DYNA-DRIVE GROUND-DRIVEN CULTIVATOR Rev 02-07 DD 60 S/N 10095 -CURRENT Part No. 00771093P PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W (800-446-5158) to obtain a Free copy before operating the equipment. M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261 2007 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
Parts Section 1 PARTS SECTION
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4561 2007 Alamo Group Inc. Parts Section 2
PART NAME INDEX CRUMBLER 2000, 2600, 3000 Rev 04-04... 48 CRUMBLER 2400, 3000, 3400 Rev 04-04... 50 CRUMBLER 3000 Rev 04-04... 46 CRUMBLER 4000-5000... 52, 54, 56 CRUMBLER 6000 Rev 04-04... 58, 60 GREASE LINES AND SHIELDS - MODEL 6000... 67 LIGHT KIT - MODEL 4000, 5000 & 6000... 64 MODEL 2000 MAINFRAME... 4 MODEL 2400 MAINFRAME... 6 MODEL 2600 MAINFRAME... 8 MODEL 3000 MAINFRAME... 10, 12 MODEL 3400 MAINFRAME... 14 MODEL 4000 MAINFRAME... 16, 18 MODEL 5000 MAINFRAME... 20, 22 MODEL 6000 MAINFRAME Pub 08-06... 24 REAR FLAP - MODEL 4000 & 5000... 62 REAR FLAP - MODEL 6000... 63 SIGNAL LAMPS - DUAL (AMBER)... 65 SIGNAL LAMPS - DUAL (RED)... 66 TRANSMISSION ASSEMBLY... 28 TRANSMISSION ASSEMBLY Pub 08-06... 26 TRIPLEX DRIVE TRANSMISSION ASSY 6000 S/N 10095 -Current Pub 08-06... 68 2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07... 34 2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIESRev 02-07... 32 2400, 3000, 3400 ROTOR SHAFT& BEARING ASSEMBLIES... 36 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07... 30 4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLIES... 42 4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07... 38, 40 6000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07... 44 2007 Alamo Group Inc. Parts Section 3
MODEL 2000 MAINFRAME 2007 Alamo Group Inc. Parts Section 4
MODEL 2000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 1 852071 1 MAINFRAME 2000 2 552010 4 PIN 3 852017 12 BRACKET - HINGE 4 201143 24 COACH BOLT 00754583 24 FLAT WASHER 00765676 24 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852054 1 GUARD - HINGED FLAP 6 06.012.03 2 LINK - FLAP ADJUSTMENT 215046 4 PIN.HAIR 7 2196 2 CLIP 552263 2 PIN, HITCH 16 3834200 1 SKID 8277 4 PLOW BOLT 00013901 4 NUT 214124 4 WASHER 17 277476 1 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 3830209 1 PLATE - DEPTH ADJUST LH 3830208 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 22 3832030 2 PLATE - REFLECTOR MTG. 2007 Alamo Group Inc. Parts Section 5
MODEL 2400 MAINFRAME 2007 Alamo Group Inc. Parts Section 6
MODEL 2400 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 1 852071 1 MAINFRAME 2400 2 552010 4 PIN 3 852017 12 BRACKET - HINGE 4 201143 24 COACH BOLT 00754583 24 FLAT WASHER 00765676 24 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852054 1 GUARD - HINGED FLAP 6 552039 2 LINK - FLAP ADJUSTMENT 215046 4 PIN.HAIR 7 2196 2 CLIP 552263 2 PIN, HITCH 16 552007 1 SKID 8277 4 PLOW BOLT 00013901 4 NUT 214124 4 WASHER 17 277476 1 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 852020 1 PLATE - DEPTH ADJUST LH 852021 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 2007 Alamo Group Inc. Parts Section 7
MODEL 2600 MAINFRAME 2007 Alamo Group Inc. Parts Section 8
MODEL 2600 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 2 552010 5 PIN 3 852017 15 BRACKET - HINGE 4 201143 30 COACH BOLT 00754583 30 FLAT WASHER 00765676 30 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852055 1 GUARD - HINGED FLAP 6 06.012.03 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 7 2196 2 CLIP 552263 2 PIN, HITCH 12 852072 1 MAINFRAME 2600 16 3834200 1 SKID 8277 4 PLOW BOLT 00013901 4 NUT 214124 4 WASHER 17 277476 1 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 3830209 1 PLATE - DEPTH ADJUST LH 3830208 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 22 3832030 2 PLATE - REFLECTOR MTG. 2007 Alamo Group Inc. Parts Section 9
MODEL 3000 MAINFRAME 2007 Alamo Group Inc. Parts Section 10
MODEL 3000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 1 852069 1 MAINFRAME 3000 2 552010 6 PIN 3 852017 18 BRACKET - HINGE 4 201143 36 COACH BOLT 00754583 36 FLAT WASHER 00765676 36 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852040 1 GUARD - HINGED FLAP 6 06.012.03 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 7 2196 2 CLIP 3830219 2 PIN, HITCH (CAT II, CAT III) 3834855 2 SPACER, HITCH 3834854 2 SPACER, HITCH 9 2196 1 CLIP 3830251 1 PIN, TOP LINK CAT II 10 2196 1 CLIP 3830252 1 PIN, TOP LINK CAT III 16 3834200 1 SKID 8277 4 PLOW BOLT 00013901 4 NUT 214124 4 WASHER 17 277476 1 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 3830209 1 PLATE - DEPTH ADJUST LH 3830208 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 22 3832030 2 PLATE - REFLECTOR MTG. 23 2438621 1 SPADE - SMV 24 00021400 2 BOLT 25 32901C 2 LOCKNUT 2007 Alamo Group Inc. Parts Section 11
