INSTLLTION INSTRUTIONS FOR PRT 95-005 PPLITIONS DILL ELDORDO 1996-00 SEVILLE 1996-1997/1998-005 DEVILLE ONOURS (ONSOLE SHIFT)1996-1999 DEVILLE 000-005 95-005 KIT FETURES Double DIN Mount Radio Provision Stacked ISO Mount Radio Provision KIT OMPONENTS ) Double DIN Housing ) Double DIN rackets WIRING ND NTENN ONNETIONS (Sold Separately) Harness: GMR-0 - adillac hime Interface 1996-0 GMOS-06 - adillac ONSTR/MP interface 000-05 ntenna dapter: 40-GM10 - GM antenna adapter 1988-up TOOLS REQUIRED: Small Flat lade Screwdriver/ Panel Removal Tool Phillips Screwdriver Socket Set utting Tool
95-005 DSH DISSSEMLY 1 4 5 6 DILL ELDORDO 1996-00 DILL SEVILLE 1996-1997 Disconnect the negaive battery terminal to prevent an accidental short circuit. Remove -clip on forward facing side of shift knob and pull and remove knob. (Figure ) Remove () 9/ screws on each side of the ashtray assembly and (1) in the middle underneath ashtray insert. (Figure ) Insert a small flat blade screwdriver in between the radio and the switch panel at top of radio and pry up and out to remove switch panel. (Figure ) Remove (4) 9/ screws () from the top (Figure D) and () from the bottom to remove radio. (Figure E) Remove the () retaining nuts securing the radio and climate control to the factory bracket assembly and slide the climate control outward. (Figure F) ontinue to kit preparation. F Remove Retaining Nuts One Per Side E D
1 4 5 Disconnect the negaive battery terminal to prevent an accidental short circuit. Remove () 9/ screws on each side of the ashtray assembly and (1) in the middle underneath ashtray insert. (Figure ) Insert a small flat blade screwdriver in between the radio and the switch panel at top of radio and pry up and out to remove switch panel. (Figure ) Remove () 9/ screws (1) from the top (Figure ) and () from the bottom to remove radio. (Figure D) Remove the () retaining nuts securing the radio and climate control to the factory bracket assembly and slide the climate control outward. (Figure E) ontinue to kit preparation. 95-005 DSH DISSSEMLY DILL SEVILLE 1998-005 DILL DEVILLE ONOURS (ONSOLE SHIFT) 1996-1999 Remove Retaining Nuts One Per Side E D
95-005 DSH DISSSEMLY DILL DEVILLE 000-005 1 Disconnect the negaive battery terminal to prevent an accidental short circuit. Unsnap and remove panel surrounding climate controls and radio. (Figure ) Depress clips on both sides of radio and pull out to remove. (Figure ) ontinue to kit preparation.
95-005 KIT PREPRTION DILL ELDORDO 1996-00 DILL SEVILLE 1996-1997 NOTE: Refer also to the instructions included with the aftermarket radio. 1 adillac Eldorado 1996-00 and adillac Seville 1996-1997: Remove all tabs except the ones marked from the radio housing. (Figure ) 4 ttach the double DIN brackets to the double DIN radio housing. (Figure ) Slide the climate control assembly into the bracket/housing assembly and attach with the factory hardware. (Figure ) ontinue to kit assembly. ut front tab from bottom of the double DIN armiture on both sides. (Figure ) FRONT T HERE
95-005 KIT PREPRTION DILL SEVILLE 1998-005 DEVILLE ONOURS (console shift) 1996-1999 NOTE: Refer also to the instructions included with the aftermarket radio. 1 adillac Seville 1998-005 and Deville oncours 1996-1999: Remove all tabs except the ones marked from the radio housing. (Figure ) ttach the double DIN brackets to the double DIN radio housing. (Figure ) 4 Slide the climate control assembly into the bracket/housing assembly and attach with the factory hardware. (Figure ) ontinue to kit assembly. ut rear tab from bottom of the double DIN armiture on both sides. (Figure ) OLT RER T HERE
95-005 KIT PREPRTION DILL DEVILLE 000-005 1 adillac Deville 000-005 : Remove all tabs from the radio housing top. (Figure ) ttach the double DIN brackets to radio housing. Leave all side tabs on the double DIN brackets attached, but cut plastic armiture off below on each bracket at bottom, both sides. (Figure ) When installing the 95-005 assembly into the sub dash use the supplied (4) Phillips screws and mount in the locations shown. (Figure ) ontinue to kit assembly.
95-005 KIT SSEMLY DOULE DIN MOUNT RDIO PROVISION/ STKED ISO MOUNT UNIT(S) PROVISION NOTE: Refer also to the instructions included with the aftermarket radio. 1 Slide the Double DIN or stacked ISO mount units into the bracket/radio housing assembly and secure the Double DIN or stacked ISO mount units to the assembly using the screws supplied with the Double DIN or stacked ISO mount units. (Figure ) ontinue to final assembly.
95-005 FINL SSEMLY FINL SSEMLY () Strip wire ends back 1/" ) Twist ends together ) Solder D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING ODE 1V Ignition / cc.......... Red 1V att / Memory......... Yellow Ground.................. lack* Power ntenna............ lue mp Turn-On............. lue / White mp Ground.............. lack / White Illumination.............. Orange Dimmer................. Orange / White Right Front (+)............ Gray Right Front (-)............. Gray/ lack Left Front (+)............. White Left Front (-).............. White / lack Right Rear (+)............ Violet Right Rear (-)............. Violet / lack Left Rear (+)............. Green Left Rear (-).............. Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. METR ESSORIES STEREO DSH KITS