 106.0 (4.17) EF. Vent hole (4) 1M5x0.8-6H, 9.6 mm (.38 in.) deep minimum on a 95 mm bolt circle 92

DC INTENATIONAL PODUCTS 32A-Z GEAMOTO 6.4 Nm (57 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 38 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 29 6.4 (57) 13 (115) 29 (1/25) 60.25 555 (125) 201 (7.90) 3.9 (8.6) 32A3BEPM-Z3 4269 58 3.8 (35) 8.0 (71) 29 (1/25) 30.25 555 (125) 201 (7.90) 3.9 (8.6) 32A3BEPM-Z3 N4268 144 1.6 (14) 3.2 (29) 29 (1/25) 12.25 450 (100) 178 (7.00) 3.9 (8.6) 32A3BEPM-Z2 N4266 53.1 (2.09) XH 102.1 (4.02) 86.6 (3.41) DIA. 32A-W GEAMOTO 53.1 (2.09) Shown with optional terminal box model 1984 (see page 100) 7.6 (0.30) 38.8 (1.53) Ø 11 h6 (0.43) 4(0.16) SQ. 67.1 (2.64) 29.0 (1.14) NOT. MACH. 18 (0.71) 111.0 (4.37) 67.3±0.76 (2.65±0.03) 102 (4.01) 86.6 (3.41) 33.8 (1.33) 14.7 (0.58) EF. Vent hole (4) M5x0.8-6H, 9.6 mm deep minimum on a 95 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. Shown with optional terminal box model 1984 (see page 100) 24A 19.8 MOTO Nm (175 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 39 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 5.5 19.8 (175) 23.7 (210) 29 (1/25) 312.4.25 575 (130) 197 (7.75) 4.5 (10) 32A3BEPM-W4 4247 18 16.6 (147) 23.7 (210) 50 (1/15) 97.5.41 575 (130) 224 (8.81) 5.4 (11.75) 32A5BEPM-W4 N4256 39 8.7 (77) 14.8 (130) 50 (1/15) 43.9.41 575 (130) 224 (8.81) 5.4 (11.75) 32A5BEPM-W3 4254 85 4.3 (38) 7.2 (64) 50 (1/15) 20.4.41 290 (65) 224 (8.81) 5.4 (11.75) 32A5BEPM-W2 N4252 125 3.1 (28) 5.2 (47) 50 (1/15) 13.8.41 290 (65) 224 (8.81) 5.4 (11.75) 32A5BEPM-W2 4251 315 1.1 (10) 1.9 (17) 50 (1/15) 5.48.41 290 (65) 224 (8.81) 5.4 (11.75) 32A5BEPM-W2 N4249 XH 46 (1.81) 67.1 (2.64) 102.1 (4.02) EF. 33.3 (1.31) DIA. 64.0 (2.52) 15 (0.59) 5.6 (0.22) 29.0 (1.14) 30 (1.18) Ø 14 h6 (0.55) 25 (0.98) 5 (0.20) SQ. 86.6 (3.41) DIA. 85.9 (3.38 ) SQ. 86.1 (3.39) DIA. Vent hole ( 4) M6x1-6H, 12.7 mm deep minimum on a 121 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. 21.1 (0.83) 103.6 (4.08) SQ. INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 93

DC INTENATIONAL PODUCTS 42A-E&F GEAMOTO 24A 35.0 MOTO Nm (310 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 40 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 5.8 35 (310) 53.7 (475) 112 (1/6.7) 300.85 900 (200) 238 (9.37) 7.3 (16) 42A5BEPM-E4 4275 29 35 (310) 53.7 (475) 141 (1/5) 60 1.0 900 (200) 267 (10.5) 8.6 (19) 42A7BEPM-E3 N4285 43 27 (240) 32 (282) 141 (1/5) 40 1.0 900 (200) 267 (10.5) 8.6 (19) 42A7BEPM-E3 4284 85 13.6 (120) 16 (141) 141 (1/5) 20 1.0 1300 (300) 267 (10.5) 8.6 (19) 42A7BEPM-E3 4282 170 6.8 (60) 12.0 (106) 141 (1/5) 10 1.0 1300 (300) 267 (10.5) 8.6 (19) 42A7BEPM-E2 4280 170 7.7 (68) 39.0 (345) 141 (1/5) 10 1.0 1300 (300) 