MODEL 3000 MAINFRAME 2007 Alamo Group Inc. Parts Section 12
MODEL 3000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 2 552010 5 PIN 3 852017 15 BRACKET - HINGE 4 201143 30 COACH BOLT 00754583 30 FLAT WASHER 00765676 30 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852055 1 GUARD - HINGED FLAP 6 552039 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 7 2196 2 CLIP 552263 2 PIN, HITCH 12 852072 1 MAINFRAME 3000 16 552007 1 SKID 8277 4 PLOW BOLT 00013901 4 NUT 214124 4 WASHER 17 277476 1 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 852020 1 PLATE - DEPTH ADJUST LH 852021 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 2007 Alamo Group Inc. Parts Section 13
MODEL 3400 MAINFRAME 2007 Alamo Group Inc. Parts Section 14
MODEL 3400 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 1 852069 1 MAINFRAME 3400 2 552010 6 PIN 3 852017 18 BRACKET - HINGE 4 201143 36 COACH BOLT 00754583 36 FLAT WASHER 00765676 36 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852040 1 GUARD - HINGED FLAP 6 552039 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 7 2196 2 CLIP 552257 2 PIN, HITCH (CAT II, CAT III) 552258 2 SPACER 9 2196 1 CLIP 3830251 1 PIN, TOP LINK PIN CAT II 10 2196 1 CLIP 3830252 1 PIN, TOP LINK PIN CAT III 16 552007 1 SKID 8277 4 PLOW BOLT 00013901 4 NUT 214124 4 WASHER 17 277476 1 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 852020 1 PLATE - DEPTH ADJUST LH 852021 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 2007 Alamo Group Inc. Parts Section 15
MODEL 4000 MAINFRAME 2007 Alamo Group Inc. Parts Section 16
MODEL 4000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 2 552010 7 PIN 3 852017 21 BRACKET - HINGE 4 201143 42 COACH BOLT 00754583 42 FLAT WASHER 00765676 42 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852086 1 GUARD - HINGED FLAP 6 06.012.03 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 10 2196 1 CLIP 3830270 1 TOP LINK PIN - CAT III 12 852087 1 MAINFRAME 4000 13 0838404 2 KLICK PIN 3830271 2 PIN, LOWER LINK - CAT III S/N 10725 AND AFTER 3830210 2 PIN, HITCH - CAT III S/N 10700-10724 3834854 2 SPACER 16 3834200 2 SKID 8277 8 PLOW BOLT 00013901 8 NUT 214124 8 WASHER 17 277476 2 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 19 852008 1 CHAINCASE RH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 3830209 1 PLATE-DEPTH ADJUST LH 3830208 1 PLATE-DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 23 2438621 1 SPADE, SMV 24 00021400 2 BOLT 25 32901C 2 LOCKNUT 2007 Alamo Group Inc. Parts Section 17
MODEL 4000 MAINFRAME 2007 Alamo Group Inc. Parts Section 18
MODEL 4000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 2 552010 7 PIN 3 852017 21 BRACKET - HINGE 4 201143 42 COACH BOLT 00754583 42 FLAT WASHER 00765676 42 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 852086 1 GUARD - HINGED FLAP 6 552039 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 9 2196 1 CLIP 852032 1 PIN, HITCH 10 2196 1 CLIP 852033 1 PIN, HITCH 12 852087 1 MAINFRAME 4000 13 2196 2 CLIP 552257 2 PIN, HITCH - CAT II, III 552258 2 SPACER 16 552007 2 SKID 8277 8 PLOW BOLT 00013901 8 NUT 214124 8 WASHER 17 277476 2 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 19 852008 1 CHAINCASE RH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 852020 1 PLATE-DEPTH ADJUST LH 852021 1 PLATE-DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 2007 Alamo Group Inc. Parts Section 19
MODEL 5000 MAINFRAME 2007 Alamo Group Inc. Parts Section 20
MODEL 5000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 2 552010 10 PIN 3 852017 30 BRACKET - HINGE 4 201143 60 COACH BOLT 00754583 60 FLAT WASHER 00765676 60 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 06.773.01 1 GUARD - HINGED FLAP 6 06.012.03 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 10 2196 1 CLIP 3830270 1 TOP LINK PIN CAT III 12 3830205 1 MAINFRAME 5000 13 0838404 2 KLICK PIN 3830271 2 PIN, LOWER LINK CAT III S/N 10742 AND AFTER 3830210 2 PIN, HITCH - CAT III S/N 10700-10741 3834854 2 SPACER 16 3834200 2 SKID 8277 8 PLOW BOLT 00013901 8 NUT 214124 8 WASHER 17 277476 2 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 19 852008 1 CHAINCASE RH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 3830209 1 PLATE - DEPTH ADJUST LH 3830208 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 23 2438621 1 SPADE, SMV 24 00021400 2 BOLT 25 32901C 2 LOCKNUT 2007 Alamo Group Inc. Parts Section 21
MODEL 5000 MAINFRAME 2007 Alamo Group Inc. Parts Section 22