267 (10.5) 8.6 (19) 42A7BEPM-F2 N4290 345 3.7 (32) 8.2 (73) 141 (1/5) 5 1.0 1300 (300) 267 (10.5) 8.6 (19) 42A7BEPM-E1 4279 XH 51(2.01) 102.1 (4.02) 10.0 (0.39) EF. 108.2 (4.26) DIA. Shown with optional terminal box model 1984 (see page 100) 3.6 (0.14) 1.5(0.06) 66.5 (2.62) 40 (1.57) 25 (0.98) 31.8 (1.25) 6 (0.24) SQ. Ø 19 h6 (0.75) 92.0 (3.62) 39.1 (1.54)DIA. 22.9 (0.90) 119.0 (4.70) 67.1 (2.64) 31.0 (1.22) 53.1 (2.09) 96.0 (3.78) DIA. Vent hole ( 4) M6x1-6H, 12.7 mm (0.5 in.) deep minimum on a 130 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. 118.1 (4.65) 24A-3F GEAMOTO 1.8 Nm (16 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 41 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 43 1.8 (16) 5.2 (46) 21 (1/35) 40.18 180 (40) 189 (7.4) 2.4 (5.3) 24A4BEPM-3F N1098 86 1.4 (11.6) 4.6 (41) 21 (1/35) 20.18 180 (40) 189 (7.4) 2.4 (5.3) 24A4BEPM-3F N1096 172.76 (6.4) 3 (26) 21 (1/35) 10.18 180 (40) 189 (7.4) 2.4 (5.3) 24A4BEPM-3F 1094 76.2 (3.0) EF. 41.1(1.62) 39.4 (1.55) 61.5 (2.42) DIA. XH 610+51/-25 (24 +2/-1) STANDAD LEADS (4) M6x1-6H 11 MIN. 25.4 (1.0) 50.8 (2.0) 65.0 (2.56) 27.4 (1.08) 33.0 (1.30) 91.4 (3.60) 24 (0.94) 36.8 36.8 (1.45) (1.45) 18 (0.71) 4 (0.16) SQ. Ø 11 h6 (0.43) 30.2 (1.19) 42.9 (1.69) MAX 92.2 (3.63) 94

DC INTENATIONAL PODUCTS 32A-5F GEAMOTO 4.0 Nm (35 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 42 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 43 4.0 (35) 13.3 (118) 50 (1/15) 40.41 335 (80) 10.35 (263) 5.4 (12) 32A5BEPM-5F 4244 86 3.2 (28) 11.3(100) 50 (1/15) 20.41 335 (80) 10.35 (263) 5.4 (12) 32A5BEPM-5F N4242 172 1.8 (16) 6.1 (54) 50 (1/15) 10.41 335 (80) 10.35 (263) 5.4 (12) 32A5BEPM-5F N4241 345 1.0 (8.6) 3.2 (28) 50 (1/15) 5.41 335 (80) 10.35 (263) 5.4 (12) 32A5BEPM-5F N4240 86.6 (3.41) DIA. XH 102.1 (4.02) 42A-5N GEAMOTO Shown with optional terminal box model 1984 (see page 100) Shown with optional terminal box model 1984 (see page 100) 9.5 Nm (84 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 43 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 43 9.5 (84) 20.0 (177) 112 (1/6.7) 40.85 530 (120) 263 (10.35) 7.6 (16.8) 42A5BEPM-5N N4238 85 8.0 (70) 20.0 (177) 112 (1/6.7) 20.85 530 (120) 263 (10.35) 7.6 (16.8) 42A5BEPM-5N 4236 172 4.5 (40) 13.2 (117) 112 (1/6.7) 10.85 530 (120) 263 (10.35) 7.6 (16.8) 42A5BEPM-5N N4235 XH 102.1 (4.02) 53.1 (2.09) 53.1 (2.09) 103.1 (4.06) EF. 38.1 (1.5) 51.6(2.03) 51.6 (2.03) 43.7 (1.72) 76.2 (3.0) 90.9 (3.58) 5 (0.20) SQ. 45.5 (1.79) 43.7(1.72) 5 (0.20)SQ 40.6 (1.60) 46.0 (1.81) 67.1 (2.64) Ø 117.1 (4.61) Ø 14 h6 (0.55) 108.2 (4.26) DIA. 4 [6.81(.268)] I.D. 112.3 (4.42) EF. 38.1 (1.50) 41.4 (1.63) 6.4 (0.25) EF. 76.2 (3.0) 82.6 (3.25) 90.9(3.58) 97.8 (3.85) Vent hole Without terminal box a 24 in. (+2/-1 in.) cord is standard. 42.4 (1.67) 40.6 (1.60) 42.4 (1.67) 36.1 (1.42) 25.0 (0.98) 46.0 (1.81) 67.1 (2.64) 111.0 (4.37) DIA. 36 (1.42) 25 (0.98) Ø 14 h6 (0.55) 4 HOLES 6.81 (.268) I.D. 41.4 (1.63) EF. 102.0 (4.01) 82.6±0.8 (3.25 ±0.03) 97.8 (3.85) 46.0 (1.81) 140.0 (5.51) 46.0 (1.81) 129 (5.08) 6.4 (0.25) EF. Vent hole Without terminal box a 24 in. (+2/-1 in.) cord is standard. INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 95

DC INTENATIONAL PODUCTS 42A-5H GEAMOTO Shown with optional terminal box model 1984 (see page 100) 14.2 Nm (126 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 44 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 36 14.2 (126) 38.4 (340) 141 (1/5) 48 1.0 665 (150) 330 (13.0) 16 (35.5) 42A7BEPM-5H 4299 96 9.2 (81) 27.9 (247) 141 (1/5) 18 1.0 665 (150) 330 (13.0) 16 (35.5) 42A7BEPM-5H N4296 XH 102.1 (4.02) 53.1 (2.09) 120.9 (4.76) EF. 67.1 (2.64) 108.2 (4.26) DIA. 64.3 (2.53) 71.4 (2.81) 25.0 (0.98) 39.9 (1.57) 111 (4.37 ) DIA. 141.0 (5.55) EF. 6 (0.24)SQ.. 19 h6 (0.75) 54.1 (2.13) EF. 76.5/75.7 (3.01/2.98) 185 (7.28) (4) [10.3(0.41)] I.D. HOLES 143.0 (5.63) 38.1 (1.50) EF 60.5 (2.38) EF. 98.6± 0.25 (3.88±0.01) 68.3 (2.69)EF. 136.7±0.5 (5.38±.0.02) 162.1 (6.38) 11.2 (0.44) EF. Vent hole Without terminal box a 24 in. (+2/-1 in.) cord is standard. 42A-GB GEAMOTO 42.8 Nm (380 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 45 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH 6.2 42.8 (380) 67.5 (600) 112 (1/6.7) 280.85 900 (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB N1366 9.0 42.8 (380) 67.5 (600) 112 (1/6.7) 190.85 900 (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB 1364 14.4 42.3 (377) 67.5 (600) 112 (1/6.7) 120.85 900 (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB 1362 28.8 31.2 (277) 53.9 (478) 112 (1/6.7) 60.85 900 (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB 1360 XH 610+51/-25 (24+2/-1) 126.5 (4.98) 80.8 (3.18) 34.2 (1.34) 34.2 (1.34) 108.2 (4.26) DIA. 90 19.1 (0.75) 76.2 (3.00) (4) HOLES M6X1 6H 10 DEEP MIN Vent hole ( 3) M8x1, 25-6H, 10 mm deep minimum on 74 mm B.C. ef. 50.8 (2.0) 54.6 (2.15) Ø 19 h6 (0.75) 60 (2.38) 25 (0.98) 6 (0.24) SQ. KEY 16.8 (0.66) 31.0 (1.22) 50.8 (2.00) 55.1 (2.17) 13.8 (0.544) EF. 123.2 (4.85) OIL LEVEL PLUG 96

DC INTENATIONAL PODUCTS UPM UNFILTEED SC DC CONTOLS CHASSIS, BASIC SPEED CONTOL For more information see page 52 W (HP) Input Voltage Output Voltage Continuous Output Peak Output Current Form Weight Product Model ating (VAC) 50/60 Hz (VDC) Current (Amps) (Amps) Factor kg (lbs.) Type Number 248 (1/3) 115/230 0-90/0-180 2.1 4.2 1.6.45 (1.0) UPM-3318C 0865 248 (1/3) 115/230 0-90/0-180 2.1 4.2 1.6.45 (1.0) UPM-3318C 0866 DIMENSIONS 12.7 (.50) TYP. 