MODEL 5000 MAINFRAME ITEM PART NO. QTY. DESCRIPTION 2 552010 8 PIN 3 852017 24 BRACKET - HINGE 4 201143 48 COACH BOLT 00754583 48 FLAT WASHER 00765676 48 SELF-LOCKING NUT 5 215046 4 HAIR COTTER PIN 5A 852061 1 GUARD - HINGED FLAP LH 5B 852060 1 GUARD - HINGED FLAP RH 6 552039 2 LINK - FLAP ADJUSTMENT 215046 4 PIN, HAIR 9 2196 1 CLIP 852032 1 PIN, HITCH 10 2196 1 CLIP 852033 1 PIN, HITCH 12 852070 1 MAINFRAME 5000 13 2196 2 CLIP 552257 2 PIN, HITCH - CAT II, III 552258 2 SPACER 14 552293 1 SUPPORT, HINGE FLAP 00751688 6 BOLT 00754577 6 LOCKWASHER 00755949 6 NUT 16 552007 2 SKID 8277 8 PLOW BOLT 00013901 8 NUT 214124 8 WASHER 17 277476 2 FILLER CAP 18 852006 1 CHAINCASE LH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 19 852008 1 CHAINCASE RH 00762395 9 BOLT 00756026 7 BOLT 9100206 9 SPRING WASHER 00756164 7 LOCKING NUT 20 852020 1 PLATE - DEPTH ADJUST LH 852021 1 PLATE - DEPTH ADJUST RH 21 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 2007 Alamo Group Inc. Parts Section 23
MODEL 6000 MAINFRAME Pub 08-06 2007 Alamo Group Inc. Parts Section 24
MODEL 6000 MAINFRAME Pub 08-06 ITEM PART NO. QTY. DESCRIPTION 1 3830245 1 GUARD - RIGHT REAR HINGED FLAP 2 3830254 1 GUARD - LEFT REAR HINGED FLAP 3 852017 30 BRACKET - HINGE 201143 60 CARRIAGE BOLT 00754583 60 FLATWASHER 00765676 60 TOP LOCKNUT 4 552010 10 PIN 5 3831045 4 BAR - LINK 215046 8 HAIRPIN COTTER 6 3834200 2 SKID (7.00" WIDE) 3834201 2 SKID (8.34" WIDE) 8277 8 PLOW BOLT 00013901 8 NUT 214124 8 WASHER 7 852006 1 CHAINCASE - LH (4.84" WIDE) 3830291 1 CHAINCASE - LH (6.18" WIDE) 8 277476 2 FILLER CAP 9 852008 1 CHAINCASE - RH (4.84" WIDE) 3830290 1 CHAINCASE - RH (6.18" WIDE) 00762395 18 BOLT 00756026 14 BOLT 9100206 18 SPRING WASHER 00756164 14 LOCKING NUT 10 3830271 2 PIN - LOWER HITCH (CAT III) 11 3834854 2 SPACER 12 00725708 2 PIN - SNAPPER 13 3830270 1 PIN - UPPER LINK (CAT III) 14 2196 1 PIN - CLIP 15 3830247 1 MAINFRAME 16 00021400 2 BOLT 17 2438621 1 SPADE SMV 18 32901C 2 LOCKNUT 2007 Alamo Group Inc. Parts Section 25
TRANSMISSION ASSEMBLY Pub 08-06 2007 Alamo Group Inc. Parts Section 26
TRANSMISSION ASSEMBLY Pub 08-06 ITEM PART NO. 2000 26000 3000 QTY 4000 5000 6000 QTY DESCRIPTION 1 552004 1 2 CHAIN - ROLLER 2 241705 1 2 SPROCKET 3 552214 1 2 WASHER 00756373 1 2 BOLT 701615C 1 2 SPRING WASHER 4 04.278.02 1 2 SPROCKET 5 552215 1 2 WASHER 00756373 1 2 BOLT 701615C 1 2 SPRING WASHER 11 08.816.01 1 1 TENSIONER BRACKET - LH 08.816.02-1 TENSIONER BRACKET - RH 14 852007 1 2 ROD-SPRING GUIDE 212419 2 4 LOCKING NUT 15 552008 1 2 SPECIAL NUT 16 214226 1 2 FLAT WASHER 17 225092 1 2 SPRING - COMP 18 852081 1 2 BRACKET - TENSIONER 19 552279 2 4 PLATE - NYLON GUIDE 00765676 2 4 SELF-LOCKING NUT 00766178 2 4 BOLT 22 214226 1 2 FLAT WASHER 23 0401225 1 2 CIRCLIP 24 552009 1 2 PIN 25 214224 1 2 WASHER 9313056 1 2 BOLT 9100206 1 2 SPRING WASHER 2007 Alamo Group Inc. Parts Section 27
TRANSMISSION ASSEMBLY 2007 Alamo Group Inc. Parts Section 28
TRANSMISSION ASSEMBLY ITEM PART NO. 2400 3000 3400 QTY 4000 5000 QTY DESCRIPTION 1 552004 1 2 CHAIN - ROLLER 2 241705 1 2 SPROCKET 3 552214 1 2 WASHER 00756373 1 2 BOLT 701615C 1 2 SPRING WASHER 4 241706 1 2 SPROCKET 5 552215 1 2 WASHER 00756373 1 2 BOLT 701615C 1 2 SPRING WASHER 6 852079 1 1 BRACKET, CHAIN STOP LH 852080-1 BRACKET, CHAIN STOP RH 7 552116 1 2 PIN IDLER 9313056 1 2 BOLT 9100206 1 2 SPRING WASHER 8 241707 1 2 SPROCKET 9 552021 1 2 SPACER, BEARING 10 221036 2 4 COLLAR, SPACER 11 852031 1 2 BRACKET, CUSHION ARM 12 243685 2 4 BEARING 13 552213 1 2 WASHER 14 852007 1 2 ROD-SPRING GUIDE 212419 2 4 LOCKING NUT 15 552008 1 2 SPECIAL NUT 16 214226 1 2 FLAT WASHER 17 225092 1 2 SPRING - COMP 18 852081 1 2 BRACKET - TENSIONER 19 552279 2 4 PLATE - NYLON GUIDE 00765676 2 4 SELF-LOCKING NUT 00766178 2 4 BOLT 22 214226 1 2 FLAT WASHER 23 0401225 1 2 CIRCLIP 24 552009 1 2 PIN 25 214224 1 2 WASHER 9313056 1 2 BOLT 9100206 1 2 SPRING WASHER 26 852014 1 2 BRACKET SPRING MOUNT LH 00762401 2 4 BOLT 00756164 2 4 LOCKING NUT 27 852015 1 2 BRACKET SPRING MOUNT RH 00762401 2 4 BOLT 00756164 2 4 LOCKING NUT 28 552020 1 2 PLATE SPRING MTG. 00756026 4 8 BOLT 00756164 4 8 LOCKING NUT 29 277474 1 2 RUBBER BUFFER 00756164 1 2 LOCKING NUT 2007 Alamo Group Inc. Parts Section 29
3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07 2007 Alamo Group Inc. Parts Section 30
3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07 ITEM PART NO. QTY. DESCRIPTION 1 552015 1 SPACER 2 852038 1 ROTOR SHAFT - FRONT 3 06.949.01 92 TINE - CLOCKWISE TWIST 9100206 92 SPRING WASHER 202851 92 BOLT 00756105 92 LOCKING NUT 4 06.949.02 92 TINE - COUNTERCLOCKWISE TWIST 9100206 92 SPRING WASHER 202851 92 BOLT 00756105 92 LOCKING NUT 5 06.950.01 64 PLATE - TINE SPACER 9100206 64 SPRING WASHER 202851 64 BOLT 00756105 64 LOCKING NUT 6 852039 1 ROTOR SHAFT - REAR 7 552117 1 COLLAR 20 221035 2 COLLAR 22 223051 2 SEAL 23 222156 4 SNAP RING 24 852049 2 HOUSING - BEARING 00766457 2 GREASE FITTING (METRIC) 00003500 2 GREASE FITTING (NPT) 25 243687 2 BEARING 26 3830213 1 PLATE STRUT 00756373 4 BOLT 9143007 8 LOCKING NUT 00765901 3 BOLT 28 243683 2 BEARING ASSEMBLY- FLANGED 02957275 8 BOLT 9143007 8 LOCKING NUT 29 852022 2 DUST COVER 30 3836800 2 SEAL 10 41895.01 15 TINE - CLEARING LH - LONG 9100206 15 SPRING WASHER 202851 15 BOLT 00756105 15 LOCKING NUT 11 41895.02 15 TINE - CLEARING RH - LONG 9100206 15 SPRING WASHER 202851 15 BOLT 00756105 15 LOCKING NUT 2007 Alamo Group Inc. Parts Section 31
2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIESRev 02-07 2007 Alamo Group Inc. Parts Section 32
2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIESRev 02-07 ITEM PART NO. 2000 QTY 2600 QTY 3000 QTY DESCRIPTION 1 552015 1 1 1 SPACER 2 852051 1 - - ROTOR SHAFT - FRONT (2000 UNIT) 852050-1 - ROTOR SHAFT - FRONT (2600 UNIT) 852038 - - 1 ROTOR SHAFT - FRONT (3000 UNIT) 3 06.949.01 62 80 92 TINE - CLOCKWISE TWIST 9100206 62 80 92 SPRING WASHER 202851 62 80 92 BOLT 00756105 62 80 92 LOCKING NUT 4 06.949.02 62 80 92 TINE - COUNTERCLOCKWISE TWIST 9100206 62 80 92 SPRING WASHER 202851 62 80 92 BOLT 00756105 62 80 92 LOCKING NUT 5 06.950.01 44 56 64 PLATE - TINE SPACER 9100206 44 56 64 SPRING WASHER 202851 44 56 64 BOLT 00756105 44 56 64 LOCKING NUT 6 852053 1 - - ROTOR SHAFT - REAR (2000 UNIT) 852052-1 - ROTOR SHAFT - REAR (2600 UNIT) 852039 - - 1 ROTOR SHAFT - REAR (3000 UNIT) 7 552117 1 1 1 COLLER 10 41895.01 10 13 15 TINE - CLEARING LH - LONG 9100206 10 13 15 SPRING WASHER 202851 10 13 15 BOLT 00756105 10 13 15 LOCKING NUT 11 41895.02 10 13 15 TINE - CLEARING RH - LONG 9100206 10 13 15 SPRING WASHER 202851 10 13 15 BOLT 00756105 10 13 15 LOCKING NUT 20 221035 4 4 4 COLLAR 22 223051 2 2 2 SEAL 23 222156 4 4 4 SNAP RING 24 852049 2 2 2 HOUSING - BEARING 00003500 2 2 2 GREASE FITTING 25 243687 2 2 2 BEARING 26 3830213 1 1 1 PLATE STRUT 00756373 4 4 4 BOLT 9143007 8 8 8 LOCKING NUT 00765901 3 3 3 BOLT 28 243683 2 2 2 BEARING ASSEMBLY- FLANGED 02957275 8 8 8 BOLT 9143007 8 8 8 LOCKING NUT 29 852022 2 2 2 DUST COVER 2007 Alamo Group Inc. Parts Section 33
2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07 2007 Alamo Group Inc. Parts Section 34
2000, 2600, 3000 ROTOR SHAFT& BEARING ASSEMBLIES Rev 02-07 ITEM PART NO. 2000 QTY 2600 QTY 3000 QTY DESCRIPTION 1 552015 1 1 1 SPACER 2 852051 1 - - ROTOR SHAFT - FRONT (2000 UNIT) 852050-1 - ROTOR SHAFT - FRONT (2600 UNIT) 852038 - - 1 ROTOR SHAFT - FRONT (3000 UNIT) 3 06.949.01 62 80 92 TINE - CLOCKWISE TWIST 9100206 62 80 92 SPRING WASHER 202851 62 80 92 BOLT 00756105 62 80 92 LOCKING NUT 4 06.949.02 62 80 92 TINE - COUNTERCLOCKWISE TWIST 9100206 62 80 92 SPRING WASHER 202851 62 80 92 BOLT 00756105 62 80 92 LOCKING NUT 5 06.950.01 44 56 64 PLATE - TINE SPACER 9100206 44 56 64 SPRING WASHER 202851 44 56 64 BOLT 00756105 44 56 64 LOCKING NUT 6 852053 1 - - ROTOR SHAFT - REAR (2000 UNIT) 852052-1 - ROTOR SHAFT - REAR (2600 UNIT) 852039 - - 1 ROTOR SHAFT - REAR (3000 UNIT) 7 552117 1 1 1 COLLAR 10 41895.01 10 13 15 TINE - CLEARING LH - LONG 9100206 10 13 15 SPRING WASHER 202851 10 13 15 BOLT 00756105 10 13 15 LOCKING NUT 11 41895.02 10 13 15 TINE - CLEARING RH - LONG 9100206 10 13 15 SPRING WASHER 202851 10 13 15 BOLT 00756105 10 13 15 LOCKING NUT 20 221035 2 2 2 COLLAR 22 223051 4 4 4 SEAL 23 222156 4 4 4 SNAP RING 24 852049 2 2 2 HOUSING - BEARING 00003500 2 2 2 GREASE FITTING 25 243687 2 2 2 BEARING 26 3830213 1 1 1 PLATE STRUT 00756373 4 4 4 BOLT 9143007 8 8 8 LOCKING NUT 00765901 3 3 3 BOLT 28 243683 2 2 2 BEARING ASSEMBLY- FLANGED 02957275 8 8 8 BOLT 9143007 8 8 8 LOCKING NUT 29 852022 2 2 2 DUST COVER 2007 Alamo Group Inc. Parts Section 35
2400, 3000, 3400 ROTOR SHAFT& BEARING ASSEMBLIES 2007 Alamo Group Inc. Parts Section 36
2400, 3000, 3400 ROTOR SHAFT& BEARING ASSEMBLIES ITEM PART NO. 2400 QTY 3000 QTY 3400 QTY DESCRIPTION 1 552015 1 1 1 SPACER 2 852051 1 - - ROTOR SHAFT - FRONT (2400 UNIT) 852050-1 - ROTOR SHAFT - FRONT (3000 UNIT) 852038 - - 1 ROTOR SHAFT - FRONT (3400 UNIT) 3 552001 62 80 92 TINE - CLOCKWISE TWIST 9100206 62 80 92 SPRING WASHER 202851 62 80 92 BOLT 00756105 62 80 92 LOCKING NUT 4 552002 62 80 92 TINE - COUNTERCLOCKWISE TWIST 9100206 62 80 92 SPRING WASHER 202851 62 80 92 BOLT 00756105 62 80 92 LOCKING NUT 5 552016 44 56 64 PLATE - TINE SPACER 9100206 44 56 64 SPRING WASHER 202851 44 56 64 BOLT 00756105 44 56 64 LOCKING NUT 6 852053 1 - - ROTOR SHAFT - REAR (2400 UNIT) 852052-1 - ROTOR SHAFT - REAR (3000 UNIT) 852039 - - 1 ROTOR SHAFT - REAR (3400 UNIT) 7 552117 1 1 1 COLLAR 10 552005 10 13 15 TINE - CLEARING LH - LONG 9100206 10 13 15 SPRING WASHER 202851 10 13 15 BOLT 00756105 10 13 15 LOCKING NUT 11 552006 10 13 15 TINE - CLEARING RH - LONG 9100206 10 13 15 SPRING WASHER 202851 10 13 15 BOLT 00756105 10 13 15 LOCKING NUT 20 221035 2 2 2 COLLAR 22 223051 - - - SEAL 23 222156 - - - SNAP RING 24 852049 - - - HOUSING - BEARING 00003500 - - - GREASE FITTING 25 243687 - - - BEARING 26 852078 1 1 1 STRUT-BRG HOUSING (BOLT ON) 00756373 4 4 4 BOLT 9143007 8 8 8 LOCKING NUT 00765901 3 3 3 BOLT 28 243683 2 2 2 BEARING ASSEMBLY- FLANGED 02957275 8 8 8 BOLT 9143007 8 8 8 LOCKING NUT 29 852022 2 2 2 DUST COVER 2007 Alamo Group Inc. Parts Section 37