2.3 (.09) EF. FPM UNFILTEED SC DC CONTOLS CHASSIS, BASIC SPEED CONTOL W (HP) Input Voltage Output Voltage Continuous Output Peak Output Current Form Weight Product Model ating (VAC) (VDC) Current (Amps) (Amps) Factor kg (lbs.) Type Number 177 (1/4) 230 0-180 2.8 6.5 1.6 3.6 (8.0) FPM-1850C 1850 DIMENSIONS 92.5 (3.64) 63.5 (2.50) TYP. Model 0865 has 0.25" Q.C. tabs for connections. Model 0866 has a pluggable terminal block. 118.2 ±0.25 (4.654±.010) 63.5 (2.50) 27.7 (1.09) 2.4. (0.10.) (4 PL.) 6.4(.25) TYP. 96.52 (3.80) TYP. 109.2 (4.30) 2.38 (.094). SLOTS (6 PLACES) 152.9 (6.02) 6.4 (0.25) 165.6 (6.52) 38.1 (1.50) 31.8 (1.25) 24.1 (.95) TYP. CONNECTION DIAGAM wire and connector included with control Yellow (Pin 12) Orange (Pin 10) Blue (Pin 8) White (Pin 11) Black (Pin 7) 10k ohm Speed Potentiometer (included with control) Socket J1 To inhibit switch (optional) CONNECTION DIAGAM JP1 1 7 11 15 Line Hot (230VAC) PW. LMT. A1 L1 S3 S1 H1 A2 L2 S2 H2 Line Neutral (230VAC) Fuse * (supplied by user) Fuse (supplied by user) All wires external to control must be supplied by user * This fuse only should be used when L2 is not neutral (such as for 230 VAC operation in USA) FL ACC 16 MAX + MIN L N A1 A2 Optional Inhibit Switch (supplied by user) 10K Ω Speed Potentiometer (included with control) J2 EG. TOQ. MIN. DEC. ACC. TOQ DIP SWITCH SW Earth Ground PM Motor Armature } 115 VAC or 230 VAC Line Voltage Motor Armature FA EG C PENDING INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 97

DC INTENATIONAL PODUCTS FPM UNFILTEED SC DC CONTOLS IP-40 BASIC SPEED CONTOL W (HP) Input Voltage Output Voltage Continuous Output Peak Output Current Form Weight Product Model ating (VAC) (VDC) Current (Amps) (Amps) Factor kg (lbs.) Type Number 177 (1/4) 230 0-180 2.8 6.5 1.6 3.6 (8.0) FPM-1855E 1855 DIMENSIONS 156.5 (6.16) EF. CONNECTION DIAGAM Shown with enclosure door removed 100.1 (3.94) EF. 214.4 (8.44) EF. 156.5( 6.16) EF. LINE HOT LINE NEUTAL MOTO POSITIVE O NEGATIVE MOTO NEGATIVE O POSITIVE EATH GOUND Accepts.5 in. liquid tight fittings Note: All wires external to control must be supplied by user 98

DC INTENATIONAL PODUCTS SELECTION TABLE- UNFILTEED DC CONTOLS 230 VAC INPUT, SC DIVE FPM SYSTEM PEFOMANCE WHEN USING BODINE 180V PM MOTOS (180 VDC OUTPUT) Motor/Gearmotor Specifications Model Number Matching Control Model Numbers Encased Chassis Speed Cont. No Product Nameplate eference Accepts Quick Terminal ange Torque Accessory Type ating Page Optional Connect Block (rpm) Nm(lb-in.) Shaft W (HP) Interface Tabs MOTOS WITHOUT GEA EDUCES 50-1725 0.08 (0.75) 1041 24A2BEPM 14 (1/53) 90 1855 1850 0865 0866 40-1725 0.12 (1.13) 1043 24A4BEPM 21 (1/35) 90 1855 1850 0865 0866 60-1725 0.18 (1.56) 4216 32A3BEPM 29 (1/25) 