4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 2007 Alamo Group Inc. Parts Section 38
4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 ITEM PART NO. 4000 QTY 5000 QTY DESCRIPTION 1 552015 2 2 SPACER 2 852084 2 - ROTOR SHAFT - FRONT (4000 UNIT ONLY) 3830200-1 ROTOR SHAFT - FRONT RH (5000 UNIT ONLY) 852063-1 ROTOR SHAFT - FRONT LH (5000 UNIT ONLY) 3 06.949.01 122 152 TINE - CLOCKWISE TWIST 9100206 122 152 SPRING WASHER 202851 122 152 BOLT 00756105 122 152 LOCKING NUT 4 06.949.02 122 152 TINE - COUNTERCLOCKWISE TWIST 9100206 122 152 SPRING WASHER 202851 122 152 BOLT 00756105 122 152 LOCKING NUT 5 06.950.01 84 104 PLATE - TINE SPACER 9100206 84 104 SPRING WASHER 202851 84 104 BOLT 00756105 84 104 LOCKING NUT 6 852083 1 - ROTOR SHAFT - REAR RH (4000 UNIT ONLY) 852082 1 - ROTOR SHAFT - REAR LH (4000 UNIT ONLY) 3830201-2 ROTOR SHAFT - REAR (5000 UNIT ONLY) 7 552117 2 2 COLLAR 20 221035 4 4 COLLAR 22 223051 4 4 SEAL 23 222156 8 8 SNAP RING 24 852049 4 4 HOUSING - BEARING 00766457 4 4 GREASE FITTING (METRIC) 00003500 4 4 GREASE FITTING (NPT) 25 243687 4 4 BEARING 26 3830213 2 2 PLATE STRUT 00756373 8 8 BOLT 9143007 16 16 LOCKING NUT 00765901 6 6 BOLT 28 852067 4 4 BEARING HOUSING ASSY (INC 29,30) 9313087 8 8 BOLT 9143007 8 8 LOCKING NUT 29 852003 4 4 BEARING HOUSING 9313056 8 8 BOLT 9100206 8 8 SPRING WASHER 00766457 4 4 GREASE NIPPLE 30 552081 4 4 BEARING ASSEMBLY 31 3836800 4 4 SEAL IF EQUIPED WITH WITH CLEARING TINES: 10 41895.01 20 25 TINE - CLEARING LH - LONG 9100206 20 25 SPRING WASHER 202851 20 25 BOLT 00756105 20 25 LOCKING NUT 11 41895.02 20 25 TINE - CLEARING RH - LONG 9100206 20 25 SPRING WASHER 202851 20 25 BOLT 00756105 20 25 LOCKING NUT 2007 Alamo Group Inc. Parts Section 39
4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 2007 Alamo Group Inc. Parts Section 40
4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 ITEM PART NO. 4000 QTY 5000 QTY DESCRIPTION 1 552015 2 2 SPACER 2 852084 2 - ROTOR SHAFT - FRONT (4000 UNIT ONLY) 3830200-1 ROTOR SHAFT - FRONT RH (5000 UNIT ONLY) 852063-1 ROTOR SHAFT - FRONT LH (5000 UNIT ONLY) 3 06.949.01 122 152 TINE - CLOCKWISE TWIST 9100206 122 152 SPRING WASHER 202851 122 152 BOLT 00756105 122 152 LOCKING NUT 4 06.949.02 122 152 TINE - COUNTERCLOCKWISE TWIST 9100206 122 152 SPRING WASHER 202851 122 152 BOLT 00756105 122 152 LOCKING NUT 5 06.950.01 84 104 PLATE - TINE SPACER 9100206 84 104 SPRING WASHER 202851 84 104 BOLT 00756105 84 104 LOCKING NUT 6 852083 1 - ROTOR SHAFT - REAR RH (4000 UNIT ONLY) 852082 1 - ROTOR SHAFT - REAR LH (4000 UNIT ONLY) 3830201-2 ROTOR SHAFT - REAR (5000 UNIT ONLY) 7 552117 2 2 COLLAR 10 41895.01 20 25 TINE - CLEARING LH - LONG 9100206 20 25 SPRING WASHER 202851 20 25 BOLT 00756105 20 25 LOCKING NUT 11 41895.02 20 25 TINE - CLEARING RH - LONG 9100206 20 25 SPRING WASHER 202851 20 25 BOLT 00756105 20 25 LOCKING NUT 20 221035 4 4 COLLAR 22 223051 8 8 SEAL 23 222156 8 8 SNAP RING 24 852049 4 4 HOUSING - BEARING 00003500 4 4 GREASE FITTING 25 243687 4 4 BEARING 26 3830213 2 2 PLATE STRUT 00756373 8 8 BOLT 9143007 16 16 LOCKING NUT 00765901 6 6 BOLT 28 852067 4 4 BEARING HOUSING ASSY (INC 29,30) 9313087 8 8 BOLT 9143007 8 8 LOCKING NUT 29 852003 4 4 BEARING HOUSING 9313056 8 8 BOLT 9100206 8 8 SPRING WASHER 00766457 4 4 GREASE NIPPLE 30 552081 4 4 BEARING ASSEMBLY 2007 Alamo Group Inc. Parts Section 41
4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLIES 2007 Alamo Group Inc. Parts Section 42