91 1855 1850 0865 0866 40-3000 0.11 (1.0) 1045 24A4BEPM 32 (1/23) 90 1855 1850 0865 0866 60-1725 0.30 (2.6) 4218 32A5BEPM 50 (1/15) 91 1855 1850 0865 0866 60-3000 0.28 (2.5) 4221 32A5BEPM 82 (1/9) 91 1855 1850 0865 0866 60-1725 0.68 (5.9) 4227 42A5BEPM 112 (1/6.7) 91 1855 1850 0865 0866 60-1725 0.85 (7.5) 4237 42A7BEPM 141 (1/5) 91 1855 1850 0865 0866 60-3000 0.49 (4.4) 4230 42A5BEPM 143 (1/5) 91 1855 1850 60-3000 0.63 (5.6) 4231 42A7BEPM 185 (1/4) 91 1855 1850 PAALLEL SHAFT GEAMOTOS 0.17-5.8 4.5 (40) N1398 24A2BEPM-D5 14 (1/53) 92 1855 1850 0865 0866 0.28-9.6 4.5 (40) 1397 24A2BEPM-D4 14 (1/53) 92 1855 1850 0865 0866 0.22-9.6 11.3 (100) N1163 24A4BEPM-Z4 21 (1/35) 92 1855 1850 0865 0866 0.67-29 5.2 (46) 1161 24A4BEPM-Z3 21 (1/35) 92 1855 1850 0865 0866 0.67-29 4.5 (40) 1395 24A4BEPM-D3 21 (1/35) 92 1855 1850 0865 0866 1.3-58 2.5 (23) N1160 24A4BEPM-Z3 21 (1/35) 92 1855 1850 0865 0866 1.3-58 2.6 (23) 1394 24A4BEPM-D3 21 (1/35) 92 1855 1850 0865 0866 3.3-144 1.0 (9.2) N1392 24A4BEPM-D3 21 (1/35) 92 1855 1850 0865 0866 6.7-288 0.56 (5) N1157 24A4BEPM-Z2 21 (1/35) 92 1855 1850 0865 0866 0.19-5.5 19.8 (175) 4247 32A3BEPM-W4 29 (1/25) 93 1855 1850 0865 0866 1-29 6.4 (57) 4269 32A3BEPM-Z3 29 (1/25) 93 1855 1850 0865 0866 2-58 3.8 (35) N4268 32A3BEPM-Z3 29 (1/25) 93 1855 1850 0865 0866 5-144 1.6 (14) N4266 32A3BEPM-Z2 29 (1/25) 93 1855 1850 0865 0866 0.62-18 16.6 (147) N4256 32A5BEPM-W4 50 (1/15) 93 1855 1850 0865 0866 1.4-39 8.7 (77) 4254 32A5BEPM-W3 50 (1/15) 93 1855 1850 0865 0866 2.9-85 4.3 (38) N4252 32A5BEPM-W2 50 (1/15) 93 1855 1850 0865 0866 4.3-125 3.1 (28) 4251 32A5BEPM-W2 50 (1/15) 93 1855 1850 0865 0866 11-315 1.1 (10) N4249 32A5BEPM-W2 50 (1/15) 93 1855 1850 0865 0866 0.2-5.8 35 (310) 4275 42A5BEPM-E4 112 (1/6.7) 94 1855 1850 0865 0866 1-29 35 (310) N4285 42A7BEPM-E3 141 (1/5) 94 1855 1850 0865 0866 1.5-43 27 (240) 4284 42A7BEPM-E3 141 (1/5) 94 1855 1850 0865 0866 3-85 13.6 (120) 4282 42A7BEPM-E3 141 (1/5) 94 1855 1850 0865 0866 6-170 7.7 (68) N4290 42A7BEPM-F2 141 (1/5) 94 1855 1850 0865 0866 6-170 6.8 (60) 4280 42A7BEPM-E2 141 (1/5) 94 1855 1850 0865 0866 12-345 3.7 (32) 4279 42A7BEPM-E1 141 (1/5) 94 1855 1850 0865 0866 IGHT ANGLE GEAMOTOS 1-43 1.8 (16) N1098 24A4BEPM-3F 21 (1/35) 94 1855 1850 0865 0866 2-86 1.4 (11.6) N1096 24A4BEPM-3F 21 (1/35) 94 1855 1850 0865 0866 4-172 0.76 (6.4) 1094 24A4BEPM-3F 21 (1/35) 94 1855 1850 0865 0866 1.5-43 4.0 (35) 4244 32A5BEPM-5F 50 (1/15) 95 1855 1850 0865 0866 3-86 3.2 (28) N4242 32A5BEPM-5F 50 (1/15) 95 1855 1850 0865 0866 6-172 1.8 (16) N4241 32A5BEPM-5F 50 (1/15) 95 1855 1850 0865 0866 12-345 1.0 (8.6) N4240 32A5BEPM-5F 50 (1/15) 95 1855 1850 0865 0866 0.2-6.2 42.8 (380) N1366 42A5BEPM-GB 112 (1/6.7) 96 1855 1850 0865 0866 0.3-9.0 42.8 (380) 1364 42A5BEPM-GB 112 (1/6.7) 96 1855 1850 0865 0866 0.5-14.4 42.3 (377) 1362 42A5BEPM-GB 112 (1/6.7) 96 1855 1850 0865 0866 1-28.8 31.2 (277) 1360 42A5BEPM-GB 112 (1/6.7) 96 1855 1850 0865 0866 1.5-43 9.5 (84) N4238 42A5BEPM-5N 112 (1/6.7) 95 1855 1850 0865 0866 3-85 8.0 (70) 4236 42A5BEPM-5N 112 (1/6.7) 95 1855 1850 0865 0866 6-172 4.5 (40) N4235 42A5BEPM-5N 112 (1/6.7) 95 1855 1850 0865 0866 1.3-36 14.2 (126) 4299 42A7BEPM-5H 141 (1/5) 96 1855 1850 0865 0866 3.3-96 9.2 (81) N4296 42A7BEPM-5H 141 (1/5) 96 1855 1850 0865 0866 INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 99

CONTOLS & ACCESSOIES FO INTENATIONAL PODUCTS A Ceiling Mount Sidewall Mount Base Mount Most parallel shaft stock gearmotors have a breather hole on top and require that the driveshaft remain at 12 o clock position with respect to the horizon. See Mounting positions on page 4. ITEMS FO TYPE FPM CONTOLS Item Model No. Accessory Description 0888 0889 A 1890 0893 0895 Analog Interface Board for use with Control model 1850 Allows control to accept a variable voltage or current signal from user s host controller in order to automatically control motor speed. Inputs are optically isolated. Digital Interface Board for use with Control model 1850. Allows control to accept 8 parallel TTL signals from user s host controller in order to automatically control motor speed. Inputs are optically isolated. Electronic Direction & Braking Board for use with Control model 1850. Allows user to change motor direction and to dynamically brake motor to a quick stop. Inputs are not optically isolated. Local/emote Switch for use with Control model 1850 when used with Accessory Models 1888 and 1889.Allows user to switch between automatic and manual operation. Sealing Kit for use with model 1855 in order to upgrade from the standard IP-40 (NEMA 1) enclosure to IP 44 (NEMA 4). MOTO AND GEAMOTO L BACKETS Deflection Model No. Motor Type kg (lbs.) N (lbs.) 0990 Kit for 24A.45 (1) 111 (25) 1968 Kit for 32A,24A-D, 24A-Z, 32A-Z, 30-D.57 (1.3) 222 (50) 1970 Kit for 32A-W,34-W.8 (1.8) 556 (125) 1969 Kit for 42A-E,42A-F, 42-E 1.1 (2.4) 890 (200) None Kit for 34.57 (1.3) 222 (50) None Kit for 34-Z.68 (1.5) 445 (100) A C B D OTHE MOTO AND GEAMOTO KITS Item Model No Description kgs. (lbs.) A 1971 Base Mounting Kit for Metric 3F Gearmotors 1.1 (1/2) B 0982 Steel Terminal Box Kit for 42 Motors and Gearmotors.9 (2) C 1982 Die cast terminal box kit for 30 motors and gearmotors.45 (1) D 1984 Die Cast Terminal Box Kit with terminal block for Metric 32A, 34, 42A, and 42, Motors and Gearmotors.45 (1) E 0991 Die Cast Base Kit for 42A Motors.1 (.3) F 0992 Adaptor Plate.45 (1) CAPACITOS See page 30 for oil and metalized mylar capacitors dimensions. E F 100