4000 & 5000 ROTOR SHAFT & BEARING ASSEMBLIES ITEM PART NO. 4000 QTY 5000 QTY DESCRIPTION 1 552015 2 2 SPACER 2 852084 2 - ROTOR SHAFT - FRONT (4000 UNIT ONLY) 852062-1 ROTOR SHAFT - FRONT LH (5000 UNIT ONLY) 852063-1 ROTOR SHAFT - FRONT RH (5000 UNIT ONLY) 3 552001 122 140 TINE - CLOCKWISE TWIST 9100206 122 140 SPRING WASHER 202851 122 140 BOLT 00756501 122 140 LOCKING NUT 4 552002 122 140 TINE - COUNTERCLOCKWISE TWIST 9100206 122 140 SPRING WASHER 202851 122 140 BOLT 00756501 122 140 LOCKING NUT 5 552016 84 96 PLATE - TINE SPACER 9100206 84 96 SPRING WASHER 202851 84 96 BOLT 00756501 84 96 LOCKING NUT 6 852083 1 - ROTOR SHAFT - REAR RH (4000 UNIT ONLY) 852082 1 - ROTOR SHAFT - REAR LH (4000 UNIT ONLY) 852064-2 ROTOR SHAFT - REAR (5000 UNIT ONLY) 7 552117 2 2 COLLAR 10 552005 20 23 TINE - CLEARING LH - LONG 9100206 20 23 SPRING WASHER 202851 20 23 BOLT 00756501 20 23 LOCKING NUT 11 552006 20 23 TINE - CLEARING RH - LONG 9100206 20 23 SPRING WASHER 202851 20 23 BOLT 00756501 20 23 LOCKING NUT 20 221035 4 4 COLLAR 22 223051 - - SEAL 23 222156 - - SNAP RING 24 852049 - - HOUSING - BEARING 00003500 - - GREASE FITTING 25 243687 - - BEARING 26 852078 2 2 STRUT-BRG HOUSING (BOLT ON) 00756373 8 8 BOLT 9143007 16 16 LOCKING NUT 00765901 6 6 BOLT 28 852067 4 4 BEARING HOUSING ASSY (INC 29,30) 9313087 8 8 BOLT 9143007 8 8 LOCKING NUT 29 852003 4 4 BEARING HOUSING 9313056 8 8 BOLT 9100206 8 8 SPRING WASHER 00766457 4 4 GREASE NIPPLE 30 552081 4 4 BEARING ASSEMBLY 2007 Alamo Group Inc. Parts Section 43
6000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 2007 Alamo Group Inc. Parts Section 44
6000 ROTOR SHAFT & BEARING ASSEMBLY Rev 02-07 ITEM PART NO. QTY. DESCRIPTION 1 552015 2 SPACER 2 3830227 1 ROTOR SHAFT - FRONT RH WITH DUPLEX DRIVE ON SHORT SHAFT * 3830301 1 ROTOR SHAFT FRONT RH WITH TRIPLEX DRIVE 3830228 1 ROTOR SHAFT - FRONT LH WITH DUPLEX DRIVE ON SHORT SHAFT * 3830302 1 ROTOR SHAFT FRONT LH WITH TRIPLEX DRIVE 3 06.949.01 174 TINE - CLOCKWISE TWIST 9100206 176 SPRING WASHER 202851 176 BOLT 00756105 176 LOCKING NUT 4 06.949.02 176 TINE - COUNTERCLOCKWISE TWIST 9100206 176 SPRING WASHER 202851 176 BOLT 00756105 176 LOCKING NUT 5 06.950.01 120 PLATE - TINE SPACER 9100206 120 SPRING WASHER 202851 120 BOLT 00756105 120 LOCKING NUT 6 3830226 2 ROTOR SHAFT - REAR WITH DUPLEX DRIVE ON SHORT SHAFT) * 3830303 2 ROTOR SHAFT REAR WITH TRIPLEX DRIVE 7 552117 2 COLLAR 11 41895.02 4 TINE - CLEARING RH - LONG ( LEFT HAND END OF RIGHT HAND REAR ROTAR ONLY) 9100206 4 SPRING WASHER 202851 4 BOLT 00756105 4 LOCKING NUT 20 3832516 8 COLLAR 22 223051 8 SEAL 23 222156 8 SNAP RING 24 852049 4 BEARING HOUSING 00003500 4 GREASE FITTING 25 243687 4 BEARING 26 3830213 2 PLATE STRUT 00756373 8 BOLT 9143007 16 LOCKING NUT 00765901 6 BOLT 28 3830115 4 INNER BEARING HOUSING ASSY (INC 29,30) 9313087 8 BOLT 9143007 8 LOCKING NUT 29 3830284 4 INNER BEARING HOUSING 9313056 8 BOLT 9100206 8 SPRING WASHER 30 552081 4 BEARING ASSEMBLY 31 3838200 4 O-RING IF EQUIPED WITH CLEARING TINES: 10 41895.01 27 TINE,LH CRANK 50 X 351 11 41895.02 27 TINE,RH CRANK 50 X 351 9100206 54 WASHER,LOCK 12MM 202851 54 HHCS M12 X 1.25 X 42 GR.8.8 00756105 54 NUT,TOPLOCK METRIC 12MM-P1.25 * REPLACES SHORT SHAFT IF USING TRIPLEX DRIVE 2007 Alamo Group Inc. Parts Section 45
CRUMBLER 3000 Rev 04-04 2007 Alamo Group Inc. Parts Section 46
CRUMBLER 3000 Rev 04-04 ITEM PART NO. QTY. DESCRIPTION 1 243682 2 BEARING ASSY. - FLANGED W/SHIELDS 3834879 4 SHIELD 02959661 4 BOLT 00762401 4 BOLT 00756164 8 LOCKING NUT 00771054 2 DECAL - GREASE 00766457 2 GREASE FITTING 243689 RP BEARING 3 852011 1 ARM - TRAILING LH 852012 1 ARM - TRAILING RH 4 852029 2 PIN 61368C8 2 BOLT 00755954 2 SPRING WASHER 00754583 2 FLATWASHER 700116C 2 NUT 7 852016 1 CRUMBLER, ROLLER (2000 UNIT) 852023 1 CRUMBLER, ROLLER (2600 UNIT) 852024 1 CRUMBLER, ROLLER (3000 UNIT) 8 852000 2 PIN 214241 2 FLATWASHER 00036900 2 COTTER PIN 212420 2 NUT - SLOTTED 9 00766457 2 FITTING 2007 Alamo Group Inc. Parts Section 47
CRUMBLER 2000, 2600, 3000 Rev 04-04 2007 Alamo Group Inc. Parts Section 48
CRUMBLER 2000, 2600, 3000 Rev 04-04 ITEM PART NO. QTY. DESCRIPTION 1 852013 2 COVER BEARING 02959661 4 BOLT 00762401 4 BOLT 00756164 8 LOCKING NUT 00771054 2 DECAL - GREASE 00766457 2 GREASE FITTING 2 243682 2 BEARING ASSY - FLANGED 243689 RP BEARING 3 852011 1 ARM - TRAILING LH 852012 1 ARM - TRAILING RH 4 852029 2 PIN 61368C8 2 BOLT 00755954 2 SPRING WASHER 00754583 2 FLATWASHER 700116C 2 NUT 7 852016 1 CRUMBLER, ROLLER (2000 UNIT) 852023 1 CRUMBLER, ROLLER (2600 UNIT) 852024 1 CRUMBLER, ROLLER (3000 UNIT) 8 852000 2 PIN 214241 2 FLATWASHER 00036900 2 COTTER PIN 212420 2 NUT - SLOTTED 9 00766457 2 FITTING 2007 Alamo Group Inc. Parts Section 49
CRUMBLER 2400, 3000, 3400 Rev 04-04 2007 Alamo Group Inc. Parts Section 50
CRUMBLER 2400, 3000, 3400 Rev 04-04 ITEM PART NO. QTY. DESCRIPTION 1 852013 2 COVER BEARING 02959661 4 BOLT 00762401 4 BOLT 00756164 8 LOCKING NUT 00771054 2 DECAL - GREASE 00766457 2 GREASE FITTING 2 243682 2 BEARING ASSY - FLANGED 243689 RP BEARING 3 852011 1 ARM - TRAILING LH 852012 1 ARM - TRAILING RH 4 852029 2 PIN 00754764 2 BOLT 00754577 2 SPRING WASHER 00754583 2 FLATWASHER 7 852016 1 CRUMBLER, ROLLER (2400 UNIT) 852023 1 CRUMBLER, ROLLER (3000 UNIT) 852024 1 CRUMBLER, ROLLER (3400 UNIT) 8 852000 2 PIN 214241 2 FLATWASHER 00036900 2 COTTER PIN 212420 2 NUT - SLOTTED 9 00766457 2 FITTING 2007 Alamo Group Inc. Parts Section 51
CRUMBLER 4000-5000 2007 Alamo Group Inc. Parts Section 52
CRUMBLER 4000-5000 ITEM PART NO. QTY. DESCRIPTION 1 243683 2 BEARING ASSY. - FLANGED W/SHIELDS 3834878 4 SHIELD 02957275 8 BOLT 9143007 8 LOCKING NUT 00771054 2 DECAL - GREASE 00766457 2 GREASE FITTING 243690 RP BEARING 3 3830207 1 ARM - TRAILING LH 3830206 1 ARM - TRAILING RH 4 852029 2 PIN 61368C8 2 BOLT 00755954 2 SPRING WASHER 00754583 2 FLATWASHER 700116C 2 NUT 7 3830212 1 CRUMBLER, ROLLER (4000 UNIT) 41.130.01 1 CRUMBLER, ROLLER (5000 UNIT) 8 852058 2 PIN 214241 2 FLATWASHER 00036900 2 COTTER PIN 212420 2 NUT - SLOTTED 9 00766457 2 FITTING 2007 Alamo Group Inc. Parts Section 53
CRUMBLER 4000-5000 2007 Alamo Group Inc. Parts Section 54
CRUMBLER 4000-5000 ITEM PART NO. QTY. DESCRIPTION 1 852059 2 COVER BEARING 02957275 8 BOLT 9143007 8 LOCKING NUT 00771054 2 DECAL - GREASE 00766457 2 GREASE NIPPLE 2 243683 2 BEARING ASSY - FLANGED 243690 RP BEARING 3 3830207 1 ARM - TRAILING LH 3830206 1 ARM - TRAILING RH 4 852029 2 PIN 61368C8 2 BOLT 00755954 2 SPRING WASHER 00754583 2 FLATWASHER 700116C 2 NUT 7 3830212 1 CRUMBLER, ROLLER (4000 UNIT) 41.130.01 1 CRUMBLER, ROLLER (5000 UNIT) 8 852058 2 PIN 214241 2 FLATWASHER 00036900 2 COTTER PIN 212420 2 NUT - SLOTTED 9 00766457 2 FITTING 2007 Alamo Group Inc. Parts Section 55
CRUMBLER 4000-5000 2007 Alamo Group Inc. Parts Section 56
CRUMBLER 4000-5000 ITEM PART NO. QTY. DESCRIPTION 1 852059 2 COVER BEARING 02957275 8 BOLT 9143007 8 LOCKING NUT 00771054 2 DECAL - GREASE 00766457 2 GREASE NIPPLE 2 243683 2 BEARING ASSY - FLANGED 243690 RP BEARING 3 852009 1 ARM - TRAILING LH 852010 1 ARM - TRAILING RH 4 852029 2 PIN 00754764 2 BOLT 00754577 2 SPRING WASHER 00754583 2 FLATWASHER 7 852085 1 CRUMBLER, ROLLER (4000 UNIT) 852026 1 CRUMBLER, ROLLER (5000 UNIT) 8 852058 2 PIN 214241 2 FLATWASHER 00036900 2 COTTER PIN 212420 2 NUT - SLOTTED 9 00766457 2 FITTING 2007 Alamo Group Inc. Parts Section 57
CRUMBLER 6000 Rev 04-04 2007 Alamo Group Inc. Parts Section 58
CRUMBLER 6000 Rev 04-04 ITEM PART NO. QTY. DESCRIPTION 1 243683 4 BEARING ASSY. - FLANGED W/SHIELDS 3834878 8 SHIELD 02957275 16 BOLT 9143007 16 LOCKING NUT 243690 RP BEARING 3 3830207 1 ARM - TRAILING LH 3830206 1 ARM - TRAILING RH (NOT SHOWN) 4 852029 2 PIN 61368C8 3 BOLT 00755954 3 SPRING WASHER 00754583 3 FLATWASHER 700116C 3 NUT 5 3830209 1 PLATE - DEPTH ADJUST LH 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 6 3830237 1 CRUMBLER ROLLER, LH 7 3830236 1 CRUMBLER ROLLER, RH 8 3830238 1 CENTER ARM 9 3830253 1 PIN - CENTER ARM PIVOT 10 3832515 1 BUSHING, THREADED FLANGE 11 3830208 2 PLATE - DEPTH ADJUST RH 12 3832600 1 PIN, HEX ADJUSTMENT 13 701613C 1 LOCKWASHER 14 02959661 1 BOLT 15 3830244 2 COVER 16 212420 3 NUT 00036900 3 COTTER PIN 17 214241 3 FLATWASHER 18 3830239 1 PIN - CENTER ARM 19 852058 2 PIN - OUTER ARM 20 00766457 7 GREASE FITTING 2007 Alamo Group Inc. Parts Section 59
CRUMBLER 6000 Rev 04-04 2007 Alamo Group Inc. Parts Section 60
CRUMBLER 6000 Rev 04-04 ITEM PART NO. QTY. DESCRIPTION 1 852059 2 COVER BEARING 02957275 16 BOLT 9143007 16 LOCKING NUT 2 243683 4 BEARING ASSY - FLANGED 243690 RP BEARING 3 3830207 1 ARM - TRAILING LH 3830206 1 ARM - TRAILING RH (NOT SHOWN) 4 852029 2 PIN 61368C8 3 BOLT 00755954 3 SPRING WASHER 00754583 3 FLATWASHER 700116C 3 NUT 5 3830209 1 PLATE - DEPTH ADJUST LH 214224 2 WASHER 00762395 2 BOLT 9100206 2 SPRING WASHER 6 3830237 1 CRUMBLER ROLLER, LH 7 3830236 1 CRUMBLER ROLLER, RH 8 3830238 1 CENTER ARM 9 3830253 1 PIN - CENTER ARM PIVOT 10 3832515 1 BUSHING, THREADED FLANGE 11 3830208 2 PLATE - DEPTH ADJUST RH 12 3832600 1 PIN, HEX ADJUSTMENT 13 701613C 1 LOCKWASHER 14 02959661 1 BOLT 15 3830244 2 COVER 16 212420 3 NUT 00036900 3 COTTER PIN 17 214241 3 FLATWASHER 18 3830239 1 PIN - CENTER ARM 19 852058 2 PIN - OUTER ARM 20 00766457 7 GREASE FITTING 2007 Alamo Group Inc. Parts Section 61
REAR FLAP - MODEL 4000 & 5000 ITEM PART NO. 4000 QTY 5000 QTY DESCRIPTION 1 00011100 36 38 FLATWASHER 2 00011400 13 13 BOLT 4 3831151 2 - REAR FLAP RETAINING STRAP 3831152-2 REAR FLAP RETAINING STRAP 3831156 - - REAR FLAP RETAINING STRAP 5 3836100 2 - REAR DOOR BELTING 3836101-2 REAR DOOR BELTING 3836102 - - REAR DOOR BELTING 6 3837420 4 4 SUPPORT SPRING 7 600315 12 12 SUPPORT CLAMP 8 6D9017 35 37 LOCKNUT 2007 Alamo Group Inc. Parts Section 62
REAR FLAP - MODEL 6000 ITEM PART NO. QTY. DESCRIPTION 1 3830254 1 REAR FLAP - LH 2 3830245 1 REAR FLAP - RH 3 6D9017 36 LOCKNUT 4 600315 18 SUPPORT CLAMP 5 00011100 36 FLAT WASHER 6 3837420 6 SUPPORT SPRING 7 3836102 2 REAR DOOR BELTING 8 3831156 2 REAR FLAP RETAINING STRAP 9 00011400 18 BOLT 2007 Alamo Group Inc. Parts Section 63
LIGHT KIT - MODEL 4000, 5000 & 6000 ITEM PART NO. QTY. DESCRIPTION 1 2431606 4 LIGHT MOUNT BRACKET 2 3830285 4 LIGHT BRACKET 3 00015800 18 LOCKNUT 4 00011400 8 HEXBOLT 5 02816800 4 HEXNUT 6 370013C 4 LOCKWASHER 7 33105C 4 HEX JAMNUT 8 1458398 4 ORANGE REFLECTOR 9 1458392 4 RED REFLECTOR 10 00011100 18 FLATWASHER 11 2467901 2 DUAL RED/BLACK SIGNAL LAMP 12 2467900 2 DUAL AMBER/AMBER LAMP 13 2457900 1 MAIN WIRING HARNESS 14 2467903 1 PLUG HOLDER 15 2467902 1 WISHBONE HARNESS - 7 16 2467905 2 EXTENSION HARNESS - 5 2467906 2 EXTENSION HARNESS - 7 17 3263N13C 4 SCREW 18 329023C 6 LOCKNUT 19 3263N6C 2 SCREW 20 2417903 4 GROUND WIRE 21 0138629 12 TY-WRAP 22 3831733 2 WIRE COVER (NOT SHOWN) 2007 Alamo Group Inc. Parts Section 64
SIGNAL LAMPS - DUAL (AMBER) ITEM PART NO. QTY. DESCRIPTION 1 2417900 2 AMBER SIGNAL LAMP LENS 2 1417918 1 LIGHT BULB 3 02816800 1 HEXNUT 4 33105C 1 JAMNUT 5 370013C 1 WASHER 6 2417903 1 8" GROUND WIRE ASSEMBLY 2007 Alamo Group Inc. Parts Section 65
SIGNAL LAMPS - DUAL (RED) ITEM PART NO. QTY. DESCRIPTION 1 2417901 1 RED SIGNAL LAMP LENS 2 2417902 1 BLACK (BLANK) SIGNAL LENS 3 1417918 1 LIGHT BULB 4 02816800 1 HEXNUT 5 33105C 1 JAMNUT 6 370013C 1 WASHER 7 2417903 1 8" GROUND WIRE ASSEMBLY 2007 Alamo Group Inc. Parts Section 66
GREASE LINES AND SHIELDS - MODEL 6000 ITEM PART NO. QTY. DESCRIPTION 1 3831615 2 LEFT FRONT & RIGHT REAR OUTER SHIELD 2 3831614 2 RIGHT FRONT & LEFT REAR OUTER SHIELD 3 3831617 4 CENTER SHIELD 4 3831616 2 OUTER TOP SHIELD 5 3831732 1 CENTER TOP SHIELD 6 3830118 4 GREASE LINE - 28" 7 3830119 4 GREASE LINE - 42" 2007 Alamo Group Inc. Parts Section 67
TRIPLEX DRIVE TRANSMISSION ASSY 6000 S/N 10095 -Current Pub 08-06 2007 Alamo Group Inc. Parts Section 68
TRIPLEX DRIVE TRANSMISSION ASSY 6000 S/N 10095 -Current Pub 08-06 ITEM PART NO. QTY. DESCRIPTION 1 3836200 2 ROLLER CHAIN 2 3836351 2 SPROCKET 3 3812500 2 SPACER, FRONT SHAFT (USED ONLY ON TRIPLEX DRIVE ON SHORTER SHAFTS 4 552214 2 WASHER,SPECIAL FLAT 5 701615C 2 M16 LOCKWASHER 6 02961833 2 BOLT (USED ONLY WITH ITEMS 3 & 8) 7 3836350 2 SPROCKET 8 3812501 2 SPACER, REAR SHAFT (USED ONLY ON TRIPLEX DRIVE ON SHORTER SHAFTS 9 552215 2 WASHER,FLAT. 10 3830295 1 TENSIONER BRACKET - LH 11 3830294 1 TENSIONER BRACKET - RH 12 3830292 2 ROD SPRING GUIDE 13 212419 4 HEX LOCKNUT M16 X 1.5 14 552008 2 NUT,SPECIAL M16 X 1.5 X 62 15 15B1600 2 WASHER 1 SAE P 16 3837421 2 SPRING,HD COMPRESSION 17 3830293 2 BRACKET TENSIONER 18 3836775 6 TENSIONER,NYLON 19 312017H5C 4 HEX CAP 3/8-16 X 4 GR.5 20 00015800 4 NUT,TOPLOCK 3/8NC PLB 21 0401225 2 25MM DIA. EXTERNAL SNAP RING 22 3832525 2 PIN 23 214224 2 WASHER,FLAT 13 X 44.5 X 5 24 9313056 2 HEXB METRIC 12-P1.75-25MM PL5 25 9100206 2 WASHER,LOCK 12MM 30 1458430 4 WASHER,MACHINERY BUSHING - YDP 2007 Alamo Group Inc. Parts Section 69
LIMITED WARRANTY 1. LIMITED WARRANTIES 1.01.M&W warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( Purchaser ) and warrants for six months to the original commercial or industrial purchaser ( Purchaser ) that the goods purchased are free from defects in material or workmanship. 1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship. 1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your Operator s Manual. 1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer. 2. REMEDIES AND PROCEDURES. 2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase. 2.02.Purchaser claims must be made in writing to the Authorized Dealer ( Dealer ) from whom Purchaser purchased the goods or an approved Authorized Dealer ( Dealer ) within 30 days after Purchaser learns of the facts on which the claim is based. 2.03.Purchaser is responsible for returning the goods in question to the Dealer. 2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will: (a) (b) Repair or replace the defective goods or part(s) or Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory. 3. LIMITATION OF LIABILITY. 3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS. 3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER S LIABILITY HEREUNDER FOR DAMAGES INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS. 3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED. 4. MISCELLANEOUS. 4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas. 4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term. 4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein. 4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein. KEEP FOR YOUR RECORDS M&W ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. M&W Implement Model Serial Number Date Purchased Dealer ATTENTION: READ YOUR OPERATOR'S MANUAL M&W An Alamo Group Company 1020 South Sangamon Ave. Gibson City, Illinois 60936 217-784-4261
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
Dyna-Driver 08-06 Printed U.S.A. P/N 00771093P